Add support for front jack channel selector which is present on EMU0204.
It allows to get 4 channels out of this soundcard.
Tested-by: Yury Bushmelev <jay@jay-tech.ru>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
According to USB Audio spec v2 bits 25 and 26 of bmChannelConfig are
"Back Left of Center - BLC" and "Back Right of Center - BRC",
respectively.
They are currently assigned to ALSA channels BLC/BRC. However, the ALSA
BLC/BRC are actually the rather nonsensical "bottom left center" and
"bottom right center", so the channels will be assigned wrongly. The
comments in the USB code are also similarly wrong, so this is not
readily apparent without looking at the actual specification.
Fix the channel mapping by mapping bits 25 and 26 to RLC (Rear Left
Center) and RRC (Rear Right Center), respectively, instead.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In case the channel count of the input terminal is not the same as
the channel count of the streaming descriptor, the channel config of
the input terminal can not be trusted. Instead fall back to a default
(guessed) channel map.
This was found on a Logitech USB Headset.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The channel config from the streaming descriptor is probably a
better indicator of the channel map than the input terminal.
Use the input terminal's channel map as fallback only.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If wChannelconfig is given for some formats but not others, userspace
might not be able to set the channel map.
This is RFC because I'm not sure what the best behaviour is - to guess
the channel map from the given number of channels (it's quite likely
that one channel is MONO and two channels is FL FR), or just to supply
UNKNOWN for all channels.
But the complete lack of channel map for a format leads userspace to
believe that the format is not available at all. Or am I
misunderstanding how this should be used?
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The probe code of snd-usb-6fire driver overrides the devices[] pointer
wrongly without checking whether it's already occupied or not. This
would screw up the device disconnection later.
Spotted by coverity CID 141423.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Further work on the dmaengine helpers, including support for
configuring the parameters for DMA by reading the capabilities of the
DMA controller which removes some guesswork and magic numbers fromm
drivers.
- A refresh of the documentation.
- Conversions of many drivers to direct regmap API usage in order to
allow the ASoC level register I/O code to be removed, this will
hopefully be completed by v3.14.
- Support for using async register I/O in DAPM, reducing the time taken
to implement power transitions on systems that support it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=rVsK
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v3.13
- Further work on the dmaengine helpers, including support for
configuring the parameters for DMA by reading the capabilities of the
DMA controller which removes some guesswork and magic numbers fromm
drivers.
- A refresh of the documentation.
- Conversions of many drivers to direct regmap API usage in order to
allow the ASoC level register I/O code to be removed, this will
hopefully be completed by v3.14.
- Support for using async register I/O in DAPM, reducing the time taken
to implement power transitions on systems that support it.
The pcm_usb_stream plugin requires the mremap explicitly for the read
buffer, as it expands itself once after reading the required size.
But the commit [314e51b9: mm: kill vma flag VM_RESERVED and
mm->reserved_vm counter] converted blindly to a combination of
VM_DONTEXPAND | VM_DONTDUMP like other normal drivers, and this
resulted in the failure of mremap().
For fixing this regression, we need to remove VM_DONTEXPAND for the
read-buffer mmap.
Reported-and-tested-by: James Miller <jamesstewartmiller@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds support for dev speed USB_SPEED_WIRELESS in
snd_usb_parse_datainterval which allows the usb sound core to create
ISO urbs with the correct number and size of buffers.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As Clemens Ladisch kindly explained:
"Please note that there are two methods to identify alternate settings:
the number, which is the value in bAlternateSetting, and the index,
which is the index in the descriptor array. There might be some wording
in the USB spec that these two values must be the same, but in reality,
[insert standard rant about firmware writers], bAlternateSetting
must be treated as a random ID value."
This patch changes the name to express the correct usage semantics.
No functional change.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If setting the interface fails, the SUBSTREAM_FLAG_SYNC_EP_STARTED
should be cleared.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The return value of snd_usb_endpoint_deactivate() is not used,
make the function have no return value.
Update the documentation to reflect what the function is actually
doing.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If an endpoint in use, its associated URBs should not be
deactivated.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The only call site for deactivate_endpoints() at snd_usb_hw_free().
The return value is not checked there, as it is irrelevant if it
fails on hw_free.
This patch moves the deactivation of the endpoints directly into
snd_usb_hw_free().
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the format is not actually used in sync_ep_set_params(),
there is no need to pass it down.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The frame check in i_usX2Y_urb_complete() and
i_usX2Y_usbpcm_urb_complete() is bogus and produces false positives as
described in this LAU thread:
http://linuxaudio.org/mailarchive/lau/2013/5/20/200177
This patch removes the check code entirely.
Cc: fzu@wemgehoertderstaat.de
Reported-by: Dr Nicholas J Bailey <nicholas.bailey@glasgow.ac.uk>
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds LED support for the Native Instruments Maschine
Controller. It adds ALSA controls for dimming the LEDs of all
buttons and the backlight of the two displays.
Signed-off-by: Hannes Gräuler <hgraeule@uos.de>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch changes the way URBs are allocated and their sizes are
determined for PCM playback in the snd-usb-audio driver. Currently
the driver allocates too few URBs for endpoints that don't use
implicit sync, making underruns more likely to occur. This may be a
holdover from before I/O delays could be measured accurately; in any
case, it is no longer necessary.
The patch allocates as many URBs as possible, subject to four
limitations:
The total number of URBs for the endpoint is not allowed to
exceed MAX_URBS (which the patch increases from 8 to 12).
The total number of packets per URB is not allowed to exceed
MAX_PACKS (or MAX_PACKS_HS for high-speed devices), which is
decreased from 20 to 6.
The total duration of queued data is not allowed to exceed
MAX_QUEUE, which is decreased from 24 ms to 18 ms.
The total number of ALSA frames in the output queue is not
allowed to exceed the ALSA buffer size.
The last requirement is the hardest to implement. Currently the
number of URBs needed to fill a buffer cannot be determined in
advance, because a buffer contains a fixed number of frames whereas
the number of frames in an URB varies to match shifts in the device's
clock rate. To solve this problem, the patch changes the logic for
deciding how many packets an URB should contain. Rather than using as
many as possible without exceeding an ALSA period boundary, now the
driver uses only as many packets as needed to transfer a predetermined
number of frames. As a result, unless the device's clock has an
exceedingly variable rate, the number of URBs making up each period
(and hence each buffer) will remain constant.
The overall effect of the patch is that playback works better in
low-latency settings. The user can still specify values for
frames/period and periods/buffer that exceed the capabilities of the
hardware, of course. But for values that are within those
capabilities, the performance will be improved. For example, testing
shows that a high-speed device can handle 32 frames/period and 3
periods/buffer at 48 KHz, whereas the current driver starts to get
glitchy at 64 frames/period and 2 periods/buffer.
A side effect of these changes is that the "nrpacks" module parameter
is no longer used. The patch removes it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Clemens Ladisch <clemens@ladisch.de>
Tested-by: Daniel Mack <zonque@gmail.com>
Tested-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Convert 0 to false and 1 to true when assigning values to bool
variables. Inspired by commit 3db1cd5c05.
The simplified semantic patch that find this problem is as
follows (http://coccinelle.lip6.fr/):
@@
bool b;
@@
(
-b = 0
+b = false
|
-b = 1
+b = true
)
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- DAPM is now mandatory for CODEC drivers in order to avoid the repeated
regressions in the special cases for non-DAPM CODECs and make it
easier to integrate with other components on boards. All existing
drivers have had some level of DAPM support added.
- A lot of cleanups in DAPM plus support for maintaining controls in a
specific state while a DAPM widget all contributed by Lars-Peter Clausen.
- Core helpers for bitbanged AC'97 reset from Markus Pargmann.
- New drivers and support for Analog Devices ADAU1702 and ADAU1401(a),
Asahi Kasei Microdevices AK4554, Atmel AT91ASM9x5 and WM8904 based
machines, Freescale S/PDIF and SSI AC'97, Renesas R-Car SoCs, Samsung
Exynos5420 SoCs, Texas Instruments PCM1681 and PCM1792A and Wolfson
Microelectronics WM8997.
- Support for building drivers that can support it cross-platform for
compile test.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=qzif
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v3.12
- DAPM is now mandatory for CODEC drivers in order to avoid the repeated
regressions in the special cases for non-DAPM CODECs and make it
easier to integrate with other components on boards. All existing
drivers have had some level of DAPM support added.
- A lot of cleanups in DAPM plus support for maintaining controls in a
specific state while a DAPM widget all contributed by Lars-Peter Clausen.
- Core helpers for bitbanged AC'97 reset from Markus Pargmann.
- New drivers and support for Analog Devices ADAU1702 and ADAU1401(a),
Asahi Kasei Microdevices AK4554, Atmel AT91ASM9x5 and WM8904 based
machines, Freescale S/PDIF and SSI AC'97, Renesas R-Car SoCs, Samsung
Exynos5420 SoCs, Texas Instruments PCM1681 and PCM1792A and Wolfson
Microelectronics WM8997.
- Support for building drivers that can support it cross-platform for
compile test.
Add the volume control quirk for avoiding the kernel warning
for the Logitech HD Webcam C525
as in the similar commit 36691e1be6
for the Logitech HD Webcam C310.
Reported-by: Maksim Boyko <maksim.a.boyko@gmail.com>
Tested-by: Maksim Boyko <maksim.a.boyko@gmail.com>
Cc: <stable@vger.kernel.org> # 3.10.5+
Signed-off-by: Maksim Boyko <maksim.a.boyko@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit aafe77cc45 (ALSA: usb-audio: add support for many Roland/Yamaha
devices) had several logic errors that prevented create_auto_midi_quirk
from enumerating any MIDI ports.
Reported-by: Keith A. Milner <maillist@superlative.org>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Patch makes pcm buffers DMA-able by allocating each one separately.
Signed-off-by: Torsten Schenk <torsten.schenk@zoho.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is no need to pass constants via stack. The width may be explicitly
specified in the format.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The driver used to assume that the streaming endpoint's wMaxPacketSize
value would be an indication of how much data the endpoint expects or
sends, and compute the number of packets per URB using this value.
However, the Focusrite Scarlett 2i4 declares a value of 1024 bytes,
while only about 88 or 44 bytes are be actually used. This discrepancy
would result in URBs with far too few packets, which would not work
correctly on the EHCI driver.
To get correct URBs, use wMaxPacketSize only as an upper limit on the
packet size.
Reported-by: James Stone <jamesmstone@gmail.com>
Tested-by: James Stone <jamesmstone@gmail.com>
Cc: <stable@vger.kernel.org> # 2.6.35+
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Patch fixes 6fire not to use stack as URB transfer_buffer. URB buffers need to
be DMA-able, which stack is not. Furthermore, transfer_buffer should not be
allocated as part of larger device structure because DMA coherency issues and
patch fixes this issue too.
Cc: stable@vger.kernel.org
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Tested-by: Torsten Schenk <torsten.schenk@zoho.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Prevent NULL dereference in snd_usb_add_endpoints(), when
alts is passed as NULL. In this case, WARN (since this is
a non-fatal bug) and return NULL ep. Call sites treat a NULL
return value as an error.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the quirks all apply to implicit feedback (the source endpoint
is always a data endpoint), there's no need to set and check
a flag for it.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
An implicit feedback endpoint can only be a capture source. The
consumer (sink) of the implicit feedback endpoint is therefore limited
to playback EPs.
Check if the target endpoint is a playback first and remove redundant
checks.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since implicit_fb is not changed, !implicit_fb will always
be true - it is set only after these checks.
Similarly, there's also no need to set it at the top of the function.
Change the type of implicit_fb to bool (more appropriate).
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reverse logic on the conditions required to qualify for a sync endpoint
and remove one level of indendation.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Separate setting implicit feedback quirks from setting
a sync endpoint (which may also be explicit feedback or async).
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Setting the sync endpoint currently takes up about half of set_format().
Move it to a dedicated function.
No functional change.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The test here is always true because S[i].urb is an array not a pointer.
Also it's bogus because the intent was to test:
if (S->urb[i]) {
instead of:
if (S[i].urb) {
Anyway, usb_kill_urb() and usb_free_urb() accept NULL pointers so we can
just remove this.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Return SNDRV_PCM_POS_XRUN (snd_pcm_uframes_t) instead of
SNDRV_PCM_STATE_XRUN (snd_pcm_state_t) from the pointer
function of hiface, as expected by snd_pcm_update_hw_ptr0().
Caught by sparse.
Cc: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Return SNDRV_PCM_POS_XRUN (snd_pcm_uframes_t) instead of
SNDRV_PCM_STATE_XRUN (snd_pcm_state_t) from the pointer
function of 6fire, as expected by snd_pcm_update_hw_ptr0().
Caught by sparse.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_pcm_stop() must be called in the PCM substream lock context.
Cc: <stable@vger.kernel.org>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 8f898e92ae removed the redundant
reads of bInterfaceProtocol from the descriptors, but introduced a
regression to devices with quirks of type QUIRK_AUDIO_FIXED_ENDPOINT,
since fp->protocol is not set in setup process.
As a consequence, audio streams would not get initialized, as the
following logs show:
[ 48.923043] setting usb interface 3:1
[ 48.923056] Creating new capture data endpoint #81
[ 48.923484] 4:3:1: cannot set freq 48000 to ep 0x81
This patch sets fp->protocol in create_fixed_stream_quirk() and
resolves the regression.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch is adding extensive support (beside standard usb audio class)
for Audio Advantage Micro II usb sound card.
Features included:
- Access to AES bits (so now sending the IEC61937 compliant stream is
possible).
- Mixer SPDIF control added to turn on/off the optical transmitter.
Signed-off-by: Przemek Rudy <prudy1@o2.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For adding support for many Roland and Yamaha devices:
* 'full-roland-support' of git://git.alsa-project.org/alsa-kprivate:
ALSA: usb-audio: add quirks for Roland QUAD/OCTO-CAPTURE
ALSA: usb-audio: claim autodetected PCM interfaces all at once
ALSA: usb-audio: remove superfluous Roland quirks
ALSA: usb-audio: add MIDI port names for some Roland devices
ALSA: usb-audio: add support for many Roland/Yamaha devices
ALSA: usb-audio: detect implicit feedback on Roland devices
ALSA: usb-audio: store protocol version in struct audioformat
The Roland Quad/Octo-Capture devices use some unknown vendor-specific
mechanism to switch sample rates (and to manage other controls). To
prevent the driver from attempting to use any other than the default
44.1 kHz sample rate, use quirks to hide the other alternate settings.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
snd_card_register() registers all devices newly added since the last
call. However, the playback/capture streams are handled as one ALSA
device, so the second /dev device will not be registered if the PCM
streams are added in two steps.
QUIRK_AUTODETECT caused the probe callback to be called once for each
interface, which triggered this problem. Work around this by handling
this like the composite quirk, i.e., autodetecting all other interfaces
that might be used for PCM or MIDI.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Remove all quirks that are no longer needed now that the generic Roland
quirks can handle the vendor-specific descriptors correctly.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Add quirks to detect the various vendor-specific descriptors used by
Roland and Yamaha in most of their recent USB audio and MIDI devices.
Together with the previous patch, this should add audio/MIDI support for
the following USB devices:
- Edirol motion dive .tokyo performance package
- Roland MC-808 Synthesizer
- Roland BK-7m Synthesizer
- Roland VIMA JM-5/8 Synthesizer
- Roland SP-555 Sequencer
- Roland V-Synth GT Synthesizer
- Roland Music Atelier AT-75/100/300/350C/500/800/900/900C Organ
- Edirol V-Mixer M-200i/300/380/400/480/R-1000
- BOSS GT-10B Effects Processor
- Roland Fantom G6/G7/G8 Keyboard
- Cakewalk Sonar V-Studio 20/100/700 Audio Interface
- Roland GW-8 Keyboard
- Roland AX-Synth Keyboard
- Roland JUNO-Di/STAGE/Gi Keyboard
- Roland VB-99 Effects Processor
- Cakewalk UM-2G MIDI Interface
- Roland A-500S Keyboard
- Roland SD-50 Synthesizer
- Roland OCTAPAD SPD-30 Controller
- Roland Lucina AX-09 Synthesizer
- BOSS BR-800 Digital Recorder
- Roland DUO/TRI-CAPTURE (EX) Audio Interface
- BOSS RC-300 Loop Station
- Roland JUPITER-50/80 Keyboard
- Roland R-26 Recorder
- Roland SPD-SX Controller
- BOSS JS-10 Audio Player
- Roland TD-11/15/30 Drum Module
- Roland A-49/88 Keyboard
- Roland INTEGRA-7 Synthesizer
- Roland R-88 Recorder
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
All the Roland/Edirol/BOSS USB audio devices that need implicit feedback
show this unambiguously in their descriptors, so it might be a good idea
to let the driver detect this.
This should make playback work correctly (at least with Jack) with the
following devices:
- BOSS GT-100
- BOSS JS-8 Jam Station
- Edirol M-16DX
- Roland GAIA SH-01
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Instead of reading bInterfaceProtocol from the descriptor whenever it's
needed, store this value in the audioformat structure. Besides
simplifying some code, this will allow us to correctly handle vendor-
specific devices where the descriptors are marked with other values.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
In sound/usb/card.c and sound/usb/misc/ua101.c there are no spaces
between the vendor and the device names, use this style in the other
drivers too.
This also helps keeping consistency when new drivers copies from the
ones already in the mainline tree.
Signed-off-by: Antonio Ospite <ao2@amarulasolutions.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For USB devices it's not necessary to allocate physically contiguous
buffers.
Signed-off-by: Antonio Ospite <ao2@amarulasolutions.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For USB devices it's not necessary to allocate physically contiguous
buffers.
Signed-off-by: Antonio Ospite <ao2@amarulasolutions.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The snd_card_used variable is only read but never written, remove it.
Signed-off-by: Antonio Ospite <ao2@amarulasolutions.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just like the previous fix for LogitechHD Webcam c270 in commit
11e7064f35, c310 model also requires the
same workaround for avoiding the kernel warning.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=59741
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the Android firmware enables the audio interfaces in accessory
mode, it always declares in the control interface's baInterfaceNr array
that interfaces 0 and 1 belong to the audio function. However, the
accessory interface itself, if also enabled, already is at index 0 and
shifts the actual audio interface numbers to 1 and 2, which prevents the
PCM streaming interface from being seen by the host driver.
To get the PCM interface interface to work, detect when the descriptors
point to the (for this driver useless) accessory interface, and redirect
to the correct one.
Reported-by: Jeremy Rosen <jeremy.rosen@openwide.fr>
Tested-by: Jeremy Rosen <jeremy.rosen@openwide.fr>
Cc: <stable@vger.kernel.org>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 927c9423dd (ALSA: usb-audio: add
Edirol UM-3G support) used a wrong quirk type, which would make the
driver refuse to attach with the error message "MIDIStreaming interface
descriptor not found".
Cc: <stable@vger.kernel.org> # 3.3 and later
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Check only the uppermost 16 bits instead of the whole 32 bits of
the version information. Do this because all firmware version tested
with this version information worked correctly and the strict check
causes problems for several users.
Signed-off-by: Torsten Schenk <torsten.schenk@zoho.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
freqshift is only set for the data endpoint and syncmaxsize is only set
for the sync endpoint. This results in a syncmaxsize of zero used in the
proc output feedback format calculation, which gives a feedback format
incorrectly shown as 8.16 for UAC2 devices.
As neither the data nor the sync endpoint gives all the relevant
content, output the two combined.
Also remove the sync_endpoint "packet size" which is always zero
and the sync_endpoint "momentary freq" which is constant.
Tested with UAC2 async and UAC1 adaptive, not tested with UAC1 async.
Reported-by: B. Zhang <bb.zhang@free.fr>
Signed-off-by: Torstein Hegge <hegge@resisty.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Current code does this:
be16_to_cpu(buf[i * 2] << 8 | buf[(i * 2) + 1])
Which is effectively (neglecting the index):
be16_to_cpu(be16_to_cpu(*((u16 *) buf)))
This means the int16 in the buffer is not converted at all.
Daniel Mack confirmed that the driver works on little endian
CPUs, leading to the conclusion that the device-side structure
is actually little endian.
This changes the code to use le16_to_cpu().
Caught by sparse.
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a function to handle conversion from snd_pcm_format_t
to bitwise with proper typing.
Change such conversions to use this function and silence sparse
warnings.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent changes in the USB API ("implement new semantics for
URB_ISO_ASAP") made the former meaning of the URB_ISO_ASAP flag the
default, and changed this flag to mean that URBs can be delayed.
This is not the behaviour wanted by any of the audio drivers because
it leads to discontinuous playback with very small period sizes.
Therefore, our URBs need to be submitted without this flag.
Reported-by: Joe Rayhawk <jrayhawk@fairlystable.org>
Cc: <stable@vger.kernel.org> # 3.8 only
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Scarlett 2i2 seems to take almost 500 ms to set the sample rate,
even if the clock is currently set to that value. This patch speeds
up prepare of the device, by avoiding setting the clock to something
it already is.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've got strange errors in get_ctl_value() in mixer.c during
probing, e.g. on Hercules RMX2 DJ Controller:
ALSA mixer.c:352 cannot get ctl value: req = 0x83, wValue = 0x201, wIndex = 0xa00, type = 4
ALSA mixer.c:352 cannot get ctl value: req = 0x83, wValue = 0x200, wIndex = 0xa00, type = 4
....
It turned out that the culprit is autopm: snd_usb_autoresume() returns
-ENODEV when called during card->probing = 1.
Since the call itself during card->probing = 1 is valid, let's fix the
return value of snd_usb_autoresume() as success.
Reported-and-tested-by: Daniel Schürmann <daschuer@mixxx.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The USB_DT_CS_ENDPOINT class-specific endpoint descriptor is usually
stuffed directly after the standard USB endpoint descriptor, and this is
where the driver currently expects it to be.
There are, however, devices in the wild that have it the other way
around in their descriptor sets, so the USB_DT_CS_ENDPOINT comes
*before* the standard enpoint. Devices known to implement it that way
are "Sennheiser BTD-500" and Plantronics USB headsets.
When the driver can't find the USB_DT_CS_ENDPOINT, it won't be able to
change sample rates, as the bitmask for the validity of this command is
storen in bmAttributes of that descriptor.
Fix this by searching the entire interface instead of just the extra
bytes of the first endpoint, in case the latter fails.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-and-tested-by: Torstein Hegge <hegge@resisty.net>
Reported-and-tested-by: Yves G <alsa-user@vivigatt.com>
Cc: stable@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Set the timeout for USB control set messages according to the USB 2
spec, using the macros from include/linux/usb.h.
The get timout becomes 5000 ms even though it is 500 ms in the
spec. This patch is required to run the Hercules RMX2 which needs a
timeout of 1240 ms.
More notes from author:
I still distinguish between set and get but as long both are 5000 ms
GCC will remove it anyway. IMHO this is more easy read and there is no
need to explain why we use a get timeout for set messages.
Signed-off-by: Daniel Schürmann <daschuer@mixxx.org>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The main additional change here is Lars-Peter's DMA work plus the
platform conversions which have been tested - getting this in mainline
will make life easier for development after the merge window. These
factor a large chunk of code out of the drivers for the platforms using
dmaengine, greatly simplifying development.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=MXrq
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: More updates for v3.10
The main additional change here is Lars-Peter's DMA work plus the
platform conversions which have been tested - getting this in mainline
will make life easier for development after the merge window. These
factor a large chunk of code out of the drivers for the platforms using
dmaengine, greatly simplifying development.
Unfortunately, none of the UAC standards provides a way to identify DSD
(Direct Stream Digital) formats. Hence, this patch adds a quirks
handler to identify USB interfaces that are capable of handling DSD.
That quirks handler can augment the already parsed formats bit-field,
by any of the new SNDRV_PCM_FMTBIT_DSD_{U8_U16} and setting the dsd_dop
flag in the audio format, if the driver should take care for the DOP
byte stuffing.
The only devices that are known to work with this are the ones with
a 'Playback Designs' vendor id.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is quite some confusion around the bit-ordering in DSD samples,
and no general agreement that defines whether hardware is supposed to
expect the oldest sample in the MSB or the LSB of a byte.
ALSA will hence set the rule that on the software API layer, bytes
always carry the oldest bit in the most significant bit of a byte, and
the driver has to translate that at runtime in order to match the
hardware layout.
This patch adds support for this by adding a boolean flag to the
audio format struct.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In order to provide a compatibility way for pushing DSD
samples through ordinary PCM channels, the "DoP open Standard" was
invented. See http://www.dsd-guide.com for the official document.
The host is required to stuff DSD marker bytes (0x05, 0xfa,
alternating) in the MSB of 24 bit wide samples on the bus, in addition
to the 16 bits of actual DSD sample payload.
To support this, the hardware and software stride logic in the driver
has to be tweaked a bit, as we make the userspace believe we're
operating on 16 bit samples, while we in fact push one more byte per
channel down to the hardware.
The DOP runtime information is stored in struct snd_usb_substream, so
we can keep track of our state across multiple calls to
prepare_playback_urb_dsd_dop().
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For normal PCM transfer, this change has no effect, as the endpoint's
stride is always frame_bits/8. For DSD DOP streams, however, which is
added later, the hardware stride differs from the software stride, and
the endpoint has the correct information in these cases.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 88a8516a21 (ALSA: usbaudio: implement USB autosuspend)
introduced autopm for all USB audio/MIDI devices. However, many MIDI
devices, such as synthesizers, do not merely transmit MIDI messages but
use their MIDI inputs to control other functions. With autopm, these
devices would get powered down as soon as the last MIDI port device is
closed on the host.
Even some plain MIDI interfaces could get broken: they automatically
send Active Sensing messages while powered up, but as soon as these
messages cease, the receiving device would interpret this as an
accidental disconnection.
Commit f5f165418c (ALSA: usb-audio: Fix missing autopm for MIDI input)
introduced another regression: some devices (e.g. the Roland GAIA SH-01)
are self-powered but do a reset whenever the USB interface's power state
changes.
To work around all this, just disable autopm for all USB MIDI devices.
Reported-by: Laurens Holst
Cc: <stable@vger.kernel.org>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When recording at 176.2KHz or 192Khz, the device adds a 32-bit length
header to the capture packets, which obviously needs to be ignored for
recording to work properly.
Userspace expected: L0 L1 L2 R0 R1 R2
...but actually got: R2 L0 L1 L2 R0 R1
Also, the last byte of the length header being interpreted as L0 of
the first sample caused spikes every 0.5ms, resulting in a loud 16KHz
tone (about the highest 'B' on a piano) being present throughout
captures.
Tested at all sample rates on an E-Mu 0404USB, and tested for
regressions on a generic USB headset.
Signed-off-by: Calvin Owens <jcalvinowens@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It turns out the devices from Playback Design need the delay quirk
after usb_set_interface from clocks.c as well. Make it a proper
quirks function and factor out the code to quirks.c.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The usb_control_msg() function expects __u16 types and performs
the endianness conversions by itself.
However, in three places, a conversion is performed before it is
handed over to usb_control_msg(), which leads to a double conversion
(= no conversion):
* snd_usb_nativeinstruments_boot_quirk()
* snd_nativeinstruments_control_get()
* snd_nativeinstruments_control_put()
Caught by sparse:
sound/usb/mixer_quirks.c:512:38: warning: incorrect type in argument 6 (different base types)
sound/usb/mixer_quirks.c:512:38: expected unsigned short [unsigned] [usertype] index
sound/usb/mixer_quirks.c:512:38: got restricted __le16 [usertype] <noident>
sound/usb/mixer_quirks.c:543:35: warning: incorrect type in argument 5 (different base types)
sound/usb/mixer_quirks.c:543:35: expected unsigned short [unsigned] [usertype] value
sound/usb/mixer_quirks.c:543:35: got restricted __le16 [usertype] <noident>
sound/usb/mixer_quirks.c:543:56: warning: incorrect type in argument 6 (different base types)
sound/usb/mixer_quirks.c:543:56: expected unsigned short [unsigned] [usertype] index
sound/usb/mixer_quirks.c:543:56: got restricted __le16 [usertype] <noident>
sound/usb/quirks.c:502:35: warning: incorrect type in argument 5 (different base types)
sound/usb/quirks.c:502:35: expected unsigned short [unsigned] [usertype] value
sound/usb/quirks.c:502:35: got restricted __le16 [usertype] <noident>
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some clocks might be read-only, e.g., external clocks (see also
UAC2 4.7.2.1).
In this case, setting the sample frequency will always fail
(even if the rate is equal to the current clock rate),
therefore do not write, but read the value and compare to the
requested rate.
If the clock is read only, avoid reading it twice.
If it doesn't match, return -ENXIO since the clock is invalid for
this configuration.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Show the error code returned from the USB subsystem in
the debug messages.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a module param to disable auto clock selection.
This is provided for users that expect the audio stream to
fail when the clock source is invalid (e.g., the word clock
was unintentionally disconnected).
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If a selector is available on a device, it may be pointing to a
clock source which is currently invalid.
If there is a valid clock source which can be selected, switch
to it.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the check that parse_audio_format_rates_v2() do after
receiving the clock source entity ID directly into the find
function and add a validation flag to the function.
This patch does not introduce any logic flow change.
It is provided to allow introducing automatic clock switching
easier later. By moving this uac_clock_source_is_valid callsite,
2 additional callsites can be avoided.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace the endianness conversions with the kernel-wide swabbing macros
in get/set_sample_rate_v2.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Correct spelling of snd_usb_endpoint_implict_feedback_sink in all
occurances.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Minor style fix, following a general code style in the kernel.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just for cleaning up, introduce a new function get_sample_rate_v2()
for replacing two identical calls in set_sample_rate_v2().
No functional change.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The C-Media CM6631 USB receiver doesn't respond to changes in sample rate
while the interface is active. The same behavior is observed in other UAC2
hardware like the VIA VT1731.
Reset the interface after setting the sampling frequency on sample rate
changes, to ensure that the sample rate set by snd_usb_init_sample_rate() is
used. Otherwise, the device will try to use the sample rate of the previous
stream, causing distorted sound on sample rate changes.
The reset is performed for all UAC2 devices, as it should not affect a
standards compliant device, but it is only necessary for C-Media CM6631,
VIA VT1731 and possibly others.
Failure to read sample rate from the device is not handled as an error in
set_sample_rate_v2(), as (permanent or intermittent) failure to read sample
rate isn't essential for a successful sample rate set.
Signed-off-by: Torstein Hegge <hegge@resisty.net>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge back for-linus branch for the badness table adjustment for VIA codecs
* for-linus:
ALSA: hda - Fix DAC assignment for independent HP
ALSA: hda - Fix abuse of snd_hda_lock_devices() for DSP loader
ALSA: hda - Fix typo in checking IEC958 emphasis bit
ALSA: snd-usb: mixer: ignore -EINVAL in snd_usb_mixer_controls()
ALSA: snd-usb: mixer: propagate errors up the call chain
ALSA: usb: Parse UAC2 extension unit like for UAC1
ALSA: hda - Fix yet missing GPIO/EAPD setup in cirrus driver
Creation of individual mixer controls may fail, but that shouldn't cause
the entire mixer creation to fail. Even worse, if the mixer creation
fails, that will error out the entire device probing.
All the functions called by parse_audio_unit() should return -EINVAL if
they find descriptors that are unsupported or believed to be malformed,
so we can safely handle this error code as a non-fatal condition in
snd_usb_mixer_controls().
That fixes a long standing bug which is commonly worked around by
adding quirks which make the driver ignore entire interfaces. Some of
them might now be unnecessary.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-and-tested-by: Rodolfo Thomazelli <pe.soberbo@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In check_input_term() and parse_audio_feature_unit(), propagate the
error value that has been returned by a failing function instead of
-EINVAL. That helps cleaning up the error pathes in the mixer.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
UAC2_EXTENSION_UNIT_V2 differs from UAC1_EXTENSION_UNIT, but can be handled in
the same way when parsing the unit. Otherwise parse_audio_unit() fails when it
sees an extension unit on a UAC2 device.
UAC2_EXTENSION_UNIT_V2 is outside the range allocated by UAC1.
Signed-off-by: Torstein Hegge <hegge@resisty.net>
Acked-by: Daniel Mack <zonque@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
"Playback Design" products need a 50ms delay after setting the USB
interface.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Andreas Koch <andreas@akdesigninc.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
UAC2 compliant audio devices may announce the capability to transport
raw audio data on their endpoints. Catch this and handle it as
'special' stream on the ALSA side.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Andreas Koch <andreas@akdesigninc.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This field may use up to 32 bits, so it should be handled as unsigned
int.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Andreas Koch <andreas@akdesigninc.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The maxpacksize field is given in some quirks, but it gets ignored (in
favour of wMaxPacketSize from the first endpoint.) This patch favours
the one in the quirk.
Digidesign Mbox and Mbox 2 are the only affected quirks and the devices
are assumed to be working without this patch. So for safety against the
values in the quirk being incorrect, remove them.
The datainterval is also ignored but there are not currently any quirks
which choose to override this.
Cc: Damien Zammit <damien@zamaudio.com>
Cc: Chris J Arges <christopherarges@gmail.com>
Signed-off-by: Mark Hills <mark@xwax.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The hardware also has a PCM capture device which is not implemented in
this patch.
It may be possible to generalise this to Saffire 6 USB support and some
of the other Focusrite interfaces, but as I don't have access to these
devices we should wait until capture support is working first.
Capture support is not implemented because the code assumes the endpoint
to have its own interface (instead, it shares the interface with playback)
and some thought will be needed to lift this limitation.
Signed-off-by: Mark Hills <mark@xwax.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The NuForce UDH-100 numbers its interfaces incorrectly, which makes the
interface associations come out wrong, which results in the driver
erroring out with the message "Audio class v2 interfaces need an
interface association".
Work around this by searching for the interface association descriptor
also in some other place where it might have ended up.
Reported-and-tested-by: Dave Helstroom <helstroom@google.com>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix three smatch warnings recently introduced:
sound/usb/caiaq/device.c:166 usb_ep1_command_reply_dispatch() warn:
variable dereferenced before check 'cdev' (see line 163)
sound/usb/caiaq/device.c:517 snd_disconnect() warn: variable
dereferenced before check 'card' (see line 514)
sound/usb/caiaq/input.c:510 snd_usb_caiaq_ep4_reply_dispatch() warn:
variable dereferenced before check 'cdev' (see line 506)
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Get rid of the proprietary functions log() and debug() and use the
generic dev_*() approach. A macro is needed to cast a cdev to a struct
device *.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is needed in order to make the device namespace cleaner, and will
help when moving this driver over to dev_*() logging.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
bootresponse in snd_usb_mbox2_boot_quirk is only 12 (decimal) u8's
long, but i9s passed to snd_usb_ctl_msg as it would be 0x12 (hexa)
long. Fix that by having proper size of the array, i.e. 0x12.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adds quirks and mixer support for the M-Audio Fast Track C600 USB
audio interface. This device is very similar to the C400 - the C600
simply has some more inputs and outputs, so the existing C400 support
is extended to support this device as well.
Signed-off-by: Matt Gruskin <matthew.gruskin@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The quirk for the Roland/Cakewalk A-PRO keyboards accidentally used the
wrong interface number, which prevented the driver from attaching to the
device.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: 2.6.37+ <stable@vger.kernel.org>
It looks like MODULE_SUPPORTED_DEVICES() is not implemented yet, but
still, having the entries in the list consistently separated by commas
and with balanced parenthesis won't hurt.
Signed-off-by: Antonio Ospite <ao2@amarulasolutions.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 23caaf19b1 (ALSA: usb-mixer: Add support for Audio Class v2.0)
forgot to adjust the length check for UAC 2.0 feature unit descriptors.
This would make the code abort on encountering a feature unit without
per-channel controls, and thus prevented the driver to work with any
device having such a unit, such as the RME Babyface or Fireface UCX.
Reported-by: Florian Hanisch <fhanisch@uni-potsdam.de>
Tested-by: Matthew Robbetts <wingfeathera@gmail.com>
Tested-by: Michael Beer <beerml@sigma6audio.de>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: 2.6.35+ <stable@vger.kernel.org>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Because currently snd_printd() and snd_printdd() macros are expanded
to empty when CONFIG_SND_DEBUG=n, a compile warning like below
appears sometimes, and we had to covert it by ugly ifdefs:
sound/pci/hda/patch_sigmatel.c: In function ‘stac92hd71bxx_fixup_hp’:
sound/pci/hda/patch_sigmatel.c:2434:24: warning: unused variable ‘spec’ [-Wunused-variable]
For "fixing" these issues better, this patch replaces snd_printd() and
snd_printdd() definitions with empty inline functions instead of
macros. This should have the same effect but shut up warnings like
above.
But since we had already put ifdefs, changing to inline functions
would trigger compile errors. So, such ifdefs is removed in this
patch.
In addition, snd_pci_quirk name field is defined only when
CONFIG_SND_DEBUG_VERBOSE is set, and the reference to it in
snd_printdd() argument triggers the build errors, too. For avoiding
these errors, introduce a new macro snd_pci_quirk_name() that is
defined no matter how the debug option is set.
Reported-by: Stratos Karafotis <stratosk@semaphore.gr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add names of the clock sources for the M-Audio Fast Track
C400.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Attain constant real-world latency by skipping 16 data packets.
The number of packets to be skipped was found by trial and error.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Taking another look at the C400 descriptors, I see now that there is
a clock selector (0x80) for this device.
Right now, the clock source points to the internal clock (0x81), which
is also valid. When the external clock source (0x82) is selected in the
mixer, and the rates mismatch (if it's free-running it is fixed to
48KHz), xruns will occur.
Set the clock ID to the clock selector unit (0x81), which then
allows the validation code to function correctly.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A patch in the 3.2 kernel caused regression with hotplugging the
M-Audio Fast track pro, or sound after suspend. I don't have the
device so I haven't done a full analysis, but it seems userspace
(both udev and pulseaudio) got confused when a card was created,
immediately destroyed, and then created again.
However, at least one person in the bug report (martin djfun)
reports that this patch resolves the issue for him. It also leaves
a message in the log:
"snd-usb-audio: probe of 1-1.1:1.1 failed with error -5" which is
a bit misleading. It is better than non-working audio, but maybe
there's a more elegant solution?
BugLink: https://bugs.launchpad.net/bugs/1095315
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit [0d9741c0: ALSA: usb-audio: sync ep init fix for
audioformat mismatch] introduced the correction of parameters to be
set for sync EP. But since the new code assumes that the sync EP is
always paired with the data EP of another direction, it triggers Oops
when a device only with a single direction is used.
This patch adds a proper check of sync EP type and the presence of the
paired substream for avoiding the crash.
Reported-and-tested-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixes the following sparse warning:
sound/usb/mixer_quirks.c:1209:23: warning:
symbol 'ebox44_table' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch is based on 3.8-rc1. It fixes two things:
1) A kernel panic caused by incorrect allocation of a u8 variable
"bootresponse".
2) A noisy dmesg (urb status -32) caused by broken pipe to an
invalid midi endpoint.
It is also a little cleaner because there is no need for a new
QUIRK_MIDI type as suggested by kernel developers, since the device
follows exactly the MIDIMAN protocol.
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Support the Creative BT-D1 Bluetooth USB audio device. Before this
patch, Linux had trouble finding the correct USB descriptors and bailed
out with these messages:
no or invalid class specific endpoint descriptor
Now it still prints these messages on hotplug:
snd-usb-audio: probe of ...:1.0 failed with error -5
snd-usb-audio: probe of ...:1.2 failed with error -5
snd-usb-audio: probe of ...:1.3 failed with error -5
But the device works correctly, including the HID support.
The patch is diff'ed against 3.8-rc1 but should apply to older kernels
as well.
Signed-off-by: Alexander Schremmer <alex@alexanderweb.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable delay report on capture path. The delay is reset when an
URB is retired and increment at each call to .pointer based
on frame counter changes. The precision of the delay
information is limited to 1ms as in the playback case.
This reverts commit 3f94fad095.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This update contains overall only driver-specific fixes.
Slightly large LOC are seen in usb-audio driver for a couple of new
device quirks and cs42l71 ASoC driver for enhanced features.
The others are a few small (regression) fixes HD-audio, and yet other
small / trival ASoC fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=JoY5
-----END PGP SIGNATURE-----
Merge tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This update contains overall only driver-specific fixes. Slightly
large LOC are seen in usb-audio driver for a couple of new device
quirks and cs42l71 ASoC driver for enhanced features. The others are
a few small (regression) fixes HD-audio, and yet other small / trival
ASoC fixes."
* tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: Support for Digidesign Mbox 2 USB sound card:
ALSA: HDA: Fix sound resume hang
ALSA: hda - bug fix for invalid connection list of Haswell HDMI codec pins
ALSA: hda - Fix the wrong pincaps set in ALC861VD dallas/hp fixup
ALSA: hda - Set codec->single_adc_amp flag for Realtek codecs
ASoC: atmel-ssc: change disable to disable in dts node
ASoC: Prevent pop_wait overwrite
ALSA: usb-audio: ignore-quirk for HP Wireless Audio
ALSA: hda - Always turn on pins for HDMI/DP
ALSA: hda - Fix pin configuration of HP Pavilion dv7
ASoC: core: Fix splitting of log messages
ASoC: cs42l73: Change VSPIN/VSPOUT to VSPINOUT
ASoC: cs42l73: Add DAPM events for power down.
ASoC: cs42l73: Add DMIC's as DAPM inputs.
ASoC: sigmadsp: Fix endianness conversion issue
ASoC: tpa6130a2: Use devm_* APIs
This patch is the result of a lot of trial and error, since there are no specs
available for the device.
Full duplex support is provided, i.e. playback and recording in stereo.
The format is hardcoded at 48000Hz @ 24 bit, which is the maximum that the
device supports. Also, MIDI in and MIDI out both work.
Users will notice that the S/PDIF light also flashes when playback or recording
is active. I believe this means that S/PDIF input/output is simultaneously
activated with the analogue i/o during use.
But this particular functionality remains untested.
Note that this particular version of the patch is so far untested on the
physical hardware because I have not compiled a full kernel with the changes.
However, extensive testing has been done by many users of the hardware
who believe other versions of my patch have worked since circa 2009.
[Modified to make a function static by tiwai]
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As Joe Cooper <swelljoe@gmail.com> reported, "On most HP Envy laptops
the snd-usb-audio module causes the system to become unresponsive and
Gnome Shell 3 to crash.".
See also:
http://mailman.alsa-project.org/pipermail/alsa-devel/2012-December/057729.html
Add a quirk to ignore this device (for now) to solve the instability
issue and allow other USB audio devices to be used.
Reported-by: Joe Cooper <swelljoe@gmail.com>
Tested-by: Isaac Smith <hunternet93@gmail.com>
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull trivial branch from Jiri Kosina:
"Usual stuff -- comment/printk typo fixes, documentation updates, dead
code elimination."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
HOWTO: fix double words typo
x86 mtrr: fix comment typo in mtrr_bp_init
propagate name change to comments in kernel source
doc: Update the name of profiling based on sysfs
treewide: Fix typos in various drivers
treewide: Fix typos in various Kconfig
wireless: mwifiex: Fix typo in wireless/mwifiex driver
messages: i2o: Fix typo in messages/i2o
scripts/kernel-doc: check that non-void fcts describe their return value
Kernel-doc: Convention: Use a "Return" section to describe return values
radeon: Fix typo and copy/paste error in comments
doc: Remove unnecessary declarations from Documentation/accounting/getdelays.c
various: Fix spelling of "asynchronous" in comments.
Fix misspellings of "whether" in comments.
eisa: Fix spelling of "asynchronous".
various: Fix spelling of "registered" in comments.
doc: fix quite a few typos within Documentation
target: iscsi: fix comment typos in target/iscsi drivers
treewide: fix typo of "suport" in various comments and Kconfig
treewide: fix typo of "suppport" in various comments
...
The only required change is to extend the existing Xonar U1
mixer quirks to the U3, which seems to be controlled the same
way.
Signed-off-by: Denis Washington <denisw@online.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The patch below prevents the 6fire usb driver going into panic state
when stopping playing. On some systems the urb in handler
(usb6fire_pcm_in_urb_handler) is being called while urbs are being
killed off, this causes the driver to set panic state and can result in
the kernel warning 'URB %p submitted while active'.
Signed-off-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 947d299686 , "ALSA: snd-usb:
properly initialize the sync endpoint", while correcting the
initialization of the sync endpoint when opening just the data
endpoint, prevents devices that has a sync endpoint, with a channel
number different than that of the data endpoint, from functioning.
Due to a different channel and period bytes count, attempting to
initialize the sync endpoint will fail at the usb host driver.
For example, when using xhci:
cannot submit urb 0, error -90: internal error
With this patch, if a sync endpoint has multiple audioformats, a
matching audioformat is preferred. An audioformat must be found
with at least one channel and support the requested sample rate
and PCM format, otherwise the stream will not be opened.
If the number of channels differ between the selected audioformat
and the requested format, adjust the period bytes count accordingly.
It is safe to perform the calculation on the basis of the channel
count, since the requested PCM audio format and the rate must be
supported by the selected audioformat.
Cc: Jeffrey Barish <jeff_barish@earthlink.net>
Cc: Daniel Mack <zonque@gmail.com>
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit [88a8516a: ALSA: usbaudio: implement USB autosuspend] added
the support of autopm for USB MIDI output, but it didn't take the MIDI
input into account.
This patch adds the following for fixing the autopm:
- Manage the URB start at the first MIDI input stream open, instead of
the time of instance creation
- Move autopm code to the common substream_open()
- Make snd_usbmidi_input_start/_stop() more robust and add the running
state check
Reviewd-by: Clemens Ladisch <clemens@ladisch.de>
Tested-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a similar protection against the disconnection race and the
invalid use of usb instance after disconnection, as well as we've done
for the USB audio PCM.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=51201
Reviewd-by: Clemens Ladisch <clemens@ladisch.de>
Tested-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A lot of headsets/headphones have a "Speaker" mixer control. This confuses
PulseAudio to think it is a speaker instead of a headphone/headset.
Therfore, we rename it to "Headphone".
We determine if something is a headphone similar to how udev determines
form factor (see 78-sound-card.rules).
BugLink: https://bugs.launchpad.net/bugs/1082357
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The playback endpoint uses implicit feedback mode, similar
to the M-Audio FTU. Like with the FTU, we need to associate
the sync pipe ourselves.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add ranges for various Fast Track C400 controls, as observed
while using the vendor's mixer control software (res values
are an estimation).
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Vasily Khoruzhick