DMA can only be done from physical addresses; move the "virt_to_phys"
source/destination buffer address translation from the dbdma queueing
functions (since the hardware can only DMA to/from physical addresses)
to their respective users.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove dbdma compat macros, move remaining users over to default
queueing functions and -flags.
(Queueing function signature has changed in order to give
a build failure instead of silent functional changes due
to the no longer implicitly specified DDMA_FLAGS_IE flag)
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6: (31 commits)
spi: Correct SPI clock frequency setting in spi_mpc8xxx
spi/spi_s3c64xx.c: Fix continuation line formats
spi/dw_spi: Fix dw_spi_mmio to depend on HAVE_CLK
spi/dw_spi: Allow dw_spi.c to be a module
spi/dw_spi: mmio code style fixups
Memory-mapped dw_spi driver
spi/dw_spi: fix missing export of dw_spi_remove_host
spi/dw_spi: conditional transfer mode changes
spi/dw_spi: remove conditional from 'poll_transfer'.
spi/dw_spi: fixed a spelling typo in a warning message.
spi/dw_spi: add return value to empty mrst_spi_debugfs_init()
spi/dw_spi: enable platform specific chipselect.
spi/dw_spi: add a FIFO depth detection
spi/dw_spi: fix __init/__devinit section mismatch
spi: xilinx_spi: Fix up I/O routine wrapping bogosity.
spi/spi_imx: add device information by switching pr_debug() to dev_dbg()
spi: update MSIOF includes
spi/dw_spi: refine the IRQ mode working flow
spi/dw_spi: add a missed dw_spi_remove_host() in exit sequence
spi/dw_spi: bug fix in wait_till_not_busy()
...
Correct SPI clock frequency division factor rounding, preventing clock rates
higher than the maximum specified clock frequency being used.
When specifying spi-max-frequency = <10000000> in the device tree,
the resulting frequency was 11.1 MHz, with spibrg being 133333332.
According to the freescale data sheet [1], the spi clock rate is
spiclk = spibrg / (4 * (pm+1))
The existing code calculated
pm = mpc8xxx_spi->spibrg / (hz * 4); pm--;
resulting in pm = (int) (3.3333) - 1 = 2,
resulting in spiclk = 133333332/(4*(2+1)) = 11111111
With the fix,
pm = (mpc8xxx_spi->spibrg - 1) / (hz * 4) + 1; pm--;
resulting in pm = (int) (4.3333) - 1 = 3,
resulting in spiclk = 133333332/(4*(3+1)) = 8333333
Without the fix, for every desired SPI frequency that
is not exactly derivable from spibrg, pm will be too
small due to rounding down, resulting in a too high SPI clock,
so we need a pm which is one higher.
For values that are exactly derivable, spibrg will
be dividable by (hz*4) without remainder, and
(int) ((spibrg-1)/(hz*4)) will be one lower than
(int) (spibrg)/(hz*4), which is compensated by adding 1.
For these values, the fixed version calculates the same pm
as the unfixed version.
For all values that are not exactly derivable,
spibrg will be not dividable by (hz*4) without
remainder, and (int) ((spibrg-1)/(hz*4)) will be
the same as (int) (spibrg)/(hz*4), and the calculated pm will
be one higher than calculated by the unfixed version.
References:
[1] http://www.freescale.com/files/32bit/doc/ref_manual/MPC8315ERM.pdf,
page 22-10 -> 1398
Signed-off-by: Ernst Schwab <eschwab@online.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
String constants that are continued on subsequent lines with \
are not good.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The spi_sh_msiof.c driver presently misconfigures REDG and TEDG. TEDG==0
outputs data at the **rising edge** of the clock and REDG==0 samples data
at the **falling edge** of the clock. Therefore for SPI, TEDG must be
equal to REDG, otherwise the last byte received is not sampled in SPI
mode 3.
This brings the driver in line with the SH7723 HW Reference Manual
settings documented in Figures 20.20 and 20.21 ("SPI Clock and data
timing").
Signed-off-by: Markus Pietrek <Markus.Pietrek@emtrion.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
dw_spi_mmio is dependent on the clock framework. This marks it as such
in Kconfig.
Signed-off-by: Jean-Hugues Deschenes <jean-hugues.deschenes@octasic.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Minor code style cleanups following comments by Wolfram Sang
Signed-off-by: Jean-Hugues Deschenes <jean-hugues.deschenes@octasic.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
So that interface drivers could be built as modules
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This allows the switching between transfer modes between 'transmit only',
'receive only' and 'transmit and receive' modes. Due to the design of the SPI
block, changing transfer modes requires that the block be disabled; in doing
so the chipselect line is inherently deasserted and (usually) the attached
device discards its state. Consequentially, switching modes requires that a
platform-specific chipselect function has been defined so that the chipselect
is not dropped during the change.
Signed-off-by: George Shore <george@georgeshore.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The 'poll_transfer' function employs a conditional to test whether the
transmit buffer is valid; in doing so, on a receive operation no data is
clocked out, thus no data is clocked in and ultimately errors appear.
This removes the conditional as the transmit function will be set to a null
writer when the transmit buffer is invalid, allowing the driver to clock
0x00 out to the device to receive data from the device.
Signed-off-by: George Shore <george@georgeshore.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
FIFO depth is configurable for each implementation of DW core,
so add a depth detection for those interface drivers who don't set
the fifo_len explicitly
Signed-off-by: Feng Tang <feng.tang@intel.com>
Acked-by: Jean-Hugues Deschenes <jean-hugues.deschenes@octasic.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
xilinx_spi presently makes some fairly questionable assumptions about I/O
routines, and attempts to assign ioread32/iowrite32 and friends directly
to its own internal function pointers. On many platforms these I/O
routines are macros or wrappers and not actual functions on their own,
resulting in things like:
ERROR: "ioread32be" [drivers/spi/xilinx_spi.ko] undefined!
ERROR: "iowrite32be" [drivers/spi/xilinx_spi.ko] undefined!
ERROR: "iowrite32" [drivers/spi/xilinx_spi.ko] undefined!
ERROR: "ioread32" [drivers/spi/xilinx_spi.ko] undefined!
If xilinx_spi wants to do this sort of casting, it needs to provide its
own wrappers for these, or change how it does accesses completely.
I've opted for the first approach, and the attached silly patch does
that. If someone with the hardware available wants to give the second
option a try that's ok too. In any event, the current code is broken for
at least: arm, avr32, blackfin, microblaze, mn10300, and sh.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Update the MSIOF driver to remove the architecture
speficic spi header file and add err.h. This makes
the driver compile on non-SH architectures.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Now dw_spi core fully supports 3 transfer modes: pure polling,
DMA and IRQ mode. IRQ mode will use the FIFO half empty as
the IRQ trigger, so each interface driver need set the fifo_len,
so that core driver can handle it properly
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Make the driver wait at least for 1 jiffie before issuing the
warning, no matter what HZ is set to
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Since most of the chip-selects are simply going to be like
gpio_set_value, it would do good to have the same callback type
so that it could simply be made to point at gpio_set_value.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Header for platform specific stuff has been rename to include the SoC
type. Include the new header instead.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The pointer to SPI rate source clock had better be the member of
driver local data structure rather than platform specific.
Also, remove definitions of variable 'sci' that are rendered
useless as a consequence.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The instance of SPI clock for controller and that used for generating
signals ought to be independently handled.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
platform_get_irq returns -ENXIO on failure, so !irq was probably
always true. Make irq a signed variable and compare irq <= 0. Note
that a return value of zero is still handled as error even though this
could mean irq0.
This is a followup to 305b3228f9 that
changed the return value of platform_get_irq from 0 to -ENXIO on error.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add support for the QSPI controller found some on Freescale/Motorola
Coldfire MCUs.
Full duplex, active high cs, spi modes 0-3 and word sizes 8-16 bits are
supported. The hardware drives the MISO, MOSI and SCLK lines, but the chip
selects are managed via GPIO and must be configured by the board code.
The QSPI controller has an 80 byte buffer which allows us to transfer up to 16
words at a time. For transfers longer than 16 words, we split the buffer in
half so we can update in one half while the controller is operating on the
other half. Interrupt latencies then ultimately limits our sustained thru-put
to something less than half the maximum speed supported by the part.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The match_table field of the struct of_device_id is constant
in <linux/of_platform.h> so it is worth to make the initialization
data constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Márton Németh <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds support for a SPI master driver for the
DaVinci series of SOCs
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Philby John <pjohn@in.mvista.com>
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6:
spi: spi_txx9.c: use resource_size()
spi: spi_sh_sci.c: use resource_size()
spi: spi_mpc8xxx.c: use resource_size()
spi: spi_bfin5xx.c: use resource_size()
spi: atmel_spi.c: use resource_size()
spi: Add s3c64xx SPI Controller driver
atmel_spi: fix dma addr calculation for len > BUFFER_SIZE
spi_s3c24xx: add FIQ pseudo-DMA support
spi: controller driver for Designware SPI core
spidev: add proper section markers
spidev: use DECLARE_BITMAP instead of declaring the array
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Each SPI controller has exactly one CS line and as such doesn't
provide for multi-cs. We implement a workaround to support
multi-cs by _not_ configuring the mux'ed CS pin for each SPI
controller. The CS mechanism is assumed to be fully machine
specific - the driver doesn't even assume some GPIO pin is used
to control the CS.
The driver selects between DMA and POLLING mode depending upon
the xfer size - DMA mode for xfers bigger than FIFO size, POLLING
mode otherwise.
The driver has been designed to be capable of running SoCs since
s3c64xx and till date, for that reason some of the register fields
have been passed via, SoC specific, platform data.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
If len > BUFFER_LEN and !xfer->rx_buf we end up calculating the tx buffer
address as
*tx_dma = xfer->tx_dma + xfer->len - BUFFER_SIZE;
which is constant; i.e. we just send the last BUFFER_SIZE data over again
until we've reached the right number of bytes.
This patch gets around this by using the /requested/ length when
calculating addresses.
Note there's no way len != *plen when we calculate the rx buffer address
but conceptually we should be using *plen and I don't want someone to come
through later, see the calculations for rx and tx are different and "clean
up" back to what we had.
Signed-off-by: Ben Nizette <bn@niasdigital.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add pseudo-DMA by FIQ to the S3C24XX SPI driver. This allows the driver
to get DMA-like performance where there are either no free DMA channels or
when doing transfers that required both TX and RX data paths.
Since this patch requires the addition of an assembly file to hold the FIQ
code, we rename the module (instead of adding a rename of the .c file to
this patch). We expect most users are loading this via udev and thus
there should be no change to the userland configuration.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Driver for the Designware SPI core, it supports multipul interfaces like
PCI/APB etc. User can use "dw_apb_ssi_db.pdf" from Synopsys as HW
datasheet.
[randy.dunlap@oracle.com: fix build]
[akpm@linux-foundation.org: build fix]
Signed-off-by: Feng Tang <feng.tang@intel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The driver already uses __devexit_p() in the structure, but looks like
actual __dev{init,exit} markings were forgotten.
The spidev_spi driver also needs renaming to include a "_driver" suffix to
avoid section mismatch warnings.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6: (23 commits)
spi: fix probe/remove section markings
Add OMAP spi100k driver
spi-imx: don't access struct device directly but use dev_get_platdata
spi-imx: Add mx25 support
spi-imx: use positive logic to distinguish cpu variants
spi-imx: correct check for platform_get_irq failing
ARM: NUC900: Add spi driver support for nuc900
spi: SuperH MSIOF SPI Master driver V2
spi: fix spidev compilation failure when VERBOSE is defined
spi/au1550_spi: fix setupxfer not to override cfg with zeros
spi/mpc8xxx: don't use __exit_p to wrap plat_mpc8xxx_spi_remove
spi/i.MX: fix broken error handling for gpio_request
spi/i.mx: drain MXC SPI transfer buffer when probing device
MAINTAINERS: add SPI co-maintainer.
spi/xilinx_spi: fix incorrect casting
spi/mpc52xx-spi: minor cleanups
xilinx_spi: add a platform driver using the xilinx_spi common module.
xilinx_spi: add support for the DS570 IP.
xilinx_spi: Switch to iomem functions and support little endian.
xilinx_spi: Split into of driver and generic part.
...
Probe/remove functions need to be marked as __devinit and __devexit
(not __init an __exit) to prevent trying to run code that has been
discarded. This patch fixes the spi_imx driver to mark probe and
remove correctly.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This change adds the OMAP SPI 100k driver created by
Fabrice Crohas <fcrohas@gmail.com>. This SPI bus is found on
OMAP7xx-series smartphones, and for many, the touchscreen is
attached to this bus.
The lion's share of the work was done by Fabrice on this driver --
I am merely porting it from the Linwizard project on his behalf.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Manuel Lauss