My OCD just couldn't let this slide. Spotted while reviewing Ville's
patch to only flip planes when we have FBC.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Looks like 830M doesn't quite like it when you try to move a plane from
one pipe to another. It seems that the plane's old pipe has to be active
even if the plane is already disabled, otherwise the relevant register
just won't accept new values.
The following commit:
commit 1f1c2e2468
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Thu Nov 28 17:30:01 2013 +0200
drm/i915: Swap primary planes on gen2 for FBC
caused a regression on 830M. It will attempt to swap the planes when the
driver is loaded, but at that time only pipe A might be active, so plane
A gets disabled, but plane B won't get enabled since pipe B is not
active when we try to move the plane over to pipe A.
There's no reason to swap planes on 830M since it doesn't support
FBC. Change the logic a bit to limit the plane swapping to platforms
which actually support FBC. This should avoid getting a black screen on
830M.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When the pipe A force quirk is applied the code will attempt to grab
a crtc mutex during intel_modeset_setup_hw_state(). If we're already
holding all crtc mutexes this will obviously deadlock every time.
So instead of using drm_modeset_lock_all() just grab the
mode_config.mutex. This is enough to avoid the unlocked mutex warnings
from certain lower level functions.
The regression was introduced in:
commit 0274766428
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Dec 2 11:08:06 2013 +0200
drm/i915: Take modeset locks around intel_modeset_setup_hw_state()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
[danvet: Add cc: stable since the offending commit has that, too.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add support for adreno 330. Not too much different, just a few
differences in initial configuration plus setting OCMEM base.
Userspace support is already in upstream mesa.
Note that the existing DT code is simply using the bindings from
downstream android kernel, to simplify porting of this driver to
existing devices. These do not constitute any committed/stable
DT ABI. The addition of proper DT bindings will be a subsequent
patch, at which point (as best as possible) I will try to support
either upstream bindings or what is found in downstream android
kernel, so that existing device DT files can be used.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add support for the new MDP5 display controller block. The mapping
between parts of the display controller and KMS is:
plane -> PIPE{RGBn,VIGn} \
crtc -> LM (layer mixer) |-> MDP "device"
encoder -> INTF /
connector -> HDMI/DSI/eDP/etc --> other device(s)
Unlike MDP4, it appears we can get by with a single encoder, rather
than needing a different implementation for DTV, DSI, etc. (Ie. the
register interface is same, just different bases.)
Also unlike MDP4, all the IRQs for other blocks (HDMI, DSI, etc) are
routed through MDP.
And finally, MDP5 has this "Shared Memory Pool" (called "SMP"), from
which blocks need to be allocated to the active pipes based on fetch
stride.
Signed-off-by: Rob Clark <robdclark@gmail.com>
The HDMI block is basically the same between older SoC's with mdp4
display controller, and newer ones with mdp5.
So mostly this consists of better abstracting out the different sets of
regulators, clks, etc. In particular, for regulators and clks we can
split it up by what is needed for hot plug detect to work, and what is
needed to light up the display.
Also, 8x74 has a new phy.. a very simple one, but split out into a
different mmio space. And with mdp5, the irq is shared with mdp, so we
don't directly register our own irq handler.
Signed-off-by: Rob Clark <robdclark@gmail.com>
This can be shared between mdp4 and mdp5. Both use the same set of
parameters to describe the format to the hw.
Signed-off-by: Rob Clark <robdclark@gmail.com>
There are some little bits and pieces that mdp4 and mdp5 can share, so
move things around so that we can have both in a common parent
directory.
Signed-off-by: Rob Clark <robdclark@gmail.com>
This adds the necessary configuration for the APQ8060A SoC (dual-core
krait + a320 gpu) as found on the bstem board.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add a VRAM carveout that is used for systems which do not have an IOMMU.
The VRAM carveout uses CMA. The arch code must setup a CMA pool for the
device (preferrably in highmem.. a 256m-512m VRAM pool in lowmem is not
cool). The user can configure the VRAM pool size using msm.vram module
param.
Technically, the abstraction of IOMMU behind msm_mmu is not strictly
needed, but it simplifies the GEM code a bit, and will be useful later
when I add support for a2xx devices with GPUMMU, so I decided to keep
this part.
It appears to be possible to configure the GPU to restrict access to
addresses within the VRAM pool, but this is not done yet. So for now
the GPU will refuse to load if there is no sort of mmu. Once address
based limits are supported and tested to confirm that we aren't giving
the GPU access to arbitrary memory, this restriction can be lifted
Signed-off-by: Rob Clark <robdclark@gmail.com>
This got a bit broken with original patches when re-arranging things to
move dependencies on mach-msm inside #ifndef OF.
Signed-off-by: Rob Clark <robdclark@gmail.com>
pci config reset is a low level reset that resets
the entire chip from the bus interface. It can
be more reliable if soft reset fails.
v2: fix rebase
v3: hide behind module parameter
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
pci config reset is a low level reset that resets
the entire chip from the bus interface. It can
be more reliable if soft reset fails.
v2: hide behind module parameter
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
pci config reset is a low level reset that resets
the entire chip from the bus interface. It can
be more reliable if soft reset fails.
v2: put behind module parameter
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
pci config reset is a low level reset that resets
the entire chip from the bus interface. It can
be more reliable if soft reset fails.
There's not much information still available on
r6xx, so r6xx is based on guess-work.
v2: put behind module parameter
v3: add IGP check
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is used to hard reset the asic. If a soft
reset is not able to reset things, a hard reset
can be used.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enabling this parameter enables pci config reset,
aka hard reset, which is a bus level chip reset.
In some cases this works more reliably than a soft
reset. Disabled by default.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
LPT does have PCH refclk, but it's different form the IBX/CPT/PPT one
and doesn't use the same structs. It is wrong to have a message saying
that "LPT does not has PCH refclk" (sic). While at it, signal that we
only want this function on IBX/CPT/PPT by renaming it and adding a
WARN.
On HSW we also print "0 shared PLLs initialized", but we *do* have
shared PLLs on HSW (LCPLL, WRPLL, SPLL) and we *do* initialize them.
We just don't use "struct intel_shared_dpll". So remove the debug
message.
In the future we may want to rename all that "intel shared pll" code
to "ibx shared pll", but I'll leave this to another patch.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This fixes a bug which was causing rejections of valid GPU commands
from userspace.
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's never allocated on systems without an ATOMBIOS or COMBIOS ROM.
Should fix an oops I encountered while resetting the GPU after a lockup
on my PowerBook with an RV350.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Properly zero the refcounts and crtc->ddi_pll_set so the previous HW
state doesn't affect the result of reading the current HW state.
This fixes WARNs about WRPLL refcount if we have an HDMI monitor on
HSW and then suspend/resume.
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=64379
Tested-by: Qingshuai Tian <qingshuai.tian@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to Art, we don't have a way to read back the state reliably at
runtime, through the control reg or the mailbox, at least not without risking
disabling it again. So drop the readout and checking on BDW.
v2: drop TODO comment (Paulo)
move POSTING_READ of control reg under HSW branch in disable (Paulo)
always report IPS as enabled on BDW (Paulo)
References: https://bugs.freedesktop.org/show_bug.cgi?id=71906
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mark functions as static because they are not used outside the file
drm/vmwgfx/vmwgfx_fence.c.
This eliminates the following warnings in drm/vmwgfx/vmwgfx_fence.c:
drivers/gpu/drm/vmwgfx/vmwgfx_fence.c:274:6: warning: no previous prototype for ‘vmw_fences_perform_actions’ [-Wmissing-prototypes]
drivers/gpu/drm/vmwgfx/vmwgfx_fence.c:900:6: warning: no previous prototype for ‘vmw_fence_obj_add_action’ [-Wmissing-prototypes]
drivers/gpu/drm/vmwgfx/vmwgfx_fence.c:996:5: warning: no previous prototype for ‘vmw_event_fence_action_create’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Mark functions as static because they are not used outside the file
drm/vmwgfx/vmwgfx_buffer.c.
