Add a lot of N900 nodes
Add OPP table to OMAP5/DRA7
Add support for Newflow NanoBone board
Add i2c aliases
Add McASP and audio support
Add reset/idle on init bindings for OMAP
Add more nodes for AM4272
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=8KX8
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/dt-late' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Some more dts changes from Benoit Cousson <bcousson@baylibre.com> via
Tony Lindgren:
- Add a lot of N900 nodes
- Add OPP table to OMAP5/DRA7
- Add support for Newflow NanoBone board
- Add i2c aliases
- Add McASP and audio support
- Add reset/idle on init bindings for OMAP
- Add more nodes for AM4272
* tag 'omap-for-v3.13/dt-late' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (42 commits)
ARM: dts: omap5-uevm: Remove pinmux for dmic pins
ARM: dts: omap5-uevm: Correct twl6040 reset GPIO pinmux
ARM: dts: TWL4030: Add power button support
ARM: dts: omap3-n900: Add LP5523 support
ARM: dts: omap3-n900: Add TLV320AIC3X support
ARM: dts: omap3-n900:: Mux RX51_LCD_RESET_GPIO in DTS
ARM: dts: omap3-n900: Add NAND support
ARM: dts: omap3-n900: Specify regulator info
ARM: dts: TWL4030: Add missing regulators
ARM: dts: omap3-n900: Add LP5523 support
ARM: dts: omap3-n900: Add vibrator device
ARM: dts: omap3-n900: GPIO key definitions
ARM: dts: omap3-n900: Add support for SD cards
ARM: dts: omap3-n900: Add UART support
ARM: dts: omap3-n900: Fix i2c bus speed
ARM: dts: omap3-n900: Add pinctrl for i2c devices
ARM: dts: DRA7: Add CPU OPP table
ARM: dts: OMAP5: Add CPU OPP table
ARM: dts: dra7-evm: add smps123 supply for CPU
ARM: dts: omap5-uevm: add smps123 supply for CPU
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Move some of the OMAP2+ CM and System Control Module direct
register accesses into CM- and System Control
Module-specific "drivers" underneath arch/arm/mach-omap2/. This
is a prerequisite for moving this code out of arch/arm/mach-omap2/ into
drivers/.
Basic test logs are available here:
http://www.pwsan.com/omap/testlogs/cm_scm_cleanup_a_v3.13/20131019101809/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=L37r
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/cm-scm-cleanup-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Paul Walmsley <paul@pwsan.com> via Tony Lindgren:
Move some of the OMAP2+ CM and System Control Module direct
register accesses into CM- and System Control
Module-specific "drivers" underneath arch/arm/mach-omap2/. This
is a prerequisite for moving this code out of arch/arm/mach-omap2/ into
drivers/.
Basic test logs are available here:
http://www.pwsan.com/omap/testlogs/cm_scm_cleanup_a_v3.13/20131019101809/
* tag 'omap-for-v3.13/cm-scm-cleanup-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3: control: add API for setting IVA bootmode
ARM: OMAP3: CM/control: move CM scratchpad save to CM driver
ARM: OMAP3: McBSP: do not access CM register directly
ARM: OMAP3: clock: add API to enable/disable autoidle for a single clock
ARM: OMAP2: CM/PM: remove direct register accesses outside CM code
+ Linux 3.12-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
* Use macros for mxs pinctrl settings
* New board support: VF610 Cosmic/Cosmic+, imx6q-udoo, MSR M28CU3
* Support DSPI device for vf610
* Add PCIe device for imx6qdl
* Add UHS pinctrl states for imx6sl and imx6qdl
* Display support for APF and imx51-babbage boards
* Enable SPI NOR and USB for imx6sl-evk board
* Enable LVDS for imx6q-sabrelite and SPDIF for imx6qdl-wandboard
* Misc updates on boards: TX28, imx6qdl-wandboard, imx53-qsb etc.
* Some random updates on imx51 device tree
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJSZJgGAAoJEFBXWFqHsHzOskMIALiVd2Cs/Kl4LBufL5JM7JIz
Kh8mW24QmuwoMV0KHGEbzVlZbrIXyQj/8P89AnxaWTBhx9BKTBI1hWPrhCoXEGVQ
mxwpPce9WGiabwR0za9BEYnMOWo4E3s3XAb8rVm5I8d95oe42kCK+yJrhnG+2oQE
Z6+HRfmVTFcXtETcMwggOjgYdV+CRtXiMgoDFiQ10WSrv/9FI9bbS7fEirqEDzaR
4ZkAKNIjbeMYPi0VBbM7bjXezuPUswENyJQQurbCi/h51vpL/oPxEIJKJI3g8Kpi
KLcQu4VAWdzSrrKMdQpVqIcofJLLG5+LJGd7ay8zBGoGgyTtyrAEtwYIjzj/LGE=
=Ya6+
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-3.13' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/dt
From Shawn Guo:
The imx/mxs device tree changes for 3.13:
- Use macros for mxs pinctrl settings
- New board support: VF610 Cosmic/Cosmic+, imx6q-udoo, MSR M28CU3
- Support DSPI device for vf610
- Add PCIe device for imx6qdl
- Add UHS pinctrl states for imx6sl and imx6qdl
- Display support for APF and imx51-babbage boards
- Enable SPI NOR and USB for imx6sl-evk board
- Enable LVDS for imx6q-sabrelite and SPDIF for imx6qdl-wandboard
- Misc updates on boards: TX28, imx6qdl-wandboard, imx53-qsb etc.
- Some random updates on imx51 device tree
* tag 'imx-dt-3.13' of git://git.linaro.org/people/shawnguo/linux-2.6: (44 commits)
ARM: imx: imx6sl iomuxc syscon is compatible to imx6q
ARM: dts: imx6sl-evk: enable the SPI NOR
ARM: dts: imx6sl: add a pinctrl for ECSPI1
ARM: imx27: add missing #pwm-cells property
ARM: dts: imx6sl: add pinctrl uhs states for usdhc
ARM: dts: imx6qdl-sabresd: Add backlight support for lvds
ARM: dts: imx51-babbage: Make DVI and WVGA panel functional
ARM: imx27-apf27dev: Add framebuffer support
ARM: imx51-apf51dev: Add parallel display support
ARM: dts: imx53-qsb: Do not use GPIO1_8 as wakeup source
ARM: dts: imx53-qsb: SDHC1 does not have cd-gpios
ARM: dts: imx53-qsb: SDHC3 is connected in 8-bit mode
ARM: dts: mxs: Add MSR M28CU3 board
ARM: dts: imx6qdl-wandboard: Provide phy-reset-gpios
ARM: dts: imx6qdl-sabresd: Provide phy-reset-gpios
ARM: dts: imx6q-sabrelite: Add ethernet phy reset pin into hog
ARM: dts: imx6qdl: add pcie device node
ARM: dts: imx6q-udoo: Add initial board support
ARM: dts: mxs: Add muxing options for the SSP2 MMC
ARM: dts: add initial VF610 Cosmic/Cosmic+ board support
...
Signed-off-by: Olof Johansson <olof@lixom.net>
* Low-level debug support for Vybrid
* Support soc bus/device for imx6
* Suspend support for imx6dl and imx6sl
* The imx6q clock updates for PCIe and audio PLL support
* IOMUXC GPR update for fec support
* Some random cleanup
* A few defconfig updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJSZI9RAAoJEFBXWFqHsHzOhgkH/RpZ6cvXFFaRdTWQu/SZCXTN
m3Ul0VpuaUp9gsbDNbu//OmqCAsayXaKI7PuJhs885zDKw6R3yMH7hbwXY7z0Qrq
jl9hP1Wzj7oU4CHTQbSDdcO3glUk+jl58a2MrsMsUaXPJTF8iMb8RkatwnReYhiZ
uCBXPwaet7SJTuVQOL1uJmq35LmiROwyAkGsDKnDmphg3ZDUiI9mhqlyOyrS522w
TjmCXrzZQiHkTp12Xo42fIEvE6BF5wCLDlJbq9HRDAlT82CnV62uQC/9os45Hott
H1pJbwdbcdv3+6gUdnWbraukrbhCxT8Yk0As4ljP6YBCxC7Sau+oMh3ii4pvuI0=
=VUrE
-----END PGP SIGNATURE-----
Merge tag 'imx-soc-3.13' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/soc
From Shawn Guo:
The imx/mxs soc changes for 3.13:
* Low-level debug support for Vybrid
* Support soc bus/device for imx6
* Suspend support for imx6dl and imx6sl
* The imx6q clock updates for PCIe and audio PLL support
* IOMUXC GPR update for fec support
* Some random cleanup
* A few defconfig updates
* tag 'imx-soc-3.13' of git://git.linaro.org/people/shawnguo/linux-2.6: (31 commits)
ARM: imx: enable suspend for imx6sl
ARM: imx: ensure dsm_request signal is not asserted when setting LPM
ARM: imx6q: call WB and RBC configuration from imx6q_pm_enter()
ARM: imx6q: move low-power code out of clock driver
ARM: imx: drop extern with function prototypes in common.h
ARM: imx: reset core along with enable/disable operation
ARM: imx: do not return from imx_cpu_die() call
ARM: imx_v6_v7_defconfig: Select CONFIG_PROVE_LOCKING
ARM: imx_v6_v7_defconfig: Enable LEDS_GPIO related options
ARM: mxs_defconfig: Turn off CONFIG_DEBUG_GPIO
ARM: imx: replace imx6q_restart() with mxc_restart()
ARM: mach-imx: mm-imx5: Retrieve iomuxc base address from dt
ARM: mach-imx: mm-imx5: Retrieve tzic base address from dt
ARM: mach-imx: clk-imx51-imx53: Retrieve base address and irq from dt
ARM: mxs_defconfig: Add CHIPIDEA_UDC support
ARM: imx: Include linux/err.h
ARM: imx_v6_v7_defconfig: Add CHIPIDEA_UDC support
ARM: imx_v6_v7_defconfig: Add SPDIF support
ARM: imx6q: clock and Kconfig update for PCIe support
ARM: imx: Add LVDS general-purpose clocks to i.MX6Q
...
Signed-off-by: Olof Johansson <olof@lixom.net>
From Kukjin Kim, these are device-tree updates for Exynos. Among the changes:
- add MIPI PHY node for exynos4
- update regulator for origen and exynos5250-arndale
- add support HDMI for exynos5250, exynos5420
* commit '93457b9cb980ffeeef020c3bcd99065c3807619b':
ARM: dts: Add HDMI related I2C nodes for Arndale board
ARM: dts: enable hdmi subsystem for exynos5420 smdk board
ARM: dts: add dt nodes for hdmi subsystem for exynos5420
ARM: dts: add i2c device nodes for Exynos5420
ARM: dts: add clocks to hdmi dt node for exynos5250
ARM: dts: add mixer clocks to mixer node for Exynos5250
of/documentation: update with clock information for exynos hdmi subsystem
ARM: dts: Disable Exynos5250 I2S controllers by default
ARM: dts: Add reg property to regulator nodes in exynos5250-arndale
ARM: dts: Add fixed voltage regulator to simple bus for origen
ARM: dts: Add MIPI PHY node to exynos4.dtsi
and adding SSP/SPI devices to the device tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=p/3j
-----END PGP SIGNATURE-----
Merge tag 'ux500-dt-for-v3.13-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
From Linus Walleij:
Five incremental device tree patches around the clock handling,
and adding SSP/SPI devices to the device tree.
* tag 'ux500-dt-for-v3.13-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: register all SSP and SPI blocks
ARM: ux500: fix I2C4 clock bit
ARM: ux500: fix clock for GPIO blocks 6 and 7
clk: ux500: fix erroneous bit assignment
ARM: ux500: fix clock for GPIO block 8
Signed-off-by: Olof Johansson <olof@lixom.net>
This DT series sees the introduction of the cubietruck DT, plus the addition of
the i2c controller for the A20 based boards, and of the Security ID found in
all the Allwinner SoCs but the A31.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJSYW3yAAoJEBx+YmzsjxAg5HoP/jCsw/QQ+Po6fvf3h0C1PLQs
JKPredNJwaAjv436zawhlOZWSm6kj0qI6EKshtFUnOm436Ie5vAV/HthlI3vImBs
xtnaCCphfBRB/9MpjOaqQILBMGiVFbI5Rfsx1VgY3lOnLG7yp87PLJ/2d1h+drKF
21LgjkDtc5zP1X+42bNF+oK0UDVkWJUxPxcm5JlwYQUFUBoE/FIqUKU5LM5/fsXE
26eeFPQnf2zqW0Bxx09Jd8wKdRWXLM1+JVlgH+NG2KPL3g5kFbaHHfElzMgsal81
JKk4qmefGcfzLyJAUPTV8B002o4FKGiwaLZdULDVAXFQcJP6AONTCW9cbNAqTZdE
6wSwvo01LOFaAXqJD1HB56ZCASc4qXaoq0vK4Jdefjjb7x4MDeNPD89L6sK21TaQ
atHtFPvzElPyQw5kfJpBypAwSB9+iCk78L7OO2g6bAKvR9WPS2QWr+K7ipuILooT
c9QX9ww9wIMg8whumKsKGkGreSi075FXoSyhF7NEz3TR8P7ghCUdFuK5pdLhiXXi
W/ZejujJDMDjuJtW8VblXFBNa6VrPab51jp5fs+k4IJWDcLbnSpD5PbetMZRNlce
DYAPqhmlx96R2bwzr1Cq+7Ww+7G+xd1HgTh5wZElm2JtBGHVkXOEZbb85stZ5bA8
i4/5xcEPIFExI69Dj9LV
=Qc5W
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-3.13' of https://github.com/mripard/linux into next/dt
From Maxime Ripard:
Allwinner sunXi SoCs device tree changes for 3.13
This DT series sees the introduction of the cubietruck DT, plus the addition of
the i2c controller for the A20 based boards, and of the Security ID found in
all the Allwinner SoCs but the A31.
* tag 'sunxi-dt-for-3.13' of https://github.com/mripard/linux:
ARM: sunxi: dts: Add support for the cubieboard3, the CubieTruck
ARM: sun7i: olinuxino-micro: Enable the I2C controllers
ARM: sun7i: cubieboard2: Enable the I2C controllers
ARM: sun7i: Add the pin muxing options for the I2C controllers
ARM: sun7i: Enable the I2C controllers
ARM: sunxi: dt: Add sunxi-sid to dts for sun4i, sun5i and sun7i
Signed-off-by: Olof Johansson <olof@lixom.net>
There's really only one bugfix in this branch, which is a fix for timers on
the integrator platform. Since Linus Walleij is resurrecting support for
the platform it seems valuable to get the fix into 3.12 even though the
regression has been around a while.
The rest are a handful of maintainers updates. If you prefer to hold those
until 3.13 then just merge the first patch on the branch which is the fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=7MQ0
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"There's really only one bugfix in this branch, which is a fix for
timers on the integrator platform. Since Linus Walleij is
resurrecting support for the platform it seems valuable to get the fix
into 3.12 even though the regression has been around a while.
The rest are a handful of maintainers updates. If you prefer to hold
those until 3.13 then just merge the first patch on the branch which
is the fix"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: Add maintainers entry for Rockchip SoCs
MAINTAINERS: Tegra updates, and driver ownership
MAINTAINERS: ARM: mvebu: add Sebastian Hesselbarth
ARM: integrator: deactivate timer0 on the Integrator/CP
This patch extends the DT selftest code with some test cases for the
interrupt parsing functions.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Conflicts:
drivers/net/usb/qmi_wwan.c
include/net/dst.h
Trivial merge conflicts, both were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The Armada 370/XP SoC has a clock provider called "Core Divider",
that is derived from a fixed 2 GHz PLL clock.
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Armada 370/XP SoCs have a 2 GHz fixed PLL that is used to feed
other clocks. This commit adds a DT representation of this clock
through a fixed-clock compatible node.
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add OPP table to OMAP5/DRA7
Add support for Newflow NanoBone board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=inDp
-----END PGP SIGNATURE-----
Merge tag 'for_3.13_super_late/dts_signed' of git://git.kernel.org/pub/scm/linux/kernel/git/bcousson/linux-omap-dt into omap-for-v3.13/dt
Add a lot of N900 nodes
Add OPP table to OMAP5/DRA7
Add support for Newflow NanoBone board
When the omap5-evm.dts file has been renamed to omap5-uevm.dts and the sEVM
support got deprecated in favor of uEVM (or Panda5) the content was not
validated.
Panda5 does not have support for digital microphones so remove the pinmux
section for it.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
When the omap5-evm.dts file has been renamed to omap5-uevm.dts and the sEVM
support got deprecated in favor of uEVM (or Panda5) the content was not
validated.
On uEVM the twl6040 reset GPIO is from gpio5_141 and not via gpio5_145, which
was the case in sEVM.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
This patch adds support for Nokia N900 TLV320AIC3X chips.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add RX51_LCD_RESET_GPIO pin mux information to
display.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
This patch adds supports for Nokia N900 NAND memory.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add regulator names and voltage information to
the Nokia N900 DTS file.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The twl4030.dtsi is missing some regulators. This patch adds
the missing ones and orders the regulators alphabetically.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add device tree node for the GPIO keys provided by the
N900 board. This is a simple conversion of the existing
board code.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add pin muxing support for the Nokia N900 i2c controllers.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add DT OPP table for DRA7xx family of devices. This data is decoded by
OF with of_init_opp_table() helper function.
The data is based on DRA75x, DRA74x Data Manual revision F (Sept 2013).
TODO: add OPP_HIGH after AVS-Class0 is functional
NOTE: The voltage and frequency values work well only on NOM samples
and it is mandatory to use ABB/AVS Class 0 support for all OPPs.
Clock nodes are pending clock node alignment.
[nm@ti.com: cleanups and rebase to latest]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add DT OPP table for OMAP54xx family of devices. This data is
decoded by OF with of_init_opp_table() helper function.
The data is based on OMAP543x ES2.0 DM Operating Condition Addendum
Version 0.6(April 2013)
NOTE: The voltage and frequency values work well only on NOM samples
and are supposed to work properly only with ABB/AVS for ALL OPPs.
