The full name of PSR is Panel Self Refresh, panel device could refresh
itself with the hardware framebuffer in panel, this would make lots of
sense to save the power consumption.
This patch have exported two symbols for platform driver to implement
the PSR function in hardware side:
- analogix_dp_active_psr()
- analogix_dp_inactive_psr()
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
It's better to pass the connector to platform driver in .get_modes()
callback, just like what the .get_modes() helper function designed.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Tomasz Figa <tomasz.figa@chromium.com>
RK3399 and RK3288 shared the same eDP IP controller, only some light
difference with VOP configure and GRF configure.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Tomasz Figa <tomasz.figa@chromium.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
As vendor document indicate, when REF_CLK bit set 0, then DP
phy's REF_CLK should switch to 24M source clock.
But due to IC PHY layout mistaken, some chips need to flip this
bit(like RK3288), and unfortunately they didn't indicate in the
DP version register. That's why we have to make this little hack.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Tomasz Figa <tomasz.figa@chromium.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Rockchip have three clocks for dp controller, we leave pclk_edp
to analogix_dp driver control, and keep the sclk_edp_24m and
sclk_edp in platform driver.
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Split the dp core driver from exynos directory to bridge directory,
and rename the core driver to analogix_dp_*, rename the platform
code to exynos_dp.
Beside the new analogix_dp driver would export six hooks.
"analogix_dp_bind()" and "analogix_dp_unbind()"
"analogix_dp_suspned()" and "analogix_dp_resume()"
"analogix_dp_detect()" and "analogix_dp_get_modes()"
The bind/unbind symbols is used for analogix platform driver to connect
with analogix_dp core driver. And the detect/get_modes is used for analogix
platform driver to init the connector.
They reason why connector need register in helper driver is rockchip drm
haven't implement the atomic API, but Exynos drm have implement it, so
there would need two different connector helper functions, that's why we
leave the connector register in helper driver.
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Here are some development updates for the Synopsis Designware HDMI driver,
which clean up some of the code, and start preparing to add audio support
to the driver. This series of patches are based on a couple of dependent
commits from the ALSA tree.
Briefly, the updates are:
- move comments which should have moved with the phy values to the IMX
part of the driver.
- clean up the phy configuration: to all lookups before starting to
program the phy.
- clean up the HDMI clock regenerator code
- use the drm_hdmi_avi_infoframe_from_display_mode() helper which allows
the code to be subsequently simplified
- remove the unused 'regmap' pointer in struct dw_hdmi
- use the bridge drm device rather than the connector (we're the bridge
code)
- remove private hsync/vsync/interlaced flags, getting them from the
DRM mode structure instead.
- implement interface functions to support audio - setting the audio
sample rate, and enabling the audio clocks.
- removal of broken pixel repetition support
- cleanup DVI vs HDMI sink handling
- enable audio only if connected device supports audio
- avoid double-enabling bridge in the sink path (once in mode_set, and
again in commit)
- rename mis-named dw_hdmi_phy_enable_power()
- fix bridge enable/disable handing, so a plug-in event doesn't
reconfigure the bridge if DRM has disabled the output
- fix from Vladimir Zapolskiy for the I2CM_ADDRESS macro name
These are primerily preparitory patches for the AHB audio driver and
the I2S audio driver (from Rockchip) for this IP.
* 'drm-dwhdmi-devel' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
drm: bridge/dw_hdmi: fix register I2CM_ADDRESS register name
drm: bridge/dw_hdmi: fix phy enable/disable handling
drm: bridge/dw_hdmi: rename dw_hdmi_phy_enable_power()
drm: bridge/dw_hdmi: avoid enabling interface in mode_set
drm: bridge/dw_hdmi: enable audio only if sink supports audio
drm: bridge/dw_hdmi: clean up HDMI vs DVI mode handling
drm: bridge/dw_hdmi: don't support any pixel doubled modes
drm: bridge/dw_hdmi: remove pixel repetition setting for all VICs
drm: bridge/dw_hdmi: introduce interfaces to enable and disable audio
drm: bridge/dw_hdmi: introduce interface to setting sample rate
drm: bridge/dw_hdmi: remove mhsyncpolarity/mvsyncpolarity/minterlaced
drm: bridge/dw_hdmi: use our own drm_device
drm: bridge/dw_hdmi: remove unused 'regmap' struct member
drm: bridge/dw_hdmi: simplify hdmi_config_AVI() a little
drm: bridge/dw_hdmi: use drm_hdmi_avi_infoframe_from_display_mode()
drm: bridge/dw_hdmi: clean up hdmi_set_clk_regenerator()
drm: bridge/dw_hdmi: clean up phy configuration
drm: imx/dw_hdmi: move phy comments
drm/edid: add function to help find SADs
iMX6 devices suffer from an errata (ERR005174) where the audio FIFO can
be emptied while it is partially full, resulting in misalignment of the
audio samples.
To prevent this, the errata workaround recommends writing N as zero
until the audio FIFO has been loaded by DMA. Writing N=0 prevents the
HDMI bridge from reading from the audio FIFO, effectively disabling
audio.
This means we need to provide the audio driver with a pair of functions
to enable/disable audio. These are dw_hdmi_audio_enable() and
dw_hdmi_audio_disable().
A spinlock is introduced to ensure that setting the CTS/N values can't
race, ensuring that the audio driver calling the enable/disable
functions (which are called in an atomic context) can't race with a
modeset.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Introduce dw_hdmi_set_sample_rate(), which allows us to configure the
audio sample rate, setting the CTS/N values appropriately.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This header file declares prototypes of functions that are no longer
used. Remove this file and all references to it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Because of iMX6 & Rockchip have differnet mpll config parameter,
the VLEVCTRL parameter would be different. In this case we should
separate VLEVCTRL setting from the common dw_hdmi driver, config
this parameter in platform driver(dw_hdmi-imx and dw_hdmi-rockchip)
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently, third party bridge drivers(ptn3460) are dependent
on the corresponding encoder driver init, since bridge driver
needs a drm_device pointer to finish drm initializations.
The encoder driver passes the drm_device pointer to the
bridge driver. Because of this dependency, third party drivers
like ptn3460 doesn't adhere to the driver model.
In this patch, we reframe the bridge registration framework
so that bridge initialization is split into 2 steps, and
bridge registration happens independent of drm flow:
--Step 1: gather all the bridge settings independent of drm and
add the bridge onto a global list of bridges.
--Step 2: when the encoder driver is probed, call drm_bridge_attach
for the corresponding bridge so that the bridge receives
drm_device pointer and continues with connector and other
drm initializations.
The old set of bridge helpers are removed, and a set of new helpers
are added to accomplish the 2 step initialization.
The bridge devices register themselves onto global list of bridges
when they get probed by calling "drm_bridge_add".
The parent encoder driver waits till the bridge is available
in the lookup table(by calling "of_drm_find_bridge") and then
continues with its initialization.
The encoder driver should also call "drm_bridge_attach" to pass
on the drm_device to the bridge object.
drm_bridge_attach inturn calls "bridge->funcs->attach" so that
bridge can continue with drm related initializations.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Rahul Sharma <rahul.sharma@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rockchip RK3288 hdmi is compatible with dw_hdmi
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
the original imx hdmi driver is under drm/imx/,
which depends on imx-drm, so move the imx hdmi
driver out to drm/bridge and rename it to dw_hdmi
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This patch adds a drm_bridge driver for the PTN3460 DisplayPort to LVDS
bridge chip.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Tomeu Vizoso