Add the AO and EE domain CEC pins for the Amlogic Meson GXBB SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The AO SPDIF pins were incorrectly defined with the EE pin offset.
Fixes: b840d649f9 ("pinctrl: meson: gxl: add spdif output pins")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The AO I2S pins were incorrectly defined with the EE pin offset.
Fixes: 2899adf042 ("pinctrl: meson: gxl: add i2s output pins")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIODV_18 entry was missing in the original driver push.
Fixes: 468c234f9e ("pinctrl: amlogic: Add support for Amlogic Meson GXBB SoC")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fixups here tend to be more of a conglomerate of some of the other
repeated/systematic ones we've seen in the earlier pinctrl cleanups.
We remove module.h from code that isn't doing anything modular at
all; if they have __init sections, then replace it with init.h
One driver has a .remove that would be dispatched on module_exit,
and as that code is essentially orphaned, so we remove it. In case
anyone was previously doing the (pointless) unbind to get to that
function, we disable unbind for this one driver as well.
A couple bool drivers (hence non-modular) are converted over to
to builtin_platform_driver().
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Eric Anholt <eric@anholt.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jon Mason <jonmason@broadcom.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Sherman Yin <syin@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-gpio@vger.kernel.org
Cc: linux-rpi-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
None of the Kconfigs for any of these drivers are tristate,
meaning that they currently are not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the drivers there is no doubt they are builtin-only. All
drivers get similar changes, so they are handled in batch.
We remove module.h from code that isn't doing anything modular at
all; if they have __init sections, then replace it with init.h.
A couple drivers have module_exit() code that is essentially orphaned,
and so we remove that.
Quite a few bool drivers (hence non-modular) are converted over to
to builtin_platform_driver().
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Pritesh Raithatha <praithatha@nvidia.com>
Cc: Ashwini Ghuge <aghuge@nvidia.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use of_device_get_match_data() instead of of_match_device().
It allows us to remove the forward declaration of pcs_of_match.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are a couple of issues with group_desc initialization in function
zx_pinctrl_build_state().
- num_pins is not initialized and remains zero.
- pins shouldn't be initialized with a pointer to variable in the
stack.
With them fixed, pin_request() in pinmux_enable_setting() can be invoked
correctly.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SPICC controller has dedicated SPI pins, this patchs add the pins
definition in the GXBB pinctrl driver
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SPICC controller has dedicated SPI pins, this patchs add the pins
definition in the GXL pinctrl driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We use well known standard names for functions that have name, such as
I2C, SPI, SPDIF, etc..
Fix the function name of SPDIF, which was named OWA (One Wire Audio)
based on Allwinner datasheets.
Fixes: 4730f33f0d ("pinctrl: sunxi: add allwinner A83T PIO controller
support")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver supports using mcp23xxx as interrupt controller, so
let's drop all comments stating otherwise.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves irq property handling from spi/i2c specific code into
the generic mcp23s08_probe_one. This is possible because the
device properties are named equally.
As a side-effect this drops support for setting the properties via
pdata, which has no mainline users. If boardcode wants to enable
the chip as interrupt controller it can attach the device properties
instead.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Simplify spi pdata handling, so that it uses pdata when available
and falls back to reading device properties otherwise.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Simplify i2c pdata handling, so that it uses pdata when available
and falls back to reading device properties otherwise.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Switching to devm_gpiochip_add_data simplifies the driver's
cleanup routine and safes a few loc.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Let's remove a few lines of code by using managed memory for mcp
variable.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
i2c-core and spi-core already assign the irq, so we
can drop the additional call from the mcp driver.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver compiles & works perfectly fine without OF_GPIO on x86,
so lets drop the dependency.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of using custom caching, this switches to regmap based
caching. Before the conversion the debugfs file used uncached
values, so that it was easily possible to see power-loss related
problems. The new code will check and recover at this place.
The patch will also ensure, that irqs are not cleared by checking
register status in debugfs.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
mcp23s08 support configuration of the pullups using the
pinconf framework. This removes the custom pullup configuration
from platform data, which has no upstream users.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
mcp23xxx device have configurable 100k pullup resistors. This adds
support for enabling them using pinctrl's pinconf interface.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the mcp23s08 driver from gpio to pinctrl. Actual
pinctrl support for configuration of the pull-up resistors
follows in its own patch.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver handles pin configuration and pin muxing for the
JZ4740 and JZ4780 SoCs from Ingenic.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When pinctrl device registers, it automatically claims hogs, that is,
maps that pinctrl device serves for itself.
It is possible that in addition to SoC's pinctrl device, other pinctrl
devices get registered. E.g. some gpio expander devies are registered
as pinctrl devices. For such devices, pinctrl maps could be defined
that set up SoC's pins (e.g. interrupt pin for gpio expander). Such
a map will have target device set to gpio expander.
Here is device tree snippet that causes this scenario:
&i2c0 {
sx1503@20 {
compatible = "semtech,sx1503q";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sx1503_20>;
...
};
};
...
&iomuxc {
pinctrl_sx1503_20: pinctrl-sx1503-20 {
fsl,pins = <
VF610_PAD_PTB1__GPIO_23 0x219d
>;
};
};
Such a map will have target device set to gpio expander. However is not
a hog, it is a regular map that is claimed by core before gpio expander
device is probed.
Thus when looking for hogs, it is not enough to check that map's target
device is set to pinctrl device being registered. Need also check that
map's control device is also set to the same.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
MX7ULP MUX mode mask and shift bit is different from VF610.
Let's make it a platform specific property for the later easy of
adding MX7ULP support.
One trick in exist code that Vybrid hardcoded the config part
as 0xffff because its mux_config register BIT[15-0] are all configs
part. But it's not true in ULP, so use mux_mask instead to address
the difference.
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The design is based on the exist architecture that the core will
provide a uniformed way to decode the generic pin config into platform
config register raw data according to the imx_cfg_params_decode maps
registered by platform.
Two useful macros, IMX_CFG_PARAMS_DECODE and IMX_CFG_PARAMS_DECODE_INVERT,
are created for platform to register decode map conveniently.
In order to cope with some special case, a platform specific fixup()
function is also available to use.
Note that rather than fully utilizing the generic pinconf support
provided by pinctrl core, IMX only adopts the device tree bindings
of generic pinconf. The config used in .pin_config_get[set] are raw
register data instead of generic one which makes us align the exist
using. And that's also why we cannot set pinconf_ops.is_generic.
Cc: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The original implemented debug message does not work for
SHARE_MUX_CONF_REG case. This patch fixes it.
Fixes: bf5a530971 ("pinctrl: imx: add VF610 support to imx pinctrl framework")
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If 'devm_kzalloc' fails, a NULL pointer will be dereferenced.
Return -ENOMEM instead, as done for the other memory allocation just a
few lines below.
BTW, change the 'devm_kzalloc' into a 'devm_kcalloc'.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
mt7623 pinctrl hardware can be compatible with mt2701 driver,
so the patch lets the pinctrl on mt7623 SoC reuse the driver
and deletes those redundant ones.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds another missing pin found in the Meson8 SoCs. Currently
there's no driver which would use this pin yet.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds another missing pin found in the Meson8 SoCs. Currently
there's no driver which would use this pin yet.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for the I2S and SPDIF input and output pins, similar
to what we have on GXBB and GXL.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the missing pins for the PWM controllers found in Amlogic
Meson8 SoCs. This includes the pins for PWM_A, PWM_B, PWM_C, PWM_D,
PWM_E and PWM_F controllers.
There is an additional PWM function with the name PWM_VS in the vendor
kernel sources which seems to be used for external video input. Thus
it's not part of this change as the IP block behind the pwm-meson driver
is not responsible for these pins.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit
The script “checkpatch.pl” pointed information out like the following.
Comparison to NULL could be written …
Thus fix the affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A single character (line break) should be put into a sequence.
Thus use the corresponding function "seq_putc".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The script "checkpatch.pl" pointed information out like the following.
CHECK: spaces preferred around that '+' (ctx:VxV)
Thus fix the affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The script "checkpatch.pl" pointed information out like the following.
WARNING: quoted string split across lines
Thus fix the affected source code place.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit
The script “checkpatch.pl” pointed information out like the following.
Comparison to NULL could be written !…
Thus fix the affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Strings which did not contain data format specifications should be put
into a sequence. Thus use the corresponding function "seq_puts".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Updating the point of contact for AMD GPIO driver.
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Cc: Ken Xue <Ken.Xue@amd.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A single character (line break) should be put into a sequence.
Thus use the corresponding function "seq_putc".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Armada 37xx SoCs can handle interrupt through GPIO. However it can
only manage the edge ones.
The way the interrupt are managed is classical so we can use the generic
interrupt chip model.
The only unusual "feature" is that many interrupts are connected to the
parent interrupt controller. But we do not take advantage of this and use
the chained irq with all of them.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pin controller on ZTE ZX platforms is kinda of hybrid. It consists
of a main controller and an auxiliary one. For example, on ZX296718 SoC,
the main controller is TOP_PMM and the auxiliary one is AON_IOCFG. Both
controllers work together to control pin multiplexing and configuration.
For most of pins, the pinmux function is controlled by main controller
only, and this type of pins are meant by term 'TOP pins'. For other
pins, the pinmux is controlled by both main and auxiliary controllers,
as the available multiplexing functions for the pin spread in both
controllers. This type of pins are called 'AON pins'. Though pinmux
implementation is quite different, pinconf is same for both types of
pins. Both are controlled by auxiliary controller, i.e. AON_IOCFG on
ZX296718.
The patch adds the ZTE ZX core pinctrl driver to support this hybrid
pin controller as well as ZX296718 SoC specific pin data.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Neil Armstrong