Andreas Schwab spotted that recent kernels broke reporting of the PowerMac
machine model in /proc/cpuinfo. This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes the following BUG message of arch/m32r/smp.c for
CONFIG_DEBUG_PREEMPT:
BUG: using smp_processor_id() in preemptible
This message is displayed by an smp_processor_id() execution during
kernel's preemptible-state.
Signed-off-by: Hitoshi Yamamoto <hitoshiy@isl.melco.co.jp>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
arch/mips/pci/fixup-tb0226.c: In function `pcibios_map_irq':
arch/mips/pci/fixup-tb0226.c:31: warning: implicit declaration of function `vr41xx_set_irq_trigger'
arch/mips/pci/fixup-tb0226.c:32: error: `TRIGGER_LEVEL' undeclared (first use in this function)
arch/mips/pci/fixup-tb0226.c:32: error: (Each undeclared identifier is reported only once
arch/mips/pci/fixup-tb0226.c:32: error: for each function it appears in.)
arch/mips/pci/fixup-tb0226.c:33: error: `SIGNAL_THROUGH' undeclared (first use in this function)
arch/mips/pci/fixup-tb0226.c:34: warning: implicit declaration of function `vr41xx_set_irq_level'
arch/mips/pci/fixup-tb0226.c:34: error: `LEVEL_LOW' undeclared (first use in this function)
Signed-off-by: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Doing a "SUNW,stop-self" firmware call on the other cpus is not the
correct thing to do when dropping into the firmware for a halt,
reboot, or power-off.
For now, just do nothing to quiet the other cpus, as the system should
be quiescent enough. Later we may decide to implement smp_send_stop()
like the other SMP platforms do.
Based upon a report from Christopher Zimmermann.
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Richard Purdie
Remove a couple of lines of accidently added code causing compile
errors.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Update corgi_lcd to use bus_find_device to locate the pxafb device
hence fixing a compile error.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add a function to allow machines to set the parent of the pxa
framebuffer device. This means the power up/down sequence can be
controlled where required by the machine.
Update spitz to use the new function, fixing a compile error.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
This patch fixes L7200 so that it builds in 2.6.latest. I do not
have the hardware so don't know if it actually still works, but
the changes are fairly trivial. I am not even sure if anyone
still maintains, uses, or cares about this machine type.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The hairy fast allocator in the sparc64 PCI IOMMU code
has a hard limit of 256 pages. Certain devices can
exceed this when performing very large I/Os.
So replace with a more simple allocator, based largely
upon the arch/ppc64/kernel/iommu.c code.
Signed-off-by: David S. Miller <davem@davemloft.net>
All the PCI controller drivers were doing the same thing
setting up the IOMMU software state, put it all in one spot.
Signed-off-by: David S. Miller <davem@davemloft.net>
Original patch by Harald Welte, with feedback from Herbert Xu
and testing by Sbastien Bernard.
EBTABLES, ARP tables, and IP/IP6 tables all assume that cpus
are numbered linearly. That is not necessarily true.
This patch fixes that up by calculating the largest possible
cpu number, and allocating enough per-cpu structure space given
that.
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Nicolas Pitre
... and therefore should not live in the .text section.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The Simtec EB2410ITX (BAST) has a PC/104 slot, and
therefore we should enable CONFIG_ISA to allow the
drivers for ISA peripherals to be selected
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Remove an unused variable from s3c2410.c and
ensure that items not needed to be exported from
s3c2440.c are declared static.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sequence to move over to the Linux trap tables from
the firmware ones needs to be more air tight. It turns
out that to be %100 safe we do need to be able to translate
OBP mappings in our TLB miss handlers early.
In order not to eat up a lot of kernel image memory with
static page tables, just use the translations array in
the OBP TLB miss handlers. That solves the bulk of the
problem.
Furthermore, to make sure the OBP TLB miss path will work
even before the fixed MMU globals are loaded, explicitly
load %g1 to TLB_SFSR at the beginning of the i-TLB and
d-TLB miss handlers.
To ease the OBP TLB miss walking of the prom_trans[] array,
we sort it then delete all of the non-OBP entries in there
(for example, there are entries for the kernel image itself
which we're not interested in at all).
We also save about 32K of kernel image size with this change.
Not a bad side effect :-)
There are still some reasons why trampoline.S can't use the
setup_trap_table() yet. The most noteworthy are:
1) OBP boots secondary processors with non-bias'd stack for
some reason. This is easily fixed by using a small bootup
stack in the kernel image explicitly for this purpose.
2) Doing a firmware call via the normal C call prom_set_trap_table()
goes through the whole OBP enter/exit sequence that saves and
restores OBP and Linux kernel state in the MMUs. This path
unfortunately does a "flush %g6" while loading up the OBP locked
TLB entries for the firmware call.
If we setup the %g6 in the trampoline.S code properly, that
is in the PAGE_OFFSET linear mapping, but we're not on the
kernel trap table yet so those addresses won't translate properly.
One idea is to do a by-hand firmware call like we do in the
early bootup code and elsewhere here in trampoline.S But this
fails as well, as aparently the secondary processors are not
booted with OBP's special locked TLB entries loaded. These
are necessary for the firwmare to processes TLB misses correctly
up until the point where we take over the trap table.
This does need to be resolved at some point.
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Ben Dooks
The NWFPE is producing a number of errors from sparse
due to not defining a number of functions in the
header files.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from George G. Davis
Fix leading, trailing and other miscellaneous whitespace issues
in arch/arm/kernel/alignment.c.
Signed-off-by: George G. Davis <gdavis@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from George G. Davis
When building for CPU_V6 targets, we should use -mtune=arm1136j-s rather
than -mtune=strongarm but fall back to the later in case someone is
using an older toolchain (although they should really upgrade instead).
Signed-off-by: George G. Davis <gdavis@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Do not export items that are not needed by symbol name
elsewhere
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The items in the export table do not need to be
exported elsehwere, so quash the sparse warning
by making the symbol for the table entry static.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
arch/arm/mach-s3c2410/time.c is missing include
of cpu.h, causing the declaration of the timer
struct (s3c24xx_timer) to be flagged as missing
the declaration.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Either no one is using an ARM710 with recent kernels, or all ARM710s
still in use are not afflicted by this swi bug. Nevertheless, the code
to work around the ARM710 swi bug is itself currently buggy since it
uses r8 as a pointer to S_PC while in fact it holds the spsr content
these days. Fix that, and simplify the code as well.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Glibc is about to get some new high precision timer stuff that relies on
the standard timebase of the PPC architecture.
However, some (rare & old) CPUs do not have such timebase and it is a
bit annoying to have your stuff just crash because you are running on
the wrong CPU...
This exposes to userland a CPU feature bit that tells that the current
processor doesn't have a standard timebase. It's negative logic so that
glibc will still "just work" on older kernels (it will just be unhappy
on those old CPUs but that doesn't really matter as distro tend to
update glibc & kernel at the same time).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Give an empty definition for clear_can_do_skas() when it is not needed.
Thanks to Junichi Uekawa <dancer@netfort.gr.jp> for reporting the
breakage and providing a fix (I re-fixed it in an IMHO cleaner way).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The patch to use host AIO support that I submitted early after 2.6.13 exposed
some problems in the block driver. I have fixes for these, but am not
comfortable putting them into 2.6.14 at this late date. So, this patch reverts
the use of host AIO.
I will resubmit the original patch, plus fixes to the driver after 2.6.14
in order to get a reasonable amount of testing before they're exposed to
the general public.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We were not doing alignment properly when remapping the kernel image.
What we want is a 4MB aligned physical address to map at KERNBASE.
Mistakedly we were 4MB aligning the virtual address where the kernel
initially sits, that's wrong.
Instead, we should PAGE align the virtual address, then 4MB align the
physical address result the prom gives to us.
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer gcc's are generating this relocation, so the module loader needs to
handle it.
Signed-off-by: Peter Bergner <bergner@vnet.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I've noticed that the calculations for seg_size and nr_segs in
__dma_sync_page_highmem() (arch/ppc/kernel/dma-mapping.c) are wrong. The
incorrect calculations can result in either an oops or a panic when running
fsck depending on the size of the partition.
The problem with the seg_size calculation is that it can result in a
negative number if size is offset > size. The problem with the nr_segs
caculation is returns the wrong number of segments, e.g. it returns 1 when
size is 200 and offset is 4095, when it should return 2 or more.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
pSeries_irq_bus_setup is marked __devinit but references s7a_workaround
which is marked __initdata.
Depending on who got the memory for s7a_workaround (and if the value was
now positive), it was possible for PCI hotplugged devices to have 3
subtracted from their interrupt number. This would happen randomly and
caused me much confusion :)
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Breakage noted by Al Viro.
It breaks non-PCI builds, it's probably better to have a more
direct implementation on sparc32, and which driver actually
needs this is still questionable.
We can resolve this in 2.6.15
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to use long long, not long when RMWing a MSR. I think
it's harmless right now, but still should be better fixed
if AMD adds any bits in the upper 32bit of HWCR.
Bug was introduced with the TLB flush filter fix for i386
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CPU hotplug fills up the possible map to NR_CPUs, but it did that after
setting up per CPU data. This lead to CPU data not getting allocated
for all possible CPUs, which lead to various side effects.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On the boot processor, we need to do the move onto the Linux trap
table a little bit differently else we'll take unhandlable faults in
the firmware address space.
Previously we would do the following:
1) Disable PSTATE_IE in %pstate.
2) Set %tba by hand to sparc64_ttable_tl0
3) Initialize alternate, mmu, and interrupt global
trap registers.
4) Call prom_set_traptable()
That doesn't work very well actually with the way we boot the kernel
VM these days. It worked by luck on many systems because the firmware
accesses for the prom_set_traptable() call happened to be loaded into
the TLB already, something we cannot assume.
So the new scheme is this:
1) Clear PSTATE_IE in %pstate and set %pil to 15
2) Call prom_set_traptable()
3) Initialize alternate, mmu, and interrupt global
trap registers.
and this works quite well. This sequence has been moved into a
callable function in assembler named setup-trap_table(). The idea is
that eventually trampoline.S can use this code as well. That isn't
possible currently due to some complications, but eventually we should
be able to do it.
Thanks to Meelis Roos for the Ultra5 boot failure report.
Signed-off-by: David S. Miller <davem@davemloft.net>
Noticed by Terence Ripperda
Undo wrong change in global_flush_tlb. We need to flush the caches in all
cases, not just when pages were reverted. This was a bogus optimization
added earlier, but it was wrong.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Vincent Sanders
Add a defconfig for the ARM Collie platform
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Vincent Sanders <vince@arm.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Vincent Sanders
Add a defconfig for the ARM Corgi Zarus platform
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Vincent Sanders <vince@arm.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Vincent Sanders
Add a defconfig for the ARM Poodle Zarus platform
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Vincent Sanders <vince@arm.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Vincent Sanders
Add a defconfig for the ARM Spitz Zarus platform
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Vincent Sanders <vince@arm.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes the setup of the alignment of the signal frame, so that all
signal handlers are run with a properly aligned stack frame.
The current code "over-aligns" the stack pointer so that the stack frame
is effectively always mis-aligned by 4 bytes. But what we really want
is that on function entry ((sp + 4) & 15) == 0, which matches what would
happen if the stack were aligned before a "call" instruction.
Signed-off-by: Markus F.X.J. Oberhumer <markus@oberhumer.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
UML/x86_64 doesn't run when built with frame pointers disabled. There
was an implicit frame pointer assumption in the stub segfault handler.
With frame pointers disabled, UML dies on handling its first page fault.
The container-of part of this is from Paolo Giarrusso <blaisorblade@yahoo.it>.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch makes swsusp avoid the possible temporary corruption
of page translation tables during resume on x86-64. This is achieved by
creating a copy of the relevant page tables that will not be modified by
swsusp and can be safely used by it on resume.
The problem is that during resume on x86-64 swsusp may temporarily
corrupt the page tables used for the direct mapping of RAM. If that
happens, a page fault occurs and cannot be handled properly, which leads
to the solid hang of the affected system. This leads to the loss of the
system's state from before suspend and may result in the loss of data or
the corruption of filesystems, so it is a serious issue. Also, it
appears to happen quite often (for me, as often as 50% of the time).
The problem is related to the fact that (at least) one of the PMD
entries used in the direct memory mapping (starting at PAGE_OFFSET)
points to a page table the physical address of which is much greater
than the physical address of the PMD entry itself. Moreover,
unfortunately, the physical address of the page table before suspend
(i.e. the one stored in the suspend image) happens to be different to
the physical address of the corresponding page table used during resume
(i.e. the one that is valid right before swsusp_arch_resume() in
arch/x86_64/kernel/suspend_asm.S is executed). Thus while the image is
restored, the "offending" PMD entry gets overwritten, so it does not
point to the right physical address any more (i.e. there's no page
table at the address pointed to by it, because it points to the address
the page table has been at during suspend). Consequently, if the PMD
entry is used later on, and it _is_ used in the process of copying the
image pages, a page fault occurs, but it cannot be handled in the normal
way and the system hangs.
In principle we can call create_resume_mapping() from
swsusp_arch_resume() (ie. from suspend_asm.S), but then the memory
allocations in create_resume_mapping(), resume_pud_mapping(), and
resume_pmd_mapping() must be made carefully so that we use _only_
NosaveFree pages in them (the other pages are overwritten by the loop in
swsusp_arch_resume()). Additionally, we are in atomic context at that
time, so we cannot use GFP_KERNEL. Moreover, if one of the allocations
fails, we should free all of the allocated pages, so we need to trace
them somehow.
All of this is done in the appended patch, except that the functions
populating the page tables are located in arch/x86_64/kernel/suspend.c
rather than in init.c. It may be done in a more elegan way in the
future, with the help of some swsusp patches that are in the works now.
[AK: move some externs into headers, renamed a function]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix whitespace - I split this off the previous patch for easier review.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
After restoring the existing code, make it work also when included in
kernelspace code (which isn't currently the case, but at least this will prevent
people from "fixing" it as just happened).
Whitespace is fixed in next patch - it cluttered the diff too much.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Commit 44456d37b5, between 2.6.13-rc3 and -rc4,
was a "nice cleanup" which broke something. Revert the offending part.
It broke because:
a) because this part doesn't fall under the description
b) the author didn't know what he was doing here
c) the author didn't try to compile the existing code and see that it worked
perfectly.
d) the author didn't ask us what was happening
e) you didn't either, and somebody there should have learned that UML is a bit
different.
In fact, UML is special in linking to host libc and using its includes.
In particular, since host includes always define both __BIG_ENDIAN and
__LITTLE_ENDIAN, ntohll() macros started thinking to be in a big-endian world;
and on-disk compatibility was broken.
Many thanks go to Nix for reporting the problem and correctly diagnosing an
endianness problem.
Btw, this patch restores the previous code, which worked; but the definitions
would be uncorrect if used in kernelspace files.
Next patch addresses that.
Cc: Nix <nix@esperi.org.uk>, Olaf Hering <olh@suse.de>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For files which need to include glibc headers (i.e. userspace files), we
specified the correct flags only for .o, not for .s/.lst/.i. Fix this.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Too many people were confused by skas0 and tried using "mode=skas0". And after
all, they are right - accept this.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a missing $(Q) to a "ln" invocation.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Richard Purdie
Allow the GPIO pin suspend states to be specified for SCOOP devices.
This is needed for correct operation on the spitz platform.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add a missing include from corgi.c
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add some missing parameters from the scoop calls on collie.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from George G. Davis
Add test for invalid LDRD/STRD Rd cases in ARM alignment handler
and restore SWP printk KERN_ERR.
Signed-off-by: Steve Longerbeam <slongerbeam@mvista.com>
Signed-off-by: George G. Davis <gdavis@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
irq.c is missing the inclusion of asm/io.h, which causes
readb() and writeb() the be undefined.
Signed-off-by: Sven Hartge <hartge@ds9.argh.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- added typedef unsigned int __nocast gfp_t;
- replaced __nocast uses for gfp flags with gfp_t - it gives exactly
the same warnings as far as sparse is concerned, doesn't change
generated code (from gcc point of view we replaced unsigned int with
typedef) and documents what's going on far better.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We need to use stricter memory barriers around the block
load and store instructions we use to save and restore the
FPU register file.
Signed-off-by: David S. Miller <davem@davemloft.net>
I've noticed a kernel hang during a storm of CMC interrupts, which was
tracked down to the continual execution of the interrupt handler.
There's code in the CMC handler that's supposed to disable CMC
interrupts and switch to polling mode when it sees a bunch of CMCs.
Because disabling CMCs across all CPUs isn't safe in interrupt context,
the disable is done with a schedule_work(). But with continual CMC
interrupts, the schedule_work() never gets executed.
The following patch immediately disables CMC interrupts for the current
CPU. This then allows (at least) one CPU to ignore CMC interrupts,
execute the schedule_work() code, and disable CMC interrupts on the rest
of the CPUs.
Acked-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Bryan Sutula <Bryan.Sutula@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
By allocating early memory for the firmware page tables, we
can write over the beginning of the initrd image.
So what we do now is:
1) Read in firmware translations table while still on the
firmware's trap table.
2) Switch to Linux trap table.
3) Init bootmem.
4) Build firmware page tables using __alloc_bootmem().
And this keeps the initrd from being clobbered.
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Catalin Marinas
There is no reason to not allow these config options. They are useful when
the hardware has problems.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove some duplicated items due to the inclusion of the general
drivers/Kconfig file. These are now taken from drivers/char/Kconfig,
and can be turned off there as well (which is desirable sometimes).
Signed-off-by: Martin Habets <errandir_news@mph.eclipse.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Older Macs which uses the VIA chip timers to calibrate the timebase used
some code that wouldn't work if HZ wasn't divisible by 100...
This fixes it at least for 250. Not totally perfect but should be
enough for now (so it at least works with the default value which is now
250).
There is still a potential issue with the core using CLOCK_TICK_RATE to
maintain xtime and CLOCK_TICK_RATE value on ppc32 is pure crap, but that
is a different problem, this patch at least brings us back to our
previous situation.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Drop global bit from early low mappings
Suggested by Linus, originally also proposed by Suresh.
This fixes a race condition with early start of udev, originally
tracked down by Suresh B. Siddha. The problem was that switching
to the user space VM would not clear the global low mappings
for the beginning of memory, which lead to memory corruption.
Drop the global bits.
The kernel mapping stays global because it should stay constant.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Instead of code patching to handle the page size fields in
the context registers, just use variables from which we get
the proper values.
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Nicolas Pitre
If gcc decides to assign lr to %0 we're screwed.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
The cmpxchg emulation syscall needs write access.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Sascha Hauer
Current implementation of imx_gpio_mode does not allow to
configure all alternate routing possibilities of the i.MX. With
this patch every bit in the gpio setup registers has a
corresponding bit in the gpio_mode parameter, so every routing
should be possible now.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
gensparse_defconfig is a config generated file for SPARSEMEM and GENERIC
kernel configuration (defconfig).
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The old code had the IP and SP coming from the registers in the thread
struct, which are completely wrong since those are the userspace
registers. This fixes that by pulling the correct values from the
jmp_buf in which the kernel state of each thread is stored.
Signed-off-by: Allan Graves <allan.graves@oracle.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Al's build tidying missed one bit from me - without this UML doesn't boot.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Acked-by: Al Viro <viro@ftp.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is the minimal set of changes required by ia64 to use SPARSEMEM.
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
For FLATMEM contig_page_data has been made transparent to the arch code.
This patch conforms to that change.
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The patch modifies the Kconfig file to introduce the new memory model
options and other related SPARSEMEM changes. There is also a minor change
in the Makefile.
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
2.6.14-rc2 does not assign cpus to proper nodeids on our em64t numa boxen.
Our boxes use acpi srat for parsing the numa information.
srat_detect_node() used phys_proc_id[] to get to the cpu's local apic id,
but phys_proc_id[] represents the cpu<->initial_apic_id mapping. The
following patch fixes this problem. Now apicid_to_node[] is properly
indexed with the local apic id.
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Catalin Marinas
Data abort caused by ldrex/strex can leave the exclusive monitor in an
unpredictable state. It is recommended that a clrex/strex is performed to
clear this state.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pass in the pointer to the on-stack registers rather than using them
directly as the arguments.
Ivan noticed that I missed a spot when purging the registers as first
stack parameter idiom.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds the new iBook G4 (manufactured after July 2005) to the
PowerMac models table. The model name (PowerBook6,7) is taken from a
12" iBook, I don't know if it also matches the 14" version. The patch
applies to a vanilla 2.6.13.2 kernel.
Signed-off-by: Sven Henkel <shenkel@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Vincent Sanders
When building the fortunet ARM platform it fails to compile because of
missing include.
Signed-off-by: Vincent Sanders <vince@arm.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The incorrect kprobe_mutex usage on x86_64 had percolated to ppc64 too.
First noticed by Yanmin Zhang.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Serial port only needs 32 bytes of resource space but we are currently
asking for 64K.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
[ diff went missing first time due to corrupted patch ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The old 550Mhz titanium powerbook can switch to a lower frequency
(500Mhz). A user has been repeately reporting overtemp conditions on his
machine at high speed so this simple patch adds support to PowerMac
cpufreq for this machine. The difference in frequency isn't big but seem
enough to fix that user's problems. The patch has been around for some
time now and doesn't seem to cause any problem, so I suppose it could go
in now.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Alain RICHARD <alain.richard@equation.fr>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The tests Alok carried out on Petr's box confirmed that cpu_to_node[BP] is
not setup early enough by numa_init_array due to the x86_64 changes in
2.6.14-rc*, and unfortunately set wrongly by the work around code in
numa_init_array(). cpu_to_node[0] gets set with 1 early and later gets set
properly to 0 during identify_cpu() when all cpus are brought up, but
confusing the numa slab in the process.
Here is a quick fix for this. The right fix obviously is to have
cpu_to_node[bsp] setup early for numa_init_array(). The following patch
will fix the problem now, and the code can stay on even when
cpu_to_node{BP] gets fixed early correctly.
Thanks to Petr for access to his box.
Signed off by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Alok N Kataria <alokk@calsoftinc.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the BP node_to_cpumask. 2.6.14-rc* broke the boot cpu bit as the
cpu_to_node(0) is now not setup early enough for numa_init_array.
cpu_to_node[] is setup much later at srat_detect_node on acpi srat based
em64t machines. This seems like a problem on amd machines too, Tested on
em64t though. /sys/devices/system/node/node0/cpumap shows up sanely after
this patch.
Signed off by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The up()/down() orders are incorrect in arch/x86_64/kprobes.c file.
kprobe_mutext is used to protect the free kprobe instruction slot list.
arch_prepare_kprobe applies for a slot from the free list, and
arch_remove_kprobe returns a slot to the free list. The incorrect up()/down()
orders to operate on kprobe_mutex fail to protect the free list. If 2 threads
try to get/return kprobe instruction slot at the same time, the free slot list
might be broken, or a free slot might be applied by 2 threads.
Signed-off-by: Zhang Yanmin <Yanmin.zhang@intel.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Revert commit 12ebcd73e4, i.e. [PATCH] uml: run
mconsole "sysrq" in process context on request from Jeff Dike.
a) sysrq may be run when the scheduler is non-functioning
b) the warning I wanted to fix actually came from the fault handler run in
atomic context. But I fixed that not to take the semaphore in a separate
patch.
c) the fault handler is run because of a fault, and that fault was
unaffected by this patch.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SEGV_MAYBE_FIXABLE tests ptrace_faultinfo, and depends on it being 1 only in
SKAS3 mode, while currently when running with mode=tt it will be 1 anyway.
Fix this, and do the same for proc_mm.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I hadn't been running a SKAS3 host when testing the "uml: fix hang in TT mode
on fault" patch (commit 546fe1cbf9), and I
didn't think enough to the missing trap_no in SKAS3 mode.
In fact, the resulting kernel doesn't work at all in SKAS3 mode.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I need the following patch to compile -git8 here, otherwise these
files fail to compile (asm/hw_irq.h needs definitions from
linux/irq.h and that file provides the required include ordering).
I did not do a full audit, though there looks to be many other
places that should get the same treatment, if this is the right
way to do it.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
BUILD_BUG_ON(1) is asking for trouble (and getting it) when used in that
manner - dead code elimination happens after we parse it and invalid
type is invalid type, dead code or not.
It might be version-dependent, but at least 4.0.1 refuses to accept
that.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Gen FUKATSU
Invalidate BTB entry instruction flushes two instruction
at a time. Therefore this instruction should be done four
times after invalidate instruction cache line.
Signed-off-by: Gen Fukatsu
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
The warning is caused by the gic_set_cpu() function being defined but not
used if CONFIG_SMP is not defined.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
When CONFIG_CPU_CACHE_VIPT is defined, the flush_pfn_alias() function is
implicitely declared and it later conflicts with its actual definition.
This patch moves the function definition to the beginning of the file.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1) Use cpudata cache line sizes, not magic constants.
2) Align start address in cheetah case so we do not get
unaligned address traps. (pgrep was good at triggering
this, via /proc/${pid}/cmdline accesses)
Signed-off-by: David S. Miller <davem@davemloft.net>
Delete all of the code working with sp_banks[] and replace
with clean acquisition and sorting of physical memory
parameters from the firmware.
Signed-off-by: David S. Miller <davem@davemloft.net>
The attempt to fixup the lockless mce log buffer introduced an infinite loop
when trying to find a free entry.
And:
Using rcu_dereference() to load mcelog.next doesn't seem to be sufficient
enough to ensure that mcelog.next is loaded each time around the loop in
mce_log(). Instead, use an explicit rmb() to ensure that the compiler gets it
right.
AK: turned the smp_wmbs into true wmbs to make sure they are not
reordered by the compiler on UP.
Signed-off-by: Mike Waychison <mikew@google.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I checked with AMD and they requested to only disable it for family 15.
Also disable it for i386 too. And some style fixes.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In arch/ppc/boot/ld.script we need OUTPUT_ARCH(powerpc:common) for the
same reasons why we need it in vmlinux.lds.S; when we build on ppc64
box, we need to be explicit about the target.
See http://linus.bkbits.net:8080/linux-2.5/cset@1.1784.8.10 for the
corresponding fix in vmlinux.lds.S.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
UML makefiles sanitized:
- number of generated headers reduced to 2 (from user-offsets.c and
kernel-offsets.c resp.). The rest is made constant and simply
includes those two.
- mk_... helpers are gone now that we don't need to generate these
headers
- arch/um/include2 removed since everything under arch/um/include/sysdep
is constant now and symlink can point straight to source tree.
- dependencies seriously simplified.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's pointless to include mach-types.h if you're not going to use
anything from it. These references were removed as a result of:
grep -lr 'asm/mach-types\.h' . | xargs grep -L 'machine_is_\|MACH_TYPE_\|MACHINE_START\|machine_type'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since asm/hardware.h's only reason for existing is to include
asm/arch/hardware.h, it's completely pointless to include both.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix
arch/arm/mach-pxa/generic.c:242: warning: 'struct i2c_pxa_platform_data' declared inside parameter list
caused by missing asm/arch/i2c.h include.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Instead of doing byte-at-a-time user accesses to figure
out where the fault occurred, read the saved fault_address
from the current thread structure.
For the sake of defensive programming, if the fault_address
does not fall into the user buffer range, simply assume the
whole area faulted. This will cause the fixup for
copy_from_user() to clear the entire kernel side buffer.
Signed-off-by: David S. Miller <davem@davemloft.net>
We were not calling kernel_mna_trap_fault() correctly.
Instead of being fancy, just return 0 vs. -EFAULT from
the assembler stubs, and handle that return value as
appropriate.
Create an "__retl_efault" stub for assembler exception
table entries and use it where possible.
Signed-off-by: David S. Miller <davem@davemloft.net>
The funny "range" exception table entries we had were only
used by the compat layer socketcall assembly, and it wasn't
even needed there.
For free we now get proper exception table sorting and fast
binary searching.
Signed-off-by: David S. Miller <davem@davemloft.net>
/proc/iomem describes a block of memory as "Kernel data",
but the end address is derived from "_edata". The kernel
actually has many other sections beyond _edata. Get the
real end address from _end.
Acked-by: Khalid Aziz <khalid_aziz@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
My previous patch fixing invalidation of huge PTEs wasn't good enough, we
still had an issue if a PTE invalidation batch contained both small and
large pages. This patch fixes this by making sure the batch is flushed if
the page size fed to it changes.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Mikey and I were testing kexec and hit a lockup. It turns out gcc 4.0
optimises the kexec_prepare_cpus loop so we avoid reloading paca.hw_cpu_id.
A gcc barrier() fixes the problem.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This should resolve the issue seen in bugme bug #5105, where it is assumed
that dualcore x86_64 systems have synced TSCs. This is not the case, and
alternate timesources should be used instead.
For more details, see:
http://bugzilla.kernel.org/show_bug.cgi?id=5105
Andi's earlier concerns that the TSCs should be synced on dualcore systems
have been resolved by confirmation from AMD folks that they can be
unsynced.
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I did something stupid in my oprofile fix, here's the obvious fix:
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Also, the us3_cpufreq driver can work on Ultra-IV and IV+.
They use the SAFARI bus register to control the clock divider
just like Ultra-III and III+ do.
Signed-off-by: David S. Miller <davem@davemloft.net>
arm maketools needs include/asm-arm in place in the build tree.
On normal builds it's always there, of course, but on O= it's created
(by generic code) too late - when we get to asm-offset.h.
We used to get away with that by accident - creation of
include/asm-arm/arch symlink creates include/asm-arm and it happened
to go before maketools. However, we did not have such dependency,
so that luck didn't last - now maketools is picked first and we are screwed.
Both the symlink and maketools are prerequisites of the same
target (archprepare). This fix is obvious - make the latter explicitly
depend on the former and be done with that.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We do _not_ need "sparse" in sparse arguments ;-)
What we do need is __BIG_ENDIAN__; right now unconditional, when m32r
starts using CPU_LITTLE_ENDIAN, we'll need to adjust.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Most of these guys are simply not needed (pulled by other stuff
via asm-i386/hardirq.h). One that is not entirely useless is hilarious -
arch/i386/oprofile/nmi_timer_int.c includes linux/irq.h... as a way to
get linux/errno.h
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In order to do it correctly on UltraSPARC-III+ and later we'd
need to add some complicated code to set the TAG access extension
register before loading the TLB.
Since this optimization gives questionable gains, it's best to
just remove it for now instead of adding the fix for Ultra-III+
Signed-off-by: David S. Miller <davem@davemloft.net>
It tries to batch up the tag loads and comparisons, and
then the stores. And this is just complicated instead
of efficient.
Also, make the symbol of the Cheetah version more grepable.
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Vincent Sanders
A recent patch which made IXP4xx mach_desc's depend on config options
had the effect of not building the kernel for several machines it
possibly could be, this patch updates the default config to ensure all
possible machines are built for by default.
Signed-off-by: Vincent Sanders <vince@arm.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
At boot time, determine the D-cache, I-cache and E-cache size and
line-size. Use them in cache flushes when appropriate.
This change was motivated by discovering that the D-cache on
UltraSparc-IIIi and later are 64K not 32K, and the flushes done by the
Cheetah error handlers were assuming a 32K size.
There are still some pieces of code that are hard coding things and
will need to be fixed up at some point.
While we're here, fix the D-cache and I-cache parity error handlers
to run with interrupts disabled, and when the trap occurs at trap
level > 1 log the event via a counter displayed in /proc/cpuinfo.
Signed-off-by: David S. Miller <davem@davemloft.net>
The trick is that we do the kernel linear mapping TLB miss starting
with an instruction sequence like this:
ba,pt %xcc, kvmap_load
xor %g2, %g4, %g5
succeeded by an instruction sequence which performs a full page table
walk starting at swapper_pg_dir.
We first take over the trap table from the firmware. Then, using this
constant PTE generation for the linear mapping area above, we build
the kernel page tables for the linear mapping.
After this is setup, we patch that branch above into a "nop", which
will cause TLB misses to fall through to the full page table walk.
With this, the page unmapping for CONFIG_DEBUG_PAGEALLOC is trivial.
Signed-off-by: David S. Miller <davem@davemloft.net>
We accidentally corrupted the TLS value when clearing out the ARMv6
exclusive monitor. Avoid doing so.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Current kernel has a couple of sneaky bugs in the ppc64 hugetlb code that
cause huge pages to be potentially left stale in the hash table and TLBs
(improperly invalidated), with all the nasty consequences that can have.
One is that we forgot to set the "secondary" bit in the hash PTEs when
hashing a huge page in the secondary bucket (fortunately very rare).
The other one is on non-LPAR machines (like Apple G5s), flush_hash_range()
which is used to flush a batch of PTEs simply did not work for huge pages.
Historically, our huge page code didn't batch, but this was changed without
fixing this routine. This patch fixes both.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a #define for SN_SAL_IOIF_PCI_SAFE and makes that the
preferred method of implementing sn_pci_legacy_read() and
sn_pci_legacy_write().
This SAL call has been present in SGI proms since version 4.10. If the
SN_SAL_IOIF_PCI_SAFE call fails, revert to the previous code for compatability
with older proms.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Address space resources for ACPI devices have a producer/consumer
flag. All devices "consume" the indicated address space. If the
resource is marked as a "producer", the range is also passed on
to child devices.
We currently ignore this flag when setting up MMIO and I/O port
windows for PCI root bridges, so we could mistakenly interpret
a "consumed-only" range, like CSR space for the device itself,
as a window that is routed to children.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Remove io_remap_page_range() from all of Linux 2.6.x (as requested and
suggested by Randy Dunlap) and minor clean-ups.
Signed-off-by: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
User get *a lot* confused when consoles don't work but we don't report
anything. And, as reported in the comment, using printk to report "your
console doesn't work" isn't likely to go that far.
Fix the problem on the base of this: stack consumption by host printf(). Use
kernel sprintf() and os_write_file, using a wild guess that one page will be
enough for the message, to preallocate the buffer with kmalloc().
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
setup_initial_poll is only called with sigio_lock() held, so use appropriate
allocation.
Also, parse_chan() can also be called when holding a spinlock (see line_open()
-> parse_chan_pair()).
I have sporadic problems (spinlock taken twice, with spinlock debugging on UP)
which could be caused by a sequence like "take spinlock, alloc and go to
sleep, take again the spinlock in the other thread".
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
GFP_ATOMIC | GFP_KERNEL is meaningless and won't work. Actually it never
worked, even in 2.4.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Following i386, we should maybe refuse trying to fault in pages when we're
doing atomic operations, because to handle the fault we could need to take
already taken spinlocks.
Also, if we're doing an atomic operation (in the sense of in_atomic()) we're
surely in kernel mode and we're surely going to handle adequately the failed
fault, so it's safe to behave this way.
Currently, on UML SMP is rarely used, and we don't support PREEMPT, so this is
unlikely to create problems right now, but it might in the future.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Things are breaking horribly with sysrq called in interrupt context. I want
to try to fix it, but probably this is simpler. To tell the truth, sysrq is
normally run in interrupt context, so there shouldn't be any problem.
There's also a warning from the fault handler because it's run in atomic
context (I have a patch for that, only I deferred it). This is why I'm doing
this.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Avoid setting w = 0 twice. Spotted this (trivial) thing which is needed for
another patch.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current code doesn't handle well general protection faults on the host -
it thinks that cr2 is always the address of a page fault. While actually, on
general protection faults, that address is not accessible, so we'd better
assume we couldn't satisfy the fault. Currently instead we think we've fixed
it, so we go back, retry the instruction and fault again endlessly.
This leads to the kernel hanging when doing copy_from_user(dest, -1, ...) in
TT mode, since reading *(-1) causes a GFP, and we don't support kernel
preemption.
Thanks to Luo Xin for testing UML with LTP and reporting the failures he got.
Cc: Luo Xin <luothing@sina.com>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Simplify the code by using strlcat() instead of strncat() and manual
appending.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Only remove the UML pidfile and management socket if we created them.
Currently in case two UMLs are started with the same umid, the second will
remove the first's ones.
Probably we should also panic() at that point, not sure however.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The SMU is the "system controller" chip used by Apple recent G5 machines
including the iMac G5. It drives things like fans, i2c busses, real time
clock, etc...
The current kernel contains a very crude driver that doesn't do much more
than reading the real time clock synchronously. This is a completely
rewritten driver that provides interrupt based command queuing, a userland
interface, and an i2c/smbus driver for accessing the devices hanging off
the SMU i2c busses like temperature sensors. This driver is a basic block
for upcoming work on thermal control for those machines, among others.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix my stupid bug in the 64bit version of PTRACE_SET_DEBUGREG.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix build when iommu debug is enabled.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The recent iommu fix broke booting on some POWER4 and POWER5 LPAR boxes.
It looks like we have been calling the non LPAR iommu_dev_setup on LPAR
machines for a while. The recent iommu fix caused that code path to
fail.
It looks like we just need to hook up the devices iommu_table to the
parents one, so do that instead of calling iommu_dev_setup_pSeries and
crossing the streams.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
acquire_console_sem() does BUG() in interrupt context now, as in the case
of SysRq-b.
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Current -git tree doesn't build when enabling oprofile on a non-bookE CPU
(like on a PowerMac for example). While there is no performance counter
support for these CPUs implemented yet, it's still nice to be able to use
the timer based sampling, and that got broken.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Instead of all of this cpu-specific code to remap the kernel
to the correct location, use portable firmware calls to do
this instead.
What we do now is the following in position independant
assembler:
chosen_node = prom_finddevice("/chosen");
prom_mmu_ihandle_cache = prom_getint(chosen_node, "mmu");
vaddr = 4MB_ALIGN(current_text_addr());
prom_translate(vaddr, &paddr_high, &paddr_low, &mode);
prom_boot_mapping_mode = mode;
prom_boot_mapping_phys_high = paddr_high;
prom_boot_mapping_phys_low = paddr_low;
prom_map(-1, 8 * 1024 * 1024, KERNBASE, paddr_low);
and that replaces the massive amount of by-hand TLB probing and
programming we used to do here.
The new code should also handle properly the case where the kernel
is mapped at the correct address already (think: future kexec
support).
Consequently, the bulk of remap_kernel() dies as does the entirety
of arch/sparc64/prom/map.S
We try to share some strings in the PROM library with the ones used
at bootup, and while we're here mark input strings to oplib.h routines
with "const" when appropriate.
There are many more simplifications now possible. For one thing, we
can consolidate the two copies we now have of a lot of cpu setup code
sitting in head.S and trampoline.S.
This is a significant step towards CONFIG_DEBUG_PAGEALLOC support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Verify the pfn is valid before calling pfn_to_page(),
and cut isolation message if nothing was done.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Wire the MCA/INIT handler stacks into DTR[2] and track them in
IA64_KR(CURRENT_STACK). This gives the MCA/INIT handler stacks the
same TLB status as normal kernel stacks. Reload the old CURRENT_STACK
data on return from OS to SAL.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The sd driver now uses scsi_execute_req() for almost everything.
scsi_execute_req() converts requests into scatterlists.
Fix the HP SCSI disk simulator to understand scatterlists for
more commands.
Without this patch the current kernel will not boot on the simulator
(the disks are always detected as having no sectors, and so cannot be
mounted).
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
For platforms that don't have PCI IO at 0 the outbound window
registers were not being properly configured.
Signed-off-by: Andrew Klossner <andrew@cesa.opbu.xerox.com>
Signed-off-by: Kumar K. Gala <kumar.gala@freescale.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Because we don't access the PAGE_OFFSET linear mappings
any longer before we take over the trap table from the
firmware, we don't need to load dummy mappings there
into the TLB and we don't need the bootmap_base hack
any longer either.
While we are here, check for a larger than 8MB kernel
and halt the boot with an error message. We know that
doesn't work, so instead of failing mysteriously we
should let the user know exactly what's wrong.
Signed-off-by: David S. Miller <davem@davemloft.net>
Just allocate them physically starting from the end of
the kernel image. This incredibly simplifies our MM
bootstrap in that we don't need any mappings in the linear
PAGE_OFFSET area working in order to bootstrap ourselves and
take over the trap table from the firmware.
Many further simplifications are possible now, and this also
sets the stage for CONFIG_DEBUG_PAGEALLOC support.
Signed-off-by: David S. Miller <davem@davemloft.net>
This was kind of ugly, and actually buggy. The bug was that
we didn't handle a machine with memory starting > 4GB. If
the 'prompmd' was allocated in physical memory > 4GB we'd
croak because the obp_iaddr_patch and obp_daddr_patch things
only supported a 32-bit physical address.
So fix this by just loading the appropriate values from two
variables in the kernel image, which is locked into the TLB
and thus accesses to them can't cause a recursive TLB miss.
Signed-off-by: David S. Miller <davem@davemloft.net>
The header declaring this function wasn't included, so the function declaration
was totally bogus wrt. the proto - even if this wasn't going to fail at all.
It was so bad that the compile warning I got was "control reaches end of
non-void function", i.e. missing return. Actually, this has been there for ages,
the consolidation patch just added the warning which was needed to clean it up.
Nice. Really.
Cc: Allan Graves <allan.graves@gmail.com>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Explain why the casting we do to silence this warning is indeed safe.
It is because the field we're casting from, though being 64-bit wide, was filled
with a pointer in first place by ourselves.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Readd this header (deleted in 60d339f6fe). A
warning is spit out here about undeclared getpgrp().
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Even if with a bit of misunderstanding, Al fixed this in commit
95608261da.
Well, the symbol was intended to come from userspace (it exists there on normal
host), but since some hosts may miss that, using the kernel one is just as fine.
However, rename it to be named consistently with the rest.
Actually, he missed converting ELFCLASS32 to coming from kernel headers. For
consistence, add ELFCLASS64 too.
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
gcc is now complaining during link on some hosts - fix it as for other things.
Reported by Antoine Martin <antoine@nagafix.co.uk>.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Translate uname output taken from the host if needed.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I am a lamer :-(. Luckily, Luo Xin performed LTP testing and found this failure.
Btw, the fact that the patch in which I introduced this was merged shows that:
a) I'm really trusted by people
b) sometimes they're wrong about point a).
c) lack of time for reviewers.
CC: Luo Xin <luothing@sina.com>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When removing verify_area, verify_area_{tt,skas} were forgotten.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Catalin Marinas
This patch prevents the "noreturn function does return" warning in the
__bug() function in arch/arm/kernel/traps.c
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
zImage.vmode was recently added. It's a version of zImage in which the ELF
note section used by open firmware indicates that it requires a virtual
mode instance of OF instead of real mode. This allows it to work with
Apple OF, and thus is directly bootable (or netbootable) from OF command
line. (Unfortunately, pSeries OF sort-of requires real mode and Apple OF
sort-of requires virtual mode, and both tend to be unhappy if no notes
section specifies the mode at all).
However, we forgot to add zImage.vmode to the default G5 build. This
fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The new version of the flattened device tree passes the boot cpuid in the
header instead of via a linux,boot-cpu property.
We need to update the in kernel OF parsing code to do this, otherwise
machines with a non zero boot cpuid fail to come up.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some RS64 systems (such as F80) have non-python host bridges with EADS.
However, they have two EADS with 4 buses each under them, so the old logic
that assumed no more than 7 busses per PHB failed miserably.
Big thanks to Olaf Hering for helping me test this, he's got one of the few
machines that broke from the previous logic.
Also, to be a bit smarter at detecting the need for a PHB-level IOMMU table
by checking for the presence of an ISA bus. Only PHBs with ISA bridges
should need the PHB-level table.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Anton Blanchard <anton@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
My code to set up the PCI tree from the Open Firmware device tree was
setting IORESOURCE_* flags on the resources for the devices, but not
the PCI_BASE_ADDRESS_* flags. This meant that some drivers
misbehaved, and /proc/pci showed the wrong types for the resources.
This fixes it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Arrange the modules, OBP, and vmalloc areas such that a range
verification can be done quite minimally.
Signed-off-by: David S. Miller <davem@davemloft.net>
As per x86, we may deadlock while trying to get the mmap semaphore.
Implement the same fix, which allows (eg) recursive faults to cause
an oops instead of deadlocking.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
This code is not being exported, declare it static
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The `make buildcheck` is erroneously reporting that the .arch.info
list is referencing items in the .init section as it is not itself
postfixed with .init
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The `make buildcheck` is erroneously reporting that the .proc.info
list is referencing items in the .init section as it is not itself
postfixed with .init
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The `make buildcheck` is erroneously reporting that the earlyparam
list is referencing items in the .init section as it is not itself
postfixed with .init
Also, as per rmk's suggestion, rename the __early_param to
.early_param to bring it into line with everything else
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Vincent Sanders
Shark platform fails to build with gcc 4 because of a bad lvalue assignement
Signed-off-by: Vincent Sanders <vince@arm.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The `make buildcheck` is erroneously reporting that the taglist
is referencing items in the .init section as it is not itself
postfixed with .init
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This showed that arch/sparc64/kernel/ptrace.c was not getting
the define properly, and thus the code protected by this ifdef
was never actually compiled before. So fix that too.
Signed-off-by: David S. Miller <davem@davemloft.net>
Because we use byte loads/stores to cons up the value
in and out of registers, we can't expect the ASI endianness
setting to take care of this for us. So do it by hand.
This case is triggered by drivers/block/aoe/aoecmd.c in the
ataid_complete() function where it goes:
/* word 100: number lba48 sectors */
ssize = le64_to_cpup((__le64 *) &id[100<<1]);
This &id[100<<1] address is 4 byte, rather than 8 byte aligned,
thus triggering the unaligned exception.
Signed-off-by: David S. Miller <davem@davemloft.net>
Move acpi_map_iosapics() from pci.c to acpi.c, since it doesn't
have anything to do with PCI.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Update comment about how ar.k0 is used. Make the initialization the
same as in start_secondary() (no functional change, just make it look
more similar).
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
User mode kexec tools expect to find information about physical
memory in /proc/iomem (as they do on x86) to validate the addresses
that the new kernel will use.
Signed-off-by: Khalid Aziz <khalid.aziz@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Basically, this extends original dp264 fixup to all dp264 variations.
Here is one minor change: mask out bits 4-7 of a value assigned by SRM,
because
- newer consoles report ISA IRQs with offset 0xe0;
- even if console IRQ value is bogus, we'll have a value < 16
so it should be harmless as it won't clash with native IRQs.
Particularly this fixes USB interrupt problem on xp1000 and es40.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Acked-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix:
arch/arm/mach-sa1100/generic.c:224: warning: 'struct mcp_plat_data' declared inside parameter list
caused by mussing structure and function declaration.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Newer binutils complains:
/tmp/cc07pbI9.s:146: Warning: ignoring changed section type for .sched.text
Fix this warning by adding %progbits to the .section.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
Building a kernel for IXDP425 currently includes the machine descriptors
for IXDP465 and PRPMC1100 even if those machines are not configured.
This means we can build a kernel that boots on those machines even
though the machine_is_xxx() macro will always return 0 and other bits
such as PCI won't be compiled in. This can lead to many wasted hours
wondering what you have done to your kernel to make it randomly crash
thus requireing large quantities of beer to be consumed. While I am
all for consumption of large quantities of beer, there are better
reasons to do so then stupid kernel bugs.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
They seem to have been due to AMD errata 63/122; the fix is to disable
TLB flush filtering in SMP configurations.
Confirmed to fix the problem by Andrew Walrond <andrew@walrond.org>
[ Let's see if we'll have a better fix eventually, this is the Q&D
"let's get this fixed and out there" version ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With the new fdtable locking rules, you have to protect fdtable with either
->file_lock or rcu_read_lock/unlock(). There are some places where we
aren't doing either. This patch fixes those places.
Signed-off-by: Dipankar Sarma <dipankar@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Using native cmpxchg offers a slight performance improvement in uml/i386.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Added ppc_sys device and system definitions for PowerQUICC I devices. This
will allow drivers for PQI to be proper platform device drivers. Currently
sys section contains only MPC885 and MPC866. Identification should be done
with identify_ppc_sys_by_name call, with board-specific "name" string
passed, since PQI do not have any register that could identify the SOC.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I forgot to include siginfo.h when I added data breakpoint support. We
must include it in a round-a-bout way in mainline.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix up some pm_message_t types
Signed-Off-By: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
asm/elf.h is bad on x86_64, and i386 doesn't need it any more after Al's
cleanup.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
do_aio used to return -1 on error instead of errno.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The serial UML OS-abstraction layer patch (um/kernel dir).
This joins mem_user.c and mem.c files.
Signed-off-by: Gennady Sharapov <Gennady.V.Sharapov@intel.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The serial UML OS-abstraction layer patch (um/kernel dir).
This moves all system calls from mem_user.c and tempfile.c files under
os-Linux dir.
Signed-off-by: Gennady Sharapov <Gennady.V.Sharapov@intel.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The poster child for this patch is the third tuntap_user hunk. When an ioctl
fails, it properly closes the opened file descriptor and returns. However,
the close resets errno to 0, and the 'return errno' that follows returns 0
rather than the value that ioctl set. This caused the caller to believe that
the device open succeeded and had opened file descriptor 0, which caused no
end of interesting behavior.
The rest of this patch is a pass through the UML sources looking for places
where errno could be reset before being passed back out. A common culprit is
printk, which could call write, being called before errno is returned.
In some cases, where the code ends up being much smaller, I just deleted the
printk.
There was another case where a caller of run_helper looked at errno after a
failure, rather than the return value of run_helper, which was the errno value
that it wanted.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
These ugly double-casts are the result of gdb complaining about size
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
linux/inet.h isn't needed, and on my system, is empty.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This removes a file which is no longer used.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch implements a stack trace for a thread, not unlike sysrq-t does.
The advantage to this is that a break point can be placed on showreqs, so that
upon showing the stack, you jump immediately into the debugger. While sysrq-t
does the same thing, sysrq-t shows *all* threads stacks. It also doesn't work
right now. In the future, I thought it might be acceptable to make this show
all pids stacks, but perhaps leaving well enough alone and just using sysrq-t
would be okay. For now, upon receiving the stack command, UML switches
context to that thread, dumps its registers, and then switches context back to
the original thread. Since UML compacts all threads into one of 4 host
threads, this sort of mechanism could be expanded in the future to include
other debugging helpers that sysrq does not cover.
Note by jdike - The main benefit to this is that it brings an arbitrary thread
back into context, where it can be examined by gdb. The fact that it dumps it
stack is secondary. This provides the capability to examine a sleeping
thread, which has existed in tt mode, but not in skas mode until now.
Also, the other threads, that sysrq doesn't cover, can be gdb-ed directly
anyway.
Signed-off-by: Allan Graves<allan.graves@gmail.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch moves code that is in both switch_to_tt and switch_to_skas to the
top level _switch_to function, keeping us from duplicating code. It is
required for the stack trace patch to work properly.
Signed-off-by: Allan Graves <allan.graves@gmail.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When an asynchronous interruption occurs during the execution of the
'critical section' within the generic interruption handling code (entry.S),
a faulty check for a userspace PSW may result in a corrupted kernel stack
pointer which subsequently triggers a stack overflow check.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add code to support the re-IPL method using diagnose 0x308.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Disable preemption in show_cpuinfo to avoid problems and the warning about
smp_processor_id.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch increases the maximum number of cpus supported on IA64
to 1024. No changes are made to the default SSI size. The patch
simply allows specifying up to 1024p.
There are certainly scaling (& other) issues that also need to be
addressed!!! Additional patches will follow.....
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
There were some trailing white spaces, long lines, brackets in
weird style etc. This patch cleans them up.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch removes some compilation warnings, mostly
trivially. acpi.c fix also noted by Kenji Kaneshige.
Signed-off-by; Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Linus Torvalds