The AR9330 1.0 and 1.1 are using the same revision,
thus it is not possible to distinguish the two chips.
The platform setup code can distinguish the chips based
on the SoC revision.
Add a callback function to ath9k_platform_data in order
to allow getting the revision number from the platform code.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
higher the chainmask, lesser the power_delta to be added
to the paprd_training_power
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the new consistent dump feature from (generic) netlink
to advertise when dumps are incomplete.
Readers may note that this does not initialize the
rdev->bss_generation counter to a non-zero value. This is
still OK since the value is modified only under spinlock
when the list is modified. Since the dump code holds the
spinlock, the value will either be > 0 already, or the
list will still be empty in which case a consistent dump
will actually be made (and be empty).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some cases local pointers are used to cast void pointers passed to
the function. Those unnecessary local pointers are also removed.
This patch was inspired by Joe Perches' patch
[PATCH net-next 1/2] wireless: Remove casts of void *;
and the comments from Julian Calaby.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Cc: Joe Perches <joe@perches.com>
Cc: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As USB_INT_ID_RETRY_FAILED can override USB_INT_ID_REGS, beacon interrupt
(CR_INTERRUPT) might be lost. Problem is that when device trigger CR_INTERRUPT
it disables HW interrupt. Now if USB_INT_ID_REGS with CR_INTERRUPT gets lost,
beacon interrupt stays disabled until beacon watchdog notices the stall. This
happen very often on heavy TX. Improve watchdog to trigger earlier, after three
missing beacon interrupts.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
zd_mac_config_beacon() has only limited time to set up beacon when called from
beacon interrupt handler/worker. So do not let it retry acquiring beacon fifo
semaphore in interrupt handler. Beacon fifo semaphore should not be locked by
firmware anyway at this time, it's only locked when device is using/txing
beacon.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Device losses read-reg interrupts. By looking at usbmon it appears that
USB_INT_ID_RETRY_FAILED can override USB_INT_ID_REGS. This causes read
command to timeout, usually under heavy TX.
Fix by retrying read registers again if USB_INT_ID_RETRY_FAILED is received
while waiting for USB_INT_ID_REGS.
However USB_INT_ID_REGS is not always lost but is received after
USB_INT_ID_RETRY_FAILED and is usually received by the retried read
command. USB_INT_ID_REGS of the retry is then left unhandled and might
be received by next read command. Handle this by ignoring previous
USB_INT_ID_REGS that doesn't match current read command request.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update HW beacon only when needed. This appears to make device work in AP-mode
(dtim_period=1) somewhat more stable.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This message is should be debug-only as it tells almost nothing useful. It also
happens very often and just floods logs.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver uses IEEE80211_HW_SIGNAL_UNSPEC and so signal values reported to
mac80211 should be in range 0..100. Sometimes device return out of range
values. These out of range values can then trigger warning in
cfg80211_inform_bss_frame.
This patch adds checks to enforce range returned from driver to
mac80211 be in 0..100 range.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Consider the following situation:
* a dump that would show 8 entries, four in the first
round, and four in the second
* between the first and second rounds, 6 entries are
removed
* now the second round will not show any entry, and
even if there is a sequence/generation counter the
application will not know
To solve this problem, add a new flag NLM_F_DUMP_INTR
to the netlink header that indicates the dump wasn't
consistent, this flag can also be set on the MSG_DONE
message that terminates the dump, and as such above
situation can be detected.
To achieve this, add a sequence counter to the netlink
callback struct. Of course, netlink code still needs
to use this new functionality. The correct way to do
that is to always set cb->seq when a dumpit callback
is invoked and call nl_dump_check_consistent() for
each new message. The core code will also call this
function for the final MSG_DONE message.
To make it usable with generic netlink, a new function
genlmsg_nlhdr() is needed to obtain the netlink header
from the genetlink user header.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After uploading radio values calibration goes in. In MMIO dump it is:
radio_read(0x002b) -> 0x0008
radio_write(0x002b) <- 0x0008
radio_read(0x002e) -> 0x0004
radio_write(0x002e) <- 0x0000
radio_read(0x002e) -> 0x0000
radio_write(0x002e) <- 0x0004
radio_read(0x002b) -> 0x0008
radio_write(0x002b) <- 0x0009
To find masks and sets, MMIO hacks were used to fool closed driver.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When module is reloaded, device may fail to work, with messages:
[ 342.211926] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x0059, type=2.
[ 342.314254] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x004a, type=2.
[ 342.416458] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 3183 max 2432.
[ 342.518605] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x00c9, type=2.
[ 342.620836] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x00ae, type=1.
[ 342.723201] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 0 max 2432.
[ 342.825399] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 0 max 2432.
[ 342.927624] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 0 max 2432.
[ 343.029804] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 2491 max 2432.
[ 343.132008] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 2576 max 2432.
[ 343.234326] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x004c, type=1.
[ 343.438723] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x00e6, type=1.
Whereas replugging device make it functional. To solve that problem
force reset device during probe.
With patch messages are gone. Unfortunately device may sometimes
still does not operate correctly after module reload (fail to receive
data after associate), but such cases are rarer than without the patch.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes rxdesc descriptor provided by hardware contains invalid
(random) data. For example rxdesc.size can be bigger than actual
size of the buffer. When this happen rt2x00crypto_rx_insert_iv()
corrupt memory doing memmove outside of buffer boundaries.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Switching channel happens after specific SHM write to B43_SHM_SH_CHAN.
This is the way we found it in BCM4331 MMIO dumps. By comparing with
N-PHY code we noticed there is routing used for SYN and TX/RX.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The trick was to find 0x810 PHY reg ops close to analog enabling code.
To find out proper masks and sets, MMIO hacks were used.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Closed drivers kill radio right after reading radio version and MACCTL,
so it was easy to find related PHY ops:
phy_read(0x0810) -> 0x0000
phy_write(0x0810) <- 0x0000
To find out the mask of above OP, MMIO hack was used to fake read val:
phy_read(0x0810) -> 0xffff
phy_write(0x0810) <- 0x0000
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the connection is ready we should set the connection
to CONNECTED so userspace can use it.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
These are a potential source of confusion, as most C code treats all
non-zero values as true.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rtl_ps_set_rf_state's protect_or_not parameter is not set to
true anywhere, except for commented out code.
It enables some legacy locking code, which is no longer used,
so delete the parameter and the old locking code.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
offchan_deley should be offchan_delay
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Function managing IRQs is needed for external drivers like b43.
On the other side we do not expect writing any hosts drivers outside of
bcma, so this is safe to do not export functions related to this.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nothing else is freeing it, and this mirrors the error handling path
already in ath5k_init_softc.
https://bugzilla.kernel.org/show_bug.cgi?id=37592
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Tsyvarev Andrey <tsyvarev@ispras.ru>
checking the status of PAPRD_AGC2_POWER(Log(ADC_power) measured after
last gain-change in dB) field suggests whether the PAPRD is completely/properly
done. This is an additional check apart from polling for PAPRD done bit being set.
Susinder suggests that the ideal power range value should be
0xf0 to 0xfe. With AR9382 we do have the values in this range. to have a
common check for all platforms we take agc2_power should be atleast greater
than 0xe0
Cc: susinder@qca.qualcomm.com
Cc: senthilb@qca.qualcomm.com
Cc: kmuthusa@qca.qualcomm.com
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
when the AP is configured with HT40/2.4GHz and when PAPRD is enabled in station
we have PAPRD training frames never sent out because of the following
failure "PAPRD target power delta out of range". This consistently happens
in channel 10,11 in Over The Air testing and rarely in channel 6 under wired
setup.
the reason behind this issue is all the HT40 rates target power
are 0 when we operate in channel 10/11 at 2.4GHz
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We already have access to the chan, we don't have to access the
socket to get its imtu.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
We should not try to do any other type of configuration for
LE links when they become ready.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
core.h references ieee80211_ops but doesn't include mac80211.h, which issues
a warning once mac80211-compat.h is taken into use.
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
zd_chip.h contains one function with a pointer to ieee80211_hw but doesn't
include mac80211.h. As a temporary solution include mac80211.h to avoid
a warning.
Signed-off-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hacks break once mac80211-compat.h is taken into use. Fix it by adding
an ifdef check.
Signed-off-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hacks break once mac80211-compat.h is taken into use. Fix it by adding
an ifdef check.
Signed-off-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos