Add the digital-mic support with ALC262 auto model.
The new ALC262 models have the digital mic at NID 0x12. This widget
isn't checked in the current alc262_auto_create_analog_input_ctls()
since it's under 0x18. So, just reuse the routine for alc269 to fix
the behavior.
But, it doesn't suffice: the digital mic is supported only with the
ADC0, we have to exclude other ADCs when d-mic is detected.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix the check of the input-source type by checking the widget type of
each capture-source item. Since some codecs can have both the mixer
and selector types depending on the ADC, alc_mux_enum_put() needs to
check each widget.
With this change, spec->capture_style gets unneeded, so it's removed,
too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit f9e336f65b
ALSA: hda - Unify capture mixer creation in realtek codes
removed the "Input Source" mixer element creation for toshiba-s06 model
because it contains a digital-mic input.
This patch take the control back.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
Fix the comparison of unsigned int that causes a compile warning below
by changing to the right signed type:
patch_sigmatel.c: In function ‘stac92xx_vref_set’:
patch_sigmatel.c:658: warning: comparison of unsigned expression < 0 is always false
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There's a large 500ms delay in snd_via82xx_codec_wait() that, at least
on my hardware, appears to be unnecessary. The rest of the init of
the card works without logging any warnings or errors and both audio
and mixer settings work.
This adds an "nodelay" parameter to disable this (undocumented in the
code) large delay improving bootup time by 489-500ms.
[ 1.034217] initcall alsa_card_via82xx_init+0x0/0x16 returned 0 after 505757 usecs
vs.
[ 0.533136] initcall alsa_card_via82xx_init+0x0/0x16 returned 0 after 15915 usecs
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allow unknown PCI SSIDs for emu20k1 and emu20k2 as "unknown" model.
Also, add a black-list check in case any device has to be listed
as "unsupported". It has a negative value in the pci quirk entry.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The selected 4930G model seemed to keep the subwoofer 'tuba'
function from operating correctly. Removing the existing PCI
ID match made this work again, but it was mapped to 'Side'
instead of to LFE as one would expect.
This attempts to enable all functionality and keep the amount
of available mixer sliders low. Any slider that had no audible
effect on the output audio has been removed, and as such EAPD
is not currently enabled.
Signed-off-by: Tony Vroon <tony@linx.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We're about to make DMA_nnBIT_MASK() emit `deprecated' warnings. Convert the
remaining stragglers which are visible to the x86_64 build.
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Eric Moore <Eric.Moore@lsil.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Yi Zou <yi.zou@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Correct some cut+paste typos from 'tagra' to 'targa'.
Signed-off-by: Sasha Alexandr <brina_keith@ns.sympatico.ca>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCM x-fi native update routine can cause deadlocks when the
trigger(START) is called while the stream is running.
This patch fixes the deadlock by just postponing the pcm period update
to the next possible wake-up. Also it adds the flip of ti->running
flag (just to be sure as now).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCM pointer callback sometimes returns invalid positions and this
screws up the hw_ptr updater in PCM core. Especially since now the
jiffies check is optional with xrun_debug, the invalid position is
handled as is, and causes serious sound skips, etc.
This patch simplifies the position-fix strategy in intel8x0 to be more
robust:
- just falls back to the last position if bogus position is detected
- another sanity check for the backward move of the position due to
a race of register update and the base-index update
This patch is applicable also for 2.6.30.
Tested-by: David Miller <davem@davemloft.net>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The spinlock in atc can cause a sleep in lock:
Kernel failure message 1:
BUG: sleeping function called from invalid context at mm/slub.c:1599
in_atomic(): 0, irqs_disabled(): 1, pid: 2537, name: gstreamer-prope
Pid: 2537, comm: gstreamer-prope Tainted: P
2.6.29.4-167.fc11.x86_64 #1
Call Trace:
[<ffffffff8103ff0f>] __might_sleep+0x10b/0x110
[<ffffffff810cd734>] __kmalloc+0x73/0x130
[<ffffffffa0b4b142>] ? daio_rsc_init+0xaa/0x125 [snd_ctxfi]
[<ffffffffa0b4b212>] dao_rsc_init+0x55/0x1c0 [snd_ctxfi]
[<ffffffffa0b4b3d2>] dao_rsc_reinit+0x55/0x5d [snd_ctxfi]
[<ffffffff813abd6c>] ? _spin_lock_irqsave+0x32/0x3b
[<ffffffffa0b454fe>] atc_spdif_out_passthru+0x92/0x136 [snd_ctxfi]
...
Since the lock path is no critical path, it can be gracefully
replaced with a mutex.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
trivial patch to support the alsa module parameters `index', `id'
and `enable'
Signed-off-by: Tim Blechmann <tim@klingt.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* topic/oxygen:
sound: virtuoso: add Xonar Essence ST support
sound: virtuoso: enable HDAV S/PDIF input
sound: virtuoso: add another DX PCI ID
sound: oxygen: reset DMA when stream is closed
* topic/misc:
ALSA: sgio2audio.c: clean up checking
ALSA: burgundy: timeout message is off by one.
ALSA: bt87x - Add a quirk entry for Askey Computer Corp. MagicTView'99
ALSA: parisc/harmony: fix printk format warning
ALSA: keywest: Get rid of useless i2c_device_name() macro
* topic/maya44:
ALSA: ice1724 - Add ESI Maya44 support
ALSA: ice1724 - Allow spec driver to create own routing controls
ALSA: ice1724 - Add PCI postint to reset sequence
ALSA: ice1724 - Clean up definitions of DMA records
ALSA: ice1724 - Check error in set_rate function
Currently the PCM resources are allocated only once and ever in prepare
callback, assuming that the PCM parameters are never changed. But it's
not true.
This patch adds the call of atc->pcm_release_resources() at hw_params
and hw_free callbacks to assure that the PCM setup is done correctly
for each h/w parameter changes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The SRC instances may not exist when PCM pointer callback is called at
the state before initialization is finished. Add the NULL check just
to be sure.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added use_system_timer module option to force to use the system timer
instead of emu20k1 timer irq for debugging.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CTUAA should be checked instead of CTHENDRIX. The latter is for 20k2 chip.
Also, fixed the detection of UAA/HENDRIX models by fixing the mask bits.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clean up probe routines and model detection routines so that the driver
won't call and check the PCI subsystem id at each time.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added 7.1 support for MSI GX620 and jack quirk.
Reference: kernel bug#13430
http://bugzilla.kernel.org/show_bug.cgi?id=13430
Signed-off-by: David Heidelberger <d.okias@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
EFX playback stream should have periods_min = 2 to avoid the buffer
position overflow (due to restrictions of the pcm-indirect helper).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Clean up Hungarian coding style
- Don't use static variables for I2C information; this unables to use
multiple instances. Now they are stored in struct hw20k2 fields.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Optimize the timer update routine to look up wall clock once instead of
checking the position of each stream at each timer update.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Use static tables instead of assigining each funciton pointer
- Add __devinit* to appropriate places; pcm, mixer and timer cannot be
marked because they are kept in the function table that lives long
- Move create_alsa_devs function out of struct ct_atc to mark it
__devinit
Signed-off-by: Takashi Iwai <tiwai@suse.de>
emu20k1 has a native timer interrupt based on the audio clock, which
is more accurate than the system timer (from the synchronization POV).
This patch adds the code to handle this with multiple streams.
The system timer is still used on emu20k2, and can be used also for
emu20k1 easily by changing USE_SYSTEM_TIMER to 1 in cttimer.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
with BIOS probing only we offer a non functional headphone swith and
volume slider.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The UAA-mode check in hwct20k1.c is implemented with the endian-dependent
codes. Fix to be more portable (and readable).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix this build error when CONFIG_PM is not set:
ound/pci/hda/hda_intel.c: In function 'azx_bus_reset':
sound/pci/hda/hda_intel.c:1270: error: implicit declaration of function 'snd_pcm_suspend_all'
sound/pci/hda/hda_intel.c:1271: error: implicit declaration of function 'snd_hda_suspend'
sound/pci/hda/hda_intel.c:1272: error: implicit declaration of function 'snd_hda_resume'
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable all three capture channels, including the missing nid 7 which is
the only one capable of capturing DMIC input
Enable Headphone amp for the HP jack. This causes a volume boost for
headphones, but does not cause any noticeable effect for light loads
like other amps, so there is no need to make it configurable.
Add Input Mix capture mux setting to capture the output of the playback
input mux (that is, what goes out the speakers except for PCM)
Hack another coef register because the stereo DMIC for some reason
produces a nonstandard sum/difference signal. I found a bit to make it
just use the sum signal for both channels, which makes it behave like a
standard mono microphone. The stereo is useless anyway (they're 1cm apart).
Tested working: Three capture channels, mic in, line in, DMIC.
Tested not working: CD. Not sure why, might be unconnected in the actual
hardware or a CD drive issue.
Also looked at SPDIF. It appears to work (emitter lights up inside the
HP out jack) but I lack a proper miniTOSLINK cable to test it.
Signed-off-by: Hector Martin <hector@marcansoft.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove the limitation of PAGE_SIZE to be 4k by defining the own
page size and macros for 4k. 8kb page size could be natively supported,
but it's disabled right now for simplicity.
Also, clean up using upper_32_bits() macro.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The device seems supporting only U8, S16, S24_3LE, S32. Other linear
formats result in bad outputs.
Also, added the support for 32bit float format, which wasn't listed
in the original code.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
PCM names for surround streams should be also fixed as well as the mixer
element names. Also, a bit clean up for PCM name setup.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We usually pick up "Surround" mixer for the rear output, and "Side"
for the extra surround. Fix the channel mapping to follow it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The prepare callback can be called multiple times, thus it needs to
release and acquire the resource again by itself at the second or later
call.
Simply add pcm_release_resources() at the beginning of each prepare
callback in ctatc.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SNDRV_PCM_SUBCLASS_GENERIC_MIX is mostly for h/w multi-stream playback
devices, but ca0106 and emu10k1x don't support it (unlike emu10k1).
We shouldn't set that flag to avoid confusion.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Although the vmaster controls are created, they aren't registered thus
they don't appear in the real world. Added the missing snd_ctl_add()
calls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
Short story: this laptop has 5.1 built-in speakers which you *really*
want to use (the not-so-"sub" woofer is what makes the audio above
average for a laptop), so 6-channel support is important (plus a decent
asound.conf to upmix stereo). It also has the 3 typical jacks that ought
to have a selectable mode. And it's based on ALC889, which sucks.
Rationale/explanations:
The const_channel_count stuff was added because, for a laptop like this,
you always have 6 channels available (internal speakers) but still need
to set the mode for the 3 external jacks. Therefore, the device always
needs to be in 6-channel mode but there still needs to be a mixer
control for the jack mode. You could use line/mic-in at the same time as
the 6 internal speakers, for example. You might be tempted to make it
even smarter by dynamically switching the max channel count when
headphones are plugged in (therefore muting the internal speakers and
reducing the physical channel count to the jack channel mode), but as a
user I consider this to be harmful because I want the audio to blow up
to 6 channels / upmixed as soon as I unplug the headphones, and having
opened the device while in 2-channel mode would prevent this from
working (and always making 6-channel mode available doesn't do any harm).
The hardware needs EAPD turned on and the DACs routed to the internal
speaker pins, so the patch adds those verbs.
The ALC889 CLFE and subsequent (side/aux, here unused) DACs do NOT work
by default, at least here. I wasted much time trying to talk to
Realtek/pshou about this, but they just kept sending me useless updates
to patch_realtek.c that did nothing relevant. In the end I gave up and
brute forced the issue by trying to flip every bit in the proprietary
coefficient registers, and eventually found the two magic registers that
need to be cleared to enable all DACs. I have only heard Acer users
complain, but that might be because ALC889 is pretty new and using 5.1
(and noticing the missing center/lfe channels) might not be that common.
If this is a generalized issue with all ALC889 systems then those verbs
should probably be moved to a common verb array.
The internal mic is untested and probably doesn't work.
These settings will probably work for other Acer Gemstone laptops with
the same 5.1 speaker config. When identified, those should be added to
the PCI subsystem ID list.
Signed-off-by: Hector Martin <hector@marcansoft.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The reset of a BUS controller during operations is somehow risky and
shouldn't be done inevitably for devices that have apparently no such
codec-communication problems.
This patch adds the check of the hardware and limits the bus-reset
capability.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some machines machine cause a severe CORB/RIRB stall in certain
weird conditions, such as PA access at the start up together with
fglrx driver. This seems unable to be recovered without the controller
reset.
This patch allows the bus controller reset at critical errors so
that the communication gets recovered again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, LG R510 is only able to produce sound on headphones, the
internal speakers are not working.
The user tested and confirmed that with model=Dell headphones,
internal speakers and the microphone are working flawlessly.
Tested-by: Serdar Soytetir <tulliana@gmail.com>
Signed-off-by: Ozan Çağlayan <ozan@pardus.org.tr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
this is a patch against current snapshot that adds:
6 channels support for the MB5 model
Signed-off-by: Kacper Szczesniak <kacper@qwe.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix issues for 3 generations of HP workstations.
The modest modifications do the following:
1. Change the second MIC from device 3 to device 1
2. Init the "boost" values to "0" by default
From: John Brown <john.brown3@hp.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch changes Line In as Out Switch and Mic In as Out Switch to
enums for consistency, and causes all mic and line in ports to be probed
and controls to be added appropriately.
Signed-off-by: Nickolas Lloyd <ultrageek.lloyd@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ICH6_GCTL_RESET was wrongly set to another bit by the commit
b21fadb9c1. This caused a problem when
the codec needs really a reset (e.g. recovering from the communication
error at probe).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of mangling the CONFIG_* variables in the makefiles over and
over, set a few helper variables in Kconfig.
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai