The davinci spi driver provides an option to use DMA transfers for
data. In the dma_map_single() call, the driver is passing the
number of words to be transfered for the mapping size. It should
be the number of bytes.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The function gen_74x164_remove and mc33880_remove are used only wrapped
by __devexit_p so define it using __devexit.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The device table is required to load modules based on modaliases.
After adding MODULE_DEVICE_TABLE, below entries will be added to modules.pcimap:
pch_gpio 0x00008086 0x00008803 0xffffffff 0xffffffff 0x00000000 0x00000000 0x0
ml_ioh_gpio 0x000010db 0x0000802e 0xffffffff 0xffffffff 0x00000000 0x00000000 0x0
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
mpc23s17 is very similar to the mcp23s08, except that registers are 16bit
wide, so extend the interface to work with both variants.
The s17 variant also has an additional address pin, so adjust platform
data structure to support up to 8 devices per SPI chipselect.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: index i shadowed in 2nd loop
drm/nv50-nvc0: prevent multiple vm/bar flushes occuring simultanenously
drm/nouveau: fix regression causing ttm to not be able to evict vram
drm/i915: Rebind the buffer if its alignment constraints changes with tiling
drm/i915: Disable GPU semaphores by default
drm/i915: Do not overflow the MMADDR write FIFO
Revert "drm/i915: fix corruptions on i8xx due to relaxed fencing"
This fixes a bug introduced by 807e8e4067 ("mmc: Fix sd/sdio/mmc
initialization frequency retries") that prevented SDIO drivers from
performing SDIO commands in their probe routines -- the above patch
called mmc_claim_host() before sdio_add_func(), which causes a deadlock
if an external SDIO driver calls sdio_claim_host().
Fix tested on an OLPC XO-1.75 with libertas on SDIO.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Reviewed-and-Tested-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
* ickle/drm-intel-fixes:
drm/i915: Rebind the buffer if its alignment constraints changes with tiling
drm/i915: Disable GPU semaphores by default
drm/i915: Do not overflow the MMADDR write FIFO
Revert "drm/i915: fix corruptions on i8xx due to relaxed fencing"
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] tape: deadlock on system work queue
[S390] keyboard: integer underflow bug
[S390] xpram: remove __initdata attribute from module parameters
The per-vm mutex doesn't prevent this completely, a flush coming from the
BAR VM could potentially happen at the same time as one for the channel
VM. Not to mention that if/when we get per-client/channel VM, this will
happen far more frequently.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
TTM assumes an error condition from man->func->get_node() means that
something went horribly wrong, and causes it to bail.
The driver is supposed to return 0, and leave mm_node == NULL to
signal that it couldn't allocate any memory.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Early gen3 and gen2 chipset do not have the relaxed per-surface tiling
constraints of the later chipsets, so we need to check that the GTT
alignment is correct for the new tiling. If it is not, we need to
rebind.
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Andi Kleen narrowed his GPU hangs on his Sugar Bay (SNB desktop) rev 09
down to the use of GPU semaphores, and we already know that they appear
broken up to Huron River (mobile) rev 08. (I'm optimistic that disabling
GPU semaphores is simply hiding another bug by the latency and
side-effects of the additional device interaction it introduces...)
However, use of semaphores is a massive performance improvement... Only
as long as the system remains stable. Enable at your peril.
Reported-by: Andi Kleen <andi-fd@firstfloor.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=33921
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If a virtio-console device gets unplugged while a port is open, a
subsequent close() call on the port accesses vqs to free up buffers.
This can lead to a crash.
The buffers are already freed up as a result of the call to
unplug_ports() from virtcons_remove(). The fix is to simply not access
vq information if port->portdev is NULL.
Reported-by: juzhang <juzhang@redhat.com>
CC: stable@kernel.org
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Whilst the GT is powered down (rc6), writes to MMADDR are placed in a
FIFO by the System Agent. This is a limited resource, only 64 entries, of
which 20 are reserved for Display and PCH writes, and so we must take
care not to queue up too many writes. To avoid this, there is counter
which we can poll to ensure there are sufficient free entries in the
fifo.
"Issuing a write to a full FIFO is not supported; at worst it could
result in corruption or a system hang."
Reported-and-Tested-by: Matt Turner <mattst88@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=34056
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This reverts commit c2e0eb1670.
As it turns out, userspace already depends upon being able to enable
tiling on existing bo which it promises to be large enough for its
purposes i.e. it will not access beyond the end of the last full-tile
row.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35016
Reported-and-tested-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If an SPI access was not a multiple of the SPI word size,
the while() loop would spin and the rx/tx ptrs would be incremented
indefinitely.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver causes hard lockups, when the active clock soure is jiffies.
The reason is that it loops with interrupts disabled waiting for a
timestamp to be reached by polling getnstimeofday(). Though with a
jiffies clocksource, when that code runs on the same CPU which is
responsible for updating jiffies, then we loop in circles for ever
simply because the timer interrupt cannot update jiffies. So both UP
and SMP can be affected.
There is no easy fix for that problem so make it depend on BROKEN for
now.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Alexander Gordeev <lasaine@lvk.cs.msu.su>
Cc: Rodolfo Giometti <giometti@linux.it>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The device table is required to load modules based on modaliases.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Shubhrajyoti D <shubhrajyoti@ti.com>
Cc: Christoph Mair <christoph.mair@gmail.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix s3c_rtc_setaie() prototype to eliminate the following compile
warning:
drivers/rtc/rtc-s3c.c:383: warning: initialization from incompatible pointer type
(akpm: the rtc_class_ops.alarm_irq_enable() handler is being passed two
arguments where it expects just one, presumably with undesired effects)
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The nv30/nv40 3d driver is about to start using DMA_FENCE from the 3D
object which, it turns out, doesn't like its DMA object to not be
aligned to a 4KiB boundary.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
MAINTAINERS: Add Andy Gospodarek as co-maintainer.
r8169: disable ASPM
RxRPC: Fix v1 keys
AF_RXRPC: Handle receiving ACKALL packets
cnic: Fix lost interrupt on bnx2x
cnic: Prevent status block race conditions with hardware
net: dcbnl: check correct ops in dcbnl_ieee_set()
e1000e: disable broken PHY wakeup for ICH10 LOMs, use MAC wakeup instead
igb: fix sparse warning
e1000: fix sparse warning
netfilter: nf_log: avoid oops in (un)bind with invalid nfproto values
dccp: fix oops on Reset after close
ipvs: fix dst_lock locking on dest update
davinci_emac: Add Carrier Link OK check in Davinci RX Handler
bnx2x: update driver version to 1.62.00-6
bnx2x: properly calculate lro_mss
bnx2x: perform statistics "action" before state transition.
bnx2x: properly configure coefficients for MinBW algorithm (NPAR mode).
bnx2x: Fix ethtool -t link test for MF (non-pmf) devices.
bnx2x: Fix nvram test for single port devices.
...
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: kill loop_mutex
blktrace: Remove blk_fill_rwbs_rq.
block: blk-flush shouldn't call directly into q->request_fn() __blk_run_queue()
block: add @force_kblockd to __blk_run_queue()
block: fix kernel-doc format for blkdev_issue_zeroout
blk-throttle: Do not use kblockd workqueue for throtl work
For some time is known that ASPM is causing troubles on r8169, i.e. make
device randomly stop working without any errors in dmesg.
Currently Tomi Leppikangas reports that system with r8169 device hangs
with MCE errors when ASPM is enabled:
https://bugzilla.redhat.com/show_bug.cgi?id=642861#c4
Lets disable ASPM for r8169 devices at all, to avoid problems with
r8169 PCIe devices at least for some users.
Reported-by: Tomi Leppikangas <tomi.leppikangas@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 34xx and 3590 tape driver uses the system work queue to defer work
from the interrupt function to process context, e.g. a medium sense
after an unsolicited interrupt. The tape commands started by the work
handler need to be asynchronous, otherwise a deadlock on the system
work queue can occur.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The "ct" variable should be an unsigned int. Both struct kbdiacrs
->kb_cnt and struct kbd_data ->accent_table_size are unsigned ints.
Making it signed causes a problem in KBDIACRUC because the user could
set the signed bit and cause a buffer overflow.
Cc: <stable@kernel.org>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The module parameter 'devs' and 'sizes' are marked as __initdata. The
memory for the parameters are freed after module_init completed. This
can lead to kernel crashes in param_free_charp. Remove the __initdata
attribute to fix the problem.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* 'devicetree/merge' of git://git.secretlab.ca/git/linux-2.6:
of/promtree: allow DT device matching by fixing 'name' brokenness (v5)
x86: OLPC: have prom_early_alloc BUG rather than return NULL
of/flattree: Drop an uninteresting message to pr_debug level
of: Add missing of_address.h to xilinx ehci driver
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: Avoid tps6586x burst writes
mfd: Don't suspend WM8994 if the CODEC is not suspended
mfd: Fix DaVinci voice codec device name
mfd: Fix NULL pointer due to non-initialized ucb1x00-ts absinfo
mfd: Fix ASIC3 build with GENERIC_HARDIRQS_NO_DEPRECATED
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] p4-clockmod: print EST-capable warning message only once
[CPUFREQ] fix BUG on cpufreq policy init failure
[CPUFREQ] Fix another notifier leak in powernow-k8.
[CPUFREQ] Missing "unregister_cpu_notifier" in powernow-k8.c
We service 2 queues (kcq1 and kcq2) in cnic_service_bnx2x_bh(). If
the status block index has changed when servicing the kcq2, we must
go back and check kcq1. The latest status block index will be used
to acknowledge the interrupt, and without looping back to check kcq1,
we may miss events on kcq1.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The status block index is used to acknowledge interrupt events and must
be read before checking for the interrupt events, so we need to add rmb()
to guarantee that.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e2f2a93b, "of/promtree: add package-to-path support to pdt"
changed dp->name from using the 'name' property to using
package-to-path. This fixed /proc/device-tree creation by eliminating
conflicts between names (the 'name' property provides names like
'battery', whereas package-to-path provides names like
'/foo/bar/battery@0', which we stripped to 'battery@0'). However, it
also breaks of_device_id table matching.
The fix that we _really_ wanted was to keep dp->name based upon
the name property ('battery'), but based dp->full_name upon
package-to-path ('battery@0'). This patch does just that.
This changes all users (except SPARC) of promtree to use the full
result from package-to-path for full_name, rather than stripping the
directory out. In practice, the strings end up being exactly the
same; this change saves time, code, and memory.
SPARC continues to use the existing build_path_component() code.
v2: combine two patches and revert of_pdt_node_name to original version
v3: use dp->phandle instead of passing around node
v4: warn/bail out for non-sparc archs if pkg2path is not set
v5: split of_pdt_build_full_name into sparc & non-sparc versions
v6: Pass NULL to pkg2path before buf gets assigned.
Drop check for pkg2path hook on each and every node.
v7: Don't BUG() when unable to get the full_path; create a
known-unique name instead.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Build log:
In file included from drivers/usb/host/ehci-hcd.c:1208:
drivers/usb/host/ehci-xilinx-of.c: In function 'ehci_hcd_xilinx_of_probe':
drivers/usb/host/ehci-xilinx-of.c:168: error: implicit declaration of function 'of_address_to_resource'
Signed-off-by: John Williams <john.williams@petalogix.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
__blk_run_queue() automatically either calls q->request_fn() directly
or schedules kblockd depending on whether the function is recursed.
blk-flush implementation needs to be able to explicitly choose
kblockd. Add @force_kblockd.
All the current users are converted to specify %false for the
parameter and this patch doesn't introduce any behavior change.
stable: This is prerequisite for fixing ide oops caused by the new
blk-flush implementation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jan Beulich <JBeulich@novell.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
When support for 82577/82578 was added[1] in 2.6.31, PHY wakeup was in-
advertently enabled (even though it does not function properly) on ICH10
LOMs. This patch makes it so that the ICH10 LOMs use MAC wakeup instead
as was done with the initial support for those devices (i.e. 82567LM-3,
82567LF-3 and 82567V-4).
[1] commit a4f58f5455
Reported-by: Aurelien Jarno <aurelien@aurel32.net>
Cc: <stable@kernel.org>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reported-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sparse complains because the e1000 driver is calling ioread on a pointer
not tagged as __iomem.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
tps6586 does not support burst writes. i2c writes have to be
1 byte at a time.
Cc: stable@kernel.org
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
ASoC supports keeping the audio subsysetm active over suspend in order
to support use cases such as audio passthrough from a cellular modem
with the main CPU suspended. Ensure that we don't power down the CODEC
when this is happening by checking to see if VMID is up and skipping
suspend and resume when it is. If the CODEC has suspended then it'll
turn VMID off before the core suspend() gets called.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Michael Williamson