mirror of https://gitee.com/openkylin/linux.git
166 Commits
| Author | SHA1 | Message | Date |
|---|---|---|---|
Greg Kroah-Hartman
|
b2e312061c |
First round of IIO fixes for the 4.14 cycle
Note this includes fixes from recent merge window. As such the tree
is based on top of a prior staging/staging-next tree.
* iio core
- return and error for a failed read_reg debugfs call rather than
eating the error.
* ad7192
- Use the dedicated reset function in the ad_sigma_delta library
instead of an spi transfer with the data on the stack which
could cause problems with DMA.
* ad7793
- Implement a dedicate reset function in the ad_sigma_delta library
and use it to correctly reset this part.
* bme280
- ctrl_reg write must occur after any register writes
for updates to take effect.
* mcp320x
- negative voltage readout was broken.
- Fix an oops on module unload due to spi_set_drvdata not being called
in probe.
* st_magn
- Fix the data ready line configuration for the lis3mdl. It is not
configurable so the st_magn core was assuming it didn't exist
and so wasn't consuming interrupts resulting in an unhandled
interrupt.
* stm32-adc
- off by one error on max channels checking.
* stm32-timer
- preset should not be buffered - reorganising register writes avoids
this.
- fix a corner case in which write preset goes wrong when a timer is
used first as a trigger then as a counter with preset. Odd case but
you never know.
* ti-ads1015
- Fix setting of comparator polarity by fixing bitfield definition.
* twl4030
- Error path handling fix to cleanup in event of regulator
registration failure.
- Disable the vusb3v1 regulator correctly in error handling
- Don't paper over a regulator enable failure.
-----BEGIN PGP SIGNATURE-----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=CcjQ
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.14a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First round of IIO fixes for the 4.14 cycle
Note this includes fixes from recent merge window. As such the tree
is based on top of a prior staging/staging-next tree.
* iio core
- return and error for a failed read_reg debugfs call rather than
eating the error.
* ad7192
- Use the dedicated reset function in the ad_sigma_delta library
instead of an spi transfer with the data on the stack which
could cause problems with DMA.
* ad7793
- Implement a dedicate reset function in the ad_sigma_delta library
and use it to correctly reset this part.
* bme280
- ctrl_reg write must occur after any register writes
for updates to take effect.
* mcp320x
- negative voltage readout was broken.
- Fix an oops on module unload due to spi_set_drvdata not being called
in probe.
* st_magn
- Fix the data ready line configuration for the lis3mdl. It is not
configurable so the st_magn core was assuming it didn't exist
and so wasn't consuming interrupts resulting in an unhandled
interrupt.
* stm32-adc
- off by one error on max channels checking.
* stm32-timer
- preset should not be buffered - reorganising register writes avoids
this.
- fix a corner case in which write preset goes wrong when a timer is
used first as a trigger then as a counter with preset. Odd case but
you never know.
* ti-ads1015
- Fix setting of comparator polarity by fixing bitfield definition.
* twl4030
- Error path handling fix to cleanup in event of regulator
registration failure.
- Disable the vusb3v1 regulator correctly in error handling
- Don't paper over a regulator enable failure.
|
|
|
Colin Parker
|
4b1f0c31f9 |
IIO: BME280: Updates to Humidity readings need ctrl_reg write!
The ctrl_reg register needs to be written after any write to the humidity registers. The value written to the ctrl_reg register does not necessarily need to change, but a write operation must occur. The regmap_update_bits functions will not write to a register if the register value matches the value to be written. This saves unnecessary bus operations. The change in this patch forces a bus write during the chip_config operation by switching to regmap_write_bits. This will fix issues where the Humidity Sensor Oversampling bits are not updated after initialization. Signed-off-by: Colin Parker <colin.parker@aclima.io> Acked-by: Andreas Klinger <ak@it-klinger.de> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> |
|
|
Greg Kroah-Hartman
|
8439a69e72 |
Merge 4.13-rc7 into staging-next
We want the staging and iio fixes in here to handle the merge issues. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
|
|
Greg Kroah-Hartman
|
5e47adb906 |
Second set of IIO new device support, features and cleanup for the 4.14 cycle.
New device support:
* ak8974
- support the AMI306.
* st_magnetometer
- add support for the LIS2MDL with bindings.
* rockchip-saradc
- add binding for rv1108 SoC (no driver change).
* srf08
- add srf02 (i2c only) and srf10 support.
* stm32-timer
- support for the STM32H7 to existing driver.
Features:
* tools
- move over to the tools buildsystem rather than hand rolling.
- add an install section to the build.
* ak8974
- use serial number to add device randomness.
- add AMI306 calibration data output.
* ccs811
- triggered buffer support.
* srf08
- add a device tree table as the old style i2c probing is going away,
- add triggered buffer support
* st32-adc
- add optional st,min-sample-time-nsecs binding to allow control of
sampling against analog circuitry.
* stm32-timer
- add output compare triggers.
* ti-ads1015
- add threshold event support.
* ti-ads7950
- Allow use on ACPI platforms including providing a default reference
voltage as there is no way to obtain this on ACPI currently.
Cleanup and fixes:
* ad7606
- fix an error return code in probe.
* ads1015
- fix incorrect data rate setting update when capture in progress,
- fix wrong scale information for the ADS1115,
- make conversions work when CONFIG_PM is not set,
- make sure we don't get a stale result after a runtime resume by
ensuring we wait long enough,
- avoid returning a false error form the buffer setup callbacks,
- add enough wait time to get the correct conversion,
- remove an unnecessary config register update,
- add a helper to set conversion mode reducing repeated boilerplate,
- use devm_iio_triggered_buffer_setup to simplify error and remove
paths,
- use iio_device_claim_direct_mode instead of opencoding the same.
* ak8974
- mark the INT_CLEAR register as precious to prevent debugfs access.
* apds9300
- constify the i2c_device_id.
* at91-sama5 adc
- add missing Kconfig dependency.
* bma180 accel
- constify the i2c_device_id.
* rockchip_saradc
- explicitly request exclusive reset control as part of the reset rework
on going throughout the kernel.
* st_accel
- fix drdy configuration for a load of accelerometers that only have
the int1 line. Fix is unimportant as presumably no deviec tree actually
used the non existent hardware line.
* st_pressure
- fix drdy configuration for LPS22HB and LPS25H by dropping int2 support
as they don't have this. Fix is unimportant as presumably no device tree
actually used the non existent hardware line.
* stm32-dac
- explicitly request exclusive reset control (part of reset being reworked).
* tsl2583
- constify the i2c_device_id.
* xadc
- coding style fixes.
-----BEGIN PGP SIGNATURE-----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=b6g8
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.14b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of IIO new device support, features and cleanup for the 4.14 cycle.
New device support:
* ak8974
- support the AMI306.
* st_magnetometer
- add support for the LIS2MDL with bindings.
* rockchip-saradc
- add binding for rv1108 SoC (no driver change).
* srf08
- add srf02 (i2c only) and srf10 support.
* stm32-timer
- support for the STM32H7 to existing driver.
Features:
* tools
- move over to the tools buildsystem rather than hand rolling.
- add an install section to the build.
* ak8974
- use serial number to add device randomness.
- add AMI306 calibration data output.
* ccs811
- triggered buffer support.
* srf08
- add a device tree table as the old style i2c probing is going away,
- add triggered buffer support
* st32-adc
- add optional st,min-sample-time-nsecs binding to allow control of
sampling against analog circuitry.
* stm32-timer
- add output compare triggers.
* ti-ads1015
- add threshold event support.
* ti-ads7950
- Allow use on ACPI platforms including providing a default reference
voltage as there is no way to obtain this on ACPI currently.
Cleanup and fixes:
* ad7606
- fix an error return code in probe.
* ads1015
- fix incorrect data rate setting update when capture in progress,
- fix wrong scale information for the ADS1115,
- make conversions work when CONFIG_PM is not set,
- make sure we don't get a stale result after a runtime resume by
ensuring we wait long enough,
- avoid returning a false error form the buffer setup callbacks,
- add enough wait time to get the correct conversion,
- remove an unnecessary config register update,
- add a helper to set conversion mode reducing repeated boilerplate,
- use devm_iio_triggered_buffer_setup to simplify error and remove
paths,
- use iio_device_claim_direct_mode instead of opencoding the same.
* ak8974
- mark the INT_CLEAR register as precious to prevent debugfs access.
* apds9300
- constify the i2c_device_id.
* at91-sama5 adc
- add missing Kconfig dependency.
* bma180 accel
- constify the i2c_device_id.
* rockchip_saradc
- explicitly request exclusive reset control as part of the reset rework
on going throughout the kernel.
* st_accel
- fix drdy configuration for a load of accelerometers that only have
the int1 line. Fix is unimportant as presumably no deviec tree actually
used the non existent hardware line.
* st_pressure
- fix drdy configuration for LPS22HB and LPS25H by dropping int2 support
as they don't have this. Fix is unimportant as presumably no device tree
actually used the non existent hardware line.
* stm32-dac
- explicitly request exclusive reset control (part of reset being reworked).
* tsl2583
- constify the i2c_device_id.
* xadc
- coding style fixes.
|
|
|
Greg Kroah-Hartman
|
8652892ed4 |
Merge 4.13-rc5 into staging-next
We need it here for iio fixes. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
|
|
Lorenzo Bianconi
|
ef0bc2e839 |
iio: pressure: st_pressure: fix drdy configuration for LPS22HB and LPS25H
Remove int2 configuration parameter for LPS22HB and LPS25H since these devices export just int1 as data-ready line Fixes: |
|
|
Andreas Klinger
|
eb92b4183d |
iio: bmp280: properly initialize device for humidity reading
If the device is not initialized at least once it happens that the humidity reading is skipped, which means the special value 0x8000 is delivered. For omitting this case the oversampling of the humidity must be set before the oversampling of the temperature und pressure is set as written in the datasheet of the BME280. Furthermore proper error detection is added in case a skipped value is read from the device. This is done also for pressure and temperature reading. Especially it don't make sense to compensate this value and treat it as regular value. Signed-off-by: Andreas Klinger <ak@it-klinger.de> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> |
|
|
Greg Kroah-Hartman
|
055655a9f0 |
First set of IIO fixes for the 4.13 cycle.
* ad2s1210 - Fix negative angular velocity reads (identified by a gcc 7 warning) * aspeed-adc - Wait for initialization sequence to finish before enabling channels. Without it no channels work. * axp288 - Revert a patch that dropped some bogus register mods. No one is entirely sure why but it breaks charging on some devices. - Fix GPADC pin read returning 0. Turns out a small sleep is needed. * bmc150 - Make sure device is restored to normal state after suspend / resume cycle. Otherwise, simple sysfs reads are broken. * tsl2563 - fix wrong event code. * st-accel - add spi 3-wire support. Needed to fix the lsm303agr accelerometer which only had 3 wires in all cases. Side effect is to enable optional 3-wire support for other devices. * st-pressure - disable multiread by default for LPS22HB (only effects SPI) * sun4i-gpadc-iio - fix unbalanced irq enable / disable * vf610 - Fix VALT slection for REFSEL bits - ensures we are using the right reference pins. -----BEGIN PGP SIGNATURE----- iQJFBAABCAAvFiEEbilms4eEBlKRJoGxVIU0mcT0FogFAll0lYgRHGppYzIzQGtl cm5lbC5vcmcACgkQVIU0mcT0FoipzRAAk7wO9hvfl8UwgS6FTLVwQQHjP6MQSZ51 USP2YN0hkBgDLKPQ2PbTt6t5jwboYPhOsd1n6iHWuAkje+W6Ie4JlXJBux/Gp9Wb GuZLLdFG+3Z1ZYcdDWRKs3u95vdku/5hFg63bxloPcpwkLzb82ykyQ4i9BjbGfv8 jrig+l3eghkGp1kl1ChGdeegTcHAVIS/lPm8Ls0BwpWM30tW2Ip4XSkkm+T6IHvT 8gPr1JMEJ5WaKEpDWKmitZQAr8jLAZ0dp9iLGh9qa2o0+OtX8gMYIas0bMHRR+UG 3EM0wWaaeSaOuqYs8ZnqUQE2RcqP6plZWRmLR98rFLrAXPATX/HGMtZ+JQpKwEKm 1H3XZAovwcppJ8X+XI7z6dZnpTCmQwwILYBpWvM/WWQCk2HZLZkFPOlkQyWCI4al 3OhV+6o3XIl/M8aHepcRh3tpwYFDToNhLpo85EC6H7YtwaReY8tfXqNtlO8MMIKm 1ZNVcA6NT8sdFwvyGtqg4yRIcQbx4Uarp11GgW5SSq13EgJ1LHEYC3lFrfn36pes D0oa01pA8hT6e7dPgqmFg6+J2XdWn8R1NVLRn+z+hjimr/BJlsxaZtk1JEJyS/ul qJS8UIEiwELUuze31uuz4QJJQHnPxuHlvM8EIf2c6vxg+l1CeMthXv7Hc9ht1vKg W/xgABUp/EY= =BApO -----END PGP SIGNATURE----- Merge tag 'iio-fixes-for-4.13a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus Jonathan writes: First set of IIO fixes for the 4.13 cycle. * ad2s1210 - Fix negative angular velocity reads (identified by a gcc 7 warning) * aspeed-adc - Wait for initialization sequence to finish before enabling channels. Without it no channels work. * axp288 - Revert a patch that dropped some bogus register mods. No one is entirely sure why but it breaks charging on some devices. - Fix GPADC pin read returning 0. Turns out a small sleep is needed. * bmc150 - Make sure device is restored to normal state after suspend / resume cycle. Otherwise, simple sysfs reads are broken. * tsl2563 - fix wrong event code. * st-accel - add spi 3-wire support. Needed to fix the lsm303agr accelerometer which only had 3 wires in all cases. Side effect is to enable optional 3-wire support for other devices. * st-pressure - disable multiread by default for LPS22HB (only effects SPI) * sun4i-gpadc-iio - fix unbalanced irq enable / disable * vf610 - Fix VALT slection for REFSEL bits - ensures we are using the right reference pins. |
|
|
Joe Perches
|
eed3089fb2 |
iio: pressure: zpa2326: Add newlines to logging macros
Add newlines to the macro definitions and use a more common style. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> |
|
|
Lorenzo Bianconi
|
2ff59bf39b |
iio: pressure: st_pressure_spi: add OF capability to st_pressure_spi
Add device tree support for LPS22HB, LPS25H, LPS331AP, LPS001WP pressure sensors Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org> |
|
|
Manivannan Sadhasivam
|
1813c71317 |
iio: pressure: ms5637: Add OF match table
Add of_match_table for Measurement-Specialties MS5637, MS5805, MS5837 and MS8607 pressure & temperature sensor Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org> |
|
|
Lorenzo Bianconi
|
250bbbdbed |
iio: common: st_sensors: move st_sensors_of_i2c_probe() in common code
Move st_sensors_of_i2c_probe() in st_sensors_core and rename it in st_sensors_of_name_probe(). That change is necessary to add device-tree support in spi code otherwise the rest of the autodetection will fail since spi->modalias (and indio_dev->name) will be set using compatible string value that differs from standard sensor name Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> |
|
|
Lorenzo Bianconi
|
add6e6ab3e |
iio: pressure: st_pressure_core: disable multiread by default for LPS22HB
Set multiread variable to false for LPS22HB pressure sensor since
it is already enabled in CTRL_REG2. Previous configuration does not
cause any issue in I2C communication since SUB Msb has no meaning
whereas it breaks register address in SPI communication
Fixes:
|
|
|
Nicholas Mc Guire
|
e7215fe4d5 |
iio: pressure: zpa2326: report interrupted case as failure
If the timeout-case prints a warning message then probably the interrupted
case should also. Further, wait_for_completion_interruptible_timeout()
returns long not int.
Fixes: commit
|
|
|
Shrirang Bagul
|
7383d44b84 |
iio: st_pressure: st_accel: Initialise sensor platform data properly
This patch fixes the sensor platform data initialisation for st_pressure and st_accel device drivers. Without this patch, the driver fails to register the sensors when the user removes and re-loads the driver. 1. Unload the kernel modules for st_pressure $ sudo rmmod st_pressure_i2c $ sudo rmmod st_pressure 2. Re-load the driver $ sudo insmod st_pressure $ sudo insmod st_pressure_i2c Signed-off-by: Jonathan Cameron <jic23@kernel.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> |
|
|
Peter Meerwald-Stadler
|
9a043b0bf2 |
iio: pressure: Fix name of BME280 part in Kconfig
Bosch BME280 is a combined pressure and humidity sensor Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Signed-off-by: Jonathan Cameron <jic23@kernel.org> |
|
|
Greg Kroah-Hartman
|
df47c0a638 |
Fifth set of IIO fixes for the 4.11 cycle.
As these are rather late in the cycle, they may sneak over into 4.12. There is a fix for a regression caused by another fix (hid sensors hardware seems to vary a lot in how various corner cases are handled). * ad7303 - fix channel description. Numeric values were being passed as characters presumably leading to garbage from the userspace interface. * as3935 - the write data macro was wrong so fix it. * bmp280 - incorrect handling of negative values as being unsigned broke humidity calculation. * hid-sensor - Restore the poll and hysteresis values after resume as some hardware doesn't do it. * stm32-trigger - buglet in reading the sampling frequency -----BEGIN PGP SIGNATURE----- iQJFBAABCAAvFiEEbilms4eEBlKRJoGxVIU0mcT0FogFAljw8ScRHGppYzIzQGtl cm5lbC5vcmcACgkQVIU0mcT0FojZvBAAh8K9e+3ObpS6/0wj26/XsakiFn4v2ah0 xKUnafxAVVxU3AU01IJ3CtNdIMyqMwpnB+PvnpgDzZw749QrYKPsBIzheK64eabe fzA34X5MWGLwUdOXpfEB0xvsylWjJrqsf1rahgZjiUKkPeZe9EwzPM/fP1sEl5gu p+vfSMckboFaKheoQwnWMUTBp0HK+nbFpcSBzljX68u+epiXpDGrjuZC8NJ3JuBn Bloz9AhDliIn477H7mIUTXBbt3ixLIDiJ7haQuTNlagosPoUtCBpwY2O9mZ7VRVs wM62h7/F170077ReQJRjlfck+7uHoIgDeS46w5UYTzA1HJLxs+veO5xv3VOtHIUg BZ+mibQyIUBrFeyYDVbeUpBTffiU6rA+yiM4WFwUFabl7t7rlG0NhLEx7OIQcFMm l8u/5JUoJcoykaO8c9Jx5XtrgkXq+rCWVAmhjHqUDAlvsMa6pJWEyqgaVcQeIbdw ns9ppJRlOmEst7lMab9TI7BJp3oCIH6uRmctbme42Rw8XgDFdltxqkxmjB8d+cDC Q0INhNJN1jRgz6rT6lkxVhAYKtaP5T8qZeliT4MO1E59ggOVSSf8zuhjrEMUK397 Tu/k7fmATtiKSG+blwYZVRC3+ixh/oKZsvfwZ4O+mFJyhQ616nKMYAywoaZcM8WT Z1ABipUDwsE= =H5KS -----END PGP SIGNATURE----- Merge tag 'iio-fixes-for-4.11e' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next Jonathan writes: Fifth set of IIO fixes for the 4.11 cycle. As these are rather late in the cycle, they may sneak over into 4.12. There is a fix for a regression caused by another fix (hid sensors hardware seems to vary a lot in how various corner cases are handled). * ad7303 - fix channel description. Numeric values were being passed as characters presumably leading to garbage from the userspace interface. * as3935 - the write data macro was wrong so fix it. * bmp280 - incorrect handling of negative values as being unsigned broke humidity calculation. * hid-sensor - Restore the poll and hysteresis values after resume as some hardware doesn't do it. * stm32-trigger - buglet in reading the sampling frequency |
|
|
Andreas Klinger
|
ed3730c435 |
IIO: bmp280-core.c: fix error in humidity calculation
While calculating the compensation of the humidity there are negative values interpreted as unsigned because of unsigned variables used. These values as well as the constants need to be casted to signed as indicated by the documentation of the sensor. Signed-off-by: Andreas Klinger <ak@it-klinger.de> Acked-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Matt Ranostay <matt.ranostay@konsulko.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org> |
|
|
Greg Kroah-Hartman
|
f78a8236c6 |
Merge 4.11-rc6 into staging-next
We want the staging and iio fixes in here to handle merging easier. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
|
|
Shrirang Bagul
|
51f528a163 |
iio: st_pressure: initialize lps22hb bootime
This patch initializes the bootime in struct st_sensor_settings for lps22hb sensor. Without this, sensor channels read from sysfs always report stale values. Signed-off-by: Shrirang Bagul <shrirang.bagul@canonical.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org> |
|
|
simran singhal
|
af873b0d8f |
iio: pressure: zpa2326: Remove unnecessary cast on void pointer
The following Coccinelle script was used to detect this: @r@ expression x; void* e; type T; identifier f; @@ ( *((T *)e) | ((T *)x)[...] | ((T*)x)->f | - (T*) e ) Signed-off-by: simran singhal <singhalsimran0@gmail.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> |
|
|
Javier Martinez Canillas
|
77496c078c |
iio: pressure: mpl3115: Add OF device ID table
The driver doesn't have a struct of_device_id table but supported devices are registered via Device Trees. This is working on the assumption that a I2C device registered via OF will always match a legacy I2C device ID and that the MODALIAS reported will always be of the form i2c:<device>. But this could change in the future so the correct approach is to have an OF device ID table if the devices are registered via OF. Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> |
|
|
Javier Martinez Canillas
|
72fc0270a9 |
iio: pressure: hp03: Add OF device ID table
The driver doesn't have a struct of_device_id table but supported devices are registered via Device Trees. This is working on the assumption that a I2C device registered via OF will always match a legacy I2C device ID and that the MODALIAS reported will always be of the form i2c:<device>. But this could change in the future so the correct approach is to have an OF device ID table if the devices are registered via OF. Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> |
|
|
Greg Kroah-Hartman
|
b96dea60bc |
First set of IIO fixes for the 4.11 cycle. Regression fixes from 4.10.
These are fixes that came in just to late for the 4.10 cycle. Two drivers made an accidental assumption of structure arrangement for struct iio_dev that are no longer true. It was a typo in the first place that happened to work until some elements were added to the structure. * mpl3115 - don't rely on structure field ordering * mpl115 - don't rely on structure field ordering. -----BEGIN PGP SIGNATURE----- iQJFBAABCAAvFiEEbilms4eEBlKRJoGxVIU0mcT0FogFAlie07IRHGppYzIzQGtl cm5lbC5vcmcACgkQVIU0mcT0Fohcpg//XXnNnUq4K90bM7krxcM0+0iQze5ZJOUJ BqXV8IfFicbeeo0a463g0wcYAJ1kmzNJV3eqMhCUC7seYoqQ6ji1FCPN0qw/TSv1 Mc9pE15i3GJ3vjsWKWMr0Bc0Gg+Ccah0aO/P3eatuwtvakZfPeUpvZakWBdkr1mP 97OlBm0BdOBF8tXJ9KAEe3rB/pJDLc2JNpIIlRi8hitw+GRpnhdZzLpwbZKG6Ytf ozT3IUC7LpnolCfpnzvCkSpHZnAr22MVPXkHLK7a4Vb/C3mTjJVsKjTdXN60luh3 C0hcN3IWyb/KAwLPSK9dqbkQBvoDSOtG8EGBeZoXdc1lHtia90Qp3hTeINDwRvPl un37OUYdEOtZ4JPG7FGHvgdc8bhkUJv2ZHITZWaIdZJAVj8DOWfQcydtxjHP/t8k mtgcg+OMCkgihN97kLqYS1dJnZIy3PwxoooDOJ0KB8/S8N3SbaWOFfuGWYaQikVL IIRA7CyWI3yEjioqfWc/ujXUgjhFNc7XC9M44huEg+ysExW5OamsoVtbEoqCOVIm s7NwoyRbjaDHzaLiulX/eCzb1C02PV0wof3NrPMv4T3Ao4L4cG34Pe5zOcKAPWr4 WefoZATobg6AmMEuK4CYtP3l0mInVw7vSGPfW9+D+3PppA8QRLCWgFbO0CENnMVM K4oBg9E7Sd0= =DW22 -----END PGP SIGNATURE----- Merge tag 'iio-fixes-for-4.11a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next Jonathan writes: First set of IIO fixes for the 4.11 cycle. Regression fixes from 4.10. These are fixes that came in just to late for the 4.10 cycle. Two drivers made an accidental assumption of structure arrangement for struct iio_dev that are no longer true. It was a typo in the first place that happened to work until some elements were added to the structure. * mpl3115 - don't rely on structure field ordering * mpl115 - don't rely on structure field ordering. |
|
|
Peter Rosin
|
6a6e1d56a0 |
iio: pressure: mpl115: do not rely on structure field ordering
Fixes a regression triggered by a change in the layout of struct iio_chan_spec, but the real bug is in the driver which assumed a specific structure layout in the first place. Hint: the three bits were not OR:ed together as implied by the indentation prior to this patch, there was a comma between the first two, which accidentally moved the ..._SCALE and ..._OFFSET bits to the next structure field. That field was .info_mask_shared_by_type before the _available attributes was added by commit |
|
|
Peter Rosin
|
9cf6cdba58 |
iio: pressure: mpl3115: do not rely on structure field ordering
Fixes a regression triggered by a change in the layout of struct iio_chan_spec, but the real bug is in the driver which assumed a specific structure layout in the first place. Hint: the two bits were not OR:ed together as implied by the indentation prior to this patch, there was a comma between them, which accidentally moved the ..._SCALE bit to the next structure field. That field was .info_mask_shared_by_type before the _available attributes was added by commit |
|
|
Gwendal Grignou
|
d732248fdb |
iio: cros_ec: Add cros_ec barometer driver
Handle the barometer sensor presented by the ChromeOS EC Sensor hub. Signed-off-by: Gwendal Grignou <gwendal@chromium.org> Signed-off-by: Enric Balletbo Serra <enric.balletbo@collabora.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> |
|
|
Alison Schofield
|
3bc1abcddb |
iio: pressure: ms5611: claim direct mode during oversampling changes
Driver was checking for direct mode before changing oversampling ratios, but was not locking it. Use the claim/release helper functions to guarantee the device stays in direct mode while the oversampling ratios are being updated. Continue to use the drivers private state lock to protect against conflicting direct mode access of the state data. Signed-off-by: Alison Schofield <amsfield22@gmail.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> |
|
|
Marcin Niestroj
|
7f0d874036 |
iio: st_pressure: Export sampling frequency for lps25h and lps331ap
Both devices are using the same iio_chan_spec to define which settings are exported with sysfs. Both are properly configured to set/get sampling frequency for pressure and temperature. They also properly export available sampling frequencies. The only missing thing is sampling_frequency sysfs file, which allows to set/get this property from userspace. Add sampling frequency to iio channel info mask, so sampling_frequency file is properly exported using sysfs. Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org> |
|
|
Marcin Niestroj
|
1b211d48ab |
iio: st_pressure: Fix data sign
Datasheet of each device (lps331ap, lps25h, lps001wp, lps22hb) says that the pressure and temperature data is a 2's complement. I'm sending this the slow way, as negative pressures on these are pretty unusual and the nature of the fixing of multiple device introduction patches will make it hard to apply to older kernels - Jonathan. Fixes: |
|
|
Aniroop Mathur
|
071cf24943 |
IIO: Change msleep to usleep_range for small msecs
msleep(1~20) may not do what the caller intends, and will often sleep longer. (~20 ms actual sleep for any value given in the 1~20ms range) This is not the desired behaviour for many cases like device resume time, device suspend time, device enable time, data reading time, etc. Thus, change msleep to usleep_range for precise wakeups. Signed-off-by: Aniroop Mathur <a.mathur@samsung.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> |
|
|
Shrirang Bagul
|
9d317724cf |
iio: st_pressure: Support i2c probe using acpi
Compatible strings are not available on ACPI based systems. This patch adds support to use DSDT information read from platform BIOS instead for probing st pressure sensors. Signed-off-by: Shrirang Bagul <shrirang.bagul@canonical.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> |
|
|
Linus Walleij
|
91a86a3b89 |
iio: pressure: st_pressure: inline per-sensor data
We have #defines for all the individual sensor registers and value/mask pairs #defined at the top of the file and used at exactly one spot. This is usually good if the #defines give a meaning to the opaque magic numbers. However in this case, the semantic meaning is inherent in the name of the C99-addressable fields, and that means duplication of information, and only makes the code hard to maintain since you every time have to add a new #define AND update the site where it is to be used. Get rid of the #defines and just open code the values into the appropriate struct elements. Make sure to explicitly address the .hz and .value fields in the st_sensor_odr_avl struct so that the meaning of all values is clear. This patch is purely syntactic should have no semantic effect. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org> |
|
|
Greg Kroah-Hartman
|
c7c88e998a |
First round of IIO new device support, features and cleanups for the 4.10 cycle.
Fair number of outreachy related patches in here. Some of these may well
have already been picked up by Greg but git will sort that out for us.
Also some good staging cleanup work from other sources. Thanks Brian and Lars
in particular for this.
New device support
* ACCES 104-quad-8
- New driver for this 8 channel encoder input board. Lots of new ABI with
this one.
* AD7766
- New driver supporting AD7766, AD7766-1, AD7766-2, AD7767, AD7767-1 and
AD7767-2 24 bit ADCs.
* dmard 10
- New driver for this 3 axis accelerometer.
* Honeywell ABP pressure sensors.
- New driver covering 56 parts in this series (too many to list here!)
* HTS221
- New driver to support this relative humidiy and temperature device.
* LMP91000
- New driver for this potentiostat (form of chemical sensor). Nice example
of use of the buffered consumer interfaces and the use of a consumer
provided trigger.
* MiraMEMS DA311
- New driver for this 3 axis accelerometer.
* MiraMEMS DA280
- New driver for this 3 axis accelerometer. Follow up caught up with
vendor prefixes for these.
Staging graduations
* isl29018 light sensor
- Fixes and cleanups listed below (thanks for your hard work on this Brian!)
* sca3000
- Fixes and cleanups listed below. This was one of the small set of drivers
that went into staging when IIO was first added. Turns out it had a few
bugs and needed to be brought into the modern era! Not clear if I am
the only person who actually has one of these still wired to a board.
New features (Core)
- Add an iio_trigger_validate_own_device helper which relies on the device
and trigger having the same parent. Convenient to have this for some
of the more complex trigger / device interactions. Was hand rolled in
a few drivers already so good to bring it into the core.
- Add an iio_read_channel_offset in kernel access helper (similar to
the existing one for scale).
- IIO_ATTR_{RO, WO, RW} and IIO_DEVICE_ATTR_{RO, WO, RW} macros. These
lead some rather contrived function naming, but there is no denying they
do reduced boilerplate. I'm going to resist their introduction in
drivers 'unless' they form part of a larger set of cleanups.
- Counter channel type and index type.
New features (Drivers)
* hdc100x
- Triggered buffer support.
* mcp4725
- Device tree bindings and support.
- Voltage reference selection.
* ti-adc0832
- Triggered buffer support.
* ti-adc161s626
- Add regulator support allowing _scale and _offset values to be established
and exported.
New features (Tools)
* iio_generic_buffer
- -A option to force enable all channels rather than faulting if some are
already enabled (like -a does). Followup patches tidied this support up.
Cleanups (Core)
- Use kmalloc_array in iio_scan_mask_set.
- Take event_attrs field of iio_info structure constant
- Staging todo list updates. Most of it was long done.
- MAINTAINERS had a wrong directory listing.
Cleanups (Drivers)
* Missing i2c trivial devices entries.
* ad5592r
- Fix an endian type related sparse warnings.
* ad7150
- Constify the event attribute_group structures.
* ad7152
- Add some blank lines to improve readability.
- Sampling frequency control via chan-info element rather than hand rolled
attributes.
- add a new lock to avoid use of mlock for non state change related locking.
* ad7280
- Constify atrribute_group structure (second patch covers the event ones)
* ad7606 (Lars is driving most of the cleanup on this with some additions from
Eva)
- Fix improper setting of oversampling pins. This has been broken a very
long time in this staging driver, so not going to push this back to stable.
- Implement oversampling configuration via the chan_info mask element.
- Remove an unused int_vref_mv field.
- Remove a reundant name field from ad7606_chip_info.
- Remove default device configuration from platform_data in favour of
whatever the power on defaults are.
- Remove out of band error reporting in the kernel log as not providing
much information.
- Fix oversampling ratio by having 1 be the value for no oversampling.
- Avoid allocating buffer for each data capture.
- Factor out common code between periodic and one-shot capture.
- Move set_drvdat into common code.
- Let the common probe function return int rather than jumping through
an ERR_PTR.
- Pass struct device * into common remove to simplify code.
- Always run trigger handler only once per event (no one can remember why
it was being possibly done twice).
- Move over to the GPIO descriptor API to shorten and clarify code.
- Move the buffer code into the main file as it's not optional and is
now rather short in this driver.
- Fix the naming of the supply regulator.
- Rework regulator handling to handle errors including deferred probing.
- Tidy up a ptr_err or 0 return.
* ad7746
- Sampling frequency control via info_mask element rather than hand rolled
* ad7758
- Sampling frequency control via info_mask element rather than hand rolled
attributes.
* ad7816
- Constify the event attribute_group structure.
* adt7316
- Constify the event attribute group structures.
* ak8974
- Cleanup some sparse warnings about endian types.
* ak8975
- Cleanup some sparse warnings about endian types.
* bmi160
- Spare endian warning cleanups.
* isl29018 (towards staging graduation)
- Remove unusedvariables and defines.
- Improve consistency of error handling.
- Signed / unsigned comparison fixes.
- Use the IIO_DEVICE_ATTR_{RO, RW} macros
- Fix a race in in_illuminance_scale_available_show.
- Cleanup exit points of _read_raw
- Sanity check if in suspended state during a write_raw call as was already
done for read_raw.
- Document device tree bidnings.
- Document infrared supression controls.
- Add some newlines to improve readability and drop one that shouldn't be
there.
- Fix a poorly named functions name.
- Fix multiline coment syntax.
- Tidy up a pair or return statements by unifying them.
- Rename description in Kconfig for consistency with similar drivers.
* lidar
- cleanup power management by dropping unnecessary call.
* ltr501
- Use the claim_direct_mode helpers. Fix a race condition along the way.
* max1027
- Fix a dubious x | !y sparse warning.
- Use the new iio_trigger_validate_own_device helper.
* max440000
- Clean up some sparse warnings about endian types.
* mcp4725
- Use the regulator framework to establish the reference voltage rather than
getting it from platform data.
- Tidy up a comment typo.
- Fix a wrong PTR_ERR query (wrong regulator).
* mma7660
- Take a mma7660_nscale static.
* mma8452
- Use the new iio_trigger_validate_own_device helper.
- Use claim_direct_mode helpers - fix a race condition along the way.
* mpl3115
- Use claim_direct_mode helpers - fix a race condition along the way.
* ms65611
- Tidy up regulator error handling and clean out a static warning in the mix.
* sca3000
- Avoid a potential unitialized variable if a hardware read returns a value
that isn't actually supported (mostly warning supression).
- Fix a use before setting of the indio_dev->buffer pointer. Broken for
a very long time so not going to rush this into stable.
- Merge buffer file with core file. We used to always split these.
Sometimes it's just not worth the hassle. In this case the device's main
feature is it's hardware fifos so unlikely anyone would want to run it
without.
- Drop the sca3000_register_ring_funcs function as it's a pointless wrapper
once we have only one file.
- Fix cleaning of flag + setting of size of scan. Without this you can't
start the buffer twice and expect sensible (or any) results. Again,
broken for a long time so not heading for stable.
- Drop the custom watershed setting ABI - for now we'll just support one
value.
- Move to a hybrid hard / soft buffer design (how we've been doing it
for similar devices for a while now!)
- Cleanup some unusued variables.
- Use a fake channel to support core handling of freefall event registration.
- Cleanup the register defines.
- Fix an off by one error in axis due to IIO_NO_MOD taking up the 0 value.
Been broken since first admission of IIO to the staging tree.
- Add readback of the 3db low pass filter frequency and later writing
allowing droppign of custom measurement mode attributes as they can
be represented by the filter choices that is their main characteristic.
- Drop non standard revision attr and replace with dev_info on probe.
- Avoid a race in probe.
- Various formatting fixes.
- Kernel-docify docs that were very nearly in the write format.
* tsl2583
- Constify attribute_group structure.
* zpa2326
- Drop a redundant DEBUG ifdef.
Cleanups (Tools)
* iio_generic_buffer
- Fix the ? arguement. Previously it sort of worked as you got the help
message as a result of it not recognising the arguement.
-----BEGIN PGP SIGNATURE-----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=ZRUt
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.10a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of IIO new device support, features and cleanups for the 4.10 cycle.
Fair number of outreachy related patches in here. Some of these may well
have already been picked up by Greg but git will sort that out for us.
Also some good staging cleanup work from other sources. Thanks Brian and Lars
in particular for this.
New device support
* ACCES 104-quad-8
- New driver for this 8 channel encoder input board. Lots of new ABI with
this one.
* AD7766
- New driver supporting AD7766, AD7766-1, AD7766-2, AD7767, AD7767-1 and
AD7767-2 24 bit ADCs.
* dmard 10
- New driver for this 3 axis accelerometer.
* Honeywell ABP pressure sensors.
- New driver covering 56 parts in this series (too many to list here!)
* HTS221
- New driver to support this relative humidiy and temperature device.
* LMP91000
- New driver for this potentiostat (form of chemical sensor). Nice example
of use of the buffered consumer interfaces and the use of a consumer
provided trigger.
* MiraMEMS DA311
- New driver for this 3 axis accelerometer.
* MiraMEMS DA280
- New driver for this 3 axis accelerometer. Follow up caught up with
vendor prefixes for these.
Staging graduations
* isl29018 light sensor
- Fixes and cleanups listed below (thanks for your hard work on this Brian!)
* sca3000
- Fixes and cleanups listed below. This was one of the small set of drivers
that went into staging when IIO was first added. Turns out it had a few
bugs and needed to be brought into the modern era! Not clear if I am
the only person who actually has one of these still wired to a board.
New features (Core)
- Add an iio_trigger_validate_own_device helper which relies on the device
and trigger having the same parent. Convenient to have this for some
of the more complex trigger / device interactions. Was hand rolled in
a few drivers already so good to bring it into the core.
- Add an iio_read_channel_offset in kernel access helper (similar to
the existing one for scale).
- IIO_ATTR_{RO, WO, RW} and IIO_DEVICE_ATTR_{RO, WO, RW} macros. These
lead some rather contrived function naming, but there is no denying they
do reduced boilerplate. I'm going to resist their introduction in
drivers 'unless' they form part of a larger set of cleanups.
- Counter channel type and index type.
New features (Drivers)
* hdc100x
- Triggered buffer support.
* mcp4725
- Device tree bindings and support.
- Voltage reference selection.
* ti-adc0832
- Triggered buffer support.
* ti-adc161s626
- Add regulator support allowing _scale and _offset values to be established
and exported.
New features (Tools)
* iio_generic_buffer
- -A option to force enable all channels rather than faulting if some are
already enabled (like -a does). Followup patches tidied this support up.
Cleanups (Core)
- Use kmalloc_array in iio_scan_mask_set.
- Take event_attrs field of iio_info structure constant
- Staging todo list updates. Most of it was long done.
- MAINTAINERS had a wrong directory listing.
Cleanups (Drivers)
* Missing i2c trivial devices entries.
* ad5592r
- Fix an endian type related sparse warnings.
* ad7150
- Constify the event attribute_group structures.
* ad7152
- Add some blank lines to improve readability.
- Sampling frequency control via chan-info element rather than hand rolled
attributes.
- add a new lock to avoid use of mlock for non state change related locking.
* ad7280
- Constify atrribute_group structure (second patch covers the event ones)
* ad7606 (Lars is driving most of the cleanup on this with some additions from
Eva)
- Fix improper setting of oversampling pins. This has been broken a very
long time in this staging driver, so not going to push this back to stable.
- Implement oversampling configuration via the chan_info mask element.
- Remove an unused int_vref_mv field.
- Remove a reundant name field from ad7606_chip_info.
- Remove default device configuration from platform_data in favour of
whatever the power on defaults are.
- Remove out of band error reporting in the kernel log as not providing
much information.
- Fix oversampling ratio by having 1 be the value for no oversampling.
- Avoid allocating buffer for each data capture.
- Factor out common code between periodic and one-shot capture.
- Move set_drvdat into common code.
- Let the common probe function return int rather than jumping through
an ERR_PTR.
- Pass struct device * into common remove to simplify code.
- Always run trigger handler only once per event (no one can remember why
it was being possibly done twice).
- Move over to the GPIO descriptor API to shorten and clarify code.
- Move the buffer code into the main file as it's not optional and is
now rather short in this driver.
- Fix the naming of the supply regulator.
- Rework regulator handling to handle errors including deferred probing.
- Tidy up a ptr_err or 0 return.
* ad7746
- Sampling frequency control via info_mask element rather than hand rolled
* ad7758
- Sampling frequency control via info_mask element rather than hand rolled
attributes.
* ad7816
- Constify the event attribute_group structure.
* adt7316
- Constify the event attribute group structures.
* ak8974
- Cleanup some sparse warnings about endian types.
* ak8975
- Cleanup some sparse warnings about endian types.
* bmi160
- Spare endian warning cleanups.
* isl29018 (towards staging graduation)
- Remove unusedvariables and defines.
- Improve consistency of error handling.
- Signed / unsigned comparison fixes.
- Use the IIO_DEVICE_ATTR_{RO, RW} macros
- Fix a race in in_illuminance_scale_available_show.
- Cleanup exit points of _read_raw
- Sanity check if in suspended state during a write_raw call as was already
done for read_raw.
- Document device tree bidnings.
- Document infrared supression controls.
- Add some newlines to improve readability and drop one that shouldn't be
there.
- Fix a poorly named functions name.
- Fix multiline coment syntax.
- Tidy up a pair or return statements by unifying them.
- Rename description in Kconfig for consistency with similar drivers.
* lidar
- cleanup power management by dropping unnecessary call.
* ltr501
- Use the claim_direct_mode helpers. Fix a race condition along the way.
* max1027
- Fix a dubious x | !y sparse warning.
- Use the new iio_trigger_validate_own_device helper.
* max440000
- Clean up some sparse warnings about endian types.
* mcp4725
- Use the regulator framework to establish the reference voltage rather than
getting it from platform data.
- Tidy up a comment typo.
- Fix a wrong PTR_ERR query (wrong regulator).
* mma7660
- Take a mma7660_nscale static.
* mma8452
- Use the new iio_trigger_validate_own_device helper.
- Use claim_direct_mode helpers - fix a race condition along the way.
* mpl3115
- Use claim_direct_mode helpers - fix a race condition along the way.
* ms65611
- Tidy up regulator error handling and clean out a static warning in the mix.
* sca3000
- Avoid a potential unitialized variable if a hardware read returns a value
that isn't actually supported (mostly warning supression).
- Fix a use before setting of the indio_dev->buffer pointer. Broken for
a very long time so not going to rush this into stable.
- Merge buffer file with core file. We used to always split these.
Sometimes it's just not worth the hassle. In this case the device's main
feature is it's hardware fifos so unlikely anyone would want to run it
without.
- Drop the sca3000_register_ring_funcs function as it's a pointless wrapper
once we have only one file.
- Fix cleaning of flag + setting of size of scan. Without this you can't
start the buffer twice and expect sensible (or any) results. Again,
broken for a long time so not heading for stable.
- Drop the custom watershed setting ABI - for now we'll just support one
value.
- Move to a hybrid hard / soft buffer design (how we've been doing it
for similar devices for a while now!)
- Cleanup some unusued variables.
- Use a fake channel to support core handling of freefall event registration.
- Cleanup the register defines.
- Fix an off by one error in axis due to IIO_NO_MOD taking up the 0 value.
Been broken since first admission of IIO to the staging tree.
- Add readback of the 3db low pass filter frequency and later writing
allowing droppign of custom measurement mode attributes as they can
be represented by the filter choices that is their main characteristic.
- Drop non standard revision attr and replace with dev_info on probe.
- Avoid a race in probe.
- Various formatting fixes.
- Kernel-docify docs that were very nearly in the write format.
* tsl2583
- Constify attribute_group structure.
* zpa2326
- Drop a redundant DEBUG ifdef.
Cleanups (Tools)
* iio_generic_buffer
- Fix the ? arguement. Previously it sort of worked as you got the help
message as a result of it not recognising the arguement.
|
|
|
Alison Schofield
|
ac13980584 |
iio: pressure: mpl3115: claim direct mode during raw reads
Driver was checking for direct mode but not locking it. Use claim/release helper functions to guarantee the device stays in direct mode during raw reads. Signed-off-by: Alison Schofield <amsfield22@gmail.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> |
|
|
Crt Mori
|
3f5def652f |
iio: ms65611_core: Fixes dereferencing regulator pointer
Change in handling of the regulator description means that static checkers correctly assume we could be using dereferenced pointer to the regulator. In reality we will never get the -ENODEV error, as current behavior flow does not predict it, because: If the device tree or board file does not define suitable regulators for the component, it will be substituted by a dummy regulator, or, if regulators are disabled altogether, by stubs. Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Suggested-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Crt Mori <cmo@melexis.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> |
|
|
Linus Torvalds
|
41844e3620 |
Staging/IIO patches for 4.9-rc1
Here is the big staging and IIO driver pull request for 4.9-rc1. There are a lot of patches in here, the majority due to the drivers/staging/greybus/ subsystem being merged in with full development history that went back a few years, in order to preserve the work that those developers did over time. This was done the same way that btrfs was merged into the tree, so all should be ok there. Lots and lots of tiny cleanups happened in the tree as well, due to the Outreachy application process and lots of other developers showing up for the first time to clean code up. Along with those changes, we deleted a wireless driver, and added a raspberrypi driver (currently marked broken), and lots of new iio drivers. Overall the tree still shrunk with more lines removed than added, about 10 thousand lines removed in total. Full details are in the very long shortlog below. All of this has been in the linux-next tree with no issues. There will be some merge problems with other subsystem trees, but those are all minor problems and shouldn't be hard to work out when they happen (MAINTAINERS and some lustre build problems with the IB tree.) Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> -----BEGIN PGP SIGNATURE----- iFYEABECABYFAlf0qWIPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfsp9GkAoLMa Dl/S8W02azDtKP893es5GXh3AJ4k8J9JlHgTS0RlzVJMvzkSZ2x7Vg== =j18s -----END PGP SIGNATURE----- Merge tag 'staging-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging Pull staging and IIO updates from Greg KH: "Here is the big staging and IIO driver pull request for 4.9-rc1. There are a lot of patches in here, the majority due to the drivers/staging/greybus/ subsystem being merged in with full development history that went back a few years, in order to preserve the work that those developers did over time. Lots and lots of tiny cleanups happened in the tree as well, due to the Outreachy application process and lots of other developers showing up for the first time to clean code up. Along with those changes, we deleted a wireless driver, and added a raspberrypi driver (currently marked broken), and lots of new iio drivers. Overall the tree still shrunk with more lines removed than added, about 10 thousand lines removed in total. Full details are in the very long shortlog below. All of this has been in the linux-next tree with no issues. There will be some merge problems with other subsystem trees, but those are all minor problems and shouldn't be hard to work out when they happen (MAINTAINERS and some lustre build problems with the IB tree)" And furter from me asking for clarification about greybus: "Right now there is a phone from Motorola shipping with this code (a slightly older version, but the same tree), so even though Ara is not alive in the same form, the functionality is happening. We are working with the developers of that phone to merge the newer stuff in with their fork so they can use the upstream version in future versions of their phone product line. Toshiba has at least one chip shipping in their catalog that needs/uses this protocol over a Unipro link, and rumor has it that there might be more in the future. There are also other users of the greybus protocols, there is a talk next week at ELC that shows how it is being used across a network connection to control a device, and previous ELC talks have showed the protocol stack being used over USB to drive embedded Linux boards. I've also talked to some people who are starting to work to add a host controller driver to control arduinos as the greybus PHY protocols are very useful to control a serial/i2c/spio/whatever device across a random physical link, as it is a way to have a self-describing device be attached to a host without needing manual configuration. So yes, people are using it, and there is still the chance that it will show up in a phone/laptop/tablet/whatever from Google in the future as well, the tech isn't dead, even if the original large phone project happens to be" * tag 'staging-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (3703 commits) Staging: fbtft: Fix bug in fbtft-core staging: rtl8188eu: fix double unlock error in rtw_resume_process() staging:r8188eu: remove GEN_MLME_EXT_HANDLER macro staging:r8188eu: remove GEN_DRV_CMD_HANDLER macro staging:r8188eu: remove GEN_EVT_CODE macro staging:r8188eu: remove GEN_CMD_CODE macro staging:r8188eu: remove pkt_newalloc member of the recv_buf structure staging:r8188eu: remove rtw_handle_dualmac declaration staging:r8188eu: remove (RGTRY|BSSID)_(OFT|SZ) macros staging:r8188eu: change rtl8188e_process_phy_info function argument type Staging: fsl-mc: Remove blank lines Staging: fsl-mc: Fix unaligned * in block comments Staging: comedi: Align the * in block comments Staging : ks7010 : Fix block comments warninig Staging: vt6655: Remove explicit NULL comparison using Coccinelle staging: rtl8188eu: core: rtw_xmit: Use macros instead of constants staging: rtl8188eu: core: rtw_xmit: Move constant of the right side staging: dgnc: Fix lines longer than 80 characters Staging: dgnc: constify attribute_group structures Staging: most: hdm-dim2: constify attribute_group structures ... |
|
|
Marcin Malagowski
|
9ecca12edd |
iio: pressure: Add driver for Honeywell ABP family
This patch adds minimal driver for the Honeywell Amplified Basic Pressure sensors series. Sensors are pretty simple but are available in many variants: - psi/mbar/kPa output, - analog/i2c/spi, - gage/differential measurement, - different measure ranges etc. Refer to datasheets for more details: http://sensing.honeywell.com/honeywell-sensing-basic-board-mount-pressure-sensors-abp-series-datasheet-323005128-c-en.pdf http://sensing.honeywell.com/index.php%3Fci_id%3D45841 Driver internals: - i2c only. measure request is done by the SMBUS QUICK cmd, so if the i2c bus doesn't support it, it is required to send a dummy byte to trigger measurement, - since iio sysfs expects kilopascals, mbar-variants are treated as their respective kPa-s, hence i2c id-table has doubled entries in one line: { "abp060mg", ABP006KG }, { "abp006kg", ABP006KG }, - psi-variants have prescaled values in config, - no temperature reads yet. Work remained: - optional temperature channel, - SPI support, - DT binding. Changes since v1: - mutex is now locked in read_raw(), - corrected error codes, - fixed coding style issues, - renamed few defines and functions abp -> abp060mg (some structs left as they were to keep the sensible meaning). Signed-off-by: Marcin Malagowski <mrc@bourne.st> Signed-off-by: Jonathan Cameron <jic23@kernel.org> |
|
|
Arnd Bergmann
|
59dc1c8619 |
iio:pressure: zpa2326: remove redundant "DEBUG" ifdef
The -Wempty-body gcc warning triggers in the newly added zpa2326 driver:
drivers/iio/pressure/zpa2326.c: In function 'zpa2326_dequeue_pressure':
drivers/iio/pressure/zpa2326.c:578:3: error: suggest braces around empty body in an 'if' statement [-Werror=empty-body]
The use of an empty statement behind 'if (...)' is harmless here, but
it shows that the dev_dbg() macro is not used correctly: when the "DEBUG"
macro is not set, dev_dbg() already defaults to a no-operation, though
one that lets the compiler know that the arguments are used, and lets
it check the format string.
Fixing this also simplifies the driver.
Fixes:
|
|
|
Gregor Boirie
|
03b262f2bb |
iio:pressure: initial zpa2326 barometer support
Introduce driver for Murata ZPA2326 pressure and temperature sensor: http://www.murata.com/en-us/products/productdetail?partno=ZPA2326-0311A-R Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> |
|
|
Greg Kroah-Hartman
|
552edf8d79 |
Second set of iio new device support, features and cleanups for the 4.9 cycle.
New device support
* ad8801 dac
- new driver supporting ad8801 and ad8803 DACs.
* adc12138
- new driver supporting TI adc12130/adc12132 and adc12138 ADCs.
* ltc2485 adc
- new driver
* mxc6255
- add support for the mxc6225 part name and fixup the ID check so it works.
* vz89x VOC sensor
- add support for the vz89te part which drops the voc_short channel and adds
CRCs compared to other supported parts.
New features
* core
- immutable triggers. These effectively grant exclusive control over a
trigger. The typical usecase is a device representing an analog part
(perhaps a MUX) that needs to control the sampling of a downstream
ADC.
- resource managed trigger registration and triggered_buffer_init.
- iio_push_event now protected against case of the event interface
registration not having yet occured. Only matters if an interrupt
can occur during this window - might happen on shared interrupt lines.
- helper to let a driver query if the trigger it is using is provided by
itself (using the convention of both device and trigger having the same
parent).
* tools
- iio-utils. Used channel modifier scaling in preference to generic scaling
when both exist.
* at91-adc
- Add support for touchscreen switches closure time needed by some newer
parts.
* stx104
- support the ADC channels on this ADC/DAC board. As these are the primary
feature of the board also move the driver to the iio/adc directory.
* sx9500
- device tree bindings.
Cleanups / Fixes
* ad5755
- fix an off-by-one on devnr limit check (introduced earlier this cycle)
* ad7266
- drop NULL check on devm_regulator_get_optional as it can't return NULL.
* ak8974
- avoid an unused functional warning due to rework in PM core code.
- remove .owner field setting as done by i2c_core.
* ina2xx
- clear out a left over debug field from chip global data.
* hid-sensors
- avoid an unused functional warning due to rework in PM core code.
* maxim-thermocouple
- fix non static symbol warnings.
* ms5611
- fetch and enable regulators unconditionally when they aren't optional.
* sca3000
- whitespace cleanup.
* st_sensors
- fetch and enable regulators unconditionally rather than having them
supported as optional regulators (missunderstanding on my part amongst
others a while back)
- followup to previous patch fixes error checking on the regulators.
- mark symbols static where possible.
- use the 'is it my trigger' help function. This prevents the odd case
of another device triggering from the st-sensors trigger whilst the
st-sensors trigger is itself not using it but rather using say an hrtimer.
* ti-ads1015
- add missing of_node_put.
* vz89x
- rework to all support of new devices.
- prevent reading of a corrupted buffer.
- fixup a return value of 0/1 in a bool returning function.
Address updates
- Vlad Dogaru email address change.
-----BEGIN PGP SIGNATURE-----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=V1xL
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.9b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of iio new device support, features and cleanups for the 4.9 cycle.
New device support
* ad8801 dac
- new driver supporting ad8801 and ad8803 DACs.
* adc12138
- new driver supporting TI adc12130/adc12132 and adc12138 ADCs.
* ltc2485 adc
- new driver
* mxc6255
- add support for the mxc6225 part name and fixup the ID check so it works.
* vz89x VOC sensor
- add support for the vz89te part which drops the voc_short channel and adds
CRCs compared to other supported parts.
New features
* core
- immutable triggers. These effectively grant exclusive control over a
trigger. The typical usecase is a device representing an analog part
(perhaps a MUX) that needs to control the sampling of a downstream
ADC.
- resource managed trigger registration and triggered_buffer_init.
- iio_push_event now protected against case of the event interface
registration not having yet occured. Only matters if an interrupt
can occur during this window - might happen on shared interrupt lines.
- helper to let a driver query if the trigger it is using is provided by
itself (using the convention of both device and trigger having the same
parent).
* tools
- iio-utils. Used channel modifier scaling in preference to generic scaling
when both exist.
* at91-adc
- Add support for touchscreen switches closure time needed by some newer
parts.
* stx104
- support the ADC channels on this ADC/DAC board. As these are the primary
feature of the board also move the driver to the iio/adc directory.
* sx9500
- device tree bindings.
Cleanups / Fixes
* ad5755
- fix an off-by-one on devnr limit check (introduced earlier this cycle)
* ad7266
- drop NULL check on devm_regulator_get_optional as it can't return NULL.
* ak8974
- avoid an unused functional warning due to rework in PM core code.
- remove .owner field setting as done by i2c_core.
* ina2xx
- clear out a left over debug field from chip global data.
* hid-sensors
- avoid an unused functional warning due to rework in PM core code.
* maxim-thermocouple
- fix non static symbol warnings.
* ms5611
- fetch and enable regulators unconditionally when they aren't optional.
* sca3000
- whitespace cleanup.
* st_sensors
- fetch and enable regulators unconditionally rather than having them
supported as optional regulators (missunderstanding on my part amongst
others a while back)
- followup to previous patch fixes error checking on the regulators.
- mark symbols static where possible.
- use the 'is it my trigger' help function. This prevents the odd case
of another device triggering from the st-sensors trigger whilst the
st-sensors trigger is itself not using it but rather using say an hrtimer.
* ti-ads1015
- add missing of_node_put.
* vz89x
- rework to all support of new devices.
- prevent reading of a corrupted buffer.
- fixup a return value of 0/1 in a bool returning function.
Address updates
- Vlad Dogaru email address change.
|
|
|
Crt Mori
|
6751607488 |
iio: fetch and enable regulators unconditionally
This patch is inspired by a comment of Jonathan Cameron on patch of
Linus Walleij commit
|
|
|
Greg Kroah-Hartman
|
fbc1ec2efe |
Merge 4.8-rc5 into char-misc-next
We want the fixes in here for merging and testing. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
|
|
Linus Walleij
|
832c8232dd |
misc: retire the old BMP085 driver
Patches merged to the IIO BMP085 driver makes it fully compliant with all features found in this old misc driver. Retire this old driver in favor of the new one in the proper subsystem. Cc: Jonathan Cameron <jic23@cam.ac.uk> Cc: Marek Belisko <marek@goldelico.com> Acked-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
|
|
Linus Walleij
|
31f453eac5 |
iio: pressure: bmp280: fix runtime suspend/resume crash
In commit |
|
|
Wei Yongjun
|
bb9947c3a1 |
iio: pressure: bmp280: fix wrong pointer passed to PTR_ERR()
PTR_ERR should access the value just tested by IS_ERR, otherwise the wrong error code will be returned. Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org> |
|
|
Gregor Boirie
|
060a518eda |
iio:st_pressure: clean useless static channel initializers
Some static channels are explicitly initialized with default values. Remove them to enhance readability. Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com> Tested-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org> |
|
|
Gregor Boirie
|
85d79136d3 |
iio:st_pressure:lps22hb: temperature support
Implement lps22hb temperature sampling channel. Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com> Tested-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org> |
|
|
Gregor Boirie
|
05167cdce0 |
iio:st_pressure:lps22hb: open drain support
Add support for open drain interrupt line. Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> |
|
|
Gregor Boirie
|
b4701fd692 |
iio:st_pressure: temperature triggered buffering
Enable support for triggered buffering of temperature samples. Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com> Tested-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org> |