This patch fix the CQ irq handler to work in hosts with BE architecture.
It adds the correct endian-swapping macros around the relevant memory
accesses.
Signed-off-by: Ben Segal <bpsegal20@gmail.com>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
This patch renames four functions in the ASIC-specific functions section,
so it will be easier to differentiate them from the generic kernel
functions with the same name.
This will help in future code reviews, to make sure we don't use the
kernel functions directly.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
The device's CPU accessible memory on host is managed in a dedicated
pool, except for 2 regions - Primary Queue (PQ) and Event Queue (EQ) -
which are allocated from generic DMA pools.
Due to address length limitations of the CPU, the addresses of all these
memory regions must have the same MSBs starting at bit 40.
This patch modifies the allocation of the PQ and EQ to be also from the
dedicated pool, to ensure compliance with the limitation.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Add __cpu_to_le16/32/64 and __le16/32/64_to_cpu where needed according to
sparse.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for doing various on-the-fly reset of Goya.
The driver supports two types of resets:
1. soft-reset
2. hard-reset
Soft-reset is done when the device detects a timeout of a command
submission that was given to the device. The soft-reset process only resets
the engines that are relevant for the submission of compute jobs, i.e. the
DMA channels, the TPCs and the MME. The purpose is to bring the device as
fast as possible to a working state.
Hard-reset is done in several cases:
1. After soft-reset is done but the device is not responding
2. When fatal errors occur inside the device, e.g. ECC error
3. When the driver is removed
Hard-reset performs a reset of the entire chip except for the PCI
controller and the PLLs. It is a much longer process then soft-reset but it
helps to recover the device without the need to reboot the Host.
After hard-reset, the driver will restore the max power attribute and in
case of manual power management, the frequencies that were set.
This patch also adds two entries to the sysfs, which allows the root user
to initiate a soft or hard reset.
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for receiving events from Goya's control CPU and
for receiving MSI-X interrupts from Goya's DMA engines and CPU.
Goya's PCI controller supports up to 8 MSI-X interrupts, which only 6 of
them are currently used. The first 5 interrupts are dedicated for Goya's
DMA engine queues. The 6th interrupt is dedicated for Goya's control CPU.
The DMA queue will signal its MSI-X entry upon each completion of a command
buffer that was placed on its primary queue. The driver will then mark that
CB as completed and free the related resources. It will also update the
command submission object which that CB belongs to.
There is a dedicated event queue (EQ) between the driver and Goya's control
CPU. The EQ is located on the Host memory. The control CPU writes a new
entry to the EQ for various reasons, such as ECC error, MMU page fault, Hot
temperature. After writing the new entry to the EQ, the control CPU will
trigger its dedicated MSI-X entry to signal the driver that there is a new
entry in the EQ. The driver will then read the entry and act accordingly.
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the H/W queues module and the code to initialize Goya's
various compute and DMA engines and their queues.
Goya has 5 DMA channels, 8 TPC engines and a single MME engine. For each
channel/engine, there is a H/W queue logic which is used to pass commands
from the user to the H/W. That logic is called QMAN.
There are two types of QMANs: external and internal. The DMA QMANs are
considered external while the TPC and MME QMANs are considered internal.
For each external queue there is a completion queue, which is located on
the Host memory.
The differences between external and internal QMANs are:
1. The location of the queue's memory. External QMANs are located on the
Host memory while internal QMANs are located on the on-chip memory.
2. The external QMAN write an entry to a completion queue and sends an
MSI-X interrupt upon completion of a command buffer that was given to
it. The internal QMAN doesn't do that.
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ben Segal