Some RS690 chipsets seem to end up with floating connectors, either
a DVI connector isn't actually populated, or an add-in HDMI card
is available but not installed. In this case we seem to get a NULL byte
response for each byte of the i2c transaction, so we detect this
case and if we see it we don't do anymore DDC transactions on this
connector.
I've tested this on my RS690 without the HDMI card installed and
it seems to work fine.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Filter out modes that are higher than the max pixel
clock.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Don't try and en/disable the port as it may be a hpd event from
powering up/down the panel during a modeset or dpms.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In the hotplug handler, just use the drm dpms functions.
If the monitor is plugged in, turn it on, if it's not,
turn it off. This also reduces power usage by turning
off the encoder and crtc when the monitor is unplugged.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- reorganize the functions based on use
- clean up function naming
- rework link training to better match what we use internally
- add initial support for DP 1.2 (no MST yet)
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fusion hardware often has DP to VGA/LVDS/TMDS bridges to
handle non-DP encoders. Internally we treat them mostly
like DP.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
eDP is usually used as an LVDS replacement, so treat
it more like LVDS from the user perspective.
v2: encoder mode is always DP for eDP.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Sometimes the i2c test in i2c_bit_add_bus fails
if this happens we fail to register the i2c adapter and
eventually fail to add the connector. If i2c fails,
add the connector to the user can at least force
it on.
Note that some distros set i2c-algo-bit.bit_test to 1 by
default which sometimes fails preventing the ddc i2c adapter
from being added. The i2c adapter works even if the bit test
fails, probably due to pre/post_xfer not getting called in
the test_bit function. I have another patch to follow
up on that.
See:
https://bugs.freedesktop.org/show_bug.cgi?id=36221
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/vblank: update recently added vbl interface to be more future proof.
drm radeon: Return -EINVAL on wrong pm sysfs access
drm/radeon/kms: fix hardcoded EDID handling
Revert "drm/i915: Don't save/restore hardware status page address register"
drm/i915: Avoid unmapping pages from a NULL address space
drm/i915: Fix use after free within tracepoint
drm/i915: Restore missing command flush before interrupt on BLT ring
drm/i915: Disable pagefaults along execbuffer relocation fast path
drm/i915: Fix computation of pitch for dumb bo creator
drm/i915: report correct render clock frequencies on SNB
drm/i915/dp: Correct the order of deletion for ghost eDP devices
drm/i915: Fix tiling corruption from pipelined fencing
drm/i915: Re-enable self-refresh
drm/i915: Prevent racy removal of request from client list
drm/i915: skip redundant operations whilst enabling pipes and planes
drm/i915: Remove surplus POSTING_READs before wait_for_vblank
drm/radeon/kms: prefer legacy pll algo for tv-out
drm: check for modesetting on modeset ioctls
drm/kernel: vblank wait on crtc > 1
drm: Fix use-after-free in drm_gem_vm_close()
On some servers there is a hardcoded EDID provided
in the vbios so that the driver will always see a
display connected even if something like a KVM
prevents traditional means like DDC or load
detection from working properly. Also most
server boards with DVI are not actually DVI, but
DVO connected to a virtual KVM service processor.
If we fail to detect a monitor via DDC or load
detection and a hardcoded EDID is available, use
it.
Additionally, when using the hardcoded EDID, use
a copy of it rather than the actual one stored
in the driver as the detect() and get_modes()
functions may free it if DDC is successful.
This fixes the virtual KVM on several internal
servers.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Allows e.g. power management daemons to control the backlight level. Inspired
by the corresponding code in radeonfb.
[mjg@redhat.com: updated to add backlight type and make the connector the parent device]
Signed-off-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: David Airlie <airlied@linux.ie>
Acked-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Sedat Dilek <sedat.dilek@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
hdmi 1.3 raises the max clock from 165 Mhz to 340 Mhz.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Lots of HDMI TVs overscan the incoming image by default.
The underscan option was added as a way to compensate for
that by underscanning the image so that the edges would
not be cut off on an overscanning TV. However, the TV
provides no way of knowing whether it is overscanning or
not. If the user has disabled overscan on their TV or has a
TV that does not overscan, you will get black bars around the
edges of your screen. Prior to the patch we got complaints
and bug reports from users with overscanning TVs, now with
the patch, we get lots of complaints and bug reports from
users with non-overscanning TVs. There's no good default,
but on average there have been more users complaining about
it being on by default than off, so change it to off. This
will probably result in a new deluge of overscanning TV user
complaints. There's no winning.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'intel/drm-intel-next' of /ssd/git/drm-next: (771 commits)
drm/i915: Undo "Uncouple render/power ctx before suspending"
drm/i915: Allow the application to choose the constant addressing mode
drm/i915: dynamic render p-state support for Sandy Bridge
drm/i915: Enable EI mode for RCx decision making on Sandybridge
drm/i915/sdvo: Border and stall select became test bits in gen5
drm/i915: Add Guess-o-matic for pageflip timestamping.
drm/i915: Add support for precise vblank timestamping (v2)
drm/i915: Add frame buffer compression on Sandybridge
drm/i915: Add self-refresh support on Sandybridge
drm/i915: Wait for vblank before unpinning old fb
Revert "drm/i915: Avoid using PIPE_CONTROL on Ironlake"
drm/i915: Pass clock limits down to PLL matcher
drm/i915: Poll for seqno completion if IRQ is disabled
drm/i915/ringbuffer: Make IRQ refcnting atomic
agp/intel: Fix missed cached memory flags setting in i965_write_entry()
drm/i915/sdvo: Only use the SDVO pin if it is in the valid range
drm/i915: Enable RC6 autodownclocking on Sandybridge
drm/i915: Terminate the FORCE WAKE after we have finished reading
drm/i915/gtt: Clear the cachelines upon resume
drm/i915: Restore GTT mapping first upon resume
...
Some systems have the LCD width and height in mm available in the
LCD info table. Use this info if there is no EDID to provide it.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The eDP panel must be powered up for aux transactions, so power it
up for detect and mode probe functions, otherwise power it up or
down based on dpms.
v2:
- only mess with eDP panel on DCE4+
- only mess with eDP panel on eDP connectors, not all DP connectors
v3:
- be extra careful to only mess with eDP panels on eDP connectors
v4:
- avoid possible null derefernce if a connector has not been
assigned to the encoder
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is a follow on to:
26b5bc9864
(drm/radeon/kms: add support for router objects)
That patch added support for systems that use a mux to control
the ddc line routing between the connectors. This patch adds
support for systems that use a mux to control the encoder
clock and data path routing to the connectors.
Should fix:
https://bugs.freedesktop.org/show_bug.cgi?id=31339
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Make more of the connector code debug only to avoid
spamming the kernel logs with detect and add modes
messages.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This allows for a more exact fitting on the physical
display. The new properties default to zero which corresponds to the
previous underscan border width[height] formula:
(display_width[display_width] >> 5) + 16.
Example to set a horizontal border width of 30 and a vertikal border
height of 22:
xrandr --output HDMI-0 --set underscan on --set "underscan hborder" 30 --set "underscan vborder" 22
Signed-off-by: Marius Gröger <marius.groeger@googlemail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
v2: Julien Cristau pointed out that @nondestructive results in
double-negatives and confusion when trying to interpret the parameter,
so use @force instead. Much easier to type as well. ;-)
And fix the miscompilation of vmgfx reported by Sedat Dilek.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Destructive load-detection is very expensive and due to failings
elsewhere can trigger system wide stalls of up to 600ms. A simple
first step to correcting this is not to invoke such an expensive
and destructive load-detection operation automatically.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29536
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=16265
Reported-by: Bruno Prémont <bonbons@linux-vserver.org>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The tv parameter was added to disable the tv-out connector,
however, it caused a crash if it was set to 0 due to
drm_connector_init not getting called. If tv=0, don't
attempt to add the connector.
Might fix:
https://bugzilla.kernel.org/show_bug.cgi?id=17241
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If the connector is eDP, it can only be DP, not TMDS.
Always set the detected sink type. If the sink is
detected as non-DP, but there is no EDID, you can still
manually force the port on. If the sink type is DP
and there's no DPCD, there's no way to force the monitor
on since you need both ends to train the link.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On most newer asics, digital encoders have two links each
and they can be used independantly. As such, treat them as
separate encoders otherwise the individual links will not
get programmed properly at modeset time.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
router objects are found on systems that use a mux to control
ddc line to connector routing or to control the actual clock and data
routing from the chip to the connectors. This patch implements ddc line
routing.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Previously we added i2c buses as needed when enumerating connectors
power management, etc. This only exposed the actual buses used and
could have lead to the same buse getting created more than once if
one buses was used for more than one purpose. This patch sets up
all i2c buses on the card in one place and users of the buses just
point back to the one instance.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
R4xx also uses the atom add connector function, but underscan is only
supported on avivo chips.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This connector attribute allows you to enable or disable underscan
on a digital output to compensate for panels that automatically
overscan (e.g., many HDMI TVs). Valid values for the attribute are:
off - forces underscan off
on - forces underscan on
auto - enables underscan if an HDMI TV is connected, off otherwise
default value is auto.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This migrates a bunch of DRM_DEBUG->DRM_DEBUG_KMS so we can get more modesetting related info without all the other ioctl handling easily.
Also the PM code moves to DRM_DEBUG_DRIVER mostly.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes a regression caused by b2ea4aa67b
due to the way shared ddc with multiple digital connectors was handled.
You generally have two cases where DDC lines are shared:
- HDMI + VGA
- HDMI + DVI-D
HDMI + VGA is easy to deal with because you can check the EDID for the
to see if the attached monitor is digital. A shared DDC line with two
digital connectors is more complex. You can't use the hdmi bits in the
EDID since they may not be there with DVI<->HDMI adapters. In this case
all we can do is check the HPD pins to see which is connected as we have
no way of knowing using the EDID.
Reported-by: trapdoor6@gmail.com
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Connectors with a shared ddc line can be connected to different
encoders.
Reported by Pasi Kärkkäinen <pasik@iki.fi> on dri-devel
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
* anholt/drm-intel-next: (515 commits)
drm/i915: Fix out of tree builds
drm/i915: move fence lru to struct drm_i915_fence_reg
drm/i915: don't allow tiling changes on pinned buffers v2
drm/i915: Be extra careful about A/D matching for multifunction SDVO
drm/i915: Fix DDC bus selection for multifunction SDVO
drm/i915: cleanup mode setting before unmapping registers
drm/i915: Make fbc control wrapper functions
drm/i915: Wait for the GPU whilst shrinking, if truly desperate.
drm/i915: Use spatio-temporal dithering on PCH
[MTD] Remove zero-length files mtdbdi.c and internal.ho
pata_pcmcia / ide-cs: Fix bad hashes for Transcend and kingston IDs
libata: Fix several inaccuracies in developer's guide
slub: Fix bad boundary check in init_kmem_cache_nodes()
raid6: fix recovery performance regression
KEYS: call_sbin_request_key() must write lock keyrings before modifying them
KEYS: Use RCU dereference wrappers in keyring key type code
KEYS: find_keyring_by_name() can gain access to a freed keyring
ALSA: hda: Fix 0 dB for Packard Bell models using Conexant CX20549 (Venice)
ALSA: hda - Add quirk for Dell Inspiron 19T using a Conexant CX20582
ALSA: take tu->qlock with irqs disabled
...
After thinking it over a lot it made more sense for the core to deal with
the output polling especially so it can notify X.
v2: drop plans for fake connector - per Michel's comments - fix X patch sent to xorg-devel, add intel polled/hpd setting, add initial nouveau polled/hpd settings.
v3: add config lock take inside polling, add intel/nouveau poll init/fini calls
v4: config lock was a bit agressive, only needed around connector list reading.
otherwise it could re-enter.
glisse: discard drm_helper_hpd_irq_event
v3: Reviewed-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/radeon/r300.c
The BSD ringbuffer support that is landing in this branch
significantly conflicts with the Ironlake PIPE_CONTROL fix on master,
and requires it to be tested successfully anyway.
DVI-D doesn't have analog. This matches the avivo behavior.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* drm-fbdev-cleanup:
drm/fb: remove drm_fb_helper_setcolreg
drm/kms/fb: use slow work mechanism for normal hotplug also.
drm/kms/fb: add polling support for when nothing is connected.
drm/kms/fb: provide a 1024x768 fbcon if no outputs found.
drm/kms/fb: separate fbdev connector list from core drm connectors
drm/kms/fb: move to using fb helper crtc grouping instead of core crtc list
drm/fb: fix fbdev object model + cleanup properly.
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/nouveau/nouveau_drv.h
On systems with the tv dac shared between DVI and TV,
we can only use the dac for one of the connectors.
However, when using a digital monitor on the DVI port,
you can use the dac for the TV connector just fine.
Check the use_digital status when resolving the conflict.
Fixes fdo bug 27649, possibly others.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On X startup we were getting a flicker where there shouldn't have been one.
the X DDX calls the kernel to set the properties to the same values (yes
it could be smarter), however the kernel was doing a pointless modeset then,
making my nice smooth boot ugly.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This breaks the connection between the core drm connector list
and the fbdev connector usage, and allows them to become disjoint
in the future. It also removes the untype void* that was in the
connector struct to support this.
All connectors are added to the fbdev now but this could be
changed in the future.
Signed-off-by: Dave Airlie <airlied@redhat.com>
bad cast was overwriting the tvdac adj values
Fixes fdo bug 27478
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This allows us to remove the internal bit algo bus used by
the radeon i2c algo. We now register a radeon algo adapter
if the gpio line is hw capable and the hw inplementation is
available, otherwise we register a bit algo adapter.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher