"drm/ttm: callback move_notify any time bo placement change v4" failed to
avoid a NULL pointer dereference in nouveau caused by move_notify being
expected to handle that case now.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
- moves out of nouveau_bios.c and demagics the logical state definitions
- simplifies chipset-specific driver interface
- makes most of gpio irq handling common, will use for nv4x hpd later
- api extended to allow both direct gpio access, and access using the
logical function states
- api extended to allow for future use of gpio extender chips
- pre-nv50 was handled very badly, the main issue being that all GPIOs
were being treated as output-only.
- fixes nvd0 so gpio changes actually stick, magic reg needs bashing
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We don't need more than the line id to determine the PWM controller, and
the GPIO interfaces are about to change somewhat.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
More work needs to be done on supporting the different memory types.
v2 (Ben Skeggs):
- fixed up conflicts from not having pausing patch first
- restructured code somewhat to fit with how all the other code works
- fixed bug where incorrect mpll_ctrl could get set sometimes
- removed stuff that's cargo-culted from the binary driver
- merged nv92+ display disable into hwsq
- fixed incorrect opcode 0x5f magic at end of ucode
Signed-off-by: Martin Peres <martin.peres@ensi-bourges.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The DCB table provided by the VBIOS on most MXM chips has a number of
entries which either need to be disabled, or modified according to the
MXM-SIS Output Device Descriptors.
The x86 vbios code usually takes care of this for us, however, with the
large number of laptops now with switchable graphics or optimus, a lot
of the time nouveau is responsible for POSTing the card instead - leaving
some fun situations like, plugging in a monitor and having nouveau decide
3 connectors actually just got plugged in..
No MXM-SIS fetching methods implemented yet.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Another case where we parsed vbios data to some structs, then again use
that info once to construct another set of data. Skip the intermediate
step.
This is also slightly improved in that we can now use DCB 3.x connector
table info, which will allow NV4x to gain hotplug support, and to make
quirks for SPWG LVDS panels unnecessary.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
i2c-algo-bit doesn't actually work very well on one card I have access to
(NVS 300), random single-bit errors occur most of the time - what we're
doing now is closer to what xf86i2c.c does.
The original plan was to figure out why i2c-algo-bit fails on the NVS 300,
and fix it. However, while investigating I discovered i2c-algo-bit calls
cond_resched(), which makes it a bad idea for us to be using as we execute
VBIOS scripts from a tasklet, and there may very well be i2c transfers as
a result.
So, since I already wrote this code in userspace to track down the NVS 300
bug, and it's not really much code - lets use it.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Was using nv_mask, which is bad. Reading the reg senses the current line
states, which aren't necessarily the states we're trying to drive the
lines to.
Fixed to store SCL driver state just as we already do for SDA.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Not much point parsing the vbios data into a struct which is only used once
to parse the data into another struct, go directly from vbios to
nouveau_i2c_chan.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This primary reason for this was mostly to avoid duplication of some of
this stuff by the MXM-SIS parser. However, some other cleanups will also
follow this as a result.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Spotted while messing with overlay channels (probably as a result of
sending a similar "disable" sequence as we do for the flip channels).
The value in 0x61008c was 0x20, which one would reasonably guess is
"bit 5 == something to report about evo channel 5" - but who knows.
Spotted the binary driver getting this too, and it appears to not do
anything exciting as a result. So, handle it the same way and avoid
an IRQ storm.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Pre-nva3 will likely require far more extensive setup, and nvd9 needs to
be checked to find its SOR_HDMI/SOR_AUDIO blocks.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs