No functional change, De Morgan !(A && B) = (!A || !B)
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a URB is killed while the host is removed we can end up in a situation
where the hub thread takes the roothub device lock, and waits for
the URB to be given back by xhci-hcd, blocking the host remove code.
xhci-hcd tries to stop the endpoint and give back the urb, but can't
as the host is removed from PCI bus at the same time, preventing the normal
way of giving back urb.
Instead we need to rely on the stop command timeout function to give back
the urb. This xhci_stop_endpoint_command_watchdog() timeout function
used a XHCI_STATE_DYING flag to indicate if the timeout function is already
running, but later this flag has been taking into use in other places to
mark that xhci is dying.
Remove checks for XHCI_STATE_DYING in xhci_urb_dequeue. We are still
checking that reading from pci state does not return 0xffffffff or that
host is not halted before trying to stop the endpoint.
This whole area of stopping endpoints, giving back URBs, and the wathdog
timeout need rework, this fix focuses on solving a specific deadlock
issue that we can then send to stable before any major rework.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stop Endpoint command can come at any point and we
have no control of that. We should make sure to
handle COMP_STOP on SETUP phase as well, otherwise
urb->actual_length might be set to negative values
in some occasions such as below:
urb->length = 4;
build_control_transfer_td_for(urb, ep);
stop_endpoint(ep);
COMP_STOP:
[...]
urb->actual_length = urb->length - trb->length;
trb->length is 8 for SETUP stage (8 control request
bytes), so actual_length would be set to -4 in this
case.
While doing that, also make sure to use TRB_TYPE
field of the actual TRB instead of matching pointers
to figure out in which stage of the control transfer
we got our completion event.
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current abort operation has race.
xhci_handle_command_timeout()
xhci_abort_cmd_ring()
xhci_write_64(CMD_RING_ABORT)
xhci_handshake(5s)
do {
check CMD_RING_RUNNING
udelay(1)
...
COMP_CMD_ABORT event
COMP_CMD_STOP event
xhci_handle_stopped_cmd_ring()
restart cmd_ring
CMD_RING_RUNNING become 1 again
} while ()
return -ETIMEDOUT
xhci_write_64(CMD_RING_ABORT)
/* can abort random command */
To do abort operation correctly, we have to wait both of COMP_CMD_STOP
event and negation of CMD_RING_RUNNING.
But like above, while timeout handler is waiting negation of
CMD_RING_RUNNING, event handler can restart cmd_ring. So timeout
handler never be notice negation of CMD_RING_RUNNING, and retry of
CMD_RING_ABORT can abort random command (BTW, I guess retry of
CMD_RING_ABORT was workaround of this race).
To fix this race, this moves xhci_handle_stopped_cmd_ring() to
xhci_abort_cmd_ring(). And timeout handler waits COMP_CMD_STOP event.
At this point, timeout handler is owner of cmd_ring, and safely
restart cmd_ring by using xhci_handle_stopped_cmd_ring().
[FWIW, as bonus, this way would be easily extend to add CMD_RING_PAUSE
operation]
[locks edited as patch is rebased on other locking fixes -Mathias]
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is preparation to fix abort operation race (See "xhci: Fix race
related to abort operation"). To make timeout sleepable, use
delayed_work instead of timer.
[change a newly added pending timer fix to pending work -Mathias]
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In command timer function, xhci_handle_command_timeout(), xhci->lock
is unlocked before call into xhci_abort_cmd_ring(). This might cause
race between the timer function and the event handler.
The xhci_abort_cmd_ring() function sets the CMD_RING_ABORT bit in the
command register and polling it until the setting takes effect. A stop
command ring event might be handled between writing the abort bit and
polling for it. The event handler will restart the command ring, which
causes the failure of polling, and we ever believed that we failed to
stop it.
As a bonus, this also fixes some issues of calling functions without
locking in xhci_handle_command_timeout().
Cc: <stable@vger.kernel.org> # 3.7+
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we get a command completion event at the same time as the command
timeout work starts on another cpu we might end up aborting the wrong
command.
If the command completion takes the xhci lock before the timeout work, it
will handle the command, pick the next command, mark it as current_cmd, and
re-queue the timeout work. When the timeout work finally gets the lock
It will start aborting the wrong command.
This case can be resolved by checking if the timeout work is pending inside
the timeout function itself. A new timeout work can only be pending if the
command completed and a new command was queued.
If there are no more commands pending then command completion will set
the current_cmd to NULL, which is already handled in the timeout work.
Cc: <stable@vger.kernel.org>
Reported-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When current command was supposed to be aborted, host will free the command
in handle_cmd_completion() function. But it might be still referenced by
xhci->current_cmd, which need to set NULL.
Cc: <stable@vger.kernel.org>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
handle_cmd_completion() frees a command structure which might be still
referenced by xhci->current_cmd.
This might cause problem when xhci->current_cmd is accessed after that.
A real-life case could be like this. The host takes a very long time to
respond to a command, and the command timer is fired at the same time
when the command completion event arrives. The command completion
handler frees xhci->current_cmd before the timer function can grab
xhci->lock. Afterward, timer function grabs the lock and go ahead with
checking and setting members of xhci->current_cmd.
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One big merge this time with a total of 166 non-merge commits.
Most of the work, by far, is on dwc2 this time (68.2%) with dwc3 a far
second (22.5%). The remaining 9.3% are scattered on gadget drivers.
The most important changes for dwc2 are the peripheral side DMA support
implemented by Synopsys folks and support for the new IOT dwc2
compatible core from Synopsys.
In dwc3 land we have support for high-bandwidth, high-speed isochronous
endpoints and some non-critical fixes for large scatter lists.
Apart from these, we have our usual set of cleanups, non-critical fixes,
etc.
-----BEGIN PGP SIGNATURE-----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=5WN9
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.10 merge window
One big merge this time with a total of 166 non-merge commits.
Most of the work, by far, is on dwc2 this time (68.2%) with dwc3 a far
second (22.5%). The remaining 9.3% are scattered on gadget drivers.
The most important changes for dwc2 are the peripheral side DMA support
implemented by Synopsys folks and support for the new IOT dwc2
compatible core from Synopsys.
In dwc3 land we have support for high-bandwidth, high-speed isochronous
endpoints and some non-critical fixes for large scatter lists.
Apart from these, we have our usual set of cleanups, non-critical fixes,
etc.
xhci->slot_id is used for providing a way to pass slot id from the
command completion handler to the function waiting for completion.
It's shared by enumerations of all USB devices connected to an
xhci host. Hence, it's a source for possible races. Since we've
introduced command structure and the command queue to xhci driver.
It's better to move slot_id from xhci_hcd structure to xhci_command
structure. Hence the race source is removed.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
define GET_EP_CTX_STATE() macro to get the endpoint state from a
pointer to a le32 enpoint context structure
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In xhci_handle_event(), when errors are detected, driver always sets
a bit in error_bitmask (one member of the xhci private driver data).
That means users have to retrieve and decode the value of error_bitmask
in xhci private driver data if they want to know whether those erros
ever happened in xhci_handle_event(). Otherwise, those errors are just
ignored silently.
This patch cleans up this by replacing the setting of error_bitmask
with the kernel print functions, so that users can easily check and
report the errors happened in xhci_handle_event().
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want one function that gives back urb in interrupt that can
be used in both normal cases and when killing off urbs.
Add small helpers that check if td is last_td_in_urb() and
that increase the td count of a urb inc_td_cnt()
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mostly refactoring and code cleanup.
while handling transfer events we used to check the return value of
various functions to see if we can give back the URB.
Turns out the only case when those return values are set are when
finish_td() notices we are completing the last td in the URB.
give back the urb directly in finish_td() instead.
Only functional change is that we now increase the event ring dequeue
pointer in sowtware after giving back the URB. This should not matter
as we are in hardware interrupt context and the time when writing the
new event ring dequeue to hardware remains the same.
Hardware is the only one that can put event TRBs on the event ring.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move giving back the urb to a separate function
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following sparse warning:
drivers/usb/host/xhci-ring.c:608:6: warning:
symbol 'xhci_unmap_td_bounce_buffer' was not declared.
Should it be static?
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No functional changes but a few debugging outputs removed
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Renaming variables, no functional changes
Event trbs on the event ring cointain a pointer to the transfer trb
on a endpoint ring that caused the event.
The naming has been very confusing as the event trb was called "event"
and the endpoint transfer trb was called "event_trb".
rename all variables that are realated to the endpoint transfer trb
from event_* to ep_*
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mostly refactoring, but does also change error message if
we get a bad length in the event trb.
Adds a helper function to sum trb lengths of partial TDs
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor pricess_ctrl_tx() to make it more readable
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We only check for the URB_SHORT_NOT_OK urb flag to set the urb status
to -EREMOTEIO for transfers that didn't transfer all data.
This will be done in __usb_hcd_giveback() for other than isoc tranfers,
so remove the redundant check from xhci.
Also fix a couple split lines in debug messages to make them greppable.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
replace the complex check for noop with a simple helper
Improve code readability
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the trb_is_link() and link_trb_toggles_cycle() helpers to
make the code more readable
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fist function called in xhci_halt is xhci_quiesce, so no point
in calling it twice
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_endpoint_maxp() is now returning maxpacket
correctly - iow only bits 10:0. We can finaly remove
XHCI's private GET_MAX_PACKET macro.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The stop endpoint command has its own 5 second timeout timer.
If the timeout function is triggered between USB3 and USB2 host
removal it will try to call usb_hc_died(xhci_to_hcd(xhci)->primary_hcd)
the ->primary_hcd will be set to NULL at USB3 hcd removal.
Fix this by first checking if the PCI host is being removed, and
also by using only xhci_to_hcd() as it will always return the primary
hcd.
CC: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enqueue the first TRB even if full_len is zero.
Without this "adb install <apk>" freezes the system.
Signed-off-by: Alban Browaeys <alban.browaeys@gmail.com>
Fixes: 86065c2719 ("xhci: don't rely on precalculated value of needed trbs in the enqueue loop")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix "Command completion event does not match command" errors by always
handling the command ring stopped events.
The command ring stopped event is generated as a result of aborting
or stopping the command ring with a register write. It is not caused
by a command in the command queue, and thus won't have a matching command
in the comman list.
Solve it by handling the command ring stopped event before checking for a
matching command.
In most command time out cases we abort the command ring, and get
a command ring stopped event. The events command pointer will point at
the current command ring dequeue, which in most cases matches the timed
out command in the command list, and no error messages are seen.
If we instead get a command aborted event before the command ring stopped
event, the abort event will increse the command ring dequeue pointer, and
the following command ring stopped events command pointer will point at the
next, not yet queued command. This case triggered the error message
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gcc warns about what first looks like a reference to an uninitialized
variable:
drivers/usb/host/xhci-ring.c: In function 'handle_cmd_completion':
drivers/usb/host/xhci-ring.c:753:4: error: 'ep_ring' may be used uninitialized in this function [-Werror=maybe-uninitialized]
xhci_unmap_td_bounce_buffer(xhci, ep_ring, cur_td);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/usb/host/xhci-ring.c:647:20: note: 'ep_ring' was declared here
struct xhci_ring *ep_ring;
^~~~~~~
It's clear to see that the list_empty() check means it can never be
uninitialized, however it still looks wrong:
When ep->cancelled_td_list contains more than one entry, the
ep_ring variable will point to the ring that was retrieved
from the last urb, and we have to look it up again in the
second loop instead, which fixes the behavior and gets rid of the
warning too.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: f9c589e142 ("xhci: TD-fragment, align the unsplittable case with a bounce buffer")
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's only used with rings that have link trbs
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only used in one place, replace with trb_is_link() helper
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
inc_deq() is called both for rings with link trbs and the event ring
without link trbs.
The last_trb() check in inc_deq() has a off by one error, going beyond
allocated array when checking if trb == [TRBS_PER_SEGMENT], and the whole
inc_deq() depend on this.
Rewrite the inc_deq() funciton, remove the faulty last_trb() helper, add
new last_trb_on_seg() and last_trb_on_ring() helpers
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new is_link_trb() function that only checks for link trbs.
We want to split generic last_trb() function which is used for both
event rings without link trbs, and endpoint and command rings with links.
This will allow us to easier check for link trbs added mid segments.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the event ring related checks in inc_enq()
Host hardware is the producer of events on the event ring,
driver will not queue anything, or call inc_enq() for the
event ring.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the last trb before a link is not packet size aligned, and is not
splittable then use a bounce buffer for that chunk of max packet size
unalignable data.
Allocate a max packet size bounce buffer for every segment of a bulk
endpoint ring at the same time as allocating the ring.
If we need to align the data before the link trb in that segment then
copy the data to the segment bounce buffer, dma map it, and enqueue it.
Once the td finishes, or is cancelled, unmap it.
For in transfers we need to first map the bounce buffer, then queue it,
after it finishes, copy the bounce buffer to the original sg list, and
finally unmap it
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TD fragments section 4.11.7.1 in xhci specs have additional requirements
on how trbs in TDs must be organized.
TD fragments shall not span transfer ring segments and TD fragments must
be packet aligned. Normally we don't care about TD fragments, on TD is one
big fragment, but if a TD spans ring segments it will be treated as two
fragments, and we need to comply with the alignment requirements.
For us this means that the payload data must be packet aligned in the
last trb before a link trb.
In most mass storage bulk tranfers we are lucky as the block size aligns
nicely with packet size, and there are no issues.
However, usb network adapters using scatterlists can hit this alignment
issue, and usbtest in kernel triggers this in minutes.
This patch is a partial solution, it solves the easy case when the last
trb before the link trb contains a packet boundary.
If that is the case then just split the trb at the boundary.
If not, then just print a debug message and continue as we have always
done, hoping for the best
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Queue trbs until all payload data in the urb is tranferred.
The actual number of trbs might need to change from the pre-calculated
number when the packet alignment restrictions for td fragments in
xhci 4.11.7.1 are taken into account.
Long term plan is to get rid of calculating the needed trbs in advance
all together. It's an unnecessary extra walk through the scatterlist.
This change also allows some bulk queue function simplifications
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We only need to know if we are queuing the last trb for a TD when
calculating the td remainder field.
The total number of trbs left is not used.
We won't be able to trust the pre-calculated number of trbs used if we
need to align trb data by splitting or merging trbs in order to satisfy
comply with data alignment requirements in xhci specs section 4.11.7.1.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a zero-length packet is needed after a bulk transfer, then an
additional zero length TD was prepared before enqueueing the bulk transfer
This set up the zero packet TD structure with incorrect td->start_seg
and td->first_trb pointers.
Prepare the zero packet TD after the data bulk TD is enqueued instead.
It sets these pointers correctly.
This change also simplifies unnecessary complexity related to keeping
track of the last trb when enqueuing trbs.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tiny change, a bit more readable.
The real reason for this change is that the coming td fragment work
had several over 80 lines character lines split just because of a few
extra characters in variable names.
no functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If commands timeout we mark them for abortion, then stop the command
ring, and turn the commands to no-ops and finally restart the command
ring.
If the host is working properly the no-op commands will finish and
pending completions are called.
If we notice the host is failing, driver clears the command ring and
completes, deletes and frees all pending commands.
There are two separate cases reported where host is believed to work
properly but is not. In the first case we successfully stop the ring
but no abort or stop command ring event is ever sent and host locks up.
The second case is if a host is removed, command times out and driver
believes the ring is stopped, and assumes it will be restarted, but
actually ends up timing out on the same command forever.
If one of the pending commands has the xhci->mutex held it will block
xhci_stop() in the remove codepath which otherwise would cleanup pending
commands.
Add a check that clears all pending commands in case host is removed,
or we are stuck timing out on the same command. Also restart the
command timeout timer when stopping the command ring to ensure we
recive an ring stop/abort event.
Cc: stable <stable@vger.kernel.org>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Under stress occasions some TI devices might not return early when
reading the status register during the quirk invocation of xhci_irq made
by usb_hcd_pci_remove. This means that instead of returning, we end up
handling this interruption in the middle of a shutdown. Since
xhci->event_ring has already been freed in xhci_mem_cleanup, we end up
accessing freed memory, causing the Oops below.
commit 8c24d6d7b0 ("usb: xhci: stop everything on the first call to
xhci_stop") is the one that changed the instant in which we clean up the
event queue when stopping a device. Before, we didn't call
xhci_mem_cleanup at the first time xhci_stop is executed (for the shared
HCD), instead, we only did it after the invocation for the primary HCD,
much later at the removal path. The code flow for this oops looks like
this:
xhci_pci_remove()
usb_remove_hcd(xhci->shared)
xhci_stop(xhci->shared)
xhci_halt()
xhci_mem_cleanup(xhci); // Free the event_queue
usb_hcd_pci_remove(primary)
xhci_irq() // Access the event_queue if STS_EINT is set. Crash.
xhci_stop()
xhci_halt()
// return early
The fix modifies xhci_stop to only cleanup the xhci data when releasing
the primary HCD. This way, we still have the event_queue configured
when invoking xhci_irq. We still halt the device on the first call to
xhci_stop, though.
I could reproduce this issue several times on the mainline kernel by
doing a bind-unbind stress test with a specific storage gadget attached.
I also ran the same test over-night with my patch applied and didn't
observe the issue anymore.
[ 113.334124] Unable to handle kernel paging request for data at address 0x00000028
[ 113.335514] Faulting instruction address: 0xd00000000d4f767c
[ 113.336839] Oops: Kernel access of bad area, sig: 11 [#1]
[ 113.338214] SMP NR_CPUS=1024 NUMA PowerNV
[c000000efe47ba90] c000000000720850 usb_hcd_irq+0x50/0x80
[c000000efe47bac0] c00000000073d328 usb_hcd_pci_remove+0x68/0x1f0
[c000000efe47bb00] d00000000daf0128 xhci_pci_remove+0x78/0xb0
[xhci_pci]
[c000000efe47bb30] c00000000055cf70 pci_device_remove+0x70/0x110
[c000000efe47bb70] c00000000061c6bc __device_release_driver+0xbc/0x190
[c000000efe47bba0] c00000000061c7d0 device_release_driver+0x40/0x70
[c000000efe47bbd0] c000000000619510 unbind_store+0x120/0x150
[c000000efe47bc20] c0000000006183c4 drv_attr_store+0x64/0xa0
[c000000efe47bc60] c00000000039f1d0 sysfs_kf_write+0x80/0xb0
[c000000efe47bca0] c00000000039e14c kernfs_fop_write+0x18c/0x1f0
[c000000efe47bcf0] c0000000002e962c __vfs_write+0x6c/0x190
[c000000efe47bd90] c0000000002eab40 vfs_write+0xc0/0x200
[c000000efe47bde0] c0000000002ec85c SyS_write+0x6c/0x110
[c000000efe47be30] c000000000009260 system_call+0x38/0x108
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: joel@jms.id.au
Cc: stable@vger.kernel.org
Reviewed-by: Roger Quadros <rogerq@ti.com>
Cc: <stable@vger.kernel.org> #v4.3+
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move duplicate code from xhci_queue_intr_tx()
and xhci_queue_isoc_tx_prepare() to the check_interval() function.
Signed-off-by: Alexandr Ivanov <alexandr.sky@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove duplicate function xhci_urb_to_transfer_ring from xhci.c.
We have same function in xhci-ring.c.
Signed-off-by: Alexandr Ivanov <alexandr.sky@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In drivers/usb/host/xhci-ring.c there are two functions
(xhci_queue_bulk_tx and queue_bulk_sg_tx) that are very similar,
so a lot of code duplication.
This patch merges these functions into to one xhci_queue_bulk_tx.
Also counting the needed TRBs is merged and refactored.
Signed-off-by: Alexandr Ivanov <alexandr.sky@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 0.95 xHCI spec says that non-control endpoints will be halted if a
babble is detected on a transfer. The 0.96 xHCI spec says all types of
endpoints will be halted when a babble is detected. Some hardware that
claims to be 0.95 compliant halts the control endpoint anyway.
Reference: http://www.spinics.net/lists/linux-usb/msg21755.html
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PCI hotpluggable xhci controllers such as some Alpine Ridge solutions will
remove the xhci controller from the PCI bus when the last USB device is
disconnected.
Add a flag to indicate that the host is being removed to avoid queueing
configure_endpoint commands for the dropped endpoints.
For PCI hotplugged controllers this will prevent 5 second command timeouts
For static xhci controllers the configure_endpoint command is not needed
in the removal case as everything will be returned, freed, and the
controller is reset.
For now the flag is only set for PCI connected host controllers.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The transfer burst count (TBC) field in the Isoc TRB does not fit the new
larger burst count available for USB 3.1 SSP Isoc tranfers.
xhci 1.1 solved this by reusing the TD size field for transfer burst count.
The Mult field was outgrown as well. xhci 1.1 controllers can calculate
Mult itself and is not set if the new layout is used.
xhci 1.1 controllers that support the new Isoc TRB format expose a
Extended TBC Capability (ETC). To take the new format into use the xhci
host controller driver needs to set a Extended TBC Enable (ETE) bit.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up xhci_queue_isoc_tx() and helpers to prepare them for USB 3.1 and
xhci 1.1 isoc TRB changes.
Only functional change is adding xhci version 1.1 to the BEI flag check
toghether with xhci version 1.0. Both versions behave the same.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit e210c422b6 ("xhci: don't finish a TD if we get a
short transfer event mid TD")
Turns out that most host controllers do not follow the xHCI specs and never
send the second event for the last TRB in the TD if there was a short event
mid-TD.
Returning the URB directly after the first short-transfer event is far
better than never returning the URB. (class drivers usually timeout
after 30sec). For the hosts that do send the second event we will go
back to treating it as misplaced event and print an error message for it.
The origial patch was sent to stable kernels and needs to be reverted from
there as well
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In most cases the devices with the speed set to USB_SPEED_SUPER_PLUS
are handled like regular SuperSpeed devices.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to USB 2 specs ports need to signal resume for at least 20ms,
in practice even longer, before moving to U0 state.
Both host and devices can initiate resume.
On device initiated resume, a port status interrupt with the port in resume
state in issued. The interrupt handler tags a resume_done[port]
timestamp with current time + USB_RESUME_TIMEOUT, and kick roothub timer.
Root hub timer requests for port status, finds the port in resume state,
checks if resume_done[port] timestamp passed, and set port to U0 state.
On host initiated resume, current code sets the port to resume state,
sleep 20ms, and finally sets the port to U0 state. This should also
be changed to work in a similar way as the device initiated resume, with
timestamp tagging, but that is not yet tested and will be a separate
fix later.
There are a few issues with this approach
1. A host initiated resume will also generate a resume event. The event
handler will find the port in resume state, believe it's a device
initiated resume, and act accordingly.
2. A port status request might cut the resume signalling short if a
get_port_status request is handled during the host resume signalling.
The port will be found in resume state. The timestamp is not set leading
to time_after_eq(jiffies, timestamp) returning true, as timestamp = 0.
get_port_status will proceed with moving the port to U0.
3. If an error, or anything else happens to the port during device
initiated resume signalling it will leave all the device resume
parameters hanging uncleared, preventing further suspend, returning
-EBUSY, and cause the pm thread to busyloop trying to enter suspend.
Fix this by using the existing resuming_ports bitfield to indicate that
resume signalling timing is taken care of.
Check if the resume_done[port] is set before using it for timestamp
comparison, and also clear out any resume signalling related variables
if port is not in U0 or Resume state
This issue was discovered when a PM thread busylooped, trying to runtime
suspend the xhci USB 2 roothub on a Dell XPS
Cc: stable <stable@vger.kernel.org>
Reported-by: Daniel J Blueman <daniel@quora.org>
Tested-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There some vendor quirks for MTK xhci host controller:
1. It defines some extra SW scheduling parameters for HW
to minimize the scheduling effort for synchronous and
interrupt endpoints. The parameters are put into reseved
DWs of slot context and endpoint context.
2. Its IMODI unit for Interrupter Moderation register is
8 times as much as that defined in xHCI spec.
3. Its TDS in Normal TRB defines a number of packets that
remains to be transferred for a TD after processing all
Max packets in all previous TRBs.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Tested-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function ep_ring_is_processing() checks the dequeue pointer
in endpoint context to know whether an endpoint is busy with
processing TRBs. This is not correct since dequeue pointer
field in an endpoint context is only valid when the endpoint
is in Halted or Stopped states. This buggy code causes audio
noise when playing sound with USB headset connected to host
controllers which support CFC (one of xhci 1.1 features).
This patch should exist in stable kernel since v4.3.
Reported-and-tested-by: YD Tseng <yd_tseng@asmedia.com.tw>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Cc: stable <stable@vger.kernel.org> # v4.3
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a host fails to wake up a isochronous SuperSpeed device from U1/U2
in time for a isoch transfer it will generate a "No ping response error"
Host will then move to the next transfer descriptor.
Handle this case in the same way as missed service errors, tag the
current TD as skipped and handle it on the next transfer event.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the difference is big enough between the bytes asked and received
in a bulk transfer we can get a short transfer event pointing to a TRB in
the middle of the TD. We don't want to handle the TD yet as we will anyway
receive a new event for the last TRB in the TD.
Hold off from finishing the TD and removing it from the list until we
receive an event for the last TRB in the TD
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci versions 1.0 and later report the untransferred data remaining in a
TD a bit differently than older hosts.
We used to have separate functions for these, and needed to check host
version before calling the right function.
Now Mediatek host has an additional quirk on how it uses the TD Size
field for remaining data. To prevent yet another function for calculating
remainder we instead want to make one quirk friendly unified function.
Tested-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the controller speed to HCD_USB31 to if host hardware supports USB 3.1
For PCI xhci controllers the USB 3.1 support is checked from SBRN bits in
pci config space. Platform controllers will need to set xhci->sbrn == 0x31
to indicate USB 3.1 support before calling xhci_gen_setup().
Also make sure xhci driver works correctly with speed set to HCD_USB31
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB 3.1 capable xhci controllers use a new default speed ID "5" in the
PORTSC register to represent a 10Gbps connection speed of a SuperSpeedPlus
device
Make sure the xhci driver can handle the returned SuperSpeedPlus speed ID
properly
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some changes between xhci 0.96 and xhci 1.0 specifications forced us to
check the hci version in code, some of these checks were implemented as
hci_version == 1.0, which will not work with new xhci 1.1 controllers.
xhci 1.1 behaves similar to xhci 1.0 in these cases, so change these
checks to hci_version >= 1.0
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want to give the command abortion an additional try to stop
the command ring before we completely hose xhci.
Cc: <stable@vger.kernel.org>
Tested-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch enables xhci driver to support SPC by handling
Stopped - Short Packet event in transfer event path.
If SPC = '1' and the stop endpoint command is executed, after a Short
Packet condition has been detected, but before the end of the TD has been
reached, (i.e. the TD is in progress for pipe), then a Transfer Event TRB
with its Completion Code set to Stopped - Short Packet and its TRB
Transfer Length set to value of the EDTLA shall be forced for the
interrupted TRB, irrespective of whether its IOC or ISP flags are set.
This Transfer Event TRB will precede the Command Completion Event TRB for
the command, and is referred to as a Stopped Transfer Event.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the Contiguous Frame ID Capability is supported (CFC = 1),
then the xHC shall match the Frame ID in every Isoch TD with
SIA = 0 against the Frame Index of the MFINDEX register. This
rule ensures resynchronization of Isoch TDs even if some are
dropped due to Missed Service Errors or Stopping the endpoint.
This patch enables xHCI driver to support CFC by calculating
and setting the Frame ID field of an Isoch TRB.
[made some dbg messages checkpatch friendly -Mathias]
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit checks for the URB_ZERO_PACKET flag and creates an extra
zero-length td if the urb transfer length is a multiple of the endpoint's
max packet length.
Signed-off-by: Reyad Attiyat <reyad.attiyat@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to check that a TRB is part of the current segment
before calculating its DMA address.
Previously a ring segment didn't use a full memory page, and every
new ring segment got a new memory page, so the off by one
error in checking the upper bound was never seen.
Now that we use a full memory page, 256 TRBs (4096 bytes), the off by one
didn't catch the case when a TRB was the first element of the next segment.
This is triggered if the virtual memory pages for a ring segment are
next to each in increasing order where the ring buffer wraps around and
causes errors like:
[ 106.398223] xhci_hcd 0000:00:14.0: ERROR Transfer event TRB DMA ptr not part of current TD ep_index 0 comp_code 1
[ 106.398230] xhci_hcd 0000:00:14.0: Looking for event-dma fffd3000 trb-start fffd4fd0 trb-end fffd5000 seg-start fffd4000 seg-end fffd4ff0
The trb-end address is one outside the end-seg address.
Cc: <stable@vger.kernel.org>
Tested-by: Arkadiusz Miśkiewicz <arekm@maven.pl>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the link is just waken, it's in Resume state, and driver sets PLS to
U0. This refers to Phase 1. Phase 2 refers to when the link has completed
the transition from Resume state to U0.
With the fix of xhci: report U3 when link is in resume state, it also
exposes an issue that usb3 roothub and controller can suspend right
after phase 1, and this causes a hard hang in controller.
To fix the issue, we need to prevent usb3 bus suspend if any port is
resuming in phase 1.
[merge separate USB2 and USB3 port resume checking to one -Mathias]
Cc: <stable@vger.kernel.org>
Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the xhci driver from bluntly setting the transferred length to 0 if
we get a STALL on anything else than the data stage of a control transfer.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The problem seems to be that if a new device is detected
while we have already removed the shared HCD, then many of the
xhci operations (e.g. xhci_alloc_dev(), xhci_setup_device())
hang as command never completes.
I don't think XHCI can operate without the shared HCD as we've
already called xhci_halt() in xhci_only_stop_hcd() when shared HCD
goes away. We need to prevent new commands from being queued
not only when HCD is dying but also when HCD is halted.
The following lockup was detected while testing the otg state
machine.
[ 178.199951] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 178.205799] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 178.214458] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x00010010
[ 178.223619] xhci-hcd xhci-hcd.0.auto: irq 400, io mem 0x48890000
[ 178.230677] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 178.237796] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 178.245358] usb usb1: Product: xHCI Host Controller
[ 178.250483] usb usb1: Manufacturer: Linux 4.0.0-rc1-00024-g6111320 xhci-hcd
[ 178.257783] usb usb1: SerialNumber: xhci-hcd.0.auto
[ 178.267014] hub 1-0:1.0: USB hub found
[ 178.272108] hub 1-0:1.0: 1 port detected
[ 178.278371] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 178.284171] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 178.294038] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 178.301183] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 178.308776] usb usb2: Product: xHCI Host Controller
[ 178.313902] usb usb2: Manufacturer: Linux 4.0.0-rc1-00024-g6111320 xhci-hcd
[ 178.321222] usb usb2: SerialNumber: xhci-hcd.0.auto
[ 178.329061] hub 2-0:1.0: USB hub found
[ 178.333126] hub 2-0:1.0: 1 port detected
[ 178.567585] dwc3 48890000.usb: usb_otg_start_host 0
[ 178.572707] xhci-hcd xhci-hcd.0.auto: remove, state 4
[ 178.578064] usb usb2: USB disconnect, device number 1
[ 178.586565] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 178.592585] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 178.597924] usb usb1: USB disconnect, device number 1
[ 178.603248] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 190.597337] INFO: task kworker/u4:0:6 blocked for more than 10 seconds.
[ 190.604273] Not tainted 4.0.0-rc1-00024-g6111320 #1058
[ 190.610228] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 190.618443] kworker/u4:0 D c05c0ac0 0 6 2 0x00000000
[ 190.625120] Workqueue: usb_otg usb_otg_work
[ 190.629533] [<c05c0ac0>] (__schedule) from [<c05c10ac>] (schedule+0x34/0x98)
[ 190.636915] [<c05c10ac>] (schedule) from [<c05c1318>] (schedule_preempt_disabled+0xc/0x10)
[ 190.645591] [<c05c1318>] (schedule_preempt_disabled) from [<c05c23d0>] (mutex_lock_nested+0x1ac/0x3fc)
[ 190.655353] [<c05c23d0>] (mutex_lock_nested) from [<c046cf8c>] (usb_disconnect+0x3c/0x208)
[ 190.664043] [<c046cf8c>] (usb_disconnect) from [<c0470cf0>] (_usb_remove_hcd+0x98/0x1d8)
[ 190.672535] [<c0470cf0>] (_usb_remove_hcd) from [<c0485da8>] (usb_otg_start_host+0x50/0xf4)
[ 190.681299] [<c0485da8>] (usb_otg_start_host) from [<c04849a4>] (otg_set_protocol+0x5c/0xd0)
[ 190.690153] [<c04849a4>] (otg_set_protocol) from [<c0484b88>] (otg_set_state+0x170/0xbfc)
[ 190.698735] [<c0484b88>] (otg_set_state) from [<c0485740>] (otg_statemachine+0x12c/0x470)
[ 190.707326] [<c0485740>] (otg_statemachine) from [<c0053c84>] (process_one_work+0x1b4/0x4a0)
[ 190.716162] [<c0053c84>] (process_one_work) from [<c00540f8>] (worker_thread+0x154/0x44c)
[ 190.724742] [<c00540f8>] (worker_thread) from [<c0058f88>] (kthread+0xd4/0xf0)
[ 190.732328] [<c0058f88>] (kthread) from [<c000e810>] (ret_from_fork+0x14/0x24)
[ 190.739898] 5 locks held by kworker/u4:0/6:
[ 190.744274] #0: ("%s""usb_otg"){.+.+.+}, at: [<c0053bf4>] process_one_work+0x124/0x4a0
[ 190.752799] #1: ((&otgd->work)){+.+.+.}, at: [<c0053bf4>] process_one_work+0x124/0x4a0
[ 190.761326] #2: (&otgd->fsm.lock){+.+.+.}, at: [<c048562c>] otg_statemachine+0x18/0x470
[ 190.769934] #3: (usb_bus_list_lock){+.+.+.}, at: [<c0470ce8>] _usb_remove_hcd+0x90/0x1d8
[ 190.778635] #4: (&dev->mutex){......}, at: [<c046cf8c>] usb_disconnect+0x3c/0x208
[ 190.786700] INFO: task kworker/1:0:14 blocked for more than 10 seconds.
[ 190.793633] Not tainted 4.0.0-rc1-00024-g6111320 #1058
[ 190.799567] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 190.807783] kworker/1:0 D c05c0ac0 0 14 2 0x00000000
[ 190.814457] Workqueue: usb_hub_wq hub_event
[ 190.818866] [<c05c0ac0>] (__schedule) from [<c05c10ac>] (schedule+0x34/0x98)
[ 190.826252] [<c05c10ac>] (schedule) from [<c05c4e40>] (schedule_timeout+0x13c/0x1ec)
[ 190.834377] [<c05c4e40>] (schedule_timeout) from [<c05c19f0>] (wait_for_common+0xbc/0x150)
[ 190.843062] [<c05c19f0>] (wait_for_common) from [<bf068a3c>] (xhci_setup_device+0x164/0x5cc [xhci_hcd])
[ 190.852986] [<bf068a3c>] (xhci_setup_device [xhci_hcd]) from [<c046b7f4>] (hub_port_init+0x3f4/0xb10)
[ 190.862667] [<c046b7f4>] (hub_port_init) from [<c046eb64>] (hub_event+0x704/0x1018)
[ 190.870704] [<c046eb64>] (hub_event) from [<c0053c84>] (process_one_work+0x1b4/0x4a0)
[ 190.878919] [<c0053c84>] (process_one_work) from [<c00540f8>] (worker_thread+0x154/0x44c)
[ 190.887503] [<c00540f8>] (worker_thread) from [<c0058f88>] (kthread+0xd4/0xf0)
[ 190.895076] [<c0058f88>] (kthread) from [<c000e810>] (ret_from_fork+0x14/0x24)
[ 190.902650] 5 locks held by kworker/1:0/14:
[ 190.907023] #0: ("usb_hub_wq"){.+.+.+}, at: [<c0053bf4>] process_one_work+0x124/0x4a0
[ 190.915454] #1: ((&hub->events)){+.+.+.}, at: [<c0053bf4>] process_one_work+0x124/0x4a0
[ 190.924070] #2: (&dev->mutex){......}, at: [<c046e490>] hub_event+0x30/0x1018
[ 190.931768] #3: (&port_dev->status_lock){+.+.+.}, at: [<c046eb50>] hub_event+0x6f0/0x1018
[ 190.940558] #4: (&bus->usb_address0_mutex){+.+.+.}, at: [<c046b458>] hub_port_init+0x58/0xb10
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the xHCI host controller has died (ie, device removed) or suffered
other serious fatal error (STS_FATAL), then xhci_irq should handle this
condition with IRQ_HANDLED instead of -ESHUTDOWN.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Isoc TDs usually consist of one TRB, sometimes two. When all goes well we
receive only one success event for a TD, and move the dequeue pointer to
the next TD.
This fails if the TD consists of two TRBs and we get a transfer error
on the first TRB, we will then see two events for that TD.
Fix this by making sure the event we get is for the last TRB in that TD
before moving the dequeue pointer to the next TD. This will resolve some
of the uvc and dvb issues with the
"ERROR Transfer event TRB DMA ptr not part of current TD" error message
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This part 2 pull request contains only the patches
which make sure everybody on linux uses the same
resume timeout value.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=RqsO
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-testing
Felipe writes:
usb: generic resume timeout for v4.1
This part 2 pull request contains only the patches
which make sure everybody on linux uses the same
resume timeout value.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some toggling operation in xHCI driver still use conditional toggling:
ring->cycle_state = (ring->cycle_state ? 0 : 1);
Use XOR to invert the cycle state instead of a conditional toggle to unify
cycle state toggling operation in xHCI driver.
Signed-off-by: Lin Wang <lin.x.wang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 27082e2654 ("xhci: Clear the host side toggle manually")
Turns out this fix to enable soft resetting endpoints wasn't mature enough.
It caused regression with some usb DVB-T devices and needs some more tuning
to get the endpiont ring pointers set correctly.
The original commit was tagged for stable 3.18, and should be reverted
from there as well.
Cc: stable <stable@vger.kernel.org> # v3.18
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a control transfer has a short data stage, the xHCI controller generates
two transfer events: a COMP_SHORT_TX event that specifies the untransferred
amount, and a COMP_SUCCESS event. But when the data stage is not short, only the
COMP_SUCCESS event occurs. Therefore, xhci-hcd must set urb->actual_length to
urb->transfer_buffer_length while processing the COMP_SUCCESS event, unless
urb->actual_length was set already by a previous COMP_SHORT_TX event.
The driver checks this by seeing whether urb->actual_length == 0, but this alone
is the wrong test, as it is entirely possible for a short transfer to have an
urb->actual_length = 0.
This patch changes the xhci driver to rely on a new td->urb_length_set flag,
which is set to true when a COMP_SHORT_TX event is received and the URB length
updated at that stage.
This fixes a bug which affected the HSO plugin, which relies on URBs with
urb->actual_length == 0 to halt re-submitting the RX URB in the control
endpoint.
Cc: <stable@vger.kernel.org>
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Main benefit of this is to get xhci connected USB scanners to work.
Some devices use a clear endpoint halt request as a 'soft reset' even if
the endpoint is not halted. This will clear the toggle and sequence on the
device side. xHCI however refuses to reset a non-halted endpoint, so instead
we need to issue a configure endpoint command on xHCI to clear its host side
toggle and sequence, and get it in sync with the device side.
Tested-by: Mike Mammarella <mikem@crystalorb.net>
Cc: <stable@vger.kernel.org> # v3.18
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Helps debugging to know the unhandled event type.
Also make the debug message grepable
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some parameters are not used by functions in xhci-mem.c, just
remove it.
Changes compared to v1:
- Rebase to the latest usb-next branch
Signed-off-by: Lin Wang <lin.x.wang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Parameter 'xhci' is no longer be used in function xhci_handshake(),
just remove it.
Signed-off-by: Lin Wang <lin.x.wang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Endpoints halted on errors, and endpoints stopped manually both used
the same ep->stopped_td to store the halted or stopped td. this causes
confusion and possible races.
There is no longer a need to use the ep->stopped_td variable to store
the halted TD. A halted endpoint is handled immediately and we can pass
it to the handling function directly.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a device is halted and reuturns a STALL, then the halted endpoint
needs to be cleared both on the host and device side. The host
side halt is cleared by issueing a xhci reset endpoint command. The device side
is cleared with a ClearFeature(ENDPOINT_HALT) request, which should
be issued by the device driver if a URB reruen -EPIPE.
Previously we cleared the host side halt after the device side was cleared.
To make sure the host side halt is cleared in time we want to issue the
reset endpoint command immedialtely when a STALL status is encountered.
Otherwise we end up not following the specs and not returning -EPIPE
several times in a row when trying to transfer data to a halted endpoint.
Fixes: bcef3fd (USB: xhci: Handle errors that cause endpoint halts.)
Cc: <stable@vger.kernel.org> # v2.6.33+
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A halted endpoint ring must first be reset, then move the ring
dequeue pointer past the problematic TRB. If we start the ring too
early after reset, but before moving the dequeue pointer we
will end up executing the same problematic TRB again.
As we always issue a set transfer dequeue command after a reset
endpoint command we can skip starting endpoint rings at reset endpoint
command completion.
Without this fix we end up trying to handle the same faulty TD for
contol endpoints. causing timeout, and failing testusb ctrl_out write
tests.
Fixes: e9df17e (USB: xhci: Correct assumptions about number of rings per endpoint.)
Cc: <stable@vger.kernel.org> #v2.6.35
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lately (with the use of uas / bulk-streams) we have been seeing several
cases where this error triggers (which should never happen).
Add some extra logging to make debugging these errors easier.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even though a Set TR deq ptr command operates on a ring, and an endpoint
can have multiple rings, we can have only one Set TR deq ptr command pending.
When an endpoint with streams halts or is stopped to unlink urbs, there
will only be at most one ring active / one td being executed (the td
stopped_td points to).
So when we reset the endpoint (for a halt), or the stop command completes, we
will queue one Set TR deq ptr command at most, cancelled urbs on other stream
rings then the one being executed will have there trbs turned to nops, and
once the hcd gets around to execute that stream ring they will be simply
skipped.
So the SET_DEQ_PENDING flag in the endpoint is sufficient protection against
starting the endpoing before all stream rings are cleaned up.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even if the stream for which the command was intended has been freed in the
mean time. This ensures that things start rolling again after an unlink / halt.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_queue_new_dequeue_state is the only caller of queue_set_tr_deq
and queue_set_tr_deq checks for SET_DEQ_PENDING, where as
xhci_queue_new_dequeue_state sets it which is inconsistent.
Simply fold the 2 into one is a nice cleanup and fixes the inconsistency.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are multiple reasons for this:
1) This fixes a missing check for xhci_alloc_command failing in
xhci_handle_cmd_stop_ep()
2) This adds a warning when we cannot set the new dequeue state because of
xhci_alloc_command failing
3) It puts the allocation of the command after the sanity checks in
queue_set_tr_deq(), avoiding leaking the command if those fail
4) Since queue_set_tr_deq now owns the command it can free it if queue_command
fails
5) It reduces code duplication
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we manually need to move the TR dequeue pointer we need to set the
correct cycle bit as well. Previously we used the trb pointer from the
last event received as a base, but this was changed in
commit 1f81b6d22a ("usb: xhci: Prefer endpoint context dequeue pointer")
to use the dequeue pointer from the endpoint context instead
It turns out some Asmedia controllers advance the dequeue pointer
stored in the endpoint context past the event triggering TRB, and
this messed up the way the cycle bit was calculated.
Instead of adding a quirk or complicating the already hard to follow cycle bit
code, the whole cycle bit calculation is now simplified and adapted to handle
event and endpoint context dequeue pointer differences.
Fixes: 1f81b6d22a ("usb: xhci: Prefer endpoint context dequeue pointer")
Reported-by: Maciej Puzio <mx34567@gmail.com>
Reported-by: Evan Langlois <uudruid74@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: Maciej Puzio <mx34567@gmail.com>
Tested-by: Evan Langlois <uudruid74@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using a Renesas uPD720231 chipset usb-3 uas to sata bridge with a 120G
Crucial M500 ssd, model string: Crucial_ CT120M500SSD1, together with a
the integrated Intel xhci controller on a Haswell laptop:
00:14.0 USB controller [0c03]: Intel Corporation 8 Series USB xHCI HC [8086:9c31] (rev 04)
The following error gets logged to dmesg:
xhci error: Transfer event TRB DMA ptr not part of current TD
Treating COMP_STOP the same as COMP_STOP_INVAL when no event_seg gets found
fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The transfer burst count (TBC) field in xhci 1.0 hosts should be set
to the number of bursts needed to transfer all packets in a isoc TD.
Supported values are 0-2 (1 to 3 bursts per service interval).
Formula for TBC calculation is given in xhci spec section 4.11.2.3:
TBC = roundup( Transfer Descriptor Packet Count / Max Burst Size +1 ) - 1
This patch should be applied to stable kernels since 3.0 that contain
the commit 5cd43e33b9
"xhci 1.0: Set transfer burst count field."
Cc: stable@vger.kernel.org # 3.0
Suggested-by: ShiChun Ma <masc2008@qq.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Command completion events normally include command completion status,
SLOT_ID, and a pointer to the original command. Reset device command
completion SLOT_ID may be zero according to xhci specs 4.6.11.
VIA controllers set the SLOT_ID to zero, triggering a WARN_ON in the
command completion handler.
Use the SLOT ID found from the original command instead.
This patch should be applied to stable kernels since 3.13 that contain
the commit 20e7acb13f
"xhci: use completion event's slot id rather than dig it out of command"
Cc: stable@vger.kernel.org # 3.13
Reported-by: Saran Neti <sarannmr@gmail.com>
Tested-by: Saran Neti <sarannmr@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use one timer to control command timeout.
start/kick the timer every time a command is completed and a
new command is waiting, or a new command is added to a empty list.
If the timer runs out, then tag the current command as "aborted", and
start the xhci command abortion process.
Previously each function that submitted a command had its own timer.
If that command timed out, a new command structure for the
command was created and it was put on a cancel_cmd_list list,
then a pci write to abort the command ring was issued.
when the ring was aborted, it checked if the current command
was the one to be canceled, later when the ring was stopped the
driver got ownership of the TRBs in the command ring,
compared then to the TRBs in the cancel_cmd_list,
and turned them into No-ops.
Now, instead, at timeout we tag the status of the command in the
command queue to be aborted, and start the ring abortion.
Ring abortion stops the command ring and gives control of the
commands to us.
All the aborted commands are now turned into No-ops.
If the ring is already stopped when the command times outs its not possible
to start the ring abortion, in this case the command is turnd to No-op
right away.
All these changes allows us to remove the entire cancel_cmd_list code.
The functions waiting for a command to finish no longer have their own timeouts.
They will wait either until the command completes normally,
or until the whole command abortion is done.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the per-device command list and handle_cmd_in_cmd_wait_list()
and use the completion and status variables found in the
command structure in the global command list.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Create a list to store command structures, add a structure to it every time
a command is submitted, and remove it from the list once we get a
command completion event matching the command.
Callers that wait for completion will free their command structures themselves.
The other command structures are freed in the command completion event handler.
Also add a check that prevents queuing commands if host is dying
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To create a global command queue we require that each command put on the
command ring is submitted with a command structure.
Functions that queue commands and wait for completion need to allocate a command
before submitting it, and free it once completed. The following command queuing
functions need to be modified.
xhci_configure_endpoint()
xhci_address_device()
xhci_queue_slot_control()
xhci_queue_stop_endpoint()
xhci_queue_new_dequeue_state()
xhci_queue_reset_ep()
xhci_configure_endpoint()
xhci_configure_endpoint() could already be called with a command structure,
and only xhci_check_maxpacket and xhci_check_bandwidth did not do so. These
are changed and a command structure is now required. This change also simplifies
the configure endpoint command completion handling and the "goto bandwidth_change"
handling code can be removed.
In some cases the command queuing function is called in interrupt context.
These commands needs to be allocated atomically, and they can't wait for
completion. These commands will in this patch be freed directly after queuing,
but freeing will be moved to the command completion event handler in a later
patch once we get the global command queue up.(Just so that we won't leak
memory in the middle of the patch set)
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have observed a rare cycle state desync bug after Set TR Dequeue
Pointer commands on Intel LynxPoint xHCs (resulting in an endpoint that
doesn't fetch new TRBs and thus an unresponsive USB device). It always
triggers when a previous Set TR Dequeue Pointer command has set the
pointer to the final Link TRB of a segment, and then another URB gets
enqueued and cancelled again before it can be completed. Further
investigation showed that the xHC had returned the Link TRB in the TRB
Pointer field of the Transfer Event (CC == Stopped -- Length Invalid),
but when xhci_find_new_dequeue_state() later accesses the Endpoint
Context's TR Dequeue Pointer field it is set to the first TRB of the
next segment.
The driver expects those two values to be the same in this situation,
and uses the cycle state of the latter together with the address of the
former. This should be fine according to the XHCI specification, since
the endpoint ring should be stopped when returning the Transfer Event
and thus should not advance over the Link TRB before it gets restarted.
However, real-world XHCI implementations apparently don't really care
that much about these details, so the driver should follow a more
defensive approach to try to work around HC spec violations.
This patch removes the stopped_trb variable that had been used to store
the TRB Pointer from the last Transfer Event of a stopped TRB. Instead,
xhci_find_new_dequeue_state() now relies only on the Endpoint Context,
requiring a small amount of additional processing to find the virtual
address corresponding to the TR Dequeue Pointer. Some other parts of the
function were slightly rearranged to better fit into this model.
This patch should be backported to kernels as old as 2.6.31 that contain
the commit ae63674714 "USB: xhci: URB
cancellation support."
Signed-off-by: Julius Werner <jwerner@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the host controller stops responding to commands, we need to kill all
the URBs that were queued to all endpoints. The current code would only
kill URBs that had been queued to the endpoint rings. ep->ring is set
to NULL if streams has been enabled for the endpoint, which means URBs
submitted with a non-zero stream_id would never get killed. Fix this.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
In preparation for fixing this function for streams endpoints, refactor
code in the command watchdog timeout function into two new functions.
One kills all URBs on a ring (either stream or endpoint), the other
kills all URBs associated with an endpoint. Fix a split string while
we're at it.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This fixes TR dequeue validation failing on Intel XHCI controllers with the
following warning:
Mismatch between completed Set TR Deq Ptr command & xHCI internal state.
Interestingly enough reading the deq ptr from the ep ctx after a
TR Deq Ptr command does work on a Nec XHCI controller, it seems the Nec
writes the ptr to both the ep and stream contexts when streams are used.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Nec XHCI controllers don't seem to care, but without this Intel XHCI
controllers reject Set TR dequeue commands with a COMP_TRB_ERR, leading
to the following warning:
WARN Set TR Deq Ptr cmd invalid because of stream ID configuration
And very shortly after this the system completely freezes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This changes debug messages and warnings in xhci-ring.c
to be on a single line so grep can find them. grep must
have precedence over the 80 column limit.
[Sarah fixed two checkpatch.pl issues with split lines
introduced by this commit.]
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This reverts commit 35773dac5f. It's a
hack that caused regressions in the usb-storage and userspace USB
drivers that use usbfs and libusb. Commit 70cabb7d992f "xhci 1.0: Limit
arbitrarily-aligned scatter gather." should fix the issues seen with the
ax88179_178a driver on xHCI 1.0 hosts, without causing regressions.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org # 3.12
This reverts commit d6c9ea9069.
We are ripping out commit 35773dac5f "usb:
xhci: Link TRB must not occur within a USB payload burst" because it's a
hack that caused regressions in the usb-storage and userspace USB
drivers that use usbfs and libusb. This commit attempted to fix the
issues with that patch.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org # 3.12
This reverts commit e8b373326d. Many xHCI
host controllers can only handle 32-bit addresses, and writing 64-bits
at a time causes them to fail. Reading 64-bits at a time may also cause
them to return 0xffffffff, so revert this commit as well.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This reverts commit 7dd09a1af2.
Many xHCI host controllers can only handle 32-bit addresses, and writing
64-bits at a time causes them to fail. Rafał reports that USB devices
simply do not enumerate, and reverting this patch helps. Branimir
reports that his host controller doesn't respond to an Enable Slot
command and dies:
[ 75.576160] xhci_hcd 0000:03:00.0: Timeout while waiting for a slot
[ 88.991634] xhci_hcd 0000:03:00.0: Stopped the command ring failed, maybe the host is dead
[ 88.991748] xhci_hcd 0000:03:00.0: Abort command ring failed
[ 88.991845] xhci_hcd 0000:03:00.0: HC died; cleaning up
[ 93.985489] xhci_hcd 0000:03:00.0: Timeout while waiting for a slot
[ 93.985494] xhci_hcd 0000:03:00.0: Abort the command ring, but the xHCI is dead.
[ 98.982586] xhci_hcd 0000:03:00.0: Timeout while waiting for a slot
[ 98.982591] xhci_hcd 0000:03:00.0: Abort the command ring, but the xHCI is dead.
[ 103.979696] xhci_hcd 0000:03:00.0: Timeout while waiting for a slot
[ 103.979702] xhci_hcd 0000:03:00.0: Abort the command ring, but the xHCI is dead
Signed-off-by: Sarah Sharp <sarah.a.sharp@intel.com>
Reported-by: Rafał Miłecki <zajec5@gmail.com>
Reported-by: Branimir Maksimovic <branimir.maksimovic@gmail.com>
Cc: Xenia Ragiadakou <burzalodowa@gmail.com>
Currently prepare_ring() returns -ENOMEM if the urb won't fit into a
single ring segment. usb_sg_wait() treats this error as a temporary
condition and will keep retrying until something else goes wrong.
The number of retries should be limited in usb_sg_wait(), but also
prepare_ring() should not return an error code that suggests it might
be worth retrying. Change it to -EINVAL.
Reported-by: jidanni@jidanni.org
References: http://bugs.debian.org/733907
Fixes: 35773dac5f ('usb: xhci: Link TRB must not occur within a USB payload burst')
Cc: stable <stable@vger.kernel.org> # 3.12
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Happy Holidays, Greg!
Here's four patches to be queued to usb-next for 3.14.
One adds a module parameter to the xHCI driver to allow users to enable
xHCI quirks without recompiling their kernel, which you've already said
is fine. The second patch is a bug fix for new usbtest code that's only
in usb-next. The third patch is simple cleanup.
The last patch is a non-urgent bug fix for xHCI platform devices. The
bug has been in the code since 3.9. You've been asking me to hold off
on non-urgent bug fixes after -rc4/-rc5, so it can go into usb-next, and
be backported to stable once 3.14 is out.
These have all been tested over the past week. I did run across one
oops, but it turned out to be a bug in 3.12, and therefore not related
to any of these patches.
Please queue these for usb-next and 3.14.
Thanks,
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=PRbx
-----END PGP SIGNATURE-----
Merge tag 'for-usb-next-2013-12-20' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-next
Sarah writes:
xhci: Cleanups, non-urgent fixes for 3.14.
Happy Holidays, Greg!
Here's four patches to be queued to usb-next for 3.14.
One adds a module parameter to the xHCI driver to allow users to enable
xHCI quirks without recompiling their kernel, which you've already said
is fine. The second patch is a bug fix for new usbtest code that's only
in usb-next. The third patch is simple cleanup.
The last patch is a non-urgent bug fix for xHCI platform devices. The
bug has been in the code since 3.9. You've been asking me to hold off
on non-urgent bug fixes after -rc4/-rc5, so it can go into usb-next, and
be backported to stable once 3.14 is out.
These have all been tested over the past week. I did run across one
oops, but it turned out to be a bug in 3.12, and therefore not related
to any of these patches.
Please queue these for usb-next and 3.14.
Thanks,
Sarah Sharp
This patch remove unused variable 'addr' in inc_deq() and inc_enq().
Signed-off-by: Lin Wang <lin.x.wang@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Change the default enumeration scheme for xhci attached non-SuperSpeed
devices from:
Reset
SetAddress [xhci address-device BSR = 0]
GetDescriptor(8)
GetDescriptor(18)
...to:
Reset
[xhci address-device BSR = 1]
GetDescriptor(64)
Reset
SetAddress [xhci address-device BSR = 0]
GetDescriptor(18)
...as some devices misbehave when encountering a SetAddress command
prior to GetDescriptor. There are known legacy devices that require
this scheme, but testing has found at least one USB3 device that fails
enumeration when presented with this ordering. For now, follow the ehci
case and enable 'new scheme' by default for non-SuperSpeed devices.
To support this enumeration scheme on xhci the AddressDevice operation
needs to be performed twice. The first instance of the command enables
the HC's device and slot context info for the device, but omits sending
the device a SetAddress command (BSR == block set address request).
Then, after GetDescriptor completes, follow up with the full
AddressDevice+SetAddress operation.
As mentioned before, this ordering of events with USB3 devices causes an
extra state transition to be exposed to xhci. Previously USB3 devices
would transition directly from 'enabled' to 'addressed' and never need
to underrun responses to 'get descriptor'. We do see the 64-byte
descriptor fetch the correct data, but the following 18-byte descriptor
read after the reset gets:
bLength = 0
bDescriptorType = 0
bcdUSB = 0
bDeviceClass = 0
bDeviceSubClass = 0
bDeviceProtocol = 0
bMaxPacketSize0 = 9
instead of:
bLength = 12
bDescriptorType = 1
bcdUSB = 300
bDeviceClass = 0
bDeviceSubClass = 0
bDeviceProtocol = 0
bMaxPacketSize0 = 9
which results in the discovery process looping until falling back to
'old scheme' enumeration.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: David Moore <david.moore@gmail.com>
Suggested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Function xhci_write_64() is used to write 64bit xHC registers residing in MMIO.
On 32bit systems, xHC registers need to be written with 32bit accesses by
writing first the lower 32bits and then the higher 32bits. The header file
asm-generic/io-64-nonatomic-lo-hi.h ensures that on 32bit systems writeq() will
will write 64bit registers in 32bit chunks with low-high order.
Replace all calls to xhci_write_64() with calls to writeq().
This is done to reduce code duplication since 64bit low-high write logic
is already implemented and to take advantage of inherent "atomic" 64bit
write operations on 64bit systems.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Function xhci_read_64() is used to read 64bit xHC registers residing in MMIO.
On 32bit systems, xHC registers need to be read with 32bit accesses by
reading first the lower 32bits and then the higher 32bits.
Replace all calls to xhci_read_64() with calls to readq() and include
asm-generic/io-64-nonatomic-lo-hi.h header file, so that if the system
is not 64bit, readq() will read registers in 32bit chunks with low-high order.
This is done to reduce code duplication since 64bit low-high read logic
is already implemented and to take advantage of inherent "atomic" 64bit
read operations on 64bit systems.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Function xhci_writel() is used to write a 32bit value in xHC registers residing
in MMIO address space. It takes as first argument a pointer to the xhci_hcd
although it does not use it. xhci_writel() internally simply calls writel().
This creates an illusion that xhci_writel() is an xhci specific function that
has to be called in a context where a pointer to xhci_hcd is available.
Remove xhci_writel() wrapper function and replace its calls with calls to
writel() to make the code more straight-forward.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Function xhci_readl() is used to read 32bit xHC registers residing in MMIO
address space. It takes as first argument a pointer to the xhci_hcd although
it does not use it. xhci_readl() internally simply calls readl(). This creates
an illusion that xhci_readl() is an xhci specific function that has to be
called in a context where a pointer to xhci_hcd is available.
Remove the unnecessary xhci_readl() wrapper function and replace its calls to
with calls to readl() to make the code more straightforward.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch converts Event TRB's 3rd field, which has type le32, to CPU
byteorder before using it to retrieve the Slot ID with TRB_TO_SLOT_ID macro.
This bug was found using sparse.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Section 4.11.7.1 of rev 1.0 of the xhci specification states that a link TRB
can only occur at a boundary between underlying USB frames (512 bytes for
high speed devices).
If this isn't done the USB frames aren't formatted correctly and, for example,
the USB3 ethernet ax88179_178a card will stop sending (while still receiving)
when running a netperf tcp transmit test with (say) and 8k buffer.
This should be a candidate for stable, the ax88179_178a driver defaults to
gso and tso enabled so it passes a lot of fragmented skb to the USB stack.
Notes from Sarah:
Discussion: http://marc.info/?l=linux-usb&m=138384509604981&w=2
This patch fixes a long-standing xHCI driver bug that was revealed by a
change in 3.12 in the usb-net driver. Commit
638c5115a7 "USBNET: support DMA SG" added
support to use bulk endpoint scatter-gather (urb->sg). Only the USB
ethernet drivers trigger this bug, because the mass storage driver sends
sg list entries in page-sized chunks.
This patch only fixes the issue for bulk endpoint scatter-gather. The
problem will still occur for periodic endpoints, because hosts will
interpret no-op transfers as a request to skip a service interval, which
is not what we want.
Luckily, the USB core isn't set up for scatter-gather on isochronous
endpoints, and no USB drivers use scatter-gather for interrupt
endpoints. Document this known limitation so that developers won't try
to use urb->sg for interrupt endpoints until this issue is fixed. The
more comprehensive fix would be to allow link TRBs in the middle of the
endpoint ring and revert this patch, but that fix would touch too much
code to be allowed in for stable.
This patch should be backported to kernels as old as 3.12, that contain
the commit 638c5115a7 "USBNET: support DMA
SG". Without this patch, the USB network device gets wedged, and stops
sending packets. Mark Lord confirms this patch fixes the regression:
http://marc.info/?l=linux-netdev&m=138487107625966&w=2
Signed-off-by: David Laight <david.laight@aculab.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Mark Lord <mlord@pobox.com>
Cc: stable@vger.kernel.org
Perform an unconditional toggle of the cycle bit with 'xor'.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch replaces the 'event' argument of xhci_handle_cmd_set_deq() and
xhci_handle_cmd_reset_ep(), which is used to retrieve the command completion
status code, with the cmd_comp_code directly, since it is available.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Since the Slot ID field in the command completion event matches the Slot ID
field in the associated command TRB for the Stop Endpoint, Set Dequeue Pointer
and Reset Endpoint commands, this patch adds in the handlers of their
completion events a 'slot_id' argument and removes the slot id calculation
in each of them.
Also, a WARN_ON() was added in case the slot ids reported by command TRB and
event TRB differ (although according to xhci spec rev1.0 that should not happen)
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch replaces 'xhci->cmd_ring->dequeue' with 'trb', the address of
the command TRB, since it is available to reduce line length.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch adds a new variable 'cmd_type' to hold the command type so that
switch cases can be simplified by removing TRB_TYPE() macro improving
code readability.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch adds a new variable 'cmd_trb' to hold the address of the
command TRB, that is associated with the command completion event,
and to replace repetitions of xhci->cmd_ring->dequeue into the code.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch adds a new variable 'cmd_comp_code' to hold the command completion
status code aiming to reduce code duplication and to improve code readability.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The function that handles xHCI command completion is much too long and
there is need to be broken up into individual functions for each command
completion to improve code readablity.
This patch refactors the code in TRB_CONFIG_EP switch case, in
handle_cmd_completion(), into a fuction named xhci_handle_cmd_config_ep().
There were added two additional variables, 'add_flags' and 'drop_flags',
to reduce line length below 80 chars and improve code readability.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch removes the variable 'ep_ring' that is assigned in
TRB_CONFIG_EP switch case but never used.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The function that handles xHCI command completion is much too long and
there is need to be broken up into individual functions for each command
completion to improve code readablity.
This patch refactors the code in TRB_EVAL_CONTEXT switch case in
handle_cmd_completion() into a fuction named xhci_handle_cmd_eval_ctx().
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The function that handles xHCI command completion is much too long and
there is need to be broken up into individual functions for each command
completion to improve code readablity.
This patch refactors the code in TRB_NEC_GET_FW switch case in
handle_cmd_completion() into a fuction named xhci_handle_cmd_nec_get_fw().
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The function that handles xHCI command completion is much too long and
there is need to be broken up into individual functions for each command
completion to improve code readablity.
This patch refactors the code in TRB_RESET_DEV switch case in
handle_cmd_completion() into a fuction named xhci_handle_cmd_reset_dev().
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Since the slot id retrieved from the Reset Device TRB matches the slot id in
the command completion event, which is available, there is no need to determine
it again.
This patch removes the uneccessary reassignment to slot id and adds a WARN_ON
in case the two Slot ID fields differ (although according xhci spec rev1.0
they should not differ).
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The function that handles xHCI command completion is much too long and
there is need to be broken up into individual functions for each command
completion to improve code readablity.
This patch refactors the code in TRB_ADDR_DEV switch case in
handle_cmd_completion() into a fuction named xhci_handle_cmd_addr_dev().
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The function that handles xHCI command completion is much too long and
there is need to be broken up into individual functions for each command
completion to improve code readablity.
This patch refactors the code in TRB_DISABLE_SLOT switch case in
handle_cmd_completion() into a fuction named xhci_handle_cmd_disable_slot().
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The function that handles xHCI command completion is much too long and
there is need to be broken up into individual functions for each command
completion to improve code readablity.
This patch refactors the code in TRB_ENABLE_SLOT switch case in
handle_cmd_completion() into a fuction named xhci_handle_cmd_enable_slot().
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch renames the function handlers of a triggered Command Completion
Event that correspond to each command type into 'xhci_handle_cmd_<type>'.
That is done to give a consistent naming space to all the functions that
handle Command Completion Events and that will permit the code reader to
reference to them more easily.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch removes the "adjective" argument from xhci_giveback_urb_in_irq(),
since it is not used in the function anymore.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The halted state of a endpoint cannot be cleared over CLEAR_HALT from a
user process, because the stopped_td variable was overwritten in the
handle_stopped_endpoint() function. So the xhci_endpoint_reset() function will
refuse the reset and communication with device can not run over this endpoint.
https://bugzilla.kernel.org/show_bug.cgi?id=60699
Signed-off-by: Florian Wolter <wolly84@web.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
When a device signals remote wakeup on a roothub, and the suspend change
bit is set, the host controller driver must not give control back to the
USB core until the port goes back into the active state.
EHCI accomplishes this by waiting in the get port status function until
the PORT_RESUME bit is cleared:
/* stop resume signaling */
temp &= ~(PORT_RWC_BITS | PORT_SUSPEND | PORT_RESUME);
ehci_writel(ehci, temp, status_reg);
clear_bit(wIndex, &ehci->resuming_ports);
retval = ehci_handshake(ehci, status_reg,
PORT_RESUME, 0, 2000 /* 2msec */);
Similarly, the xHCI host should wait until the port goes into U0, before
passing control up to the USB core. When the port transitions from the
RExit state to U0, the xHCI driver will get a port status change event.
We need to wait for that event before passing control up to the USB
core.
After the port transitions to the active state, the USB core should time
a recovery interval before it talks to the device. The length of that
recovery interval is TRSMRCY, 10 ms, mentioned in the USB 2.0 spec,
section 7.1.7.7. The previous xHCI code (which did not wait for the
port to go into U0) would cause the USB core to violate that recovery
interval.
This bug caused numerous USB device disconnects on remote wakeup under
ChromeOS and a Lynx Point LP xHCI host that takes up to 20 ms to move
from RExit to U0. ChromeOS is very aggressive about power savings, and
sets the autosuspend_delay to 100 ms, and disables USB persist.
I attempted to replicate this bug with Ubuntu 12.04, but could not. I
used Ubuntu 12.04 on the same platform, with the same BIOS that the bug
was triggered on ChromeOS with. I also changed the USB sysfs settings
as described above, but still could not reproduce the bug under Ubuntu.
It may be that ChromeOS userspace triggers this bug through additional
settings.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
If a command on the command ring needs to be cancelled before it is handled
it can be turned to a no-op operation when the ring is stopped.
We want to store the command ring enqueue pointer in the command structure
when the command in enqueued for the cancellation case.
Some commands used to store the command ring dequeue pointers instead of enqueue
(these often worked because enqueue happends to equal dequeue quite often)
Other commands correctly used the enqueue pointer but did not check if it pointed
to a valid trb or a link trb, this caused for example stop endpoint command to timeout in
xhci_stop_device() in about 2% of suspend/resume cases.
This should also solve some weird behavior happening in command cancellation cases.
This patch is based on a patch submitted by Sarah Sharp to linux-usb, but
then forgotten:
http://marc.info/?l=linux-usb&m=136269803207465&w=2
This patch should be backported to kernels as old as 3.7, that contain
the commit b92cc66c04 "xHCI: add aborting
command ring function"
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
When a command times out, the command ring is first aborted,
and then stopped. If the command ring is empty when it is stopped
the stop event will point to next command which is not yet set.
xHCI tries to handle this next event often causing an oops.
Don't handle command completion events on stopped cmd ring if ring is
empty.
This patch should be backported to kernels as old as 3.7, that contain
the commit b92cc66c04 "xHCI: add aborting
command ring function"
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reported-by: Giovanni <giovanni.nervi@yahoo.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
When debug is not enabled and dev_dbg() will expand to nothing,
log might be flooded with "callbacks suppressed". If it was not
done on purpose, better to use dev_dbg_ratelimited() instead.
Signed-off-by: Dmitry Kasatkin <d.kasatkin@samsung.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch defines a new trace event, which is called xhci_dbg_ring_expansion
and belongs to the event class xhci_log_msg, and adds tracepoints that trace
the debug messages associated with the expansion of endpoint ring when there
is not enough space allocated to hold all pending TRBs.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Mathias Nyman