In case of interlace mode video processor registers and mixer config
register must be check to ensure internal state is in sync with shadow
registers.
This patch fixes page-faults in interlaced mode.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The output stage of the mixer uses YCbCr for the internal
computations, which is the reason that some registers take
YCbCr related data as input. In particular this applies
to MXR_BG_COLOR{0,1,2} and MXR_CM_COEFF_{Y,CB,CR}.
Document the formatting of the data which we write to
these registers.
While at it, unify wording of comments in the register header.
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Properly configure blending properties of given hardware layer based on
the selected pixel format. Currently only per-pixel-based alpha is possible
when respective pixel format has been selected. Configuration of global,
per-plane alpha value, color key and background color will be added later.
This patch is heavily inspired by earlier work done by Tobias Jakobi
<tjakobi@math.uni-bielefeld.de>.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
'zpos' plane property is configurable, so adjust hardware layers
priority based on the zpos value. 'zpos' value shifted by one can be
used directly as hw priority value and stored to the registers, because
mixer accepts priority values from 1 to 15 (0 means that layer is
disabled).
This patch also changes the default layer priority to match already
exposed initial zpos values. The initial configuration is now:
[top] video > gfx layer1 > gfx layer0 [bottom].
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Mixer should be power gated only after it is gracefully stopped.
The recommended sequence is to Stop the mixer and wait till
it enters to IDLE state before gating the clocks and power to
the mixer.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Add support for exynos5420 mixer IP in the drm mixer driver.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch is hdmi display support for exynos drm driver.
There is already v4l2 based exynos hdmi driver in drivers/media/video/s5p-tv
and some low level code is already in s5p-tv and even headers for register
define are almost same. but in this patch, we decide not to consider separated
common code with s5p-tv.
Exynos HDMI is composed of 5 blocks, mixer, vp, hdmi, hdmiphy and ddc.
1. mixer. The piece of hardware responsible for mixing and blending multiple
data inputs before passing it to an output device. The mixer is capable of
handling up to three image layers. One is the output of VP. Other two are
images in RGB format. The blending factor, and layers' priority are controlled
by mixer's registers. The output is passed to HDMI.
2. vp (video processor). It is used for processing of NV12/NV21 data. An image
stored in RAM is accessed by DMA. The output in YCbCr444 format is send to
mixer.
3. hdmi. The piece of HW responsible for generation of HDMI packets. It takes
pixel data from mixer and transforms it into data frames. The output is send
to HDMIPHY interface.
4. hdmiphy. Physical interface for HDMI. Its duties are sending HDMI packets to
HDMI connector. Basically, it contains a PLL that produces source clock for
mixer, vp and hdmi.
5. ddc (display data channel). It is dedicated i2c channel to exchange display
information as edid with display monitor.
With plane support, exynos hdmi driver fully supports two mixer layes and vp
layer. Also vp layer supports multi buffer plane pixel formats having non
contigus memory spaces.
In exynos drm driver, common drm_hdmi driver to interface with drm framework
has opertion pointers for mixer and hdmi. this drm_hdmi driver is registered as
sub driver of exynos_drm. hdmi has hdmiphy and ddc i2c clients and controls
them. mixer controls all overlay layers in both mixer and vp.
Vblank interrupts for hdmi are handled by mixer internally because drm
framework cannot support multiple irq id. And pipe number is used to check
which display device irq happens.
History
v2: this version
- drm plane feature support to handle overlay layers.
- multi buffer plane pixel format support for vp layer.
- vp layer support
RFCv1: original
- at https://lkml.org/lkml/2011/11/4/164
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Andrzej Hajda