IPvlan setup uses one mac-address (of master). The IPv6 link-local
addresses are derived using the mac-address on the link. Lack of
dev-ids makes these link-local addresses same for all slaves including
that of master device. dev-ids are necessary to add differentiation
when L2 address is shared.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In an IPvlan setup when master is set in loopback mode e.g.
ethtool -K eth0 set loopback on
where eth0 is master device for IPvlan setup.
The failure is caused by the faulty logic that determines if the
packet is from TX-path vs. RX-path by just looking at the mac-
addresses on the packet while processing multicast packets.
In the loopback-mode where this crash was happening, the packets
that are sent out are reflected by the NIC and are processed on
the RX path, but mac-address check tricks into thinking this
packet is from TX path and falsely uses dev_forward_skb() to pass
packets to the slave (virtual) devices.
This patch records the path while queueing packets and eliminates
logic of looking at mac-addresses for the same decision.
------------[ cut here ]------------
kernel BUG at include/linux/skbuff.h:1737!
Call Trace:
[<ffffffff921fbbc2>] dev_forward_skb+0x92/0xd0
[<ffffffffc031ac65>] ipvlan_process_multicast+0x395/0x4c0 [ipvlan]
[<ffffffffc031a9a7>] ? ipvlan_process_multicast+0xd7/0x4c0 [ipvlan]
[<ffffffff91cdfea7>] ? process_one_work+0x147/0x660
[<ffffffff91cdff09>] process_one_work+0x1a9/0x660
[<ffffffff91cdfea7>] ? process_one_work+0x147/0x660
[<ffffffff91ce086d>] worker_thread+0x11d/0x360
[<ffffffff91ce0750>] ? rescuer_thread+0x350/0x350
[<ffffffff91ce960b>] kthread+0xdb/0xe0
[<ffffffff91c05c70>] ? _raw_spin_unlock_irq+0x30/0x50
[<ffffffff91ce9530>] ? flush_kthread_worker+0xc0/0xc0
[<ffffffff92348b7a>] ret_from_fork+0x9a/0xd0
[<ffffffff91ce9530>] ? flush_kthread_worker+0xc0/0xc0
Fixes: ba35f8588f ("ipvlan: Defer multicast / broadcast processing to a work-queue")
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
CC: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two functions which would free the ipvl_port now. The first
is ipvlan_port_create. It frees the ipvl_port in the error handler,
so it could kfree it directly. The second is ipvlan_port_destroy. It
invokes netdev_rx_handler_unregister which enforces one grace period
by synchronize_net firstly, so it also could kfree the ipvl_port
directly and safely.
So it is unnecessary to use kfree_rcu to free ipvl_port.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mtu_adj is initialized to zero when alloc mem, there is no any
assignment to mtu_adj. It is only used in ipvlan_adjust_mtu as one
right value.
So it is useless member of struct ipvl_dev, then remove it.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a typical IPvlan L3 setup where master is in default-ns and
each slave is into different (slave) ns. In this setup egress
packet processing for traffic originating from slave-ns will
hit all NF_HOOKs in slave-ns as well as default-ns. However same
is not true for ingress processing. All these NF_HOOKs are
hit only in the slave-ns skipping them in the default-ns.
IPvlan in L3 mode is restrictive and if admins want to deploy
iptables rules in default-ns, this asymmetric data path makes it
impossible to do so.
This patch makes use of the l3_rcv() (added as part of l3mdev
enhancements) to perform input route lookup on RX packets without
changing the skb->dev and then uses nf_hook at NF_INET_LOCAL_IN
to change the skb->dev just before handing over skb to L4.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
CC: David Ahern <dsa@cumulusnetworks.com>
Reviewed-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. scope correction for few functions that are used in single file.
2. Adjust variables that are used in fast-path to fit into single cacheline
3. Update rcv_frame() to skip shared check for frames coming over wire
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mode argument was erronusly defined as u32 but it has always
been u16. Also use ipvlan_set_mode() helper to set the mode instead
of assigning directly. This should avoid future erronus assignments /
updates.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All structures used in traffic forwarding are rcu-protected:
ipvl_addr, ipvl_dev and ipvl_port. Thus we can unhash addresses
without synchronization. We'll anyway hash it back into the same
bucket: in worst case lockless lookup will scan hash once again.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
They are unused after commit f631c44bbe ("ipvlan: Always set broadcast bit in
multicast filter").
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing multicast / broadcast in fast path is performance draining
and having more links means more cloning and bringing performance
down further.
Broadcast; in particular, need to be given to all the virtual links.
Earlier tricks of enabling broadcast bit for IPv4 only interfaces are not
really working since it fails autoconf. Which means enabling broadcast
for all the links if protocol specific hacks do not have to be added into
the driver.
This patch defers all (incoming as well as outgoing) multicast traffic to
a work-queue leaving only the unicast traffic in the fast-path. Now if we
need to apply any additional tricks to further reduce the impact of this
(multicast / broadcast) type of traffic, it can be implemented while
processing this work without affecting the fast-path.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an ipvlan interface is down, its addresses are not on the hash list.
Fix checks for existence of addresses not to depend on the hash list, walk
through all interface addresses instead.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cosmetic patch to add __percpu qualifier to pcpu_stats
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the port check [ipvlan_dev_master()] and device check
[ipvlan_dev_slave()] functions to netdevice.h and rename them
netif_is_ipvlan_port() and netif_is_ipvlan() resp. to be
consistent with macvlan api naming.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver uses ip_out_local() and ip6_route_output() which are
defined only if CONFIG_INET and CONFIG_IPV6 are enabled respectively.
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver is very similar to the macvlan driver except that it
uses L3 on the frame to determine the logical interface while
functioning as packet dispatcher. It inherits L2 of the master
device hence the packets on wire will have the same L2 for all
the packets originating from all virtual devices off of the same
master device.
This driver was developed keeping the namespace use-case in
mind. Hence most of the examples given here take that as the
base setup where main-device belongs to the default-ns and
virtual devices are assigned to the additional namespaces.
The device operates in two different modes and the difference
in these two modes in primarily in the TX side.
(a) L2 mode : In this mode, the device behaves as a L2 device.
TX processing upto L2 happens on the stack of the virtual device
associated with (namespace). Packets are switched after that
into the main device (default-ns) and queued for xmit.
RX processing is simple and all multicast, broadcast (if
applicable), and unicast belonging to the address(es) are
delivered to the virtual devices.
(b) L3 mode : In this mode, the device behaves like a L3 device.
TX processing upto L3 happens on the stack of the virtual device
associated with (namespace). Packets are switched to the
main-device (default-ns) for the L2 processing. Hence the routing
table of the default-ns will be used in this mode.
RX processins is somewhat similar to the L2 mode except that in
this mode only Unicast packets are delivered to the virtual device
while main-dev will handle all other packets.
The devices can be added using the "ip" command from the iproute2
package -
ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ]
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Laurent Chavey <chavey@google.com>
Cc: Tim Hockin <thockin@google.com>
Cc: Brandon Philips <brandon.philips@coreos.com>
Cc: Pavel Emelianov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mahesh Bandewar