The i.MX35 has two bits per clock gate which are decoded as follows:
0b00 -> clock off
0b01 -> clock is on in run mode, off in wait/doze
0b10 -> clock is on in run/wait mode, off in doze
0b11 -> clock is always on
The reset value for the MAX clock is 0b10.
The MAX clock is needed by the SoC, yet unused in the Kernel, so the
common clock framework will disable it during late init time. It will
only disable clocks though which it detects as being turned on. This
detection is made depending on the lower bit of the gate. If the reset
value has been altered by the bootloader to 0b11 the clock framework
will detect the clock as turned on, yet unused, hence it will turn it
off and the system locks up.
This patch turns the MAX clock on unconditionally making the Kernel
independent of the bootloader.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The i.MX25 DT machine descriptor calls a non existing imx25_timer_init()
function. This patch adds it to fix compilation.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We always boot from PLL1, so let's have pll1_sys in the clks_init_on
list to have clk prepare/enable use count match the hardware status,
so that drivers managing pll1_sys like cpufreq can get the use count
right from the start.
Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Building the kernel with allyesconfig fails because the i.mx early
resume code located in the .data section is unable to fixup the bl
relocation as the branch target gets too far away.
The idea of having code in the .data section allows for easy access to
nearby data using relative addressing while the MMU is off. However it
is probably best to move the code back to the .text section where it
belongs and fixup the data access instead. This solves the bl reloc
issue (at least until this becomes a general problem) and simplifies
the code as well.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This branch contains of devicetree changes for the Freescale i.MX platform.
The base patch of the branch changes the format of the dts files to a
slightly different format that makes it easier to do derivative board
definitions, but it also introduces a lot of churn in the process since
every line of the file is touched.
On top of that are a handful of the regular changes; enabling more boards
as DT-based instead of legacy board files (mx25pdk), enabling another
driver for devicetree and thus adding bindings (onewire), etc.
I'm not happy about the churn, and will likely not take it for other platforms
in the future.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=72aL
-----END PGP SIGNATURE-----
Merge tag 'late-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC i.MX DT changes from Olof Johansson:
"This branch contains of devicetree changes for the Freescale i.MX
platform.
The base patch of the branch changes the format of the dts files to a
slightly different format that makes it easier to do derivative board
definitions, but it also introduces a lot of churn in the process
since every line of the file is touched.
On top of that are a handful of the regular changes; enabling more
boards as DT-based instead of legacy board files (mx25pdk), enabling
another driver for devicetree and thus adding bindings (onewire), etc.
I'm not happy about the churn, and will likely not take it for other
platforms in the future."
* tag 'late-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
ARM: dts: add dtsi for imx6q and imx6dl
ARM: dts: rename imx6q.dtsi to imx6qdl.dtsi
ARM: dts: i.MX6: Add regulator delay support
ARM: dts: Add device tree entry for onewire master on i.MX53
ARM: i.MX53: Add clocks for i.mx53 onewire master.
W1: Add device tree support to MXC onewire master.
ARM: imx: enable imx6q-cpufreq support
ARM: dts: Add apf51 basic support
ARM i.MX6: change mxs usbphy clock usage
ARM: dts: imx6q: Remove silicon version from SDMA firmware
ARM i.MX53: dts: add oftree for MBa53 baseboard
ARM i.MX53: add dts for the TQ tqma53 module
ARM: dts: imx53: pinctrl update
ARM i.MX51 babbage: Add keypad support
ARM: dts: imx: Add imx51 KPP entry
ARM: dts: imx25-karo-tx25: Put status entry in the end
ARM: mx25pdk: Add device tree support
ARM: dts: imx: use nodes label in board dts
ARM: dts: add missing imx dtb targets
ARM: boot: dts: Add an entry for imx27-pdk.dtb
...
This is a larger set of new functionality for the existing SoC families,
including:
* vt8500 gains support for new CPU cores, notably the Cortex-A9 based wm8850
* prima2 gains support for the "marco" SoC family, its SMP based cousin
* tegra gains support for the new Tegra4 (Tegra114) family
* socfpga now supports a newer version of the hardware including SMP
* i.mx31 and bcm2835 are now using DT probing for their clocks
* lots of updates for sh-mobile
* OMAP updates for clocks, power management and USB
* i.mx6q and tegra now support cpuidle
* kirkwood now supports PCIe hot plugging
* tegra clock support is updated
* tegra USB PHY probing gets implemented diffently
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=PRrg
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC-specific updates from Arnd Bergmann:
"This is a larger set of new functionality for the existing SoC
families, including:
- vt8500 gains support for new CPU cores, notably the Cortex-A9 based
wm8850
- prima2 gains support for the "marco" SoC family, its SMP based
cousin
- tegra gains support for the new Tegra4 (Tegra114) family
- socfpga now supports a newer version of the hardware including SMP
- i.mx31 and bcm2835 are now using DT probing for their clocks
- lots of updates for sh-mobile
- OMAP updates for clocks, power management and USB
- i.mx6q and tegra now support cpuidle
- kirkwood now supports PCIe hot plugging
- tegra clock support is updated
- tegra USB PHY probing gets implemented diffently"
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (148 commits)
ARM: prima2: remove duplicate v7_invalidate_l1
ARM: shmobile: r8a7779: Correct TMU clock support again
ARM: prima2: fix __init section for cpu hotplug
ARM: OMAP: Consolidate OMAP USB-HS platform data (part 3/3)
ARM: OMAP: Consolidate OMAP USB-HS platform data (part 1/3)
arm: socfpga: Add SMP support for actual socfpga harware
arm: Add v7_invalidate_l1 to cache-v7.S
arm: socfpga: Add entries to enable make dtbs socfpga
arm: socfpga: Add new device tree source for actual socfpga HW
ARM: tegra: sort Kconfig selects for Tegra114
ARM: tegra: enable ARCH_REQUIRE_GPIOLIB for Tegra114
ARM: tegra: Fix build error w/ ARCH_TEGRA_114_SOC w/o ARCH_TEGRA_3x_SOC
ARM: tegra: Fix build error for gic update
ARM: tegra: remove empty tegra_smp_init_cpus()
ARM: shmobile: Register ARM architected timer
ARM: MARCO: fix the build issue due to gic-vic-to-irqchip move
ARM: shmobile: r8a7779: Correct TMU clock support
ARM: mxs_defconfig: Select CONFIG_DEVTMPFS_MOUNT
ARM: mxs: decrease mxs_clockevent_device.min_delta_ns to 2 clock cycles
ARM: mxs: use apbx bus clock to drive the timers on timrotv2
...
A large number of cleanups, all over the platforms. This is dominated
largely by the Samsung platforms (s3c, s5p, exynos) and a few of the
others moving code out of arch/arm into more appropriate subsystems.
The clocksource and irqchip drivers are now abstracted to the point
where platforms that are already cleaned up do not need to even specify
the driver they use, it can all get configured from the device tree
as we do for normal device drivers. The clocksource changes basically
touch every single platform in the process.
We further clean up the use of platform specific header files here,
with the goal of turning more of the platforms over to being
"multiplatform" enabled, which implies that they cannot expose
their headers to architecture independent code any more.
It is expected that no functional changes are part of the cleanup.
The overall reduction in total code lines is mostly the result of
removing broken and obsolete code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIVAwUAUSUyKmCrR//JCVInAQIN8RAAnb/uPytmlMjn5yCksF4Mvb/FVbn/TVwz
KRIGpCHOzyKK1q7pM8NRUVWfjW2SZqbXJFqx6zBGKSlDPvFTOhsLyyupU+Tnyu5W
IX4eIUBwb+a6H7XDHw0X2YI8uHzi5RNLhne0A1QyDKcnuHs1LDAttXnJHaK4Ap6Y
NN2YFt3l3ld7DXWXJtMsw5v8lC10aeIFGTvXefaPDAdeMLivmI57qEUMDXknNr7W
Odz/Rc0/cw3BNBVl/zNHA0jw7FOjKAymCYYNUa4xDCJEr+JnIRTqizd0N/YIIC7x
aA2xjJ3oKUFyF51yiJE6nFuTyJznhwtehc+uiMOSIkjrPLym52LEHmd7G5Yqlmjz
oiei09qBb870q3lGxwfht9iaeIwYgQFYGfD0yW5QWArCO5pxhtCPLPH7YZNZtcQd
ZJRSGGqT/ljBz3bm0K9OLESeeTTN7+Nxvtpiz/CD+Piegz0gWJzDYJRTzkJ3UWpA
WTVhVQdWUeX2JrNkgM7Z3Tu8iXOe+LIEs7kVXGJZSREmIIZiRvR36UrODZtAkp9I
7YQ+srX/uaR832pgK0RrHK0zY0psU6MmIvhYxJZFbx7keiPA9eH6drb0x7tGqcUD
FzEUzvcZvyqppndfBi+R60H/YKAhJDEXdwxzo6dyCpPQaW1T9GnzIqXuE1zin+Aw
X7Y8YywMbHI=
=DvgJ
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"A large number of cleanups, all over the platforms. This is dominated
largely by the Samsung platforms (s3c, s5p, exynos) and a few of the
others moving code out of arch/arm into more appropriate subsystems.
The clocksource and irqchip drivers are now abstracted to the point
where platforms that are already cleaned up do not need to even
specify the driver they use, it can all get configured from the device
tree as we do for normal device drivers. The clocksource changes
basically touch every single platform in the process.
We further clean up the use of platform specific header files here,
with the goal of turning more of the platforms over to being
"multiplatform" enabled, which implies that they cannot expose their
headers to architecture independent code any more.
It is expected that no functional changes are part of the cleanup.
The overall reduction in total code lines is mostly the result of
removing broken and obsolete code."
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (133 commits)
ARM: mvebu: correct gated clock documentation
ARM: kirkwood: add missing include for nsa310
ARM: exynos: move exynos4210-combiner to drivers/irqchip
mfd: db8500-prcmu: update resource passing
drivers/db8500-cpufreq: delete dangling include
ARM: at91: remove NEOCORE 926 board
sunxi: Cleanup the reset code and add meaningful registers defines
ARM: S3C24XX: header mach/regs-mem.h local
ARM: S3C24XX: header mach/regs-power.h local
ARM: S3C24XX: header mach/regs-s3c2412-mem.h local
ARM: S3C24XX: Remove plat-s3c24xx directory in arch/arm/
ARM: S3C24XX: transform s3c2443 subirqs into new structure
ARM: S3C24XX: modify s3c2443 irq init to initialize all irqs
ARM: S3C24XX: move s3c2443 irq code to irq.c
ARM: S3C24XX: transform s3c2416 irqs into new structure
ARM: S3C24XX: modify s3c2416 irq init to initialize all irqs
ARM: S3C24XX: move s3c2416 irq init to common irq code
ARM: S3C24XX: Modify s3c_irq_wake to use the hwirq property
ARM: S3C24XX: Move irq syscore-ops to irq-pm
clocksource: always define CLOCKSOURCE_OF_DECLARE
...
This resolves one non-obvious merge conflict between the imx cpuidle
patches and the imx DT changes for 3.9.
Conflicts:
arch/arm/mach-imx/mach-imx6q.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
MACH_MX31ADS_WM1133_EV1 already depends on REGULATOR_WM8350,
but that still allows REGULATOR_WM8350 to be a loadable
module. Depending on REGULATOR_WM8350 to be built-in
ensures we cannot create a broken configuration.
Without this patch, building allmodconfig results in:
arch/arm/mach-imx/built-in.o: In function `mx31_wm8350_init':
arch/arm/mach-imx/mach-mx31ads.c:461: undefined reference to `wm8350_register_regulator'
arch/arm/mach-imx/mach-mx31ads.c:471: undefined reference to `wm8350_dcdc_set_slot'
arch/arm/mach-imx/mach-mx31ads.c:473: undefined reference to `wm8350_isink_set_flash'
arch/arm/mach-imx/mach-mx31ads.c:480: undefined reference to `wm8350_dcdc25_set_mode'
arch/arm/mach-imx/mach-mx31ads.c:485: undefined reference to `wm8350_register_led'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Axel Lin <axel.lin@gmail.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
From Dinh Nguyen, this is a series of patches introducing support for
socfpga hardware (Altera Cyclone5). It also includes a cleanup that
moves some of the ARMv7 cache maintenance functions to a common location,
since three other platforms aready implemented it separately.
* socfpga/hw:
arm: socfpga: Add SMP support for actual socfpga harware
arm: Add v7_invalidate_l1 to cache-v7.S
arm: socfpga: Add entries to enable make dtbs socfpga
arm: socfpga: Add new device tree source for actual socfpga HW
Trivial conflict in arch/arm/mach-tegra/headsmp.S.
Signed-off-by: Olof Johansson <olof@lixom.net>
mach-socfpga is another platform that needs to use
v7_invalidate_l1 to bringup additional cores. There was a comment that
the ideal place for v7_invalidate_l1 should be in arm/mm/cache-v7.S
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Pavel Machek <pavel@denx.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Olof Johansson <olof@lixom.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Update operating-points per hardware document and add support for
1 GHz and 1.2 GHz frequencies.
400 MHz, 800 MHz and 1 GHz should be supported by all i.MX6Q chips,
while 1.2 GHz support needs to know from OTP fuse bit.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This mxs usbphy is only needs to be on after system boots
up, and software never needs to control it anymore.
Meanwhile, usbphy's parent needs to be notified if usb
is suspend or not. So we design below mxs usbphy usage:
- usbphy1_gate and usbphy2_gate:
Their parents are dummy clock, we only needs to enable
it after system boots up.
- usbphy1 and usbphy2
Usage reserved bit for this clock, in that case, the refcount
will be updated, but without hardware changing.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The mxc-timer on the imx25 needs to be derived from the AHB clock.
If a bootloader reparents this clock to the ipg_clk_highfreq, which according
to the datasheet is a valid operation, the system can/will produce lockups/
freezes after some time [1].
This can be forced with code like
while(1)
syscall(SYS_clock_gettime, CLOCK_REALTIME, &tp);
This was already fixed with the commit
"i.MX25 GPT clock fix: ensure correct the clock source" [2],
for 3.1-rc2, but was lost, when i.MX was converted to the common clock framework
("ARM i.MX25: implement clocks using common clock framework") [3]
[1]: http://lists.arm.linux.org.uk/lurker/message/20130129.161230.229bda17.en.html
[2]: 2012d9ca2a
[3]: 6bbaec5676
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: stable@vger.kernel.org # v3.5+
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
spi-imx driver needs two clock: ipg and per. The first clock must be named and
the second must be added.
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- It's based on imx-cleanup-3.9 to avoid conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRCRzjAAoJEFBXWFqHsHzOOTYH/2YiAhCXDoovJ++leTTBKoFO
kRx2gvV0oxQYAjvRX4IiiwcuWjbCQI8ugiKxeH9Vn+jwHD8jKqzTINEUVQfKUud6
s8AI1/EqKwKnEFYFs/Fg6WxZHuHpoL/clpRB/5wZw1KoChmte2OnVU7d9vOt67iN
l0P4nPR18iwU5LFoDCnqMX50Dp9C56KEF2JhzBCQKW9TtRclwpcBNy6AsHb/TNOe
/nHN+Ku6/3xQEz2MPQ9QdmgFxnp9Pr8R6leJNg1Vg6UGRYrKxy0zVo+oFEXAZuUw
v6gnhdlvO6Ki/IKHcWkw7Q7pUDTuB6SttirQE9mBlPdc0V3kTU82SVtX9WAQhSs=
=rVol
-----END PGP SIGNATURE-----
Merge tag 'imx6q-cpudile-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/soc
From Shawn Guo:
imx6q cpuidle support for 3.9
- It's based on imx-cleanup-3.9 to avoid conflicts.
* tag 'imx6q-cpudile-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx6q: support WAIT mode using cpuidle
ARM: imx: move imx6q_cpuidle_driver into a separate file
ARM: imx: mask gpc interrupts initially
ARM: imx: return zero in case next event gets a large increment
ARM: imx: Remove mx508 support
ARM: imx: Remove mach-mx51_3ds board
ARM: imx: use debug_ll_io_init() for imx6q
ARM: imx: remove unused imx6q_clock_map_io()
ARM: mach-imx: Kconfig: Do not select Babbage for MACH_IMX51_DT
Signed-off-by: Olof Johansson <olof@lixom.net>
Still, two delete/change conflicts caused by imx/cleanup:
arch/arm/mach-imx/mach-mx50_rdp.c
arch/arm/mach-imx/mach-mx51_3ds.c
Commit 6bb27d7 "ARM: delete struct sys_timer" caused the following:
arch/arm/mach-imx/imx31-dt.c:56:2: warning: initialization from incompatible pointer type [enabled by default]
arch/arm/mach-imx/imx31-dt.c:56:2: warning: (near initialization for ‘__mach_desc_IMX31_DT.init_time’) [enabled by default]
This is because mx31_clocks_init_dt() returns int, whereas the .init_time
field prototype expects a function returning void. Implement a wrapper so
that the prototypes match.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add WAIT mode (ARM core clock gating) support to imx6q cpuidle driver.
As WAIT mode is broken on imx6q TO 1.0 and 1.1, it only enables the
support for revision 1.2 with chicken bit set.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Move imx6q_cpuidle_driver into a separate file as more codes will
be added when WAIT mode gets implemented as cpuidle.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The return of v2_set_next_event() will lead to an infinite loop in
tick_handle_oneshot_broadcast() - "goto again;" with imx6q WAIT mode
(to be enabled). This happens because when global event did not expire
any CPU local events, the broadcast device will be rearmed to a CPU
local next_event, which could be far away from now and result in a
max_delta_tick programming in set_next_event().
Fix the problem by detecting those next events with increments larger
than 0x7fffffff, and simply return zero in that case.
It leaves mx1_2_set_next_event() unchanged since only v2_set_next_event()
will be running with imx6q WAIT mode support.
Thanks Russell King for helping understand the problem.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
in question and other dts related changes, and will have them go via DT
branch to save the cross branch dependency.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRB24TAAoJEFBXWFqHsHzO3RcH/22Qe0+BUjxj1NBrBjBee6YE
ymb2CIOaTM2PgAQJZDgqGa4zgbPK7bcLu6fSyyg+XzExaxZ/CQI0EuKjMSroiyoB
6tRB76dz9ESWO4QYrQH65QxdY5Bi3VYDXv9+NeOdl0lzHR1wJp/Eeqvx608+aKIa
ps5Db1OdJn5TZ1o8Ye+/m4BUFBp+6feTx3fFfgXdes61eZskJLokURQz9zA6qiDw
s6YCBt1lNSNG/duZD3uFichDSPi/h+YFWwinI+deakRUDNUIs4n8ofToc99N6zWd
iKTbWX1cWOJpAYHKHS2lCaKF0saIpqCt7jhz/wmyXwDCrSSWsmwQSpxc5xmhFXU=
=LfVI
-----END PGP SIGNATURE-----
Merge tag 'imx-cleanup-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/cleanup
From Shawn Guo:
IMX cleanup for 3.9:
* Remove lluart.c by using debug_ll_io_init()
* Remove mach-mx51_3ds board support
* Remove imx50 support which has been BROKEN for cycles
* Other trival cleanups
* tag 'imx-cleanup-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx: Remove mx508 support
ARM: imx: Remove mach-mx51_3ds board
ARM: imx: use debug_ll_io_init() for imx6q
ARM: imx: remove unused imx6q_clock_map_io()
ARM: mach-imx: Kconfig: Do not select Babbage for MACH_IMX51_DT
Signed-off-by: Olof Johansson <olof@lixom.net>
Change/delete conflicts due to some of the previous sweeping cleanups in:
arch/arm/mach-imx/mach-mx50_rdp.c
arch/arm/mach-imx/mach-mx51_3ds.c
Only mx508 based board is mach-mx50_rdp and it has been marked as BROKEN
for several releases.
mx508 currently lacks clock support.
In case someone needs to add mx508 support back, then the recommended approach
is to use device tree.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
mach-mx51_3ds only supports old silicon version of MX51 and was replaced
with mx51 babbage, which is the official MX51 development board.
No need to maintain it anymore.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Use debug_ll_io_init() to map low level debug port for imx6q, so that
arch/arm/mach-imx/lluart.c can be removed.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
imx6q_clock_map_io() becomes an empty function since imx6q clock driver
is moved to common clock framework. It's used nowhere now. Remove it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Mostly clock related updates, most notably the conversion of
i.MX31 to a DT based lookup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=bWtE
-----END PGP SIGNATURE-----
Merge tag 'imx-soc' of git://git.pengutronix.de/git/imx/linux-2.6 into next/soc
From Sascha Hauer:
ARM i.MX SoC updates for next
Mostly clock related updates, most notably the conversion of
i.MX31 to a DT based lookup.
* tag 'imx-soc' of git://git.pengutronix.de/git/imx/linux-2.6:
ARM: clk-imx35: Fix build warnings with W=1
ARM: imx27: add a clock gate to activate SPLL clock
ARM: mx31: Replace clk_register_clkdev with clock DT lookup
ARM: clk-imx31: Add dummy clock
ARM: Let CONFIG_MACH_IMX31_DT be built by default
Signed-off-by: Olof Johansson <olof@lixom.net>
Fix the following warnings when building with W=1 option:
arch/arm/mach-imx/clk-imx35.c: In function 'mx35_clocks_init':
arch/arm/mach-imx/clk-imx35.c:70:12: warning: old-style function definition [-Wold-style-definition]
arch/arm/mach-imx/clk-imx35.c:201:16: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
A clock gate is mandatory to activate SPLL clock needed, at least, for usb.
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Similarly as it was done for mx6q, use a DT lookup in order to make maintainance
task for the clock devices easier.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add dummy clock as it is required by some i.mx drivers.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Here's a long-pending fixes pull request for arm-soc (I didn't send one
in the -rc4 cycle).
The larger deltas are from:
- A fixup of error paths in the mvsdio driver
- Header file move for a driver that hadn't been properly converted to
multiplatform on i.MX, which was causing build failures when included
- Device tree updates for at91 dealing mostly with their new
pinctrl setup merged in 3.8 and mistakes in those initial configs
The rest are the normal mix of small fixes all over the place; sunxi,
omap, imx, mvebu, etc, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=YDHs
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Here's a long-pending fixes pull request for arm-soc (I didn't send
one in the -rc4 cycle).
The larger deltas are from:
- A fixup of error paths in the mvsdio driver
- Header file move for a driver that hadn't been properly converted
to multiplatform on i.MX, which was causing build failures when
included
- Device tree updates for at91 dealing mostly with their new pinctrl
setup merged in 3.8 and mistakes in those initial configs
The rest are the normal mix of small fixes all over the place; sunxi,
omap, imx, mvebu, etc, etc."
* tag 'fixes-for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (40 commits)
mfd: vexpress-sysreg: Don't skip initialization on probe
ARM: vexpress: Enable A7 cores in V2P-CA15_A7's Device Tree
ARM: vexpress: extend the MPIDR range used for pen release check
ARM: at91/dts: correct comment in at91sam9x5.dtsi for mii
ARM: at91/at91_dt_defconfig: add at91sam9n12 SoC to DT defconfig
ARM: at91/at91_dt_defconfig: remove memory specification to cmdline
ARM: at91/dts: add macb mii pinctrl config for kizbox
ARM: at91: rm9200: remake the BGA as default version
ARM: at91: fix gpios on i2c-gpio for RM9200 DT
ARM: at91/at91sam9x5 DTS: add SCK USART pins
ARM: at91/at91sam9x5 DTS: correct wrong PIO BANK values on u(s)arts
ARM: at91/at91-pinctrl documentation: fix typo and add some details
ARM: kirkwood: fix missing #interrupt-cells property
mmc: mvsdio: use devm_ API to simplify/correct error paths.
clk: mvebu/clk-cpu.c: fix memory leakage
ARM: OMAP2+: omap4-panda: add UART2 muxing for WiLink shared transport
ARM: OMAP2+: DT node Timer iteration fix
ARM: OMAP2+: Fix section warning for omap_init_ocp2scp()
ARM: OMAP2+: fix build break for omapdrm
ARM: OMAP2: Fix missing omap2xxx_clkt_vps_late_init function calls
...
This contains a single compilation fix for the CODA driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=7H1R
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-rc' of git://git.pengutronix.de/git/imx/linux-2.6 into fixes
From Sascha Hauer:
ARM i.MX fixes for -rc.
This contains a single compilation fix for the CODA driver.
* tag 'imx-fixes-rc' of git://git.pengutronix.de/git/imx/linux-2.6:
[media] coda: Fix build due to iram.h rename
As we use platform_device_id for fsl-usb2-udc driver, it needs to
change clk connection-id, or the related devm_clk_get will be failed.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As mach/hardware.h is deleted, we need to use platform_device_id to
differentiate SoCs. Besides, one cpu_is_mx35 is useless as it has
already used pdata to differentiate runtime
Meanwhile we update the platform code accordingly.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
From Kukjin Kim:
That branch fixes build error for S3C24XX/S3C64xx. And corrects dw-mshc
properties on EXYNOS5 DT and fixes IRQ mapping on Cragganmore board.
* 'v3.8-samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S3C64XX: Fix up IRQ mapping for balblair on Cragganmore
ARM: dts: correct the dw-mshc timing properties as per binding
ARM: S3C64XX: Fix build error with CONFIG_S3C_DEV_FB disabled
+ Linux 3.8-rc3
Signed-off-by: Olof Johansson <olof@lixom.net>
This creates irqchip initialization infrastructure from Thomas
Petazzoni. The VIC and GIC irqchip code is moved to drivers/irqchips
and adapted to use the new infrastructure. All DT enabled platforms
using GIC and VIC are converted over to use the new irqchip_init.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQ8ZobAAoJEMhvYp4jgsXiihIH/2VvxmSHZb0e3jN6AR0B42b7
9EwX0IE0B23t91hNTwdzzmTJQYA7pMmWkgHNfd3vIeqSepJAmrVv/gp4iM9CtPwE
KNh+kDWOK2ZsOH4Vb0lYRJHN8WQOIQHuCUr9+MdYLNOgf/pPL6G/Y9kv9A1e7fTC
W+tFRjC5N1ilZMGyowX12L1wnwDk6kHzed6YV6bskC17cZ9/pg8PhSVbM4A/3kAv
NXYKqbXJb+eCsWGXg/knZXOL6V9gBwvVYoe4O9X3nQ0226AWB9caad8l8tchAjRB
fmrYF1tbkpOWPnLxhvQy5b5MJichJgTMJHh7RgiEcc/3f63kOljjlx4QKiqHvT0=
=q7gm
-----END PGP SIGNATURE-----
Merge tag 'gic-vic-to-irqchip' of git://sources.calxeda.com/kernel/linux into next/cleanup
From Rob Herring:
Initial irqchip init infrastructure and GIC and VIC clean-ups
This creates irqchip initialization infrastructure from Thomas
Petazzoni. The VIC and GIC irqchip code is moved to drivers/irqchips
and adapted to use the new infrastructure. All DT enabled platforms
using GIC and VIC are converted over to use the new irqchip_init.
* tag 'gic-vic-to-irqchip' of git://sources.calxeda.com/kernel/linux:
irqchip: Move ARM vic.h to include/linux/irqchip/arm-vic.h
ARM: picoxcell: use common irqchip_init function
ARM: spear: use common irqchip_init function
irqchip: Move ARM VIC to drivers/irqchip
ARM: samsung: remove unused tick.h
ARM: remove unneeded vic.h includes
ARM: remove mach .handle_irq for VIC users
ARM: VIC: set handle_arch_irq in VIC initialization
ARM: VIC: shrink down vic.h
irqchip: Move ARM gic.h to include/linux/irqchip/arm-gic.h
ARM: use common irqchip_init for GIC init
irqchip: Move ARM GIC to drivers/irqchip
ARM: remove mach .handle_irq for GIC users
ARM: GIC: set handle_arch_irq in GIC initialization
ARM: GIC: remove direct use of gic_raise_softirq
ARM: GIC: remove assembly ifdefs from gic.h
ARM: mach-ux500: use SGI0 to wake up the other core
arm: add set_handle_irq() to register the parent IRQ controller handler function
irqchip: add basic infrastructure
irqchip: add to the directories part of the IRQ subsystem in MAINTAINERS
Fixed up massive merge conflicts with the timer cleanup due to adjacent changes:
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/mach-bcm/board_bcm.c
arch/arm/mach-cns3xxx/cns3420vb.c
arch/arm/mach-ep93xx/adssphere.c
arch/arm/mach-ep93xx/edb93xx.c
arch/arm/mach-ep93xx/gesbc9312.c
arch/arm/mach-ep93xx/micro9.c
arch/arm/mach-ep93xx/simone.c
arch/arm/mach-ep93xx/snappercl15.c
arch/arm/mach-ep93xx/ts72xx.c
arch/arm/mach-ep93xx/vision_ep9307.c
arch/arm/mach-highbank/highbank.c
arch/arm/mach-imx/mach-imx6q.c
arch/arm/mach-msm/board-dt-8960.c
arch/arm/mach-netx/nxdb500.c
arch/arm/mach-netx/nxdkn.c
arch/arm/mach-netx/nxeb500hmi.c
arch/arm/mach-nomadik/board-nhk8815.c
arch/arm/mach-picoxcell/common.c
arch/arm/mach-realview/realview_eb.c
arch/arm/mach-realview/realview_pb1176.c
arch/arm/mach-realview/realview_pb11mp.c
arch/arm/mach-realview/realview_pba8.c
arch/arm/mach-realview/realview_pbx.c
arch/arm/mach-socfpga/socfpga.c
arch/arm/mach-spear13xx/spear1310.c
arch/arm/mach-spear13xx/spear1340.c
arch/arm/mach-spear13xx/spear13xx.c
arch/arm/mach-spear3xx/spear300.c
arch/arm/mach-spear3xx/spear310.c
arch/arm/mach-spear3xx/spear320.c
arch/arm/mach-spear3xx/spear3xx.c
arch/arm/mach-spear6xx/spear6xx.c
arch/arm/mach-tegra/board-dt-tegra20.c
arch/arm/mach-tegra/board-dt-tegra30.c
arch/arm/mach-u300/core.c
arch/arm/mach-ux500/board-mop500.c
arch/arm/mach-ux500/cpu-db8500.c
arch/arm/mach-versatile/versatile_ab.c
arch/arm/mach-versatile/versatile_dt.c
arch/arm/mach-versatile/versatile_pb.c
arch/arm/mach-vexpress/v2m.c
include/asm-generic/vmlinux.lds.h
Clockevent cleanup series from Shawn Guo.
Resolved move/change conflict in mach-pxa/time.c due to the sys_timer
cleanup.
* clocksource/cleanup:
clocksource: use clockevents_config_and_register() where possible
ARM: use clockevents_config_and_register() where possible
clockevents: export clockevents_config_and_register for module use
+ sync to Linux 3.8-rc3
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/mach-pxa/time.c
The clockevent core is able to figure out the best mult and shift,
calculate min_delta_ns and max_delta_ns, with the necessary info passed
into clockevents_config_and_register(). Use this combined configure
and register function where possible to make the codes less error prone
and gain some positive diff stat.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: Anton Vorontsov <cbouatmailru@gmail.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Tested-by: Roland Stigge <stigge@antcom.de>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: David Brown <davidb@codeaurora.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Barry Song <baohua.song@csr.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
The hardware reset value of bit CCM_CLPCR_LPM enables WAIT mode
(WAIT_UNCLOCKED) by default. However this is undesirable because
WAIT mode should only be enabled when there is a driver managing
ARM clock gating. Correct the initial power mode to WAIT_CLOCKED
(disable WAIT mode). While at it, the power mode after resuming
is also set back to WAIT_CLOCKED from STOP_POWER_OFF.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It's buggy to disable the cpu that is being hot-unplugged in .cpu_die
hook which runs on the cpu itself. Instead, it should be done in
.cpu_kill which runs on the thread (another cpu) that asks for shutting
down the cpu. Move imx_enable_cpu(cpu, false) call into .cpu_kill
hook, and leave the cpu to be hot-unplugged in WFI within .cpu_die,
so that we can get a more stable cpu hot-plug operation.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Framebuffer platform device is now identified by a device id (imx1-fb or
imx21-fb) instead of by driver name (imx-fb).
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Now that we have GIC moved to drivers/irqchip and all GIC DT init for
platforms using irqchip_init, move gic.h and update the remaining
includes.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Convert all GIC DT initialization over to use common irqchip_init
function.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Now that the GIC initialization sets up the handle_arch_irq pointer, we
can remove it for all machines and make it static.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>