Whenever the reset work is queued up, do not generate beacon. And also
clear the beacon miss count once the beacon stuck was observed.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After the chip reset, the noise immunity levels are restored with
history values. If the immunity levels are lower than the defaults,
lets start with the optimal values.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sync-up ibss beacon timer with the beacon frame's timestamp. When the
node acts as joiner, it has to sync with the received beacon timestamp
instead of reading tsf from hw. As the hw tsf wont wont be update till
bssid is configured. This patch programs hw tsf with the received beacon
timestamp if beacon timers are yet to be configured.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update AR9462 initval to fix unbalance beacon distribution
in Ad-Hoc network.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver is allocating memory during initialization with GFP_ATOMIC
even though GFP_KERNEL is sufficient. This patch fixes it.
Signed-off-by: Matt Renzelmann <mjr@cs.wisc.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Last patch I sent failed to take into account the offset of each phy.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since it's only called when beacons are stuck, move it to the SWBA handler
tasklet, to avoid doing redundant checks on every single interrupt.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
LED support is typically handled via system GPIO on these platforms.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also tweak beacon response times for better stability with the shorter
timer intervals.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Following Felix's recent patchset as an example I have replaced memcmp with
compare_ether_addr.
"Because of the constant size and guaranteed 16 bit alignment, the inline
compare_ether_addr function is much cheaper than calling memcmp."
Signed-off-by: Jonathan Bither <jonbither@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Report all defined sync_cause errors in debugfs
to aid with debugging.
Use a macro to print out the interrupts file contents
to decrease code duplication.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This hides some repetitive code, and will help if the
column widths ever need to change.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 109d244605
"net/mlx4_en: Set max rate-limit for a TC"
introduced 64 bit math operations into mlx4_en_dcbnl_ieee_setmaxrate()
causing the following final link failure on an x86_32 allmodconfig
ERROR: "__udivdi3" [drivers/net/ethernet/mellanox/mlx4/mlx4_en.ko] undefined!
Convert it to use div_u64() instead.
Cc: Amir Vadai <amirv@mellanox.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/atheros/atlx/atl1.c
drivers/net/ethernet/atheros/atlx/atl1.h
Resolved a conflict between a DMA error bug fix and NAPI
support changes in the atl1 driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds FDB bridge ops to the macvlan device passthru mode.
Additionally a flags field was added and a NOPROMISC bit to
allow users to use passthru mode without the driver calling
dev_set_promiscuity(). The flags field is a u16 placed in a
4 byte hole (consuming 2 bytes) of the macvlan_dev struct.
We want to do this so that the macvlan driver or stack
above the macvlan driver does not have to process every
packet. For the use case where we know all the MAC addresses
of the endstations above us this works well.
This patch is a result of Roopa Prabhu's work. Follow up
patches are needed for VEPA and VEB macvlan modes.
v2: Change from distinct nopromisc mode to a flags field to
configure this. This avoids the tendency to add a new
mode every time we need some slightly different behavior.
v3: fix error in dev_set_promiscuity and add change and get
link attributes for flags.
CC: Roopa Prabhu <roprabhu@cisco.com>
CC: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UTA table was being set to the functional equivalent of promiscuous
mode. This was resulting in traffic from the virtual function being
flooded onto the wire and the PF device. This resulted in additional
overhead for VF traffic sent to the network and in the case of traffic
sent to the PF or another VF resulted in unwanted packets on the wire.
This was actually not the intended behavior. Now that we can program
the embedded switch correctly we can remove this snippit of code. Users
who want to support this should configure the FDB correctly using the
FDB ops.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows RAR table updates while in promiscuous. With
SR-IOV enabled it is valuable to allow the RAR table to
be updated even when in promisc mode to configure forwarding
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable FDB ops on ixgbe when in SR-IOV mode.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To prevent interrupts lost they should be dropped only if
they are scheduled via napi interfaces. In other case, there is
exists situation when napi handler process TX interrupt, stay in
RX processing and in that moment any other interrupt received.
Then before this patch TX bit in ISR will be cleaned, napi
schedule will not occur in case of currently processing event and
TX interrupt definitely will be lost.
Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the rx/tx handled inside napi handler, the cycle is
not needed now, because only the rx/tx need such kind of
processing.
Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unfortunately it is not clear from code is usage of
IMR register possible or not. So, to prevent possible
side-effects of reading this register i prefer store
interrupts enable flag separately.
Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function should be used later to set/remove proper
bits in imr to disable only rx ints.
Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like direct writes to IMR register is not good idea,
because there are exist functions to make this work.
Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the tx ints processing same as rx ones via napi.
The idea got from e1000. The interrupt disabling is
still not fine grained.
Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is first step, here there is no fine interrupt
disabling which cause TX/ERR interrupts stalling when
RX scheduled ints processed.
Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove rx from unlikely optimization in case of rx is very
likely thing for network card. This also reduce code a bit.
Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As hypervior does not have the knowledge of guest network configuration, it's
better to ask guest to send gratuitous packets when needed.
This patch implements VIRTIO_NET_F_GUEST_ANNOUNCE feature: hypervisor would
notice the guest when it thinks it's time for guest to announce the link
presnece. Guest tests VIRTIO_NET_S_ANNOUNCE bit during config change interrupt
and woule send gratuitous packets through netif_notify_peers() and ack the
notification through ctrl vq.
We need to make sure the atomicy of read and ack in guest otherwise we may ack
more times than being notified. This is done through handling the whole config
change interrupt in an non-reentrant workqueue.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the beginning of ks_rcv(), a for loop retrieves the
header information relevant to all the frames stored
in the mac's internal buffers. The number of pending
frames is stored as an 8 bits field in KS_RXFCTR.
If interrupts are disabled long enough to allow for more than
32 frames to accumulate in the MAC's internal buffers, a buffer
overflow occurs.
This patch fixes the problem by making the
driver's frame_head_info buffer big enough.
Well actually, since the chip appears to have 12K of
internal rx buffers and the shortest ethernet frame should
be 64 bytes long, maybe the limit could be set to
12*1024/64 = 192 frames, but 255 should be safer.
Signed-off-by: Davide Ciminaghi <ciminaghi@gnudd.com>
Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts the drivers in drivers/net/wan/* to use
module_pci_driver() macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts the drivers in drivers/net/tokenring/* to use
module_pci_driver() macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for I2C clock stretching which is required per
SFF-8636. Customers with passive DA cables implement clock stretching
would fail without this patch.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace occurrences of 'if (<bool expr> == <1|0>)' with
'if ([!]<bool expr>)'
Replace occurrences of '<bool var> = (<non-bool expr>) ? true : false'
with '<bool var> = <non-bool expr>'.
Replace occurrence of '<bool var> = <non-bool expr>' with
'<bool var> = !!<non-bool expr>'
While the latter replacement is not really necessary, it is done here for
consistency and clarity. No functional changes.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that split strings generate checkpatch warnings (per Chapter 2 of
Documentation/CodingStyle to make it easier to grep the code for the
string) cleanup the remaining instances of them in the driver.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables software (and phy device) transmit time stamping.
Tested on an old PIII laptop with built in NIC.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are times we turn of the laser before shutdown. This is a bad thing
if we want to wake on lan to work so now we make sure the laser is on
before shutdown if we support WoL.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A workaround was previously put in the driver to reset the device when
transitioning to Sx in order to activate the changed settings of the PHY
OEM bits (Low Power Link Up, or LPLU, and GbE disable configuration) for
82577/8/9 devices. After further review, it was found such a reset can
cause the 82579 to confuse which version of 82579 it actually is and broke
LPLU on all 82577/8/9 devices. The workaround during an S0->Sx transition
on 82579 (instead of resetting the PHY) is to restart auto-negotiation
after the OEM bits are configured; the restart of auto-negotiation
activates the new OEM bits as does the reset. With 82577/8, the reset is
changed to a generic reset which fixes the LPLU bits getting set wrong.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver provides a regulatory hint to cfg80211 as obtained from the
SPROM. Mostly, this will be a two-letter ISO country code. However, it
may obtain special country code similar to the world regulatory domain
as used in cfg80211. This patch avoids setting these special codes as
the hint is lost to cfg80211.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Brett Rudley <brudley@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The brcmsmac driver provides the country code from sprom as a regulatory
hint to cfg80211. When brcmsmac does not find a country code entry in
the sprom it passes 'US' as regulatory hint. Better approach is to rely
on the world regulatory domain in cfg80211/crda.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Brett Rudley <brudley@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unsupported chip ID and rearrange the list in alphabetical
order
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BRCMF_C_UP is the command that asks the firmware to enable RF of
dongle. Some firmware initialization steps must be performed during
RF is down. Postpone BRCMF_C_UP firing until brcmf_netdev_open get
called to ensure firmware have enough time to finish
initialization.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A header extension is introduced in the received frame to provide
extra space for dongle information. This won't affect current
supported chipset since the data_offset is 0. But it's necessary for
adding support for future chipset.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The primary net device was registered with a primary mac address and
upon IFUP it was set to match the actual mac address from the device.
This patch changes that and moves the brcmf_add_if() call to the common
part of the driver.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mac address for the primary interface was handled different from
the other interfaces. The code has been restructured such that the
brcmf_net_attach function treats the interfaces equal.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function brcmf_net_attach() is only used within dhd_linux.c so
it does not need to be extern. This patch makes the function static.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Ryan Roper <ryan.roper@gmail.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Removes hw.conf.channel usage from the following functions:
* ieee80211_mandatory_rates
* ieee80211_sta_get_rates
* ieee80211_frame_duration
* ieee80211_rts_duration
* ieee80211_ctstoself_duration
This is in preparation for multi-channel operation.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The MAX_TXPWR table for BTCOEX is not needed for AR9462.
Programming these values to the HW results in undesirable
behavior - for example, large number of delimiter/data
underruns are seen in AES-CCMP mode. Also, registers like
AR_PCU_MISC_MODE2 return 0xdeadbeef after the BTCOEX_MAX
power table is programmed to the HW, and frames being transmitted
end up being looped back to the RX engine, an example being beacon
frames in IBSS mode.
Remove this table for now - this fixes CCMP performance and general
IBSS usage.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is needed if we take over after drivers which use those.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't immediately abort .start if DMA is busy before we
initialize the queues. Some drivers do not deinitialize
queues properly and we would fail to take over after them.
This behaviour is consistent with legacy driver.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Legacy driver disables DMA before loading firmware.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce wpdma_disable function to simplify the code.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SMSC911x driver resets the ->head, ->data and ->tail pointers in the
skb on the reset path in order to avoid buffer overflow due to packet
padding performed by the hardware.
This patch fixes the receive path so that the skb pointers are fixed up
after the data has been read from the device, The error path is also
fixed to use number of words consistently and prevent erroneous FIFO
fastforwarding when skipping over bad data.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the ks8851_rdreg16 call above the call to request_irq and cache
the result for subsequent repeated use. A spurious interrupt may
otherwise cause a crash. Thanks to Stephen Boyd, Flavio Leitner, and
Ben Hutchings for feedback.
Signed-off-by: Matt Renzelmann <mjr@cs.wisc.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also fix MAINTAINERS file to reflect autorship.
Daniel and Ariane changed coding style but not any functional changes in the driver
itself.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
We set intr mask before its handler is registered, this does not work well when
8139cp is sharing irq line with other devices. As the irq could be enabled by
the device before 8139cp's hander is registered which may lead unhandled
irq. Fix this by introducing an helper cp_irq_enable() and call it after
request_irq().
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Problem:
There was two separate work_struct structures which share one
handler. Unfortunately getting atl1_adapter structure from
work_struct in case of DMA error was done from incorrect
offset which cause kernel panics.
Solution:
The useless work_struct for DMA error removed and
handler name changed to more generic one.
Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes possible null dereference in probe() function: when both
.mac_addr and .link_gpio are unknown, dev.platform_data may be NULL
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mike Sinkovsky <msink@permonline.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change get_tx_queues, drop unsused arg/return value real_tx_queues,
and use return by value (with error) rather than call by reference.
Probably bonding should just change to LLTX and the whole get_tx_queues
API could disappear!
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ancient times it was necessary to manually initialize the bus field of an
spi_driver to spi_bus_type. These days this is done in spi_driver_register() so
we can drop the manual assignment.
The patch was generated using the following coccinelle semantic patch:
// <smpl>
@@
identifier _driver;
@@
struct spi_driver _driver = {
.driver = {
- .bus = &spi_bus_type,
},
};
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Frederic Lambert <frdrc66@gmail.com>
Cc: netdev@vger.kernel.org
Acked-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e675f0cc9a ("ppp: Don't stop and
restart queue on every TX packet") introduced a race condition which
could leave the net queue stopped even when the channel is no longer
busy. By calling netif_stop_queue() from ppp_start_xmit(), based on the
return value from ppp_xmit_process() but *after* all the locks have been
dropped, we could potentially do so *after* the channel has actually
finished transmitting and attempted to re-wake the queue.
Fix this by moving the netif_stop_queue() into ppp_xmit_process() under
the xmit lock. I hadn't done this previously, because it gets called
from other places than ppp_start_xmit(). But I now think it's the better
option. The net queue *should* be stopped if the channel becomes
congested due to writes from pppd, anyway.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do the initialization of the HSI interface when the
interface is opened, instead of upon registration.
When the interface is closed the HSI interface is
de-initialized, allowing other modules to use the
HSI interface.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CAIF HSI is currently a virtual device. Stopping/starting the
queues is wrong on a virtual device.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement aggregation algorithm, combining more data into a single
HSI transfer. 4 different traffic categories are supported:
1. TC_PRIO_CONTROL .. TC_PRIO_MAX (CTL)
2. TC_PRIO_INTERACTIVE (VO)
3. TC_PRIO_INTERACTIVE_BULK (VI)
4. TC_PRIO_BESTEFFORT, TC_PRIO_BULK, TC_PRIO_FILLER (BEBK)
Signed-off-by: Dmitry Tarnyagin <dmitry.tarnyagin@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull in the 'net' tree to get CAIF bug fixes upon which
the following set of CAIF feature patches depend.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dev_dbg instead of dev_err for reporting in cfhsi_wakeup_cb.
Signed-off-by: Kim Lilliestierna <kim.xx.lilliestierna@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix memory leak of RX flip-buffer.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2e57b79cce misplaced its
parenthesis and now tx_fifo_errors will only be incremented if an
ENOMEM error is not written to the syslog.
Correct the parenthesis and indentation to the original goal of
counting all non ENOMEM errors and ratelimiting only the messages.
Signed-of-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move these as part of iwl-core.h cleanup.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Move these functions to iwl-agn.h as part of
iwl-core.h cleanup.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Move this as part of iwl-core.c cleanup.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Move this function as part of iwl-core.c cleanup.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Move this as part of iwl-core.c cleanup.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Move this as part of iwl-core.c cleanup.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Move this as part of iwl-core.c cleanup.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This function is used only in iwl-agn-rxon.c,
move it there and mark it static.
Move this function as part of iwl-core.c
cleanup.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Move this as part of iwl-core.c cleanup.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Move this as part of iwl-core.c cleanup.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Move this as part of iwl-core.c cleanup.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Move this as part of iwl-core.c cleanup.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Moving this as part of iwl-core.c cleanup.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Moving this as part of iwl-core.c cleanup.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Moving this as part of iwl-core.c cleanup.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This is really something determined by
station parameters, so move it to
iwl-agn-sta.c.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
iwl_set_hw_rfkill_state is used only in
iwl-agn.c. Move it there and mark it static.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
iwl_free_skb is used only in iwl-agn.c, move
it there and mark it static.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
With the creation of iwl-agn-devices.c,
iwl-core.c can be cleaned up a bit more by
moving beacon time related functions from
iwl-core.c to iwl-agn-devices.c
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Not all stations are guaranteed to have the same
active (available) legacy rates, so calculate them
on rate control init instead of hard-coding them
based on our own available rates. I have no idea
why that was done here before.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Since this function is now used only by
op_mode, remove it from iwl-shared.h and move
it to iwl-agn.h.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Pull networking fixes from David Miller:
1) Fix bluetooth userland regression reported by Keith Packard, from
Gustavo Padovan.
2) Revert ath9k PS idle change, from Sujith Manoharan.
3) Correct default TCP memory limits (again), from Eric Dumazet.
4) Fix tcp_rcv_rtt_update() accidental use of unscaled RTT, from Neal
Cardwell.
5) We made a facility for layers like wireless to say how much tailroom
they need in the SKB for link layer stuff such as wireless
encryption etc., but TCP works hard to fill every SKB out to the end
defeating this specification.
This leads to every TCP packet getting reallocated by the wireless
code in order to have the right amount of tailroom available.
Fix TCP to only fill SKBs out to the real amount of data area it
asked for during the allocation, this way it won't eat into the
slack added for the device's tailroom needs.
Reported by Marc Merlin and fixed by Eric Dumazet.
6) Leaks, endian bugs, and new device IDs in bluetooth from Santosh
Nayak, João Paulo Rechi Vita, Cho, Yu-Chen, Andrei Emeltchenko,
AceLan Kao, and Andrei Emeltchenko.
7) OOPS on tty_close fix in bluetooth's hci_ldisc from Johan Hovold.
8) netfilter erroneously scales TCP window twice, fix from Changli Gao.
9) Memleak fix in wext-core from Julia Lawall.
10) Consistently handle invalid TCP packets in ipv4 vs. ipv6 conntrack,
from Jozsef Kadlecsik.
11) Validate IP header length properly in netfilter conntrack's
ipv4_get_l4proto().
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (39 commits)
NFC: Fix the LLCP Tx fragmentation loop
rtlwifi: Add missing DMA buffer unmapping for PCI drivers
rtlwifi: Preallocate USB read buffers and eliminate kalloc in read routine
tcp: avoid order-1 allocations on wifi and tx path
net: allow pskb_expand_head() to get maximum tailroom
bridge: Do not send queries on multicast group leaves
MAINTAINERS: Mark NATSEMI driver as orphan'd.
tcp: fix tcp_rcv_rtt_update() use of an unscaled RTT sample
tcp: restore correct limit
Revert "ath9k: fix going to full-sleep on PS idle"
rt2x00: Fix rfkill_polling register function.
bcma: fix build error on MIPS; implicit pcibios_enable_device
netfilter: nf_conntrack: fix incorrect logic in nf_conntrack_init_net
netfilter: nf_ct_ipv4: packets with wrong ihl are invalid
netfilter: nf_ct_ipv4: handle invalid IPv4 and IPv6 packets consistently
net/wireless/wext-core.c: add missing kfree
rtlwifi: Fix oops on rate-control failure
mac80211: Convert WARN_ON to WARN_ON_ONCE
rtlwifi: rtl8192de: Fix firmware initialization
nl80211: ensure interface is up in various APIs
...
Define and use the bits of the PHY_CC (status change configuration) register.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define MTPR bit 0 of the register and use it where it is appropriate.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define the MLSR (MAC Last Status Register bits) for:
- tx fifo under-run
- tx exceed collision
- tx late collision
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are currently updating the rx fifo error counter in the tx path while
it should have been the tx fifo error counter, fix that.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2048 is the usual value for busy-waiting on a register r/w, define it
as MAC_DEF_TIMEOUT and use it where it is appropriate.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reset of the MAC is currently done identically from two places
and one place is not waiting for the MAC_SM bit to be set after reset.
Everytime the MAC is software resetted a state machine is also needed
so consolidate the reset to its own function.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
m68k/allmodconfig:
drivers/net/ethernet/wiznet/w5100.c: In function ‘w5100_hw_probe’:
drivers/net/ethernet/wiznet/w5100.c:680: error: ‘IRQ_TYPE_LEVEL_LOW’ undeclared (first use in this function)
drivers/net/ethernet/wiznet/w5300.c: In function ‘w5300_hw_probe’:
drivers/net/ethernet/wiznet/w5300.c:594: error: ‘IRQ_TYPE_LEVEL_LOW’ undeclared (first use in this function)
Include <linux/irq.h>, which provides the declaration for IRQ_TYPE_LEVEL_LOW.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This option was there for debugging race conditions,
just remove it, and assume TX_FLOW is always enabled.
Signed-off-by: Mike Sinkovsky <msink@permonline.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Having the pointer to lib_ops in the config
makes it impossible to split the driver into
different modules. Determine the ops based on
the device family enumeration to get rid of
the direct pointer.
Also move all the opmode specific code from
the iwl-[1256]000.c files into a new file
iwl-agn-devices.c so that the former only
have configuration data now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver doesn't report its supported cipher suites through cfg80211
interface. It still uses wext interface and probably will not work
through nl80211, but will at least correctly advertise supported
features.
Bug was reported by Omar Siam.
https://bugzilla.kernel.org/show_bug.cgi?id=43049
Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make use of request_firmware_nowait instead of request_firmware
to load FW asynchronously. This fixes timeouts introduced with
recent udev changes.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patches enables setting association request and probe request
IE for station interface. WPS exchange between WPS2.0 AP and mwifiex
STA Enrollee/External Registrar completes successfully.
Tested with wpa_supplicant 1.0 and 2.0 devel.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use "priv->country_code" string to display country information in
debugfs command "info" instead of "adapter->region_code".
"adapter->region_code" contains default region code got from FW while
initialization, whereas "priv->country_code" is updated in reg_notifier
handler whenever there is a change in regulatory domain.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver gets region code from FW during initialisation. This patch
makes use of it for settting default regulatory domain using
regulatory_hint() API.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a copy-n-paste error introduced in recent patch
"mwifiex: add set_cqm_rssi_config handler support".
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will later be used to dynamically bind
the configuration data for DVM and MVM.
For now, we can use it to get rid of the
additional_nic_config() hook.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The iwl-shared.h header file will be going away
soon. There isn't much left in it that we keep,
other than the device configuration declarations.
Move those out now to a new iwl-config.h header.
iwl-cfg.h seemed like a possible alternative but
those declarations will later live in the PCIe
transport code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The whole code around eeprom is distributed
across whole bunch of different files, most
of which belong to the to-be-DVM code. As a
result, it is currently very hard to split
out the EEPROM code to be generic. However,
it is also quite unlikely that the current
EEPROM code will be needed by the MVM code
as that has different mechanisms to query
the EEPROM (it does so through the uCode.)
So, at least temporarily, move everything
into priv. If it becomes necessary to use
the code from MVM, we will have to split it
out, but then it's also easier since we'll
know what pieces we need.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split the force_reset debugfs file into two
different files:
* "rf_reset" triggers a reset of the RF when
written to and exposes statistics on RF
resets when read
* fw_restart triggers a firmware restart when
written to and lives in the transport
This cleans up all sources of firmware restart
to originate within the transport layer and
allows us to simplify some code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This defaults to false, and we don't recommend
to use it anywhere, so just remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hw_params are mostly values that are
derived from the actual hardware config.
As such, while it is possible that MVM
will require similar ones, it makes more
sense -- at least for now -- to put them
into the DVM struct.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes one of the two sources of device
restarts in the upper layer -- those are a bit
inconvenient because normal restarts originate
in the transport. By moving the watchdog down
it can be treated the same.
Also rewrite the watchdog logic. Timers are
much more efficient when they never fire, so
instead firing a timer every 500ms set up a
timer for each TX queue and fire it only when
the queue is really stuck. This avoids the CPU
waking up when everything is working well.
While at it, remove the wd_disable config item
and replace it by simply setting wd_timeout to
IWL_WATCHHDOG_DISABLED (0).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This file isn't really all that useful as
when the watchdog triggered it's already
too late, and the setting doesn't persist
unlike e.g. a module parameter that could
be added to the right config file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
That way it isn't needed in hw_params, which
is shared data. It also isn't really what we
should configure in the transport, that is
better just 4k/8k, so configure a bool and
derive the page order in the transport. This
also means the transport doesn't need access
to the module parameter any more.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The release_firmware() function does its own NULL test so a test
before calling it is rather redundant.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is redundant to test for NULL pointers before calling
release_firmware() since the function does its own NULL test.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since release_firmware() does its own test for NULL it is redundant to
do so before calling it.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
release_firmware() tests for, and deals gracefully with, NULL
pointers. Remove redundant explicit tests before calling the function.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The release_firmware() function does its own NULL test, so testing
before calling it is rather redundant.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
release_firmware() does its own test. Explicitly checking before the
call is redundant.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The release_firmware() function deals gracefully with being passed a
NULL pointer, so explicit tests before the call are rather pointless.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The chip version constant (0xCC33) was taken from version 0001.0105.2011
of the GPL vendor driver. Note that this driver version also ships a
firmware update, but I am unsure if it is required for E-CUT chips to
function properly.
A nearby spelling error was also corrected.
Signed-off-by: Forest Bond <forest.bond@rapidrollout.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The previous definitions included both {B,C,D,E}_CUT_VERSION and
CHIP_92D_{C,D}_CUT with conflicting values for the C and D cut versions,
and literal hex values were used in the IS_92D_{C,D,E}_CUT macros. So
we clean all this up and in doing so enable cut-specific code paths for
cuts C and D, which would not have been executed because the
CHIP_92D_{C,D}_CUT constants were wrong and the cut version was thus
recorded incorrectly.
Signed-off-by: Forest Bond <forest.bond@rapidrollout.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added support for Belkin Surf N300 XR wireless usb adapter to rtlwifi driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add room for a private data struct at the end of the common FW status.
Add a convenience "counters" struct inside the FW status.
The wl12xx family does not currently use the FW status private data.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Rajkumar Manoharan