We currently read how sibling lane adapter ports relate each other from
DROM (Device ROM). If the two lane adapter ports go through the same
physical connector these lanes can then be bonded together. However,
some cases DROM does not provide this information or it is missing
completely (host routers typically do not have DROM). In this case we
have hard-coded the relationship.
Expand this to work with both legacy devices where lane adapter ports 1
and 2, and 3 and 4 are always linked together, and with USB4 devices
where lane adapter 1 is always following lane adapter 0 or is disabled
completely (see USB4 section 5.2.1 for more information).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Lane bonding allows aggregating two 10/20 Gb/s (depending on the
generation) lanes into a single 20/40 Gb/s bonded link. This allows
sharing the full bandwidth more efficiently. In order to establish lane
bonding we need to check that lane bonding is possible through link
controller and that both ends of the link actually supports 2x widths.
This also means that all the paths should be established through the
primary port so update tb_path_alloc() to handle this as well.
Lane bonding is supported starting from Falcon Ridge (2nd generation)
controllers.
We also expose the current speed and number of lanes under each device
except the host router following similar attribute naming than USB bus.
Expose speed and number of lanes for both directions to allow possibility
of asymmetric link in the future.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
There are quite many places in the driver where we iterate over each
port in the switch. To make it bit more convenient, add a macro that can
be used to iterate over each port and convert existing call sites to use it.
This is based on code by Lukas Wunner.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Now that USB4 spec has names for these DP adapter registers we can use
them instead. This makes it easier to match certain register to the spec.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Now that USB4 spec has names for these PCIe adapter registers we can use
them instead. This makes it easier to match certain register to the spec.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Now that USB4 spec has names for these basic registers we can use them
instead. This makes it easier to match certain register to the spec.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
If we fail to add a switch for some reason log an error instead of
keeping silent. This is useful for debugging.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We currently differentiate between SW CM (Software Connection Manager,
sometimes also called External Connection Manager) and ICM (Firmware
based Connection Manager, Internal Connection Manager) by looking
directly at the sw->config.enabled field which may be rather hard to
understand for the casual reader. For this reason introduce a wrapper
function with documentation that should make the intention more clear.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The Thunderbolt standard went through several major iterations, here
called generation. USB4, which will be based on Thunderbolt, will be
generation 4. Let userspace know the generation of the controller in
the devices in order to distinguish between Thunderbolt and USB4, so
it can be shown in various user interfaces.
Signed-off-by: Christian Kellner <christian@kellner.me>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When lockdep is enabled, plugging Thunderbolt dock on Dominik's laptop
triggers following splat:
======================================================
WARNING: possible circular locking dependency detected
5.3.0-rc6+ #1 Tainted: G T
------------------------------------------------------
pool-/usr/lib/b/1258 is trying to acquire lock:
000000005ab0ad43 (pci_rescan_remove_lock){+.+.}, at: authorized_store+0xe8/0x210
but task is already holding lock:
00000000bfb796b5 (&tb->lock){+.+.}, at: authorized_store+0x7c/0x210
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&tb->lock){+.+.}:
__mutex_lock+0xac/0x9a0
tb_domain_add+0x2d/0x130
nhi_probe+0x1dd/0x330
pci_device_probe+0xd2/0x150
really_probe+0xee/0x280
driver_probe_device+0x50/0xc0
bus_for_each_drv+0x84/0xd0
__device_attach+0xe4/0x150
pci_bus_add_device+0x4e/0x70
pci_bus_add_devices+0x2e/0x66
pci_bus_add_devices+0x59/0x66
pci_bus_add_devices+0x59/0x66
enable_slot+0x344/0x450
acpiphp_check_bridge.part.0+0x119/0x150
acpiphp_hotplug_notify+0xaa/0x140
acpi_device_hotplug+0xa2/0x3f0
acpi_hotplug_work_fn+0x1a/0x30
process_one_work+0x234/0x580
worker_thread+0x50/0x3b0
kthread+0x10a/0x140
ret_from_fork+0x3a/0x50
-> #0 (pci_rescan_remove_lock){+.+.}:
__lock_acquire+0xe54/0x1ac0
lock_acquire+0xb8/0x1b0
__mutex_lock+0xac/0x9a0
authorized_store+0xe8/0x210
kernfs_fop_write+0x125/0x1b0
vfs_write+0xc2/0x1d0
ksys_write+0x6c/0xf0
do_syscall_64+0x50/0x180
entry_SYSCALL_64_after_hwframe+0x49/0xbe
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&tb->lock);
lock(pci_rescan_remove_lock);
lock(&tb->lock);
lock(pci_rescan_remove_lock);
*** DEADLOCK ***
5 locks held by pool-/usr/lib/b/1258:
#0: 000000003df1a1ad (&f->f_pos_lock){+.+.}, at: __fdget_pos+0x4d/0x60
#1: 0000000095a40b02 (sb_writers#6){.+.+}, at: vfs_write+0x185/0x1d0
#2: 0000000017a7d714 (&of->mutex){+.+.}, at: kernfs_fop_write+0xf2/0x1b0
#3: 000000004f262981 (kn->count#208){.+.+}, at: kernfs_fop_write+0xfa/0x1b0
#4: 00000000bfb796b5 (&tb->lock){+.+.}, at: authorized_store+0x7c/0x210
stack backtrace:
CPU: 0 PID: 1258 Comm: pool-/usr/lib/b Tainted: G T 5.3.0-rc6+ #1
On an system using ACPI hotplug the host router gets hotplugged first and then
the firmware starts sending notifications about connected devices so the above
scenario should not happen in reality. However, after taking a second
look at commit a03e828915 ("thunderbolt: Serialize PCIe tunnel
creation with PCI rescan") that introduced the locking, I don't think it
is actually correct. It may have cured the symptom but probably the real
root cause was somewhere closer to PCI stack and possibly is already
fixed with recent kernels. I also tried to reproduce the original issue
with the commit reverted but could not.
So to keep lockdep happy and the code bit less complex drop calls to
pci_lock_rescan_remove()/pci_unlock_rescan_remove() in
tb_switch_set_authorized() effectively reverting a03e828915.
Link: https://lkml.org/lkml/2019/8/30/513
Fixes: a03e828915 ("thunderbolt: Serialize PCIe tunnel creation with PCI rescan")
Reported-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When we discover existing DP tunnels the code checks whether DP IN
adapter port is enabled by calling tb_dp_port_is_enabled() before it
continues the discovery process. On Light Ridge (gen 1) controller
reading only the first dword of the DP IN config space causes subsequent
access to the same DP IN port path config space to fail or return
invalid data as can be seen in the below splat:
thunderbolt 0000:07:00.0: CFG_ERROR(0:d): Invalid config space or offset
Call Trace:
tb_cfg_read+0xb9/0xd0
__tb_path_deactivate_hop+0x98/0x210
tb_path_activate+0x228/0x7d0
tb_tunnel_restart+0x95/0x200
tb_handle_hotplug+0x30e/0x630
process_one_work+0x1b4/0x340
worker_thread+0x44/0x3d0
kthread+0xeb/0x120
? process_one_work+0x340/0x340
? kthread_park+0xa0/0xa0
ret_from_fork+0x1f/0x30
If both DP In adapter config dwords are read in one go the issue does
not reproduce. This is likely firmware bug but we can work it around by
always reading the two dwords in one go. There should be no harm for
other controllers either so can do it unconditionally.
Link: https://lkml.org/lkml/2019/8/28/160
Reported-by: Brad Campbell <lists2009@fnarfbargle.com>
Tested-by: Brad Campbell <lists2009@fnarfbargle.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The Thunderbolt controller is integrated into the Ice Lake CPU itself
and requires special flows to power it on and off using force power bit
in NHI VSEC registers. Runtime PM (RTD3) and Sx flows also differ from
the discrete solutions. Now the firmware notifies the driver whether
RTD3 entry or exit are possible. The driver is responsible of sending
Go2Sx command through link controller mailbox when system enters Sx
states (suspend-to-mem/disk). Rest of the ICM firwmare flows follow
Titan Ridge.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
Ice Lake Thunderbolt controller NVM firmware is part of the BIOS image
which means it is not writable through the DMA port anymore. However, we
can still read it so we can keep nvm_version and active parts of NVM.
