Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
The CCK TX setting when switch channel will fix the CCK to
path A only, so if the antenna is configured to path B
(e.g. iw phy set antenna 0x2 0x3 "TX B/RX AB"), then the CCK
packets can never be delivered to the air if only path B is
connected with an antenna (it can possibly be transmitted
through path A, but as path B is configured, the expected
behavior is incorrect).
This can also solve the racing issue of CCK TX setting between
driver and firmware. The CCK TX setting in driver should be
removed. Otherwise, the CCK TX setting would be wrong when the
racing occurs.
Fixes: 297bcf8222 ("rtw88: add support for set/get antennas")
Signed-off-by: Chien-Hsun Liao <ben.liao@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200522091234.24495-1-yhchuang@realtek.com
For older versions of gcc, the array = {0}; will cause warnings:
drivers/net/wireless/realtek/rtw88/rtw8822c.c: In function 'rtw8822c_power_trim':
>> drivers/net/wireless/realtek/rtw88/rtw8822c.c:1039:2: warning:
>> missing braces around initializer [-Wmissing-braces]
s8 bb_gain[2][8] = {0};
^
drivers/net/wireless/realtek/rtw88/rtw8822c.c:1039:2: warning: (near
initialization for 'bb_gain[0]') [-Wmissing-braces]
Fixes: 5ad4d8957b ("rtw88: set power trim according to efuse PG values")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200522035521.12295-1-yhchuang@realtek.com
Connecting to an AP with WPA2 security may fail. The IQK
and the EAPOL 4-way handshake may overlap because the
driver does IQK right after assoc success.
For 802.11n devices, the IQK is done in the driver and it
could require more than 100ms to complete. During IQK, any
TX/RX events are paused. So if the EAPOL 4-way handshake
started before IQK finished, then the 1/4 and 2/4 part of
the handshake could be dropped. The AP will then issue
deauth with reason IEEE8021X_FAILED (23).
To resolve this, move IQK routine into managed TX prepare
(ieee80211_ops::mgd_prepare_tx()). The callback is called
before the managed frames (auth/assoc) are sent. This will
make sure that the IQK is completed before the handshake
starts. But don't do IQK during scanning because doing it
on each channel will take too long.
For 802.11ac devices, the IQK is done in firmware and it
takes less time to complete. Therefore we don't see a
failure during the EAPOL 4-way handshake. But it is still
worth moving the IQK into ieee80211_ops::mgd_prepare_tx().
Fixes: f5df1a8b43 ("rtw88: 8723d: Add 8723DE to Kconfig and Makefile")
Tested-by: You-Sheng Yang <vicamo.yang@canonical.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200529025009.2468-4-yhchuang@realtek.com
Coex mechanism used to make BT have higher priority and more time to
transfer data when BT inquiry-page, which leads to poor WiFi performance.
Should take WiFi traffic into consideration. If the WiFi is having heavy
traffic, use another parameter to make sure WiFi has more chance to TX/RX,
while guarantee the priority of BT for inquiry. If the WiFi isn't busy
(connected or not), set proper parameter to fix originals.
Fixes: f5df1a8b43 ("rtw88: 8723d: Add 8723DE to Kconfig and Makefile")
Tested-by: You-Sheng Yang <vicamo.yang@canonical.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200529025009.2468-3-yhchuang@realtek.com
Without setting antenna control owner, the WiFi could be disconnected if
the BT has traffic. Because the antenna is switched to BT side for its
traffic, and the WiFi will have no chance to transfer data. Set control
owner to prevent WiFi disconnect issue.
Fixes: f5df1a8b43 ("rtw88: 8723d: Add 8723DE to Kconfig and Makefile")
Tested-by: You-Sheng Yang <vicamo.yang@canonical.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200529025009.2468-2-yhchuang@realtek.com
This reverts commit 07d0f55349.
For rtw88 driver, the SDIO is going to be supported, so there is
no need to remove the SDIO related power sequence settings. And
while the power sequence parser will pass in the mask of the HCI,
the SDIO part will not be used to set registers accordingly.
Moreover, the power sequence table is released as a whole package,
so the next time if we are going to update, the SDIO settings will
be overwritten. So, revert this now.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200520055350.23328-1-yhchuang@realtek.com
The for-loop seems to be redundant, the assignments for indexes
0..2 are being over-written by the last index 3 in the loop. Remove
the loop and use index 3 instead.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200515102226.29819-1-colin.king@canonical.com
Currently ldo_pwr has the LDO25 voltage bits set to zero and then
it is overwritten with the new voltage setting. The assignment
looks incorrect, it should be bit-wise or'ing in the new voltage
setting rather than a direct assignment.