TODO: Add SPEED BIN OPP after ABB and AVS support so the cpufreq works
on all samples seamlessly. Clock node is pending alignment for clock
dts conversion
[nm@ti.com: sync to latest and fixes]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
regulator smps123 supply from Palmas PMIC powers CPU0 on OMAP5uEVM.
Based on a patch by J Keerthy <j-keerthy@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Correct mcspi pin descriptions to match corresponding node name and
add chip select number to be consistent with OMAP5 TRM.
Signed-off-by: Eric Witcher <ewitcher@mindspring.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Control module is not usb specific.
Changes the label to usb_ctrl_mod.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
NanoBone Specification:
-----------------------
CPU:
TI AM335x
Memory:
256MB DDR3
128MB NOR flash
128KB FRAM
Ethernet:
2 x 10/100 connected to SMSC LAN8710 PHY
USB:
1 x USB2.0 Type A
I2C:
2Kbit EEPROM (Microchip 24AA02)
RTC (Maxim DS1338)
GPIO Expander (Microchip MCP23017)
Expansion connector:
6 x UART
1 x MMC/SD
1 x USB2.0
Signed-off-by: Mark Jackson <mpfj@newflow.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Looks like omap3 is still relying on hwmod data for some basic
device tree information. Let's add the information to omap3.dtsi
so we can remove the related hwmod data once omap3 is DT only.
Acked-by: Benoit Cousson <bcousson@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Provide alias to allow ordering the i2c devices correctly.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Currently, on OMAP5, i2c1 and i2c5 defer probe due to pinctrl
dependencies. This changes the i2c ID each bus is registered with in
i2c-dev interface. As a result of this, many userspace tools break and
there is no consistent manner to fix the same if the i2c dev interface
have no consistent numbering.
Since this could happen for other OMAP derivatives, provide i2c alias
for all OMAP3+ SoCs to allow ordering the i2c devices correctly.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add nodes for McASP0 and McASP1 for AM43xx.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add imx6sl support into imx_init_revision_from_anatop(), so that it can
be used to initialize cpu type and revision on imx6sl.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The generic PHY framewrok expects different properties than the
old USB PHY framework. Supply those properties.
Fixes USB OTG port on beagle after the Generic PHY framework was
merged in greg/usb-next. [1]
[1] - https://lkml.org/lkml/2013/9/27/581
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
AM335x EVM-SK have only support for audio playback (stereo jack on the
board) via tlv320aic3106 codec connected to McASP1.
Enable the support for audio playback on the board:
- McASP1 configuration
- tlv320aic3106 configuration
- Machine driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
This patch adds a second tuple to reg property. The new property tuple
describes the memory location for data port registers mapped trough
L3 bus on am33xx. The both property tuples are named accordingly in
the reg-names property.
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
-> Adding pinmux for cpsw, i2c0.
-> Enabling the modules that are present in AM4372 EPOS EVM
These modules are tested on AM4372 EPOS EVM.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Populate nodes for l2-cache-controller, EDMA, mailbox,
mmc, sham.
Update as well DT properties for epwmss, aes, des.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Added dr_mode property in dwc3 and set its default mode to device.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
smps10 should be enabled only in the case of host mode. So stop
doing always_on, boot_on from smps10_out1. The driver will enable
it in host mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Do not reset GPIO1 at boot-up because GPIO 7 in GPIO1 block is used on
OMAP4460 PandaBoard-ES to select voltage register in TPS62361 which
supplies VDD_MPU.
Without this, OMAP4460 PandaBoard-ES boards fail to boot-up because
MPU voltage switches over to VSET0 voltage value (boot voltage) which
is not sufficient to operate the device at OPP100.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Do not reset GPIO0 at boot-up because GPIO0 is used
on AM335x EVM-SK to control VTT regulators on DDR3.
Without this EVM-SK boards fail to boot-up because
of DDR3 corruption.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
On OMAP we have co-processor IPs, memory controllers,
GPIOs which control regulators and power switches to
PMIC, and SoC internal Bus IPs, some or most of which
should either not be reset or idled or both at init.
(In some cases there are erratas which prevent an IP
from being reset)
Have a way to pass this information from DT.
Update the am33xx/omap4 and omap5 dtsi files with the
new bindings for modules which either should not be
idled. reset or both. A later patch would cleanup the
same information that exists today as part of the hwmod
data files.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The generic PHY framewrok expects different properties than the
old USB PHY framework. Supply those properties.
Fixes USB OTG port on GAT04 and N900 after the Generic PHY framework was
merged in greg/usb-next. [1]
[1] - https://lkml.org/lkml/2013/9/27/581
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The arm arch timers frequency are now programmed in the CNTFREQ
per-cpu register by the timer code using the secure API [1].
So remove the redundant entry from the dts.
[1] http://marc.info/?l=linux-omap&m=138139106312786&w=2
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
If we are booting in LE and compiled for BE8, then add code to
set the state to bE8. Since the instruction stream is always LE,
we do not need to do anything special to the instruction.
Also ensure that the secondary processors are started in the same mode.
Note, we do add about 20 bytes to the kernel image, but it seems easier
to do this than adding another configuration to change.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add ARM_BE8() helper to wrap any code conditional on being
compile when CONFIG_ARM_ENDIAN_BE8 is selected and convert
existing places where this is to use it.
Acked-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
omap3 boards.
Note that that these are based on a merge of the
following for the dependencies:
- v3.12-rc5 for fixes to pinctrl mask
- omap-for-v3.13/dt-signed to avoid pointless merge conflicts
- omap-for-v3.13/quirk-signed for legacy pdata handling
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQIcBAABAgAGBQJSYXP6AAoJEBvUPslcq6Vz2fcQAJyOHsHVNs3vxpB2CbFWzgl7
D4tFyL3pHlq9+p/VJwthUoY6WIiWIgEcKoLACD39w+EQ3XThcG1coc0TFj8IPxTr
QOCn5sMu1Z11OKhegcTEhySp8GUrmtNFplMCNK3jPsLjYLdVxOopjziO7qcCd49O
7pjCPfHoU5NkAACcm2nmE2uAlYP4STpGDnzwsi/aHZZQSIni2MslyeN9LeXdwBrN
of29pw8gTA0TVQSXemq0oLnMlEYzLd0ICG2SjSmJ/tWX0vXwjQl4fdDkqHwumPxo
wyjVw744AuXy0WC7PZluQxadd0jEptAs7XSsYgTGOvececWtmZEJDzPGamfabhlX
V6aHIqwVyDOGJXjQkUuaNuD5eO+afDwyaeVOla8YgE9ugwEs3xDXfHdks9nC8n4I
OAk+hXfEBPpLQgItkP+Q3EnYIUJVh4ew5oWCHVfXM8ssKTH6bblWFVtJXP1eyC+0
qkcHOHMR5oK4p+YAmRoRkeMG+Fe2pzT7dWOli4lPVXre1MAd/DQM5+NvgMaveW/E
S8YHj5mRR7a13OAgOWtscjUz+hWE+WIBkCyFuo0w4+RMShKtsiuC+FJirsQpCxLp
aFuwGG8ixT0F4WL/9Ao4iVmIOt15YIW3ND9ubHrPL2Ll0nGPwSmJSb+B7OgSFwqo
G3r4/CSgwljeUq4FZox4
=9Iuv
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/board-removal-signed-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
From Tony Lindgren:
Changes needed to drop legacy booting support for some
omap3 boards.
Note that that these are based on a merge of the
following for the dependencies:
- v3.12-rc5 for fixes to pinctrl mask
- omap-for-v3.13/dt-signed to avoid pointless merge conflicts
- omap-for-v3.13/quirk-signed for legacy pdata handling
* tag 'omap-for-v3.13/board-removal-signed-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (125 commits)
ARM: OMAP2+: remove legacy support for IGEP boards
ARM: OMAP2+: Remove legacy support for zoom platforms
ARM: OMAP2+: Remove legacy booting support for omap3 EVM
ARM: OMAP2: delete board-rm680
ARM: dts: add minimal DT support for Nokia N950 & N9 phones
ARM: dts: Add basic support for zoom3
ARM: dts: Add basic support for TMDSEVM3730 (Mistral AM/DM37x EVM)
ARM: dts: Add common support for omap3-evm
ARM: dts: Shared file for omap GPMC connected smsc911x
+Linux 3.12-rc5
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Add minimal DT support for Nokia N950 & N9 phones. The same functionality
that is provided by the current board file should work: serial console,
USB, OneNAND and MMC.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
I've tested serial, MMC, smsc911x and wl12xx on zoom3. As my
omap is an early ES revision, I have not been able to test
off-idle on this one. But anyways, I'd say we have enough
device tree support for the zoom to be able to drop the
board-zoom files. Patches are welcome to add further features
to this .dts file.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The imx6sl iomuxc syscon is compatible to imx6q, so let's add
compatible string 'fsl,imx6q-iomuxc-gpr' for imx6sl iomuxc syscon node.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
- addition of sound for at91sam9n12
- a little fix for MMC vs. SPI on at91sam9g20ek
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJSYUtRAAoJEAf03oE53VmQH+EH/1YhBDF7uL5s+TCKLBOyau+G
i+W93uG4acZAdbUMRwY+/dP5HMwFu5ZSoKDD5LoRnG2O+jW5dB3rBPi1C42XRKa/
ra1wQcabKFPERJGDJ8DWbuLoJ7WNiDNENDa5ckV3m+F7dRbflcNyUB7vPUiGW78c
xe/WKCKB9Hhpytl1fAynRs+VEu/z3hW7KV7QFyVDatOtV11Vb4QSSJ5HjfMhfito
T7zAsML26hIdcNRsDQs8/4Uwgy8Tevl6FbtLHvht18BJB7FSxRtiPrAGh0KAmwsl
HwIT8RzgJqdDlXTi9z9BdLFlvFZkX83n12jrB7hGScOKav45kvmmC9pgwhFbRzk=
=uw6I
-----END PGP SIGNATURE-----
Merge tag 'at91-dt' of git://github.com/at91linux/linux-at91 into next/dt
From Nicolas Ferre:
First DT series for 3.13
- addition of sound for at91sam9n12
- a little fix for MMC vs. SPI on at91sam9g20ek
* tag 'at91-dt' of git://github.com/at91linux/linux-at91:
ARM: at91: remove pinctrl conflict between mmc and SPI for at91sam9g20ek
ARM: at91: add sound support on at91sam9n12ek board
ARM: at91: enable ssc on at91sam9n12ek board
ARM: at91: enable wm8904 on at91sam9n12ek board
ARM: at91: add ssc dma parameter for at91sam9n12
ARM: at91: add at91sam9n12 ssc clock in look up table
Signed-off-by: Kevin Hilman <khilman@linaro.org>
- a little non-urgent fix
- addition of DT files to MAINTAINERS
- more important, the splitting of .dtsi files
that allows to precisely choose the peripherals
that are present for a particular SoC.
It is useful for upcoming move to common cloks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJSYT2LAAoJEAf03oE53VmQfRMIAIgFQruxaCTlhpvdZaEyDeIK
6+szV0Nn9irQyZqe2HvUR6Flb7FfmAGiyS0xj/OY4bEBbCOeau8Df/op3fVa6+Q2
t510ricL9OWaSqaIsKgJqk3mjpq/7jMrXBQzBjQFgKVcJSA+zOJNiB6qabmE9KjY
z/2+hYaBgG7WwWffHmJQ34NYrIqrWbqaGZczxY9IVw7i4kfDXPL2t2JZk2JTwstt
4C4CRxKXx27EMF0gE2BOgH0r1euaqllSg4ogYlQkBn2canylvNYiRN2Eu36g4peE
cGjtW/8R0ngz3udeoQWeHZ+nZoFT15m048xgIOUbxX5Ocy7u7HSL0tbaH+W9ciI=
=VlMj
-----END PGP SIGNATURE-----
Merge tag 'at91-cleanup' of git://github.com/at91linux/linux-at91 into next/cleanup
From Nicolas Ferre:
First cleanup series for 3.13
- a little non-urgent fix
- addition of DT files to MAINTAINERS
- more important, the splitting of .dtsi files
that allows to precisely choose the peripherals
that are present for a particular SoC.
It is useful for upcoming move to common cloks.
* tag 'at91-cleanup' of git://github.com/at91linux/linux-at91:
MAINTAINERS: Add patterns for DTS files for AT91
ARM: at91: remove init_machine() as default is suitable
ARM: at91/dt: split sama5d3 peripheral definitions
ARM: at91/dt: split sam9x5 peripheral definitions
ARM: at91: cam60: fix incorrect placement of __initdata tag
These MMC and SPI buses can't be configured at the same time because they
share the same traces on the EK board.
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
From Heiko Stübner:
Support for the RK3188 SoC, basic RK3188 based Radxa Rock board
and RK3066a based BQ Curie2 tablet.
* rockchip/boards:
ARM: rockchip: add support for rk3188 and Radxa Rock board
ARM: rockchip: add dts for bqcurie2 tablet
ARM: rockchip: enable arm-global-timer
ARM: rockchip: move shared dt properties to common source file
This adds the SSP and SPI blocks to the device tree and makes
them active. Only this way can their clocks be properly gated
off at boot.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PCLK for I2C4 is controlled by bit 10 in the PCKEN registers
while the KCLK is controlled by bit 9 on the KCKEN, it's
one of these odd assymetric things. Correct the PCLK bit to 10.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The clock assignment in the device tree for GPIO blocks 6
and 7 was incorrect, indicating this was managed by bit 1 on
PRCC 2 while it was in fact bit 11 on PRCC 2.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The clock assignment in the device tree for GPIO block 8 was
incorrect, indicating this was managed by bit 1 on PRCC 6
while it was in fact bit 1 on PRCC 5.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
add a pinctrl for ECSPI1. This pinctrl can be used in the imx6sl-evk board.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The pwm-node is missing its #pwm-cells property. The pwm-framework will
complain about this.
Add the missing property.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
From Stephen Warren:
* tegra/dt:
ARM: tegra: Use symbolic names for gr3d clocks
ARM: tegra: Mark Tegra30 display controller compatible with Tegra20
ARM: tegra: add GPIO controller to tegra124.dtsi
ARM: tegra: enable LP1 suspend mode for Venice2
ARM: tegra: enable Tegra RTC as default for Tegra124
ARM: tegra: add Venice2 board support
ARM: tegra: Add initial device tree for Tegra124
ARM: tegra: add vcc supply for nct1008 to Cardhu
ARM: tegra: add DT entry for nct1008 to Dalmore
ARM: tegra: use dt-binding header for key code
ARM: tegra: add palmas pincontrol to Dalmore device tree
Signed-off-by: Kevin Hilman <khilman@linaro.org>
- convert Calxeda cpuidle driver to a platform driver and to use PSCI
- convert highbank smp_ops and suspend to PSCI
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJSYCG/AAoJEMhvYp4jgsXiFkkIALhWCtYC7qcthorB/s9STVkv
5VhPA7Jx9i9omnrsdzICXYC/HQaSN7gwgAPICYxTcAcen+qySHeXvk7jWh7PtQJ9
OHLWd1tYVxLV1y9tnmiFYVbJn017W0Kq0m4kkZEh6Q8KW0qE1xcHGREWHs/+1D4k
Rx798Tg6jgjt0nvg893aAcFQsgKxG53n5uqNySI9DKvxYcJBJkHD0/EgyHk+myVY
TPZj6f9xGwLCv0rQU6Vr29NniX1w2bRt6lYEp0KGlGjEGbiuStcRf6xUUmhxmDCs
faIspFMxpR4dqqeIq1Xh2x8S4QOMjDoiFGZmGBgrNdvLNOGNsd+QRhdLJiXuB88=
=8WVt
-----END PGP SIGNATURE-----
Merge tag 'highbank-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux into next/soc
From Rob Herring:
Highbank platform updates for 3.13
- convert Calxeda cpuidle driver to a platform driver and to use PSCI
- convert highbank smp_ops and suspend to PSCI
* tag 'highbank-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dts: calxeda: add ARM PSCI binding
ARM: highbank: adapt to use ARM PSCI calls
ARM: PSCI: remove unnecessary include of arm-gic.h
cpuidle: calxeda: add support to use PSCI calls
ARM: highbank: cpuidle: convert to platform driver
cpuidle: calxeda: add cpu_pm_enter/exit calls
- dove
- add audio devices
- fix bad properties of si5351 clkout2 for CuBox
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJSX+yTAAoJEAi3KVZQDZAev1wIAJA521UnQR6efGNEU6wD3Yvq
hjXEe+Da62FG2YUzZhOpLYIRrc0EvTrt/JIAbLbf5qrOnc9kzO6YdZVnRJJgWDP0
Qzak9C0xqfsFeR7MxnDuyJ10/TYgM1iugvUcs6tqRDb7LdqcGBv92vv8zCdieiiJ
XNtA56GVvEXo6LKp4KjC/dNv4vQBPEzDukSm81g/dfVDIhm7vbGMeNpFtHPHcNQa
lASc6NjYzZXBZlz/ckRIZeT+MePpPkWusb8DOtLkv6/pRJjtSLaQqSLR82l52U+E
eVb9SoQJWjxmrVLMEk3nUYvsWVgLtClND62snfpu+JP5ELb+DBwky4DzVvftpaY=
=P7l9
-----END PGP SIGNATURE-----
Merge tag 'dt-3.13-3' of git://git.infradead.org/linux-mvebu into next/dt
From Jason Cooper:
mvebu dt changes for v3.13 (round 3)
- dove
- add audio devices
- fix bad properties of si5351 clkout2 for CuBox
* tag 'dt-3.13-3' of git://git.infradead.org/linux-mvebu:
ARM: Dove: fix bad properties of the si5351 clkout2 used by Cubox audio
ARM: Dove: Add the audio device to the Cubox DT
ARM: Dove: Add the audio devices in DT
Some small cleanups for MSM. Removes extraneous irq definitions that
aren't used on DT targets, moves the single existing board file to
board-dt.c in antipication of additional targets, and renames the
existing DT files to have a common 'qcom' prefix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=xAJK
-----END PGP SIGNATURE-----
Merge tag 'msm-cleanup-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm into next/cleanup
From David Brown:
General cleanups for MSM for 3.13
Some small cleanups for MSM. Removes extraneous irq definitions that
aren't used on DT targets, moves the single existing board file to
board-dt.c in antipication of additional targets, and renames the
existing DT files to have a common 'qcom' prefix.
* tag 'msm-cleanup-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
ARM: msm: Rename msm devicetrees to have standard 'qcom' prefix
ARM: msm: Create a common board-dt and config ARCH_MSM_DT
ARM: msm: Remove irqs-*.h files for DT based targets
Signed-off-by: Kevin Hilman <khilman@linaro.org>
- Fix up the LED support
- Update the Integrator defconfig
- Remove ATAG boot path
- Move some stuff over to the device tree
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=p2Z9
-----END PGP SIGNATURE-----
Merge tag 'integrator-for-v3.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/soc
From Linus Walleij:
Integrator patches for the v3.13 kernel cycle:
- Fix up the LED support
- Update the Integrator defconfig
- Remove ATAG boot path
- Move some stuff over to the device tree
* tag 'integrator-for-v3.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: integrator: core module registers from compatible strings
ARM: integrator: use devm_ioremap() to remap CM
cpufreq: probe the Integrator cpufreq driver from DT
ARM: integrator: move CM base into device tree
ARM: integrator: decommission the <mach/irqs.h> header
ARM: integrator: delete non-devicetree boot path
ARM: integrator: print the Linux IRQ in LL_DEBUG code
ARM: integrator: get the LM interrupts from DT
ARM: integrator: update defconfig
ARM: integrator: get the CM control register by proxy
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Commit 05849c9381 (ARM: tegra30: convert
device tree files to use CLK defines) updated the Tegra30 device tree to
use symbolic clock names but forgot to update this node.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The display controller found on Tegra30 SoCs is backwards-compatible
with the one on Tegra20 SoCs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch splits the sama5d3 SoCs definition:
- a common base for all sama5d3 SoCs (sama5d3.dtsi)
- several optional peripheral definitions which will be included by sama5d3
specific SoCs (sama5d3_'periph name'.dtsi)
- sama5d3 specific SoC definitions (sama5d3x.dtsi)
This provides a better representation of the real hardware (drop unneed
dt nodes) and avoids peripheral id conflict (which is not the case for
current sama5d3 SoCs, but could be if other SoCs of this family are
released).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
[nicolas.ferre@atmel.com: add more "sama5d3?" compatibility strings]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch splits the sam9x5 peripheral definitions into:
- a common base for all sam9x5 SoCs (at91sam9x5.dtsi)
- several optional peripheral definitions which will be included by specific
sam9x5 SoCs (at91sam9x5_'periph name'.dtsi)
This provides a better representation of the real hardware (drop unneeded
dt nodes) and avoids future peripheral id conflict (lcdc and isi both use
peripheral id 25).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This augments the core machine code for the Integrator platforms
to get their references to the core module device nodes by
using compatible strings instead of predefined node names
and rename the CP syscon node to be simply "syscon".
Reported-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the core module (CM) control base into the device
tree. It is a simple memory range of 0x200 bytes. Move the
cm header down into the machine directory and unexport the
cm_control() symbol as no modules are using it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The OF/DT boot path needs to get the LM (Logical Module)
IRQs from the device tree for coherency. This augments the
DT syscon node to contain these IRQs and alter the DT LM
code to get them from there.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Revision 0 of Exynos4210 SoC (used on Universal C210 board) requires
'secure' PL330 MDMA1 address (0x12840000) instead of 'non-secure' one
(0x12850000). Fix it by overriding the default PL330 MDMA1 address in
exynos4210-universal_c210.dts.
This is a Device Tree (DT) version of commit 91280e7 ("ARM: EXYNOS:
PL330 MDMA1 fix for revision 0 of Exynos4210 SOC") and fixes recent
regression caused by conversion to DT-only setup on ARM EXYNOS.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Exynos cpufreq drivers does not support device tree based regulator
lookup, so it can get the VDD ARM regulator only by its name. To get
cpufreq working for now, this patch works this around by renaming the
regulator in board dts files to vdd_arm, which is the name expected by
the driver.
This fixes a regression introduced by dropping support of board file
based bootup of Exynos 4210 boards that rendered cpufreq inoperable on
Trats and Origen boards.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch removes '_' from "early_prink" on Exynos5440 dts
files in according to kernel-parameters document.
Signed-off-by: Youngmin Nam <youngmin.nam@samsung.com>
Reviewed-by: Sachin Kamat <sachin.kamat@linaro.org>
Tested-by: Jungseok Lee <jays.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Corrects an obvious typo in the Arndale pinctrl descriptions in DT.
The samsung-pinctrl driver uses the correct name.
Signed-off-by: Al Stone <al.stone@linaro.org>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The Tegra124 GPIO controller is identical to Tegra30, so copy the
DT node from tegra30.dtsi to tegra124.dtsi.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
n900 secure mode changes. Note that the n900 secure mode changes
will still be needed for device tree based booting also.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=WRd/
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/board-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/boards
From Tony Lindgren:
Platform data changes for omaps for the display subsystem and
n900 secure mode changes. Note that the n900 secure mode changes
will still be needed for device tree based booting also.
* tag 'omap-for-v3.13/board-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (508 commits)
ARM: OMAP2+: display: Create omap_vout device inside omap_display_init
ARM: OMAP2+: display: Create omapvrfb and omapfb devices inside omap_display_init
ARM: OMAP2+: display: Create omapdrm device inside omap_display_init
ARM: OMAP2+: drm: Don't build device for DMM
RX-51: Add support for OMAP3 ROM Random Number Generator
ARM: OMAP3: RX-51: ARM errata 430973 workaround
ARM: OMAP3: Add secure function omap_smc3() which calling instruction smc #1
+Linux 3.12-rc4
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Add the minimal DTS support for DRA7xx based SoC core.
Add the initial support for N900 and gta04 phones.
Enable USB3 on OMAP5 evm board.
Add support for cryto accelerators
Add new IGEP AQUILA board
Add AM33XX EDMA support
Update HSUSB node to use the reset-gpios fmwk
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=808Q
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
From Tony Lindgren:
omap device tree related changes via Benoit Cousson <bcousson@baylibre.com>:
Add the minimal DTS support for DRA7xx based SoC core.
Add the initial support for N900 and gta04 phones.
Enable USB3 on OMAP5 evm board.
Add support for cryto accelerators
Add new IGEP AQUILA board
Add AM33XX EDMA support
Update HSUSB node to use the reset-gpios fmwk
* tag 'omap-for-v3.13/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (58 commits)
ARM: dts: dra7-evm: Add mmc2 node for eMMC support
ARM: dts: dra7-evm: Add mmc1 node for micro-sd support
ARM: dts: omap5-uevm: mark TWL6037 as system-power-controller
ARM: dts: omap3-igep0020: use standard constant for IRQ flags
ARM: dts: omap3-igep0020: Add HS USB Host support
ARM: dts: omap3-igep: Add USB OTG support
ARM: dts: AM33XX beagle black: add pinmux and hdmi node to enable display
ARM: dts: AM33XX: Add LCDC info into am335x-evm
ARM: dts: AM437X: Add DES node
ARM: dts: AM437X: Add AES node
ARM: dts: AM33XX: Fix AES interrupt number
ARM: dts: AM33XX: Add AES data and documentation
ARM: dts: AM33XX: Add SHAM data and documentation
ARM: dts: OMAP4: Add DES3DES node
ARM: dts: OMAP4: Add AES node
ARM: dts: am335x-evm[sdk]: switch mmc1 to 4-bit mode
ARM: dts: am335x-bone-common: correct mux mode for cmd line
ARM: dts: AM33XX: Add support for IGEP AQUILA EXPANSION board.
ARM: dts: AM33XX: Add support for IGEP COM AQUILA
ARM: dts: am335x-boneblack: move fixed regulator to board level
...
Signed-off-by: Kevin Hilman <khilman@linaro.org>
- Always build in board-generic, and add pdata quirks and auxdata
support for it so we have all the pdata related quirks
in the same place.
- Merge of the drivers/pinctrl changes that are needed for PM
to continue working on omap3 and also needed for other omaps
eventually. The three pinctrl related patches have been acked
by Linus Walleij and are pulled into both the pinctrl tree
and this branch.
- Few defconfig related changes for drivers needed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=bqsS
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/quirk-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
From Tony Lindgren:
Changes needed to prepare for making omap3 device tree only:
- Always build in board-generic, and add pdata quirks and auxdata
support for it so we have all the pdata related quirks
in the same place.
- Merge of the drivers/pinctrl changes that are needed for PM
to continue working on omap3 and also needed for other omaps
eventually. The three pinctrl related patches have been acked
by Linus Walleij and are pulled into both the pinctrl tree
and this branch.
- Few defconfig related changes for drivers needed.
* tag 'omap-for-v3.13/quirk-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (523 commits)
ARM: configs: omap2plus_defconfig: enable dwc3 and dependencies
ARM: OMAP2+: Add WLAN modules and of_serial to omap2plus_defconfig
ARM: OMAP2+: Run make savedefconfig on omap2plus_defconfig to shrink it
ARM: OMAP2+: Add minimal 8250 support for GPMC
ARM: OMAP2+: Use pdata quirks for wl12xx for omap3 evm and zoom3
ARM: OMAP: Move DT wake-up event handling over to use pinctrl-single-omap
ARM: OMAP2+: Add support for auxdata
pinctrl: single: Add support for auxdata
pinctrl: single: Add support for wake-up interrupts
pinctrl: single: Prepare for supporting SoC specific features
ARM: OMAP2+: igep0020: use display init from dss-common
ARM: OMAP2+: pdata-quirks: add legacy display init for IGEPv2 board
+Linux 3.12-rc4
Signed-off-by: Kevin Hilman <khilman@linaro.org>
* Does not include any new bindings or bindings change
* Add dts file for a SOCFPGA with an Arria V FPGA
* Add a clocks property for the TWD timer
* Add support for Terasic SocKit Board which has Cyclone5 FPGA
* From Steffen Trumtrar:
"This series includes some minor cleanups (indentation and clock labels) and
reorders the socfpga dts hierarchy from:
socfpga.dtsi
-> socfpga_$board.dts
-> socfpga_$otherboard.dts
to
socfpga.dtsi
-> socfpga_cyclone5.dtsi
--> socfpga_cyclone5_$board.dts
--> socfpga_cyclone5_$otherboard.dts
"
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=jmLh
-----END PGP SIGNATURE-----
Merge tag 'socfpga-dts-updates-for-v3.13' of git://git.rocketboards.org/linux-socfpga-next into next/dt
From Dinh Nguyen:
Updates to dts file structure for Altera's SOCFPGA
* Does not include any new bindings or bindings change
* Add dts file for a SOCFPGA with an Arria V FPGA
* Add a clocks property for the TWD timer
* Add support for Terasic SocKit Board which has Cyclone5 FPGA
* From Steffen Trumtrar:
"This series includes some minor cleanups (indentation and clock labels) and
reorders the socfpga dts hierarchy from:
socfpga.dtsi
-> socfpga_$board.dts
-> socfpga_$otherboard.dts
to
socfpga.dtsi
-> socfpga_cyclone5.dtsi
--> socfpga_cyclone5_$board.dts
--> socfpga_cyclone5_$otherboard.dts
"
* tag 'socfpga-dts-updates-for-v3.13' of git://git.rocketboards.org/linux-socfpga-next:
dts: socfpga: Add support for Altera's SOCFPGA Arria V board
ARM: socfpga: dts: fix s2f_* clock name
ARM: socfpga: dts: cleanup indentation
ARM: socfpga: dts: Add support for terasic SoCkit
ARM: socfpga: dts: Move common nodes to cyclone5 dtsi
arm: socfpga: Add clock for smp_twd timer
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Basic devicetree files for the rk3188 SoC. Also provided is a board
dts file for the upcoming Radxa Rock board using this SoC.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Olof Johansson