!!'s behaviour isn't that obvious and sparse complained about it, so
let's replace it with a ternary condition.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
CCS811 has different I2C register maps in boot and application mode. When
CCS811 is in boot mode, register APP_START (0xF4) is used to transit the
firmware state from boot to application mode. However, APP_START is not a
valid register location when CCS811 is in application mode (refer to
"CCS811 Bootloader Register Map" and "CCS811 Application Register Map" in
CCS811 datasheet). The driver should not attempt to perform a write to
APP_START while CCS811 is in application mode, as this is not a valid or
documented register location.
When prob function is being called, the driver assumes the CCS811 sensor
is in boot mode, and attempts to perform a write to APP_START. Although
CCS811 powers-up in boot mode, it may have already been transited to
application mode by previous instances, e.g. unload and reload device
driver by the system, or explicitly by user. Depending on the system
design, CCS811 sensor may be permanently connected to system power source
rather than power controlled by GPIO, hence it is possible that the sensor
is never power reset, thus the firmware could be in either boot or
application mode at any given time when driver prob function is being
called.
This patch checks the STATUS register before attempting to send a write to
APP_START. Only if the firmware is not in application mode and has valid
firmware application loaded, then it will continue to start transiting the
firmware boot to application mode.
Signed-off-by: Richard Lai <richard@richardman.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The resistance member in ccs811_reading struct is an unsigned 16-bit
integer variable used to store RAW_DATA register bytes read from CCS811.
It is kind of misleading to name this struct member as resistance.
About the RAW_DATA register bytes, the CCS811 datasheet states that:
-----
Two byte read only register which contains the latest readings from the
sense resistor.
The most significant 6 bits of the Byte 0 contain the value of the current
through the sensor (0μA to 63μA).
The lower 10 bits contain (as computed from the ADC) the readings of the
voltage across the sensor with the selected current (1023 = 1.65V)"
-----
Hence, the RAW_DATA register byte contains information about electric
current and voltage of the CCS811 sensor. Calling this struct member
'resistance' is kind of misleading, although both electric current and
voltage are needed to calculate the electrical resistance of the sensor
using Ohm's law, V = I x R, in which a new channel type of IIO_RESISTANCE
may be added to the driver in the future.
Signed-off-by: Richard Lai <richard@richardman.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ISA_BUS_API Kconfig option enables the compilation of the ISA bus
driver. The ISA bus driver does not perform any hardware interaction,
and is instead just a thin layer of software abstraction to eliminate
boilerplate code common to ISA-style device drivers. Since ISA_BUS_API
has no dependencies and does not jeopardize the integrity of the system
when enabled, drivers should select it when the ISA bus driver
functionality is needed.
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Outside of IIO
* Strongly typed 64bit int_sqrt function needed by the mlx90632
New device support
* adc081s
- New driver supporting adc081s, adc101s and adc121s TI ADCs.
* ad5272
- New driver supproting the ad5272 and ad5274 ADI digital potentiometers
with DT bindings.
* axp20x_adc
- support the AXP813 ADC - includes rework patches to prepare for this.
* mlx90632
- New driver with dt bindings for this IR temperature sensor.
Features
* axp20x_adc
- Add DT bindings and probing.
* dht11
- The sensor has a wider range than advertised in the datasheet - support it.
* st_lsm6dsx
- Add hardware timestamp su9pport.
Cleanups
* ABI docs
- Update email contact for Matt Ranostay
* SPDX changes
- Matt Ranostay has moved his drivers over to SPDX. Currently we are making
this an author choice in IIO.
* ad7192
- Disable burnout current on misconfiguration. No actually effect as
they simply won't work otherwise.
* ad7476
- Drop a license definition that was replicating information in SPDX tag.
* ade7758
- Expand buf_lock to cover both buffer and state protection allowing
unintented uses of mlock in the core to be removed.
* ade7759
- Align parameters to opening parenthesis.
* at91_adc
- Depend on sysfs instead of selecting it - for try wide consistency.
* ccs811
- trivial naming type for a define.
* ep93xx
- Drop a redundant return as a result checking platform_get_resource.
* hts221
- Regmap conversion which simplifies the driver somewhat.
- Clean up some restricted endian cast warnings.
- Drop a trailing whitespace from a comment
- Drop an unnecessary get_unaligned by changing to the right 16bit data type.
* ms5611
- Fix coding style in the probe function (whitespace)
* st_accel
- Use strlcpy instead of strncpy to avoid potentially truncating a string.
-----BEGIN PGP SIGNATURE-----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=CH1K
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.17a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of new devices, features and cleanups for IIO in the 4.17 cycle.
Outside of IIO
* Strongly typed 64bit int_sqrt function needed by the mlx90632
New device support
* adc081s
- New driver supporting adc081s, adc101s and adc121s TI ADCs.
* ad5272
- New driver supproting the ad5272 and ad5274 ADI digital potentiometers
with DT bindings.
* axp20x_adc
- support the AXP813 ADC - includes rework patches to prepare for this.
* mlx90632
- New driver with dt bindings for this IR temperature sensor.
Features
* axp20x_adc
- Add DT bindings and probing.
* dht11
- The sensor has a wider range than advertised in the datasheet - support it.
* st_lsm6dsx
- Add hardware timestamp su9pport.
Cleanups
* ABI docs
- Update email contact for Matt Ranostay
* SPDX changes
- Matt Ranostay has moved his drivers over to SPDX. Currently we are making
this an author choice in IIO.
* ad7192
- Disable burnout current on misconfiguration. No actually effect as
they simply won't work otherwise.
* ad7476
- Drop a license definition that was replicating information in SPDX tag.
* ade7758
- Expand buf_lock to cover both buffer and state protection allowing
unintented uses of mlock in the core to be removed.
* ade7759
- Align parameters to opening parenthesis.
* at91_adc
- Depend on sysfs instead of selecting it - for try wide consistency.
* ccs811
- trivial naming type for a define.
* ep93xx
- Drop a redundant return as a result checking platform_get_resource.
* hts221
- Regmap conversion which simplifies the driver somewhat.
- Clean up some restricted endian cast warnings.
- Drop a trailing whitespace from a comment
- Drop an unnecessary get_unaligned by changing to the right 16bit data type.
* ms5611
- Fix coding style in the probe function (whitespace)
* st_accel
- Use strlcpy instead of strncpy to avoid potentially truncating a string.
One nasty very old crash around polling for buffers that aren't there
- though that can only cause effects on drivers that support events
but not buffers.
* buffer / kfifo handling in the core.
- Check there is a buffer and return 0 from poll directly if there
isn't. Poll doesn't make sense in this circumstances, but best to close
the hole.
* ad5933
- Change the marked buffer mode to a software buffer as the meaning of
the hardware buffer label has long since changed and this uses a front
end software buffer anyway.
* ad7192
- Fix the fact the external clock frequency was only set when using the
internal clock which was less than helpful.
* adis_lib
- Initialize the trigger before requesting the interrupt. Some newer
parts can power up with interrupt generation enabled so ordering now
matters.
* aspeed-adc
- Fix an errror handling path as labels and general ordering were wrong.
* srf08
- Fix a link error due to undefined devm_iio_triggered_buffer_setup.
* stm32-adc
- Fix error handling unwind squence in stm32h7_adc_enable.
-----BEGIN PGP SIGNATURE-----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=x9oo
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.16a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First round of IIO fixes for the 4.16 cycle.
One nasty very old crash around polling for buffers that aren't there
- though that can only cause effects on drivers that support events
but not buffers.
* buffer / kfifo handling in the core.
- Check there is a buffer and return 0 from poll directly if there
isn't. Poll doesn't make sense in this circumstances, but best to close
the hole.
* ad5933
- Change the marked buffer mode to a software buffer as the meaning of
the hardware buffer label has long since changed and this uses a front
end software buffer anyway.
* ad7192
- Fix the fact the external clock frequency was only set when using the
internal clock which was less than helpful.
* adis_lib
- Initialize the trigger before requesting the interrupt. Some newer
parts can power up with interrupt generation enabled so ordering now
matters.
* aspeed-adc
- Fix an errror handling path as labels and general ordering were wrong.
* srf08
- Fix a link error due to undefined devm_iio_triggered_buffer_setup.
* stm32-adc
- Fix error handling unwind squence in stm32h7_adc_enable.
Add GPLv2+ SPDX identifier and update email for author's drivers.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If no iio buffer has been set up and poll is called return 0.
Without this check there will be a null pointer dereference when
calling poll on a iio driver without an iio buffer.
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Windfeldt-Prytz <stefan.windfeldt@axis.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The adis_probe_trigger() creates a new IIO trigger and requests an
interrupt associated with the trigger. The interrupt uses the generic
iio_trigger_generic_data_rdy_poll() function as its interrupt handler.
Currently the driver initializes some fields of the trigger structure after
the interrupt has been requested. But an interrupt can fire as soon as it
has been requested. This opens up a race condition.
iio_trigger_generic_data_rdy_poll() will access the trigger data structure
and dereference the ops field. If the ops field is not yet initialized this
will result in a NULL pointer deref.
It is not expected that the device generates an interrupt at this point, so
typically this issue did not surface unless e.g. due to a hardware
misconfiguration (wrong interrupt number, wrong polarity, etc.).
But some newer devices from the ADIS family start to generate periodic
interrupts in their power-on reset configuration and unfortunately the
interrupt can not be masked in the device. This makes the race condition
much more visible and the following crash has been observed occasionally
when booting a system using the ADIS16460.
Unable to handle kernel NULL pointer dereference at virtual address 00000008
pgd = c0004000
[00000008] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.9.0-04126-gf9739f0-dirty #257
Hardware name: Xilinx Zynq Platform
task: ef04f640 task.stack: ef050000
PC is at iio_trigger_notify_done+0x30/0x68
LR is at iio_trigger_generic_data_rdy_poll+0x18/0x20
pc : [<c042d868>] lr : [<c042d924>] psr: 60000193
sp : ef051bb8 ip : 00000000 fp : ef106400
r10: c081d80a r9 : ef3bfa00 r8 : 00000087
r7 : ef051bec r6 : 00000000 r5 : ef3bfa00 r4 : ee92ab00
r3 : 00000000 r2 : 00000000 r1 : 00000000 r0 : ee97e400
Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment none
Control: 18c5387d Table: 0000404a DAC: 00000051
Process swapper/0 (pid: 1, stack limit = 0xef050210)
[<c042d868>] (iio_trigger_notify_done) from [<c0065b10>] (__handle_irq_event_percpu+0x88/0x118)
[<c0065b10>] (__handle_irq_event_percpu) from [<c0065bbc>] (handle_irq_event_percpu+0x1c/0x58)
[<c0065bbc>] (handle_irq_event_percpu) from [<c0065c30>] (handle_irq_event+0x38/0x5c)
[<c0065c30>] (handle_irq_event) from [<c0068e28>] (handle_level_irq+0xa4/0x130)
[<c0068e28>] (handle_level_irq) from [<c0064e74>] (generic_handle_irq+0x24/0x34)
[<c0064e74>] (generic_handle_irq) from [<c021ab7c>] (zynq_gpio_irqhandler+0xb8/0x13c)
[<c021ab7c>] (zynq_gpio_irqhandler) from [<c0064e74>] (generic_handle_irq+0x24/0x34)
[<c0064e74>] (generic_handle_irq) from [<c0065370>] (__handle_domain_irq+0x5c/0xb4)
[<c0065370>] (__handle_domain_irq) from [<c000940c>] (gic_handle_irq+0x48/0x8c)
[<c000940c>] (gic_handle_irq) from [<c0013e8c>] (__irq_svc+0x6c/0xa8)
To fix this make sure that the trigger is fully initialized before
requesting the interrupt.
Fixes: ccd2b52f4a ("staging:iio: Add common ADIS library")
Reported-by: Robin Getz <Robin.Getz@analog.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This particular constant was named with prefix "CCS881", which should be
"CCS811" instead, just like the rest of constant names in the file, as this
driver implementation is for AMS CCS811 sensor. "CCS881" could literally be
referring to another sensor product unrelated to AMS CCS811 sensor.
Signed-off-by: Richard Lai <richard@richardman.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch fixes the checkpatch.pl warning and error:
iio/pressure/ms5611.h:66: ERROR: code indent should use tabs where possible
iio/pressure/ms5611.h:66: WARNING: please, no spaces at the start of a line
iio/pressure/ms5611.h:66: ERROR: "foo* bar" should be "foo *bar"
Signed-off-by: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The old code was based on a DHT11 datasheet which specifies a measurement
range of 20%-90% RH. Turns out the sensor actually reports values outside
this range, so we should support it as far as possible.
Reported-by: Edward Attfield <edward@attfield.ca>
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add implementation for Analog Devices AD5272 and AD5274 digital
potentiometer devices.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Functions for triggered buffer support are needed by this module.
If they are not defined accidentally by another driver, there's an error
thrown out while linking.
Add a select of IIO_BUFFER and IIO_TRIGGERED_BUFFER in the Kconfig file.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Fixes: a831959371 ("iio: srf08: add triggered buffer support")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Melexis has just released Infra Red temperature sensor MLX90632 used
for contact-less temperature measurement. Driver provides basic
functionality for reporting object (and ambient) temperature with
support for object emissivity.
Signed-off-by: Crt Mori <cmo@melexis.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the big Staging and IIO driver patches for 4.16-rc1.
There is the normal amount of new IIO drivers added, like all releases.
The networking IPX and the ncpfs filesystem are moved into the staging
tree, as they are on their way out of the kernel due to lack of use
anymore.
The visorbus subsystem finall has started moving out of the staging tree
to the "real" part of the kernel, and the most and fsl-mc codebases are
almost ready to move out, that will probably happen for 4.17-rc1 if all
goes well.
Other than that, there is a bunch of license header cleanups in the
tree, along with the normal amount of coding style churn that we all
know and love for this codebase. I also got frustrated at the
Meltdown/Spectre mess and took it out on the dgnc tty driver, deleting
huge chunks of it that were never even being used.
Full details of everything is in the shortlog.
All of these patches have been in linux-next for a while with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWnLxoA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk4vgCgjeMlwhtar65DIticIRj626EFxiQAnjGmH8Kd
d9Xz2Piq8X47uSsC/6AE
=xxMT
-----END PGP SIGNATURE-----
Merge tag 'staging-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO updates from Greg KH:
"Here is the big Staging and IIO driver patches for 4.16-rc1.
There is the normal amount of new IIO drivers added, like all
releases.
The networking IPX and the ncpfs filesystem are moved into the staging
tree, as they are on their way out of the kernel due to lack of use
anymore.
The visorbus subsystem finall has started moving out of the staging
tree to the "real" part of the kernel, and the most and fsl-mc
codebases are almost ready to move out, that will probably happen for
4.17-rc1 if all goes well.
Other than that, there is a bunch of license header cleanups in the
tree, along with the normal amount of coding style churn that we all
know and love for this codebase. I also got frustrated at the
Meltdown/Spectre mess and took it out on the dgnc tty driver, deleting
huge chunks of it that were never even being used.
Full details of everything is in the shortlog.
All of these patches have been in linux-next for a while with no
reported issues"
* tag 'staging-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (627 commits)
staging: rtlwifi: remove redundant initialization of 'cfg_cmd'
staging: rtl8723bs: remove a couple of redundant initializations
staging: comedi: reformat lines to 80 chars or less
staging: lustre: separate a connection destroy from free struct kib_conn
Staging: rtl8723bs: Use !x instead of NULL comparison
Staging: rtl8723bs: Remove dead code
Staging: rtl8723bs: Change names to conform to the kernel code
staging: ccree: Fix missing blank line after declaration
staging: rtl8188eu: remove redundant initialization of 'pwrcfgcmd'
staging: rtlwifi: remove unused RTLHALMAC_ST and RTLPHYDM_ST
staging: fbtft: remove unused FB_TFT_SSD1325 kconfig
staging: comedi: dt2811: remove redundant initialization of 'ns'
staging: wilc1000: fix alignments to match open parenthesis
staging: wilc1000: removed unnecessary defined enums typedef
staging: wilc1000: remove unnecessary use of parentheses
staging: rtl8192u: remove redundant initialization of 'timeout'
staging: sm750fb: fix CamelCase for dispSet var
staging: lustre: lnet/selftest: fix compile error on UP build
staging: rtl8723bs: hal_com_phycfg: Remove unneeded semicolons
staging: rts5208: Fix "seg_no" calculation in reset_ms_card()
...
Pull poll annotations from Al Viro:
"This introduces a __bitwise type for POLL### bitmap, and propagates
the annotations through the tree. Most of that stuff is as simple as
'make ->poll() instances return __poll_t and do the same to local
variables used to hold the future return value'.
Some of the obvious brainos found in process are fixed (e.g. POLLIN
misspelled as POLL_IN). At that point the amount of sparse warnings is
low and most of them are for genuine bugs - e.g. ->poll() instance
deciding to return -EINVAL instead of a bitmap. I hadn't touched those
in this series - it's large enough as it is.
Another problem it has caught was eventpoll() ABI mess; select.c and
eventpoll.c assumed that corresponding POLL### and EPOLL### were
equal. That's true for some, but not all of them - EPOLL### are
arch-independent, but POLL### are not.
The last commit in this series separates userland POLL### values from
the (now arch-independent) kernel-side ones, converting between them
in the few places where they are copied to/from userland. AFAICS, this
is the least disruptive fix preserving poll(2) ABI and making epoll()
work on all architectures.
As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and
it will trigger only on what would've triggered EPOLLWRBAND on other
architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered
at all on sparc. With this patch they should work consistently on all
architectures"
* 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
make kernel-side POLL... arch-independent
eventpoll: no need to mask the result of epi_item_poll() again
eventpoll: constify struct epoll_event pointers
debugging printk in sg_poll() uses %x to print POLL... bitmap
annotate poll(2) guts
9p: untangle ->poll() mess
->si_band gets POLL... bitmap stored into a user-visible long field
ring_buffer_poll_wait() return value used as return value of ->poll()
the rest of drivers/*: annotate ->poll() instances
media: annotate ->poll() instances
fs: annotate ->poll() instances
ipc, kernel, mm: annotate ->poll() instances
net: annotate ->poll() instances
apparmor: annotate ->poll() instances
tomoyo: annotate ->poll() instances
sound: annotate ->poll() instances
acpi: annotate ->poll() instances
crypto: annotate ->poll() instances
block: annotate ->poll() instances
x86: annotate ->poll() instances
...
Introduce hw timestamp support instead of compute sample timestamps
according to interrupt rate and configured watermark. LSM6DSx based
devices are able to queue in hw FIFO the time reference of data
sampling
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Using an SPDX tag. Remove a license notice to keep
the whole purpose of using an SPDx id.
Signed-off-by: Milan Stevanovic <milan.o.stevanovic@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add Linux device driver for TI single-channel CMOS
8/10/12-bit analog-to-digital converter with a
high-speed serial interface.
Signed-off-by: Milan Stevanovic <milan.o.stevanovic@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Drivers should not 'select' a subsystem. Instead they should depend
on it. If the subsystem is disabled, the user probably did that for
a purpose and one driver shouldn't be changing that.
This also makes all IIO drivers consistent w.r.t depending on SYSFS
instead of selecting it.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The X-Powers AXP813 PMIC is really close to what is already done for
AXP20X/AXP22X.
There are two pairs of bits to set the rate (one for Voltage and Current
measurements and one for TS/GPIO0 voltage measurements) instead of one.
The register to set the ADC rates is different from the one for
AXP20X/AXP22X.
GPIO0 can be used as an ADC (measuring Volts) unlike for AXP22X.
The scales to apply to the different inputs are unlike the ones from
AXP20X and AXP22X.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
To prepare for a future patch that will add a DT node for the ADC, make
axp20x_adc able to probe from DT and get the per-variant data from
of_device_id.data since platform_device_id.driver_data won't be set when
probing by DT.
Leave the ability to probe via platform for driver compatibility with
old DTs.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
To prepare for a new comer that set a different register with different
values, move rate setting in a function that is specific to each AXP
variant.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove unneeded error handling on the result of a call
to platform_get_resource() when the value is passed to
devm_ioremap_resource().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove unnecessary unaligned access routine in hts221_read_oneshot() and
the related include
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Introduce regmap API support to access to i2c/spi bus instead of
using a custom support.
Remove lock mutex since concurrency is already managed by regmap API
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove following sparse warnings in hts221_parse_temp_caldata() and in
hts221_parse_rh_caldata():
drivers/iio/humidity/hts221_core.c:302:19: warning: cast to
restricted __le16
drivers/iio/humidity/hts221_core.c:314:18: warning: cast to
restricted __le16
drivers/iio/humidity/hts221_core.c:320:18: warning: cast to
restricted __le16
drivers/iio/humidity/hts221_core.c:355:18: warning: cast to
restricted __le16
drivers/iio/humidity/hts221_core.c:361:18: warning: cast to
restricted __le16
Fixes: e4a70e3e7d ("iio: humidity: add support to hts221 rh/temp combo device")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
gcc-8 reports
drivers/iio/accel/st_accel_i2c.c: In function 'st_accel_i2c_probe':
./include/linux/string.h:245:9: warning: '__builtin_strncpy' specified
bound 20 equals destination size [-Wstringop-truncation]
The compiler require that the length of the dest string is greater than
the length we want to copy to make sure the dest string is
nul-terminated. We can just use strlcpy() to avoid this warning.
Signed-off-by: Xiongfeng Wang <xiongfeng.wang@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Error handling in stm32h7_adc_enable routine doesn't unwind enable
sequence correctly. ADEN can only be cleared by hardware (e.g. by
writing one to ADDIS).
It's also better to clear ADRDY just after it's been set by hardware.
Fixes: 95e339b6e8 ("iio: adc: stm32: add support for STM32H7")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
iio_priv does not return an error pointer, so check is not valid.
Patch suppresses it.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use of_device_get_match_data to optimize the source code.
No check is needed on dev_data as match table is defined in driver.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The labels and branching order of the error path of 'aspeed_adc_probe()'
are broken.
Re-order the labels and goto statements.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In case of error, the function devm_iio_device_alloc() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Fixes: e2e6771c64 ("IIO: ADC: add STM32 DFSDM sigma delta ADC support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Building with CONFIG_OF disabled produces a compiler warning:
drivers/iio/adc/stm32-dfsdm-core.c: In function 'stm32_dfsdm_probe':
drivers/iio/adc/stm32-dfsdm-core.c:245:22: error: unused variable 'pnode' [-Werror=unused-variable]
This removes the variable and open-codes it in the only place
it gets used to avoid that warning.
Fixes: bed73904e7 ("IIO: ADC: add stm32 DFSDM core support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add iio consumer API to set buffer size and watermark according
to sysfs API.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This code offers a way to handle PDM audio microphones in
ASOC framework. Audio driver should use consumer API.
A specific management is implemented for DMA, with a
callback, to allows to handle audio buffers efficiently.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add DFSDM driver to handle sigma delta ADC.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add driver for stm32 DFSDM pheripheral. Its converts a sigma delta
stream in n bit samples through a low pass filter and an integrator.
stm32-dfsdm-core driver is the core part supporting the filter
instances dedicated to sigma-delta ADC or audio PDM microphone purpose.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add generic driver to support sigma delta modulators.
Typically, this device is hardware connected to
an IIO device in charge of the conversion. Devices are
bonded through the hardware consumer API.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Extend the inkern API with functions for reading and writing
attribute of iio channels.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add devm_iio_hw_consumer_alloc function that calls iio_hw_consumer_free
when the device is unbound from the bus.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Hardware consumer interface can be used when one IIO device has
a direct connection to another device in hardware.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
in_concentration_raw should report, according to sysfs-bus-iio documentation,
a "Raw (unscaled no offset etc.) percentage reading of a substance."
Modify scale to convert from ppm/ppb to percentage:
1 ppm = 0.0001%
1 ppb = 0.0000001%
There is no offset needed to convert the ppm/ppb to percentage,
so remove offset from IIO_CONCENTRATION (IIO_MOD_CO2) channel.
Cc'd stable to reduce chance of userspace breakage in the long
run as we fix this wrong bit of ABI usage.
Signed-off-by: Narcisa Ana Maria Vasile <narcisaanamaria12@gmail.com>
Cc: <Stable@vger.kernel.org>
Reviewed-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use DEFINE_DEBUGFS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTRIBUTE
for debugfs files.
Semantic patch information:
Rationale: DEFINE_SIMPLE_ATTRIBUTE + debugfs_create_file()
imposes some significant overhead as compared to
DEFINE_DEBUGFS_ATTRIBUTE + debugfs_create_file_unsafe().
Generated by: scripts/coccinelle/api/debugfs/debugfs_simple_attr.cocci
Signed-off-by: Venkat Prashanth B U <venkat.prashanth2498@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use DEFINE_DEBUGFS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTRIBUTE
for debugfs files.
Semantic patch information:
Rationale: DEFINE_SIMPLE_ATTRIBUTE + debugfs_create_file()
imposes some significant overhead as compared to
DEFINE_DEBUGFS_ATTRIBUTE + debugfs_create_file_unsafe().
Generated by: scripts/coccinelle/api/debugfs/debugfs_simple_attr.cocci
Signed-off-by: Venkat Prashanth B U <venkat.prashanth2498@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove st_lsm6dsx_write_with_mask() declaration since it has been removed
in commit 6674bef628e6 ("iio: imu: st_lsm6dsx: add regmap API support")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allocate device read buffer at bootstrap and do not put it on the stack
since it is pretty big (~200B) and its size will increase adding support
to device hw timestamp.
Moreover this patch fixes following sparse warnings:
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c:250:17: warning: Variable length
array is used.
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c:283:55: error: cannot size
expression
Fixes: 290a6ce11d ("iio: imu: add support to lsm6dsx driver")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By default, watermark is set to '1'. Watermark is used to fine tune
cyclic dma buffer period. In case watermark is left untouched (e.g. 1)
and several channels are being scanned, buffer period is wrongly set
(e.g. to 1 sample). As a consequence, data is never pushed to upper layer.
Fix buffer period size, by taking scan channels number into account.
Fixes: 2763ea0585 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the patch to the file ti_am335x_adc.c
which fixes the following coccinelle warning:
WARNING: Comparison to bool
Signed-off-by: Venkat Prashanth B U <venkat.prashanth2498@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver creates a number of const structures that it stores in the
data field of an of_device_id array.
Add const to the declaration of the location that receives a value
from the data field to ensure that the compiler will continue to check
that the value is not modified and remove the const-dropping cast on
the access to the data field.
Done using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce regmap API support to access to i2c/spi bus instead of
using a custom support. Set max bulk read to
(32 / SAMPLE_SIZE) * SAMPLE_SIZE since spi_write_then_read() used in
regmap_spi indicates that is the max buffer length to use in order to
avoid a kmalloc for each bus access.
Remove lock mutex since concurrency is already managed by regmap API
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Apply le16_to_cpu() to data read from the sensor in order to take into
account architecture endianness
Fixes: 290a6ce11d (iio: imu: add support to lsm6dsx driver)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch affects BME280 and BMP280. The readout of the calibration
data is moved to the probe function. Each sensor data access triggered
reading the full calibration data before this patch. According to the
datasheet, Section 4.4.2., the calibration data is stored in non-volatile
memory.
Since the calibration data does not change, and cannot be changed by the
user, we can reduce bus traffic by reading the calibration data once.
Additionally, proper organization of the data types enables removing
some odd casts in the compensation formulas.
Signed-off-by: Stefan Tatschner <stefan.tatschner@gmail.com>
Tested-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the registers are read out once per conversion interval. If
the reading is delayed as the conversion has not yet finished, this extra
time is treated as being part of the readout, although it should delay
the start of the poll interval. This results in the interval starting
slightly earlier in each iteration, until all time between reads is
spent polling the status registers instead of sleeping.
To fix this, the delay has to account for the state of the conversion
ready flag. Whenever the conversion is already finished, schedule the next
read on the regular interval, otherwise schedule it one interval after the
flag bit has been set.
Split the work function in two functions, one for the status poll and one
for reading the values, to be able to note down the time when the flag
bit is raised.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the timestamp is no longer (ab-)used to measure the function run time,
it can be taken at the correct time, i.e. when the conversion has finished.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The iio timestamp clock is user selectable and may be non-monotonic. Also,
only part of the acquisition time is measured, thus the delay was longer
than intended.
Use a monotonic timestamp to track the time for the next poll iteration.
The timestamp is advanced by the sampling interval each iteration. In case
the conversion overrruns the register readout (i.e. fast sampling combined
with a slow bus), one or multiple samples will be dropped.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calibration register is used for calculating current register in
hardware according to datasheet:
current = shunt_volt * calib_register / 2048 (ina 226)
current = shunt_volt * calib_register / 4096 (ina 219)
Fix calib_register value to 2048 for ina226 and 4096 for ina 219 in
order to avoid truncation error and provide best precision allowed
by shunt_voltage measurement. Make current scale value follow changes
of shunt_resistor from sysfs as calib_register value is now fixed.
Power_lsb value should also follow shunt_resistor changes as stated in
datasheet:
power_lsb = 25 * current_lsb (ina 226)
power_lsb = 20 * current_lsb (ina 219)
This is a part of the patchset: https://lkml.org/lkml/2017/11/22/394
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Reviewed-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a patch to the at91_adc.c file that fixes up a brace
warning found by the checkpatch.pl tool
Signed-off-by: Venkat Prashanth B U <venkat.prashanth2498@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return value in hx711_reset() should indicate status of dout otherwise the
calling function is reporting an error as false positive
If there are two reads too close to each other, then the second one will
never succeed. This happens especially when using buffered mode with both
channels enabled.
When changing the channel on every trigger event the former 100 ms are not
enough for waiting until the device indicates normal mode.
Wait up to 1 second until the device turns into normal mode.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add buffer to device data struct and add trigger function
Data format is quite simple:
voltage - channel 0 32 Bit
voltage - channel 1 32 Bit
timestamp 64 Bit
Using both channels at the same time is working quite slow because of
changing the channel which needs a dummy read.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The conversion time can be up to 16 seconds (8 ms per channel, 2 channels,
1024 times averaging).
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although the datasheet states the CNVR flag is cleared by reading the
BUS_VOLTAGE register, it is actually cleared by reading any of the
voltage/current/power registers.
The behaviour has been confirmed by TI support:
http://e2e.ti.com/support/amplifiers/current-shunt-monitors/f/931/p/647053/2378282
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The timestamp is inserted into the buffer after the sample data by
iio_push_to_buffers_with_timestamp, document the space requirement for
the timestamp.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
iio_push_to_buffers_with_timestamp expects a void pointer, so the cast
is both unnecessary and misleading.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some Meson8 devices the channel muxes are not programmed. This
results in garbage values when trying to read channels that are not set
up.
Fix this by initializing the channel 0 and 1 muxes in
MESON_SAR_ADC_CHAN_10_SW as well as the muxes for all other channels in
MESON_SAR_ADC_AUX_SW based on what the vendor driver does (which is
simply a 1:1 mapping of channel number and channel mux).
This only showed up on Meson8 devices, because for GXBB and newer BL30
is taking care of initializing the channel muxes.
This additionally fixes a typo in the
MESON_SAR_ADC_AUX_SW_MUX_SEL_CHAN_MASK macro because the old definition
assumed that the register fields were 2 bit wide, while they are
actually 3 bit wide.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GX SoCs use a 1.2 MHz ADC clock, while the older SoCs use a 1.14 MHz
clock.
A comment in the driver from Amlogic's GPL kernel says that it's
running at 1.28 MHz. However, it's actually programming a divider of
20 + 1. With a XTAL clock of 24 MHz this results in a frequency of
1.14 MHz. (their calculation might be based on a 27 MHz XTAL clock,
but this is not what we have on the Meson8 and Meson8b SoCs).
The ADC was still working with the 1.2MHz clock. In my own tests I did
not see a difference between 1.2 and 1.14 MHz (regardless of the clock
frequency used, the ADC results were identical).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These duplicate includes have been found with scripts/checkincludes.pl but
they have been removed manually to avoid removing false positives.
Signed-off-by: Pravin Shedge <pravin.shedge4linux@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Found with scripts/coccinelle/misc/boolconv.cocci.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Structures st_uvis25_i2c_regmap_config and st_uvis25_spi_regmap_config are
local to the source and do not need to be in global scope, so make them
both static.
Cleans up sparse warnings:
warning: symbol 'st_uvis25_i2c_regmap_config' was not declared. Should
it be static?
warning: symbol 'st_uvis25_spi_regmap_config' was not declared. Should
it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a sysfs attribute that exposes buffer data available to userspace.
This attribute can be checked at runtime to determine the overall buffer
fill level (across all allocated buffers).
Signed-off-by: Matt Fornero <matt.fornero@mathworks.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This replaces the custom license information text with the appropriate
SPDX identifier. While the information here stays the same, it is easier
to read.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Harinath Nampally <harinath922@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
getnstimeofday() suffers from the overflow in y2038 on 32-bit
architectures and requires a conversion into the nanosecond format that
we want here.
This changes ssp_parse_dataframe() to use ktime_get_real_ns() directly,
which does not have that problem.
An open question is what time base should be used here. Normally
timestamps should use ktime_get_ns() or ktime_get_boot_ns() to read
monotonic time instead of "real" time, which suffers from time jumps
due to settimeofday() calls or leap seconds.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As discussed with Marc Zyngier: irq_sim_init() and its devres variant
should return the base of the allocated interrupt range on success
rather than 0. This will be modified later - first, change the way
users handle the return value of these routines.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves the merge issue pointed out by Stephen in
drivers/iio/adc/meson_saradc.c.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GPIO core provides a handy GPIO_LOOKUP() macro to populate a struct
gpiod_lookup array without having to spell out attribute names (but
still avoid breakage when attributes within the struct are rearranged
or added).
The axp288_adc.c driver uses a similar macro to populate a struct
iio_map array. Make it available to others.
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
The I2C device ID table entries have the .driver_data field set, but they
are not used in the driver so weren't set in the OF device table entries.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The "sana" clock is not used at SAR ADC module in Amlogic Meson SoC,
it is irrelevant for the SAR ADC.
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As per ABI temperature should be in milli Celsius after scaling,
not Celsius
Note on stable cc. This driver is breaking the standard IIO
ABI. (JC)
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix build errors in kernel-doc notation. Symbols that end in '_'
have a special meaning, but adding a '*' makes them OK.
../drivers/iio/industrialio-core.c:635: ERROR: Unknown target name: "iio_val".
../drivers/iio/industrialio-core.c:642: ERROR: Unknown target name: "iio_val".
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The Meson GXBB and newer SoCs have a few more registers than the older
Meson8 and Meson8b SoCs.
Use a separate regmap config to limit the older SoCs to the DELTA_10
register.
Fixes: 6c76ed31cd ("iio: adc: meson-saradc: add Meson8b SoC compatibility")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Meson8 and Meson8b do not have the MESON_SAR_ADC_REG11 register. The
bandgap setting for these SoCs is configured in the
MESON_SAR_ADC_DELTA_10 register instead.
Make the driver aware of this difference and use the correct bandgap
register depending on the SoC.
This has worked fine on Meson8 and Meson8b because the bootloader is
already initializing the bandgap setting.
Fixes: 6c76ed31cd ("iio: adc: meson-saradc: add Meson8b SoC compatibility")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Meson8 and Meson8b SoCs use the the SAR ADC gate clock provided by the
MESON_SAR_ADC_REG3 register within the SAR ADC register area.
According to the datasheet (and the existing MESON_SAR_ADC_REG3_CLK_EN
definition) the gate is on bit 30.
The fls() function returns the last set bit, which is "bit index + 1"
(fls(MESON_SAR_ADC_REG3_CLK_EN) returns 31). Fix this by switching to
__ffs() which returns the first set bit, which is bit 30 in our case.
This off by one error results in the ADC not being usable on devices
where the bootloader did not enable the clock.
Fixes: 3adbf34273 ("iio: adc: add a driver for the SAR ADC found in Amlogic Meson SoCs")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The commit 0f0796509c
("iio: remove gpio interrupt probing from drivers that use a single interrupt")
removed custom IRQ assignment for the drivers which are enumerated via
ACPI or OF. Unfortunately, some ACPI tables have IRQ line defined as
GpioIo() resource and thus automatic IRQ allocation will fail.
Partially revert the commit 0f0796509c to restore original behaviour.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Function platform_get_irq_byname() returns a negative error code on
failure, and a zero or positive number on success. However, in function
cpcap_adc_probe(), positive IRQ numbers are also taken as error cases.
Use "if (ddata->irq < 0)" instead of "if (!ddata->irq)" to validate the
return value of platform_get_irq_byname().
Signed-off-by: Pan Bian <bianpan2016@163.com>
Fixes: 25ec249632 ("iio: adc: cpcap: Add minimal support for CPCAP PMIC ADC")
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Pointer pdata is being assigned but it is never being used, hence
it is redundant and can be removed. Cleans up clang warning:
drivers/iio/accel/st_accel_core.c:952:3: warning: Value stored to 'pdata'
is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This adds an ACPI table to the driver and the ACPI ID of the sensor
on the tablet.
Signed-off-by: Luke Ross <luke@lukeross.name>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
add support for STMicroelectronics UVIS25 uv sensor
http://www.st.com/resource/en/datasheet/uvis25.pdf
- continuos mode support
- i2c support
- spi support
- trigger mode support
- system PM support
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ASPEED SoC must deassert a reset in order to use the ADC peripheral.
The device tree bindings are updated to document the resets phandle, and
the example is updated to match what is expected for both the reset and
clock phandle. Note that the bindings should have always had the reset
controller, as the hardware is unusable without it.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The Maxim MAX30105 part adds a third LED (green) and uses a multi-LED
measuring mode producing three measurements
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Current code assumes always 2 measurements (6 bytes) have to be copied,
prepare for more flexibility
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move the programming of the mode setting from init() to
buffer_postenable()
Split out a separate function to
only update the power/shutdown bit
This changes permits to more easily implement different
modes of measurements in further patches
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Chip must not be in shutdown for reading temperature, so briefly leave
shutdown if buffer is not already running
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Peter Meerwald-Stalder <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Table 4 of the datasheet specifies the mode control, these are not
individual bits; add multi LED mode
Add multi-LED mode and fix MODE_MASK (3 bits wide, not 2)
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
STM32H7 ADC channels can be configured either as single ended or
differential with 'st,adc-channels' or 'st,adc-diff-channels'
(positive and negative input pair: <vinp vinn>, ...).
Differential channels have different offset and scale, from spec:
raw value = (full_scale / 2) * (1 + (vinp - vinn) / vref).
Add offset attribute.
Differential channels are selected by DIFSEL register. Negative
inputs must be added to pre-selected channels as well (PCSEL).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove const array that defines channels. Build channels definition
at probe time, when initializing channels (only for requested ones).
This will ease adding differential channels support.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reducing shunt and bus voltage range improves the accuracy, so allow
altering the default settings.
Both settings are exposed as gain values. While for the shunt voltage
this is straightforward, the bus range settings of 32V (default) and 16V
are mapped to gain values of 1 resp. 2, to provide a uniform API to
userspace.
As the gain settings are incorporated into the raw values by the sensor
itself, adjusting of the scale attributes is not necessary.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
While the config uses the physical value corresponding to the LSB
for both the power and the bus voltage register, the shunt voltage is
specified as parts of 1 mV. Use the LSB physical value for all registers.
No functional change.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Lower bits of the INA219/220 bus voltage register are conversion
status flags, properly shift the value.
When reading via IIO buffer, the value is passed on unaltered,
shifting is the responsibility of the user.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since i2c_unregister_device() became NULL-aware we may remove duplicate
NULL check.
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add new ACPI ID for ak9911 as had been found on prototype board.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add new ACPI ID for sx9500 as had been found on prototype board.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Rename structs holding event configuration registers
to more appropriate names. This naming is consistent
with the event config register names given in the
mma845x and fxls8471 datasheets.
Signed-off-by: Harinath Nampally <harinath922@gmail.com>
Acked-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Rename time step look up struct to generic name
as the values in the look table are same for all
the other events like pulse, transient etc.
Signed-off-by: Harinath Nampally <harinath922@gmail.com>
Acked-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Driver for 20-bit ALS and UV B sensor with I2C interface exposing
the following API:
in_uvindex_input
in_illuminance_raw
in_illuminance_scale
in_illuminance_scale_available
in_intensity_uv_raw
in_intensity_uv_scale
in_intensity_uv_scale_available
integration_time
integration_time_available
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1397962
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix gcc warnings about variable 'ec_device' being set but not used
in these files:
common/cros_ec_sensors/cros_ec_sensors.c:194:25
light/cros_ec_light_prox.c:184:25
Signed-off-by: Paolo Cretaro <paolocretaro@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Need to acknowledge DRDY irq in direct mode/ software
triggered mode. Otherwise, on the next conversion, overrun
flag will be raised, which is not a correct state.
This doesn't affect the functionality, but will generate
possible incorrect overrun reports.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Added support for DMA transfers. The implementation uses the user watermark
to decide whether DMA will be used or not. For watermark 1, DMA will not be
used. If watermark is bigger, DMA will be used.
Sysfs attributes are created to indicate whether the DMA is used,
with hwfifo_enabled, and the current DMA watermark is readable
in hwfifo_watermark. Minimum and maximum values are in hwfifo_watermark_min
and hwfifo_watermark_max.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The module license checker complains about these two so just fix
it up. They are both GPLv2, both written by me or using code
I extracted while refactoring from the GPLv2 drivers.
Cc: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
- proper use of the bool type (Thomas Meyer)
- constification of struct config_item_type (Bhumika Goyal)
-----BEGIN PGP SIGNATURE-----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=+tMO
-----END PGP SIGNATURE-----
Merge tag 'configfs-for-4.15' of git://git.infradead.org/users/hch/configfs
Pull configfs updates from Christoph Hellwig:
"A couple of configfs cleanups:
- proper use of the bool type (Thomas Meyer)
- constification of struct config_item_type (Bhumika Goyal)"
* tag 'configfs-for-4.15' of git://git.infradead.org/users/hch/configfs:
RDMA/cma: make config_item_type const
stm class: make config_item_type const
ACPI: configfs: make config_item_type const
nvmet: make config_item_type const
usb: gadget: configfs: make config_item_type const
PCI: endpoint: make config_item_type const
iio: make function argument and some structures const
usb: gadget: make config_item_type structures const
dlm: make config_item_type const
netconsole: make config_item_type const
nullb: make config_item_type const
ocfs2/cluster: make config_item_type const
target: make config_item_type const
configfs: make ci_type field, some pointers and function arguments const
configfs: make config_item_type const
configfs: Fix bool initialization/comparison
Here is the "big" staging and IIO driver update for 4.15-rc1.
Lots and lots of little changes, almost all minor code cleanups as the
Outreachy application process happened during this development cycle.
Also happened was a lot of IIO driver activity, and the typec USB code
moving out of staging to drivers/usb (same commits are in the USB tree
on a persistent branch to not cause merge issues.)
Overall, it's a wash, I think we added a few hundred more lines than
removed, but really only a few thousand were modified at all.
All of these have been in linux-next for a while. There might be a
merge issue with Al's vfs tree in the pi433 driver (take his changes,
they are always better), and the media tree with some of the odd atomisp
cleanups (take the media tree's version).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgnFrg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymxbwCgtNlBkqD2JJYpLRKvI/C4w1vzZsEAnA2THRkt
g3ioPBqmqC/2DSbldr2o
=/ebw
-----END PGP SIGNATURE-----
Merge tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO updates from Greg KH:
"Here is the "big" staging and IIO driver update for 4.15-rc1.
Lots and lots of little changes, almost all minor code cleanups as the
Outreachy application process happened during this development cycle.
Also happened was a lot of IIO driver activity, and the typec USB code
moving out of staging to drivers/usb (same commits are in the USB tree
on a persistent branch to not cause merge issues.)
Overall, it's a wash, I think we added a few hundred more lines than
removed, but really only a few thousand were modified at all.
All of these have been in linux-next for a while. There might be a
merge issue with Al's vfs tree in the pi433 driver (take his changes,
they are always better), and the media tree with some of the odd
atomisp cleanups (take the media tree's version)"
* tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (507 commits)
staging: lustre: add SPDX identifiers to all lustre files
staging: greybus: Remove redundant license text
staging: greybus: add SPDX identifiers to all greybus driver files
staging: ccree: simplify ioread/iowrite
staging: ccree: simplify registers access
staging: ccree: simplify error handling logic
staging: ccree: remove dead code
staging: ccree: handle limiting of DMA masks
staging: ccree: copy IV to DMAable memory
staging: fbtft: remove redundant initialization of buf
staging: sm750fb: Fix parameter mistake in poke32
staging: wilc1000: Fix bssid buffer offset in Txq
staging: fbtft: fb_ssd1331: fix mirrored display
staging: android: Fix checkpatch.pl error
staging: greybus: loopback: convert loopback to use generic async operations
staging: greybus: operation: add private data with get/set accessors
staging: greybus: loopback: Fix iteration count on async path
staging: greybus: loopback: Hold per-connection mutex across operations
staging: greybus/loopback: use ktime_get() for time intervals
staging: fsl-dpaa2/eth: Extra headroom in RX buffers
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New device support
* ti-dac082s085 dac
- new driver supporting 8, 10 and 12 bit TI DACs with 2 and 4 channels:
DAC082S085, DAC102S085, DAC122S085, DAC104s085 and DAC124S085.
Minor features and cleanps
* adc12138
- make array ch_to_mux static for small object code size reduction.
* sun4i-gpadc
- use of_device_get_match_data rather than opencoding it.
* stm32 trigger
- add tim15 tigger on STM32H7
- check clock rate to avoid potential division by zero
* tsl2x7x staging cleanups.
- move *_thresh_period to being created by IIO core.
- remove unused tsl2x7x_parse_result structure.
- sort includes
- drop a repeat iio_dev forward definition
- fix some code alignment of defines.
- use IIO_CONST_ATTR for constant string attribute
- drop some unnecessary parentheses
- fix various alignment with parenthese
- rename power defines for readability reasons
- fix a missaligned break statement
- Tidy up function definitions so they fit on a single line.
-----BEGIN PGP SIGNATURE-----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=IXO+
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.15c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Third set of new device support, cleanups and features for IIO in the 4.15 cycle
New device support
* ti-dac082s085 dac
- new driver supporting 8, 10 and 12 bit TI DACs with 2 and 4 channels:
DAC082S085, DAC102S085, DAC122S085, DAC104s085 and DAC124S085.
Minor features and cleanps
* adc12138
- make array ch_to_mux static for small object code size reduction.
* sun4i-gpadc
- use of_device_get_match_data rather than opencoding it.
* stm32 trigger
- add tim15 tigger on STM32H7
- check clock rate to avoid potential division by zero
* tsl2x7x staging cleanups.
- move *_thresh_period to being created by IIO core.
- remove unused tsl2x7x_parse_result structure.
- sort includes
- drop a repeat iio_dev forward definition
- fix some code alignment of defines.
- use IIO_CONST_ATTR for constant string attribute
- drop some unnecessary parentheses
- fix various alignment with parenthese
- rename power defines for readability reasons
- fix a missaligned break statement
- Tidy up function definitions so they fit on a single line.
The two properties unique to each supported chip, resolution and number
of channels, are currently gleaned from the chip's name.
E.g. dac102s085 is a dual channel 10-bit DAC.
^^^
This was deemed unmaintainable by the subsystem maintainer once the
driver is extended to support further chips, hence it was requested
to add an explicit table for chip-specific information and use an
enum to reference into it.
This adds 17 LoC without any immediate gain, so make the change in a
separate commit which can be reverted if we determine in 10 years that
it was unnecessary.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The DACrrcS085 (rr = 08/10/12, c = 2/4) family of SPI DACs was
inherited by TI when they acquired National Semiconductor in 2011.
This driver was developed for and tested with the DAC082S085 built into
the Revolution Pi by KUNBUS, but should work with any of the other
chips as they share the same programming interface.
There is also a family of I2C DACs with just a single channel called
DACrr1C08x (rr = 08/10/12, x = 1/5). Their programming interface is
very similar and it should be possible to extend the driver for these
chips with moderate effort. Alternatively they could be integrated into
ad5446.c. (The AD5301/AD5311/AD5321 use different power-down modes but
otherwise appear to be comparable.)
Furthermore there is a family of 8-channel DACs called DACrr8S085
(rr = 08/10/12) as well as two 16-bit DACs called DAC161Sxxx
(xxx = 055/997). These are more complicated devices with support for
daisy-chaining and the ability to power down each channel separately.
They could either be handled by a separate driver or integrated into the
present driver with a larger effort.
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The usage of of_device_get_match_data reduce the code size a bit.
Furthermore, it prevents an improbable dereference when
of_match_device() return NULL.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Don't populate const array ch_to_mux on the stack, instead
make it static. Makes the object code smaller by over 200 bytes:
Before:
text data bss dec hex filename
12663 1648 128 14439 3867 drivers/iio/adc/ti-adc12138.o
After
text data bss dec hex filename
12353 1744 128 14225 3791 drivers/iio/adc/ti-adc12138.o
(gcc version 7.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add check on STM32 ADC clock rate to report an explicit error.
This may avoid division by 0 later in stm32-adc driver.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add TIM15_TRGO trigger that is now supported on STM32H7.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make the argument of the functions iio_sw{d/t}_group_init_type_name const
as they are only passed to the function config_group_init_type_name having
the argument as const.
Make the config_item_type structures const as they are either passed to
the functions having the argument as const or they are
stored in the const "ci_type" field of a config_item structure.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@Huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add driver to support older EC firmware that only support deprecated
ec command. Rely on ACPI memory map register to access sensor
information.
Present same interface as the regular cros_ec sensor stack:
- one iio device per accelerometer
- use HTML5 axis definition
- use iio abi units
- accept calibration calls, but do nothing
Chrome can use the same code than regular cros_ec sensor stack to
calculate orientation and lid angle.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This fix allows platforms to probe correctly even if the
trigger edge property is missing. The hardware trigger
will no longer be registered in the sybsystem
Preserves backwards compatibility with the support that
was in the driver before the hardware trigger.
https://storage.kernelci.org/mainline/master/v4.14-rc2-255-g74d83ec2b734/arm/sama5_defconfig/lab-free-electrons/boot-at91-sama5d2_xplained.txt
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Fixes: 5e1a1da0f ("iio: adc: at91-sama5d2_adc: add hw trigger and buffer support")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
One of the user complained that on his system Thinkpad Yoga S1, with
commit f1664eaace ("iio: hid-sensor-trigger: Fix the race with user
space powering up sensors") causes the system to resume immediately
on suspend (S3 operation). On this system the sensor hub is on USB
and is a wake up device from S3. So if any sensor sends data on
motion, the system will wake up. This can be a legitimate use case
to wake up device motion, but that needs proper user space support
to set right thresholds.
In fact the above commit didn't cause this regression, but any operation
which cause sensors to wake up would have caused the same issue. So if
user reads the raw sensor data, same issue occurs, with or without this
commit. Only difference is that the above commit by default will trigger
a power up and power down of sensors as part of runtime pm enable
(runtime enable will cause a runtime resume callback followed by
runtime_suspend callback). Previously user has to do some action on
sensors.
On investigation it was observed that the current driver correctly
changing the state of all sensors to power off but then also some sensor
will still send some data. Only option is to never power up any sensor.
Only good option is to:
- Using sysfs interface disable USB as a wakeup device (This will not
need any driver change)
Since some user don't care about sensors. So for those users this change
brings back old functionality. As long as they don't cause any operation
to power up sensors (like raw read or start iio-sensor-proxy service),
the sensors will not be to touched. This is done by delaying run time
enable till user space does some operation with sensors.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=196853
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Driver for RF Digital RFD77402 VCSEL (vertical-cavity surface-emitting
laser) Time-of-Flight (ToF) sensor to measure distance up to 2 m with
millimeter precision
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
add support to STMicroelectronics LIS3DHH accel sensor
http://www.st.com/resource/en/datasheet/lis3dhh.pdf
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Do not try to configure sample frequency if the sensor do not export
odr register address in register map. That change will be used to
properly support LIS3DHH accel sensor.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Define st_sensor_int_drdy structure in st_sensor_data_ready_irq in order
to contain irq line parameters of the device.
Moreover separate data-ready open-drain configuration parameters for INT1
and INT2 pins in st_sensor_data_ready_irq data structure.
That change will be used to properly support LIS3DHH accel sensor.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add SPI Serial Interface Mode (SIM) register information
to STM pressure framework
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add SPI Serial Interface Mode (SIM) register information to
LIS3MDL magn sensor
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add SPI Serial Interface Mode (SIM) register information
to STM gyroscope framework
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
add support to STMicroelectronics LIS2DW12 accelerometer in
st_accel framework
http://www.st.com/resource/en/datasheet/lis2dw12.pdf
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
New devices (e.g. LIS2DW12) enable all axis by default and do not export
that capability in register map. Check if the enable_axis register
address has been declared in st_sensor_settings map in order to verify if
the driver needs to enable all sensor axis
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fabrice Gasnier