This removes all of the clock init code from da8xx-dt.c. This includes
all of the OF_DEV_AUXDATA that was just used for looking up clocks.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This removes the unused legacy clock init code from
arch/arm/mach-davinci/da850.c.
Signed-off-by: David Lechner <david@lechnology.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This adds the new USB PHY clock init in mach-davinci/usb-da8xx.c using
the new common clock framework drivers.
The #ifdefs are needed to prevent compile errors until the entire
ARCH_DAVINCI is converted.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This adds the new board-specific clock init in mach-davinci/da850.c
using the new common clock framework drivers.
The #ifdefs are needed to prevent compile errors until the entire
ARCH_DAVINCI is converted.
Also clean up the #includes since we are adding some here.
Some CFGCHIP macros were removed because we are now including
linux/mfd/da8xx-cfgchip.h which defines the same values.
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This moves the call of davinci_clk_init() from map_io to init_time for all
boards.
This is the proper place to init clocks. This is also done in preparation
for moving to the common clock framework.
dm646x is a special case because we need to handle different ref_clk rates
depending on which board is being used. The clock init in this case is
modified to set the rate before registering the clocks instead of using
davinci_set_refclk_rate() to recalculate the entire clock tree after all
of the clocks are registered.
Also, the cpu_clks field is removed from struct davinci_soc_info since it
is no longer needed.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This removes the watchdog reset code. The reset has been moved to
drivers/watchdog/davinci_wdt.c. The watchdog driver registers the reset
with the kernel so defining a reset for each machine is no longer needed.
Signed-off-by: David Lechner <david@lechnology.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add the OF_DEV_AUXDATA entry needed to match the device-tree DSP node
to its non-device-tree clock, so that the da8xx-remoteproc driver can
properly enable the clocks. The device name has also been assigned
"davinci-rproc.0" to match the device id used in the da850_clks
clk_lookup array.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This is needed for the driver to access the vpif clock.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
[Bartosz: split the pdata-quirks patch in two with one
adding the OF_DEV_AUXDATA entry]
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
In the SoC branch we normally collect classic arch/arm/mach-* contents, i.e.
C code changes for SoC platforms. This release cycle the diffstat is quite
nice, in that we're removing 3x the amount of code that's being added.
The main reason for this is that there's a removal of camera drivers for
Freescale i.MX chips (driver was removed so the device registration isn't
needed any more). There's also removal of display initialization code for OMAP
that is no longer needed.
The rest are mostly minor tweaks and cleanups; constification on Samsung
platforms, cleanup of ux500 platform data, purge of other unused platform
data/device seutp on i.MX and other good stuff.
New SoC support this cycle is for two Allwinner platforms, H2+ and V3s.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YE8v
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"In the SoC branch we normally collect classic arch/arm/mach-*
contents, i.e. C code changes for SoC platforms. This release cycle
the diffstat is quite nice, in that we're removing 3x the amount of
code that's being added.
The main reason for this is that there's a removal of camera drivers
for Freescale i.MX chips (driver was removed so the device
registration isn't needed any more). There's also removal of display
initialization code for OMAP that is no longer needed.
The rest are mostly minor tweaks and cleanups; constification on
Samsung platforms, cleanup of ux500 platform data, purge of other
unused platform data/device seutp on i.MX and other good stuff.
New SoC support this cycle is for two Allwinner platforms, H2+ and
V3s"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (55 commits)
ARM: ux500: remove deleted file from Makefile
ARM: ep93xx: Disable TS-72xx watchdog before uncompressing
ARM: ux500: cut some platform data
MAINTAINERS: Update for the current location of the bcm2835 tree.
ARM: davinci: remove BUG_ON() from da850_register_sata()
ARM: davinci: da850: model the SATA refclk
ARM: davinci: da850: add con_id for the SATA clock
ARM: davinci: da8xx-dt: add OF_DEV_AUXDATA entry for SATA
arm: mvebu: support for SMP on 98DX3336 SoC
dt-bindings: video: exynos7-decon: Remove obsolete samsung,power-domain property
soc: dove: constify reset_control_ops structures
ARM: mv78xx0: fix possible PCI buffer overflow
MAINTAINERS: transfer maintainership for the EZX platform
ARM: shmobile: rcar-gen2: Add more register documentation
ARM: tegra: paz00: Fix __initdata placement
ARM: OMAP: clock: Remove unused mpurate cmdline option
ARM: davinci: add skeleton for pdata-quirks
arm: sunxi: add support for V3s SoC
ARM: OMAP2+: omap_hwmod: Add support for earlycon
arm: hisi: drop extern hip01_cpu_die
...
Register a fixed rate clock modelling the external SATA oscillator
for da850 (both DT and board file mode).
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This entry is needed for the ahci driver to get a functional clock.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
[nsekhar@ti.com: subject line adjustment]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add skeleton pdata-quirks for davinci.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
[nsekhar@ti.com: move changes to build pdata-quirks.c and call
to pdata_quirks_init() to this patch]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The aemif driver can now access struct of_dev_auxdata (using platform
data).
Add the device id to the clock lookup table for the nand clock and
create a separate lookup table for aemif subnodes.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These are updates for platform specific code on 32-bit ARM machines,
essentially anything that can not (yet) be expressed using DT files.
Noteworthy changes include:
- Added support for the TI DRA71x family of SoCs in mach-omap2,
this is an new variant of the the DRA72x/DRA74x automotive
infotainment chips we already supported for a while.
- Added support for the ST STM32F746 SoC, the first Cortex-M7
based microcontroller we support, related to the smaller
STM32F4 family.
- Renesas adds support for r8a7743 and r8a7745 in mach-shmobile,
see http://elinux.org/RZ-G
- SMP is now supported on the OX820 platform
- A lot of code in mach-omap2 gets removed as a follow-up to
removing support for board files in the previous release
- Davinci has some new work to improve USB support
- For i.MX, the performance monitor now supports profiling the
memory controller using 'perf'
Conflicts:
arch/arm/mach-shmobile/setup-rcar-gen2.c: rcar_gen2_clocks_init()
is gone, calling of_clk_init(NULL) is sufficient now.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BF6Y
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"These are updates for platform specific code on 32-bit ARM machines,
essentially anything that can not (yet) be expressed using DT files.
Noteworthy changes include:
- Added support for the TI DRA71x family of SoCs in mach-omap2, this
is an new variant of the the DRA72x/DRA74x automotive infotainment
chips we already supported for a while.
- Added support for the ST STM32F746 SoC, the first Cortex-M7 based
microcontroller we support, related to the smaller STM32F4 family.
- Renesas adds support for r8a7743 and r8a7745 in mach-shmobile, see
http://elinux.org/RZ-G
- SMP is now supported on the OX820 platform
- A lot of code in mach-omap2 gets removed as a follow-up to removing
support for board files in the previous release
- Davinci has some new work to improve USB support
- For i.MX, the performance monitor now supports profiling the memory
controller using 'perf'"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (95 commits)
ARM: davinci: da830-evm: use gpio descriptor for mmc pins
ARM: davinci: da850-evm: use gpio descriptor for mmc pins
ARM: davinci: hawk: use gpio descriptor for mmc pins
ARM: ARTPEC-6: add select MFD_SYSCON to MACH_ARTPEC6
ARM: davinci: da8xx: Fix ohci device name
ARM: oxnas: Add OX820 config and makefile entry
ARM: oxnas: Add OX820 SMP support
ARM: davinci: PM: fix build when da850 not compiled in
ARM: orion5x: remove legacy support of ls-chl
ARM: integrator: drop EBI access use syscon
ARM: BCM5301X: Add back handler ignoring external imprecise aborts
ARM: davinci: PM: support da8xx DT platforms
ARM: davinci: PM: cleanup: remove references to pdata
ARM: davinci: PM: rework init, remove platform device
ARM: Kconfig: Introduce MACH_STM32F746 flag
ARM: mach-stm32: Add a new SOC - STM32F746
ARM: shmobile: document SK-RZG1E board
ARM: shmobile: r8a7745: basic SoC support
ARM: imx: mach-imx6ul: add imx6ull support
ARM: zynq: Reserve correct amount of non-DMA RAM
...
While the clk lookup table is making reference to "ohci"
other subsystems (such as phy) are trying to match "ohci.0"
Since there is a single ohci instance, instead of changing
the clk name, change the dev id to -1, and add the "-da8xx"
postfix to match the driver name that will also be changed
in a subsequent patch.
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This fixes pwm name matching for DA850 familiy devices. When using device
tree, the da850_auxdata_lookup[] table caused pwm devices to have the exact
same name, which caused errors when trying to register the devices.
We cannot have multiple entries for the same clock in in da850_clks[], so
we have added child clocks to the EHRPWM and ECAP LPSC clocks so that each
PWM device will have its own clock for proper name matching.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The usb20_phy clock needs to be registered for the driver to be able
to get and enable a clock. Currently the usb phy clocks are registered
from board files, which will not be called during a device tree based
boot.
To be able to probe correctly usb form a device tree boot, register
the usb phy clocks from the DT specific init.
Unfortunately, davinci does not have proper clock support on device tree
yet, so by registering the clock from the DT specific file we are
forced to hardcode the parent clock, and cannot select refclkin as
parent for any of the phy clocks of the da850 family.
As none of the current da850 based boards currently in mainline use
refclkin as source. I guess we can live with this limitation until clocks
are correctly represented through CCF/device tree.
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
[Added error checking]
Signed-off-by: David Lechner <david@lechnology.com>
[nsekhar@ti.com: typo fixes in commit message]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add OF_DEV_AUXDATA() entry for USB phy. This is required for
so that clock lookup will work for the USB PHY driver.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This adds device names for the SoC USB devices to the clock lookup tables
in da830.c and da850.c.
Also add the USB device names to the da850_auxdata_lookup[] table.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This is required for tilcdc to be able to acquire a functional clock
on da850 SoCs.
Signed-off-by: Karl Beldan <kbeldan@baylibre.com>
[Bartosz:
- added the commit description
- changed the compatible string to 'ti,da850-tilcdc']
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
These are as usual a very large number of mostly boring updates to
enable devices in existing machines, or to fix minor bugs. Notably,
an ongoing treewide effort to fix warnings caused by an update to the
device tree compiler. These are enabled with "make W=1" at the moment
but can hopefully become the default once all issues have been addressed.
No new SoC platform is added this time around (Armada 395 and Orion
mv88f5181 are slight variations of existing ones), but a significant
number of new dts files are added, which I list by platform:
- Allwinner: Empire Electronix M712 and iNet d978 Rev2 tablets;
Orange Pi PC Plus, Orange Pi 2, Orange Pi Plus 2E,
Orange Pi Lite, Olimex A33-Olinuxino, and Nano Pi Neo
single-board computers
- ARM Realview: all supported machines (ported from board files)
- Broadcom: BCM958525er, BCM958522er, BCM988312hr, BCM958623hr and
BCM958622hr reference boards for Northstar platform;
Raspberry Pi Zero single-board computer
- Marvell EBU: Netgear WNR854T router (ported from board file);
Armada 395 SoC platform and GP board
Armada 390 DB development board
- NXP i.MX: imx7s Warp7 reference board;
Gateworks Ventana GW553x single-board computer,
Technologic Systems TS-4900 and
Engicam IMX6UL GEA M6UL computer-on-module,
Inverse Path USB armory board
- Qualcomm: LG Nexus 5 Phone
- Renesas: r8a7792/wheat and r7s72100/rskrza1 development boards
- Rockchip: Rockchip RK3288 Fennec reference board;
Firefly RK3288 Reload platform
- ST Microelectronics STi: B2260 (96boards) single-board computer
- TI Davinci: OMAP-L138 LCDK Development kit
- TI OMAP: beagleboard-x15 rev B1 single-board computer
Conflicts: vendor-prefixes.txt has conflicting additions, keep all of
them in alphabetical order.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/gg/
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"These are as usual a very large number of mostly boring updates to
enable devices in existing machines, or to fix minor bugs. Notably, an
ongoing treewide effort to fix warnings caused by an update to the
device tree compiler. These are enabled with "make W=1" at the moment
but can hopefully become the default once all issues have been
addressed.
No new SoC platform is added this time around (Armada 395 and Orion
mv88f5181 are slight variations of existing ones), but a significant
number of new dts files are added, which I list by platform:
- Allwinner: Empire Electronix M712 and iNet d978 Rev2 tablets,
Orange Pi PC Plus, Orange Pi 2, Orange Pi Plus 2E, Orange Pi Lite,
Olimex A33-Olinuxino, and Nano Pi Neo single-board computers
- ARM Realview: all supported machines (ported from board files)
- Broadcom: BCM958525er, BCM958522er, BCM988312hr, BCM958623hr and
BCM958622hr reference boards for Northstar platform, Raspberry Pi
Zero single-board computer
- Marvell EBU: Netgear WNR854T router (ported from board file),
Armada 395 SoC platform and GP board Armada 390 DB development
board
- NXP i.MX: imx7s Warp7 reference board, Gateworks Ventana GW553x
single-board computer, Technologic Systems TS-4900 and Engicam
IMX6UL GEA M6UL computer-on-module, Inverse Path USB armory board
- Qualcomm: LG Nexus 5 Phone
- Renesas: r8a7792/wheat and r7s72100/rskrza1 development boards
- Rockchip: Rockchip RK3288 Fennec reference board, Firefly RK3288
Reload platform
- ST Microelectronics STi: B2260 (96boards) single-board computer
- TI Davinci: OMAP-L138 LCDK Development kit
- TI OMAP: beagleboard-x15 rev B1 single-board computer"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (390 commits)
ARM: dts: sony-nsz-gs7: add missing unit name to /memory node
ARM: dts: chromecast: add missing unit name to /memory node
ARM: dts: berlin2q-marvell-dmp: add missing unit name to /memory node
ARM: dts: berlin2: Add missing unit name to /soc node
ARM: dts: berlin2cd: Add missing unit name to /soc node
ARM: dts: berlin2q: Add missing unit name to /soc node
ARM: dts: berlin2: Remove skeleton.dtsi inclusion
ARM: dts: berlin2cd: Remove skeleton.dtsi inclusion
ARM: dts: berlin2q: Remove skeleton.dtsi inclusion
arm: dts: berlin2q: enable all wdt nodes unconditionally
arm: dts: berlin2: enable all wdt nodes unconditionally
ARM: dts: omap5-igep0050.dts: Use tabs for indentation
ARM: dts: Fix igepv5 power button GPIO direction
ARM: dts: am335x-evmsk: Add blue-and-red-wiring -property to lcdc node
ARM: dts: am335x-evmsk: Whitespace cleanup of lcdc related nodes
ARM: dts: am335x-evm: Add blue-and-red-wiring -property to lcdc node
ARM: dts: s3c64xx: Use macros for pinctrl configuration
ARM: dts: s3c2416: Use macros for pinctrl configuration
ARM: dts: s5pv210: Use macros for pinctrl configuration
ARM: dts: s3c64xx: Use common macros for pinctrl configuration
...
The davinci boards don't have their clocks in DT yet and getting a clock
will fail, unless registering them as clk_lookups. This registers the
aemif clock for the ti-aemif memory driver.
The current aemif lookup entry resolving to the same clock:
'CLK(NULL, "aemif", &aemif_clk)'
is currently used by davinci_nand and remains for non-DT and backward
compatibility.
Currently the davinci boards only configure the AEMIF in case of non-DT
boot, via some code in mach-davinci.
This change will allow DT-based davinci platforms to do the same, via
the ti-aemif memory driver code.
Signed-off-by: Karl Beldan <kbeldan@baylibre.com>
[nsekhar@ti.com: reworded commit message]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The LCDK is the successor to the late Hawkboard.
Among the differences are the flash (16bits vs 8bits) and some pins
(MMC, LEDs, buttons, some external connectors), however the main
components remain the same (eth. phy, audio codec, video decoder and
DAC) except for the main PMIC, different and hard-wired on the LCDK (the
LDOs and DCDCs are always on).
A DT-only boot with this addition gives functional UART, reboot via
watchdog, RTC, ethernet and MMC (I added the CD GPIO for the MMC
although davinci_mmc doesn't call the OF facilities of mmc core).
Cc: Sekhar Nori <nsekhar@ti.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Karl Beldan <kbeldan@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
These are all the updates to device tree files for 32-bit platforms,
which as usual makes up the bulk of the ARM SoC changes: 462 non-merge
changesets, 450 files changed, 23340 insertions, 5216 deletions.
The three platforms that are added with the "soc" branch are here as well,
and we add some related machine files:
- For Aspeed AST2400/AST2500, we get the evaluation platform and
the Tyan Palmetto POWER8 mainboard that uses the AST2400 BMC
- For Oxnas 810SE, the Western Digital "My Book World Edition"
is added as the only platform at the moment.
- For ARM MPS2, the AN385 (Cortex-M3) and AN399 (Cortex-M7)
are supported
On the ARM Realview development platform, we now support all machines
with device tree, previously only the board files were supported, which
in turn will likely be removed soon.
Qualcomm IPQ4019 is the second generation ARM based "Internet Processor",
following the IPQ806x that is used in many high-end WiFi routers. This one
integrates two ath10k wifi radios that were previously on separate chips.
Other boards that got added for existing chips are:
- On Ti OMAP family:
- Amazon Kindle Fire, first generation, tablet and ebook reader
- OnRISC Baltos iR 2110 and 3220 embedded industrial PCs
- TI AM5728 IDK, TI AM3359 ICE-V2, and TI DRA722 Rev C EVM
development systems
- On Samsung EXYNOS platform:
- Samsung ARTIK5 evaluation board, see
https://www.artik.io/modules/overview/artik-5/
- On NXP i.MX platforms:
- Ka-Ro electronics TX6S-8034, TX6S-8035, TX6U-8033, TX6U-81xx,
TX6Q-1036, TX6Q-1110/-1130, TXUL-0010 and TXUL-0011 industrial
SoM modules
- Embest MarS Board i.MX6Dual DIY platform
- Boundary Devices i.MX6 Quad Plus Nitrogen6_MAX and
SoloX Nitrogen6sx embedded boards
- Technexion Pico i.MX6UL compute module
- ZII VF610 Development Board
- On Marvell embedded (mvebu, orion, kirkwood) platforms:
- Linksys Viper (E4200v2 / EA4500) WiFi router
- Buffalo Kurobox Pro NAS
- On Qualcomm Snapdragon:
- Arrow DragonBoard 600c (96boards) with APQ8064 Snapdragon 600
- On Rockchips platform:
- mqmaker MiQi single-board computer
- On Altera SoCFPGA:
- samtec VIN|ING 1000 vehicle communication interface
- On Allwinner Sunxi platforms:
- Dserve DSRV9703C tablet
- Difrnce DIT4350 tablet
- Colorfly E708 Q1 tablet
- Polaroid MID2809PXE04 tablet
- Olimex A20 OLinuXino LIME2 single board computer
- Xunlong Orange Pi 2, Orange Pi One, and Orange Pi PC
single board computers
Across many platforms, bug fixes went in to address warnings that
dtc now emits with 'make dtbs W=1'. Further changes for device enablement
went into Ti OMAP, bcm283x (Raspberry Pi), bcm47xx (wifi router),
Ti Davinci, Samsung EXYNOS, Marvell mvebu/kirkwood/orion, NXP i.MX/Vybrid
NXP LPC18xx, NXP LPC32xx, Renesas shmobile/r-mobile/r-car, Rockchips
rk3xxx, ST Ux500, ST STi, Atmel AT91/SAMA5, Altera SoCFPGA, Allwinner
Sunxi, Sigma Designs Tango, NVIDIA Tegra, Socionext Uniphier and ARM
Versatile Express.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Nx46
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"These are all the updates to device tree files for 32-bit platforms,
which as usual makes up the bulk of the ARM SoC changes: 462 non-merge
changesets, 450 files changed, 23340 insertions, 5216 deletions.
The three platforms that are added with the "soc" branch are here as
well, and we add some related machine files:
- For Aspeed AST2400/AST2500, we get the evaluation platform and the
Tyan Palmetto POWER8 mainboard that uses the AST2400 BMC
- For Oxnas 810SE, the Western Digital "My Book World Edition" is
added as the only platform at the moment.
- For ARM MPS2, the AN385 (Cortex-M3) and AN399 (Cortex-M7) are
supported
On the ARM Realview development platform, we now support all machines
with device tree, previously only the board files were supported,
which in turn will likely be removed soon.
Qualcomm IPQ4019 is the second generation ARM based "Internet
Processor", following the IPQ806x that is used in many high-end WiFi
routers. This one integrates two ath10k wifi radios that were
previously on separate chips.
Other boards that got added for existing chips are:
Ti OMAP family:
- Amazon Kindle Fire, first generation, tablet and ebook reader
- OnRISC Baltos iR 2110 and 3220 embedded industrial PCs
- TI AM5728 IDK, TI AM3359 ICE-V2, and TI DRA722 Rev C EVM
development systems
Samsung EXYNOS platform:
- Samsung ARTIK5 evaluation board, see
https://www.artik.io/modules/overview/artik-5/
NXP i.MX platforms:
- Ka-Ro electronics TX6S-8034, TX6S-8035, TX6U-8033, TX6U-81xx,
TX6Q-1036, TX6Q-1110/-1130, TXUL-0010 and TXUL-0011 industrial
SoM modules
- Embest MarS Board i.MX6Dual DIY platform
- Boundary Devices i.MX6 Quad Plus Nitrogen6_MAX and SoloX
Nitrogen6sx embedded boards
- Technexion Pico i.MX6UL compute module
- ZII VF610 Development Board
Marvell embedded (mvebu, orion, kirkwood) platforms:
- Linksys Viper (E4200v2 / EA4500) WiFi router
- Buffalo Kurobox Pro NAS
Qualcomm Snapdragon:
- Arrow DragonBoard 600c (96boards) with APQ8064 Snapdragon 600
Rockchips platform:
- mqmaker MiQi single-board computer
Altera SoCFPGA:
- samtec VIN|ING 1000 vehicle communication interface
Allwinner Sunxi platforms:
- Dserve DSRV9703C tablet
- Difrnce DIT4350 tablet
- Colorfly E708 Q1 tablet
- Polaroid MID2809PXE04 tablet
- Olimex A20 OLinuXino LIME2 single board computer
- Xunlong Orange Pi 2, Orange Pi One, and Orange Pi PC single board
computers
Across many platforms, bug fixes went in to address warnings that dtc
now emits with 'make dtbs W=1'. Further changes for device enablement
went into Ti OMAP, bcm283x (Raspberry Pi), bcm47xx (wifi router), Ti
Davinci, Samsung EXYNOS, Marvell mvebu/kirkwood/orion, NXP i.MX/Vybrid
NXP LPC18xx, NXP LPC32xx, Renesas shmobile/r-mobile/r-car, Rockchips
rk3xxx, ST Ux500, ST STi, Atmel AT91/SAMA5, Altera SoCFPGA, Allwinner
Sunxi, Sigma Designs Tango, NVIDIA Tegra, Socionext Uniphier and ARM
Versatile Express"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (458 commits)
ARM: dts: tango4: Import watchdog node
ARM: dts: tango4: Update cpus node for cpufreq
ARM: dts: tango4: Update DT to match clk driver
ARM: dts: tango4: Initial thermal support
arm/dst: Add Aspeed ast2500 device tree
arm/dts: Add Aspeed ast2400 device tree
ARM: sun7i: dt: Add pll3 and pll7 clocks
ARM: dts: sunxi: Add a olinuxino-lime2-emmc
ARM: dts: at91: sama5d4: add trng node
ARM: dts: at91: sama5d3: add trng node
ARM: dts: at91: sama5d2: add trng node
ARM: dts: at91: at91sam9g45 family: reduce the trng register map size
ARM: sun4i: dt: Add pll3 and pll7 clocks
ARM: sun5i: chip: Enable the TV Encoder
ARM: sun5i: r8: Add display blocks to the DTSI
ARM: sun5i: a13: Add display and TCON clocks
ARM: dts: ux500: configure the accelerometers open drain
ARM: mx5: dts: Enable USB OTG on M53EVK
ARM: dts: imx6ul-14x14-evk: Add audio support
ARM: dts: imx6qdl: Remove unneeded unit-addresses
...
Add AUXDATA needed to match the device-tree node for spi0 to the
non-device-tree clock.
Signed-off-by: David Lechner <david@lechnology.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
[nsekhar@ti.com: commit description updates]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Remove boilerplate code by using IRQCHIP_DECLARE macro.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
DA8X_NUM_UARTS not used in the code anywhere and should be determined
by DT anyway.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Take advantage of of_platoform_default_populate convience function.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add OF_DEV_AUXDATA entry for second i2c on the da850 DT board driver
to use i2c clock.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Some header files are never included outside of a mach-davinci
directory and do not need to be made visible in include/mach,
so let's just move them all down one level.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Init data marked const should be annotated with __initconst for
correctness and not __initdata. In some cases the array gathering
references to that data has to be marked const as well. This fixes
LTO builds that otherwise fail with section mismatch errors.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
of_device_ids (i.e. compatible strings and the respective data) are not
supposed to change at runtime. All functions working with of_device_ids
provided by <linux/of.h> work with const of_device_ids. So mark the
non-const structs in arch/arm as const, too.
While at it also add some __initconst annotations.
Acked-by: Jason Cooper <jason@lakedameon.net>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add OF_DEV_AUXDATA for mcasp to be able to use clocks.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
As we switch to use the watchdog core which permits more than one
active watchdog in the system, rename platform driver to
"davinci-wdt" to be identifiable.
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add OF_DEV_AUXDATA for ethernet davinci_emac driver in da850 board dt
file to use emac clock.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add OF_DEV_AUXDATA for mdio driver in da850 board dt
file to use mdio clock.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Serial clocks are enabled from of_platform_serial_setup:of_serial.c,
so remove davinci_serial_setup_clk from here.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
For modules having single clock, clk_get should be done with dev_id.
But current davinci implementation handles multiple instances
of the UART devices with single platform_device_register. Hence clk_get
is based on con_id rather than dev_id, this is not correct. Do
platform_device_register for each instance and clk_get on dev_id.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
[nsekhar@ti.com: actually stop using con_id in clk_get(), squash the
patch adding OF aux data into this one]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
These are mostly new device tree bindings for existing drivers, as well
as changes to the device tree source files to add support for those
devices, and a couple of new boards, most notably Samsung's Exynos5
based Chromebook.
The changes depend on earlier platform specific updates and touch
the usual platforms: omap, exynos, tegra, mxs, mvebu and davinci.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G60S
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates (part 2) from Arnd Bergmann:
"These are mostly new device tree bindings for existing drivers, as
well as changes to the device tree source files to add support for
those devices, and a couple of new boards, most notably Samsung's
Exynos5 based Chromebook.
The changes depend on earlier platform specific updates and touch the
usual platforms: omap, exynos, tegra, mxs, mvebu and davinci."
* tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: exynos: dts: cros5250: add EC device
ARM: dts: Add sbs-battery for exynos5250-snow
ARM: dts: Add i2c-arbitrator bus for exynos5250-snow
ARM: dts: add mshc controller node for Exynos4x12 SoCs
ARM: dts: Add chip-id controller node on Exynos4/5 SoC
ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
ARM: davinci: da850-evm: add SPI flash support
ARM: davinci: da850: override SPI DT node device name
ARM: davinci: da850: add SPI1 DT node
spi/davinci: add DT binding documentation
spi/davinci: no wildcards in DT compatible property
ARM: dts: mvebu: Convert mvebu device tree files to 64 bits
ARM: dts: mvebu: introduce internal-regs node
ARM: dts: mvebu: Convert all the mvebu files to use the range property
ARM: dts: mvebu: move all peripherals inside soc
ARM: dts: mvebu: fix cpus section indentation
ARM: davinci: da850: add EHRPWM & ECAP DT node
ARM/dts: OMAP3: fix pinctrl-single configuration
ARM: dts: Add OMAP3430 SDP NOR flash memory binding
ARM: dts: Add NOR flash bindings for OMAP2420 H4
...
This set of patches add support for remoteproc
used to control the DSP and also fix sparse
errors existing for quite some time.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=ldiG
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.10/soc-2-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/soc
From Sekhar Nori:
v3.10 SoC updates for DaVinci
This set of patches add support for remoteproc
used to control the DSP and also fix sparse
errors existing for quite some time.
* tag 'davinci-for-v3.10/soc-2-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: ensure global variables are declared
ARM: davinci: sram.c: fix incorrect type in assignment
ARM: davinci: da8xx dt: make file local symbols static
ARM: davinci: da8xx: add remoteproc support
Signed-off-by: Olof Johansson <olof@lixom.net>
Populate OF_DEV_AUXDATA with desired device name expected by spi-davinci
driver. Without this clk_get of spi-davinci DT driver fails.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Make some file-local functions static. This fixes the sparse
warnings:
CHECK arch/arm/mach-davinci/da8xx-dt.c
arch/arm/mach-davinci/da8xx-dt.c:23:13: warning: symbol 'da8xx_uart_clk_enable' was not declared. Should it be static?
arch/arm/mach-davinci/da8xx-dt.c:40:23: warning: symbol 'da850_auxdata_lookup' was not declared. Should it be static?
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add da850 EHRPWM & ECAP DT node along with pin-mux details.
Also adds OF_DEV_AUXDATA for EHRPWM & ECAP driver to use EHRPWM & ECAP
clock.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This pull request adds support for I2C0 and watchdog timer
for DA850 EVM booting using device tree. It also enables
machine reboot when using device tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=d1si
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.9/dt-2' of git://gitorious.org/linux-davinci/linux-davinci into next/dt
From Sekhar Nori:
Second round of DT updates for DaVinci.
This pull request adds support for I2C0 and watchdog timer
for DA850 EVM booting using device tree. It also enables
machine reboot when using device tree.
* tag 'davinci-for-v3.9/dt-2' of git://gitorious.org/linux-davinci/linux-davinci:
ARM: davinci: da850 DT: add support for machine reboot
ARM: davinci: da850: add wdt DT node
ARM: davinci: da850: add DT node for I2C0
Add I2C0 device tree and pin muxing information to da850-evm.
Also, add OF_DEV_AUXDATA for I2C0 controller driver in da850
board dt file to use I2C0 clock.
Verified i2c0 node gets created in sys class interface as
"/sys/class/i2c-dev/i2c-0/subsystem/i2c-0".
nsekhar@ti.com: tested using i2cdetect and i2cdump.
Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Now that the only field in struct sys_timer is .init, delete the struct,
and replace the machine descriptor .timer field with the initialization
function itself.
This will enable moving timer drivers into drivers/clocksource without
having to place a public prototype of each struct sys_timer object into
include/linux; the intent is to create a single of_clocksource_init()
function that determines which timer driver to initialize by scanning
the device dtree, much like the proposed irqchip_init() at:
http://www.spinics.net/lists/arm-kernel/msg203686.html
Includes mach-omap2 fixes from Igor Grinberg.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This board supports:
- AM1808 based board
- 64 MiB DDR ram
- 2 MiB Nor flash
- 128 MiB NAND flash
- use internal RTC
- I2C support
- hwmon lm75 support
- UBI/UBIFS support
- MMC support
- USB OTG support
This patch adds the basic DTS file enabling the serial ports.
Other features will be added in due course of time.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: davinci-linux-open-source@linux.davincidsp.com
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
[nsekhar@ti.com: modified after dtsi refactoring and added binding
documentation]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
David Lechner