Add support for get_eeprom and get_eeprom_len ethtool ops
Specification states that PF software accesses NVM (shadow-ram) via AQ
commands (e.g. NVM Read, NVM Write) in the range 0x000000-0x00FFFF (64KB),
so the get_eeprom_len op should return 64KB. If additional regions of the
16MB NVM must be read, another access method must be used.
The ethtool kernel code, by default, will ask for multiple page-size hunks
of the NVM not to exceed the value returned by ice_get_eeprom_len().
ice_read_sr_buf() deals with arch page sizes different than 4KB.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add led blinking handler to ethtool. Since led blinking is
controlled by FW/HW only ETHTOOL_ID_ACTIVE and ETHTOOL_ID_INACTIVE
are really needed.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the physical link goes up or down, the driver is supposed to
receive a link status event (LSE). The driver currently has the code
to handle LSEs but there is no firmware support for this feature yet.
So this patch adds the ability for the driver to poll for link status
changes. The polling itself is done in ice_watchdog_subtask.
For namespace cleanliness, this patch also removes code that handles
LSE. This code will be reintroduced once the feature is officially
supported.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_dev_onetime_setup contains a couple of driver workarounds for current
firmware limitations. These workarounds are expected to go away once
these limitations are fixed in the firmware.
On a firmware release that has these issues addressed, these workarounds
(while unnecessary) will not break anything.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements parts of ice_sriov_configure and VF reset flow.
To create virtual functions (VFs), the user sets a value in num_vfs
through sysfs. This results in the kernel calling the handler for
.sriov_configure which is ice_sriov_configure.
VF setup first starts with a VF reset, followed by allocation of the VF
VSI using ice_vf_vsi_setup. Once the VF setup is complete a state bit
ICE_VF_STATE_INIT is set in the vf->states bitmap to indicate that
the VF is ready to go.
Also for VF reset to go into effect, it's necessary to issue a disable
queue command (ice_aqc_opc_dis_txqs). So this patch updates multiple
functions in the disable queue flow to take additional parameters that
distinguish if queues are being disabled due to VF reset.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We are currently replaying the link state of a port after a reset, but
it is possible that the link state of a port can change during the reset
process. So check for the current link state of a port during the rebuild
process of a reset.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, switch filters get replayed after reset. In addition to
filters, other VSI attributes (like RSS configuration, Tx scheduler
configuration, etc.) also need to be replayed after reset.
Thus, instead of replaying based on functional blocks (i.e. replay
all filters for all VSIs, followed by RSS configuration replay for
all VSIs, and so on), it makes more sense to have the replay centered
around a VSI. In other words, replay all configurations for a VSI before
moving on to rebuilding the next VSI.
To that effect, this patch introduces a VSI replay framework in a new
function ice_vsi_replay_all. Currently it only replays switch filters,
but it will be expanded in the future to replay additional VSI attributes.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is a continuation of the previous patch where VSI
handles are used instead of VSI numbers.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The functions that are used for PF VSI/netdev setup will also be used
for SR-IOV support. To allow reuse of these functions, move these
functions out of ice_main.c to ice_common.c/ice_lib.c
This move is done across multiple patches. Each patch moves a few
functions and may have minor adjustments. For example, a function that was
previously static in ice_main.c will be made non-static temporarily in
its new location to allow the driver to build cleanly. These adjustments
will be removed in subsequent patches where more code is moved out of
ice_main.c
In this particular patch, the following functions were moved out of
ice_main.c:
int ice_add_mac_to_list
ice_free_fltr_list
ice_stat_update40
ice_stat_update32
ice_update_eth_stats
ice_vsi_add_vlan
ice_vsi_kill_vlan
ice_vsi_manage_vlan_insertion
ice_vsi_manage_vlan_stripping
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To enable FW logging, the "cq_en" and "uart_en" enable bits of the
"fw_log" element in struct ice_hw need to set accordingly based on
some user-provided parameters during driver loading. To select which
FW log events to be emitted, the "cfg" elements of corresponding FW
modules in the "evnts" array member of "fw_log" need to be configured.
Signed-off-by: Hieu Tran <hieu.t.tran@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements handlers for ethtool get_link_ksettings and
set_link_ksettings. Helper functions use by these handlers are also
introduced in this patch.
Signed-off-by: Chinh Cao <chinh.t.cao@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Align Request Resource Ownership AQ command (0x0008) to the latest
specification. This includes:
- Correcting the resource IDs for the Global Cfg and Change locks.
- new enum ICE_CHANGE_LOCK_RES_ID
- new enum ICE_GLOBAL_CFG_LOCK_RES_ID
- Altering the flow for Global Config Lock to allow only the first PF to
download the package.
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements multiple pieces of functionality:
1. Added ice_vsi_sync_filters, which is called through the service task
to push filter updates to the hardware.
2. Add support to enable/disable promiscuous mode on an interface.
Enabling/disabling promiscuous mode on an interface results in
addition/removal of a promisc filter rule through ice_vsi_sync_filters.
3. Implement handlers for ndo_set_mac_address, ndo_change_mtu,
ndo_poll_controller and ndo_set_rx_mode.
This patch also marks the end of the driver addition by bumping up the
driver version.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Link events are posted to a PF's admin receive queue (ARQ). This patch
adds the ability to detect and process link events.
This patch also adds the ability to process resets.
The driver can process the following resets:
1) EMP Reset (EMPR)
2) Global Reset (GLOBR)
3) Core Reset (CORER)
4) Physical Function Reset (PFR)
EMPR is the largest level of reset that the driver can handle. An EMPR
resets the manageability block and also the data path, including PHY and
link for all the PFs. The affected PFs are notified of this event through
a miscellaneous interrupt.
GLOBR is a subset of EMPR. It does everything EMPR does except that it
doesn't reset the manageability block.
CORER is a subset of GLOBR. It does everything GLOBR does but doesn't
reset PHY and link.
PFR is a subset of CORER and affects only the given physical function.
In other words, PFR can be thought of as a CORER for a single PF. Since
only the issuing PF is affected, a PFR doesn't result in the miscellaneous
interrupt being triggered.
All the resets have the following in common:
1) Tx/Rx is halted and all queues are stopped.
2) All the VSIs and filters programmed for the PF are lost and have to be
reprogrammed.
3) Control queue interfaces are reset and have to be reprogrammed.
In the rebuild flow, control queues are reinitialized, VSIs are reallocated
and filters are restored.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds the ability for a VSI to use multiple Tx queues. More
specifically, the patch
1) Provides the ability to update the Tx scheduler tree in the
firmware. The driver can configure the Tx scheduler tree by
adding/removing multiple Tx queues per TC per VSI.
2) Allows a VSI to reconfigure its Tx queues during runtime.
3) Synchronizes the Tx scheduler update operations using locks.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for VLANs. When a VLAN is created a switch filter
is added to direct the VLAN traffic to the corresponding VSI. When a VLAN
is deleted, the filter is deleted as well.
This patch also adds support for the following hardware offloads.
1) VLAN tag insertion/stripping
2) Receive Side Scaling (RSS)
3) Tx checksum and TCP segmentation
4) Rx checksum
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch configures the VSIs to be able to send and receive
packets by doing the following:
1) Initialize flexible parser to extract and include certain
fields in the Rx descriptor.
2) Add Tx queues by programming the Tx queue context (implemented in
ice_vsi_cfg_txqs). Note that adding the queues also enables (starts)
the queues.
3) Add Rx queues by programming Rx queue context (implemented in
ice_vsi_cfg_rxqs). Note that this only adds queues but doesn't start
them. The rings will be started by calling ice_vsi_start_rx_rings on
interface up.
4) Configure interrupts for VSI queues.
5) Implement ice_open and ice_stop.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch continues the initialization flow as follows:
1) Allocate and initialize necessary fields (like vsi, num_alloc_vsi,
irq_tracker, etc) in the ice_pf instance.
2) Setup the miscellaneous interrupt handler. This also known as the
"other interrupt causes" (OIC) handler and is used to handle non
hotpath interrupts (like control queue events, link events,
exceptions, etc.
3) Implement a background task to process admin queue receive (ARQ)
events received by the driver.
CC: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds code to continue the initialization flow as follows:
1) Get PHY/link information and store it
2) Get default scheduler tree topology and store it
3) Get the MAC address associated with the port and store it
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds to the initialization flow by getting switch
configuration, scheduler configuration and device capabilities.
Switch configuration:
On boot, an L2 switch element is created in the firmware per physical
function. Each physical function is also mapped to a port, to which its
switch element is connected. In other words, this switch can be visualized
as an embedded vSwitch that can connect a physical function's virtual
station interfaces (VSIs) to the egress/ingress port. Egress/ingress
filters will be eventually created and applied on this switch element.
As part of the initialization flow, the driver gets configuration data
from this switch element and stores it.
Scheduler configuration:
The Tx scheduler is a subsystem responsible for setting and enforcing QoS.
As part of the initialization flow, the driver queries and stores the
default scheduler configuration for the given physical function.
Device capabilities:
As part of initialization, the driver has to determine what the device is
capable of (ex. max queues, VSIs, etc). This information is obtained from
the firmware and stored by the driver.
CC: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements multiple pieces of the initialization flow
as follows:
1) A reset is issued to ensure a clean device state, followed
by initialization of admin queue interface.
2) Once the admin queue interface is up, clear the PF config
and transition the device to non-PXE mode.
3) Get the NVM configuration stored in the device's non-volatile
memory (NVM) using ice_init_nvm.
CC: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A control queue is a hardware interface which is used by the driver
to interact with other subsystems (like firmware, PHY, etc.). It is
implemented as a producer-consumer ring. More specifically, an
"admin queue" is a type of control queue used to interact with the
firmware.
This patch introduces data structures and functions to initialize
and teardown control/admin queues. Once the admin queue is initialized,
the driver uses it to get the firmware version.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan