Handled NCQ errors in the low level driver as the FW
is not providing the faulty tag for NCQ errors for libsas
to recover.
[jejb: fix checkpatch issues]
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Individual WWN read operations based on controller.
PM8081 - Read WWN from Flash VPD.
PM8088/89 - Read WWN from EEPROM.
PM8001 - Read WWN from NVM.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Changed name in driver to pm80xx. Updated debug messages.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Performing pci_free_consistent in tasklet had result in a core dump. So
allocated a new memory region for it. Fix for passing proper address
and operation in firmware flash update.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Additional bar shift for new SPC firmware, applicable to device
id 0x8081 only.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Implementation of SPCv/ve specific hardware functionality and
macros. Changing common functionalities wrt SPCv/ve operations.
Conditional checks for SPC specific operations.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Implementation of interrupt handlers and tasklets to support
upto 64 interrupt for the device.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Update of function prototype for common function to SPC and SPCv/ve.
Multiple queues implementation for IO.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Memory allocation and configuration of multiple inbound and
outbound queues.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Updated pci id table with device, vendor, subdevice and subvendor ids
for 8081, 8088, 8089 SAS/SATA controllers. Added SPCv/ve related macros.
Updated macros, hba info structure and other structures for SPCv/ve.
Update of structure and variable names for SPC hardware functionalities.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
All memory regions are allocated based on variables total_len
and alignment but free was based on element_size.
Signed-off-by: Sakthivel K <DL.Team.PMC.SPC.Linux.open.source@pmcs.com>
Signed-off-by: Anand Kumar S <DL.Team.PMC.SPC.Linux.open.source@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Adam Radford <linuxraid@lsi.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The timer and the completion are only used for slow path tasks (smp, and
lldd tmfs), yet we incur the allocation space and cpu setup time for
every fast path task.
Cc: Xiangliang Yu <yuxiangl@marvell.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
sas_eh_bus_reset_handler() amounts to sas_phy_reset() without
notification of the reset to the lldd. If this is triggered from
eh-cmnd recovery there may be sas_tasks for the lldd to terminate, so
->lldd_I_T_nexus_reset is warranted.
Cc: Xiangliang Yu <yuxiangl@marvell.com>
Cc: Luben Tuikov <ltuikov@yahoo.com>
Cc: Jack Wang <jack_wang@usish.com>
Reviewed-by: Jacek Danecki <jacek.danecki@intel.com>
[jacek: modify pm8001_I_T_nexus_reset to return -ENODEV]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This is a followup to a patch provided by Jack Wang on September 21 2011.
After increasing the CAN_QUEUE to 510 in pm8001 we discovered some performance
degredation from time to time. We needed to increase the MPI queue to
compensate and ensure we never hit that limit. We also needed to double
the margin to support event and administrivial commands that take from
the pool resulting in an occasional largely unproductive command completion
with soft error to the caller when the command pool is overloaded temporarily.
Signed-off-by: Mark Salyzyn <mark_salyzyn@xyratex.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Data type of the 'tag' field of 'fw_flash_Update_resp' should be __le32.
Data type of 'pHeader' should be __le32. Remove 2nd cast to 'piomb'.
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPdrIWAAoJEDeqqVYsXL0Mny4IAMTzXGOXCykpWhdIe2R8w0Ys
eIoTJhBKoQWnLTV8cOODtwmtZcoQLeXkZmizZiAJvX6O1tOgueg+W4AFa9grxXGI
O0d1bSb2ardzU7VZrZSY60Hd4bylMwn4Xv/0dRrQMwTJO0LEeGWsJPV2+2BuXwMB
lGCNB67oUBXgMOI1jUZQRwx/mBzQ3e/gINjnpZTNKHia7YkX/yVTFISq7htgfDN7
1wRGxymbHtVap3NbtUO96BUUndAiF5vom+4WNvaQUyPrCc6aoGWjv+J9DQXY/zgv
AYjujAluK396D6YncGFAWBzYOg9WFbq54v0PRUanjcTTAu5ILs2BxqWdhmnvl14=
=IH8T
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
Pull SCSI updates from James Bottomley:
"This is primarily another round of driver updates (lpfc, bfa, fcoe,
ipr) plus a new ufshcd driver. There shouldn't be anything
controversial in here (The final deletion of scsi proc_ops which
caused some build breakage has been held over until the next merge
window to give us more time to stabilise it).
