dmaw_block is never used in the driver, remove it.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
some fields of REG_DMA_CTRL(15C0) are wrong, replace with the newest one.
haredware uses fixed dma-write-block size, remove dmaw_block related code
in function atl1c_configure_dma.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
function atl1c_stop_mac uses wrong register of REG_TWSI_CTRL
to stop mac, replace it with REG_TXQ_CTRL.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove code related to rxq 1/2/3 since multi-q not support.
refine REG_RXQ_CTRL definition as well.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TPD producer/consumer index is 16bit wide.
16bit read/write reduce the dependency of the 2 tpd rings (hi and lo)
rename reg(157C/1580) to keep name coninsistency.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
l1c & later chips don't support DMA for SMB.
CMB is removed from hardware.
reg(15C8) is used to trig interrupt by tpd threshold.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VPD register is only used for L1(devid=PCI_DEVICE_ID_ATTANSIC_L1) to
access external NV-memory.
l1c & later chip doesn't use it any more.
PHY 0/1 registers occupy the last 2 slots of the dump table.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove HDS register as it doesn't exist in hardware.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the multiple-RX-Q in hardware doesn't work,
all related register definition & code are removed.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
replace unavailable email of the author since he left with a mail-list.
update company info as well, Atheros was acquired by Qualcomm.
insert "100" to driver description since it support 100M controller.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* remove duplicated line in comment
* add htons() invocation for tt_crc as suggested by Al Viro
* OriGinator Message seqno initial value is now random
* some cleanups and fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJPjnVmAAoJEFMQTLzJFOZFqpkH/33gzND7Ukfdax6CPYqb1AVm
A63gtnZlNCwPf7dCJkq4yF4RVn/ir1pp+BwX5C9BIN9V/ZSaTsIKsMXAaZzUK3DH
PCZEJCn+iys+ZX5KrpLum0wMSQyxt08GsGZLueiu+Rm0zRZLSCy58THNqLt2b6ZK
mDH6tdbGxKXxrKeWzVz3PzQv8dPuFqApPiQ+M6ugf4YvjdYYEiGWFn8gad+XObeA
oxbFGMt6MKdc+9EsKqd0Br1lqHiQ+RC2xXQiFEBizPe34LiYJ69irkEBki/6KV9Z
ujeB0RxlMHXL75vUWoqyGcv/F2lzZd/tXQA6qz7ioCBHqzb1Mk/KGmVJ3KZ5CK8=
=9lku
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Included changes:
* remove duplicated line in comment
* add htons() invocation for tt_crc as suggested by Al Viro
* OriGinator Message seqno initial value is now random
* some cleanups and fixes
This is done so that it can be reused with differing publication
lists, instead of being hard coded to the cluster publicaton list.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
There is currently a single list that is containing both cluster-scope and
zone-scope publications, and the list count is a separate free floating
variable. Create a struct to bind the count to the list, and to pave
the way for factoring out the publications into zone/cluster/node scope.
The current "publ_root" most matches what will be the cluster scope
list, so it is named accordingly in this commit.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
When we receive an OGM from from a node for the first time, the last_real_seqno
field of the orig_node structure has not been initialised yet. The value of this
field is used to compute the current ogm-seqno window and therefore the
protection mechanism will probably drop the packet due to an out-of-window error.
To avoid this situation this patch adds a check to skip the window protection
mechanism if no neighbour nodes have already been added. When the first
neighbour node is added, the last_real_seqno field is initialised too.
Reported-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
OGM sequence numbers are declared as uint32_t and so they have to printed
using %u instead of %d in order to avoid wrong representations.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Instead of using sizeof(struct ethhdr) it is strongly recommended to use the
kernel macro ETH_HLEN. This patch substitute each occurrence of the former
expressione with the latter one.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The coming protocol changes also will have a part called "OGM". That
makes it necessary to introduce a distinction in the code base.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Using BATMAN_OGM_LEN leaves one with the impression that this is
the full packet size which is not the case. Therefore the variable
is renamed.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Before sending out a TT_Request packet we must convert the tt_crc field value
to network order (since it is 16bits long).
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The driver does not always use the same timing for what looks like
the same operations.
- DCR0
Use the same udelay everywhere for reset. Upper bound is 100 us.
- DCR9
Use 5us delay for srom clock. 1us delay for phy_write_1bit (writes
PHY_DATA_[01]) are not changed as they stay withing a 2,5MHz MDIO
clock range.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix mixed space and tabs.
Put bpf_jit_load_*[] externs into bpf_jit.h
"while(0)" --> "while (0)"
"COND (X)" --> "COND(X)"
Document branch offset calculations, and bpf_error's return
sequence.
Document the reason we need to emit three nops between the
%y register write and the divide instruction.
Remove erroneous trailing semicolons from emit_read_y() and
emit_write_y().
Based upon feedback from Sam Ravnborg.
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct conventions comments. %o4 and %o5 were swapped,
%g3 was not documented.
Use r_TMP instead of r_SKB_DATA + r_OFF where possible in
assembler stubs.
Correct discussion of %o4 and %o5 in one of bpf_jit_compile()'s
comments.
Based upon feedback from Richard Mortimer.
Signed-off-by: David S. Miller <davem@davemloft.net>
We get two timing related fields for each bss from firmware in scan
results.
1) timestamp - Actual timestamp information in probe response/beacon
2) network_tsf - firmware's TSF value at the time the beacon or probe
response was received.
Both are needed while associating by firmware.
The patch takes care of following things.
1) We should pass "timestamp" to cfg80211_inform_bss(), but currently
"network_tsf" is being provided. This error is corrected here.
2) Rename "network_tsf" to "fw_tsf"
3) Make use of u64 variable instead of an array of u8/u32 to save
parsed "timestamp" information.
4) Use timestamp provided to stack in scan results using
cfg80211_inform_bss() while associating. (bss->tsf)
5) Allocate space to save fw_tsf in "priv" of cfg80211_bss
and retrieve it while associating.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rearrange some code to save extra parameters to the functions.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As described at
http://article.gmane.org/gmane.linux.kernel.wireless.general/86084
libertas is taking a long time to load because it loads firmware
during module loading.
Add a new API for interface drivers to load their firmware
asynchronously. The same semantics of the firmware table are followed
like before.
Interface drivers will be converted in follow-up patches, then we can
remove the old, synchronous firmware loading function.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These simple sanity check avoids extra complexity in error paths when
moving to asynchronous firmware loading (which means the device may fail to
init some time after its creation).
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the ability to pass module parameters with firmware filenames
for USB and SDIO interfaces.
Remove the ability to pass custom "user" filenames to lbs_get_firmware().
Remove the ability to reprogram internal device memory with a different
firmware from the USB driver (we don't know of any users), and simplify
the OLPC firmware loading quirk to simply placing the OLPC firmware
at the top of the list (we don't know of any users other than OLPC).
Move lbs_get_firmware() into its own file.
These simplifications should have no real-life effect but make the
upcoming transition to asynchronous firmware loading considerably less
painful.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are connection stalls or very poor throughputs with rt2800
hardware using 802.11n in AP mode since patch "mac80211: retry sending
failed BAR frames later instead of tearing down aggr"[1][2].
Since rt2800 hardware is not able to correctly report the tx status of
BAR frames, this patch removes as workaround the existing error handling
on AP side, which lets mac80211 send a BAR when an AMPDU subframe fails.
As a result, most wifi clients (aside from Intel STAs on Windows)
instead will timeout now the reorder buffer and request the lost frame
again.
The correct solution would be, to tear down BA session on AP side.
This patch was born on the basis of "[RFT] rt2x00: Tear down BA
session on QoS frame failure"[3].
Thanks to Helmut Schaa for his support!
[1] http://thread.gmane.org/gmane.linux.kernel.wireless.general/83297/focus=83304
[2] http://git.kernel.org/?p=linux/kernel/git/linville/wireless-testing.git;a=commit;h=f0425beda4d404a6e751439b562100b902ba9c98
[3] http://thread.gmane.org/gmane.linux.drivers.rt2x00.user/569
Signed-off-by: Andreas Hartmann <andihartmann@01019freenet.de>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The FBIN2FREQ macro and the ath9k_hw_fbin2freq function
does the same thing. Remove the macro, and use the inline
function instead.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both eeprom.c and ar9003_eeprom.c has an indentical
'ath9k_hw_fbin2freq' function. Move the function to
a common place and remove the duplicates.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The existing constants are used for reduction/increase
tx power level on devices with 2x2 and 3x3 chainmask.
Both reduction and increase must use the same value, so
it makes no sense to use separate constants for them.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a corresponding leave call on error failure.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Compared with previous chipsets, it needs no special action trough the
jumbo{enable/disable} helpers to operate with jumbo frames.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Huang, Xiong