This way users still can find out the active NVM version and other
potentially useful information directly from Linux.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
Thunderbolt host routers may not always contain DROM that includes
device identification information. This is mostly needed for Ice Lake
systems but some Falcon Ridge controllers on PCs also do not have DROM.
In that case hide the identification attributes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
There are two ways to mark a port as unimplemented. Typical way is to
return port type as TB_TYPE_INACTIVE when its config space is read.
Alternatively if the port is not physically present (such as ports 10
and 11 in ICL) reading from port config space returns
TB_CFG_ERROR_INVALID_CONFIG_SPACE instead. Currently the driver bails
out from adding the switch if it receives any error during port
inititialization which is wrong.
Handle this properly and just leave the port as TB_TYPE_INACTIVE before
continuing to the next port.
This also allows us to get rid of special casing for Light Ridge port 5
in eeprom.c.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups. Because of this, there is going
to be some merge issues with your tree at the moment, I'll follow up
with the expected resolutions to make it easier for you.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups (will cause build warnings
with s390 and coresight drivers in your tree)
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse
easier due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of merge
issues that Stephen has been patient with me for. Other than the merge
issues, functionality is working properly in linux-next :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXSgpnQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykcwgCfS30OR4JmwZydWGJ7zK/cHqk+KjsAnjOxjC1K
LpRyb3zX29oChFaZkc5a
=XrEZ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and debugfs updates from Greg KH:
"Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse easier
due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of
merge issues that Stephen has been patient with me for"
* tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (102 commits)
debugfs: make error message a bit more verbose
orangefs: fix build warning from debugfs cleanup patch
ubifs: fix build warning after debugfs cleanup patch
driver: core: Allow subsystems to continue deferring probe
drivers: base: cacheinfo: Ensure cpu hotplug work is done before Intel RDT
arch_topology: Remove error messages on out-of-memory conditions
lib: notifier-error-inject: no need to check return value of debugfs_create functions
swiotlb: no need to check return value of debugfs_create functions
ceph: no need to check return value of debugfs_create functions
sunrpc: no need to check return value of debugfs_create functions
ubifs: no need to check return value of debugfs_create functions
orangefs: no need to check return value of debugfs_create functions
nfsd: no need to check return value of debugfs_create functions
lib: 842: no need to check return value of debugfs_create functions
debugfs: provide pr_fmt() macro
debugfs: log errors when something goes wrong
drivers: s390/cio: Fix compilation warning about const qualifiers
drivers: Add generic helper to match by of_node
driver_find_device: Unify the match function with class_find_device()
bus_find_device: Unify the match callback with class_find_device
...
There is an arbitrary difference between the prototypes of
bus_find_device() and class_find_device() preventing their callers
from passing the same pair of data and match() arguments to both of
them, which is the const qualifier used in the prototype of
class_find_device(). If that qualifier is also used in the
bus_find_device() prototype, it will be possible to pass the same
match() callback function to both bus_find_device() and
class_find_device(), which will allow some optimizations to be made in
order to avoid code duplication going forward. Also with that, constify
the "data" parameter as it is passed as a const to the match function.
For this reason, change the prototype of bus_find_device() to match
the prototype of class_find_device() and adjust its callers to use the
const qualifier in accordance with the new prototype of it.
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Kershner <david.kershner@unisys.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: David Airlie <airlied@linux.ie>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Harald Freudenberger <freude@linux.ibm.com>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Peter Oberparleiter <oberpar@linux.ibm.com>
Cc: Sebastian Ott <sebott@linux.ibm.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Cc: rafael@kernel.org
Acked-by: Corey Minyard <minyard@acm.org>
Acked-by: David Kershner <david.kershner@unisys.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de> # for the I2C parts
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a device is authorized from userspace by writing to authorized
attribute we first take the domain lock and then runtime resume the
device in question. There are two issues with this.
First is that the device connected notifications are blocked during this
time which means we get them only after the authorization operation is
complete. Because of this the authorization needed flag from the
firmware notification is not reflecting the real authorization status
anymore. So what happens is that the "authorized" keeps returning 0 even
if the device was already authorized properly.
Second issue is that each time the controller is runtime resumed the
connection_id field of device connected notification may be different
than in the previous resume. We need to use the latest connection_id
otherwise the firmware rejects the authorization command.
Fix these by moving runtime resume operations to happen before the
domain lock is taken, and waiting for the updated device connected
notification from the firmware before we allow runtime resume of a
device to complete.
While there add missing locking to tb_switch_nvm_read().
Fixes: 09f11b6c99 ("thunderbolt: Take domain lock in switch sysfs attribute callbacks")
Reported-by: Pengfei Xu <pengfei.xu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Now that the driver can handle every possible tunnel types there is no
point to log everything as info level so turn these to happen at debug
level instead.
While at it remove duplicated tunnel activation log message
(tb_tunnel_activate() calls tb_tunnel_restart() which print the same
message) and add one missing '\n' termination.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Two domains (hosts) can be connected through a Thunderbolt cable and in
that case they can start software services such as networking over the
high-speed DMA paths. Now that we have all the basic building blocks in
place to create DMA tunnels over the Thunderbolt fabric we can add this
support to the software connection manager as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In order to detect possible connections to other domains we need to be
able to find out why tb_switch_alloc() fails so make it return ERR_PTR()
instead. This allows the caller to differentiate between errors such as
-ENOMEM which comes from the kernel and for instance -EIO which comes
from the hardware when trying to access the possible switch.
Convert all the current call sites to handle this properly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In addition to PCIe and Display Port tunnels it is also possible to
create tunnels that forward DMA traffic from the host interface adapter
(NHI) to a NULL port that is connected to another domain through a
Thunderbolt cable. These tunnels can be used to carry software messages
such as networking packets.
To support this we introduce another tunnel type (TB_TUNNEL_DMA) that
supports paths from NHI to NULL port and back.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Display Port tunnels are somewhat more complex than PCIe tunnels as it
requires 3 tunnels (AUX Rx/Tx and Video). In addition we are not
supposed to create the tunnels immediately when a DP OUT is enumerated.
Instead we need to wait until we get hotplug event to that adapter port
or check if the port has HPD set before tunnels can be established. This
adds Display Port tunneling support to the software connection manager.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
NFC (non flow control) credits is actually 20-bit field so update
tb_port_add_nfc_credits() to handle this properly. This allows us to set
NFC credits for Display Port path in subsequent patches.
Also make sure the function does not update the hardware if the
underlying switch is already unplugged.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We will be needing these routines to find Display Port adapters as well
so modify them to take port type as the second parameter.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In Apple Macs the boot firmware (EFI) connects all devices automatically
when the system is started, before it hands over to the OS. Instead of
ignoring we discover all those PCIe tunnels and record them using our
internal structures, just like we do when a device is connected after
the OS is already up.
By doing this we can properly tear down tunnels when devices are
disconnected. Also this allows us to resume the existing tunnels after
system suspend/resume cycle.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We need to be able to walk from one port to another when we are creating
paths where there are multiple switches between two ports. For this
reason introduce a new function tb_next_port_on_path().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Currently the driver only assigns remote port for the primary port if in
case of dual link. This makes things such as walking from one port to
another more complex than necessary because the code needs to change
from secondary to primary port if the path that is established is
created using secondary links.
In order to always assign both remote pointers we need to prevent the
scanning code from following the secondary link. Failing to do that
might cause problems as the same switch may be enumerated twice (or
removed in case of unplug). Handle that properly by introducing a new
function tb_port_has_remote() that returns true only for the primary
port. We also update tb_is_upstream_port() to support both dual link
ports, make it take const port pointer and move it below
tb_upstream_port() to keep similar functions close.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Each port has a separate path configuration space that is used for
finding the next hop (switch) in the path. HopID is an index to this
configuration space. HopIDs 0 - 7 are reserved by the protocol.
In order to get next available HopID for each direction we provide two
pairs of helper functions that can be used to allocate and release
HopIDs for a given port.
While there remove obsolete TODO comment.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
To be able to tunnel non-PCIe traffic, separate tunnel functionality
into generic and PCIe specific parts. Rename struct tb_pci_tunnel to
tb_tunnel, and make it hold an array of paths instead of just two.
Update all the tunneling functions to take this structure as parameter.
We also move tb_pci_port_active() to switch.c (and rename it) where we
will be keeping all port and switch related functions.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The adapter specific capability either is there or not if the port does
not hold an adapter. Instead of always finding it on-demand we read the
offset just once when the port is initialized.
While there we update the struct port documentation to follow kernel-doc
format.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Thunderbolt 2 devices and beyond link controller needs to be notified
when a switch is going to be suspended by setting bit 31 in LC_SX_CTRL
register. Add this functionality to the software connection manager.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Thunderbolt 2 devices and beyond need to have additional bits set in
link controller specific registers. This includes two bits in LC_SX_CTRL
that tell the link controller which lane is connected and whether it is
upstream facing or not.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We will be adding more link controller functionality in subsequent
patches and it does not make sense to keep all that in switch.c, so
separate LC functionality into its own file.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Maximum depth in Thunderbolt topology is 6 so make sure it is not
possible to allocate switches that exceed the depth limit.
While at it update tb_switch_alloc() to use upper/lower_32_bits()
following tb_switch_alloc_safe_mode().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
switch_lock was introduced because it allowed serialization of device
authorization requests from userspace without need to take the big
domain lock (tb->lock). This was fine because device authorization with
ICM is just one command that is sent to the firmware. Now that we start
to handle all tunneling in the driver switch_lock is not enough because
we need to walk over the topology to establish paths.
For this reason drop switch_lock from the driver completely in favour of
big domain lock.
There is one complication, though. If userspace is waiting for the lock
in tb_switch_set_authorized(), it keeps the device_del() from removing
the sysfs attribute because it waits for active users to release the
attribute first which leads into following splat:
INFO: task kworker/u8:3:73 blocked for more than 61 seconds.
Tainted: G W 5.1.0-rc1+ #244
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
kworker/u8:3 D12976 73 2 0x80000000
Workqueue: thunderbolt0 tb_handle_hotplug [thunderbolt]
Call Trace:
? __schedule+0x2e5/0x740
? _raw_spin_lock_irqsave+0x12/0x40
? prepare_to_wait_event+0xc5/0x160
schedule+0x2d/0x80
__kernfs_remove.part.17+0x183/0x1f0
? finish_wait+0x80/0x80
kernfs_remove_by_name_ns+0x4a/0x90
remove_files.isra.1+0x2b/0x60
sysfs_remove_group+0x38/0x80
sysfs_remove_groups+0x24/0x40
device_remove_attrs+0x3d/0x70
device_del+0x14c/0x360
device_unregister+0x15/0x50
tb_switch_remove+0x9e/0x1d0 [thunderbolt]
tb_handle_hotplug+0x119/0x5a0 [thunderbolt]
? process_one_work+0x1b7/0x420
process_one_work+0x1b7/0x420
worker_thread+0x37/0x380
? _raw_spin_unlock_irqrestore+0xf/0x30
? process_one_work+0x420/0x420
kthread+0x118/0x130
? kthread_create_on_node+0x60/0x60
ret_from_fork+0x35/0x40
We deal this by following what network stack did for some of their
attributes and use mutex_trylock() with restart_syscall(). This makes
userspace release the attribute allowing sysfs attribute removal to
progress before the write is restarted and eventually fail when the
attribute is removed.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
tb_switch_find_by_route() does the same already so use it instead and
remove duplicated get_switch_at_route().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Memory allocated via kmemdup might fail and return a NULL pointer.
This patch adds a check on the return value of kmemdup and passes the
error upstream.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
During NVM upgrade process the host router is hot-removed for a short
while. During this time it is possible that the root port is moved into
D3cold which would be fine if the root port could trigger PME on itself.
However, many systems actually do not implement it so what happens is
that the root port goes into D3cold and never wakes up unless userspace
does PCI config space access, such as running 'lscpi'.
For this reason we explicitly prevent the root port from runtime
suspending during NVM upgrade.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel has done pretty major changes to the driver and we continue to do
so in the future as well. Add Intel as copyright holder of the files we
have done changes.
While there drop "Cactus Ridge" from the headers because this driver
works also with other Thunderbolt controllers.
No functional changes intended.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <yehezkelshb@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The previous patch made the driver less verbose meanining that all the
switch structures and ports are now logged as debug level. However, we
have been missing similar output that USB for intance prints when a new
USB device is connected and disconnected. This information is useful for
end users as well as developers because it immediately shows the actual
device that was connected.
This patch adds printing of the actual connected devices to the driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <yehezkelshb@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the driver logs quite a lot to the system message buffer even
when doing normal operations. This information is not useful for
ordinary users and might even annoy some.
For this reason convert most of the logs at info level to happen at
debug level instead. The nice output formatting is untouched.
Logging can be easily re-enabled by passing "thunderbolt.dyndbg" in the
kernel command line (or using the corresponding control file runtime).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <yehezkelshb@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When Thunderbolt host controller is set to RTD3 mode (Runtime D3) it is
present all the time. Because of this it is important to runtime suspend
the controller whenever possible. In case of ICM we have following rules
which all needs to be true before the host controller can be put to D3:
- The controller firmware reports to support RTD3
- All the connected devices announce support for RTD3
- There is no active XDomain connection
Implement this using standard Linux runtime PM APIs so that when all the
children devices are runtime suspended, the Thunderbolt host controller
PCI device is runtime suspended as well. The ICM firmware then starts
powering down power domains towards RTD3 but it can prevent this if it
detects that there is an active Display Port stream (this is not visible
to the software, though).
The Thunderbolt host controller will be runtime resumed either when
there is a remote wake event (device is connected or disconnected), or
when there is access from userspace that requires hardware access.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Titan Ridge is the next Thunderbolt 3 controller. The ICM firmware
message format in Titan Ridge differs from Falcon Ridge and Alpine Ridge
somewhat because it is using route strings addressing devices. In
addition to that the DMA port of 4-channel (two port) controller is in
different port number than the previous controllers. There are some
other minor differences as well.
This patch add support for Intel Titan Ridge and the new ICM firmware
message format.
Signed-off-by: Radion Mirchevsky <radion.mirchevsky@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
In various cases, Thunderbolt device can be connected by ICM on boot
without waiting for approval from user. Most cases are related to
OEM-specific BIOS configurations. This information is interesting for
user-space as if the device isn't in SW ACL, it may create a friction in
the user experience where the device is automatically authorized if it's
connected on boot but requires an explicit user action if connected
after OS is up. User-space can use this information to suggest adding
the device to SW ACL for auto-authorization on later connections.
Signed-off-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
With the new ICM messaging there is need for find switch by route string
instead of link and depth. Add new function that makes it possible.
Signed-off-by: Radion Mirchevsky <radion.mirchevsky@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Use correct name in kernel-doc of tb_switch_find_by_uuid().
Signed-off-by: Radion Mirchevsky <radion.mirchevsky@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
We need to make sure a new PCIe tunnel is not created in a middle of
previous PCI rescan because otherwise the rescan code might find too
much and fail to reconfigure devices properly. This is important when
native PCIe hotplug is used. In BIOS assisted hotplug there should be no
such issue.
Fixes: f67cf49117 ("thunderbolt: Add support for Internal Connection Manager (ICM)")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Mika Westerberg