Commit Graph

412 Commits

Author SHA1 Message Date
Russell King 132b16325f ARM: AT91: update clock source registration
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants.  Switch over to using this new interface.

Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-12-19 15:44:53 +00:00
Christian Glindkamp c20b4dd318 at91: Refactor Stamp9G20 and PControl G20 board file
As PControl G20 is a carrier board for the Stamp9G20 SoM, some code can
be shared. Therefore board-stamp9g20.c is refactored to allow reusing the
SoM initialization and board-pcontrol-g20.c is modified to use it.

Signed-off-by: Christian Glindkamp <christian.glindkamp@taskit.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2010-12-17 12:10:39 +01:00
Ryan Mallon 8251544f9e at91: Fix uhpck clock rate in upll case
The uhpck clock should be divided from the utmi clock, not its parent
(main). This change is mostly cosmetic as the uhpck rate value is not
used anywhere except for the debugfs clock output.

Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2010-12-17 12:10:39 +01:00
Jean-Christophe PLAGNIOL-VILLARD 3b24f0950b at91/board-yl-9200: fix typo in video support
for the epson frambuffer support it's CONFIG_FB_S1D13XXX
not CONFIG_FB_S1D135XX

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2010-11-30 17:23:41 +01:00
Jean-Christophe PLAGNIOL-VILLARD 82d5b5c8da at91/picotux200: remove commenting usb device and dataflash support
as based on http://www.picotux.com/pt200/picotux200.pdf
these board does not have such I/O

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2010-11-30 17:23:02 +01:00
Jean-Christophe PLAGNIOL-VILLARD 985f554d8f at91: rename rm9200ek and rm9200dk board file name
to be a few more concistant with the other boards

as ek is for evaluation kit and dk for development kit

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
2010-11-30 17:22:20 +01:00
Jean-Christophe PLAGNIOL-VILLARD 55d83b0a6e at91rm9200ek: fix warning: 'ek_mmc_data' defined but not used
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
2010-11-30 17:22:07 +01:00
Jean-Christophe PLAGNIOL-VILLARD 8e79d2d4e7 at91rm9200dk: fix warning: 'dk_mmc_data' defined but not used
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
2010-11-30 17:21:55 +01:00
Jean-Christophe PLAGNIOL-VILLARD 8ae8cd978b at91: Convert remaining boards to new-style UART initialization
Convert the following AT91RM9200-based boards to the new-style UART
initialization:
  - Ajeco 1ARM Single Board Computer
  - Sperry-Sun KAFA board
  - picotux 200

Remove the deprecated at91_init_serial

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
2010-11-30 17:21:29 +01:00
Lionel Debroux 2f55ac072f suspend: constify platform_suspend_ops
While at it, fix two checkpatch errors.
Several non-const struct instances constified by this patch were added after
the introduction of platform_suspend_ops in checkpatch.pl's list of "should
be const" structs (79404849e9).

Patch against mainline.
Inspired by hunks of the grsecurity patch, updated for newer kernels.

Signed-off-by: Lionel Debroux <lionel_debroux@yahoo.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-11-16 14:14:02 +01:00
Uwe Kleine-König b595076a18 tree-wide: fix comment/printk typos
"gadget", "through", "command", "maintain", "maintain", "controller", "address",
"between", "initiali[zs]e", "instead", "function", "select", "already",
"equal", "access", "management", "hierarchy", "registration", "interest",
"relative", "memory", "offset", "already",

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-11-01 15:38:34 -04:00
Nicolas Ferre 75305d768d at91/atmel-mci: inclusion of sd/mmc driver in at91sam9g45 chip and board
This adds the support of atmel-mci sd/mmc driver in at91sam9g45 devices and
board files. This also configures the DMA controller slave interface for
at_hdmac dmaengine driver.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2010-10-26 11:32:49 +02:00
Nicolas Ferre a2a571b74a AT91: pm: make sure that r0 is 0 when dealing with cache operations
When using CP15 cache operations (c7), we make sure that Rd (r0)
is actually 0 as ARM 926 TRM is saying.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2010-10-26 11:32:48 +02:00
Nicolas Ferre 8aeeda822f AT91: pm: use plain cpu_do_idle() for "wait for interrupt"
For power management at91_pm_enter() routine, use the cpu_do_idle() for a
rock solid "wait for interrupt" implementation.
For AT91SAM9 ARM 926 based chips, we can exceed the cache line length as
we can access RAM even while in self-refresh mode.
We keep plain access to CP15 for at91rm9200 as this feature is not
available: instructions have to be in a single cache line.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2010-10-26 11:32:48 +02:00
Nicolas Ferre bb413db591 AT91: reset: extend alternate reset procedure to several chips
Several at91sam9 chips need the alternate reset procedure to be sure to halt
SDRAM smoothly before resetting the chip.
This is an extension of previous patch "Fix AT91SAM9G20 reset" to all chips
affected.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2010-10-26 11:32:48 +02:00
Nicolas Ferre 1345562b44 AT91: reset routine cleanup, remove not needed icache flush
Generalize assembler reset routine to allow use on several at91sam9 chips.
This patch replace double definitions of SDRAM controller registers and RSTC
registers with use of classical header files.

For this rework, we remove the not needed icache flush as it is already
done in the calling function: arm_machine_restart().

Rename at91sam9g20_reset.S to generalize to several chips.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2010-10-26 11:32:48 +02:00
Nicolas Ferre ef4d63e6f5 AT91: trivial: align comment of at91sam9g20_reset with one more tab
Preparing next patch with longer names

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2010-10-26 11:32:47 +02:00
Peter Horton 184c82e853 AT91: Fix AT91SAM9G20 reset as per the errata in the data sheet
If the SDRAM is not cleanly shutdown before reset it can be left driving
the bus, which then stops the bootloader booting from NAND.

Signed-off-by: Peter Horton <phorton@bitbox.co.uk>
[nicolas.ferre@atmel.com: change file header line order]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2010-10-26 11:32:47 +02:00
Peter Gsellmann abf0c1bc94 AT91: add board support for Pcontrol_G20
Board is a carrier board for Stamp9G20, with additional peripherals
for a building automation system

Signed-off-by: Peter Gsellmann <pgsellmann@portner-elektronik.at>
[nicolas.ferre@atmel.com: remove machine_desc.io_pg_offst and .phys_io]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2010-10-26 11:32:47 +02:00
Linus Torvalds 229aebb873 Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
  Update broken web addresses in arch directory.
  Update broken web addresses in the kernel.
  Revert "drivers/usb: Remove unnecessary return's from void functions" for musb gadget
  Revert "Fix typo: configuation => configuration" partially
  ida: document IDA_BITMAP_LONGS calculation
  ext2: fix a typo on comment in ext2/inode.c
  drivers/scsi: Remove unnecessary casts of private_data
  drivers/s390: Remove unnecessary casts of private_data
  net/sunrpc/rpc_pipe.c: Remove unnecessary casts of private_data
  drivers/infiniband: Remove unnecessary casts of private_data
  drivers/gpu/drm: Remove unnecessary casts of private_data
  kernel/pm_qos_params.c: Remove unnecessary casts of private_data
  fs/ecryptfs: Remove unnecessary casts of private_data
  fs/seq_file.c: Remove unnecessary casts of private_data
  arm: uengine.c: remove C99 comments
  arm: scoop.c: remove C99 comments
  Fix typo configue => configure in comments
  Fix typo: configuation => configuration
  Fix typo interrest[ing|ed] => interest[ing|ed]
  Fix various typos of valid in comments
  ...

Fix up trivial conflicts in:
	drivers/char/ipmi/ipmi_si_intf.c
	drivers/usb/gadget/rndis.c
	net/irda/irnet/irnet_ppp.c
2010-10-24 13:41:39 -07:00
Nicolas Pitre 6451d7783b arm: remove machine_desc.io_pg_offst and .phys_io
Since we're now using addruart to establish the debug mapping, we can
remove the io_pg_offst and phys_io members of struct machine_desc.

The various declarations were removed using the following script:

  grep -rl MACHINE_START arch/arm | xargs \
  sed -i '/MACHINE_START/,/MACHINE_END/ { /\.\(phys_io\|io_pg_offst\)/d }'

[ Initial patch was from Jeremy Kerr, example script from Russell King ]

Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Eric Miao <eric.miao at canonical.com>
2010-10-20 00:27:46 -04:00
Jeremy Kerr 0ea1293009 arm: return both physical and virtual addresses from addruart
Rather than checking the MMU status in every instance of addruart, do it
once in kernel/debug.S, and change the existing addruart macros to
return both physical and virtual addresses. The main debug code can then
select the appropriate address to use.

This will also allow us to retreive the address of a uart for the MMU
state that we're not current in.

Updated with fixes for OMAP from Jason Wang <jason77.wang@gmail.com>
and Tony Lindgren <tony@atomide.com>, and fix for versatile express from
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>.

Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-10-20 00:27:33 -04:00
Russell King 809b4e00ba Merge branch 'devel-stable' into devel 2010-10-19 22:06:36 +01:00
Russell King f779b7dd32 Merge branch 'for-rmk' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into devel-stable
Conflicts:
	arch/arm/mach-at91/include/mach/system.h
	arch/arm/mach-imx/mach-cpuimx27.c

AT91 conflict resolution:
Acked-by: Anders Larsen <al@alarsen.net>
IMX conflict resolution confirmed by Uwe Kleine-König.
2010-10-19 20:12:24 +01:00
Russell King 23beab76b4 Merge branches 'at91', 'dcache', 'ftrace', 'hwbpt', 'misc', 'mmci', 's3c', 'st-ux' and 'unwind' into devel 2010-10-18 22:34:25 +01:00
Justin P. Mattock 50a23e6eec Update broken web addresses in arch directory.
The patch below updates broken web addresses in the arch directory.

Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-10-18 11:03:21 +02:00
Anders Larsen 5c189208b6 ARM: 6436/1: AT91: Fix power-saving in idle-mode on 926T processors
According to Atmel, their 926T processors (AT91 post RM9200) requires
'Wait for Interrupt' mode be entered right after disabling the processor clock
in order to minimise current consumption when idle, so do both provided we're
not running on a 920T (an RM9200).

Furthermore, get rid of the #ifndef CONFIG_DEBUG_KERNEL, since arch_idle()
can be turned off completely with the kernel parameter 'nohlt'.

Cc: Andrew Victor <avictor.za@gmail.com>
Signed-off-by: Anders Larsen <al@alarsen.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-10-08 10:00:36 +01:00
Jean-Christophe PLAGNIOL-VILLARD ee621dd619 net: atmel_macb Kconfig: remove long dependency line
Many Atmel SOC are embedding a MACB controller. This patch removes the long
dependency line for this Atmel MACB ethernet driver configuration entry.
The HAVE_NET_MACB configuration option is located in the net Kconfig file
as it may be setup by ARM/AT91 and AVR32 chips.

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: David Miller <davem@davemloft.net>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
2010-10-07 19:56:55 +02:00
Greg Ungerer cb809b1a5e AT91: fix use of clock disable on idle for AT91x40 devices
The simpler AT91x40 processors do not have the same power management
controller as the new AT91 devices. They do have a simpler power
controller module that we can use to disable the CPU clock at idle
time. Add code to support that.

Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2010-10-07 19:56:54 +02:00
Jean-Christophe PLAGNIOL-VILLARD a6e016f19d AT91: at91sam9g20ek: merge 2mmc version in one board
The board-sam9g20ek-2slot-mmc.c was a revision of the at91sam9g20ek
since board revision C. It contains 2 sd/mmc slots.

This merge keep the support of the old machine ID
MACH_AT91SAM9G20EK_2MMC for backward compatibility.

Now we use the ATAG to pass the hardware functionality to kernel
with this board revision encoding
 bit 0:
     0 => 1 sd/mmc slot
     1 => 2 sd/mmc slots connectors (board from revision C)

system_rev tested on Barebox commit d8f3ee103a9f4bd

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2010-10-07 19:56:31 +02:00
Nicolas Ferre 9a400da84f AT91: Correct configuration define value
The MTD nand driver for Atmel chips is atmel_nand and not at91_nand anymore.
Change wrong configuration variables that were remaining.

Reported-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2010-10-07 19:56:30 +02:00
Jean-Christophe PLAGNIOL-VILLARD 67dd8995fd AT91: at91sam9m10g45ek: use the right machine id
Today the board use 2 machines id AT91SAM9G45EKES and AT91SAM9M10G45EK
now will use only AT91SAM9M10G45EK.

The other boards revision will be specified via system_rev.

for 9g45ekes, m10g45ekes and m10g45ek boards and revisions

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2010-10-07 19:55:55 +02:00
Maxim Osipov 8ed9059533 ARM: 6393/1: AT91: Add flexibity board support
This patch adds support for Flexibity Connect platform from
http://www.flexibity.com/ (AT91SAM9260 based).

Signed-off-by: Maxim Osipov <maxim.osipov@gmail.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-10-04 20:41:37 +01:00
Peter Korsgaard 1d5b4c0fa9 ARM: 6406/1: at91sam9g45: fix i2c bus speed
Use a correct udelay value to get bus speed around 100KHz. The udelay
value was most likely copied from the older devices, but the 9g45
is signicantly faster (400MHz, DDR, ..), so a udelay of 2 gives a
bus speed of around 190KHz, which is too fast for some devices.
A udelay value of 5 gives a bus speed of around 90KHz here.

Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-09-23 15:08:48 +01:00
Nicolas Ferre 4deb22a600 AT91: at91sam9261ek: remove C99 comments but keep information
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2010-09-10 14:36:06 +02:00
Nicolas Ferre 64d72bbeeb AT91: at91sam9261ek board: remove warnings related to use of SPI or SD/MMC
The sd/mmc data structure is not used if SPI is selected. The configuration
of PIO on the board prevent from using both interfaces at the same time
(board dependent).
Remove the warnings at compilation time adding a preprocessor condition.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2010-09-10 12:00:56 +02:00
Nicolas Ferre 1879c45cce AT91: dm9000 initialization update
Add information in dm9000 mac/phy chip initialization:
- irq resource details
- platform data details

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2010-09-10 11:39:23 +02:00
Fabian Godehardt ab64511cbb AT91: SAM9G45 - add a separate clock entry for every single TC block
Without this patch you will not be able to register the first block
because of the second association call on at91_add_device_tc().

Signed-off-by: Fabian Godehardt <fg@emlix.com>
[nicolas.ferre@atmel.com: change tcb1_clk to fake child clock of tcb0_clk]
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2010-09-09 20:14:43 +02:00
Nicolas Ferre 5afddee415 AT91: clock: peripheral clocks can have other parent than mck
While registering clock allow to set parent clock other
than mck. It is useful for clocks than can be seen as
child clock of a peripheral.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
2010-09-09 20:13:23 +02:00
Nicolas Ferre 8d2602e077 AT91: change dma resource index
Reported-by: Dan Liang <dan.liang@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2010-09-07 18:53:33 +02:00
Uwe Kleine-König 5f6878b0d2 ARM: 6323/1: cam60: don't use __init for cam60_spi_{flash_platform_data,partitions}
From: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 12/19] ARM: cam60: don't use __init for cam60_spi_{flash_platform_data,partitions}
Date: Thu,  5 Aug 2010 16:08:46 +0200
Message-Id: <1281017333-5563-12-git-send-email-u.kleine-koenig@pengutronix.de>

These two structs are referenced by cam60_spi_devices.  The latter is
copied at init time to kmalloced memory and so the copy isn't freed after
booting.  So it must not contain references to .init memory.

This isn't noticed by modpost as cam60_spi_devices is in .init.data, too.

Noticed-and-Acked-by: Andrew Victor <linux@maxim.org.za>

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-08-10 22:46:56 +01:00
Uwe Kleine-König 8436b41080 ARM: 6324/1: cam60: move cam60_spi_devices to .init.data
cam60_spi_devices is passed to at91_add_device_spi which calls
spi_register_board_info.  The latter makes a copy of it, so living in
.init.data is OK.

This fixes the following warning in cam60_defconfig:
	WARNING: vmlinux.o(.data+0x2a00): Section mismatch in reference from the variable cam60_spi_devices to the (unknown reference) .init.data:(unknown)
	The variable cam60_spi_devices references
	the (unknown reference) __initdata (unknown)
	If the reference is valid then annotate the
	variable with __init* or __refdata (see linux/init.h) or name the variable:
	*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,

Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-08-10 22:46:42 +01:00
Ryan Mallon 4037242c4f ARM: 6209/3: at91_udc: Add vbus polarity and polling mode
Allow the vbus signal to optionally use polling. This is required if
the vbus signal is connected to an non-interrupting io expander for
example. If vbus is in polling mode, then it is assumed that the vbus
gpio may sleep. Also add an option to have vbus be an active low
signal. Both options are set in the platform data for the device.

Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-07-18 20:39:10 +01:00
Ryan Mallon 064baaca87 ARM: 6209/2: at91: Add support for Bluewater Systems Snapper 9260/9G20 modules
Add support for Bluewater Systems Snapper 9260/9G20 modules

Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-07-09 12:31:52 +01:00
Ryan Mallon 708ee98c5b ARM: 6200/1: AT91: Define NR_BUILTIN_GPIO
Add definition for NR_BUILTIN_GPIO for AT91 family

Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-07-09 12:31:51 +01:00
Nicolas Ferre 7dca3343fc ARM: 6185/1: AT91: PM: dual ram controller support
This rework allows to address tow memory controllers. AT91SAM9263 and
AT91SAM9G45 family have tow SDRAM or DDR/SDRAM controllers. Power management
should take care of this.
This patch modify the way RAM IP header files are implemented to allow
access to registers of both controllers ; it also adds some macros.

We also modify the power management files to use those modified header files.
Slow clock (assembly) and regular power management functions are synchronized
for setting of RAM self-refresh procedure:
(lpr & ~AT91_DDRSDRC_LPCB) | AT91_DDRSDRC_LPCB_SELF_REFRESH

Note that AT91RM9200 is not impacted by this modification.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-07-09 12:31:50 +01:00
Nicolas Ferre 5f9f0a412f ARM: 6169/1: AT91: add new at91 chips in at91sam9g45 family
This is the basic support for at91sam9g46, at91sam9m10 and at91sam9m11. Those
are just very basic cpu macros and clock definition.

Signed-off-by: Patrice Vilchez <patrice.vilchez@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-06-16 23:00:02 +01:00
Dmitry Eremin-Solenikov 8a5c9e3937 ARM: 6163/1: at91sam9g20ek: add fixed-value regulator for wm8731
If CONFIG_REGULATOR is enabled, wm8731 fails on AT91SAM9G20EK board,
since codec driver requires several voltage supplies and none are
provided currently. As requires voltages are hardwired to 3V3, use fixed
voltage regulator for this chip.

Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-06-16 23:00:01 +01:00
Dmitry Eremin-Solenikov 5e886f68e5 ARM: 6162/1: at91sam9g20ek: add fixed-value regulator for wm8731
If CONFIG_REGULATOR is enabled, wm8731 fails on AT91SAM9G20EK board,
since codec driver requires several voltage supplies and none are
provided currently. As requires voltages are hardwired to 3V3, use fixed
voltage regulator for this chip.

Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-06-16 23:00:01 +01:00
Andrea Gelmini becba8a358 ARM: mach-at91: duplicated include
arch/arm/mach-at91/board-sam9m10g45ek.c: mach/hardware.h is included more than once

Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-05-24 20:40:13 +01:00
Russell King 717e7c2672 ARM: remove 'select GENERIC_TIME'
GENERIC_TIME is now enabled by default, so 'select GENERIC_TIME'
is redundant.  Remove them.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-05-18 08:17:56 +01:00
Russell King ac1d426e82 Merge branch 'devel-stable' into devel
Conflicts:
	arch/arm/Kconfig
	arch/arm/include/asm/system.h
	arch/arm/mm/Kconfig
2010-05-17 17:24:04 +01:00
Russell King c39e52a793 Merge branches 'at91', 'bcmring', 'ep93xx', 'iop', 'misc', 'nomadik', 'omap', 'pxa', 'spear' and 'versatile' into devel
Conflicts:
	arch/arm/Makefile
	arch/arm/common/Makefile
	arch/arm/mm/Kconfig
2010-05-17 11:53:39 +01:00
Claudio Scordino e8faff7330 ARM: 6092/1: atmel_serial: support for RS485 communications
Final version of the patch that adds support for RS485 communications to the atmel_serial driver.

The patch has been already sent and discussed on both linux-kernel and linux-arm-kernel mailing lists several times.

Many people collaborated to improve and test the code:

Tested-by: Sebastian Heutling <Sebastian.Heutling@who-ing.de>
Tested-by: Bernhard Roth <br@pwrnet.de>
Reviewed-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Signed-off-by: Michael Trimarchi <michael@evidence.eu.com>
Signed-off-by: Rick Bronson <rick@efn.org>
Signed-off-by: Sebastian Heutling <Sebastian.Heutling@who-ing.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-05-04 16:59:11 +01:00
Anders Larsen aec9562f3d ARM: 6053/1: AT91: Save power by disabling the processor clock when CPU is idle
Disable the processor clock when the CPU is idle.

This saves much more power than merely entering 'Wait for Interrupt' mode.
Since JTAG-debugging doesn't work when the processor clock is switched off,
make it conditional on CONFIG_DEBUG_KERNEL.

Signed-off-by: Anders Larsen <al@alarsen.net>
Acked-by: Andrew Victor <avictor.za@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-05-02 23:13:13 +01:00
Nicolas Ferre e2941054ed ARM: 6056/1: AT91: at91sam9g10 chip identification changed
A bit in the at91sam9g10 identification number changed between Engineering
Sample and final product. This patch will identify both as being at91sam9g10.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-04-14 16:56:27 +01:00
Christian Glindkamp 9b404b7cc3 ARM: 6054/1: AT91: taskit PortuxG20 and Stamp9G20 board support
Both boards share the same board file, as the PortuxG20 is basically an
SBC based on the Stamp9G20.

Signed-off-by: Christian Glindkamp <christian.glindkamp@taskit.de>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-04-14 11:24:53 +01:00
Ernst Schwab b1cdbb5f83 ARM: 5974/1: arm/mach-at91 Makefile: remove two blanks.
Cosmetic change to mach-at91 Makefile: remove two blanks introduced
by earlier patches.

Signed-off-by: Ernst Schwab <eschwab@online.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-04-14 11:22:44 +01:00
Anders Larsen 317aa408d6 ARM: 5975/1: AT91 slow-clock suspend: don't wait when turning PLLs off
From: Julien Langer <julien.langer@gmail.com>

AT91: when turning off the PLLs during suspend, don't wait for the lock
flag to be set. Previously the code would always run into the loop
limitation of 1000 iterations because the flag is never set when turning
the PLLs off.

Comments from Anders Larsen:

 (in http://marc.info/?l=linux-kernel&m=127058929724193&w=2)

Signed-off-by: Julien Langer <julien.langer@gmail.com>
Signed-off-by: Anders Larsen <al@alarsen.net>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-04-14 11:08:43 +01:00
Anders Larsen 9823f1a846 ARM: 6043/1: AT91 slow-clock resume: Don't wait for a disabled PLL to lock
at91 slow-clock resume: Don't wait for a disabled PLL to lock.

We run into this problem with the PLLB on the at91: ohci-at91 disables
the PLLB when going to suspend. The slowclock code however tries to do
the same: It saves the PLLB register value and when restoring the value
during resume, it waits for the PLLB to lock again. However the PLL will
never lock and the loop would run into its timeout because the slowclock
code just stored and restored an empty register.
This fixes the problem by only restoring PLLA/PLLB when they were enabled
at suspend time.

Cc: Andrew Victor <avictor.za@gmail.com>
Signed-off-by: Anders Larsen <al@alarsen.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-04-09 08:31:04 +01:00
John Stultz 5cfc8ee0bb ARM: convert arm to arch_gettimeoffset()
Convert arm to use GENERIC_TIME via the arch_getoffset() infrastructure,
reducing the amount of arch specific code we need to maintain.

The arm architecture is the last arch that need to be converted.

Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
2010-03-24 08:08:58 +00:00
Rob Alley 438ff39d78 ARM: 5986/1: at91sam9g20-ek: Correct braces in I2C registration code
The change introduced in patch 5596/1 used incorrect bracing which
resulted in the AT24 EEPROM no longer being registered.  This patch
corrects the bracing and allows both the WM8731 audio device and AT24
EEPROM device to be registered.

Signed-off-by: Rob Alley <rob.alley@navmanwireless.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-03-13 10:48:21 +00:00
Linus Torvalds c32da02342 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (56 commits)
  doc: fix typo in comment explaining rb_tree usage
  Remove fs/ntfs/ChangeLog
  doc: fix console doc typo
  doc: cpuset: Update the cpuset flag file
  Fix of spelling in arch/sparc/kernel/leon_kernel.c no longer needed
  Remove drivers/parport/ChangeLog
  Remove drivers/char/ChangeLog
  doc: typo - Table 1-2 should refer to "status", not "statm"
  tree-wide: fix typos "ass?o[sc]iac?te" -> "associate" in comments
  No need to patch AMD-provided drivers/gpu/drm/radeon/atombios.h
  devres/irq: Fix devm_irq_match comment
  Remove reference to kthread_create_on_cpu
  tree-wide: Assorted spelling fixes
  tree-wide: fix 'lenght' typo in comments and code
  drm/kms: fix spelling in error message
  doc: capitalization and other minor fixes in pnp doc
  devres: typo fix s/dev/devm/
  Remove redundant trailing semicolons from macros
  fix typo "definetly" -> "definitely" in comment
  tree-wide: s/widht/width/g typo in comments
  ...

Fix trivial conflict in Documentation/laptops/00-INDEX
2010-03-12 16:04:50 -08:00
Russell King 988addf82e Merge branch 'origin' into devel-stable
Conflicts:
	arch/arm/mach-mx2/devices.c
	arch/arm/mach-mx2/devices.h
	sound/soc/pxa/pxa-ssp.c
2010-03-08 20:21:04 +00:00
Jiri Kosina 318ae2edc3 Merge branch 'for-next' into for-linus
Conflicts:
	Documentation/filesystems/proc.txt
	arch/arm/mach-u300/include/mach/debug-macro.S
	drivers/net/qlge/qlge_ethtool.c
	drivers/net/qlge/qlge_main.c
	drivers/net/typhoon.c
2010-03-08 16:55:37 +01:00
Russell King 186f93ea1f Merge branch 'tmpreg' into devel
Conflicts:
	arch/arm/Kconfig
	arch/arm/mach-ux500/include/mach/debug-macro.S
2010-02-25 22:07:25 +00:00
Tony Lindgren 4e6d488af3 ARM: 5910/1: ARM: Add tmp register for addruart and loadsp
Otherwise more complicated uart configuration won't be possible.
We can use r1 for tmp register for both head.S and debug.S.

NOTE: This patch depends on another patch to add the the tmp register
into all debug-macro.S files. That can be done with:

$ sed -i -e "s/addruart,rx|addruart, rx/addruart, rx, tmp/"
	arch/arm/*/include/*/debug-macro.S

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-02-12 17:27:52 +00:00
Daniel Mack 1537a3638c tree-wide: fix 'lenght' typo in comments and code
Some misspelled occurences of 'octet' and some comments were also fixed
as I was on it.

Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Jiri Kosina <trivial@kernel.org>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-02-05 12:22:45 +01:00
Uwe Kleine-König 501d70383a arm/at91: Don't disable irqs in set_next_event and set_mode callbacks
on AT91 the timer irq is shared, so the handler might be entered without
irqs being disabled.  Though this should not happen as the timer irq is
registered early, there have been some reports on the mailing list.

To make debugging that problem easier next time it pops up a
WARN_ON_ONCE is added to the handler if irqs are not off.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
2010-01-22 17:04:39 +01:00
Andrew Victor c9a8fdd8b3 ARM: 5851/1: [AT91] AT572D940HF-EK board support
Add support for the Atmel AT572D940HF-EK board (development board for
the AT572D940HF processor).

Signed-off-by: Antonio R. Costa <costa.antonior@gmail.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-01-20 12:36:27 +00:00
Andrew Victor 5e38efae96 ARM: 5850/1: [AT91] AT572D940HF processor support
Add support for the Atmel AT572D940HF processor (DIOPSIS range).
This processor integrates an ARM926 core, a DSP and the SoC
peripherals usually found on an AT91 processor (USART, SSC, SPI, TWI,
CAN, etc)

Signed-off-by: Antonio R. Costa <costa.antonior@gmail.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-01-20 12:34:06 +00:00
Nicolas Ferre 2635d1ba71 atmel-mci: change use of dma slave interface
Allow the use of another DMA controller driver in atmel-mci sd/mmc driver.
 This adds a generic dma_slave pointer to the mci platform structure where
we can store DMA controller information.  In atmel-mci we use information
provided by this structure to initialize the driver (with new helper
functions that are architecture dependant).

This also adds at32/avr32 chip modifications to cope with this new access
method.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-12-15 08:53:35 -08:00
Linus Torvalds fa395aaec8 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (51 commits)
  Input: appletouch - give up maintainership
  Input: dm355evm_kbd - switch to using sparse keymap library
  Input: wistron_btns - switch to using sparse keymap library
  Input: add generic support for sparse keymaps
  Input: fix memory leak in force feedback core
  Input: wistron - remove identification strings from DMI table
  Input: psmouse - remove identification strings from DMI tables
  Input: atkbd - remove identification strings from DMI table
  Input: i8042 - remove identification strings from DMI tables
  DMI: allow omitting ident strings in DMI tables
  Input: psmouse - do not carry DMI data around
  Input: matrix-keypad - switch to using dev_pm_ops
  Input: keyboard - fix lack of locking when traversing handler->h_list
  Input: gpio_keys - scan gpio state at probe and resume time
  Input: keyboard - add locking around event handling
  Input: usbtouchscreen - add support for ET&T TC5UH touchscreen controller
  Input: xpad - add two new Xbox 360 devices
  Input: polled device - do not start polling if interval is zero
  Input: polled device - schedule first poll immediately
  Input: add S3C24XX touchscreen driver
  ...
2009-12-09 19:52:01 -08:00
Russell King 0719dc3413 Merge branch 'devel-stable' into devel 2009-12-05 10:35:33 +00:00
Russell King e28edb723e Merge branches 'at91', 'ep93xx', 'etm', 'ks8695', 'nuc', 'u300' and 'u8500' into devel 2009-12-05 10:35:18 +00:00
Dmitry Torokhov 467832032c Merge commit 'v2.6.32' into next 2009-12-02 23:38:13 -08:00
Nicolas Ferre 985f37f827 AT91: add touchscreen support for at91sam9g45ekes
New at91sam9g45ekes board provides a LCD with resistive touchscreen.
This is the support of this feature by atmel_tsadcc driver. This also
sets up platform parameters to be passed to the driver.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-11-20 00:55:38 -08:00
Nicolas Ferre 423c9b0dc3 AT91: add platform parameters for atmel_tsadcc in at91sam9rlek
Setup platform parameters in at91sam9rl-ek board to be passed to
atmel_tsadcc touchscreen.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-11-20 00:55:29 -08:00
Nicolas Ferre 0f74296a0f at91: at91sam9g20ek modify dual slot evaluation kit
at91sam9g20ek rev. C and onwards embed two SD/MMC slots. This patch modify the
previous dual slot board definition to match the official rev. C board. It also
allows the use of at91_mci SD/MMC driver in addition to the atmel-mci one.

Some pins have been re-affected from leds or Ethernet phy IRQ to the SD/MMC
slot A. This lead to a modification of those definitions.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
2009-11-16 16:57:50 +01:00
Nicolas Ferre 0912e5359f atmel_lcdfb Kconfig: remove long dependency line
Many Atmel SOC are embedding a LCD controller. This patch removes the long
dependency line for this Atmel LCD framebuffer driver configuration entry.
The HAVE_FB_ATMEL configuration option is located in the video Kconfig file
as it may be setup by ARM/AT91 and AVR32 chips.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
2009-11-16 16:56:23 +01:00
Jean-Christophe PLAGNIOL-VILLARD 2ef9f59a7a at91: Kconfig simplification
Instead of adding "depends on" at config level, introduce HAVE_* config
variables. Add them at machine or soc level to specify the ability of a
particular support.
It will ease new board introduction and readability.

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
2009-11-16 16:56:22 +01:00
Jean-Christophe PLAGNIOL-VILLARD c4e4ab9f23 at91: remove not needed depends on
Those "depends on" are a double check as all machine entries are
surrounded by "if <ARCH_xxx>" conditions.

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
2009-11-16 16:56:21 +01:00
Nicolas Ferre fdcad71cef at91: at91sam9g20ek modify dual slot evaluation kit
at91sam9g20ek rev. C and onwards embed two SD/MMC slots. This patch modify the
previous dual slot board definition to match the official rev. C board. It also
allows the use of at91_mci SD/MMC driver in addition to the atmel-mci one.

Some pins have been re-affected from leds or Ethernet phy IRQ to the SD/MMC
slot A. This lead to a modification of those definitions.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
2009-11-16 16:55:55 +01:00
Uwe Kleine-König 01c62c9b32 ARM: 5782/1: at91: support for eco920
CONFIG_MACH_ECO920 is enabled in at91rm9200dk_defconfig.  The name is
wrong, but this is better than adding another defconfig or don't get
compile coverage at all.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-11-10 23:46:35 +00:00
Albin Tonnerre 1ea60cf706 ARM: 5778/1: AT91: Add cpuidle support
This patch adds the support for cpuidle on AT91 SoCs, taken from the
cpuidle support in mach-kirkwood.
cpuidle needs sdram_selfrefresh_enable and _disable, so move their
definition to a separate header file instead of duplicating the code
already used in pm.c.

Tested-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-11-10 23:46:35 +00:00
Nicolas Ferre d8951adeba at91: at91sam9g45 family: identify several chip versions
cpu_is_xxx() macros are identifying generic at91sam9g45 chip. This patch adds
the capacity to differentiate Engineering Samples and final lots through the
inclusion of  at91_cpu_fully_identify() and the related chip IDs with chip
version field preserved.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
2009-11-03 18:42:31 +01:00
Nicolas Ferre f51f78c06c ARM: 5726/1: at91/USB: at91sam9g45 series USB host integration
This is the at91 specific part of USB host integration. The EHCI high speed
controller has a companion OHCI controller to manage USB full and low speed.
They are sharing the same IRQ line and vbus pin.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-10-25 16:00:33 +00:00
Yegor Yefremov 4726374fb4 ARM: 5766/1: Fix watchdog enabling for AT91SAM9G45
The macro for the watchdog has been changed from CONFIG_AT91SAM9_WATCHDOG
to CONFIG_AT91SAM9X_WATCHDOG due to AT91CAP9 chips support

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-10-21 13:08:14 +01:00
Linus Torvalds 5c3cc2084d Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (94 commits)
  genetlink: fix netns vs. netlink table locking (2)
  3c59x: Get rid of "Trying to free already-free IRQ"
  tunnel: eliminate recursion field
  ems_pci: fix size of CAN controllers BAR mapping for CPC-PCI v2
  net: fix htmldocs sunrpc, clnt.c
  Phonet: error on broadcast sending (unimplemented)
  Phonet: fix race for port number in concurrent bind()
  pktgen: better scheduler friendliness
  pktgen: T_TERMINATE flag is unused
  ipv4: check optlen for IP_MULTICAST_IF option
  ath9k: Initialize txgain and rxgain for newer AR9287 chipsets.
  iwlagn: fix panic in iwl{5000,4965}_rx_reply_tx
  ath9k: Fix RFKILL bugs
  drivers/net/wireless: Use usb_endpoint_dir_out
  cfg80211: don't overwrite privacy setting
  wl12xx: fix kconfig/link errors
  rt2x00: fix the definition of rt2x00crypto_rx_insert_iv
  iwlwifi: reduce noise when skb allocation fails
  iwlwifi: do not send sync command while holding spinlock
  mac80211: fix DTIM setting
  ...
2009-09-25 07:22:11 -07:00
David S. Miller 8b3f6af863 Merge branch 'master' of /home/davem/src/GIT/linux-2.6/
Conflicts:
	drivers/staging/Kconfig
	drivers/staging/Makefile
	drivers/staging/cpc-usb/TODO
	drivers/staging/cpc-usb/cpc-usb_drv.c
	drivers/staging/cpc-usb/cpc.h
	drivers/staging/cpc-usb/cpc_int.h
	drivers/staging/cpc-usb/cpcusb.h
2009-09-24 15:13:11 -07:00
Russell King baea7b946f Merge branch 'origin' into for-linus
Conflicts:
	MAINTAINERS
2009-09-24 21:22:33 +01:00
Rob Emanuele 864f38ebdc AT91: atmel-mci: Platform configuration to the the atmel-mci driver
Created a modified version of the at91sam9g20 evaluation kit platform
(board-sam9g20ek-2slot-mmc.c) and device support to make use of the
updated atmel-mci driver.

As the use of two slots modify GPIO pin allocation, we create another
board file.

This requires getting the most updated arch/arm/tools/mach-types from
http://www.arm.linux.org.uk/developer/machines/download.php to have the machine
type for the at91sam9g20ek-2slot-mmc board.

[nicolas.ferre@atmel.com: printk, slot_count modification in at91sam9260_devices.c file]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Rob Emanuele <rob@emanuele.us>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-23 07:39:37 -07:00
Marc Kleine-Budde a7a1a05f9d at91sam9263ek: activate at91 CAN controller
This patch activates the at91 CAN controller for the at91sam9263ek
development board.

Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-22 14:45:09 -07:00
Marc Kleine-Budde 58a587dc2a at91sam9263: add at91_can device to generic device definition
This patch adds the device definition for the at91_can device to
the generic device definiton file for the at91sam9263.

Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-22 14:45:06 -07:00
Russell King ae19ffbadc Merge branch 'master' into for-linus 2009-09-22 21:01:40 +01:00
Andrew Victor 9173a8ef24 ARM: 5719/1: [AT91] Fix AC97 breakage
Fix AC97 build breakage with converting to the shared AT91/AVR32 AC97 driver:
  struct atmel_ac97_data  -> struct ac97c_platform_data
  CONFIG_SND_AT91_AC97 -> CONFIG_SND_ATMEL_AC97C

Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-09-22 20:54:28 +01:00
Nicolas Ferre 439a33074c ARM: 5710/1: at91: add AC97 support to at91sam9rl and at91sam9rlek board
Add the support of AC97 on the at91sam9rl chip and -ek board.
It will share the code with AVR32 ac97c alsa driver "atmel_ac97c".

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-09-21 16:03:01 +01:00
Nicolas Ferre 378ac65e6c ARM: 5709/1: at91: add AC97 support to at91sam9g45 series and at91sam9m10g45ek board
Add the support of AC97 on the at91sam9g45 chip series and -ek board.
It will share the code with AVR32 ac97c alsa driver "atmel_ac97c".

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-09-21 16:02:59 +01:00
Nicolas Ferre 40262b2b6e ARM: 5621/1: at91/dmaengine: integration of at_hdmac driver in at91sam9g45 series
This is the integration of DMA engine driver into at91sam9g45 series
device file.
The associated driver is at_hdmac.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-09-21 16:02:15 +01:00
Nicolas Ferre 6ff89e9d62 ARM: 5620/1: at91/dmaengine: integration of at_hdmac driver in at91sam9rl
This is the integration of DMA engine driver into at91sam9rl device file. The
associated driver is at_hdmac.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-09-21 16:02:14 +01:00
Samuel R. C. Vale 4f37940d64 trivial: fix typos in comments s/DGBU/DBGU/
DBGU means Debug Unit, was refered as "DGBU" in some files. Fixed to "DBGU".

Signed-off-by: Samuel R. C. Vale <srcvale@holoscopio.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-09-21 15:14:55 +02:00
Russell King ddd559b13f Merge branch 'devel-stable' into devel
Conflicts:
	MAINTAINERS
	arch/arm/mm/fault.c
2009-09-12 12:02:26 +01:00
Russell King cf7a2b4fb6 Merge branches 'arm', 'at91', 'bcmring', 'ep93xx', 'mach-types', 'misc' and 'w90x900' into devel 2009-09-12 12:01:34 +01:00
Nicolas Ferre 8c3cbd5a2b ARM: 5686/1: at91: Correct AC97 reset line in at91sam9263ek board
Board code was wrongly setting up the reset pin for AC97 on at91sam9263ek.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-09-06 20:57:27 +01:00
sedji gaouaou d656f07a74 ARM: 5640/1: This patch modifies the support of AC97 on the at91sam9263 ek board
This patch modifies the support of AC97 on the at91sam9263 ek board, so it would
share the code with AVR32.
Plus it removes a typo in at91sam9263_devices.c.

Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-09-06 20:57:26 +01:00
Sergey Matyukevich 0c30df6fe0 ARM: 5632/1: Board-specific data for IDE support on afeb9260
This patch adds board-specific data for IDE support on afeb9260.

Depends on #5631/1

Tested-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Acked-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-08-01 16:24:59 +01:00
Sergey Matyukevich fb85205ada ARM: 5631/1: Platform data for CF/IDE support in AT91SAM9260
This patch adds platform data for CF/IDE support
and SMC init code for AT91SAM9260 SoC.

Tested-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-08-01 16:24:59 +01:00
Linus Torvalds db06816cb9 Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
  dmaengine: at_hdmac: add DMA slave transfers
  dmaengine: at_hdmac: new driver for the Atmel AHB DMA Controller
  dmaengine: dmatest: correct thread_count while using multiple thread per channel
  dmaengine: dmatest: add a maximum number of test iterations
  drivers/dma: Remove unnecessary semicolons
  drivers/dma/fsldma.c: Remove unnecessary semicolons
  dmaengine: move HIGHMEM64G restriction to ASYNC_TX_DMA
  fsldma: do not clear bandwidth control bits on the 83xx controller
  fsldma: enable external start for the 83xx controller
  fsldma: use PCI Read Multiple command
2009-07-30 16:46:31 -07:00
Eric Bénard 10233a9398 ARM: 5630/1: Add support for Eukrea's CPUAT91
CPUAT91 is based on Atmel's AT91RM9200 with up to 16MB Strataflash,
up to 128MB SDRAM and an ethernet PHY in RMII mode.

Signed-off-by: Eric Benard <ebenard@eukrea.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-07-30 17:48:41 +01:00
Eric Bénard 41a353d126 ARM: 5629/1: Add support for Eukrea's CPU9260 & CPU9G20
CPU9260 and CPU9G20 share the same PCB populated with either
Atmel's AT91SAM9260B or AT91SAM9G20B with up to 64MB Strataflash,
up to 128MB SDRAM, up to 2GB NAND and an ethernet PHY in RMII mode.

Signed-off-by: Eric Benard <eric@eukrea.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-07-30 17:48:40 +01:00
Nicolas Ferre 4c8abb556b ARM: 5622/1: at91: at91sam9g45 headers: DMA peripheral identifiers
It adds DMA peripheral identifiers for hardware handshaking interface. It will
be used in platform code.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-07-25 17:10:10 +01:00
Nicolas Ferre 808347f6a3 dmaengine: at_hdmac: add DMA slave transfers
This patch for at_hdmac adds the slave transfers capability to the Atmel DMA
controller available on some AT91 SOCs. This allow peripheral to memory and
memory to peripheral transfers with hardware handshaking.

Slave structure for controller specific information is passed through channel
private data. This at_dma_slave structure is defined in at_hdmac.h header file
and relative hardware definition are moved to this file from at_hdmac_regs.h.
Doing this we allow the channel configuration from platform definition code.

This work is intensively based on dw_dmac and several slave implementations.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2009-07-22 23:15:33 -07:00
Nicolas Ferre dc78baa2b9 dmaengine: at_hdmac: new driver for the Atmel AHB DMA Controller
This AHB DMA Controller (aka HDMA or DMAC on AT91 systems) is availlable on
at91sam9rl chip. It will be used on other products in the future.

This first release covers only the memory-to-memory tranfer type. This is the
only tranfer type supported by this chip.  On other products, it will be used
also for peripheral DMA transfer (slave API support to come).

I used dmatest client without problem in different configurations to test it.

Full documentation for this controller can be found in the SAM9RL datasheet:
http://www.atmel.com/dyn/products/product_card.asp?part_id=4243

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2009-07-22 22:41:27 -07:00
Mark Brown d7dbf6ea40 [ARM] 5596/1: at91sam9g20-ek: Register WM8731 in board file
The WM8731 driver has been updated to allow registration via normal
device model methods rather than from within the ASoC driver probe
so update the AT91SAM9G20-EK to make use of this.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-07-09 17:15:23 +01:00
Nicolas Ferre b319ff8085 [ARM] 5570/1: at91: Support for at91sam9g10: core chip & board support
From: Hong Xu <hong.xu@atmel.com>

Here are the modification to at91sam9261 files dedicated to the support of
at91sam9g10. This direction has been adopted to minimize code duplication.

All at91sam9261 drivers are enabled in _devices and board- files. Modificaton
to peripherals that support at91sam9g10 will be added in future patches.

Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-07-02 15:59:56 +01:00
Nicolas Ferre b784b7c037 [ARM] 5568/1: at91: Basic support for at91sam9g10: header files
From: Hong Xu <hong.xu@atmel.com>

AT91sam9g10 is an ARM 926ej-s SOC. It is an evolution of the at91sam9261 with a
faster clock speed: 266/133MHz.

Here is the basic header file support for this product.

Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-07-02 15:59:55 +01:00
Nicolas Ferre eab4170865 [ARM] 5567/1: at91: Support for at91sam9g10: clocks management
From: Hong Xu <hong.xu@atmel.com>

Add the at91sam9g10 support to the AT91 generic clock file. It takes
advantage of the management by functionalities of those PLLs and clocks.

Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-07-02 15:59:54 +01:00
Nicolas Ferre 59c5fe6d84 [ARM] 5562/2: at91: add gpio button support for at91sam9g20ek
This adds input keyboard gpio support on at91sam9g20ek board.
It adds button 3 and 4.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-06-29 11:19:27 +01:00
Nicolas Ferre 789b23bc40 [ARM] 5572/1: at91: Support for at91sam9g45 series: core chip & board support
Here are the at91 specific files dedicated to the at91sam9g45 series. They
mimic the traditional at91 way of managing chips & boards.

The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES. In
the future, the main board for this 9g45 series will be the
AT91SAM9M10G45-EK (I choose this last name for the board file).

Simple drivers are enabled in _devices and board- files. Newer peripheral
support will be added in future patches.

Incuded peripherals support (for now):
- USART
- SPI
- Ethernet
- NAND flash
- LCD
- gpio/joystick/buttons
- leds and pwm

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-06-27 11:05:22 +01:00
Nicolas Ferre fddcc0ae58 [ARM] 5571/1: at91: Basic support for at91sam9g45 series: header files.
AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz.
It embedds USB high speed host and device, LCD, DDR2 RAM, and a full set of
peripherals.

Here is the basic header file support for this product series.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-06-27 11:05:21 +01:00
Nicolas Ferre 2ef9df7ada [ARM] 5569/1: at91: Support for at91sam9g45: clocks management
Add the at91sam9g45 series support to the AT91 generic clock file.
This takes care of the particularities of the PMC for this series.
It also takes advantage of the management by functionalities of
those PLLs and clocks.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-06-27 11:05:20 +01:00
Ryan Mallon 7c6425a040 [ARM] 5566/1: Remove at91_gpiolib_request
Remove at91_gpiolib_request. It returns -EPERM if a request pin is not
in GPIO mode, however we want to be able to gpio_request alternative
function pins to reserve them, and in some cases we need to be able to
use the gpiolib functions on alternative function pins.

Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-06-27 11:03:47 +01:00
Nicolas Ferre 226ddb9833 [ARM] 5564/1: at91: add gpio button and leds support for at91sam9rlek
This adds input keyboard gpio support on at91sam9rlek board. It adds button 1
and 2 (left and right click).
It also adds gpio leds ds1, ds2 and ds3.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-06-27 11:03:29 +01:00
Nicolas Ferre 9a24ee03ae [ARM] 5563/1: at91: at91sam9rlek lcd interface correction
Here is a little update to the at91sam9rlek lcd interface.
This will correct the power pin of the LCD.
It will also add precision to the struct atmel_lcdfb_info
scructure: backlight enabling  and wiring mode correction:
RGB wiring on the -EK board.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-06-27 11:02:24 +01:00
Sergey Lapin 6d36110e1c [ARM] 5525/1: AFEB9260: fix for MMC support
Proper pin configuration for MMC.

Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-05-29 20:17:40 +01:00
Dmitry Baryshkov 6953e47e11 [ARM] 5524/1: at91sam9g20ek: add i2c eeprom info
Add board information about on-board I2C eeprom AT24C512N at 0x50.

Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-05-29 20:17:39 +01:00
Sergey Lapin 34e559eabf [ARM] 5514/1: AFEB9260 sound support
ASoC driver for AT91SAM9260-based AFEB9260 board

Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-05-24 19:20:02 +01:00
Nicolas Ferre 6d0485a993 [ARM] 5438/1: AT91: manage clock by functionality instead of CPUs
In clock.c file the clock management is grouped by cpu with cpu_is_xxx()
function. This lead to some kind of difficulties to read this file and
maintainability issues as the number of AT91 cpus & PLLs/clocks is growing.

In this patch, I try to group clock functionality together and match cpus with
this functionality set.
An update to at91_pmc.h is needed to cover some new PMC possibilities (and
some update in comments).

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <avictor.za@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-04-28 22:44:55 +01:00
Magnus Damm 8e19608e8b clocksource: pass clocksource to read() callback
Pass clocksource pointer to the read() callback for clocksources.  This
allows us to share the callback between multiple instances.

[hugh@veritas.com: fix powerpc build of clocksource pass clocksource mods]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-21 13:41:47 -07:00
Justin Waters d0176f612f [ARM] 5445/1: AT91: Remove flexible array from USBH platform data
The flexible array in the USBH platform data is not safe to copy.  The
compiler will not allocate any extra memory for the non-init platform
data structure (in the *_devices.c files) since it isn't given any
defaults at compile time.  When the probe function attempts to address
that array, it will actually attempt to access data in an adjacent
structure.

Since there are currently no (known) implementations of the at91 USBH
IP with more than 2 vbus pins, I am capping the value at 2.  If somebody
tries to assign more, then the compiler will produce a warning.

Signed-off-by: Justin Waters <justin.waters@timesys.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-04-08 20:36:16 +01:00
Ryan Mallon 7f96b1caac [ARM] 5441/1: Use pr_err on error paths in at91 pm
Change pr_debug to pr_err on error paths in the AT91 power management
code. All of the errors will result in the cpu not going into the
suspend state. This patch makes it possible to identify problems with
suspend when power management debugging is not enabled.

Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-04-01 22:18:19 +01:00
Russell King be093beb60 [ARM] pass reboot command line to arch_reset()
OMAP wishes to pass state to the boot loader upon reboot in order to
instruct it whether to wait for USB-based reflashing or not.  There is
already a facility to do this via the reboot() syscall, except we ignore
the string passed to machine_restart().

This patch fixes things to pass this string to arch_reset().  This means
that we keep the reboot mode limited to telling the kernel _how_ to
perform the reboot which should be independent of what we request the
boot loader to do.

Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-03-19 16:20:24 +00:00
Russell King 97fb44eb6b Merge branch 'for-rmk' of git://git.pengutronix.de/git/imx/linux-2.6 into devel
Conflicts:

	arch/arm/mach-at91/gpio.c
2009-03-13 21:44:51 +00:00
Stanislaw Gruszka e565f20608 AT91: initialize Compact Flash on AT91SAM9263 cpu
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Andrew Victor <avictor.za@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2009-03-05 16:10:58 +01:00
Stanislaw Gruszka 6e5f1e1115 ide: add at91_ide driver
This is IDE host driver for AT91 (SAM9, CAP9, AT572D940HF) Static Memory
Controller with Compact Flash True IDE Mode logic.

Driver have to switch 8/16 bit bus width when accessing Task Tile or Data
Register. Moreover some extra things need to be done when setting PIO mode.
Only PIO mode is used, hardware have no DMA support. If interrupt line is
connected through GPIO extra quirk is needed to cope with fake interrupts.

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Andrew Victor <avictor.za@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2009-03-05 16:10:58 +01:00
Andrei Birjukov d82ad6d683 [ARM] at91: fix for Atmel AT91 powersaving
We've discovered that our AT91SAM9260 board consumed too much power when
returning from a slowclock low-power mode.  RAM self-refresh is enabled in
a bootloader in our case, this is how we saw a difference.  Estimated ca.
30mA more on 4V battery than the same state before powersaving.

After a small research we found that there seems to be a bogus
sdram_selfrefresh_disable() call at the end of at91_pm_enter() call, which
overwrites the LPR register with uninitialized value.  Please find the
suggested patch attached.

This patch fixes correct restoring of LPR register of the Atmel AT91 SDRAM
controller when returning from a power saving mode.

Signed-off-by: Andrei Birjukov <andrei.birjukov@artecdesign.ee>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-02-22 22:37:21 +00:00
Mark Brown 423145a5d4 [ARM] 5399/1: [AT91] Configure MCLK and SSC for AT91SAMG20-EK
The AT91SAM20-EK has a WM8731 attached to it with MCLK supplied from
PCLK0 and the digital audio interface supplied by SSC0.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-02-21 16:39:40 +00:00
Gregory CLEMENT 744f659272 [ARM] 5400/1: Add support for inverted rdy_busy pin for Atmel nand device controller
Add support for inverted rdy_busy pin for Atmel nand device controller
It will fix building error on NeoCore926 board.

Acked-by: Andrew Victor <linux@maxim.org.za>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Gregory CLEMENT <gclement@adeneo.adetelgroup.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-02-16 21:40:39 +00:00
Andrew Victor 2b768b6cdb [ARM] 5391/1: AT91: Enable GPIO clocks earlier
Enable the GPIO clocks earlier in the initialization sequence.  This
allow the board-setup code to read and set GPIO pins.

Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-02-14 16:03:36 +00:00
Andrew Victor 2af29b7861 [ARM] 5390/1: AT91: Watchdog fixes
The recently merged AT91SAM9 watchdog driver uses the
AT91SAM9X_WATCHDOG config variable, whereas the original version of
the driver (and the platform support code) used AT91SAM9_WATCHDOG.
This causes the watchdog platform_device to never be registered, and
therefore the driver not to be initialized.

This patch:
- updates the platform support code to use AT91SAM9X_WATCHDOG.
- includes <linux/io.h> to fix compile error (same fix as was applied
to at91rm9200_wdt.c)
- fixes comment regarding watchdog clock-rates in at91rm9200.

Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-02-14 16:01:57 +00:00
Ryan Mallon f373e8c063 [ARM] 5373/2: Add gpiolib support to AT91
Add support for gpiolib, including debugfs output, to the AT91 family.
The at91_get/set_gpio_value calls still exist since they are used by the
atmel serial driver.

Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-02-12 10:45:08 +00:00
Russell King 80b02c172b [ARM] fix AT91, davinci, h720x, ks8695, msm, mx2, mx3, netx, omap1, omap2, pxa, s3c
arch/arm/mach-at91/at91cap9.c:337: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91rm9200.c:301: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9260.c:351: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9261.c:287: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9263.c:312: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9rl.c:304: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-h720x/h7202-eval.c:38: error: implicit declaration of function 'IRQ_CHAINED_GPIOB'
arch/arm/mach-ks8695/devices.c:46: error: 'KS8695_IRQ_WAN_RX_STATUS' undeclared here (not in a function)
arch/arm/mach-msm/devices.c:28: error: 'INT_UART1' undeclared here (not in a function)
arch/arm/mach-mx2/devices.c:233: error: 'MXC_GPIO_IRQ_START' undeclared here (not in a function)
arch/arm/mach-mx3/devices.c:128: error: 'MXC_GPIO_IRQ_START' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:140: error: 'INT_730_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:165: error: 'INT_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:200: error: 'INT_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap2/board-apollon.c:286: error: implicit declaration of function 'omap_set_gpio_direction'
arch/arm/mach-omap2/mcbsp.c:154: error: 'INT_24XX_MCBSP1_IRQ_RX' undeclared here (not in a function)
arch/arm/mach-omap2/mcbsp.c:181: error: 'INT_24XX_MCBSP1_IRQ_RX' undeclared here (not in a function)
arch/arm/mach-pxa/e350.c:36: error: 'IRQ_BOARD_START' undeclared here (not in a function)
arch/arm/plat-s3c/dev-i2c0.c:32: error: 'IRQ_IIC' undeclared here (not in a function)
...

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-01-08 16:29:42 +00:00
Linus Torvalds b840d79631 Merge branch 'cpus4096-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'cpus4096-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (66 commits)
  x86: export vector_used_by_percpu_irq
  x86: use logical apicid in x2apic_cluster's x2apic_cpu_mask_to_apicid_and()
  sched: nominate preferred wakeup cpu, fix
  x86: fix lguest used_vectors breakage, -v2
  x86: fix warning in arch/x86/kernel/io_apic.c
  sched: fix warning in kernel/sched.c
  sched: move test_sd_parent() to an SMP section of sched.h
  sched: add SD_BALANCE_NEWIDLE at MC and CPU level for sched_mc>0
  sched: activate active load balancing in new idle cpus
  sched: bias task wakeups to preferred semi-idle packages
  sched: nominate preferred wakeup cpu
  sched: favour lower logical cpu number for sched_mc balance
  sched: framework for sched_mc/smt_power_savings=N
  sched: convert BALANCE_FOR_xx_POWER to inline functions
  x86: use possible_cpus=NUM to extend the possible cpus allowed
  x86: fix cpu_mask_to_apicid_and to include cpu_online_mask
  x86: update io_apic.c to the new cpumask code
  x86: Introduce topology_core_cpumask()/topology_thread_cpumask()
  x86: xen: use smp_call_function_many()
  x86: use work_on_cpu in x86/kernel/cpu/mcheck/mce_amd_64.c
  ...

Fixed up trivial conflict in kernel/time/tick-sched.c manually
2009-01-02 11:44:09 -08:00
Russell King 828aac2ee2 Merge branch 'for-rmk' of git://git.pengutronix.de/git/ukl/linux-2.6 into devel 2008-12-19 19:46:52 +00:00
Rusty Russell 320ab2b0b1 cpumask: convert struct clock_event_device to cpumask pointers.
Impact: change calling convention of existing clock_event APIs

struct clock_event_timer's cpumask field gets changed to take pointer,
as does the ->broadcast function.

Another single-patch change.  For safety, we BUG_ON() in
clockevents_register_device() if it's not set.

Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
2008-12-13 21:20:26 +10:30
Uwe Kleine-König c4edfced66 at91: warn if irqs are enabled in set_next_event
Thomas claims that irqs are disabled when set_next_event is called.  But
David and Remy claim they saw irqs being enabled here.  As both sides
don't seem to have time to investigate here, start with a warning that
might trigger if the problem still exists.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-By: David Brownell <dbrownell@users.sourceforge.net>
Cc: Bill Gatliff <bgat@billgatliff.com>
Acked-By: Remy Bohmer <linux@bohmer.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
2008-12-12 11:17:08 +01:00
Stelian Pop 7be90a6ba9 [ARM] 5319/1: AT91: support AT91CAP9 revC CPUs
The AT91CAP9 revC CPU has a few differences over the previous,
revB CPU which was distributed in small quantities only (revA was
an internal Atmel product only).

This patch adds the detection routines to recognize the different
AT91CAP9 revisions (based on the PMC subsystem version number), and
uses them to:
	- activate a workaround for the external interrupts levels
	  (on revB CPUs)
	- set the UDPHS_BYPASS bit (on revB CPUs)
	- set AT91_GPBR register address to the correct offset
	  (0xfffffd50 on revB, 0xfffffd60 on revC)

For debugging usage, the CPU revision can be found in /proc/cpuinfo
on the 'Revision' line.

This patch is extracted from Andrew Victor's -at91 patch (2.6.27-at91.patch)
where it has been tested for the last 6 months.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-12-01 17:22:07 +00:00
Andrew Victor ffc63b7d30 [ARM] 5290/1: [AT91] Add support for the Adeneo NeoCore 926 board
Add support for the Adeneo NeoCore 926 board.

Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-12-01 17:18:15 +00:00
Andrew Victor 8cdae51aa9 [ARM] 5289/1: [AT91] Convert boards to use sam9_smc_configure()
Convert the SAM9 and CAP9 board-specific files to make use of the
sam9_smc_configure() method to configure the memory-controller for
external peripherals.

The following boards have been modified:
 cam60 : NAND
 cap9adk : NAND, NOR
 qil-a9260 : NAND
 sam9-l9260 : NAND
 sam9260ek : NAND
 sam9261ek : DM9000 Ethernet, NAND
 sam9263 : NAND
 sam9g20ek : NAND
 sam9rlek : NAND
 usb-a9260 : NAND
 usb-a9263 .: NAND

Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-12-01 17:18:13 +00:00
Andrew Victor 461d3b4dcf [ARM] 5288/1: [AT91] Remove SMC configuration from devices.c files
In at91_add_device_nand(), do not configure the Static Memory
controller with specific timing values.
The *_devices.c files are board independent, and the SMC timing values
are specific to the NAND devices that are installed on the board.
The board-specific files are now responsible for configuring the
Static Memory controller (if the don't want to leave it up to a
bootloader).

Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-12-01 17:18:10 +00:00