This eliminates the following warnings in drm/vmwgfx/vmwgfx_buffer.c:
drivers/gpu/drm/vmwgfx/vmwgfx_buffer.c:520:16: warning: no previous prototype for ‘vmw_ttm_tt_create’ [-Wmissing-prototypes]
drivers/gpu/drm/vmwgfx/vmwgfx_buffer.c:549:5: warning: no previous prototype for ‘vmw_invalidate_caches’ [-Wmissing-prototypes]
drivers/gpu/drm/vmwgfx/vmwgfx_buffer.c:554:5: warning: no previous prototype for ‘vmw_init_mem_type’ [-Wmissing-prototypes]
drivers/gpu/drm/vmwgfx/vmwgfx_buffer.c:592:6: warning: no previous prototype for ‘vmw_evict_flags’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Mark functions as static because they are not used outside the file
drm/vmwgfx/vmwgfx_kms.c.
This eliminates the following warnings in drm/vmwgfx/vmwgfx_kms.c:
drivers/gpu/drm/vmwgfx/vmwgfx_kms.c:43:6: warning: no previous prototype for ‘vmw_clip_cliprects’ [-Wmissing-prototypes]
drivers/gpu/drm/vmwgfx/vmwgfx_kms.c:426:6: warning: no previous prototype for ‘vmw_framebuffer_surface_destroy’ [-Wmissing-prototypes]
drivers/gpu/drm/vmwgfx/vmwgfx_kms.c:592:5: warning: no previous prototype for ‘vmw_framebuffer_surface_dirty’ [-Wmissing-prototypes]
drivers/gpu/drm/vmwgfx/vmwgfx_kms.c:757:6: warning: no previous prototype for ‘vmw_framebuffer_dmabuf_destroy’ [-Wmissing-prototypes]
drivers/gpu/drm/vmwgfx/vmwgfx_kms.c:943:5: warning: no previous prototype for ‘vmw_framebuffer_dmabuf_dirty’ [-Wmissing-prototypes]
drivers/gpu/drm/vmwgfx/vmwgfx_kms.c:1666:5: warning: no previous prototype for ‘vmw_du_update_layout’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Remove unused function ttm_write_lock_downgrade() from
drm/ttm/ttm_lock.c.
This eliminates the following warning in drm/ttm/ttm_lock.c:
drivers/gpu/drm/ttm/ttm_lock.c:189:6: warning: no previous prototype for ‘ttm_write_lock_downgrade’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Mark functions as static because they are not used outside the file
drm/ttm/ttm_bo_util.c.
This eliminates the following warnings in drm/ttm/ttm_bo_util.c:
drivers/gpu/drm/ttm/ttm_bo_util.c:190:5: warning: no previous prototype for ‘ttm_mem_reg_ioremap’ [-Wmissing-prototypes]
drivers/gpu/drm/ttm/ttm_bo_util.c:222:6: warning: no previous prototype for ‘ttm_mem_reg_iounmap’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Mark function as static because it is not used outside file
drm/ttm/ttm_bo.c.
This eliminates the following warning in drm/ttm/ttm_bo.c:
drivers/gpu/drm/ttm/ttm_bo.c:960:5: warning: no previous prototype for ‘ttm_bo_move_buffer’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
This was introduced in:
commit 7c4a395ff8
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Wed Oct 9 19:17:56 2013 +0300
drm/i915: Don't re-compute pipe watermarks except for the affected pipe
and I missed fixing it in:
commit fec8cba306
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Wed Nov 27 11:10:26 2013 -0800
drm/i915: use crtc_htotal in watermark calculations to match fastboot v2
It's needed for ILK+ platforms to fastboot without crashing on a divide
by 0 after a DPMS on action.
Note: Ville mentioned in his review that this confusion seems to go
down to the original introduction of this code in
commit 801bcfffbb
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Fri May 31 10:08:35 2013 -0300
drm/i915: properly set HSW WM_PIPE registers
So it seems to have been missed both in the fastboot patch and in the
3d mode suppport (where only crtc_htotal reflects the real pipe
width).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add note based on Ville's review.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When a client looks up a ttm object, don't look it up through the device hash
table, but rather from the file hash table. That makes sure that the client
has indeed put a reference on the object, or in gem terms, has opened
the object; either using prime or using the global "name".
To avoid a performance loss, make sure the file hash table entries can be
looked up from under an RCU lock, and as a consequence, replace the rwlock
with a spinlock, since we never need to take it in read mode only anymore.
Finally add a ttm object lookup function for the device hash table, that is
intended to be used when we put a ref object on a base object or, in gem terms,
when we open the object.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Needed for some vm operations; most notably unmap_mapping_range() with
even_cows = 0.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
This is illegal for at least two reasons:
1) While it may work on some platforms / iommus, obtaining page pointers from
mapped sg-lists is illegal, since the DMA API allows page pointer information
to be destroyed in the sg mapping process.
2) TTM has no way of determining the linear kernel map caching state of the
underlying pages. PTEs with conflicting caching state pointing to the same
pfn is not allowed.
TTM operations touching pages of imported sg-tables should be redirected through
the proper dma-buf operations.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
VM_PFNMAP is faster than VM_MIXEDMAP due to reduced page administration so
use it for shared maps where we don't have any Copy-On-Write pages. For
private maps, we continue to use VM_MIXEDMAP.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
misc fixes for nouveau, one more msi rearm, regression fix for old bioses
crash and leak fixes.
* 'drm-nouveau-next' of git://anongit.freedesktop.org/nouveau/linux-2.6:
drm/nouveau/nouveau: fix memory leak in nouveau_crtc_page_flip()
drm/nouveau/bios: fix offset calculation for BMPv1 bioses
drm/nouveau: return offset of allocated notifier
drm/nouveau/bios: make jump conditional
drm/nvce/mc: fix msi rearm on GF114
drm/nvc0/gr: fix mthd data submission
drm/nouveau: populate master subdev pointer only when fully constructed
When fastbooting, we read out the pipe timings early on, and then in a
panel fitted config, disable the fitter later. But we weren't updating
the pipe src h/w, which meant the mouse cursor was clipped to the
pfitted size rather than the native size set later. Fix that up so the
cursor is visible in the new mode.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise we won't check the state until the next DPMS transition, which
may never happen.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix a memory leak in the nouveau_crtc_page_flip() error handling path.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The only BIOS on record that needs the 14 offset has a bios major
version 2 but BMP version 1.01. Another bunch of BIOSes that need the 18
offset have BMP version 2.01 or 5.01 or higher. So instead of looking at the
bios major version, look at the BMP version. BIOSes with BMP version 0
do not contain a detectable script, so always return 0 for them.
See https://bugs.freedesktop.org/show_bug.cgi?id=68835
Reported-by: Mauro Molinari <mauromol@tiscali.it>
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Avoid duplicating the same piece of code several times by separating
the watemark vfunc setup from the init_clock_gating vfunc setup on PCH
platforms.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We forgot to intialize the watermark vfuncs for BDW, and hence the
watermarks were never updated.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Looks like I forgot to update the ILK/SNB/IVB watermark patches to deal
with BDW. Add the relevant BDW checks to make sure we take the HSW
codepaths on BDW as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move prototype declarations of functions radeon_get_encoder_enum() and
radeon_link_encoder_connector() to header file drm/radeon/radeon_mode.h
because they are used by more than one file.
This eliminates the following warnings in drm/radeon/radeon_encoders.c:
drivers/gpu/drm/radeon/radeon_encoders.c:86:1: warning: no previous prototype for ‘radeon_get_encoder_enum’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_encoders.c:162:1: warning: no previous prototype for ‘radeon_link_encoder_connector’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move prototype declaration of functions radeon_add_atom_connector() and
radeon_add_legacy_connector() to header file drm/radeon/radeon_mode.h
because they are used by more than one file.
This eliminates the following warning in drm/radeon/radeon_connectors.c:
drivers/gpu/drm/radeon/radeon_connectors.c:1588:1: warning: no previous prototype for ‘radeon_add_atom_connector’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_connectors.c:2020:1: warning: no previous prototype for ‘radeon_add_legacy_connector’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
fixes warnings with -Wmissing-prototypes
Based on initial patches from Rashika Kheria.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Rashika Kheria <rashika.kheria@gmail.com>
Noticed by Rashika Kheria and cherry-picked from
her larger patch set.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Rashika Kheria <rashika.kheria@gmail.com>
Noticed by Rashika Kheria and cherry-picked from
her larger patch set.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Rashika Kheria <rashika.kheria@gmail.com>
Noticed by Rashika Kheria and cherry-picked from
her larger patch set.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Rashika Kheria <rashika.kheria@gmail.com>
Include header file drm/radeon/ci_dpm.h in drm/radeon/ci_smc.c because
it uses function declared in the header file.
This eliminates the following warnings in drm/radeon/ci_smc.c:
drivers/gpu/drm/radeon/ci_smc.c:46:5: warning: no previous prototype for ‘ci_copy_bytes_to_smc’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/ci_smc.c:113:6: warning: no previous prototype for ‘ci_start_smc’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/ci_smc.c:121:6: warning: no previous prototype for ‘ci_reset_smc’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/ci_smc.c:129:5: warning: no previous prototype for ‘ci_program_jump_on_start’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/ci_smc.c:136:6: warning: no previous prototype for ‘ci_stop_smc_clock’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/ci_smc.c:145:6: warning: no previous prototype for ‘ci_start_smc_clock’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/ci_smc.c:154:6: warning: no previous prototype for ‘ci_is_smc_running’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/ci_smc.c:165:14: warning: no previous prototype for ‘ci_send_msg_to_smc’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/ci_smc.c:186:14: warning: no previous prototype for ‘ci_wait_for_smc_inactive’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/ci_smc.c:204:5: warning: no previous prototype for ‘ci_load_smc_ucode’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/ci_smc.c:251:5: warning: no previous prototype for ‘ci_read_smc_sram_dword’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/ci_smc.c:266:5: warning: no previous prototype for ‘ci_write_smc_sram_dword’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move prototype declaration of function radeon_atom_copy_swap() to header
file drm/radeon/radeon_mode.h because it is used by more than one file.
This eliminates the following warnings in drm/radeon/atombios_dp.c:
drivers/gpu/drm/radeon/atombios_dp.c:53:6: warning: no previous prototype for ‘radeon_atom_copy_swap’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Include header file gpu/drm/radeon/sislands_smc.h in drm/radeon/si_smc.c
because it uses function declared in the header file.
Remove prototype declaration of function si_set_smc_sram_address() from
drm/radeon/sislands_smc.h because the function is used only in one file
where it is declared static already.
This eliminates the following warnings in drm/radeon/si_smc.c:
drivers/gpu/drm/radeon/si_smc.c:46:5: warning: no previous prototype for ‘si_copy_bytes_to_smc’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/si_smc.c:112:6: warning: no previous prototype for ‘si_start_smc’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/si_smc.c:121:6: warning: no previous prototype for ‘si_reset_smc’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/si_smc.c:135:5: warning: no previous prototype for ‘si_program_jump_on_start’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/si_smc.c:142:6: warning: no previous prototype for ‘si_stop_smc_clock’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/si_smc.c:151:6: warning: no previous prototype for ‘si_start_smc_clock’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/si_smc.c:160:6: warning: no previous prototype for ‘si_is_smc_running’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/si_smc.c:171:14: warning: no previous prototype for ‘si_send_msg_to_smc’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/si_smc.c:192:14: warning: no previous prototype for ‘si_wait_for_smc_inactive’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/si_smc.c:210:5: warning: no previous prototype for ‘si_load_smc_ucode’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/si_smc.c:269:5: warning: no previous prototype for ‘si_read_smc_sram_dword’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/si_smc.c:284:5: warning: no previous prototype for ‘si_write_smc_sram_dword’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add static keyword to the definition of KMS_INVALID_IOCTL(name) in
radeon_kms.c because the functions passed to it as arguments are not
used anywhere else.
This eliminates the following warnings in drm/radeon/radeon_kms.c:
drivers/gpu/drm/radeon/radeon_kms.c:719:1: warning: no previous prototype for ‘radeon_cp_init_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:720:1: warning: no previous prototype for ‘radeon_cp_start_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:721:1: warning: no previous prototype for ‘radeon_cp_stop_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:722:1: warning: no previous prototype for ‘radeon_cp_reset_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:723:1: warning: no previous prototype for ‘radeon_cp_idle_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:724:1: warning: no previous prototype for ‘radeon_cp_resume_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:725:1: warning: no previous prototype for ‘radeon_engine_reset_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:726:1: warning: no previous prototype for ‘radeon_fullscreen_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:727:1: warning: no previous prototype for ‘radeon_cp_swap_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:728:1: warning: no previous rototype for ‘radeon_cp_clear_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:729:1: warning: no previous prototype for ‘radeon_cp_vertex_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:730:1: warning: no previous rototype for ‘radeon_cp_indices_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:731:1: warning: no previous prototype for ‘radeon_cp_texture_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:732:1: warning: no previous prototype for ‘radeon_cp_stipple_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:733:1: warning: no previous prototype for ‘radeon_cp_indirect_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:734:1: warning: no previous prototype for ‘radeon_cp_vertex2_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:735:1: warning: no previous prototype for ‘radeon_cp_cmdbuf_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:736:1: warning: no previous prototype for ‘radeon_cp_getparam_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:737:1: warning: no previous prototype for ‘radeon_cp_flip_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:738:1: warning: no previous prototype for ‘radeon_mem_alloc_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:739:1: warning: no previous prototype for ‘radeon_mem_free_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:740:1: warning: no previous rototype for ‘radeon_mem_init_heap_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:741:1: warning: no previous rototype for ‘radeon_irq_emit_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:742:1: warning: no previous prototype for ‘radeon_irq_wait_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:743:1: warning: no previous rototype for ‘radeon_cp_setparam_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:744:1: warning: no previous prototype for ‘radeon_surface_alloc_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:745:1: warning: no previous prototype for ‘radeon_surface_free_kms’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mark function r600_audio_set_dto() as static in drm/radeon/r600_hdmi.c
because it is not used outside this file.
This eliminates the following warning in drm/radeon/r600_hdmi.c:
drivers/gpu/drm/radeon/r600_hdmi.c:253:6: warning: no previous prototype for ‘r600_audio_set_dto’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mark function radeon_gem_set_domain() as static in
drm/radeon/radeon_gem.c because it is not used outside this file.
This eliminates the following warning in drm/radeon/radeon_gem.c:
drivers/gpu/drm/radeon/radeon_gem.c:89:5: warning: no previous prototype for ‘radeon_gem_set_domain’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mark function radeon_info_ioctl() as static in drm/radeon/radeon_kms.c
because it is not used outside this file.
This eliminates the following warning in drm/radeon/radeon_kms.c:
drivers/gpu/drm/radeon/radeon_kms.c:194:5: warning: no previous prototype for ‘radeon_info_ioctl’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mark functions radeon_doorbell_init() and radeon_doorbell_fini() as
static in drm/radeon/radeon_device.c because they are not used outside
this file.
This eliminates the following warning in drm/radeon/radeon_device.c:
drivers/gpu/drm/radeon/radeon_device.c:252:5: warning: no previous prototype for ‘radeon_doorbell_init’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_device.c:281:6: warning: no previous prototype for ‘radeon_doorbell_fini’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mark function radeon_bo_clear_va() as static in
drm/radeon/radeon_object.c because it is not used outside this file.
This eliminates the following warning in drm/radeon/radeon_object.c:
drivers/gpu/drm/radeon/radeon_object.c:49:6: warning: no previous prototype for ‘radeon_bo_clear_va’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The hw i2c engines are disabled by default as the
current implementation is still experimental. Print
a warning when users enable it so that it's obvious
when the option is enabled.
v2: check for non-0 rather than 1
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
We're iterating over the CPU transcoders, so check for the correct
power domain.
This fixes many "unclaimed register" error messages.
This can be reproduced by the IGT test mentioned below, but we still
get a FAIL when we run it.
Testcase: igt/kms_lip/flip-vs-panning-vs-hang
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In very rare cases (such as a memory failure stress test) it is possible
to fill the entire ring without emitting a request. Under this
circumstance, the outstanding request is flushed and waited upon. After
space on the ring is cleared, we return to emitting the new command -
except that we just cleared the seqno allocated for this operation and
trigger the sanity check that a request is only ever emitted with a
valid seqno. The fix is to rearrange the code to make sure the
allocation of the seqno for this operation is after any required flushes
of outstanding operations.
The bug exists since the preallocation was introduced in
commit 9d7730914f
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Nov 27 16:22:52 2012 +0000
drm/i915: Preallocate next seqno before touching the ring
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Multiple definitions show up multiple times in modinfo output.
There's already an identical one in i915_drv.c along with other MODULE_*
definitions, so drop the lone one in intel_fbdev.c.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DRM_HZ and DRM_WAKEUP macros are removed, but they still remained.
So this patch fixes build errors by replacing the macros.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch resolves potential deadlock issue that can be incurred
by changing file->f_op and filp->private_data to exynos specific
mapper ops and gem object temporarily.
To resolve this issue, this patch creates a new anon file dedicated
to exynos specific mmaper, and making it used instead of existing one.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The bug from gen6_ppgtt_insert_entries() was replicated into
gen8_ppgtt_insert_entries(). This applies the fix for the OOPS from the
previous patch to the gen8 routine.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The iommu and gfx on Ironlake do not like each other and require a
big hammer to prevent hard machine hangs. In
commit 5c0422878f
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Mon Oct 17 15:51:55 2011 -0700
drm/i915: ILK + VT-d workaround
we added the workaround, but never emitted any debug message that it was
active. Doing so should help identify known performance regressions.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This fixes a hang in VBIOS scripts of the form "condition; jump".
The jump used to always be executed, while now it will only be
executed if the condition is true.
See https://bugs.freedesktop.org/show_bug.cgi?id=72943
Reported-by: Darcy Brás da Silva <dardevelin@cidadecool.com>
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: stable@vger.kernel.org
If the initial data element is 0, it will never be written, even
though the value from the previous method may be there.
Signed-off-by: Kelly Doran <kel.p.doran@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
My Acer 8510TZ stops displaying anything when X starts with Linus' current
tree. I bisected it down to commit ee1452d745.
This patch reverts commit ee1452d745.
After the revert, everything works as before.
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Reported-by: Dylan Borg <borgdylan@hotmail.com> (for a Acer Extensa 5635Z)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
gem_gtt_cpu_tlb seems to indicate that it is needed.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=72869
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since get_pid_task() grabs a reference on the task_struct, we have to drop the
refcount after reading that task's comm name. Use pid_task() with RCU instead.
Also, avoid directly reading like pid_task()->comm because
pid_task() will return NULL if the task have already exit()ed.
This patch fixes both problems.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- VGA switcheroo was broken for some users as a result of the ACPI-based
PCI hotplug (ACPIPHP) changes in 3.12, because some previously ignored
hotplug events started to be handled. The fix causes them to be
ignored again.
- There are two more issues related to cpufreq's suspend/resume handling
changes from the 3.12 cycle addressed by Viresh Kumar's fixes.
- intel_pstate triggers a divide error in a timer function if the P-state
information it needs is missing during initialization. This leads to
kernel panics on nested KVM clients and is fixed by failing the
initialization cleanly in those cases.
- PCI initalization code changes during the 3.9 cycle uncovered BIOS
issues related to ACPI wakeup notifications (some BIOSes send them
for devices that aren't supposed to support ACPI wakeup). Work around
them by installing an ACPI wakeup notify handler for all PCI devices
with ACPI support.
- The Calxeda cpuilde driver's probe function is tagged as __init, which
is incorrect and causes a section mismatch to occur during build. Fix
from Andre Przywara removes the __init tag from there.
- During the 3.12 cycle ACPIPHP started to print warnings about missing
_ADR for devices that legitimately don't have it. Fix from Toshi Kani
makes it only print the warnings where they make sense.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABCAAGBQJSxrJgAAoJEILEb/54YlRxRPkP/ifzrrVhdzqXIEy44b93JeDx
oSmZW6yTO51GZlDx2bjt6CGJcIUDC4ExYV6S2tB44/DL19CYdIxi7oBaXtUvzGRs
oZ6B1wfvKOIxZ0RQguaGd1uerQU304CGwUXu/jpRZ/UuZZFKq5Uts6O3bilGzCfR
Y+MUH+qECwdBXaFHUISdWFsa3lxj0U0kglszh+DsxwS4gy/pLbCu5fKLgHLuNNQC
hhEEToQ6uF4o8hbkGJvgUPo3V3aUSXObgvJh4ntP09YE1AEJScLB4wKmqL0zN8Qj
pbBf1WC5OpGXv8zGM9ErrY64YaKA36uhJvOi6RtBGLbG+pYM6E6IM9zNf4Ku+T79
JNEulpq27aEx2JghNSgMFYQZEOGTH+q24iXZdZlOIvqWpMymATlqP/gAQQIpg3VC
OIIdocMFRsbgwFXf41uyUqs458fg5xREz5k6geWZeyriM45wFShR+JnMopQWc5OB
a3sbcWUShFBL1T0pqYR4SDLDvH4NdEP2NKO2jlqMXUewLXsVRRt/42etGoe0rI3C
cMWPQq7z0GNN+NboUviqwHdxUKqONWGt+pd/3u8FI/Y1IlXEeXQYGawhSu81uCpT
5gLaKDkwOrCSwOw68Msuod0Cce6TnoTowi6hP2aAEu8mDJwQY+toqA3+CPoO8nty
DdhZjP1afEgsVVyjErX4
=LXh0
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and PM fixes and new device IDs from Rafael Wysocki:
"These commits, except for one, are regression fixes and the remaining
one fixes a divide error leading to a kernel panic. The majority of
the regressions fixed here were introduced during the 3.12 cycle, one
of them is from this cycle and one is older.
Specifics:
- VGA switcheroo was broken for some users as a result of the
ACPI-based PCI hotplug (ACPIPHP) changes in 3.12, because some
previously ignored hotplug events started to be handled. The fix
causes them to be ignored again.
- There are two more issues related to cpufreq's suspend/resume
handling changes from the 3.12 cycle addressed by Viresh Kumar's
fixes.
- intel_pstate triggers a divide error in a timer function if the
P-state information it needs is missing during initialization.
This leads to kernel panics on nested KVM clients and is fixed by
failing the initialization cleanly in those cases.
- PCI initalization code changes during the 3.9 cycle uncovered BIOS
issues related to ACPI wakeup notifications (some BIOSes send them
for devices that aren't supposed to support ACPI wakeup). Work
around them by installing an ACPI wakeup notify handler for all PCI
devices with ACPI support.
- The Calxeda cpuilde driver's probe function is tagged as __init,
which is incorrect and causes a section mismatch to occur during
build. Fix from Andre Przywara removes the __init tag from there.
- During the 3.12 cycle ACPIPHP started to print warnings about
missing _ADR for devices that legitimately don't have it. Fix from
Toshi Kani makes it only print the warnings where they make sense"
* tag 'pm+acpi-3.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPIPHP / radeon / nouveau: Fix VGA switcheroo problem related to hotplug
intel_pstate: Fail initialization if P-state information is missing
ARM/cpuidle: remove __init tag from Calxeda cpuidle probe function
PCI / ACPI: Install wakeup notify handlers for all PCI devs with ACPI
cpufreq: preserve user_policy across suspend/resume
cpufreq: Clean up after a failing light-weight initialization
ACPI / PCI / hotplug: Avoid warning when _ADR not present
* acpi-pci-pm:
PCI / ACPI: Install wakeup notify handlers for all PCI devs with ACPI
* acpi-pci-hotplug:
ACPIPHP / radeon / nouveau: Fix VGA switcheroo problem related to hotplug
ACPI / PCI / hotplug: Avoid warning when _ADR not present
The changes in the ACPI-based PCI hotplug (ACPIPHP) subsystem made
during the 3.12 development cycle uncovered a problem with VGA
switcheroo that on some systems, when the device-specific method
(ATPX in the radeon case, _DSM in the nouveau case) is used to turn
off the discrete graphics, the BIOS generates ACPI hotplug events for
that device and those events cause ACPIPHP to attempt to remove the
device from the system (they are events for a device that was present
previously and is not present any more, so that's what should be done
according to the spec). Then, the system stops functioning correctly.
Since the hotplug events in question were simply silently ignored
previously, the least intrusive way to address that problem is to
make ACPIPHP ignore them again. For this purpose, introduce a new
ACPI device flag, no_hotplug, and modify ACPIPHP to ignore hotplug
events for PCI devices whose ACPI companions have that flag set.
Next, make the radeon and nouveau switcheroo detection code set the
no_hotplug flag for the discrete graphics' ACPI companion.
Fixes: bbd34fcdd1 (ACPI / hotplug / PCI: Register all devices under the given bridge)
References: https://bugzilla.kernel.org/show_bug.cgi?id=61891
References: https://bugzilla.kernel.org/show_bug.cgi?id=64891
Reported-and-tested-by: Mike Lothian <mike@fireburn.co.uk>
Reported-and-tested-by: <madcatx@atlas.cz>
Reported-and-tested-by: Joaquín Aramendía <samsagax@gmail.com>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
Fill in asic family specific versions rather than
using the generic version. This lets us handle asic
specific differences more easily. In this case, we
disable sw swapping of the rtpr writeback value on
r6xx+ since the hw does it for us. Fixes bogus
rptr readback on BE systems.
v2: remove missed cpu_to_le32(), add comments
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable coarse grained clockgating. This works properly now
that smc is initialized earlier than the rlc and cp.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable coarse grained clockgating on CIK dGPUs. This
works properly now that smc is initialized earlier than
the rlc and cp.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need more control over the ordering of dpm init with
respect to the rest of the asic. Specifically, the SMC
has to be initialized before the rlc and cg/pg. The pm
code currently initializes late in the driver, but we need
it to happen much earlier so move pm handling into the asic
specific callbacks.
This makes dpm more reliable and makes clockgating work
properly on CIK parts and should help on SI parts as well.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Right now it's called right after enable, but after
reworking the dpm init order, it will get called later
to accomodate loading the smc early, but enabling
thermal interrupts and block powergating later after
the ring tests are complete.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Make sure interrupts are enabled
before we enable thermal interrupts.
Also, don't powergate uvd, etc. until after
the ring tests.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Make sure interrupts are enabled
before we enable thermal interrupts.
Also, don't powergate uvd until after
the ring tests.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to wait to enable cg and pg until after
ring tests. Also make sure interrupts are enabled
before we enable thermal interrupts.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to wait to enable cg and pg until after
ring tests. Also make sure interrupts are enabled
before we enable thermal interrupts.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Certain features need to be enabled after ring tests
(e.g., powergating, etc.). Add a function pointer
to split out late enable features.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need to reorder the driver init sequence to better accomodate
dpm which needs to be loaded earlier in the init sequence. Move
fw init up so that it's available for dpm init.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
v2: add default_llseek
v3: set inode size in the open callback
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Not very fast, but makes it possible to access even the
normally inaccessible parts of VRAM from userspace.
v2: use MM_INDEX_HI for >2GB mem access, add default_llseek
v3: set inode size in the open callback
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Otherwise we not necessary export the right information.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We don't have the NUM_BANKS parameter, so we have to calculate it
from the other parameters. NUM_BANKS is not constant on CIK.
This fixes 2D tiling for the display engine on CIK.
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This will allow userspace to correctly program the PA_SC_RASTER_CONFIG
register, so it can be considered a fix.
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Only the render backends of the first shader engine were enabled. The others
were erroneously disabled. Enabling the other render backends improves
performance a lot.
Unigine Sanctuary on Bonaire:
Before: 15 fps
After: 90 fps
Judging from the fan noise, the GPU was also underclocked when the other
render backends were disabled, resulting in horrible performance. The fan is
a lot noisy under load now.
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Otherwise the kernel might reject our decoding requests.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DRM driver for (virtual) vga cards using the bochs dispi
interface, such as the qemu standard vga (qemu -vga std).
Don't bother supporting anything but 32bpp for now, even
though the virtual hardware is able to do that.
Known issue: mmap(/dev/fb0) doesn't work.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- fbc1 improvements from Ville (pre-gm45).
- vlv forcewake improvements from Deepak S.
- Some corner-cases fixes from Mika for the context hang stat code.
- pc8 improvements and prep work for runtime D3 from Paulo, almost ready for
primetime.
- gen2 dpll fixes from Ville.
- DSI improvements from Shobhit Kumar.
- A few smaller fixes and improvements all over.
[airlied: intel_ddi.c conflict fixed up]
* tag 'drm-intel-next-2013-12-13' of git://people.freedesktop.org/~danvet/drm-intel: (61 commits)
drm/i915/bdw: Implement ff workarounds
drm/i915/bdw: Force all Data Cache Data Port access to be Non-Coherent
drm/i915/bdw: Don't use forcewake needlessly
drm/i915: Clear out old GT FIFO errors in intel_uncore_early_sanitize()
drm/i915: dont call irq_put when irq test is on
drm/i915: Rework the FBC interval/stall stuff a bit
drm/i915: Enable FBC for all mobile gen2 and gen3 platforms
drm/i915: FBC_CONTROL2 is gen4 only
drm/i915: Gen2 FBC1 CFB pitch wants 32B units
drm/i915: split intel_ddi_pll_mode_set in 2 pieces
drm/i915: Fix timeout with missed interrupts in __wait_seqno
drm/i915: touch VGA MSR after we enable the power well
drm/i915: extract hsw_power_well_post_{enable, disable}
drm/i915: remove i915_disable_vga_mem declaration
drm/i915: Parametrize the dphy and other spec specific parameters
drm/i915: Remove redundant DSI PLL enabling
drm/i915: Reorganize the DSI enable/disable sequence
drm/i915: Try harder to get best m, n, p values with minimal error
drm/i915: Compute dsi_clk from pixel clock
drm/i915: Use FLISDSI interface for band gap reset
...
Conflicts:
drivers/gpu/drm/i915/intel_ddi.c
This series of changes brings DRM panel support as well as initial code
to register DSI hosts and peripherals and bind them to DSI drivers. The
panel and DSI code are both used by the simple panel driver.
The Tegra-specific changes build on top of this work to add support for
various panels found on Tegra boards. New drivers enable the DSI host
found on Tegra114 and a special hardware block that calibrates the pads
used for DSI and CSI. The host1x and the display controller drivers gain
basic Tegra124 support. To round of the new features, the DRM driver now
sports a very simple PRIME implementation.
In addition there are various improvements such as the host1x API being
exported so that client drivers (like the Tegra DRM driver) can be built
as modules. HDMI now does better power management and legacy FBDEV can
now be disabled via Kconfig (though it's still enabled by default). A
few sparse warnings have been squashed and various parts of the code
have become more robust.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=lQsh
-----END PGP SIGNATURE-----
Merge tag 'drm/for-3.14-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v3.14-rc1
This series of changes brings DRM panel support as well as initial code
to register DSI hosts and peripherals and bind them to DSI drivers. The
panel and DSI code are both used by the simple panel driver.
The Tegra-specific changes build on top of this work to add support for
various panels found on Tegra boards. New drivers enable the DSI host
found on Tegra114 and a special hardware block that calibrates the pads
used for DSI and CSI. The host1x and the display controller drivers gain
basic Tegra124 support. To round of the new features, the DRM driver now
sports a very simple PRIME implementation.
In addition there are various improvements such as the host1x API being
exported so that client drivers (like the Tegra DRM driver) can be built
as modules. HDMI now does better power management and legacy FBDEV can
now be disabled via Kconfig (though it's still enabled by default). A
few sparse warnings have been squashed and various parts of the code
have become more robust.
* tag 'drm/for-3.14-rc1' of git://anongit.freedesktop.org/tegra/linux: (121 commits)
drm/tegra: fix compile w/ CONFIG_DYNAMIC_DEBUG
drm/tegra: Add PRIME support
drm/tegra: Relocate some output-specific code
drm/tegra: Add Tegra124 DC support
drm/tegra: Fix small leak on error in tegra_fb_alloc()
drm/tegra: Make legacy fbdev support optional
drm/tegra: Sort reverse-dependencies alphabetically
drm/tegra: Fix return value check
drm/tegra: Add DSI support
drm/tegra: Disable outputs for power-saving
drm/tegra: Track HDMI enable state
drm/tegra: Fix HDMI audio frequency typo
drm/tegra: Do not export tegra_bo_ops
drm/tegra: Remove spurious blank line
drm/tegra: Increase compile test coverage
drm/tegra: Allow the driver to be built as a module
gpu: host1x: Add Tegra124 support
gpu: host1x: clk_round_rate() can return a zero upon error
gpu: host1x: Fix build warnings
gpu: host1x: Increase compile test coverage
...
rcar misc changes.
* 'drm/next/du' of git://linuxtv.org/pinchartl/fbdev:
drm/rcar-du: Add support for the r8a7791 DU
drm/rcar-du: Add LVDS_LANES quirk
drm/rcar-du: Split features and quirks
drm/rcar-du: Update plane pitch in .mode_set_base() operation
drm/rcar-du: Don't cast crtc to rcrtc twice in the same function
drm/rcar-du: fix return value check in rcar_du_lvdsenc_get_resources()
Besides the 2 fixes for tricky corner cases in gem from Chris I've
promised already two patche from Paulo to fix pc8 warnings (both ported
from -next, bug report from Dave Jones) and one patch from to fix vga
enable/disable on snb+. That one is a really old bug, but apparently it
can cause machine hangs if you try hard enough with vgacon/efifb handover.
* tag 'drm-intel-fixes-2013-12-18' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Use the correct GMCH_CTRL register for Sandybridge+
drm/i915: get a PC8 reference when enabling the power well
drm/i915: change CRTC assertion on LCPLL disable
drm/i915: Fix erroneous dereference of batch_obj inside reset_status
drm/i915: Prevent double unref following alloc failure during execbuffer
- fix for a long standing corruption bug on some Trinity/Richland parts.
- Stability fix for cayman dpm
- audio fixes for dce6+
* 'drm-fixes-3.13' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix asic gfx values for scrapper asics
drm/radeon: check for 0 count in speaker allocation and SAD code
drm/radeon/dpm: disable ss on Cayman
drm/radeon/dce6: set correct number of audio pins
Commit "drm/ttm: Don't move non-existing data" didn't take the
swapped-out corner case into account. This patch corrects that.
Fixes blank screen after attempted suspend / hibernate on vmwgfx.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix build error: qxl uses crc32 functions so it needs to select
CRC32.
Also use angle quotes around a kernel header file name.
drivers/built-in.o: In function `qxl_display_read_client_monitors_config':
(.text+0x19d754): undefined reference to `crc32_le'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
With CONFIG_DYNAMIC_DEBUG=y, the following compile error occurs:
drivers/gpu/drm/tegra/mipi-phy.c: In function ‘mipi_dphy_timing_validate’:
drivers/gpu/drm/tegra/mipi-phy.c:69:11: error: ‘EINVAL’ undeclared (first use in this function)
drivers/gpu/drm/tegra/mipi-phy.c:69:11: note: each undeclared identifier is reported only once for each function it appears in
Fix this by directly including the header that defines EINVAL.
Fixes: dec727399a ("drm/tegra: Add DSI support")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Implement very basic PRIME support. This currently only works with
buffers that are contiguous in memory and will refuse to import any
physically non-contiguous buffers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Some of the code in the CRTC's mode setting code is specific to the RGB
output or needs to be called slightly differently depending on the type
of output. Push that code down into the output drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra124 and later support interlacing, but the driver doesn't support
it yet. Make sure interlacing stays disabled on hardware that supports
it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
If we don't have enough memory for ->planes then we leak "fb".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
A lot of the modern userspace is capable of working without the legacy
fbdev support. kmscon can be used as a replacement for the framebuffer
console, and KMS X drivers create their own framebuffers.
Most people don't have a system where all of this works yet, though, so
leave support enabled by default.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In case of error, the devm_ioremap_resource() function returns ERR_PTR()
and never NULL. The NULL test in the return value check should therefore
be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit adds support for both DSI outputs found on Tegra. Only very
minimal functionality is implemented, so advanced features like ganged
mode won't work.
Due to the lack of other test hardware, some sections of the driver are
hardcoded to work with Dalmore.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When an output is disabled, its DPMS mode is usually set to off. Instead
of only disabling the panel (if one is attached), turn the output off
entirely to save more power.
HDMI doesn't have any panels attached, so it previously didn't save any
power at all. With this commit, however, the complete HDMI interface
will be turned off, therefore allowing an attached monitor to go into a
standby mode.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DRM core doesn't track enable and disable state of encoders and/or
connectors, so calls to the output's .enable() and .disable() are not
guaranteed to be balanced. Track the enable state internally so that
calls to regulator and clock frameworks remain balanced.
Signed-off-by: Thierry Reding <treding@nvidia.com>
These buffer object operations are never used outside of the GEM
implementation so there is no use in exporting them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The ARCH_MULTIPLATFORM dependency was introduced back when Tegra didn't
support multiplatform yet as a means to allow the driver to be easily
compile-tested along with other DRM drivers. In the meantime, the new
COMPILE_TEST Kconfig option has been introduced for exactly that
purpose, so use that instead to clarify the intention.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra124 has 192 syncpoints whereas its predecessors had 32 syncpoints.
This required changes to the hardware register layout.
Signed-off-by: Arto Merilainen <amerilainen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Treat both negative and zero return values from clk_round_rate() as
errors. This is needed since subsequent patches will convert
clk_round_rate()'s return value to be an unsigned type, rather than a
signed type, since some clock sources can generate rates higher than
(2^31)-1 Hz.
Eventually, when calling clk_round_rate(), only a return value of zero
will be considered a error. All other values will be considered valid
rates. The comparison against values less than 0 is kept to preserve
the correct behavior in the meantime.
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Mikko Perttunen <mperttunen@nvidia.com>
Cc: Arto Merilainen <amerilainen@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Terje Bergström <tbergstrom@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When debugfs support isn't enabled, gcc complains about some variables
being unused. To avoid further #ifdefery, move debugfs specific setup
code into static functions and use IS_ENABLED(CONFIG_DEBUG_FS) to have
the compiler, rather than the preprocessor, discard them when unused.
The advantage of doing it this way is that all the code will be
compile-tested whether or not debugfs support is enabled.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The ARCH_MULTIPLATFORM dependency was introduced back when Tegra didn't
support multiplatform yet as a means to allow the driver to be easily
compile-tested along with other DRM drivers. In the meantime, the new
COMPILE_TEST Kconfig option has been introduced for exactly that
purpose, so use that instead to clarify the intention.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Include the linux/host1x.h and dev.h headers so that function prototypes
are visible to keep sparse from suggesting that their implementations be
made static.
Signed-off-by: Thierry Reding <treding@nvidia.com>
An earlier patch added a subset of the required HW specific header files
but didn't actually include the right ones when compiling for host1x02.
Signed-off-by: Thierry Reding <treding@nvidia.com>
But only when we indeed set up a gtt mapping. We need this since the
vma also holds a pages_pin_count, on top of the unconditional
pages_pin_count we grab for all stolen objects (to avoid swap-out).
This should avoid a pages_pin_count underrun when cleaning up
framebuffers objects taken over from the BIOS.
Chris mentioned in his review that this bug even predates the vma
conversion.
Reported-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drivers/gpu/drm/r128/r128_state.c:1014:10-17: WARNING opportunity for memdup_user
/c/kernel-tests/src/cocci/drivers/gpu/drm/r128/r128_state.c:1029:9-16: WARNING opportunity for memdup_user
/c/kernel-tests/src/cocci/drivers/gpu/drm/r128/r128_state.c:904:10-17: WARNING opportunity for memdup_user
/c/kernel-tests/src/cocci/drivers/gpu/drm/r128/r128_state.c:914:9-16: WARNING opportunity for memdup_user
Use memdup_user rather than duplicating its implementation
This is a little bit restricted to reduce false positives
Generated by: coccinelle/api/memdup_user.cocci
CC: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is just used for a debugfs file, and we can easily reconstruct
this number by just walking the list twice. Which isn't really bad for
a debugfs file anyway.
So let's rip this out.
There's the other issue that the dev->vmalist itself is a bit useless,
since that can be reconstructed with all the memory mapping
information from proc. But remove that is a different topic entirely.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It's racy, and it's only used in debugfs. There are simpler ways to
know whether something is going on (like looking at dmesg with full
debugging enabled). And they're all much more useful.
So let's just rip this out.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Now dev->ioctl_count tries to prevent the device from disappearing if
it's still in use. And if we'd actually need this code it would be
hopelessly racy and broken.
But luckily the vfs already takes care of this. So we can just rip it
out.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This has the nice advantage that we'll get rid of a DRM_WAIT_ON user
for free.
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Checking directly for the right capability is simpler. Also this rids
us of a few places that use DRM_CURRENTPID.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The real linux interfaces are soooo much easier on the eyes ...
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
I've killed them a long time ago in drm/i915, let's get rid of this
remnant of shared drm core days for good.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We don't have any userspace interfaces that use HZ as a time unit, so
having our own DRM define is useless.
Remove this remnant from the shared drm core days.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The <linux/agp_backend.h> header provides dummy functions and
fallbacks, so no need for screaming macros.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
David Herrmann dutifully moved this locking along when moving the
agp_init call out of the generic drm_dev_register into the pci
specific load helpers.
But afaict there's no need and the reason for that locking has been
purely a historical accident - we need the lock around the driver dev
node registration to paper over the midlayer init races, and the agp
init simply ended up in there. The real fix for all this is of course
to delay the dev (and sysfs/debugfs) interface registration until
everything is fully set up.
Until then stop the cargo-cult locking from spreading and remove the
locking.
Cc: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Call drm_pci_agp_destroy directly, there's no point in the
indirection. Long term we want to shuffle this into each driver's
unload logic, but that needs cleared-up drm lifetime rules first.
v2: Add a dummy function for !CONFIG_PCI, spotted my David Herrmann.
v3: Fixup for the coding style police.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Cc: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Wrapping a kfree is pointless.
v2: Add a comment to the kerneldoc for drm_agp_init to explain where
the kfree happens as requested by David. Note that for modeset drivers
agp cleanup is fairly complicated anyway: The drm_agp_clear is a noop
and drivers must call drm_agp_release on their own. Which they all
seem to do properly.
Cc: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The PCI bus helper is the only user of it. Call it directly before
device-registration to get rid of the callback.
Note that all drm_agp_*() calls are locked with the drm-global-mutex so we
need to explicitly lock it during initialization. It's not really clear
why it's needed, but lets be safe.
v2: Rebase on top of the agp_init interface change.
v3: Remove the rebase-fail where I've accidentally killed the ->irq_by_busid
callback a bit too early.
Cc: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Most place actually want to just check for dev->agp (most do, but a
few don't so this fixes a few potential NULL derefs). The only
exception is the agp init code which should check for the AGP driver
feature flag.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Thanks to the removal of REQUIRE_AGP we can use a void return value
and shed a bit of complexity.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Only the two intel drivers need this and they can easily check for
working agp support in their driver ->load callbacks.
This is the only reason why agp initialization could fail, so allows
us to rip out a bit of error handling code in the next patch.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should be
replaced with IS_ERR(). Also remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
[Remove the unneeded mem == NULL check]
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The current values seem to be defined in a format that's specific to the
i915, gma500 and radeon drivers. To make this more generally useful, use
the values as defined in the specification.
While at it, prefix the constants with DP_ for improved namespacing.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Gone with the new gem vma offset manager from David.
We can also ditch the uapi header definition from the enum since
userspace never used this. It ended up in there purely for historical
reasons (for reusing the old drm mmap code essentially), not because
userspace ever needed it.
Cc: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There's really no need for the drm core to keep a list of all
devices of a given driver - the linux device model keeps perfect
track of this already for us.
The exception is old legacy ums drivers using pci shadow attaching.
So rename the lists to make the use case clearer and rip out everything
else.
v2: Rebase on top of David Herrmann's drm device register changes.
Also drop the bogus dev_set_drvdata for platform drivers that somehow
crept into the original version - drivers really should be in full
control of that field.
v3: Initialize driver->legacy_dev_list outside of the loop, spotted by
David Herrmann.
v4: Rebase on top of the newly created host1x drm_bus for tegra.
Cc: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This very much looks like a remnant of the old legady ums shadow
attach days. Now with the last users gone we can rip it out since
we won't ever support an ums drm driver again.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The drvdata pointer is already assigned to something useful.
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Again no apparent user of the driver data field.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We need to chase one pointer here.
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Again omap already sets the driver data pointer to the drm_device.
Also drop the driver unregister call, that should be (and already is)
done in the module unload hook.
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
tilcdc already stores the drm_device in the driver data pointer. So
use that.
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
I didn't find any user of the driver data yet, so store the
drm_device pointer in there.
Cc: Inki Dae <inki.dae@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The magic dance drm_platform_exit does is actually a remnant of the
old legacy shadow attach support for platform devices. Modern modesetting
drm drivers shouldn't do this any more (and usb/pci devices actually don't
do this).
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The clk_prepare_enable() call can fail. Check it's return value. We
can't propagate it all the way to the user as the KMS operations in
which the clock is enabled return a void.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Not all drivers will need take all the modeset locks for dirtyfb, so
push the locking down to the drivers.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There's no reason to keep a reference to objects in the name idr. Each
handle to an object has a reference to the object and just before we
destroy the last handle we take the object out of the name idr. Thus,
if an object is in the name idr, there's at least one reference to the
object.
Or to put it another way, the name idr reference will never keep the
object alive. It just looks like it, which is confusing.
Signed-off-by: Kristian Høgsberg <krh@bitplanet.net>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Sometimes we want to disable all the screens on a system, because that
will allow the graphics card to be put into low-power states. The
problem is that, for example, while all screens are disabled, if we
get a hotplug interrupt, fbcon will decide to set a mode instead of
keeping everything disabled, which will remove us from our low power
states.
Let's assume that if there's a DRM master, it will be able to do
whatever is appropriate when we get the hotplug.
This problem can be reproduced by the runtime PM test program from
intel-gpu-tools: we disable all the screens so the graphics device can
be put into D3, then something triggers a hotplug interrupt, fbcon
sets a mode and breaks our test suite. The problem can be reproduced
more easily by the "i2c" subtest.
Other approaches considered for the problem:
- Return "false" if "bound == 0" and the caller of
drm_fb_helper_is_bound is a hotplug handler. This would break
the case where the machine boots with no outputs connected, then
the user plugs a monitor.
- Add a new IOCTL to force fbcon to not set modes. This would keep
all the current applications behaving the same, but adding a new
IOCTL is not always the greatest idea.
- Return false only if "dev->primary->master && bound == 0". This
was my first implementation, but Chris suggested we should do
the check irrespective of the "bound" variable.
Thanks to Daniel Vetter for the investigation, ideas and the
implementation of the hotplug alternative.
v2: - Do the check first, irrespective of "bound".
- Cc dri-devel
Cc: dri-devel@lists.freedesktop.org
Credits-to: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Otherwise we risk that the 2nd part of the line ends up on a line of
it's own, which means a kernel dmesg line without a log level. This
then upsets the dmesg checker in piglit.
Only really happens in some of the truly nasty igt testcases which
race cache dropping (through debugfs) with other gem operations.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Always use "void *" for arbitrary memory buffers, as this allows to drop
casts in assignments.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- some more ppgtt prep patches from Ben
- a few fbc fixes from Ville
- power well rework from Imre
- vlv forcewake improvements from Deepak S, Ville and Jesse
- a few smaller things all over
[airlied: fixup forwcewake conflict]
* tag 'drm-intel-next-2013-11-29' of git://people.freedesktop.org/~danvet/drm-intel: (97 commits)
drm/i915: Fix port name in vlv_wait_port_ready() timeout warning
drm/i915: Return a drm_mode_status enum in the mode_valid vfuncs
drm/i915: add intel_display_power_enabled_sw() for use in atomic ctx
drm/i915: drop DRM_ERROR in intel_fbdev init
drm/i915/vlv: use parallel context restore when coming out of RC6
drm/i915/vlv: use a lower RC6 timeout on VLV
drm/i915/sdvo: Fix up debug output to not split lines
drm/i915: make sparse happy for the new vlv mmio read function
drm/i915: drop the right force-wake engine in the vlv mmio funcs
drm/i915: Fix GT wake FIFO free entries for VLV
drm/i915: Report all GTFIFODBG errors
drm/i915: Enabling DebugFS for valleyview forcewake counts
drm/i915/vlv: Valleyview support for forcewake Individual power wells.
drm/i915: Add power well arguments to force wake routines.
drm/i915: Do not attempt to re-enable an unconnected primary plane
drm/i915: add a debugfs entry for power domain info
drm/i915: add a default always-on power well
drm/i915: don't do BDW/HSW specific powerdomains init on other platforms
drm/i915: protect HSW power well check with IS_HASWELL in redisable_vga
drm/i915: use IS_HASWELL/BROADWELL instead of HAS_POWER_WELL
...
Conflicts:
drivers/gpu/drm/i915/intel_display.c
The GMCH_CTRL register (or MGCC in the spec) is at a different address
on Sandybridge, and the address to which we currently write to is
undefined. These stray writes appear to upset (hard hang) my Ivybridge
machine whilst it is in UEFI mode.
Note that the register is still marked as locked RO on Sandybridge, so
vgaarb is still dysfunctional.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We use this hook starting from ILK onwards, so change the prefix
accordingly. Also rename functions/struct names used from
haswell_update_wm that are relevant to ILK already.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the DRM panel framework to attach a panel to an output. If the panel
attached to a connector supports supports the backlight brightness
accessors, a property will be available to allow the brightness to be
modified from userspace.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a driver for simple panels. Such panels can have a regulator that
provides the supply voltage and a separate GPIO to enable the panel.
Optionally the panels can have a backlight associated with them so it
can be enabled or disabled according to the panel's power management
mode.
Support is added for two panels: An AU Optronics 10.1" WSVGA and a
Chunghwa Picture Tubes 10.1" WXGA panel.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a very simple framework to register and lookup panels. Panel drivers
can initialize a DRM panel and register it with the framework, allowing
them to be retrieved and used by display drivers. Currently only support
for DPMS and obtaining panel modes is provided. However it should be
sufficient to enable a large number of panels. The framework should also
be easily extensible to support more sophisticated kinds of panels such
as DSI.
The framework hasn't been tied into the DRM core, even though it should
be easily possible to do so if that's what we want. In the current
implementation, display drivers can simple make use of it to retrieve a
panel, obtain its modes and control its DPMS mode.
Note that this is currently only tested on systems that boot from a
device tree. No glue code has been written yet for systems that use
platform data, but it should be easy to add.
Signed-off-by: Thierry Reding <treding@nvidia.com>
MIPI DSI bus allows to model DSI hosts and DSI peripherals using the
Linux driver model. DSI hosts are registered by the DSI host drivers.
During registration DSI peripherals will be created from the children
of the DSI host's device tree node. Support for registration from
board-setup code will be added later when needed.
DSI hosts expose operations which can be used by DSI peripheral drivers
to access associated devices.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=8T7+
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.14-dmas-resets-rework' into drm/for-next
ARM: tegra: implement common DMA and resets DT bindings
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
Spread spectrum seems to cause hangs when dynamic clock
switching is enabled. Disable it for now. This does not
affect performance or the amount of power saved. Tracked
down by Martin Andersson.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=69723
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Apparently always enabling the sprite scaler magically made
sprites work on ILK in the past.
I think the real reason for the failure was missing sprite
watermark programming, and enabling the scaler effectively
disabled LP1+ watermarks, which was enough to keep things going.
Or it might be that the hardware more or less ignores watermarks
for scaled sprites since things seem to work even if I leave
sprite watermarks at 0 and disable all other planes except the
sprite.
In any case, we left the scaler always on but then failed to
check whether we might be exceeding the scaler's source size
limits. That caused the sprite to fail when a sufficiently
large unscaled image was being displayed.
Now that we're getting proper watermark programming for ILK, we
can keep the scaler disabled unless we need to do actual scaling.
This reverts commit 8aaa81a166.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter