The ethtool statistics are available only when
CONFIG_ATH9K_DEBUGFS is enabled, move these functions
to debug.c
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Petr Stetiar <ynezz@true.cz>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for advertising GreenField, 40MHz intolerance
or LDPC coding support to cfg80211.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: stomp audio profiles on weak signal
strength" failed to take care of new stomp type while
programming concurrent tx priority. That leads to array
index out of bounds access.
drivers/net/wireless/ath/ath9k/btcoex.c:414
ath9k_hw_btcoex_set_concur_txprio()
error: buffer overflow 'stomp_txprio' 4 <= 4
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The LMAC API states that the TSF clock value of
every rx'ed frame is a "usec accurate timestamp
of the hardware clock at the end of frame
(before OFDM SIFS EOF padding)".
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The vendor radiotap patch added a few fields to
struct ieee80211_rx_status that need to be zero,
initialize the struct instead of using whatever
was left on the stack.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The vendor radiotap patch added a few fields to
struct ieee80211_rx_status that need to be zero,
initialize the struct instead of using whatever
was left on the stack.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding __printf helps spot format and argument mismatches.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The frequencies will be printed when actually
doing the scan, and the IEs can be captured
on the hwsim0 monitor.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the number of channels is > 1, which means that
hwsim will use mac80211 channel contexts, it can
also advertise VHT support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Convert mac80211 (and where necessary, some drivers a
little bit) to the new channel definition struct.
This will allow extending mac80211 for VHT, which is
currently restricted to channel contexts since there
are no drivers using that which makes it easier. As
I also don't care about VHT for drivers not using the
channel context API, I won't convert the previous API
to VHT support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change nl80211 to support specifying a VHT (or HT)
using the control channel frequency (as before) and
new attributes for the channel width and first and
second center frequency. The old channel type is of
course still supported for HT.
Also change the cfg80211 channel definition struct
to support these by adding the relevant fields to
it (and removing the _type field.)
This also adds new helper functions:
- cfg80211_chandef_create to create a channel def
struct given the control channel and channel type,
- cfg80211_chandef_identical to check if two channel
definitions are identical
- cfg80211_chandef_compatible to check if the given
channel definitions are compatible, and return the
wider of the two
This isn't entirely complete, but that doesn't matter
until we have a driver using it. In particular, it's
missing
- regulatory checks on the usable bandwidth (if that
even makes sense)
- regulatory TX power (database can't deal with it)
- a proper channel compatibility calculation for the
new channel types
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of passing a channel pointer and channel type
to all functions and driver methods, pass a new channel
definition struct. Right now, this struct contains just
the control channel and channel type, but for VHT this
will change.
Also, add a small inline cfg80211_get_chandef_type() so
that drivers don't need to use the _type field of the
new structure all the time, which will change.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As mwifiex (and mac80211 in the software case) are the
only drivers actually implementing remain-on-channel
with channel type, userspace can't be relying on it.
This is the case, as it's used only for P2P operations
right now.
Rather than adding a flag to tell userspace whether or
not it can actually rely on it, simplify all the code
by removing the ability to use different channel types.
Leave only the validation of the attribute, so that if
we extend it again later (with the needed capability
flag), it can't break userspace sending invalid data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
CC drivers/net/wireless/rtlwifi/rtl8723ae/trx.o
drivers/net/wireless/rtlwifi/rtl8723ae/trx.c: In function ‘rtl8723ae_rx_query_desc’:
drivers/net/wireless/rtlwifi/rtl8723ae/trx.c:324:21: error: ‘RX_FLAG_MACTIME_MPDU’ undeclared (first use in this function)
drivers/net/wireless/rtlwifi/rtl8723ae/trx.c:324:21: note: each undeclared identifier is reported only once for each function it appears in
make[3]: *** [drivers/net/wireless/rtlwifi/rtl8723ae/trx.o] Error 1
Signed-off-by: John W. Linville <linville@tuxdriver.com>
One of the debug macro invocations ended up with a stray 0 argument
where the format string should be. Remove it.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes sparse warning:
drivers/net/wireless/brcm80211/brcmsmac/main.c:308:10: sparse: symbol 'wlc_prio2prec_map' was not declared. Should it be static?
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'stations' debugfs file has multiple issues. It doesn't scale
to an arbitrary number of associated stations and allocating
64K is not elegant either. Now that changes have been made in
mac80211 to support dynamic creation/deletion of driver-specific
debugfs files on station addition/removal, remove this file and
make use of the mac80211 hooks (which will be done in a sebsequent
patch).
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the rate statistics only when debugfs has been enabled
in ath9k and mac80211 and move the stat() functions under proper
conditionals.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the rate control statistics debugfs file properly
via remove_sta_debugfs(). Also, check for both MAC80211_DEBUGFS
and ATH9K_DEBUGFS config options.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'xmit' debugfs file has become big and unwieldy, fix
multiple issues with its usage:
* Store TX counters/statistics only for the 4 Access Categories.
Use IEEE80211_NUM_ACS instead of ATH9K_NUM_TX_QUEUES.
* Move various utility macros to debug.h, they can be reused
elsewhere.
* Remove tx_complete_poll_work_seen.
* Remove code that accesses various internal queue-specific
variables without any locking whatsoever. HW/SW queue details
will be handled in a subsequent patch.
* Do not print internal values like txq_headidx and txq_headidx.
They were mostly unused anyway, considering code like:
PRX("txq_tailidx: ", txq_headidx);
* Handle 'txprocdesc' for EDMA too.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the macros provided by mac80211 and remove redundant
declarations inside the drivers.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move regulatory domain initialization code to a separate function.
Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On lower WLAN signal strength, WLAN downlink traffic might suffer
from retransmissions. At the mean time, playing SCO/A2DP profiles
is affecting WLAN stability. In such scenario, by stomping SCO/A2DP
BT traffic completely for a BTCOEX period, gives WLAN traffic an
oppertunity to recover PHY rate. It also improves WLAN stability at
lower RSSI without sacificing BT traffic.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch reverts the commit "ath9k_hw: Wait BT calibration to complete"
and bail out from MCI interrupt routine for chip reset. The above commit
stalls the WLAN TCP traffic while bringing up and down the BT interface
iteratively. Fixing this properly by queueing up chip reset and bailing
out properly from tasklet routine.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
FATAL and WATCHDOG interrupts should be processed first followed
by others.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This avoids build failures on some architectures...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
These messages clutter up the trace buffer without adding any useful
information.
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the brcmsmac_tx trace system for tx debugging. Existing code to dump
tx status and descriptors are converted to using tracepoints, allowing
for more efficient collection and post-processing of this data. These
tracepoints are placed to collect data for all tx frames instead of only
on errors. Logging of tx errors is also improved.
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also convert relevant messages to use this macro.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also convert relevant messages to use this macro.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also convert relevant message to use this macro.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also convert relevant messages over to use thses macros.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This macro is used for messages related to the 802.11 MAC layer.
Relevant messages are also converted to use this macro.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert most uses of wiphy_* and pr_* for general error and debug
messages to use the internal debug macros instead. Most code used only
for initialization still use wiphy_err(), as well as some locations
which are executed too early to use the debug macros. Some debug
messages which are redundant or not useful are removed.
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new brcmsmac_msg trace system to enable writing of debug messages
to the trace buffer, and add brcms_* macros for storing device debug
messages in the trace buffer in addition to the printk log buffer.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The debug level can be set by passing debug=... to brcmsmac whenever
CONFIG_BRCMDBG is enabled.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In preparation for enhancements to debug and trace support, convert the
message levels to debug levels which will be used for enabling
categories of debug messages. The two message levels are little-used
anyway and are combined into the BRCM_DL_INFO debug level.
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the runtime overhead of trace support is small when tracing is
disabled, users may be interested in turning on trace support while
leaving other debug features off. Add a new config option named
CONFIG_BRCM_TRACING for this purpose.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently up to 256 frames can be queued for each DMA ring. This is
excessive, and now that we have better flow control we can get by with
less. Experimentation has shown 64 to work well.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan