This patch fixes a bug found by Nish Aravamudan
(https://lkml.org/lkml/2012/5/15/220) where the driver is not following
the spec (it is not aligning the rx buffer on a 16-byte boundary) and the
hypervisor aborts the registration, making the device unusable.
The fix follows BenH's recommendation (https://lkml.org/lkml/2012/7/20/461)
to replace the kmalloc+map for a single call to dma_alloc_coherent()
because that function always aligns to a 16-byte boundary.
The stable trees will run into this bug whenever the rx buffer kmalloc call
returns something not aligned on a 16-byte boundary.
Cc: <stable@vger.kernel.org>
Signed-off-by: Santiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
davinci mdio device is not unregistered from mdiobus when removing
the module, which causes BUG_ON() when free the device from mdiobus.
Calling mdiobus_unregister() before mdiobus_free() fixes the issue.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RxCFG register of the CS89x0 could be configured incorrectly
(because of misplaced parentheses), resulting in the disabling
of packet reception.
Signed-off-by: Jaccon Bastiaansen <jaccon.bastiaansen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch correct poll_bnx2x (ndo_poll_controller call) which was not
functioning well with MSI-X.
Signed-off-by: Merav Sicron <meravs@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move netif_napi_add for all queues from the probe call to the open call, to
avoid the case that napi objects are added for queues that may eventually not
be initialized and activated. With the former behavior, the driver could crash
when netpoll was calling ndo_poll_controller.
Signed-off-by: Merav Sicron <meravs@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With a low enough MSS on the link partner and TSO enabled locally, the
networking stack can periodically send a very large (e.g. 64KB) TCP
message for which the driver will attempt to use more Tx descriptors than
are available by default in the Tx ring. This is due to a workaround in
the code that imposes a limit of only 4 MSS-sized segments per descriptor
which appears to be a carry-over from the older e1000 driver and may be
applicable only to some older PCI or PCIx parts which are not supported in
e1000e. When the driver gets a message that is too large to fit across the
configured number of Tx descriptors, it stops the upper stack from queueing
any more and gets stuck in this state. After a timeout, the upper stack
assumes the adapter is hung and calls the driver to reset it.
Remove the unnecessary limitation of using up to only 4 MSS-sized segments
per Tx descriptor, and put in a hard failure test to catch when attempting
to check for message sizes larger than would fit in the whole Tx ring.
Refactor the remaining logic that limits the size of data per Tx descriptor
from a seemingly arbitrary 8KB to a limit based on the dynamic size of the
Tx packet buffer as described in the hardware specification.
Also, fix the logic in the check for space in the Tx ring for the next
largest possible packet after the current one has been successfully queued
for transmit, and use the appropriate defines for default ring sizes in
e1000_probe instead of magic values.
This issue goes back to the introduction of e1000e in 2.6.24 when it was
split off from e1000.
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Stable <stable@vger.kernel.org> [2.6.24+]
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit -
"b852b72 gianfar: fix bug caused by
87c288c6e9aa31720b72e2bc2d665e24e1653c3e"
disables by default (on mac init) the hw vlan tag insertion.
The "features" flags were not updated to reflect this, and
"ethtool -K" shows tx-vlan-offload to be "on" by default.
Cc: Sebastian Poehn <sebastian.poehn@belden.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Against -net.
In the patch "netpoll: re-enable irq in poll_napi()", I tried to
fix the following warning:
[100718.051041] ------------[ cut here ]------------
[100718.051048] WARNING: at kernel/softirq.c:159 local_bh_enable_ip+0x7d/0xb0()
(Not tainted)
[100718.051049] Hardware name: ProLiant BL460c G7
...
