syzbot reports a divide-by-zero off the NBD_SET_BLKSIZE ioctl.
We need proper validation of the input here. Not just if it's
zero, but also if the value is a power-of-2 and in a valid
range. Add that.
Cc: stable@vger.kernel.org
Reported-by: syzbot <syzbot+25dbecbec1e62c6b0dd4@syzkaller.appspotmail.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The BTF conflicts were simple overlapping changes.
The virtio_net conflict was an overlap of a fix of statistics counter,
happening alongisde a move over to a bonafide statistics structure
rather than counting value on the stack.
Signed-off-by: David S. Miller <davem@davemloft.net>
The netlink policy should be const like other drivers.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the server or network is misbehaving and we get an unexpected reply
we can sometimes miss the request not being started and wait on a
request and never get a response, or even double complete the same
request. Fix this by replacing the send_complete completion with just a
per command lock. Add a per command cookie as well so that we can know
if we're getting a double completion for a previous event. Also check
to make sure we dont have REQUEUED set as that means we raced with the
timeout handler and need to just let the retry occur.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We can race with the snd timeout and the per-request timeout and end up
requeuing the same request twice. We can't use the send_complete
completion to tell if everything is ok because we hold the tx_lock
during send, so the timeout stuff will block waiting to mark the socket
dead, and we could be marked complete and still requeue. Instead add a
flag to the socket so we know whether we've been requeued yet.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If NBD_DISCONNECT_ON_CLOSE is set on a device, then the driver will
issue a disconnect from nbd_release if the device has no remaining
bdev->bd_openers.
Fix ret val so reconfigure with only setting the flag succeeds.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Doron Roberts-Kedes <doronrk@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Technically we should be able to get away with 0 as the
discard_alignment, but there's no way currently for the protocol to
indicate different alignments, and in real life most disks have
discard_alignment == discard_granularity. Just set our alignment to our
blocksize to make sure discards will actually work properly with 4k
drives.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Existing dev_dbg messages sometimes identify request using request
pointer, sometimes using nbd_cmd pointer. This makes it hard to
follow request flow. Consistently use request pointer instead.
Reviewed-by: Josef Bacik <jbacik@toxicpanda.com>
Signed-off-by: Kevin Vigor <kvigor@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We already check for started commands in all callbacks, but we should
also protect against already completed commands. Do this by taking
the checks to common code.
Acked-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When a userspace client requests a NBD device be disconnected, the
DISCONNECT_REQUESTED flag is set. While this flag is set, the driver
will not inform userspace when a connection is closed.
Unfortunately the flag was never cleared, so once a disconnect was
requested the driver would thereafter never tell userspace about a
closed connection. Thus when connections failed due to timeout, no
attempt to reconnect was made and eventually the device would fail.
Fix by clearing the DISCONNECT_REQUESTED flag (and setting the
DISCONNECTED flag) once all connections are closed.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Kevin Vigor <kvigor@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
By completing the request entirely in the driver we can remove the
BLK_EH_HANDLED return value and thus the split responsibility between the
driver and the block layer that has been causing trouble.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The BLK_EH_NOT_HANDLED implies nothing happen, but very often that
is not what is happening - instead the driver already completed the
command. Fix the symbolic name to reflect that a little better.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Convert the S_<FOO> symbolic permissions to their octal equivalents as
using octal and not symbolic permissions is preferred by many as more
readable.
see: https://lkml.org/lkml/2016/8/2/1945
Done with automated conversion via:
$ ./scripts/checkpatch.pl -f --types=SYMBOLIC_PERMS --fix-inplace <files...>
Miscellanea:
o Wrapped modified multi-line calls to a single line where appropriate
o Realign modified multi-line calls to open parenthesis
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
For some reason we had discard granularity set to 512 always even when
discards were disabled. Fix this by having the default be 0, and then
if we turn it on set the discard granularity to the blocksize.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add WQ_UNBOUND to the knbd-recv workqueue so we're not bound
to a single CPU that is selected at device creation time.
Signed-off-by: Dan Melnic <dmm@fb.com>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We need to make sure we don't just set the size of the bdev to 0 while
it's being used by a file system. We have the appropriate check in
nbd_bdev_reset, simply use that helper instead.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
bd_invalidated is kind of a pain wrt partitions as it really only
triggers the partition rescan if it is set after bd_ops->open() runs, so
setting it when we reset the device isn't useful. We also sporadically
would still have partitions left over in some disconnect cases, so fix
this by always setting bd_invalidated on open if there's no
configuration or if we've had a disconnect action happen, that way the
partition table gets invalidated and rescanned properly.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This is what the ioctl based nbd disconnect does as well. Without this
the device will just sit there and wait for the connection to go away
(or IO to occur) before the device gets torn down. Instead clear
everything up on our end so the configuration goes away as quickly as
possible.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When we stopped relying on the bdev everywhere I broke updating the
block device size on the fly, which ceph relies on. We can't just do
set_capacity, we also have to do bd_set_size so things like parted will
notice the device size change.
Fixes: 29eaadc ("nbd: stop using the bdev everywhere")
cc: stable@vger.kernel.org
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
I messed up changing the size of an NBD device while it was connected by
not actually updating the device or doing the uevent. Fix this by
updating everything if we're connected and we change the size.
cc: stable@vger.kernel.org
Fixes: 639812a ("nbd: don't set the device size until we're connected")
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This fixes a use after free bug, we shouldn't be doing disk->queue right
after we do del_gendisk(disk). Save the queue and do the cleanup after
the del_gendisk.
Fixes: c6a4759ea0 ("nbd: add device refcounting")
cc: stable@vger.kernel.org
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch has been generated as follows:
for verb in set_unlocked clear_unlocked set clear; do
replace-in-files queue_flag_${verb} blk_queue_flag_${verb%_unlocked} \
$(git grep -lw queue_flag_${verb} drivers block/bsg*)
done
Except for protecting all queue flag changes with the queue lock
this patch does not change any functionality.
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
It seems that the proper value to return in this particular case is the
one contained into variable new_index instead of ret.
Addresses-Coverity-ID: 1465148 ("Copy-paste error")
Fixes: e46c7287b1 ("nbd: add a basic netlink interface")
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull core block layer updates from Jens Axboe:
"This is the main pull request for block storage for 4.15-rc1.
Nothing out of the ordinary in here, and no API changes or anything
like that. Just various new features for drivers, core changes, etc.
In particular, this pull request contains:
- A patch series from Bart, closing the whole on blk/scsi-mq queue
quescing.
- A series from Christoph, building towards hidden gendisks (for
multipath) and ability to move bio chains around.
- NVMe
- Support for native multipath for NVMe (Christoph).
- Userspace notifications for AENs (Keith).
- Command side-effects support (Keith).
- SGL support (Chaitanya Kulkarni)
- FC fixes and improvements (James Smart)
- Lots of fixes and tweaks (Various)
- bcache
- New maintainer (Michael Lyle)
- Writeback control improvements (Michael)
- Various fixes (Coly, Elena, Eric, Liang, et al)
- lightnvm updates, mostly centered around the pblk interface
(Javier, Hans, and Rakesh).
- Removal of unused bio/bvec kmap atomic interfaces (me, Christoph)
- Writeback series that fix the much discussed hundreds of millions
of sync-all units. This goes all the way, as discussed previously
(me).
- Fix for missing wakeup on writeback timer adjustments (Yafang
Shao).
- Fix laptop mode on blk-mq (me).
- {mq,name} tupple lookup for IO schedulers, allowing us to have
alias names. This means you can use 'deadline' on both !mq and on
mq (where it's called mq-deadline). (me).
- blktrace race fix, oopsing on sg load (me).
- blk-mq optimizations (me).
- Obscure waitqueue race fix for kyber (Omar).
- NBD fixes (Josef).
- Disable writeback throttling by default on bfq, like we do on cfq
(Luca Miccio).
- Series from Ming that enable us to treat flush requests on blk-mq
like any other request. This is a really nice cleanup.
- Series from Ming that improves merging on blk-mq with schedulers,
getting us closer to flipping the switch on scsi-mq again.
- BFQ updates (Paolo).
- blk-mq atomic flags memory ordering fixes (Peter Z).
- Loop cgroup support (Shaohua).
- Lots of minor fixes from lots of different folks, both for core and
driver code"
* 'for-4.15/block' of git://git.kernel.dk/linux-block: (294 commits)
nvme: fix visibility of "uuid" ns attribute
blk-mq: fixup some comment typos and lengths
ide: ide-atapi: fix compile error with defining macro DEBUG
blk-mq: improve tag waiting setup for non-shared tags
brd: remove unused brd_mutex
blk-mq: only run the hardware queue if IO is pending
block: avoid null pointer dereference on null disk
fs: guard_bio_eod() needs to consider partitions
xtensa/simdisk: fix compile error
nvme: expose subsys attribute to sysfs
nvme: create 'slaves' and 'holders' entries for hidden controllers
block: create 'slaves' and 'holders' entries for hidden gendisks
nvme: also expose the namespace identification sysfs files for mpath nodes
nvme: implement multipath access to nvme subsystems
nvme: track shared namespaces
nvme: introduce a nvme_ns_ids structure
nvme: track subsystems
block, nvme: Introduce blk_mq_req_flags_t
block, scsi: Make SCSI quiesce and resume work reliably
block: Add the QUEUE_FLAG_PREEMPT_ONLY request queue flag
...
We can end up sleeping for a while waiting for the dead timeout, which
means we could get the per request timer to fire. We did handle this
case, but if the dead timeout happened right after we submitted we'd
either tear down the connection or possibly requeue as we're handling an
error and race with the endio which can lead to panics and other
hilarity.
Fixes: 560bc4b399 ("nbd: handle dead connections")
Cc: stable@vger.kernel.org
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If we have a pending signal or the user kills their application then
it'll bring down the whole device, which is less than awesome. Instead
wait uninterruptible for the dead timeout so we're sure we gave it our
best shot.
Fixes: 560bc4b399 ("nbd: handle dead connections")
Cc: stable@vger.kernel.org
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If you do not set sk_sndtimeo you will get -ERESTARTSYS if there is a
pending signal when you enter sendmsg, which we handle properly.
However if you set a timeout for your commands we'll set sk_sndtimeo to
that timeout, which means that sendmsg will start returning -EINTR
instead of -ERESTARTSYS. Fix this by checking either cases and doing
the correct thing.
Cc: stable@vger.kernel.org
Fixes: dc88e34d69 ("nbd: set sk->sk_sndtimeo for our sockets")
Reported-and-tested-by: Daniel Xu <dlxu@fb.com>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A user reported a regression with using the normal ioctl interface on
newer kernels. This happens because I was setting the device size
before the device was actually connected, which caused us to error out
and close everything down. This didn't happen on netlink because we
hold the device lock the whole time we're setting things up, but we
don't do that for the ioctl path. This fixes the problem.
Cc: stable@vger.kernel.org
Fixes: 29eaadc ("nbd: stop using the bdev everywhere")
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Christoph made it so that if we return'ed BLK_STS_RESOURCE whenever we
got ERESTARTSYS from sending our packets we'd return BLK_STS_OK, which
means we'd never requeue and just hang. We really need to return the
right value from the upper layer.
Fixes: fc17b6534e ("blk-mq: switch ->queue_rq return value to blk_status_t")
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In testing we noticed that nbd would spew if you ran a fio job against
the raw device itself. This is because fio calls a block device
specific ioctl, however the block layer will first pass this back to the
driver ioctl handler in case the driver wants to do something special.
Since the device was setup using netlink this caused us to spew every
time fio called this ioctl. Since we don't have special handling, just
error out for any non-nbd specific ioctl's that come in. This fixes the
spew.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Make this const as is is only passed as an argument to the
function device_create_file and device_remove_file and the corresponding
arguments are of type const.
Done using Coccinelle
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There's no reason to have partitions disabled for nbd by default, it costs us
nothing to have it enabled and is just confusing/obnoxious to users who try to
use partitions with nbd.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If users really want to use a particular index for their nbd device and it
doesn't already exist there's no reason we can't just create it for them. Do
this instead of erroring out.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If our device loses its connection for longer than the dead timeout we
will set NBD_DISCONNECTED in order to quickly fail any pending IO's that
flood in after the IO's that were waiting during the dead timer.
However if we re-connect at some point in the future we'll still see
this DISCONNECTED flag set if we then lose our connection again after
that, which means we won't get notifications for our newly lost
connections. Fix this by just clearing the DISCONNECTED flag on
reconnect in order to make sure everything works as it's supposed to.
Reported-by: Dan Melnic <dmm@fb.com>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A user reported that he was getting immediate disconnects with my
sndtimeo patch applied. This is because by default the OSS nbd client
doesn't set a timeout, so we end up setting the sndtimeo to 0, which of
course means we have send errors a lot. Instead only set our sndtimeo
if the user specified a timeout, otherwise we'll just wait forever like
we did previously.
Fixes: dc88e34d69 ("nbd: set sk->sk_sndtimeo for our sockets")
Reported-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We need to take the tx_lock so we don't interleave our disconnect
request between real data going down the wire.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There's no reason to limit ourselves to one disconnect message per
socket. Sometimes networks do strange things, might as well let
sysadmins hit the panic button as much as they want.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
No need to return value in queue work, kill ret variable.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Unlike blk_mq_stop_hw_queues, blk_mq_quiesce_queue respects the
submission path rcu grace. quiesce the queue before iterating
on live tags.
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Acked-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZPdbLAAoJEHm+PkMAQRiGx4wH/1nCjfnl6fE8oJ24/1gEAOUh
biFdqJkYZmlLYHVtYfLm4Ueg4adJdg0wx6qM/4RaAzmQVvLfDV34bc1qBf1+P95G
kVF+osWyXrZo5cTwkwapHW/KNu4VJwAx2D1wrlxKDVG5AOrULH1pYOYGOpApEkZU
4N+q5+M0ce0GJpqtUZX+UnI33ygjdDbBxXoFKsr24B7eA0ouGbAJ7dC88WcaETL+
2/7tT01SvDMo0jBSV0WIqlgXwZ5gp3yPGnklC3F4159Yze6VFrzHMKS/UpPF8o8E
W9EbuzwxsKyXUifX2GY348L1f+47glen/1sedbuKnFhP6E9aqUQQJXvEO7ueQl4=
=m2Gx
-----END PGP SIGNATURE-----
Merge tag 'v4.12-rc5' into for-4.13/block
We've already got a few conflicts and upcoming work depends on some of the
changes that have gone into mainline as regression fixes for this series.
Pull in 4.12-rc5 to resolve these conflicts and make it easier on down stream
trees to continue working on 4.13 changes.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Use the same values for use for request completion errors as the return
value from ->queue_rq. BLK_STS_RESOURCE is special cased to cause
a requeue, and all the others are completed as-is.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently we use nornal Linux errno values in the block layer, and while
we accept any error a few have overloaded magic meanings. This patch
instead introduces a new blk_status_t value that holds block layer specific
status codes and explicitly explains their meaning. Helpers to convert from
and to the previous special meanings are provided for now, but I suspect
we want to get rid of them in the long run - those drivers that have a
errno input (e.g. networking) usually get errnos that don't know about
the special block layer overloads, and similarly returning them to userspace
will usually return somethings that strictly speaking isn't correct
for file system operations, but that's left as an exercise for later.
For now the set of errors is a very limited set that closely corresponds
to the previous overloaded errno values, but there is some low hanging
fruite to improve it.
blk_status_t (ab)uses the sparse __bitwise annotations to allow for sparse
typechecking, so that we can easily catch places passing the wrong values.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
If the nbd server stops receiving packets altogether we will get stuck
waiting for them to receive indefinitely as the tcp buffer will never
empty, which looks like a deadlock. Fix this by setting the sk send
timeout to our configured timeout, that way if the server really
misbehaves we'll disconnect cleanly instead of waiting forever.
Reported-by: Dan Melnic <dmm@fb.com>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
NBD userland client and server have FUA (forced unit access) support
and flags defined. Make NBD kernel module recognize NBD_FLAG_SEND_FUA,
enable FUA on the queue, and forward FUA requests to the server.
Signed-off-by: Shaun McDowell <shaunjmcdowell@gmail.com>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
nbd_config is allocated in nbd_alloc_config(), but never freed.
Fixes: 5ea8d10802 ("nbd: separate out the config information")
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
There is nothing to clear -- nbd_device has just been allocated.
Fold nbd_reset() into its other caller, nbd_config_put().
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We now have memalloc_noreclaim_{save,restore} helpers for robust setting
and clearing of PF_MEMALLOC. Let's convert the code which was using the
generic tsk_restore_flags(). No functional change.
[vbabka@suse.cz: in net/core/sock.c the hunk is missing]
Link: http://lkml.kernel.org/r/20170405074700.29871-4-vbabka@suse.cz
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Josef Bacik <jbacik@fb.com>
Cc: Lee Duncan <lduncan@suse.com>
Cc: Chris Leech <cleech@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Wouter Verhelst <w@uter.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull block fixes and updates from Jens Axboe:
"Some fixes and followup features/changes that should go in, in this
merge window. This contains:
- Two fixes for lightnvm from Javier, fixing problems in the new code
merge previously in this merge window.
- A fix from Jan for the backing device changes, fixing an issue in
NFS that causes a failure to mount on certain setups.
- A change from Christoph, cleaning up the blk-mq init and exit
request paths.
- Remove elevator_change(), which is now unused. From Bart.
- A fix for queue operation invocation on a dead queue, from Bart.
- A series fixing up mtip32xx for blk-mq scheduling, removing a
bandaid we previously had in place for this. From me.
- A regression fix for this series, fixing a case where we wait on
workqueue flushing from an invalid (non-blocking) context. From me.
- A fix/optimization from Ming, ensuring that we don't both quiesce
and freeze a queue at the same time.
- A fix from Peter on lock ordering for CPU hotplug. Not a real
problem right now, but will be once the CPU hotplug rework goes in.
- A series from Omar, cleaning up out blk-mq debugfs support, and
adding support for exporting info from schedulers in debugfs as
well. This is really useful in debugging stalls or livelocks. From
Omar"
* 'for-linus' of git://git.kernel.dk/linux-block: (28 commits)
mq-deadline: add debugfs attributes
kyber: add debugfs attributes
blk-mq-debugfs: allow schedulers to register debugfs attributes
blk-mq: untangle debugfs and sysfs
blk-mq: move debugfs declarations to a separate header file
blk-mq: Do not invoke queue operations on a dead queue
blk-mq-debugfs: get rid of a bunch of boilerplate
blk-mq-debugfs: rename hw queue directories from <n> to hctx<n>
blk-mq-debugfs: don't open code strstrip()
blk-mq-debugfs: error on long write to queue "state" file
blk-mq-debugfs: clean up flag definitions
blk-mq-debugfs: separate flags with |
nfs: Fix bdi handling for cloned superblocks
block/mq: Cure cpu hotplug lock inversion
lightnvm: fix bad back free on error path
lightnvm: create cmd before allocating request
blk-mq: don't use sync workqueue flushing from drivers
mtip32xx: convert internal commands to regular block infrastructure
mtip32xx: cleanup internal tag assumptions
block: don't call blk_mq_quiesce_queue() after queue is frozen
...
Pull networking updates from David Millar:
"Here are some highlights from the 2065 networking commits that
happened this development cycle:
1) XDP support for IXGBE (John Fastabend) and thunderx (Sunil Kowuri)
2) Add a generic XDP driver, so that anyone can test XDP even if they
lack a networking device whose driver has explicit XDP support
(me).
3) Sparc64 now has an eBPF JIT too (me)
4) Add a BPF program testing framework via BPF_PROG_TEST_RUN (Alexei
Starovoitov)
5) Make netfitler network namespace teardown less expensive (Florian
Westphal)
6) Add symmetric hashing support to nft_hash (Laura Garcia Liebana)
7) Implement NAPI and GRO in netvsc driver (Stephen Hemminger)
8) Support TC flower offload statistics in mlxsw (Arkadi Sharshevsky)
9) Multiqueue support in stmmac driver (Joao Pinto)
10) Remove TCP timewait recycling, it never really could possibly work
well in the real world and timestamp randomization really zaps any
hint of usability this feature had (Soheil Hassas Yeganeh)
11) Support level3 vs level4 ECMP route hashing in ipv4 (Nikolay
Aleksandrov)
12) Add socket busy poll support to epoll (Sridhar Samudrala)
13) Netlink extended ACK support (Johannes Berg, Pablo Neira Ayuso,
and several others)
14) IPSEC hw offload infrastructure (Steffen Klassert)"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2065 commits)
tipc: refactor function tipc_sk_recv_stream()
tipc: refactor function tipc_sk_recvmsg()
net: thunderx: Optimize page recycling for XDP
net: thunderx: Support for XDP header adjustment
net: thunderx: Add support for XDP_TX
net: thunderx: Add support for XDP_DROP
net: thunderx: Add basic XDP support
net: thunderx: Cleanup receive buffer allocation
net: thunderx: Optimize CQE_TX handling
net: thunderx: Optimize RBDR descriptor handling
net: thunderx: Support for page recycling
ipx: call ipxitf_put() in ioctl error path
net: sched: add helpers to handle extended actions
qed*: Fix issues in the ptp filter config implementation.
qede: Fix concurrency issue in PTP Tx path processing.
stmmac: Add support for SIMATIC IOT2000 platform
net: hns: fix ethtool_get_strings overflow in hns driver
tcp: fix wraparound issue in tcp_lp
bpf, arm64: fix jit branch offset related to ldimm64
bpf, arm64: implement jiting of BPF_XADD
...
Remove the request_idx parameter, which can't be used safely now that we
support I/O schedulers with blk-mq. Except for a superflous check in
mtip32xx it was unused anyway.
Also pass the tag_set instead of just the driver data - this allows drivers
to avoid some code duplication in a follow on cleanup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Jens Axboe