The bamboo dts has a bug: it uses a non-naturally aligned range
for PCI memory space. This isnt' supported by the code, thus
causing PCI to break on this system.
This is due to the fact that while the chip memory map has 1G
reserved for PCI memory, it's only 512M aligned. The code doesn't
know how to split that into 2 different PMMs and fails, so limit
the region to 512M.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a IRQ init routine for the Nemo board which inits and attatches
the i8259 found in the SB600, and a cascade routine to dispatch the
interrupts.
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add routines for Nemo specific devices to init at boot time, these
being board level power-off and SB600's rtc.
Also add a run time variable to prevent these being activated
if we boot on a reference board.
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a IRQ init routine for the Nemo board which inits and attatches
the i8259 found in the SB600, and a cascade routine to dispatch the
interrupts.
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The A-Eon Amigaone X1000's Nemo motherboard has an AMD SB600
connected to one of the PCI-e root ports on its PaSemi
Pwrficient 1628M SoC. Normally the SB600 southbridge would be
connected to a hidden PCI-e port on the system's northbridge,
and as a result doesn't fully comply with the PCI-e spec.
Add code to relax the PCI-e detection in both the root port
and the Linux kernel allowing on board devices to be detected.
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As several other arches including x86, this patch makes it explicit
that a bad page fault is a NULL pointer dereference when the fault
address is lower than PAGE_SIZE
In the mean time, this page makes all bad_page_fault() messages
shorter so that they remain on one single line. And it prefixes them
by "BUG: " so that they get easily grepped.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Avoid pr_cont()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Combine the SYSCALL_EMU and SYSCALL_TRACE handling so that we only
call tracehook_report_syscall_entry() in one place.
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
[mpe: Flesh out change log, s/cached_flags/flags/, reflow comments]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Powerpc has somewhat odd usage where ZONE_DMA is used for all memory on
common 64-bit configfs, and ZONE_DMA32 is used for 31-bit schemes.
Move to a scheme closer to what other architectures use (and I dare to
say the intent of the system):
- ZONE_DMA: optionally for memory < 31-bit (64-bit embedded only)
- ZONE_NORMAL: everything addressable by the kernel
- ZONE_HIGHMEM: memory > 32-bit for 32-bit kernels
Also provide information on how ZONE_DMA is used by defining
ARCH_ZONE_DMA_BITS.
Contains various fixes from Benjamin Herrenschmidt.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The implemementation for the CONFIG_NOT_COHERENT_CACHE case doesn't share
any code with the one for systems with coherent caches. Split it off
and merge it with the helpers in dma-noncoherent.c that have no other
callers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The unmap methods need to transfer memory ownership back from the
device to the cpu by identical means as dma_sync_*_to_cpu. I'm not
sure powerpc needs to do any work in this transfer direction, but
given that it does invalidate the caches in dma_sync_*_to_cpu already
we should make sure we also do so on unmapping.
Signed-off-by: Christoph Hellwig <hch@lst.de>
[mpe: s/dir/direction in dma_nommu_unmap_page()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
AMIGAONE selects NOT_COHERENT_CACHE, so we better allow it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch fixes early DEBUG messages in prom.c:
- Use %px instead of %p to see the addresses
- Cast memblock_phys_mem_size() with (unsigned long long) to
avoid build failure when phys_addr_t is not 64 bits.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When building for ppc32 with clang these flags are unsupported:
-ffixed-r2 and -mmultiple
llvm's lib/Target/PowerPC/PPCRegisterInfo.cpp marks r2 as reserved on
when building for SVR4ABI and !ppc64:
// The SVR4 ABI reserves r2 and r13
if (Subtarget.isSVR4ABI()) {
// We only reserve r2 if we need to use the TOC pointer. If we have no
// explicit uses of the TOC pointer (meaning we're a leaf function with
// no constant-pool loads, etc.) and we have no potential uses inside an
// inline asm block, then we can treat r2 has an ordinary callee-saved
// register.
const PPCFunctionInfo *FuncInfo = MF.getInfo<PPCFunctionInfo>();
if (!TM.isPPC64() || FuncInfo->usesTOCBasePtr() || MF.hasInlineAsm())
markSuperRegs(Reserved, PPC::R2); // System-reserved register
markSuperRegs(Reserved, PPC::R13); // Small Data Area pointer register
}
This means we can safely omit -ffixed-r2 when building for 32-bit
targets.
The -mmultiple/-mno-multiple flags are not supported by clang, so
platforms that might support multiple miss out on using multiple word
instructions.
We wrap these flags in cc-option so that when Clang gains support the
kernel will be able use these flags.
Clang 8 can then build a ppc44x_defconfig which boots in Qemu:
make CC=clang-8 ARCH=powerpc CROSS_COMPILE=powerpc-linux-gnu- ppc44x_defconfig
./scripts/config -e CONFIG_DEVTMPFS -d DEVTMPFS_MOUNT
make CC=clang-8 ARCH=powerpc CROSS_COMPILE=powerpc-linux-gnu-
qemu-system-ppc -M bamboo \
-kernel arch/powerpc/boot/zImage \
-dtb arch/powerpc/boot/dts/bamboo.dtb \
-initrd ~/ppc32-440-rootfs.cpio \
-nographic -serial stdio -monitor pty -append "console=ttyS0"
Link: https://github.com/ClangBuiltLinux/linux/issues/261
Link: https://bugs.llvm.org/show_bug.cgi?id=39556
Link: https://bugs.llvm.org/show_bug.cgi?id=39555
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove PM_L2_ST_MISS and PM_L2_ST from HW cache event array since
these are bus events. And these needs to be programmed in groups.
Hence remove them.
Fixes: f1fb60bfde ('powerpc/perf: Export Power9 generic and cache events to sysfs')
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In previous generation processors, both bus events and direct
events of performance monitoring unit can be individually
programmabled and monitored in PMCs.
But in Power9, L2/L3 bus events are always available as a
"bank" of 4 events. To obtain the counts for any of the
l2/l3 bus events in a given bank, the user will have to
program PMC4 with corresponding l2/l3 bus event for that
bank.
Patch enforce two contraints incase of L2/L3 bus events.
1)Any L2/L3 event when programmed is also expected to program corresponding
PMC4 event from that group.
2)PMC4 event should always been programmed first due to group constraint
logic limitation
For ex. consider these L3 bus events
PM_L3_PF_ON_CHIP_MEM (0x460A0),
PM_L3_PF_MISS_L3 (0x160A0),
PM_L3_CO_MEM (0x260A0),
PM_L3_PF_ON_CHIP_CACHE (0x360A0),
1) This is an INVALID group for L3 Bus event monitoring,
since it is missing PMC4 event.
perf stat -e "{r160A0,r260A0,r360A0}" < >
And this is a VALID group for L3 Bus events:
perf stat -e "{r460A0,r160A0,r260A0,r360A0}" < >
2) This is an INVALID group for L3 Bus event monitoring,
since it is missing PMC4 event.
perf stat -e "{r260A0,r360A0}" < >
And this is a VALID group for L3 Bus events:
perf stat -e "{r460A0,r260A0,r360A0}" < >
3) This is an INVALID group for L3 Bus event monitoring,
since it is missing PMC4 event.
perf stat -e "{r360A0}" < >
And this is a VALID group for L3 Bus events:
perf stat -e "{r460A0,r360A0}" < >
Patch here implements group constraint logic suggested by Michael Ellerman.
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Raw event code has couple of fields "unit" and "cache" in it, to capture
the "unit" to monitor for a given pmcxsel and cache reload qualifier to
program in MMCR1.
isa207_get_constraint() refers "unit" field to update the MMCRC (L2/L3)
Event bus control fields with "cache" bits of the raw event code.
These are power8 specific and not supported by PowerISA v3.0 pmu. So wrap
the checks to be power8 specific. Also, "cache" bit field is referred to
update MMCR1[16:17] and this check can be power8 specific.
Fixes: 7ffd948fae ('powerpc/perf: factor out power8 pmu functions')
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Update the raw event code comment in power9-pmu.c with respect to
"cache" bits, since power9 MMCRC does not support these.
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On each sample, Sample Instruction Event Register (SIER) content
is saved in pt_regs. SIER does not have a entry as-is in the pt_regs
but instead, SIER content is saved in the "dar" register of pt_regs.
Patch adds another entry to the perf_regs structure to include the "SIER"
printing which internally maps to the "dar" of pt_regs.
It also check for the SIER availability in the platform and present
value accordingly
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
MMCRA[34:36] and MMCRA[38:44] expose the thresholding counter value.
Thresholding counter can be used to count latency cycles such as
load miss to reload. But threshold counter value is not relevant
when the sampled instruction type is unknown or reserved. Patch to
fix the thresholding counter value to zero when sampled instruction
type is unknown or reserved.
Fixes: 170a315f41c6('powerpc/perf: Support to export MMCRA[TEC*] field to userspace')
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit 2865d08dd9 ("powerpc/mm: Move the DSISR_PROTFAULT sanity
check") we moved the protection fault access check before the vma
lookup. That means we hit that WARN_ON when user space accesses a
kernel address. Before that commit this was handled by find_vma() not
finding vma for the kernel address and considering that access as bad
area access.
Avoid the confusing WARN_ON and convert that to a ratelimited printk.
With the patch we now get:
for load:
a.out[5997]: User access of kernel address (c00000000000dea0) - exploit attempt? (uid: 1000)
a.out[5997]: segfault (11) at c00000000000dea0 nip 1317c0798 lr 7fff80d6441c code 1 in a.out[1317c0000+10000]
a.out[5997]: code: 60000000 60420000 3c4c0002 38427790 4bffff20 3c4c0002 38427784 fbe1fff8
a.out[5997]: code: f821ffc1 7c3f0b78 60000000 e9228030 <89290000> 993f002f 60000000 383f0040
for exec:
a.out[6067]: User access of kernel address (c00000000000dea0) - exploit attempt? (uid: 1000)
a.out[6067]: segfault (11) at c00000000000dea0 nip c00000000000dea0 lr 129d507b0 code 1
a.out[6067]: Bad NIP, not dumping instructions.
Fixes: 2865d08dd9 ("powerpc/mm: Move the DSISR_PROTFAULT sanity check")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Tested-by: Breno Leitao <leitao@debian.org>
[mpe: Don't split printk() string across lines]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The 603 doesn't have a HASH table, TLB misses are handled by
software. It is then possible to generate page fault when
_PAGE_EXEC is not set like in nohash/32.
There is one "reserved" PTE bit available, this patch uses
it for _PAGE_EXEC.
In order to support it, set_pte_filter() and
set_access_flags_filter() are made common, and the handling
is made dependent on MMU_FTR_HPTE_TABLE
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Define slice_init_new_context_exec() at all time to avoid
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With the following piece of code, the following compilation warning
is encountered:
if (_IOC_DIR(ioc) != _IOC_NONE) {
int verify = _IOC_DIR(ioc) & _IOC_READ ? VERIFY_WRITE : VERIFY_READ;
if (!access_ok(verify, ioarg, _IOC_SIZE(ioc))) {
drivers/platform/test/dev.c: In function 'my_ioctl':
drivers/platform/test/dev.c:219:7: warning: unused variable 'verify' [-Wunused-variable]
int verify = _IOC_DIR(ioc) & _IOC_READ ? VERIFY_WRITE : VERIFY_READ;
This patch fixes it by referencing 'type' in the macro allthough
doing nothing with it.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
commit f21f49ea63 ("[POWERPC] Remove the dregs of APUS support from
arch/powerpc") removed CONFIG_APUS, but forgot to remove the logic
which adapts tophys() and tovirt() for it.
This patch removes the last stale pieces.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch fixes the loop in p_block_mapped() and v_block_mapped()
to scan the entire bat_addrs[] array.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Depending on the CONFIG selected, many of the MMU features are
not possible. Lets only get the possible ones in MMU_FTRS_POSSIBLE.
This allows gcc to get rid at compile time of code related to
not possible features.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use patch sites and associated helpers to manage TLB handlers
patching instead of hardcoding.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Instead of hardcoding the TLB handlers patching, use
the newly created modify_instruction_site() helper.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use patch_sites and the new modify_instruction_site() function
instead of hardcoding hash functions patching.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Instead of manually patching a blr at hash_page() entry in
MMU_init_hw(), this patch adds a features section in head_32.S
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use patch_site_addr() instead of hardcoding the
address calculation in machine_init()
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add two helpers to avoid hardcoding of instructions modifications.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Using patch_site_addr() helper, patch_instruction_site() and
patch_branch_site() can be simplified and inlined.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In file included from ./include/linux/hugetlb.h:445:0,
from arch/powerpc/kernel/setup-common.c:37:
./arch/powerpc/include/asm/hugetlb.h: In function ‘huge_ptep_clear_flush’:
./arch/powerpc/include/asm/hugetlb.h:154:8: error: variable ‘pte’ set but not used [-Werror=unused-but-set-variable]
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The code:
ifdef CONFIG_6xx
KBUILD_CFLAGS += -mcpu=powerpc
endif
was added in 2006 in commit f48b8296b3 ("[PATCH] powerpc32: Set cpu
explicitly in kernel compiles"). This change was acceptable since the
TARGET_CPU logic was 64-bit only.
Since commit 0e00a8c9fd ("powerpc: Allow CPU selection
also on PPC32") this logic is no longer acceptable after the TARGET_CPU
specific. It currently appends -mcpu=powerpc at the end of the command
line, after any TARGET_CPU specific:
gcc -Wp,-MD,init/.do_mounts.o.d ...
-mcpu=powerpc -mbig-endian -m32 ...
-mcpu=e300c2 ...
-mcpu=powerpc ...
../init/do_mounts.c
Fixes: 0e00a8c9fd ("powerpc: Allow CPU selection also on PPC32")
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
ipic_set_priority() has been unused since 2006 when the last usage was
removed in commit b9f0f1bb2b ("[POWERPC] Adapt ipic driver to new
host_ops interface, add set_irq_type to set IRQ sense").
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Merge our fixes branch again, this has a couple of build fixes and also
a change to do_syscall_trace_enter() that will conflict with a patch we
want to apply in next.
Arch code should use tracehook_*() helpers, as documented in
include/linux/tracehook.h, ptrace_report_syscall() is not expected to
be used outside that file.
The patch does not look very nice, but at least it is correct
and opens the way for PTRACE_GET_SYSCALL_INFO API.
Co-authored-by: Dmitry V. Levin <ldv@altlinux.org>
Fixes: 5521eb4bca ("powerpc/ptrace: Add support for PTRACE_SYSEMU")
Signed-off-by: Elvira Khabirova <lineprinter@altlinux.org>
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
[mpe: Take this as a minimal fix for 4.20, we'll rework it later]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The "altmap" is used to provide a pool of memory that is reserved for
the vmemmap backing of hot-plugged memory. This is useful when adding
large amount of ZONE_DEVICE memory to a system with a limited amount of
normal memory.
On ppc64 we use huge pages to map the vmemmap which requires the backing
storage to be contigious and aligned to the hugepage size. The altmap
implementation allows for the altmap provider to reserve a few PFNs at
the start of the range for it's own uses and when this occurs the
first chunk of the altmap is not usable for hugepage mappings. On hash
there is no sane way to fall back to a normal sized page mapping so we
fail the allocation. This results in memory hotplug failing with
ENOMEM when the new range doesn't fall into an existing vmemmap block.
This patch handles this case by falling back to using system memory
rather than failing if we cannot allocate from the altmap. This
fallback should only ever be used for the first vmemmap block so it
should not cause excess memory consumption.
Fixes: 7b73d978a5 ("mm: pass the vmem_altmap to vmemmap_populate")
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The interleave set cookie is used to determine if a label stored in the
metadata space should be applied to the current region. This is
important in the case of NVDIMMs since the firmware may change the
interleaving configuration of a DIMM which would invalidate the existing
labels. In our case the hypervisor hides those details from us so we
don't really care, but libnvdimm still requires the interleave set
cookie to be non-zero.
For our purposes we just need the set cookie to be unique and fixed for
a given PAPR SCM region and using the unit-guid (really a UUID) is fine
for this purpose.
Fixes: b5beae5e22 ("powerpc/pseries: Add driver for PAPR SCM regions")
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
[mpe: Use kernel types (u64)]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When a new nvdimm device is registered with libnvdimm via
nvdimm_create() it is added as a device on the nvdimm bus. The probe
function for the DIMM driver is potentially quite slow so actually
registering and probing the device is done in an async domain rather
than immediately after device creation. This can result in a race where
the region device (created 2nd) is probed first and fails to activate at
boot.
To fix this we use the same approach as the ACPI/NFIT driver which is to
check that all the DIMM devices registered successfully. LibNVDIMM
provides the nvdimm_bus_count_dimms() function which synchronises with
the async domain and verifies that the dimm was successfully registered
with the bus.
If either of these does not occur then we bail.
Fixes: b5beae5e22 ("powerpc/pseries: Add driver for PAPR SCM regions")
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The return values of a h-call are returned in the CPU registers and
written to the provided buffer by the plpar_hcall() wrapper. As a result
the values written to memory are always in the native endian and should
not be byte swapped.
The inital implementation of the H-Call interface was done in qemu and
the returned values were byte swapped unnecessarily in both the
hypervisor and in the driver so this was only noticed when bringing up
the PowerVM implementation.
Fixes: b5beae5e22 ("powerpc/pseries: Add driver for PAPR SCM regions")
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Benjamin Herrenschmidt