The module was initializing completions whenever it was going to wait on
them, and not when the completion was allocated. This is incorrect
according to the completion docs:
Calling init_completion() on the same completion object twice is
most likely a bug [...]
Re-initialization is also unnecessary because the module never uses
complete_all(). Fix this by only ever initializing the completion a
single time, and log if the completions are not consumed as intended
(this is not a fatal problem, but should not go unnoticed).
Signed-off-by: George Hilliard <thirtythreeforty@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These values are not referred to anywhere else in the kernel. Card
detect is controlled by the device tree property "mediatek,cd-poll",
and there is no driver support for eMMC whatsoever.
Signed-off-by: George Hilliard <thirtythreeforty@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The buffer descriptor setup loop is correct only if it is setting up at
least one bd struct. Besides, there is an error if dma_map_sg() returns
0, which is possible and must be handled.
Additionally, remove the BUG_ON() checking sglen, which is unnecessary
because we configure DMA with that constraint during init.
Signed-off-by: George Hilliard <thirtythreeforty@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel complained:
[ 510.277151] WARNING: CPU: 0 PID: 395 at fs/proc/generic.c:360 proc_register+0xf0/0x108
[ 510.292891] proc_dir_entry '/proc/msdc_debug' already registered
when doing a modprobe/rmmod/modprobe of this module if debug messages
are compiled in. Fix this by removing the proc entry when the module is
unloaded.
Signed-off-by: George Hilliard <thirtythreeforty@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A failure while processing the start command could cause dma_unmap_sg()
to be called without first calling dma_map_sg().
Since calling dma_unmap_sg() is only needed when data != NULL, move the
unmap call into the corresponding if {} block.
Signed-off-by: George Hilliard <thirtythreeforty@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Obvious typo. It is specified as BURST in the datasheet.
Signed-off-by: George Hilliard <thirtythreeforty@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to delay notifying the mmc layer. Schedule the delayed
work to run immediately.
Signed-off-by: George Hilliard <thirtythreeforty@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is set once during initialization and never changed. Don't bother
setting it again in the interrupt handler.
Signed-off-by: George Hilliard <thirtythreeforty@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When waiting on completions, use the _io variant so the caller is
charged as using I/O.
This should have no effect on the module's functionality, only improve
CPU accounting.
Signed-off-by: George Hilliard <thirtythreeforty@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver previously grabbed the SD pins for itself, ignoring the pin
controller. Remove this, and allow the pinctrl subsystem to set up the
pins using the device tree mappings. This allows this driver to work on
related devices that have a different pin controller mapping, such as
the MT7688. The hardcoded bit index was incorrect on that device.
The driver now needs a pin controller reference in its device tree node:
sdhci: /* ... */ {
compatible = "ralink,mt7620-sdhci";
pinctrl-names = "default";
pinctrl-0 = <&sdhci_pins>;
// ...
};
This change could break SD controller functionality on existing devices
whose device trees do not specify a pin controller and state for the SD
node.
Signed-off-by: George Hilliard <thirtythreeforty@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Modify the return type of the function msdc_do_command to static int
as the member error of the structure struct mmc_command is of type int.
Signed-off-by: Bhanusree Pola <bhanusreemahesh@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return the value directly instead of storing it in local variable err.
Remove the unused local variable err.
The semantic patch that fixes the first part of the problem is as follows
// <smpl>
@@
local idexpression ret;
expression e;
@@
-ret =
+return
e;
-return ret;
// </smpl>
Signed-off-by: Bhanusree Pola <bhanusreemahesh@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use BIT(x) instead of (1<<x), reported by checkpatch.pl.
Signed-off-by: Bhanusree Pola <bhanusreemahesh@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove including <linux/version.h> that don't need it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These drivers can be useful on other MT76xx SoCs, which have compatible
peripherals. The drivers were selectable in Kconfig, but they were
quietly excluded from the build because the SOC_MT7621 chip was not
selected. So, make the Makefiles use the same flags as Kconfig for
these drivers.
mt7621-dma and mt7621-dts are left alone because they truly do require
that SoC.
I have personally confirmed that the mt7621-spi driver works on the
MT7688, which was what prompted this change.
Cc: linux-kernel@vger.kernel.org
Cc: devel@driverdev.osuosl.org
Cc: NeilBrown <neil@brown.name>
Cc: sergio.paracuellos@gmail.com
Signed-off-by: George Hilliard <thirtythreeforty@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changed "avaiable" to "available" and "interupt" to "interrupt".
Signed-off-by: Jona Crasselt <jona.crasselt@fau.de>
Signed-off-by: Felix Windsheimer <felix.windsheimer@fau.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix some comment-related issues reported by checkpatch.pl:
- Block comments use * on subsequent lines
- Block comments use a trailing */ on a separate line
Signed-off-by: Jona Crasselt <jona.crasselt@fau.de>
Signed-off-by: Felix Windsheimer <felix.windsheimer@fau.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 2a54e3259e ("staging: mt7621-mmc: Remove #if 0 blocks in sd.c")
does not completely remove an #if 0 block in sd.c. This causes the function
msdc_select_clksrc() which was eariler not compiled, to be compiled.
That causes an error - MSDC_CLKSRC_REG is not defined.
This patch completely removes the #if 0 block
Reported-by: NeilBrown <neil@brown.name>
Fixes: 2a54e3259e ("staging: mt7621-mmc: Remove #if 0 blocks in sd.c")
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Reviewed-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cmd_buf is only used when MT6575_SD_DEBUG is defined.
So only declare it in that case.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
<linux/interrupt.h> is sometimes included by other include files,
and sometimes not, depending on config, particularly CONFIG_HIGHMEM.
So include it explicitly rather than relying on implicit inclusion.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit f8c55dc6e8 ("MIPS: use generic dma noncoherent ops for
simple noncoherent platforms") changed MIPS dma handling, the mmc
driver fails because it doesn't have a dma mask is set.
So set the correct dma mask.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Correct the following warning from checkpatch.pl:
WARNING: Missing a blank line after declarations
+ struct msdc_host *host = mmc_priv(mmc);
+ msdc_pm(state, (void *)host);
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@protonmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace explicit shifting with BIT macro in dbg.h.
Issue found by checkpatch.
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes lines over 80 characters in dbg.h.
Issue found by checkpatch.
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes lines over 80 characters in dbg.c.
Issue found by checkpatch.
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add blank line after declaration.
Reported by checkpatch.
Signed-off-by: Jaakko Tyynismaa <jaakko.tyynismaa@hotmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes #if 0 code blocks and usages of
functions defined in the #if 0 blocks in dbg.h.
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes #if 0 code blocks and usages of
functions defined in the #if 0 blocks in dbg.c
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes #if 0 code blocks and usages of
functions defined in the #if 0 blocks in sd.c.
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the macro msdc_irq_restore() and replaces its
usage with call to the function called in the macro definition.
Issue found by checkpatch.
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace calls to `printk` with `dev_info` and `pr_err`
Issues found with checkpatch.pl
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace comparisons of a variable 'x' to NULL with
either 'x' or '!x'.
Issues found with checkpatch.pl
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unnecessary braces from one line 'if' statements.
Issues found with checkpatch.pl
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes IRQ_MSG() and its users as currently it is a no-op.
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace all usages of ERR_MSG with with dev_<level> without __func__
or __LINE__ or current->comm and current->pid. Remove the do {}
while(0) loop for the single statement macro. Delete commented
ERR_MSG() usage. Drop ERR_MSG from dbg.h. Issue found by checkpatch.
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes N_MSG() and all its users since it is a no-op.
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removed all usages of INIT_MSG and dropped it from dbg.h.
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Placed a check for the return value of sscanf. -EINVAL is returned if
the value is anything other than expected. Reported by checkpatch.pl
Signed-off-by: Sumit Pundir <pundirsumit11@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace explicit shifting with BIT macro in board.h.
Issue found by checkpatch.
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch fixes the following issue:
WARNING: printk() should include KERN_<LEVEL> facility level
Signed-off-by: Sergej Perschin <ser.perschin@gmail.com>
Signed-off-by: Marcel Budoj <marcel.budoj@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The response type of the SD_APP_OP_COND command is correctly
determined using the mmc_resp_type macro, because the only use of that
opcode, mmc_send_app_op_cond, correctly places MMC_RSP_R3 in cmd.flags.
So there is no need to treat that opcode separately.
Signed-off-by: Christian Lütke-Stetzkamp <christian@lkamp.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The response type of the MMC_SEND_OP_COND command is correctly
determined using the mmc_resp_type macro, because the only use of that
opcode, mmc_send_op_cond, correctly places MMC_RSP_R3 in cmd.flags.
So there is no need to treat that opcode separately.
Signed-off-by: Christian Lütke-Stetzkamp <christian@lkamp.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
George Hilliard