New helper - sys_mmap_pgoff(); switch syscalls to using it.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
On MPC8572 and MPC8536 the status of GPIO pins configured
as output cannot be determined by reading GPDAT register.
Workaround by reading the status of input pins from GPDAT
and the status of output pins from a shadow register.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
gpiolib returns -ENXIO if struct gpio_chip::to_irq isn't set, so it's
safe to always call.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- Add nodes for PMC and GTM controllers. GTM4 can be used as a wakeup
source;
- Add fsl,magic-packet properties to eTSEC nodes, i.e. wake-on-lan
support. Unlike MPC8313 processors, MPC8315 can resume from deep
sleep upon magic packet reception.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We need to save SICRL, SICRH and SCCR registers on suspend, and restore
them on resume. Otherwise, we lose IO and clocks setup on MPC8315E-RDB
boards when ULPI USB PHY is used (non-POR setup).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Currently 83xx PMC driver clears deep_sleeping variable very early,
before devices are resumed. This makes fsl_deep_sleep() unusable in
drivers' resume() callback.
Sure, drivers can store fsl_deep_sleep() value on suspend and use
the stored value on resume. But a better solution is to postpone
clearing the deep_sleeping variable, i.e. move it into finish()
callback.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Port C interrupts can be either falling edge, or either edge.
Other external interrupts are either falling edge or active low.
Tested on a custom 8280 based board.
Signed-off-by: Mark Ware <mware@elphinstone.net>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Describe all LocalBus chipselects on MPC8349E-MITX board. Also add flash
bindings.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add OF descriptions of EEPROM, two GPIO extenders and SPD hanging on I2C
on this board.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
mpc8349 bears two GPIO controllers. Enable support for them.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It appears that we wrongly calculate dev_base for type1 config cycles.
The thing is: we shouldn't subtract hose->first_busno because PCI core
sets PCI primary, secondary and subordinate bus numbers, and PCIe
controller actually takes the registers into account. So we should use
just bus->number.
Also, according to MPC8315 reference manual, primary bus number should
always remain 0. We have PPC_INDIRECT_TYPE_SURPRESS_PRIMARY_BUS quirk
in indirect_pci.c, but since 83xx is somewhat special, it doesn't use
indirect_pci.c routines, so we have to implement the quirk specifically
for 83xx PCIe controllers.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
e821ea70f3 introduced a bug by copying
some 64-bit originated code as-is to be used by both 32 and 64-bit
but this code contains a 64-bit ony "cmpdi" instruction.
This changes it to cmpwi, which is fine since VRSAVE can only contains
a 32-bit value anyway.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@kernel.org>
At the moment when we EOI an interrupt we set the CPPR back to 0xFF
regardless of its previous value. This could lead to problems if we
take an interrupt with a priority of 5, but before EOIing it we get
an IPI which has a priority of 4. The problem is that at the moment
when we EOI the IPI we will set the CPPR to 0xFF, but it should
really be set back to 5 (the previous priority).
To keep track of the previous CPPR values we create the xics_cppr
structure that has an array for CPPR values and an index pointing
to the current priority. This can easily grow if new priorities get
added in the future.
This will also be useful because the partition adjunct option of
upcoming machines will update the H_XIRR hcall to accept the CPPR
as a parameter.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The recent patch to add cpu offline/online as part of the DLPAR
process for pseries causes a build break if CONFIG_SMP is not
defined. Original patch here;
http://lists.ozlabs.org/pipermail/linuxppc-dev/2009-November/078299.html
This corrects the build break by moving the online_node_cpus
and offline_node_cpus under the #ifdef CONFIG_ARCH_CPU_PROBE_RELEASE
portions of dlpar.c.
This patch also slightly modifies the online_node_cpus and offline_node_cpus
routines to prepend dlpar_ to the them and make them static. These two
routine are only used in the dlpar add/remove of cpus and these changes
should help clarify that.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Writing a driver using SCLPC on the MPC5200B I detected, that the
intspec arrays to map irqs to Linux virq cannot be const, because the
mapping and xlate functions only take non const pointers. All those
functions do not modify the intspec, so a const pointer could be used.
Signed-off-by: Roman Fietze <roman.fietze@telemotive.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use symbolic constant for PRESENT and avoid branching.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There is no need to do set the DIRTY bit directly in DTLB Error.
Trap to do_page_fault() and let the generic MM code do the work.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now that 8xx can fixup dcbX instructions, start using them
where possible like every other PowerPc arch do.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
8xx has not had WRITETHRU due to lack of bits in the pte.
After the recent rewrite of the 8xx TLB code, there are
two bits left. Use one of them to WRITETHRU.
Perhaps use the last SW bit to PAGE_SPECIAL or PAGE_FILE?
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
only DTLB Miss did set this bit, DTLB Error needs too otherwise
the setting is lost when the page becomes dirty.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is an assembler version to fixup DAR not being set
by dcbX, icbi instructions. There are two versions, one
uses selfmodifing code, the other uses a
jump table but is much bigger(default).