[100718.051068] Call Trace:
[100718.051073] [<ffffffff8106b747>] ? warn_slowpath_common+0x87/0xc0
[100718.051075] [<ffffffff8106b79a>] ? warn_slowpath_null+0x1a/0x20
[100718.051077] [<ffffffff810747ed>] ? local_bh_enable_ip+0x7d/0xb0
[100718.051080] [<ffffffff8150041b>] ? _spin_unlock_bh+0x1b/0x20
[100718.051085] [<ffffffffa00ee974>] ? be_process_mcc+0x74/0x230 [be2net]
[100718.051088] [<ffffffffa00ea68c>] ? be_poll_tx_mcc+0x16c/0x290 [be2net]
[100718.051090] [<ffffffff8144fe76>] ? netpoll_poll_dev+0xd6/0x490
[100718.051095] [<ffffffffa01d24a5>] ? bond_poll_controller+0x75/0x80 [bonding]
[100718.051097] [<ffffffff8144fde5>] ? netpoll_poll_dev+0x45/0x490
[100718.051100] [<ffffffff81161b19>] ? ksize+0x19/0x80
[100718.051102] [<ffffffff81450437>] ? netpoll_send_skb_on_dev+0x157/0x240
by reenabling IRQ before calling ->poll, but it seems more
problems are introduced after that patch:
http://ozlabs.org/~akpm/stuff/IMG_20120824_122054.jpghttp://marc.info/?l=linux-netdev&m=134563282530588&w=2
So it is safe to fix be2net driver code directly.
This patch reverts the offending commit and fixes be_poll() by
avoid disabling BH there, this is okay because be_poll()
can be called either by poll_napi() which already disables
IRQ, or by net_rx_action() which already disables BH.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Reported-by: Sylvain Munaut <s.munaut@whatever-company.com>
Cc: Sylvain Munaut <s.munaut@whatever-company.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Miller <davem@davemloft.net>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Tested-by: Sylvain Munaut <s.munaut@whatever-company.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
Simple fix for a braino. Please also queue this for the 3.4 and 3.5
stable series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds "#ifndef __<header>_H" for protecting header from double
inclusion.
Signed-off-by: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Hacked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ETHTOOL_GRXCLSRULE returns filters for a TCP/IPv4 or UDP/IPv4 4-tuple
with source and destination swapped.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
This patch fixes the name of the macro used to mask the
mmc interrupt: erroneously it was used: MMC_DEFAUL_MASK.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Erroneously the DWMAC_CORE_3_40 was set to 34 instead of 0x34.
This can generate problems when run on old chips because
the driver assumes that there are the extra 16 regs available
for perfect filtering.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Gianni Antoniazzi <gianni.antoniazzi-ext@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking update from David Miller:
"A couple weeks of bug fixing in there. The largest chunk is all the
broken crap Amerigo Wang found in the netpoll layer."
1) netpoll and it's users has several serious bugs:
a) uses GFP_KERNEL with locks held
b) interfaces requiring interrupts disabled are called with them
enabled
c) and vice versa
d) VLAN tag demuxing, as per all other RX packet input paths, is not
applied
All from Amerigo Wang.
2) Hopefully cure the ipv4 mapped ipv6 address TCP early demux bugs for
good, from Neal Cardwell.
3) Unlike AF_UNIX, AF_PACKET sockets don't set a default credentials
when the user doesn't specify one explicitly during sendmsg().
Instead we attach an empty (zero) SCM credential block which is
definitely not what we want. Fix from Eric Dumazet.
4) IPv6 illegally invokes netdevice notifiers with RCU lock held, fix
from Ben Hutchings.
5) inet_csk_route_child_sock() checks wrong inet options pointer, fix
from Christoph Paasch.
6) When AF_PACKET is used for transmit, packet loopback doesn't behave
properly when a socket fanout is enabled, from Eric Leblond.
7) On bluetooth l2cap channel create failure, we leak the socket, from
Jaganath Kanakkassery.
8) Fix all the netprio file handling bugs found by Al Viro, from John
Fastabend.
9) Several error return and NULL deref bug fixes in networking drivers
from Julia Lawall.
10) A large smattering of struct padding et al. kernel memory leaks to
userspace found of Mathias Krause.
11) Conntrack expections in netfilter can access an uninitialized timer,
fix from Pablo Neira Ayuso.
12) Several netfilter SIP tracker bug fixes from Patrick McHardy.
13) IPSEC ipv6 routes are not initialized correctly all the time,
resulting in an OOPS in inet_putpeer(). Also from Patrick McHardy.
14) Bridging does rcu_dereference() outside of RCU protected area, from
Stephen Hemminger.
15) Fix routing cache removal performance regression when looking up
output routes that have a local destination. From Zheng Yan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (87 commits)
af_netlink: force credentials passing [CVE-2012-3520]
ipv4: fix ip header ident selection in __ip_make_skb()
ipv4: Use newinet->inet_opt in inet_csk_route_child_sock()
tcp: fix possible socket refcount problem
net: tcp: move sk_rx_dst_set call after tcp_create_openreq_child()
net/core/dev.c: fix kernel-doc warning
netconsole: remove a redundant netconsole_target_put()
net: ipv6: fix oops in inet_putpeer()
net/stmmac: fix issue of clk_get for Loongson1B.
caif: Do not dereference NULL in chnl_recv_cb()
af_packet: don't emit packet on orig fanout group
drivers/net/irda: fix error return code
drivers/net/wan/dscc4.c: fix error return code
drivers/net/wimax/i2400m/fw.c: fix error return code
smsc75xx: add missing entry to MAINTAINERS
net: qmi_wwan: new devices: UML290 and K5006-Z
net: sh_eth: Add eth support for R8A7779 device
netdev/phy: skip disabled mdio-mux nodes
dt: introduce for_each_available_child_of_node, of_get_next_available_child
net: netprio: fix cgrp create and write priomap race
...
When getting clock, give a chance to the CPUs without DT support,
which use Common Clock Framework, such as Loongson1B.
Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- IPoIB fixes for regressions introduced by path database conversion
- mlx4 fixes for bugs with large memory systems and regressions from SR-IOV patches
- RDMA CM fix for passing bad event up to userspace
- Other minor fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=hN/H
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma fixes from Roland Dreier:
"Grab bag of InfiniBand/RDMA fixes:
- IPoIB fixes for regressions introduced by path database conversion
- mlx4 fixes for bugs with large memory systems and regressions from
SR-IOV patches
- RDMA CM fix for passing bad event up to userspace
- Other minor fixes"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Check iboe netdev pointer before dereferencing it
mlx4_core: Clean up buddy bitmap allocation
mlx4_core: Fix integer overflow issues around MTT table
mlx4_core: Allow large mlx4_buddy bitmaps
IB/srp: Fix a race condition
IB/qib: Fix error return code in qib_init_7322_variables()
IB: Fix typos in infiniband drivers
IB/ipoib: Fix RCU pointer dereference of wrong object
IB/ipoib: Add missing locking when CM object is deleted
RDMA/ucma.c: Fix for events with wrong context on iWARP
RDMA/ocrdma: Don't call vlan_dev_real_dev() for non-VLAN netdevs
IB/mlx4: Fix possible deadlock on sm_lock spinlock
- Use kcalloc() / vzalloc() instead of an extra bitmap_zero().
- Add __GFP_NOWARN to kcalloc() since we'll try vzalloc() if it fails.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix some issues around int variables used in data structures related
to memory registration.
Handle int overflow in mlx4_init_icm_table by using a u64 intermediate
variable and changing struct mlx4_icm_table num_obj field to be u32.
Change some more fields/variables to use u32 instead of int to prevent
a case where the variable becomes negative when bit 31 is set.
Also subtract log_mtts_per_seg from the exponent when computing
num_mtt, since its added later on in that very same code area.
This and the previous commit fixes some issues which actually prevent
commit db5a7a65c0 ("mlx4_core: Scale size of MTT table with system
RAM") from working. Now, when the number of MTTs is scaled with the
size of the RAM we can map up to 8TB.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
mlx4_buddy_init uses kmalloc() to allocate bitmaps, which fails when
the required size is beyond the max supported value (or when memory is
too fragmented to handle a huge allocation). Extend this to use use
vmalloc() if kmalloc() fails, and take that into account when freeing
the bitmaps as well.
This fixes a driver load failure when log num mtt is 26 or higher, and
is a step in the direction of allowing to register huge amounts of
memory on large memory systems.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Convert a 0 error return code to a negative one, as returned elsewhere in the
function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@
(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
when != ret = e3
*if (x == NULL || ...)
{
... when != ret = e4
* return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert a 0 error return code to a negative one, as returned elsewhere in the
function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@
(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
when != ret = e3
*if (x == NULL || ...)
{
... when != ret = e4
* return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the NULL test is necessary, the initialization involving a dereference of
the tested value should be moved after the NULL test.
The sematic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@
- T i = E->fld;
+ T i;
... when != E
when != i
if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following compiler warnings:
- drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c:2908:3: warning: comparison
of distinct pointer types lacks a cast [enabled by default]
- drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c:1709:7: warning: comparison
of distinct pointer types lacks a cast [enabled by default]
Signed-off-by: Joren Van Onder <joren.vanonder@gmail.com>
Acked-By: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds missing braces around the 10gig link check to include the check for KR support.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Reported-by: Sascha Wildner <saw@online.de>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During probe, every function probed clears the recovery registers from
all functions on its path - thus signaling that given a future recovery
event, there will be no need to wait for those functions.
This is a flawed behaviour - each function should only be responsible
for its own bit.
Since this registers are handled during the load/unload routines,
this cleanup is removed altogether.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing previous driver unload flow is flawed, causing the probe of
functions reaching the 'uncommon fork' in flr-capable devices to fail.
This patch resolves this, as well as fixing the flow for hypervisors which
disable flr capabilities from functions as they pass them as PDA to VMs,
as we cannot base the flow on the pci configuration space.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like the register defines for DCA were never updated after going from
82575 to 82576. This change addresses that by updating the defines.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
This patch resolves a "BUG: unable to handle kernel paging request at ..."
oops while dumping packet data. The issue occurs with IOMMU enabled due to
the address provided by phys_to_virt().
This patch avoids phys_to_virt() by using skb->data and the address of the
pages allocated for Rx.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
This patch resolves a "BUG: unable to handle kernel paging request at ..."
oops while dumping packet data. The issue occurs with IOMMU enabled due to
the address provided by phys_to_virt().
This patch avoids phys_to_virt() by making using skb->data and the address
of the pages allocated for Rx.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Driver probe functions are generally __devinit so they will be
discarded after initialization for non-hotplug kernels.
This was found by a new warning after patch 6a228452d "stmmac: Add
device-tree support" adds a new __devinit function that is called
from stmmac_pltfr_probe.
Without this patch, building socfpga_defconfig results in:
WARNING: drivers/net/ethernet/stmicro/stmmac/stmmac.o(.text+0x5d4c): Section mismatch in reference from the function stmmac_pltfr_probe() to the function .devinit.text:stmmac_probe_config_dt()
The function stmmac_pltfr_probe() references
the function __devinit stmmac_probe_config_dt().
This is often because stmmac_pltfr_probe lacks a __devinit
annotation or the annotation of stmmac_probe_config_dt is wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The #ifdefs regarding CONFIG_ARCH_LPC32XX_MII_SUPPORT and
CONFIG_ARCH_LPC32XX_IRAM_FOR_NET are obsolete since the symbols have been
removed from Kconfig and replaced by devicetree based configuration.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some 8086:10c9 NICs have a problem completing the ethtool loopback test.
The result looks like this:
ethtool -t eth1
The test result is FAIL
The test extra info:
Register test (offline) 0
Eeprom test (offline) 0
Interrupt test (offline) 0
Loopback test (offline) 13
Link test (on/offline) 0
A bisect clearly points to commit a95a07445e.
However that seems to only trigger the bug. While adding some printk the
problem disappeared, so this might be a timing issue. After some trial and
error I discovered that adding a small delay just before igb_write_phy_reg()
in igb_integrated_phy_loopback() allows the loopback test to succeed.
I was unable to figure out the root cause so far but I expect it to be
somewhere in the following executing path
igb_integrated_phy_loopback
->igb_write_phy_reg_igp
->igb_write_phy_reg_mdic
->igb_acquire_phy_82575
->igb_acquire_swfw_sync_82575
The problem could only be observed on 8086:10c9 NICs so far and not all
of them show the behaviour. I did not restrict the workaround to this
type of NIC as it should do no harm to other igb NICs.
With the patch below the loopback test succeeded 500 times in a row
using a NIC that would otherwise fail.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
A bus trace shows that while executing e1000e_down, TCTL is cleared except
for the PSP bit. This occurs while in the middle of fetching a TSO packet
since the Tx packet buffer is full at that point. Before the device is
reset, the e1000_watchdog_task starts to run from the middle (it was
apparently pre-empted earlier, although that is not in the trace) and sets
TCTL.EN. At that point, 82571 transmits the corrupted packet, apparently
because TCTL.MULR was cleared in the middle of fetching a packet, which is
forbidden.
Driver should just clear TCTL.EN in e1000_reset_hw_82571 instead of
clearing the entire register, so as not to change any settings in the
middle of fetching a packet.
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Found that commit d478eb44 was a bad commit.
If the link partner is transmitting codeword (even if NULL codeword),
then the RXCW.C bit will be set so check for RXCW.CW is unnecessary.
Ref: RH BZ 840642
Reported-by: Fabio Futigami <ffutigam@redhat.com>
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
CC: Marcelo Ricardo Leitner <mleitner@redhat.com>
CC: stable <stable@vger.kernel.org> [2.6.38+]
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
When building with ixp4xx_eth and ptp_ixp46x as module, one is getting the
following error:
ERROR: "ixp46x_phc_index" [drivers/ptp/ptp_ixp46x.ko] undefined!
This has been introduced by commit 509a7c2572.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even when they go beyond 80 characters, user visible strings should be
on one line to make them easy to grep for.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
In the original code
...
if ((adapter->hw.mac.type == e1000_i210)
|| (adapter->hw.mac.type == e1000_i210)) {
...
the second check of 'adapter->hw.mac.type' is pointless since it tests
for the exact same value as the first.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Move nvm invalid size check to before size assigned by mac_type for
82575 and later parts in get_invariants function. This fixes a problem
found on some 82576 devices where the part will not initialize because
the nvm_read function pointer ends up getting assigned to the incorrect
function.
Reported By: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Port1=Eth, Port2=IB restriction is no longer required.
Having RoCE, there will always rdma port initialized over ConnectX
physical port, no matter whether the link layer is IB or Ethernet.
So we always have dual port IB device.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing the ring->blocked flag, it is redundant and leads to a race:
We close the TX queue and then set the "blocked" flag.
Between those 2 operations the completion function can check the "blocked"
flag, sees that it is 0, and wouldn't open the TX queue.
Using netif_tx_queue_stopped to check the state of the queue to avoid this race.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Should NOT check SMAC=DMAC when:
1. loopback is turned on
2. validate_loopback is true.
Fixed it accordingly.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Missing a CR in printk causes 2 messages printed in one line.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bnx2x_mcast_enqueue_cmd() we'll leak the memory allocated to
'new_cmd' if we hit the deafault case of the 'switch (cmd)'.
Add a 'kfree(new_cmd)' to that case to avoid the leak.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently an skb requiring TSO may not fit within a minimum-size TX
queue. The TX queue selected for the skb may stall and trigger the TX
watchdog repeatedly (since the problem skb will be retried after the
TX reset). This issue is designated as CVE-2012-3412.
Set the maximum number of TSO segments for our devices to 100. This
should make no difference to behaviour unless the actual MSS is less
than about 700. Increase the minimum TX queue size accordingly to
allow for 2 worst-case skbs, so that there will definitely be space
to add an skb after we wake a queue.
To avoid invalidating existing configurations, change
efx_ethtool_set_ringparam() to fix up values that are too small rather
than returning -EINVAL.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge Andrew's second set of patches:
- MM
- a few random fixes
- a couple of RTC leftovers
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (120 commits)
rtc/rtc-88pm80x: remove unneed devm_kfree
rtc/rtc-88pm80x: assign ret only when rtc_register_driver fails
mm: hugetlbfs: close race during teardown of hugetlbfs shared page tables
tmpfs: distribute interleave better across nodes
mm: remove redundant initialization
mm: warn if pg_data_t isn't initialized with zero
mips: zero out pg_data_t when it's allocated
memcg: gix memory accounting scalability in shrink_page_list
mm/sparse: remove index_init_lock
mm/sparse: more checks on mem_section number
mm/sparse: optimize sparse_index_alloc
memcg: add mem_cgroup_from_css() helper
memcg: further prevent OOM with too many dirty pages
memcg: prevent OOM with too many dirty pages
mm: mmu_notifier: fix freed page still mapped in secondary MMU
mm: memcg: only check anon swapin page charges for swap cache
mm: memcg: only check swap cache pages for repeated charging
mm: memcg: split swapin charge function into private and public part
mm: memcg: remove needless !mm fixup to init_mm when charging
mm: memcg: remove unneeded shmem charge type
...
Pull networking update from David S. Miller:
"I think Eric Dumazet and I have dealt with all of the known routing
cache removal fallout. Some other minor fixes all around.
1) Fix RCU of cached routes, particular of output routes which require
liberation via call_rcu() instead of call_rcu_bh(). From Eric
Dumazet.
2) Make sure we purge net device references in cached routes properly.
3) TG3 driver bug fixes from Michael Chan.
4) Fix reported 'expires' value in ipv6 routes, from Li Wei.
5) TUN driver ioctl leaks kernel bytes to userspace, from Mathias
Krause."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (22 commits)
ipv4: Properly purge netdev references on uncached routes.
ipv4: Cache routes in nexthop exception entries.
ipv4: percpu nh_rth_output cache
ipv4: Restore old dst_free() behavior.
bridge: make port attributes const
ipv4: remove rt_cache_rebuild_count
net: ipv4: fix RCU races on dst refcounts
net: TCP early demux cleanup
tun: Fix formatting.
net/tun: fix ioctl() based info leaks
tg3: Update version to 3.124
tg3: Fix race condition in tg3_get_stats64()
tg3: Add New 5719 Read DMA workaround
tg3: Fix Read DMA workaround for 5719 A0.
tg3: Request APE_LOCK_PHY before PHY access
ipv6: fix incorrect route 'expires' value passed to userspace
mISDN: Bugfix only few bytes are transfered on a connection
seeq: use PTR_RET at init_module of driver
bnx2x: remove cast around the kmalloc in bnx2x_prev_mark_path
ipv4: clean up put_child
...
The skb->pfmemalloc flag gets set to true iff during the slab allocation
of data in __alloc_skb that the the PFMEMALLOC reserves were used. If
page splitting is used, it is possible that pages will be allocated from
the PFMEMALLOC reserve without propagating this information to the skb.
This patch propagates page->pfmemalloc from pages allocated for fragments
to the skb.
It works by reintroducing and expanding the skb_alloc_page() API to take
an skb. If the page was allocated from pfmemalloc reserves, it is
automatically copied. If the driver allocates the page before the skb, it
should call skb_propagate_pfmemalloc() after the skb is allocated to
ensure the flag is copied properly.
Failure to do so is not critical. The resulting driver may perform slower
if it is used for swap-over-NBD or swap-over-NFS but it should not result
in failure.
[davem@davemloft.net: API rename and consistency]
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Neil Brown <neilb@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Eric B Munson <emunson@mgebm.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge Andrew's first set of patches:
"Non-MM patches:
- lots of misc bits
- tree-wide have_clk() cleanups
- quite a lot of printk tweaks. I draw your attention to "printk:
convert the format for KERN_<LEVEL> to a 2 byte pattern" which
looks a bit scary. But afaict it's solid.
- backlight updates
- lib/ feature work (notably the addition and use of memweight())
- checkpatch updates
- rtc updates
- nilfs updates
- fatfs updates (partial, still waiting for acks)
- kdump, proc, fork, IPC, sysctl, taskstats, pps, etc
- new fault-injection feature work"
* Merge emailed patches from Andrew Morton <akpm@linux-foundation.org>: (128 commits)
drivers/misc/lkdtm.c: fix missing allocation failure check
lib/scatterlist: do not re-write gfp_flags in __sg_alloc_table()
fault-injection: add tool to run command with failslab or fail_page_alloc
fault-injection: add selftests for cpu and memory hotplug
powerpc: pSeries reconfig notifier error injection module
memory: memory notifier error injection module
PM: PM notifier error injection module
cpu: rewrite cpu-notifier-error-inject module
fault-injection: notifier error injection
c/r: fcntl: add F_GETOWNER_UIDS option
resource: make sure requested range is included in the root range
include/linux/aio.h: cpp->C conversions
fs: cachefiles: add support for large files in filesystem caching
pps: return PTR_ERR on error in device_create
taskstats: check nla_reserve() return
sysctl: suppress kmemleak messages
ipc: use Kconfig options for __ARCH_WANT_[COMPAT_]IPC_PARSE_VERSION
ipc: compat: use signed size_t types for msgsnd and msgrcv
ipc: allow compat IPC version field parsing if !ARCH_WANT_OLD_COMPAT_IPC
ipc: add COMPAT_SHMLBA support
...
Santiago Leon