I'm afraid, with me moving continents at exactly the wrong time,
anything submitted after the merge window opened has been held over to
the next merge window."
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (63 commits)
[SCSI] ipr: Driver version 2.5.3
[SCSI] ipr: Increase alignment boundary of command blocks
[SCSI] ipr: Increase max concurrent oustanding commands
[SCSI] ipr: Remove unnecessary memory barriers
[SCSI] ipr: Remove unnecessary interrupt clearing on new adapters
[SCSI] ipr: Fix target id allocation re-use problem
[SCSI] atp870u, mpt2sas, qla4xxx use pci_dev->revision
[SCSI] fcoe: Drop the rtnl_mutex before calling fcoe_ctlr_link_up
[SCSI] bfa: Update the driver version to 3.0.23.0
[SCSI] bfa: BSG and User interface fixes.
[SCSI] bfa: Fix to avoid vport delete hang on request queue full scenario.
[SCSI] bfa: Move service parameter programming logic into firmware.
[SCSI] bfa: Revised Fabric Assigned Address(FAA) feature implementation.
[SCSI] bfa: Flash controller IOC pll init fixes.
[SCSI] bfa: Serialize the IOC hw semaphore unlock logic.
[SCSI] bfa: Modify ISR to process pending completions
[SCSI] bfa: Add fc host issue lip support
[SCSI] mpt2sas: remove extraneous sas_log_info messages
[SCSI] libfc: fcoe_transport_create fails in single-CPU environment
[SCSI] fcoe: reduce contention for fcoe_rx_list lock [v2]
...
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPZxSnAAoJEDeqqVYsXL0M0Y4IAMX0vrTVZbg6psA5/gMcWGRP
CkFXEQ8n0PL2SCaj6BoDqamJFe5Nc7dnqxM0fGawB4S9vr3rHhiOlwO+NbV9zFYC
2skBTpeL3sjgtN/jTBdfeeAa7xTYpu/XGyei0NS1A5c2AyMVXV0uYV2s4VNZxe44
tVIn1OEzM2giZ9EB1OZslDMrg5XXm3MBIUECP0LbWUhBm/35caSFKzMXRwhh7WiK
+AVmc2AZYtdEwuknDyiH7KlsaoB3vGL9pPrAUJzIgEhy2pOo2A7W72HfA4Fj+y6a
uF9HBS5zciMp1+sGWry62AjNbWgin9BRlozBEO/lJhIfMGDV1nXEIJsOkOgkdoE=
=1TxB
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
SCSI updates from James Bottomley:
"The update includes the usual assortment of driver updates (lpfc,
qla2xxx, qla4xxx, bfa, bnx2fc, bnx2i, isci, fcoe, hpsa) plus a huge
amount of infrastructure work in the SAS library and transport class
as well as an iSCSI update. There's also a new SCSI based virtio
driver."
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (177 commits)
[SCSI] qla4xxx: Update driver version to 5.02.00-k15
[SCSI] qla4xxx: trivial cleanup
[SCSI] qla4xxx: Fix sparse warning
[SCSI] qla4xxx: Add support for multiple session per host.
[SCSI] qla4xxx: Export CHAP index as sysfs attribute
[SCSI] scsi_transport: Export CHAP index as sysfs attribute
[SCSI] qla4xxx: Add support to display CHAP list and delete CHAP entry
[SCSI] iscsi_transport: Add support to display CHAP list and delete CHAP entry
[SCSI] pm8001: fix endian issue with code optimization.
[SCSI] pm8001: Fix possible racing condition.
[SCSI] pm8001: Fix bogus interrupt state flag issue.
[SCSI] ipr: update PCI ID definitions for new adapters
[SCSI] qla2xxx: handle default case in qla2x00_request_firmware()
[SCSI] isci: improvements in driver unloading routine
[SCSI] isci: improve phy event warnings
[SCSI] isci: debug, provide state-enum-to-string conversions
[SCSI] scsi_transport_sas: 'enable' phys on reset
[SCSI] libsas: don't recover end devices attached to disabled phys
[SCSI] libsas: fixup target_port_protocols for expanders that don't report sata
[SCSI] libsas: set attached device type and target protocols for local phys
...
1. Fix endian issue.
2. Fix the following warning :
" drivers/scsi/pm8001/pm8001_hwi.c:2932:32: warning: comparison
between ‘enum sas_device_type’ and ‘enum sas_dev_type’".
3. Few code optimization.
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
There is a possble racing scenario.
'process_oq' is called by two routines, as shown below.
pm8001_8001_dispatch = {
.......
.isr = pm8001_chip_isr --> process_oq,// A
.isr_process_oq = process_oq, // B
.....
}
process_oq() --> process_one_iomb() --> mpi_sata_completion()
In 'mpi_sata_completion', "pm8001_ha->lock" is first released.
It means lock is taken before, which is true for
the context A, as 'pm8001_ha->lock' is taken in 'pm8001_chip_isr()'
But for context B there is no lock taken before and pm8001_ha->lock
is unlocked in 'mpi_sata_completion()'. This may unlock the lock
taken in context A. Possible racing ??
If 'pm8001_ha->lock' is taken in 'process_oq()' instead of
'pm8001_chip_isr' then the above issue can be avoided.
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Static checker is giving following warning:
" error: calling 'spin_unlock_irqrestore()' with bogus flags"
The code flow is as shown below:
process_oq() --> process_one_iomb --> mpi_sata_completion
In 'mpi_sata_completion'
the first call for 'spin_unlock_irqrestore()' is with flags=0,
which is as good as 'spin_unlock_irq()' ( unconditional interrupt
enabling).
So for better performance 'spin_unlock_irqrestore()' can be replaced
with 'spin_unlock_irq()' and 'spin_lock_irqsave()' can be replaced by
'spin_lock_irq()'.
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
libsas ata error handling is already async but this does not help the
scan case. Move initial link recovery out from under host->scan_mutex,
and delay synchronization with eh until after all port probe/recovery
work has been queued.
Device ordering is maintained with scan order by still calling
sas_rphy_add() in order of domain discovery.
Since we now scan the domain list when invoking libata-eh we need to be
careful to check for fully initialized ata ports.
Acked-by: Jack Wang <jack_wang@usish.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In the direct-attached case this routine returns the phy on which this
device was first discovered. Which is broken if we want to support
wide-targets, as this phy reference can become stale even though the
port is still active.
In the expander-attached case this routine tries to lookup the phy by
scanning the attached sas addresses of the parent expander, and BUG_ONs
if it can't find it. However since eh and the libsas workqueue run
independently we can still be attempting device recovery via eh after
libsas has recorded the device as detached. This is even easier to hit
now that eh is blocked while device domain rediscovery takes place, and
that libata is fed more timed out commands increasing the chances that
it will try to recover the ata device.
Arrange for dev->phy to always point to a last known good phy, it may be
stale after the port is torn down, but it will catch up for wide port
reconfigurations, and never be NULL.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Each libsas driver (mvsas, pm8001, and isci) has invented a different
method for managing the ap->lock. The lock is held by the ata
->queuecommand() path. mvsas drops it prior to acquiring any internal
locks which allows it to hold its internal lock across calls to
task->task_done(). This capability is important as it is the only way
the driver can flush task->task_done() instances to guarantee that it no
longer has any in-flight references to a domain_device at
->lldd_dev_gone() time.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When an lldd invokes ->notify_port_event() it can trigger a chain of libsas
events to:
1/ form the port and find the direct attached device
2/ if the attached device is an expander perform domain discovery
A call to flush_workqueue() will only flush the initial port formation work.
Currently libsas users need to call scsi_flush_work() up to the max depth of
chain (which will grow from 2 to 3 when ata discovery is moved to its own
discovery event). Instead of open coding multiple calls switch to use
drain_workqueue() to flush sas work.
drain_workqueue() does not handle new work submitted during the drain so
libsas needs a bit of infrastructure to hold off unchained work submissions
while a drain is in flight. A lldd ->notify() event is considered 'unchained'
while a sas_discover_event() is 'chained'. As Tejun notes:
"For now, I think it would be best to add private wrapper in libsas to
support deferring unchained work items while draining."
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Per commit 3e4ec344 "libata: kill ATA_FLAG_DISABLED" needing to set
ATA_DEV_NONE is a holdover from before libsas converted to the
"new-style" ata-eh.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
IO_XFER_ERROR_BREAK and IO_XFER_OPEN_RETRY_TIMEOUT are deficient of the
required actions as outlined in the programming manual for the pm8001. Due to
the overlapping code requirements of these recovery responses, we found it
necessary to bundle them together into one patch.
When a break is received during the command phase (ssp_completion), this is a
result of a timeout or interruption on the bus. Logic suggests that we should
retry the command.
When a break is received during the data-phase (ssp_event), the task must be
aborted on the target or it will retain a data-phase lock turning the target
reticent to all future media commands yet will successfully respond to TUR,
INQUIRY and ABORT leading eventually to target failure through several
abort-cycle loops.
The open retry interval is exceedingly short resulting in occasional target
drop-off during expander resets or when targets push-back during bad-block
remapping. Increased effective timeout from 130ms to 1.5 seconds for each try
so as to trigger after the administrative inquiry/tur timeout in the scsi
subsystem to keep error-recovery harmonics to a minimum.
When an open retry timeout event is received, the action required by the
targets is to issue an abort for the outstanding command then logic suggests
we retry the command as this state is usually an indication of a credit block
or busy condition on the target.
We hijacked the pm8001_handle_event work queue handler so that it will handle
task as an argument instead of device for the workers in support of the
deferred handling outlined above.
Moderate to Heavy bad-path testing on a 2.6.32 vintage kernel, compile-testing
on scsi-misc-2.6 kernel ...
Signed-off-by: Mark Salyzyn <mark_salyzyn@xyratex.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Jack noticed I dropped a patch fragment associated with a flags automatic
variable in mpi_set_phys_g3_with_ssc (ooops) and that the pre-emptive locking
that piggy-backed this patch was not in-fact necessary because of underlying
atomic accesses to the hardware. Here is the updated patch fixing these two
issues.
The pm8001 driver is missing the FUNC_GET_EVENTS handler in the phy control
function. Since the pm8001_bar4_shift function was not designed to be called
at runtime, added locking surrounding the adjustment for all accesses.
Signed-off-by: Mark Salyzyn <mark_salyzyn@xyratex.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
pm8001_phy_control PHY_FUNC_HARD_RESET locks up on second try via
smp_phy_control because response HW_EVENT_PHY_START_STATUS fails to complete
previous command. The PM8001F_RUN_TIME flag is not treated as a bit, but a
state in all readers, yet once we are operational or in the run time state,
the flags use a bit-set operation.
Signed-off-by: Mark Salyzyn <mark_salyzyn@xyratex.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Correct typo "unresgister" to "unregister" and "deviece" to
"device" in drivers/scsi/pm8001/pm8001_hwi.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Allow the sas-transport-class to update events for local phys via a new
PHY_FUNC_GET_EVENTS command to ->lldd_control_phy(). Fixup drivers that
are not prepared for new enum phy_func values, and unify
->lldd_control_phy() error codes.
These are the SAS defined phy events that are reported in a
smp-report-phy-error-log command:
* /sys/class/sas_phy/<phyX>/invalid_dword_count
* /sys/class/sas_phy/<phyX>/running_disparity_error_count
* /sys/class/sas_phy/<phyX>/loss_of_dword_sync_count
* /sys/class/sas_phy/<phyX>/phy_reset_problem_count
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Code Inspection: found two missing break directives. First one will
result in not retrying an a task that report
IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY, the second will result in cosmetic
debug printk conflicting statement stutter. Because checkpatch.pl came
up with a warning regarding unnecessary space before a newline on one of
the fragments associated with the diff context, I took the liberty of
fixing all the cases of this issue in the pair of files touched by this
defect. These cosmetic changes hide the break changes :-(
To help focus, break changes are in pm8001_hwi.c fragment line 1649 for
the IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY case statement and pm8001_sas.c
line 1000 deals with the conflicting debug print stutter.
Signed-off-by: Mark Salyzyn <mark_salyzyn@us.xyratex.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
On the pm8001, when a device is in the process of going away (device
power off or hot plug), depending on the timing, the driver would return
SAS_PHY_DOWN as the return value to the queuecommand DEV_IS_GONE logic.
The net result is an near infinite retry (especially if SAS debugging is
enabled), the logs will fill with:
kernel: mpi_ssp_completion 2119:e21:SSP IO status 0x13 tag 0xcc1c0000
dlen=90 param=0xe
kernel: wwn=5000c50034069e86 cdb=12 00 00 00 5a 00 00 00 00 00 00 00 00
00 00 00
kernel: sas: lldd_execute_task returned: 138
kernel: sas: lldd_execute_task returned: 138
kernel: sas: lldd_execute_task returned: 138
kernel: sas: lldd_execute_task returned: 138
kernel: sas: lldd_execute_task returned: 138
kernel: sas: lldd_execute_task returned: 138
kernel: sas: lldd_execute_task returned: 138
. . .
This patch changes to leverage the port_attached logic to complete the
command with a status of PHY_DOWN so that the disposition can be handled
immediately and correctly.
Signed-off-by: Mark Salyzyn <mark_salyzyn@us.xyratex.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
libsas handles:
1/ limiting ata scanning to lun0
2/ changes to /sys/block/<sdX>/device/queue_depth for ata devices
libata handles turning off ncq globally via kernel command line
(libata.force=noncq) or sysfs (echo 1 >
/sys/block/<sdX>/device/queue_depth). A lldd specific compile option is
not necessary.
Cc: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Now that isci has added a 3rd open coded user of this functionality just
share the libsas version.
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pm8001 manages its own list of pending works and cancel them on device
free. It is unnecessarily complex and has a race condition - the
works are canceled but not synced, so the work could still be running
during and after the data structures are freed.
This patch simplifies workqueue usage.
* A driver specific workqueue pm8001_wq is created to serve these
work items.
* To avoid confusion, the "queue" suffixes are dropped from work items
and functions.
* Delayed queueing was never used. pm8001_work now uses work_struct
instead.
* The driver no longer keeps track of pending works. All pm8001_works
are queued to pm8001_wq and the workqueue is flushed as necessary.
flush_scheduled_work() usage is removed during conversion.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
The big kernel lock has been removed from all these files at some point,
leaving only the #include.
Remove this too as a cleanup.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Return -ENOMEM if the allocations fail.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Error handling code following a kmalloc should free the allocated data.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
expression E;
identifier f,f1;
position p1,p2;
@@
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
<... when != x
when != if (...) { <+...x...+> }
when != (x) == NULL
when != (x) != NULL
when != (x) == 0
when != (x) != 0
(
x->f1 = E
|
(x->f1 == NULL || ...)
|
f(...,x->f1,...)
)
...>
(
return <+...x...+>;
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: jack wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
We have two separate definitions for identical constants with nearly the
same name. One comes from the generic headers in scsi.h; the other is
an enum in libsas.h ... it's causing confusion about which one is
correct (fortunately they both are).
Fix this by eliminating the libsas.h duplicate
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In the original code we dereferenced "pm8001_dev" before checking if it
was null. This patch moves the dereference inside the condition.
This was found by a static checker (smatch). I looked, but I couldn't
tell if "pm8001_dev" dev was ever actually null. The approach in this
patch seemed like the safest response.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The region set by the call to memset is immediately overwritten by the
subsequent call to memcpy.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e1,e2,e3,e4;
@@
- memset(e1,e2,e3);
memcpy(e1,e4,e3);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
In particular, several occurances of funny versions of 'success',
'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address',
'beginning', 'desirable', 'separate' and 'necessary' are fixed.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use kzalloc rather than kcalloc(1,...)
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
@@
- kcalloc(1,
+ kzalloc(
...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by:Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add more data to printk's, add some spaces around arithmetic ops and
improve comments.
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Enhance error handle for IO patch, when the port is down, fast return phy
down for task.
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch fix for sata IO circular lock dependency. When we call task_done
for SATA IO, we have got pm8001_ha->lock ,and in sas_ata_task_done, it will
get (dev->sata_dev.ap->lock. then cause circular lock dependency .So we
should drop pm8001_ha->lock when we call task_done for SATA task.
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Lindar Liu <lindar_liu@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Allocate right size for bitmap tag,fix error goto and cleanup print
message and undocable commemts. patch attached.
Signed-off-by: Lindar Liu <lindar_liu@usish.com>
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
We set interupt cascading count of outbound queue to get better
performance, correct some unnecessary return values and some noisy
print messages. patch attached.
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Lindar Liu <lindar_liu@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Lindar Liu <lindar_liu@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This driver supports PMC-Sierra PCIe SAS/SATA 8x6G SPC 8001 chip based
host adapters.
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Lindar Liu <lindar_liu@usish.com>
Signed-off-by: Tom Peng <tom_peng@usish.com>
Signed-off-by: Kevin Ao <aoqingyun@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Sakthivel K