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
dcbz, dcbf, dcbi, dcbst and icbi do not set DAR when they
cause a DTLB Error. Dectect this by tagging DAR with 0x00f0
at every exception exit that modifies DAR.
Test for DAR=0x00f0 in DataTLBError and bail
to handle_page_fault().
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Update the TLB asm to make proper use of _PAGE_DIRY and _PAGE_ACCESSED.
Get rid of _PAGE_HWWRITE too.
Pros:
- I/D TLB Miss never needs to write to the linux pte.
- _PAGE_ACCESSED is only set on TLB Error fixing accounting
- _PAGE_DIRTY is mapped to 0x100, the changed bit, and is set directly
when a page has been made dirty.
- Proper RO/RW mapping of user space.
- Free up 2 SW TLB bits in the linux pte(add back _PAGE_WRITETHRU ?)
- kernel RO/user NA support.
Cons:
- A few more instructions in the TLB Miss routines.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
8xx sometimes need to load a invalid/non-present TLBs in
it DTLB asm handler.
These must be invalidated separaly as linux mm don't.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently the cpu-allocation/deallocation process comprises of two steps:
- Set the indicators and to update the device tree with DLPAR node
information.
- Online/offline the allocated/deallocated CPU.
This is achieved by writing to the sysfs tunables "probe" during allocation
and "release" during deallocation.
At the sametime, the userspace can independently online/offline the CPUs of
the system using the sysfs tunable "online".
It is quite possible that when a userspace tool offlines a CPU
for the purpose of deallocation and is in the process of updating the device
tree, some other userspace tool could bring the CPU back online by writing to
the "online" sysfs tunable thereby causing the deallocate process to fail.
The solution to this is to serialize writes to the "probe/release" sysfs
tunable with the writes to the "online" sysfs tunable.
This patch employs a mutex to provide this serialization, which is a no-op on
all architectures except PPC_PSERIES
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Acked-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently the cpu-allocation/deallocation on pSeries is a
two step process from the Userspace.
- Set the indicators and update the device tree by writing to the sysfs
tunable "probe" during allocation and "release" during deallocation.
- Online / Offline the CPUs of the allocated/would_be_deallocated node by
writing to the sysfs tunable "online".
This patch adds kernel code to online/offline the CPUs soon_after/just_before
they have been allocated/would_be_deallocated. This way, the userspace tool
that performs DLPAR operations would only have to deal with one set of sysfs
tunables namely "probe" and release".
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Acked-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Remove the CPU from the online map to prevent smp_call_function
from sending messages to a stopped CPU.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds the specific routines to probe and release (add and remove)
cpu resource for the powerpc pseries platform and registers these handlers
with the ppc_md callout structure.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Version 3 of this patch is updated with documentation added to
Documentation/ABI. There are no changes to any of the C code from v2
of the patch.
In order to support kernel DLPAR of CPU resources we need to provide an
interface to add (probe) and remove (release) the resource from the system.
This patch Creates new generic probe and release sysfs files to facilitate
cpu probe/release. The probe/release interface provides for allowing each
arch to supply their own routines for implementing the backend of adding
and removing cpus to/from the system.
This also creates the powerpc specific stubs to handle the arch callouts
from writes to the sysfs files.
The creation and use of these files is regulated by the
CONFIG_ARCH_CPU_PROBE_RELEASE option so that only architectures that need the
capability will have the files created.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The Dynamic Logical Partitioning capabilities of the powerpc pseries platform
allows for the addition and removal of resources (i.e. CPU's, memory, and PCI
devices) from a partition. The removal of a resource involves
removing the resource's node from the device tree and then returning the
resource to firmware via the rtas set-indicator call. To add a resource, it
is first obtained from firmware via the rtas set-indicator call and then a
new device tree node is created using the ibm,configure-coinnector rtas call
and added to the device tree.
This patch provides the kernel DLPAR infrastructure in a new filed named
dlpar.c. The functionality provided is for acquiring and releasing a resource
from firmware and the parsing of information returned from the
ibm,configure-connector rtas call. Additionally this exports the pSeries
reconfiguration notifier chain so that it can be invoked when device tree
updates are made.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The hotplug mediabay has tendrils deep into drivers/ide code
which makes a libata port reather difficult. In addition it's
ugly and could be done better.
This reworks the interface between the mediabay and the rest
of the world so that:
- Any macio_driver can now have a mediabay_event callback
which will be called when that driver sits on a mediabay and
it's been either plugged or unplugged. The device type is
passed as an argument. We can now move all the IDE cruft
into the IDE driver itself
- A check_media_bay() function can be used to take a peek
at the type of device currently in the bay if any, a cleaner
variant of the previous function with the same name.
- A pair of lock/unlock functions are exposed to allow the
IDE driver to block the hotplug callbacks during the initial
setup and probing of the bay in order to avoid nasty race
conditions.
- The mediabay code no longer needs to spin on the status
register of the IDE interface when it detects an IDE device,
this is done just fine by the IDE code itself
Overall, less code, simpler, and allows for another driver
than our old drivers/ide based one.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'timers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
timers, init: Limit the number of per cpu calibration bootup messages
posix-cpu-timers: optimize and document timer_create callback
clockevents: Add missing include to pacify sparse
x86: vmiclock: Fix printk format
x86: Fix printk format due to variable type change
sparc: fix printk for change of variable type
clocksource/events: Fix fallout of generic code changes
nohz: Allow 32-bit machines to sleep for more than 2.15 seconds
nohz: Track last do_timer() cpu
nohz: Prevent clocksource wrapping during idle
nohz: Type cast printk argument
mips: Use generic mult/shift factor calculation for clocks
clocksource: Provide a generic mult/shift factor calculation
clockevents: Use u32 for mult and shift factors
nohz: Introduce arch_needs_cpu
nohz: Reuse ktime in sub-functions of tick_check_idle.
time: Remove xtime_cache
time: Implement logarithmic time accumulation
* 'for-2.6.33' of git://git.kernel.dk/linux-2.6-block: (113 commits)
cfq-iosched: Do not access cfqq after freeing it
block: include linux/err.h to use ERR_PTR
cfq-iosched: use call_rcu() instead of doing grace period stall on queue exit
blkio: Allow CFQ group IO scheduling even when CFQ is a module
blkio: Implement dynamic io controlling policy registration
blkio: Export some symbols from blkio as its user CFQ can be a module
block: Fix io_context leak after failure of clone with CLONE_IO
block: Fix io_context leak after clone with CLONE_IO
cfq-iosched: make nonrot check logic consistent
io controller: quick fix for blk-cgroup and modular CFQ
cfq-iosched: move IO controller declerations to a header file
cfq-iosched: fix compile problem with !CONFIG_CGROUP
blkio: Documentation
blkio: Wait on sync-noidle queue even if rq_noidle = 1
blkio: Implement group_isolation tunable
blkio: Determine async workload length based on total number of queues
blkio: Wait for cfq queue to get backlogged if group is empty
blkio: Propagate cgroup weight updation to cfq groups
blkio: Drop the reference to queue once the task changes cgroup
blkio: Provide some isolation between groups
...
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c-stub: Documentation update
i2c-stub: Allow user to disable some commands
i2c-stub: Implement I2C block support
i2c: Refactor for_each callbacks
i2c-i801: Retry on lost arbitration
i2c: Remove big kernel lock from i2cdev_open
ics932s401: Clean up detect function
i2c: Simplify i2c_detect_address
i2c: Drop probe, ignore and force module parameters
i2c: Add missing __devinit markers to old i2c adapter drivers
i2c: Bus drivers don't have to support I2C_M_REV_DIR_ADDR
i2c: Prevent priority inversion on top of bus lock
i2c-voodoo3: Delete
i2c-powermac: Drop temporary name buffer
i2c-powermac: Include the i2c_adapter in struct pmac_i2c_bus
i2c-powermac: Log errors
i2c-powermac: Refactor i2c_powermac_smbus_xfer
i2c-powermac: Reject unsupported I2C transactions
i2c/chips: Move ds1682 to drivers/misc
* 'kvm-updates/2.6.33' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (84 commits)
KVM: VMX: Fix comparison of guest efer with stale host value
KVM: s390: Fix prefix register checking in arch/s390/kvm/sigp.c
KVM: Drop user return notifier when disabling virtualization on a cpu
KVM: VMX: Disable unrestricted guest when EPT disabled
KVM: x86 emulator: limit instructions to 15 bytes
KVM: s390: Make psw available on all exits, not just a subset
KVM: x86: Add KVM_GET/SET_VCPU_EVENTS
KVM: VMX: Report unexpected simultaneous exceptions as internal errors
KVM: Allow internal errors reported to userspace to carry extra data
KVM: Reorder IOCTLs in main kvm.h
KVM: x86: Polish exception injection via KVM_SET_GUEST_DEBUG
KVM: only clear irq_source_id if irqchip is present
KVM: x86: disallow KVM_{SET,GET}_LAPIC without allocated in-kernel lapic
KVM: x86: disallow multiple KVM_CREATE_IRQCHIP
KVM: VMX: Remove vmx->msr_offset_efer
KVM: MMU: update invlpg handler comment
KVM: VMX: move CR3/PDPTR update to vmx_set_cr3
KVM: remove duplicated task_switch check
KVM: powerpc: Fix BUILD_BUG_ON condition
KVM: VMX: Use shared msr infrastructure
...
Trivial conflicts due to new Kconfig options in arch/Kconfig and kernel/Makefile
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1815 commits)
mac80211: fix reorder buffer release
iwmc3200wifi: Enable wimax core through module parameter
iwmc3200wifi: Add wifi-wimax coexistence mode as a module parameter
iwmc3200wifi: Coex table command does not expect a response
iwmc3200wifi: Update wiwi priority table
iwlwifi: driver version track kernel version
iwlwifi: indicate uCode type when fail dump error/event log
iwl3945: remove duplicated event logging code
b43: fix two warnings
ipw2100: fix rebooting hang with driver loaded
cfg80211: indent regulatory messages with spaces
iwmc3200wifi: fix NULL pointer dereference in pmkid update
mac80211: Fix TX status reporting for injected data frames
ath9k: enable 2GHz band only if the device supports it
airo: Fix integer overflow warning
rt2x00: Fix padding bug on L2PAD devices.
WE: Fix set events not propagated
b43legacy: avoid PPC fault during resume
b43: avoid PPC fault during resume
tcp: fix a timewait refcnt race
...
Fix up conflicts due to sysctl cleanups (dead sysctl_check code and
CTL_UNNUMBERED removed) in
kernel/sysctl_check.c
net/ipv4/sysctl_net_ipv4.c
net/ipv6/addrconf.c
net/sctp/sysctl.c
* git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/sysctl-2.6: (43 commits)
security/tomoyo: Remove now unnecessary handling of security_sysctl.
security/tomoyo: Add a special case to handle accesses through the internal proc mount.
sysctl: Drop & in front of every proc_handler.
sysctl: Remove CTL_NONE and CTL_UNNUMBERED
sysctl: kill dead ctl_handler definitions.
sysctl: Remove the last of the generic binary sysctl support
sysctl net: Remove unused binary sysctl code
sysctl security/tomoyo: Don't look at ctl_name
sysctl arm: Remove binary sysctl support
sysctl x86: Remove dead binary sysctl support
sysctl sh: Remove dead binary sysctl support
sysctl powerpc: Remove dead binary sysctl support
sysctl ia64: Remove dead binary sysctl support
sysctl s390: Remove dead sysctl binary support
sysctl frv: Remove dead binary sysctl support
sysctl mips/lasat: Remove dead binary sysctl support
sysctl drivers: Remove dead binary sysctl support
sysctl crypto: Remove dead binary sysctl support
sysctl security/keys: Remove dead binary sysctl support
sysctl kernel: Remove binary sysctl logic
...
This adds dma_parms to macio devices and initializes them with
default values. This will allow pata_macio to setup the appropriate
max segment size for the block layer.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds some basic devres support. When enabled via macio_enable_devres()
resources requested by drivers will be automatically released.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently userspace has no chance to find out which virtual address space we're
in and resolve addresses. While that is a big problem for migration, it's also
unpleasent when debugging, as gdb and the monitor don't work on virtual
addresses.
This patch exports enough of the MMU segment state to userspace to make
debugging work and thus also includes the groundwork for migration.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit a0668cdc15 cleans up the handling
of kmem_caches for allocating various levels of pagetables.
Unfortunately, it conflicts badly with CONFIG_PPC_SUBPAGE_PROT, due to
the latter's cleverly hidden technique of adding some extra allocation
space to the top level page directory to store the extra information
it needs.
Since that extra allocation really doesn't fit into the cleaned up
page directory allocating scheme, this patch alters
CONFIG_PPC_SUBPAGE_PROT to instead allocate its struct
subpage_prot_table as part of the mm_context_t.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Include the i2c_adapter in struct pmac_i2c_bus. This avoids memory
fragmentation and allows for several code cleanups.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Michel Daenzer <michel@daenzer.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (63 commits)
x86, Calgary IOMMU quirk: Find nearest matching Calgary while walking up the PCI tree
x86/amd-iommu: Remove amd_iommu_pd_table
x86/amd-iommu: Move reset_iommu_command_buffer out of locked code
x86/amd-iommu: Cleanup DTE flushing code
x86/amd-iommu: Introduce iommu_flush_device() function
x86/amd-iommu: Cleanup attach/detach_device code
x86/amd-iommu: Keep devices per domain in a list
x86/amd-iommu: Add device bind reference counting
x86/amd-iommu: Use dev->arch->iommu to store iommu related information
x86/amd-iommu: Remove support for domain sharing
x86/amd-iommu: Rearrange dma_ops related functions
x86/amd-iommu: Move some pte allocation functions in the right section
x86/amd-iommu: Remove iommu parameter from dma_ops_domain_alloc
x86/amd-iommu: Use get_device_id and check_device where appropriate
x86/amd-iommu: Move find_protection_domain to helper functions
x86/amd-iommu: Simplify get_device_resources()
x86/amd-iommu: Let domain_for_device handle aliases
x86/amd-iommu: Remove iommu specific handling from dma_ops path
x86/amd-iommu: Remove iommu parameter from __(un)map_single
x86/amd-iommu: Make alloc_new_range aware of multiple IOMMUs
...
The stanza for PCI was copied from Bamboo which has four PCI slots. Yosemite
only has one PCI slot which is mapped to IDSEL 12, ADDR 22, IRQ2 Vector 25,
INTA.
Signed-off-by: Curtis Wald <cwald@watchguardvideo.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Set PCI-E node inbound DMA ranges size to 4GB for correct boot up of Katmai.
Signed-off-by: Pravin Bathija <pbathija@amcc.com>
Acked-by: Feng Kan <fkan@amcc.com>
Acked-by: Prodyut Hazarika <phazarika@amcc.com>
Acked-by: Loc Ho <lho@amcc.com>
Acked-by: Tirumala Reddy Marri <tmarri@amcc.com>
Acked-by: Victor Gallardo <vgallardo@amcc.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The old BUILD_BUG_ON implementation didn't work with __builtin_constant_p().
Fixing that revealed this test had been inverted for a long time without
anybody noticing...
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
X86 CPUs need to have some magic happening to enable the virtualization
extensions on them. This magic can result in unpleasant results for
users, like blocking other VMMs from working (vmx) or using invalid TLB
entries (svm).
Currently KVM activates virtualization when the respective kernel module
is loaded. This blocks us from autoloading KVM modules without breaking
other VMMs.
To circumvent this problem at least a bit, this patch introduces on
demand activation of virtualization. This means, that instead
virtualization is enabled on creation of the first virtual machine
and disabled on destruction of the last one.
So using this, KVM can be easily autoloaded, while keeping other
hypervisors usable.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This reverts commit c045256d14.
It breaks build when CONFIG_PPC_SUBPAGE_PROT is not set. I will
commit a fixed version separately
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Code was added to mm/higmem.c that depends on several
kmap types that powerpc does not support. We add dummy
invalid definitions for KM_NMI, KM_NM_PTE, and KM_IRQ_PTE.
According to list discussion, this fix should not be needed
anymore starting with 2.6.33. The code is commented to this
effect so hopefully we will remember to remove this.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit a4fe3ce769 introduced a new
get_user_pages() path for hugepages on powerpc. Unfortunately, there
is a bug in it's loop logic, which can cause it to overrun the end of
the intended region. This came about by copying the logic from the
normal page path, which assumes the address and end parameters have
been pagesize aligned at the top-level. Since they're not *hugepage*
size aligned, the simplistic logic could step over the end of the gup
region without triggering the loop end condition.
This patch fixes the bug by using the technique that the normal page
path uses in levels above the lowest to truncate the ending address to
something we know we'll match with.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit a0668cdc15 cleans up the handling
of kmem_caches for allocating various levels of pagetables.
Unfortunately, it conflicts badly with CONFIG_PPC_SUBPAGE_PROT, due to
the latter's cleverly hidden technique of adding some extra allocation
space to the top level page directory to store the extra information
it needs.
Since that extra allocation really doesn't fit into the cleaned up
page directory allocating scheme, this patch alters
CONFIG_PPC_SUBPAGE_PROT to instead allocate its struct
subpage_prot_table as part of the mm_context_t.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Mtdblock driver doesn't call flush_dcache_page for pages in request. So,
this causes problems on architectures where the icache doesn't fill from
the dcache or with dcache aliases. The patch fixes this.
The ARCH_IMPLEMENTS_FLUSH_DCACHE_PAGE symbol was introduced to avoid
pointless empty cache-thrashing loops on architectures for which
flush_dcache_page() is a no-op. Every architecture was provided with this
flush pages on architectires where ARCH_IMPLEMENTS_FLUSH_DCACHE_PAGE is
equal 1 or do nothing otherwise.
See "fix mtd_blkdevs problem with caches on some architectures" discussion
on LKML for more information.
Signed-off-by: Ilya Loginov <isloginov@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Peter Horton <phorton@bitbox.co.uk>
Cc: "Ed L. Cashin" <ecashin@coraid.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Commit 87ec0e98cf in kumar's next branch
broke one of my test configs since it looks like Anton forgot about
that mpc832x_rdb platform which still uses the old style probing for
the SPI stuff.
I'll let them do a cleaner fix that probably involves changing the
probing method and getting rid of the platform device but for now
this will do to fix it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch was submitted, discussed, and eventually Acked by everyone, yet
still isn't in the tree. See:
http://patchwork.ozlabs.org/patch/1240/
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Cc: Arnd Bergmann <arnd@anrdb.de>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Code was added to mm/higmem.c that depends on several
kmap types that powerpc does not support. We add dummy
invalid definitions for KM_NMI, KM_NM_PTE, and KM_IRQ_PTE.
According to list discussion, this fix should not be needed
anymore starting with 2.6.33. The code is commented to this
effect so hopefully we will remember to remove this.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We can kill unused swiotlb variable.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since they are static inline functions.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The code under "if (is_global_init())" is bogus, and is_global_init()
itself is not right in mt case.
Contrary to what the comment says, nowadays force_sig_info() does kill
init even if the handler is SIG_DFL. Note that force_sig_info() clears
SIGNAL_UNKILLABLE exactly for this case.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When a CPU is offlined on POWER currently, we call rtas_stop_self() and hand
the CPU back to the resource pool. This path is used for DLPAR which will
cause a change in the LPAR configuration which will be visible outside.
This patch changes the default state a CPU is put into when it is offlined.
On platforms which support ceding the processor to the hypervisor with
latency hint specifier value, during a cpu offline operation,
instead of calling rtas_stop_self(), we cede the vCPU to the hypervisor
while passing a latency hint specifier value. The Hypervisor can use this hint
to provide better energy savings. Also, during the offline
operation, the control of the vCPU remains with the LPAR as oppposed to
returning it to the resource pool.
The patch achieves this by creating an infrastructure to set the
preferred_offline_state() which can be either
- CPU_STATE_OFFLINE: which is the current behaviour of calling
rtas_stop_self()
- CPU_STATE_INACTIVE: which cedes the vCPU to the hypervisor with the latency
hint specifier.
The codepath which wants to perform a DLPAR operation can set the
preferred_offline_state() of a CPU to CPU_STATE_OFFLINE before invoking
cpu_down().
The patch also provides a boot-time command line argument to disable/enable
CPU_STATE_INACTIVE.
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch provides an extended_cede_processor() helper function
which takes the cede latency hint as an argument. This hint is to be passed
on to the hypervisor to cede to the corresponding state on platforms
which support it.
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Arun R Bharadwaj <arun@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Move ehea hcall definitions into hvcall.h.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The typename member of struct irq_chip was kept for migration purposes
and is obsolete since more than 2 years. Fix up the leftovers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@ozlabs.org
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
SPIN_LOCK_UNLOCKED is deprecated. Init the lock array at runtime
instead.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@ozlabs.org
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The ioctl is only used for powermac systems and reads a partition
number from an array which is initialized at boot time way before the
nvram code is initialized. So it's safe to switch to unlocked_ioctl.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
size_t len cannot be less than 0.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add basic support for the P4080 DS reference board. None of the data
path devices (ethernet, crypto, pme) are support at this time.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for NVRAM on GE Fanuc's PPC9A.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for NVRAM on GE Fanuc's SBC310.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch enables the NVRAM found on the GE Fanuc SBC610
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Re-write the code so its more standalone and fixed some issues:
* Bump'd # of CAM entries to 64 to support e500mc
* Make the code handle MAS7 properly
* Use pr_cont instead of creating a string as we go
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For consistency drop & in front of every proc_handler. Explicity
taking the address is unnecessary and it prevents optimizations
like stubbing the proc_handlers to NULL.
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
* 'hostprogs-wmissing-prototypes' of git://git.kernel.org/pub/scm/linux/kernel/git/josh/linux-misc:
Makefile: Add -Wmising-prototypes to HOSTCFLAGS
oss: Mark loadhex static in hex2hex.c
dtc: Mark various internal functions static
dtc: Set "noinput" in the lexer to avoid an unused function
drm: radeon: Mark several functions static in mkregtable
arch/sparc/boot/*.c: Mark various internal functions static
arch/powerpc/boot/addRamDisk.c: Mark several internal functions static
arch/alpha/boot/tools/objstrip.c: Mark "usage" static
Documentation/vm/page-types.c: Declare checked_open static
genksyms: Mark is_reserved_word static
kconfig: Mark various internal functions static
kconfig: Make zconf.y work with current bison
Since commit 0a544198 "timekeeping: Move NTP adjusted clock multiplier
to struct timekeeper" the clock multiplier of vsyscall is updated with
the unmodified clock multiplier of the clock source and not with the
NTP adjusted multiplier of the timekeeper.
This causes user space observerable time warps:
new CLOCK-warp maximum: 120 nsecs, 00000025c337c537 -> 00000025c337c4bf
Add a new argument "mult" to update_vsyscall() and hand in the
timekeeping internal NTP adjusted multiplier.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Cc: "Zhang Yanmin" <yanmin_zhang@linux.intel.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Tony Luck <tony.luck@intel.com>
LKML-Reference: <1258436990.17765.83.camel@minggr.sh.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Resolve the conflict between v2.6.32-rc7 where dn_def_dev_handler
gets a small bug fix and the sysctl tree where I am removing all
sysctl strategy routines.
Nothing outside of arch/powerpc/boot/addRamDisk.c references the
functions "get4k", "put4k", or "death".
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
powerpc grew a new warning due to the type change of clockevent->mult.
The architectures which use parts of the generic time keeping
infrastructure tripped over my wrong assumption that
clocksource_register is only used when GENERIC_TIME=y.
I should have looked and also I should have known better. These
renitent Gaul villages are racking my nerves. Some serious deprecating
is due.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Merge the WDT code into the GPT interface.
Signed-off-by: Albrecht Dreß <albrecht.dress@arcor.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch changes the period parameter of mpc52xx_gpt_start_timer to
a u64 to support larger timeout periods.
Signed-off-by: Albrecht Dreß <albrecht.dress@arcor.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Now that sys_sysctl is a generic wrapper around /proc/sys .ctl_name
and .strategy members of sysctl tables are dead code. Remove them.
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Export is needed for modular builds, and a static inline stub is needed
for non-MPC83xx builds.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Simply add power management controller nodes and sleep properties.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds needed nodes and properties to support suspend/resume
on the MPC8610HPCD boards.
There is a dedicated switch (SW9) that is used to wake up the boards.
By default the SW9 button is routed to IRQ8, but could be re-routed
(via PIXIS) to sreset.
With 'no_console_suspend' kernel command line argument specified, the
board is also able to wakeup upon serial port input.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com> [dts]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- Add power management controller nodes;
- Add interrupts for RTC nodes, the RTC interrupt may be used as a
wakeup source;
- Add sleep properties (DEVDISR bit mask) and sleep-nexus nodes.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds suspend/resume support for MPC8540 and MPC8641D-
compatible CPUs. To reach sleep state, we just write the SLP bit
into the PM control and status register.
So far we don't support Deep Sleep mode as found in newer MPC85xx
CPUs (i.e. MPC8536). It can be relatively easy implemented though,
and for it we reserve 'mem' suspend type.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
So far the driver is used to reset QE upon resume, which is needed on
85xx. Later we can move some QE initialization steps into probe().
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is needed to avoid ugly #ifdefs in drivers. Also update fsl_qe_udc
driver so that now it doesn't define its own versions that cause build
breakage when the generic stubs are used.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The bits are generic to CPM devices, so let's move them to the
common header file, so drivers won't need to privately reintroduce
another bunch of the same bits (as we can't include cpm2.h header
together with cpm1.h).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
struct mcc defined in both immap_qe.h and immap_cpm2.h, so they will
conflic when included in a single file. The mcc struct is easy to deal
with, since it isn't used in any driver (yet), so let's just rename QE
version to qe_mcc.
The ucb_ctlr is a bit trickier, since it is used by fsl_qe_udc driver,
and the driver supports both CPM and QE UDCs, plus the QE version is
used to form a bigger immap struct.
I don't want to touch too much of USB code in this series, so for now
let's just copy most generic version into the common cpm.h header,
later we'll create cpm_usb.h where we'll place common USB structs that
are used by QE/CPM UDC and QE Host drivers (FHCI).
And as for the structs in qe.h and cpm2.h, just prefix them with qe_
and cpm_.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When cpm2.h included into spi_mpc8xxx driver, the SPI defines
in the header conflict with defines in the driver.
We don't need them in the header file, so remove them. Plus
remove "struct spi", we'll use a better version in the driver.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1020 is another member of Freescale QorIQ series of processors.
It is an e500 based dual core SOC.
Being a scaled down version of P2020 it has following differences from P2020:
- 533MHz - 800MHz core frequency.
- 256Kbyte L2 cache
- Ethernet controllers with classification capabilities(new controller).
From board perspective P1020RDB is same as P2020RDB.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It appears that QE shuts down on all MPC85xx CPUs (i.e. MPC8568 and
MPC8569) and thus needs reset upon resume.
So modify qe_alive_during_sleep() to account that.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For MPC8569 CPUs we'll need to reset QE after each suspend, so make
qe_reset() code path suitable for repeated invocation, that is:
- Don't initialize rheap structures if already initialized;
- Don't allocate muram for SDMA if already allocated, just reinitialize
registers with previously allocated muram offset;
- Remove __init attributes from qe_reset() and cpm_muram_init();
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch creates the dts files for each core and splits the devices
between the two cores for P2020RDB.
core0 has memory, L2, i2c, spi, dma1, usb, eth0, eth1, crypto,
global-util, pci0,
core1 has L2, dma2, eth0, pci1, msi.
MPIC is shared between two cores but each core will protect its
interrupts from other core by using "protected-sources" of mpic.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is needed to avoid #ifdefs in MPC85xx suspend/resume code.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MPC8569 CPUs have four QE RISCs, so we need to increase MAX_QE_RISC
constant, otherwise qe_upload_firmware() fails at sanity checking.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
pasemi_defconfig hasn't been updated for a year.
Mostly a refresh of defaults, but this also disables 64K pages.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This enables us to avoid printing swiotlb memory info when we
initialize swiotlb. After swiotlb initialization, we could find
that we don't need swiotlb.
This patch removes the code to print swiotlb memory info in
swiotlb_init() and exports the function to do that.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: chrisw@sous-sol.org
Cc: dwmw2@infradead.org
Cc: joerg.roedel@amd.com
Cc: muli@il.ibm.com
Cc: tony.luck@intel.com
Cc: benh@kernel.crashing.org
LKML-Reference: <1257849980-22640-9-git-send-email-fujita.tomonori@lab.ntt.co.jp>
[ -v2: merge up conflict ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
something-bility is spelled as something-blity
so a grep for 'blit' would find these lines
this is so trivial that I didn't split it by subsystem / copy
additional maintainers - all changes are to comments
The only purpose is to get fewer false positives when grepping
around the kernel sources.
Signed-off-by: Dirk Hohndel <hohndel@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This uses compat_alloc_userspace to remove the various
hacks to allow do_sysctl to write to throuh oldlenp.
The rest of our mature compat syscall helper facitilies
are used as well to ensure we have a nice clean maintainable
compat syscall that can be used on all architectures.
The motiviation for a generic compat sysctl (besides the
obvious hack removal) is to reduce the number of compat
sysctl defintions out there so I can refactor the
binary sysctl implementation.
ppc already used the name compat_sys_sysctl so I remove the
ppcs version here.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
u-boot partition size should be 0x80000 (512 KB), not 0x8000 (32 KB).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch fixes USB GPIOs numbers for MPC8569E-MDS boards, plus
according to the latest HW Getting Started Guide (rev 3.3, pilot
boards), USB "POWER" GPIO polarity has changed, it is no longer
inverted.
This patch makes USB Host somewhat work on pilot boards, though
there are still some problems with determining devices speed and
long bulk transfers.
Reported-by: Liu Yu <Yu.Liu@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Prevent NULL dereference if kmalloc() fails. Also clean up if
of_mdiobus_register() returns an error.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The PCI-e addressing was originally patterned of the MPC8548CDS
which has PCI1, PCI2, and PCI-e. Since this board only has
PCI1 and PCI-e, it makes more sense to be similar to the MPC8568MDS
board. This does that by cutting the PCI/PCI-e I/O sizes from
16MB to 8MB and pulling the PCI-e I/O range back to 0xe280_0000
(the hole where PCI2 I/O would have been).
This also fixes a typo where an extra zero made an 8MB range a 128MB
range, removes the hole left by PCI2 from the aliases, and sets the
clocks to match the oscillators that are actually on the board.
With accompanying u-boot updates, PCI-e has been validated with
both a sky2 card (1148:9e00) and an e1000 card (8086:108b).
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Patch f598282f51 exposed a problem in
powerpc MSI-X functionality, making network interfaces such as ixgbe
and cxgb3 stop to work when MSI-X is enabled. RX interrupts were not
being generated.
The problem was caused because MSI irq was not being effectively
unmasked after device initialization.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Doing so causes xtime to be negative which crashes the timekeeping
code in funny ways when doing suspend/resume
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Following S390's good example we should use hrtimers for the decrementer too!
This patch converts the timer from the old mechanism to hrtimers.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It looks like the variable "pc" is defined. At least the current code always
failed on me stating that "pc" is already defined somewhere else.
Let's use _pc instead, because that doesn't collide.
Is this the right approach? Does it break on 440 too? If not, why not?
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now we have everything in place to be able to build KVM, so let's add it
as config option and in the Makefile.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In order to access fields in the PACA from assembly code, we need
to generate offsets using asm-offsets.c.
So let's add the new PACA related bits, we just introduced!
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For KVM we need to store some information in the PACA, so we
need to extend it.
This patch adds KVM SLB shadow related entries to the PACA and
a field that indicates if we're inside a guest.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
To be able to keep KVM as module, we need to export the SLB trampoline
addresses to the module, so it knows where to jump to.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For KVM we need to allocate a new context id, but don't really care about
all the mm context around it.
So let's split the alloc and destroy functions for the context id, so we can
grab one without allocating an mm context.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We want to be able to build KVM as a module. To enable us doing so, we
need some more exports from core Linux parts.
This patch exports all functions and variables that are required for KVM.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need to access some VCPU fields from assembly code. In order to get
the proper offsets, we have to define them in asm-offsets.c.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need to run some KVM trampoline code in real mode. Unfortunately, real mode
only covers 8MB on Cell so we need to squeeze ourselves as low as possible.
Also, we need to trap interrupts to get us back from guest state to host state
without telling Linux about it.
This patch adds interrupt traps and includes the KVM code that requires real
mode in the real mode parts of Linux.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Little opcodes behave differently on desktop and embedded PowerPC cores.
In order to reflect those differences, let's add some #ifdef code to emulate.c.
We could probably also handle them in the core specific emulation files, but I
would prefer to reuse as much code as possible.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We support setting the DEC to a certain value right now. Doing that basically
triggers the CPU local timer.
But there's also an mfdec command that enabled the OS to read the decrementor.
This is required at least by all desktop and server PowerPC Linux kernels. It
can't really hurt to allow embedded ones to do it as well though.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There are generic parts of PowerPC that can be shared across all
implementations and specific parts that only apply to BookE or desktop PPCs.
This patch adds emulation for desktop specific opcodes that don't apply
to BookE CPUs.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds an implementation for a G3/G4 MMU, so we can run G3 and
G4 guests in KVM on Book3s_64.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
To be able to run a guest, we also need to implement a guest MMU.
This patch adds MMU handling for Book3s_64 guests.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We designed the Book3S port of KVM as modular as possible. Most
of the code could be easily used on a Book3S_32 host as well.
The main difference between 32 and 64 bit cores is the MMU. To keep
things well separated, we treat the book3s_64 MMU as one possible compile
option.
This patch adds all the MMU helpers the rest of the code needs in
order to modify the host's MMU, like setting PTEs and segments.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds the book3s core handling file. Here everything that is generic to
desktop PowerPC cores is handled, including interrupt injections, MSR settings,
etc.
It basically takes over the same role as booke.c for embedded PowerPCs.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Al Viro