Addresses-Coverity: ("Unused value")
Fixes: 1afb5eb7a0 ("rtw88: 8723d: Add cfg_ldo25 to control LDO25")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200514181329.16292-1-colin.king@canonical.com
Rename the name of the kernel module for rtw88's core and pci.
Add proper prefix 'rtw88_' to easily recognize them, also can
avoid confusion with other drivers. (ex. r8822be in staging)
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200515052327.31874-8-yhchuang@realtek.com
remove the unused about pci after extracting chip modules
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200515052327.31874-7-yhchuang@realtek.com
Make objects about 8723d functions and 8723d tables,
i.e. rtw8723d.o and rtw8723d_table.o, an individual
kernel module called rtw88_8723d.ko.
For 8723d pcie chip, i.e. 8723DE chip, add a chip
entry point module called rtw88_8723de.ko which
will depend on rtw88_8723d.ko and rtwpci.ko.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200515052327.31874-6-yhchuang@realtek.com
Make objects about 8822b functions and 8822b tables,
i.e. rtw8822b.o and rtw8822b_table.o, an individual
kernel module called rtw88_8822b.ko.
For 8822b pcie chip, i.e. 8822BE chip, add a chip
entry point module called rtw88_8822be.ko which
will depend on rtw88_8822b.ko and rtwpci.ko.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200515052327.31874-5-yhchuang@realtek.com
Make objects about 8822c functions and 8822c tables,
i.e. rtw8822c.o and rtw8822c_table.o, an individual
kernel module called rtw88_8822c.ko.
For 8822c pcie chip, i.e. 8822CE chip, add a chip
entry point module called rtw88_8822ce.ko which
will depend on rtw88_8822c.ko and rtwpci.ko.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200515052327.31874-4-yhchuang@realtek.com
In the current design, chip entry points are built into
the pci module. That makes the pci module depend on chips.
According to dependence, once the pci module is loaded,
kernel will load chip functionalities, including those that
may not be currently used.
We plan to split chip entry points from the pci module.
Thence we export pci symbols that will be used in chip
entry point modules.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200515052327.31874-3-yhchuang@realtek.com
In the current design, various chip functions and tables
are built into rtw88 core. That causes kernel to load its
functionalities even if a chip isn't currently used. We
plan to make each chip's functionalities a separate
kernel module to reduce rtw88 core. And kernel will be
able to load the necessary.
Before extracting chip functionalities, we export symbols
inside rtw88 core which will be used in chip modules.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200515052327.31874-2-yhchuang@realtek.com
Seven years ago we tried to fix a leak but actually introduced a double
free instead. It was an understandable mistake because the code was a
bit confusing and the free was done in the wrong place. The "skb"
pointer is freed in both _rtl_usb_tx_urb_setup() and _rtl_usb_transmit().
The free belongs _rtl_usb_transmit() instead of _rtl_usb_tx_urb_setup()
and I've cleaned the code up a bit to hopefully make it more clear.
Fixes: 36ef0b473f ("rtlwifi: usb: add missing freeing of skbuff")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200513093951.GD347693@mwanda
Fix the following warning:
drivers/net/wireless/realtek/rtl818x/rtl8187/rtl8225.c:609:17: warning:
‘rtl8225z2_tx_power_ofdm’ defined but not used
static const u8 rtl8225z2_tx_power_ofdm[] = {
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: ChenTao <chentao107@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200513011754.28432-1-chentao107@huawei.com
sparse warnings: (new ones prefixed by >>)
>> drivers/net/wireless/realtek/rtw88/rtw8723d.c:1899:6: sparse: sparse:
symbol 'rtw8723d_pwr_track' was not declared. Should it be static?
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200512103534.5889-1-yhchuang@realtek.com
8723D adds some experimental features to word 0x06 of cam entry, so fill
zeros to initialize them to off state. For existing chips, these two words
are reserved and always zeros, so this change is harmless for them.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200512102621.5148-9-yhchuang@realtek.com
8723D is a Wifi+BT combo card. To make them work properly, we need coex
mechanism to avoid interference, such as TX simultaneously. Basically,
coex.c provide main algorithm to deal with many use cases, and this commit
adds some parameters and ops differ from other chips, because coex
hardware and WiFi generation are changed.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200512102621.5148-8-yhchuang@realtek.com
Since 8723D use different address of ltecoex register, this commit add a
new field in chip_info and fill proper address. Then, ltecoex_read_reg()
and ltecoex_reg_write() can use them to access ltecoex according to chip.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200512102621.5148-7-yhchuang@realtek.com
Flush queue is used to check if queue is empty, before doing something
else. Since 8723D uses different registers and page number of
availabl/reserved occupy 8 bits instead of 16 bits, so use a 'wsize' field
to discriminate which rtw_read{8,16} is adopted.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200512102621.5148-6-yhchuang@realtek.com
Without this patch, wifi card can't initialize properly due to BT in USB
suspend state. So, we disable BT USB suspend (wakeup) in shutdown callback
that is the moment before rebooting. To save BT USB power, we can't do this
in 'remove' callback.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200512102621.5148-5-yhchuang@realtek.com
When chip's temperature is changed, RF characters are changed. To keep the
characters to be consistent, 8723d uses thermal meter to assist in
calibrating LCK, IQK, crystal and TX power.
A base thermal value is programmed in efuse, all calibration data in
MP process is based on this thermal value. So we calucate the delta of
thermal value between the base value, and use this delta to reference XTAL
and TX power offset tables to know how much we need to adjust.
For IQK and LCK, driver checks if delta of thermal value is over 8, then
they are triggered.
For crystal adjustment, when delta of thermal value is changed, we check
XTAL tables to get offset of XTAL value. If thermal value is larger than
base value, positive table (_p as suffix) is used. Otherwise, we use
negative table (_n as suffix). Then, we add offset to XTAL default value
programmed in efuse, and write sum value to register.
To compensate TX power, there are two hierarchical tables. First level use
delta of thermal value to access eight tables to yield delta of TX power
index. Then, plus base TX power index to get index of BB swing table
(second level tables) where register value is induced.
BB swing table can't deal with all cases, if index of BB swing table is
over the size of the table. In this case, TX AGC is used to compensate the
remnant part. Assume 'upper' is the upper bound of BB swing table, and
'target' is the desired index. Then, we can illustrate them as
compensation method BB swing TX AGC
------------------- -------- --------------
target > upper upper target - upper
target < 0 0 target
otherwise target 0
For debug purpose, add a column 'rem' to tx_pwr_tbl entry, and it looks
like
path rate pwr base (byr lmt ) rem
A CCK_1M 32(0x20) 34 -2 ( 0 -2) 0
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200512102621.5148-4-yhchuang@realtek.com
IQ calibration is used to calibrate RF characteristic to yield expected
performance. Basically, we do calibration twice and compare the similarity
to determine calibration is good or not, if not we do the third
calibration, and then compare with the results of first and second
calibration. If it still not similar, IQK is failed.
Before doing calibration, we need to backup registers that will be
modified in calibration procedure, and restore these registers after
calibration is done.
A calibration procedure can divided into four sub-procedures that are
S1-TX, S1-RX, S0-TX and S0-RX. Where, S1 and S0 represent to path A and B
respectively. Each sub-procedure configure proper registers, and then
rigger one-shot calibration and poll until completion. For RX calibration,
it needs to do twice one-shot calibration, first one is to yield parameter
used by second one.
The result of TX part is stored for TX power tracking that adjusts TX AGC
to output expected power.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200512102621.5148-3-yhchuang@realtek.com
LC calibration is done by hardware circuit. Driver sets the LCK bit to kick
start, and then poll the bit to check if it's done.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200512102621.5148-2-yhchuang@realtek.com
First set of patches for v5.8. Changes all over, ath10k apparently
seeing most new features this time. rtw88 also had lots of changes due
to preparation for new hardware support.
In this pull request there's also a new macro to include/linux/iopoll:
read_poll_timeout_atomic(). This is needed by rtw88 for atomic
polling.
Major changes:
ath11k
* add debugfs file for testing ADDBA and DELBA
* add 802.11 encapsulation offload on hardware support
* add htt_peer_stats_reset debugfs file
ath10k
* enable VHT160 and VHT80+80 modes
* enable radar detection in secondary segment
* sdio: disable TX complete indication to improve throughput
* sdio: decrease power consumption
* sdio: add HTT TX bundle support to increase throughput
* sdio: add rx bitrate reporting
ath9k
* improvements to AR9002 calibration logic
carl9170
* remove buggy P2P_GO support
p54usb
* add support for AirVasT USB stick
rtw88
* add support for antenna configuration
ti wlcore
* add support for AES_CMAC cipher
iwlwifi
* support for a few new FW API versions
* new hw configs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJetAhAAAoJEG4XJFUm622bADEH/A1OjAD3H1iZyTmXHP4T7yZe
TKJ+9I6B3BDR1czUTm+kUhrgBDNpdLLtu+b+5QXfpPLrtZ0FF/zjuazgueyqQpZ1
zudj+rG72njHpU0RKtO7wIBrCtckLPV0be+3026hztatJmJ7XQ9FvsanFPPsrrNv
0lh8E8kDUSynOW2me8FW1GBgDkGaBaicAs4FSjwNJC31Wo/VN5m9gEFkGpT1VJWP
l0xeEQ/N2mknQVuTR4CuMT9VJ0SNlJrLZpBVAqkmc170c3pKChl3LTNCnP925ye9
Nfqw2sQKgUPJKRbZR5wZTphGuu4krFv0ldWCvb0oFtZlCLIkiOz6+AA7b33oV2A=
=7ewK
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-05-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.8
First set of patches for v5.8. Changes all over, ath10k apparently
seeing most new features this time. rtw88 also had lots of changes due
to preparation for new hardware support.
In this pull request there's also a new macro to include/linux/iopoll:
read_poll_timeout_atomic(). This is needed by rtw88 for atomic
polling.
Major changes:
ath11k
* add debugfs file for testing ADDBA and DELBA
* add 802.11 encapsulation offload on hardware support
* add htt_peer_stats_reset debugfs file
ath10k
* enable VHT160 and VHT80+80 modes
* enable radar detection in secondary segment
* sdio: disable TX complete indication to improve throughput
* sdio: decrease power consumption
* sdio: add HTT TX bundle support to increase throughput
* sdio: add rx bitrate reporting
ath9k
* improvements to AR9002 calibration logic
carl9170
* remove buggy P2P_GO support
p54usb
* add support for AirVasT USB stick
rtw88
* add support for antenna configuration
ti wlcore
* add support for AES_CMAC cipher
iwlwifi
* support for a few new FW API versions
* new hw configs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following coccicheck warning:
drivers/net/wireless/realtek/rtlwifi/rtl8188ee/rf.c:476:6-14: WARNING:
Comparison to bool
drivers/net/wireless/realtek/rtlwifi/rtl8188ee/rf.c:54:5-22: WARNING:
Comparison to bool
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504113321.41118-1-yanaijie@huawei.com
The variable 'rtlpriv->rfkill.rfkill_state' is bool and can directly
assigned to bool values.
Fix the following coccicheck warning:
drivers/net/wireless/realtek/rtlwifi/core.c:1725:14-42: WARNING:
Comparison of 0/1 to bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200429140924.7750-1-yanaijie@huawei.com
the related system resources were not released when pci_iomap() return
error in the rtw_pci_io_mapping() function. add pci_release_regions() to
fix it.
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Acked-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504083442.3033-1-zhengdejin5@gmail.com
Interface configuration table is used to configure PCI PHY that are
normally decided by design or bootstrap pin, and driver can do additional
settings by this table.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504105010.10780-9-yhchuang@realtek.com
DIG sets only one IG register for most chips, but 8723D need to set
additional register for CCK rate.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504105010.10780-8-yhchuang@realtek.com
This ops is used to do statistics of false alarm periodically, and then
fine tune RX initial gain to adaptive different circumstance.
There are three steps, hold/get/reset counter, to retrieve false alarm
counters that consist of CCK and OFDM. In addition to false alarm
counters, it also collects CRC ok/error counters of CCK, OFDM and HT.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504105010.10780-7-yhchuang@realtek.com
Some chips are not able to receive LDPC packets. Add an attribute
to rtw_chip_info to determine if the LDPC capability in [ht/vht]_cap
should be advertised or not.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504105010.10780-6-yhchuang@realtek.com
TX status report of 8723D differs from 8822B/8822C, it uses
C2H_CCX_TX_RPT (0x03) with different format. With sequence number
and TX status, driver can know if certain packet was transmitted
successfully.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504105010.10780-5-yhchuang@realtek.com
Set MAC/BB/RF register according to specified channel. The function
rtw_set_channel_mac() is used to set MAC registers, but 8723D only need
some of them.
For channel 14, we need to set different CCK DFIR values, so restore the
values when channel 1 to 13 is selected.
Spur calibration is needed in channel 13 and 14, and we do notch if spur
is over threshold.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504105010.10780-4-yhchuang@realtek.com
This ops is used to parse RX descriptor to know the length of received
packet and containing PHY status. If PHY status is existing, the order is
RX descriptor, PHY status and then packet.
There are two types of PHY status, named CCK and OFDM. Their size are the
same, but formats are different.
struct ieee80211_rx_status is also filled depends on above information.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504105010.10780-3-yhchuang@realtek.com
To improve user experience in field, we need DIG to adjust RX initial gain
depends on field situation. Since each chip has its own register address,
this commit defines 8723d specific address.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504105010.10780-2-yhchuang@realtek.com
The 'blocked' is a bool variable, and '==' expression itself is bool
too. So no need to convert it to 0/1.
This fixes the following coccicheck warning:
drivers/net/wireless/realtek/rtlwifi/base.c:508:13-41: WARNING:
Comparison of 0/1 to bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200426094115.23294-1-yanaijie@huawei.com
It's incorrect to use usleep in atomic context.
Switch to a macro which uses udelay instead of usleep to prevent the issue.
Fixes: 6343a6d4b2 ("rtw88: Add delay on polling h2c command status bit")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200423073007.3566-1-kai.heng.feng@canonical.com
There are spelling mistakes in two rtw_err error messages. Fix them.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424084733.7716-1-colin.king@canonical.com
Update RTL8822C devices' phy tables to v50.
The new parameters introduces new RFE type 5 for some new modules.
Also added a new regulatory CN for power limit.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424073812.26896-1-yhchuang@realtek.com
sparse warnings: (new ones prefixed by >>)
>> drivers/net/wireless/realtek/rtw88/mac.c:653:5: sparse: sparse:
symbol '__rtw_download_firmware' was not declared. Should it be static?
>> drivers/net/wireless/realtek/rtw88/mac.c:817:5: sparse: sparse:
symbol '__rtw_download_firmware_legacy' was not declared. Should it be
static?
Fixes: 15d2fcc6b2 ("rtw88: add legacy firmware download for 8723D devices")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424101255.28239-1-yhchuang@realtek.com
When fixing the initialization race, we neglected to account for
the fact that debugfs is initialized in wiphy_register(), and
some debugfs things went missing (or rather were rerooted to the
global debugfs root).
Fix this by adding debugfs entries only after wiphy_register().
This requires some changes in the rate control code since it
currently adds debugfs at alloc time, which can no longer be
done after the reordering.
Reported-by: Jouni Malinen <j@w1.fi>
Reported-by: kernel test robot <rong.a.chen@intel.com>
Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Reported-by: Felix Fietkau <nbd@nbd.name>
Cc: stable@vger.kernel.org
Fixes: 52e04b4ce5 ("mac80211: fix race in ieee80211_register_hw()")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/20200423111344.0e00d3346f12.Iadc76a03a55093d94391fc672e996a458702875d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement rtw_chip_ops::phy_set_param and ::mac_init to initialize
mac/bb/rf, and they are used during interface up. The procedure contains
power on sequence registers, download firmware, load predefined parameters,
mac/bb/rf specific register and etc.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200422034607.28747-9-yhchuang@realtek.com
TX FIFO size is 32k and it was divided into 256 pages with 128 bytes.
A boundary is used to split pages into two parts, head part is used to
store TX packets coming from host, and tail part is reserved for special
purposes, such as beacon packet, null data packet and so on.
The TX packets coming from host have many categories, such as VO, VI, BE,
BK, MG and etc. When going into head part of TX FIFO, they are classified
to four priority queue named low, normal, high and extra priority queues.
Each priority queue occupies predefined number of page, if a certain
priority queue is full, TX packet will store into PUB priority queue.
Similarly, RX FIFO is 16k and split into two parts, head part is used to
store RX packets, and tail part is 128 bytes and used to store report.
Thus, we fill this boundary to register as well.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200422034607.28747-8-yhchuang@realtek.com
The txagc table is used to map rate_id and txagc register address and
mask, and ops set_tx_power_index uses this table to write TX power to
corresponding registers. Since 8723D is a 1x1 2.4G 11n chip, only CCK, OFDM
and HT_MCS 0-7 are listed in the table.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200422034607.28747-7-yhchuang@realtek.com
Masahiro Yamada