Fix the build:
arch/x86/platform/ce4100/ce4100.c: In function 'x86_ce4100_early_setup':
arch/x86/platform/ce4100/ce4100.c:165:2: error: 'reboot_type' undeclared (first use in this function)
Reported-by: Wu Fengguang <fengguang.wu@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull x86 fixes from Peter Anvin:
"Trying again to get the fixes queue, including the fixed IDT alignment
patch.
The UEFI patch is by far the biggest issue at hand: it is currently
causing quite a few machines to boot. Which is sad, because the only
reason they would is because their BIOSes touch memory that has
already been freed. The other major issue is that we finally have
tracked down the root cause of a significant number of machines
failing to suspend/resume"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Make sure IDT is page aligned
x86, suspend: Handle CPUs which fail to #GP on RDMSR
x86/platform/ce4100: Add header file for reboot type
Revert "UEFI: Don't pass boot services regions to SetVirtualAddressMap()"
efivars: check for EFI_RUNTIME_SERVICES
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
are flagged as __cpuinit -- so if we remove the __cpuinit from
arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
content into no-ops as early as possible, since that will get rid
of these warnings. In any case, they are temporary and harmless.
This removes all the arch/x86 uses of the __cpuinit macros from
all C files. x86 only had the one __CPUINIT used in assembly files,
and it wasn't paired off with a .previous or a __FINIT, so we can
delete it directly w/o any corresponding additional change there.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Here's the big tty/serial tree set of changes for 3.8-rc1.
Contained in here is a bunch more reworks of the tty port layer from Jiri and
bugfixes from Alan, along with a number of other tty and serial driver updates
by the various driver authors.
Also, Jiri has been coerced^Wconvinced to be the co-maintainer of the TTY
layer, which is much appreciated by me.
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDHhgwACgkQMUfUDdst+ynI6wCcC+YeBwncnoWHvwLAJOwAZpUL
bysAn28o780/lOsTzp3P1Qcjvo69nldo
=hN/g
-----END PGP SIGNATURE-----
Merge tag 'tty-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY/Serial merge from Greg Kroah-Hartman:
"Here's the big tty/serial tree set of changes for 3.8-rc1.
Contained in here is a bunch more reworks of the tty port layer from
Jiri and bugfixes from Alan, along with a number of other tty and
serial driver updates by the various driver authors.
Also, Jiri has been coerced^Wconvinced to be the co-maintainer of the
TTY layer, which is much appreciated by me.
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fixed up some trivial conflicts in the staging tree, due to the fwserial
driver having come in both ways (but fixed up a bit in the serial tree),
and the ioctl handling in the dgrp driver having been done slightly
differently (staging tree got that one right, and removed both
TIOCGSOFTCAR and TIOCSSOFTCAR).
* tag 'tty-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (146 commits)
staging: sb105x: fix potential NULL pointer dereference in mp_chars_in_buffer()
staging/fwserial: Remove superfluous free
staging/fwserial: Use WARN_ONCE when port table is corrupted
staging/fwserial: Destruct embedded tty_port on teardown
staging/fwserial: Fix build breakage when !CONFIG_BUG
staging: fwserial: Add TTY-over-Firewire serial driver
drivers/tty/serial/serial_core.c: clean up HIGH_BITS_OFFSET usage
staging: dgrp: dgrp_tty.c: Audit the return values of get/put_user()
staging: dgrp: dgrp_tty.c: Remove the TIOCSSOFTCAR ioctl handler from dgrp driver
serial: ifx6x60: Add modem power off function in the platform reboot process
serial: mxs-auart: unmap the scatter list before we copy the data
serial: mxs-auart: disable the Receive Timeout Interrupt when DMA is enabled
serial: max310x: Setup missing "can_sleep" field for GPIO
tty/serial: fix ifx6x60.c declaration warning
serial: samsung: add devicetree properties for non-Exynos SoCs
serial: samsung: fix potential soft lockup during uart write
tty: vt: Remove redundant null check before kfree.
tty/8250 Add check for pci_ioremap_bar failure
tty/8250 Add support for Commtech's Fastcom Async-335 and Fastcom Async-PCIe cards
tty/8250 Add XR17D15x devices to the exar_handle_irq override
...
The default reboot is via ACPI for this platform, and the CEFDK
bootloader actually supports this, but will issue a system power
off instead of a real reboot. Setting the reboot method to be
KBD instead of ACPI ensures proper system reboot.
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Cc: rui.zhang@intel.com
Cc: alan@linux.intel.com
Link: http://lkml.kernel.org/r/1351518020-25556-3-git-send-email-ffainelli@freebox.fr
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The CE4100 platform is currently missing a proper pm_poweroff
implementation leading to poweroff making the CPU spin forever
and the CE4100 platform does not enter a low-power mode where
the external Power Management Unit can properly power off the
system. Power off on this platform is implemented pretty much
like reboot, by writing to the SoC built-in 8051 microcontroller
mapped at I/O port 0xcf9, the value 0x4.
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: rui.zhang@intel.com
Cc: alan@linux.intel.com
Link: http://lkml.kernel.org/r/1351518020-25556-2-git-send-email-ffainelli@freebox.fr
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The current CE4100 and 8250_pci code have both a limitation preventing the
registration and usage of CE4100's second UART. This patch changes the
platform code fixing up the UART port to work on a relative UART port
base address, as well as the 8250_pci code to make it register 2 UART ports
for CE4100 and pass the port index down to all consumers.
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sodaville has GPIO controller behind the PCI bus. To my suprissed it is
not the same as on PXA.
The interrupt & gpio chip can be referenced from the device tree like
from any other driver. Unfortunately the driver which uses the gpio
interrupt has to use irq_of_parse_and_map() instead of
platform_get_irq(). The problem is that the platform device (which is
created from the device tree) is most likely created before the
interrupt chip is registered and therefore irq_of_parse_and_map() fails.
In theory the driver works as module. In reality most of the irq
functions are not exported to modules and it is possible that _this_
module is unloaded while the provided irqs are still in use.
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
[torbenh@linutronix.de: make it work after the irq namespace cleanup,
add some device tree entries.]
Signed-off-by: Torben Hohn <torbenh@linutronix.de>
[bigeasy@linutronix.de: convert to generic irq & gpio chip]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
[grant.likely@secretlab.ca: depend on x86 to avoid irq_domain breakage]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix a build error. CE4100 with no serial errors because the alternate
function is only a prototype not a null function as intended.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The USB and SATA ioapic interrrupt pins are configured as edge type,
but need to be level type interrupts to work correctly.
[ tglx: Split out from the combo patch ]
Cc: Torben Hohn <torbenh@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/%3C20110427143052.GA15211%40linutronix.de%3E
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
without the reg property Ben's new code won't find the PCI & ISA
bridge and the devices won't get the DT-node attached.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: monstr@monstr.eu
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Link: http://lkml.kernel.org/r/20110407121315.GA9204@linutronix.de
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (27 commits)
x86: Clean up apic.c and apic.h
x86: Remove superflous goal definition of tsc_sync
x86: dt: Correct local apic documentation in device tree bindings
x86: dt: Cleanup local apic setup
x86: dt: Fix OLPC=y/INTEL_CE=n build
rtc: cmos: Add OF bindings
x86: ce4100: Use OF to setup devices
x86: ioapic: Add OF bindings for IO_APIC
x86: dtb: Add generic bus probe
x86: dtb: Add support for PCI devices backed by dtb nodes
x86: dtb: Add device tree support for HPET
x86: dtb: Add early parsing of IO_APIC
x86: dtb: Add irq domain abstraction
x86: dtb: Add a device tree for CE4100
x86: Add device tree support
x86: e820: Remove conditional early mapping in parse_e820_ext
x86: OLPC: Make OLPC=n build again
x86: OLPC: Remove extra OLPC_OPENFIRMWARE_DT indirection
x86: OLPC: Cleanup config maze completely
x86: OLPC: Hide OLPC_OPENFIRMWARE config switch
...
Fix up conflicts in arch/x86/platform/ce4100/ce4100.c
Setting the pci ops on subsys initcall unconditionally will break
multi platform kernels on anything except ce4100.
Use x86_init.pci.init ops to call this only on real ce4100 platforms.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: sodaville@linutronix.de
LKML-Reference: <20110314093340.GA21026@www.tglx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Up to now we force enable the local apic in the devicetree setup
uncoditionally and set smp_found_config unconditionally to 1 when a
devicetree blob is available. This breaks, when local apic is disabled
in the Kconfig.
Make it consistent by initializing device tree explicitely before
smp_get_config() so a non lapic configuration could be used as well.
To be functional that would require to implement PIT as an interrupt
host, but the only user of this code until now is ce4100 which
requires apics to be available. So we leave this up to those who need
it.
Tested-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use device tree information to setup IO_APIC configuration, interrupt
routing, HPET and everything else which cannot be enumerated by other
means.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: sodaville@linutronix.de
Cc: devicetree-discuss@lists.ozlabs.org
LKML-Reference: <1298405266-1624-11-git-send-email-bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
History:
v1..v2:
- dropped device_type except for cpu & pci. I have the compatible string
for pci so I can drop the device_type once it is possible
- I lowercased all compatible types. I will need to resend some patches
which have upper case intel
- The cpu had the same compatible string as the soc node. So I added to
the soc node -immr for internel memory mapped registers.
- I added generic names for all parts.
- I reworked the i2c bars matching the way you suggested. I added a
compatible node for the PCI device which only the PCI ids in its
compatible string. The bars (each represents a complete i2c
controller) have a "intel,ce4100-i2c-controller" compatible node. It
is not used by the driver.
The driver is probed via PCI ids (by the pci subsystem not OF) and
matches the bar address against the ressource in the child node. Once
there is a hit the node is attached.
- The SPI driver is also probed via pci. However I also attached a
compatible property based on PCI ids
v2..v3:
- intel,ce4100-immr become intel,ce4100-cp. cp stands for core
peripherals. The Atom data sheet talks here about ACPI devices. Since
we don't have ACPI this does not apply here.
- The interrupt map is gone. There are now plenty of device nodes.
- The "unit address string" got fixed, it uses not DD,V format.
v3..v4:
- added descriptions for compatible nodes introduced here:
- intel,ce4100-ioapic
- intel,ce4100-lapic
- intel,ce4100-hpet
- intel,ce4100
- intel,ce4100-cp
- intel,ce4100-pci
- added a description about I2C controller magic.
- Added gpio-controller and gpio-cells property to gpio devices. Those
properties are not (yet) used.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: sodaville@linutronix.de
Cc: devicetree-discuss@lists.ozlabs.org
LKML-Reference: <1298405266-1624-4-git-send-email-bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch enables the UART on the CE4100. The UART has a couple of
issues that need to be worked around. First the UART is mostly PC
compatible except that it is clocked eight times faster than a
standard PC so the default configuration provided in
arch/x86/include/asm/serial.h needs to be overridden. Second the TX
interrupt may not be set correctly all the time. Lastly accessing the
UART via I/O space for early_prink() hangs the chip when the IOAPIC is
enabled.
A custom mem_serial_in() is provided to work around the TX interrupt
issue. The configuration issues are dealt with in the call back
registered with the 8250 driver via serial8250_set_isa_configurator()
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
LKML-Reference: <1290436128-17958-1-git-send-email-dirk.brandewie@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Andrew Morton