'hid_hw_stop()' is already in the error handling path when branching to
the 'hid_hw_open_fail' label.
There is no point in calling it twice, so remove one.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Newer Logitech mice report their battery voltage through feature 0x1001
instead of the battery levels through feature 0x1000.
When the device is brought up and we try to query the battery, figure
out if it supports the old or the new feature. If it supports the new
feature, record the feature index and read the battery voltage and
its charge status. The device will respond with three bytes: the first
two are its voltage, and the last one is a bitset, reporting if the
battery is charging, fast or slow, in critical level or discharging.
If everything went correctly, record the fact that we're capable
of querying battery voltage.
Note that the protocol only gives us the current voltage in mV.
We store that as-is, but when queried, we report it in uV as
expected by sysfs.
Like we do for other ways of interacting with the battery for other
devices, refresh the battery status and notify the power supply
subsystem of the changes in voltage and status.
Since there are no known devices which implement both the old and the
new battery feature, we make sure to try the newer feature first and
only fall back to the old one if that fails.
Signed-off-by: Pedro Vanzella <pedro@pedrovanzella.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
This patch adds support for the Logitech MX Master 3 Mouse using the
Logitech Unifying Receiver and Bluetooth LE.
Signed-off-by: Adrian Freund <adrian@freund.io>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
This patch allows hidpp_report_is_connect_event to support
WirelessDeviceStatus connect events.
The WirelessDeviceStatus feature index is stored in hidpp_device when
probed. The connect event's fap feature_index is compared against it if the
device supports it.
Signed-off-by: Mazin Rezk <mnrzk@protonmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
This patch allows short reports to be translated into long reports.
hidpp_validate_device now returns a u8 instead of a bool which represents
the supported reports. The corresponding bits (i.e.
HIDPP_REPORT_*_SUPPORTED) are set if an HID++ report is supported.
If a short report is being sent and the device does not support it, it is
instead sent as a long report.
This patch also introduces support for the MX Master (b01e and b012).
Signed-off-by: Mazin Rezk <mnrzk@protonmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
My Logitech M185 (PID:4038) 2.4 GHz wireless HID++ mouse is causing
intermittent errors like these in the log:
[11091.034857] logitech-hidpp-device 0003:046D:4038.0006: hidpp20_batterylevel_get_battery_capacity: received protocol error 0x09
[12388.031260] logitech-hidpp-device 0003:046D:4038.0006: hidpp20_batterylevel_get_battery_capacity: received protocol error 0x09
[16613.718543] logitech-hidpp-device 0003:046D:4038.0006: hidpp20_batterylevel_get_battery_capacity: received protocol error 0x09
[23529.938728] logitech-hidpp-device 0003:046D:4038.0006: hidpp20_batterylevel_get_battery_capacity: received protocol error 0x09
We are already silencing error-code 0x09 (HIDPP_ERROR_RESOURCE_ERROR)
errors in other places, lets do the same in
hidpp20_batterylevel_get_battery_capacity to remove these harmless,
but scary looking errors from the dmesg output.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
All of the FF-related resources belong to corresponding FF device, so
they should be freed as a part of hidpp_ff_destroy() to avoid
potential race condidions.
Fixes: ff21a635dd ("HID: logitech-hidpp: Force feedback support for the Logitech G920")
Suggested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: Henrik Rydberg <rydberg@bitmath.org>
Cc: Pierre-Loup A. Griffais <pgriffais@valvesoftware.com>
Cc: Austin Palmer <austinp@valvesoftware.com>
Cc: linux-input@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org # 5.2+
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
G920 device only advertises REPORT_ID_HIDPP_LONG and
REPORT_ID_HIDPP_VERY_LONG in its HID report descriptor, so querying
for REPORT_ID_HIDPP_SHORT with optional=false will always fail and
prevent G920 to be recognized as a valid HID++ device.
To fix this and improve some other aspects, modify
hidpp_validate_device() as follows:
- Inline the code of hidpp_validate_report() to simplify
distingushing between non-present and invalid report descriptors
- Drop the check for id >= HID_MAX_IDS || id < 0 since all of our
IDs are static and known to satisfy that at compile time
- Change the algorithms to check all possible report
types (including very long report) and deem the device as a valid
HID++ device if it supports at least one
- Treat invalid report length as a hard stop for the validation
algorithm, meaning that if any of the supported reports has
invalid length we assume the worst and treat the device as a
generic HID device.
- Fold initialization of hidpp->very_long_report_length into
hidpp_validate_device() since it already fetches very long report
length and validates its value
Fixes: fe3ee1ec00 ("HID: logitech-hidpp: allow non HID++ devices to be handled by this module")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204191
Reported-by: Sam Bazely <sambazley@fastmail.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: Henrik Rydberg <rydberg@bitmath.org>
Cc: Pierre-Loup A. Griffais <pgriffais@valvesoftware.com>
Cc: Austin Palmer <austinp@valvesoftware.com>
Cc: linux-input@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org # 5.2+
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
The syzbot fuzzer found a slab-out-of-bounds write bug in the hid-gaff
driver. The problem is caused by the driver's assumption that the
device must have an input report. While this will be true for all
normal HID input devices, a suitably malicious device can violate the
assumption.
The same assumption is present in over a dozen other HID drivers.
This patch fixes them by checking that the list of hid_inputs for the
hid_device is nonempty before allowing it to be used.
Reported-and-tested-by: syzbot+403741a091bf41d4ae79@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
The G700 suffers from the same issue than the G502:
when plugging it in, the driver tries to contact it but it fails.
This timeout is problematic as it introduce a delay in the boot,
and having only the mouse event node means that the hardware
macros keys can not be relayed to the userspace.
Link: https://github.com/libratbag/libratbag/issues/797
Fixes: 91cf9a98ae ("HID: logitech-hidpp: make .probe usbhid capable")
Cc: stable@vger.kernel.org # v5.2
Reviewed-by: Filipe Laíns <lains@archlinux.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
This partially reverts commit 27fc32fd94.
It turns out that the G502 has some issues with hid-logitech-hidpp:
when plugging it in, the driver tries to contact it but it fails.
So the driver bails out leaving only the mouse event node available.
This timeout is problematic as it introduce a delay in the boot,
and having only the mouse event node means that the hardware
macros keys can not be relayed to the userspace.
Filipe and I just gave a shot at the following devices:
G403 Wireless (0xC082)
G703 (0xC087)
G703 Hero (0xC090)
G903 (0xC086)
G903 Hero (0xC091)
G Pro (0xC088)
Reverting the devices we are not sure that works flawlessly.
Reviewed-by: Filipe Laíns <lains@archlinux.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Pull HID fixes from Jiri Kosina:
- regression fixes (reverts) for module loading changes that turned out
to be incompatible with some userspace, from Benjamin Tissoires
- regression fix for special Logitech unifiying receiver 0xc52f, from
Hans de Goede
- a few device ID additions to logitech driver, from Hans de Goede
- fix for Bluetooth support on 2nd-gen Wacom Intuos Pro, from Jason
Gerecke
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: logitech-dj: Fix 064d:c52f receiver support
Revert "HID: core: Call request_module before doing device_add"
Revert "HID: core: Do not call request_module() in async context"
Revert "HID: Increase maximum report size allowed by hid_field_extract()"
HID: a4tech: fix horizontal scrolling
HID: hyperv: Add a module description line
HID: logitech-hidpp: Add support for the S510 remote control
HID: multitouch: handle faulty Elo touch device
HID: wacom: Sync INTUOSP2_BT touch state after each frame if necessary
HID: wacom: Correct button numbering 2nd-gen Intuos Pro over Bluetooth
HID: wacom: Send BTN_TOUCH in response to INTUOSP2_BT eraser contact
HID: wacom: Don't report anything prior to the tool entering range
HID: wacom: Don't set tool type until we're in range
HID: rmi: Use SET_REPORT request on control endpoint for Acer Switch 3 and 5
HID: logitech-hidpp: add support for the MX5500 keyboard
HID: logitech-dj: add support for the Logitech MX5500's Bluetooth Mini-Receiver
HID: i2c-hid: add iBall Aer3 to descriptor override
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 315 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190115.503150771@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The S510 remote-control shows up as a second keyboard (keypad) on the
receiver. It has a scroll-wheel, which normally sends wheel event
originating from the mouse's evdev node.
Add a HIDPP_QUIRK_KBD_SCROLL_WHEEL quirk for it, so that the wheel events
properly originate from the evdev node of the remote control itself.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Don't populate the array consumer_rdesc_start on the stack but instead
make it static. Makes the object code smaller by 88 bytes.
Before:
text data bss dec hex filename
59155 9840 448 69443 10f43 drivers/hid/hid-logitech-hidpp.o
After:
text data bss dec hex filename
59003 9904 448 69355 10eeb drivers/hid/hid-logitech-hidpp.o
(gcc version 8.3.0, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The MX5500 keyboard needs the HIDPP_CONSUMER_VENDOR_KEYS quirk to report
events for the 'A' - 'D' Smart Keys and for the "Photo Gallery" and
"Gadgets" keys.
In addition to this adding the Bluetooth match, so that hid-logitech-hidpp
is used instead of the generic HID driver, also adds battery monitoring
support when the keyboard is connected over Bluetooth.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
All Logitech 27 MHz keyboards and also the MX5000 bluetooth keyboard use
Logitech custom usages of 0x10xx in the consumer page. The descriptor for
the consumer input-report only declares usages up to 652, so we end up
dropping all the input-reports reporting 0x10xx usages without reporting
events for these to userspace.
This commit adds a descriptor_fixup function for this which changes the
usage and logical maximum to 0x107f. Mapping these usages to something
other then KEY_UNKNOWN is left to userspace (hwdb). Note:
1. The old descriptor_fixup for this in hid-lg.c used a maximimum of 0x104d
this is not high enough, the S520 keyboard battery key sends 0x106f.
2. The descriptor_fixup is flexible so that it works with both the kbd-
desc. passed by the logitech-dj code and with bluetooth descriptors.
The descriptor_fixup makes most keys work on 27 MHz keyboards, but it is
not enough to get all keys to work on 27 MHz keyboards and just the fixup
is not enough to get the MX5000 to generate 0x10xx events:
1) The LX501 and MX3000 27 MHz kbds both have a button labelled "media"
(called "Media Player" by SetPoint) and a button with a remote-control
symbol ("Media Life" in SetPoint) which both send an identical consumer
usage-page code (0x0183) making the 2 buttons indistinguishable,
switching to HID++ 1.0 consumer keys reports makes the remote-control
symbol button generate a 0x10xx Logitech specific code instead.
2) The MX5000 Bluetooth keyboard has 11 keys which report 0x10xx consumer
page usages, but unlike 27 MHz devices which happily send 0x10xx codes in
their normal consumer-page input-report, the MX5000 honors the maximum of
652 from its descriptor and sends a 0x0000 code (so release) whenever these
keys are pressed. When switching to HID++ sub-id 0x03 HID++ 1.0 consumer
keys reports these 0x10xx codes do get properly reported.
This commit adds support for HID++ 1.0 consumer keys reports and enables
this for all 27 MHz keyboards and for the MX5000.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Some mice have extra buttons which are only reported through HID++ 1.0
extra mouse buttons reports, this commit adds support for this and
automatically enables this support for all 27 MHz mice.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Add a quirk for switching wheel event reporting to using the HID++
report for this.
This has 2 advantages:
1) Without this tilting the scrollwheel left / right will send a
scroll-lock + cursor-left/-right + scroll-lock key-sequence instead of
hwheel events
2) The HID++ reports contain the device index instead of using the generic
HID implementation, so this will make scroll-wheel events from the wheel
on some keyboards be emitted by the right event node.
2. also fixes keyboard scroll-wheel events getting lost in the (mostly
theoretical) case of there not being a mouse paired with the receiver.
This commit enables this quirk for all 27Mhz mice, it cannot hurt to have
it enabled and this avoids the need to keep adding more and more quirks for
this. This has been tested in 5 different 27MHz mice, 3 of which have a
wheel which can tilt.
This commit also adds explicit quirks for 3 keyboards with a zoom-/scroll-
wheel. The MX3000 keyboard scroll-wheel can also tilt. I've defined aliases
to the new HIDPP_QUIRK_HIDPP_WHEELS for this, so that it is clear why the
keyboard has the quirk and in case we want to handle the keyboard wheels
and especially the keyboard zoom-wheels differently in the future.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Make hidpp10_set_register_bit() take a mask and value for the register
byte being changed, rather then making it only set a single bit.
While at it also at defines for the bits which we will be using.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Most device-class specific code needs access to the input_device, instead
of storing that in the class specific data-struct, simply store this into
the hidpp_device struct itself.
In case of the m560 this avoids the need for having private data at all
and this will also avoid the need to add private data in some upcoming
patches.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
The HID++ spec says the following about the very long report length:
"n Bytes, depends on HID++ collection declaration".
Hardcoding this breaks talking to some HID++ devices over BlueTooth, since
they declare only 45 bytes data for the very long report, rather then the
hardcoded 63.
This commit fixes this by getting the actual report length from the
descriptors.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Logitech 27MHz devices are HID++ devices, so handle them in the hidpp
driver, this enables battery monitoring on these devices (and more in
follow-up patches).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
According to the logitech_hidpp_2.0_specification_draft_2012-06-04.pdf doc:
https://lekensteyn.nl/files/logitech/logitech_hidpp_2.0_specification_draft_2012-06-04.pdf
We should use a register-access-protocol request using the short input /
output report ids. This is necessary because 27MHz HID++ receivers have
a max-packetsize on their HIP++ endpoint of 8, so they cannot support
long reports. Using a feature-access-protocol request (which is always
long or very-long) with these will cause a timeout error, followed by
the hidpp driver treating the device as not being HID++ capable.
This commit fixes this by switching to using a rap request to get the
protocol version.
Besides being tested with a (046d:c517) 27MHz receiver with various
27MHz keyboards and mice, this has also been tested to not cause
regressions on a non-unifying dual-HID++ nano receiver (046d:c534) with
k270 and m185 HID++-2.0 devices connected and on a unifying/dj receiver
(046d:c52b) with a HID++-2.0 Logitech Rechargeable Touchpad T650.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
All the various populate_input functions have an origin_is_hid_core
function parameter, but none use it, remove it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
The hidpp variable is already initialized with hid_get_drvdata(hdev)
when it is declared, drop the second no-op assignment.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
With devices attached to a non-unifying 2.4GHz receiver we sometimes fail
to get the name. This is not a fatal error, we can just continue with the
original name.
So instead of bailing out, continue with battery-initialization when this
happens. This fixes the battery not getting registered when we fail to
get the name.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Some devices report an empty or very short name, in this case stick
with the name generated by the logitech-dj code instead of overriding it
with e.g. "Logitech ".
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
The current custom solution for the G920 is not the best because
hid_hw_start() is not called at the end of the .probe().
It means that any configuration retrieved after the initial hid_hw_start
would not be exposed to user space without races.
We can simply force hid_hw_start to just enable the transport layer by
not using a connect_mask. This way, we can have a common path between
USB, Unifying and Bluetooth devices.
With this change, we can now support the non DJ receivers for low end
devices, which will allow us to fetch the actual names of the paired
device (instead of 'Logitech Wireless Receiver')
Tested with a M185 with the non unifying receiver, a T650 and many other
unifying devices, and the T651 over Bluetooth.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
On the gaming mice, there are 2 interfaces, one for the mouse and one
for the macros. Better allow everybody to go through hid-logitech-hidpp
than trying to be smarter.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
There is no need to set drvdata to NULL on probe failure and remove,
the driver-core already does this for us.
[hdegoede@redhat.com: Isolate Logitech changes into a separate patch]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
According to hidpp20_batterylevel_get_battery_info my Logitech K270
keyboard reports only 2 battery levels. This matches with what I've seen
after testing with batteries at varying level of fullness, it always
reports either 5% or 30%.
Windows reports "battery good" for the 30% level. I've captured an USB
trace of Windows reading the battery and it is getting the same info
as the Linux hidpp code gets.
Now that Linux handles these devices as hidpp devices, it reports the
battery as being low as it treats anything under 31% as low, this leads
to the user constantly getting a "Keyboard battery is low" warning from
GNOME3, which is very annoying.
This commit fixes this by changing the low threshold to anything under
30%, which I assume is what Windows does.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Remove the hidpp_is_connected() function wrapper, and have the callers
directly call hidpp_root_get_protocol_version() instead.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Simply always print the HID++ version on hidpp_root_get_protocol_version
success.
This also fixes the version not being printed when a HID++ device
connected through a receiver is already connected when the hidpp driver
is loaded.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hidpp_scroll_counter_handle_scroll() doesn't expect a 0-value scroll event, it
gets interpreted as a negative scroll direction event. This can cause scroll
direction resets and thus broken scrolling.
Fixes: 4435ff2f09 ("HID: logitech: Enable high-resolution scrolling on Logitech mice")
Cc: stable@vger.kernel.org # v5.0
Reported-and-tested-by: Aimo Metsälä <aimetsal@outlook.com>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
create_singlethread_workqueue may fail and return NULL. The fix checks if it is
NULL to avoid NULL pointer dereference. Also, the fix moves the call of
create_singlethread_workqueue earlier to avoid resource-release issues.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Harry Cutts <hcutts@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Verified-by: Harry Cutts <hcutts@chromium.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
There are three features used by various Logitech mice for
high-resolution scrolling: the scrolling acceleration bit in HID++ 1.0,
and the x2120 and x2121 features in HID++ 2.0 and above. This patch
supports all three, and uses the multiplier reported by the mouse for
the HID++ 2.0+ features.
The full list of product IDs of mice which support high-resolution
scrolling was provided by Logitech, but the patch was tested using the
following mice (using the Unifying receiver):
* HID++ 1.0: Anywhere MX, Performance MX
* x2120: M560
* x2121: MX Anywhere 2, MX Master 2S
This patch is a combinations of the now-reverted commits 1ff2e1a44e,
d56ca9855b, 5fe2ccbef9, 044ee89028 together with some extra bits for the
directional and timeout-based reset.
The previous patch series was in hid-input, it appears this remainder
handling is logitech-specific and was moved to hid-logitech-hidpp.c and
renamed accordingly.
Signed-off-by: Harry Cutts <hcutts@chromium.org>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Verified-by: Harry Cutts <hcutts@chromium.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
"Scrolling acceleration" is a bit of a misnomer: it doesn't deal with
acceleration at all. However, that's the name used in Logitech's spec,
so I used it here.
Signed-off-by: Harry Cutts <hcutts@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Verified-by: Harry Cutts <hcutts@chromium.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Verified-by: Harry Cutts <hcutts@chromium.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
This reverts commit 051dc9b057.
It turns out the current API is not that compatible with
some Microsoft mice, so better start again from scratch.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Harry Cutts <hcutts@chromium.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit d56ca9855b.
It turns out the current API is not that compatible with
some Microsoft mice, so better start again from scratch.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Harry Cutts <hcutts@chromium.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 3fe1d6bbcd.
It turns out the current API is not that compatible with
some Microsoft mice, so better start again from scratch.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Harry Cutts <hcutts@chromium.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 5fe2ccbef9.
It turns out the current API is not that compatible with
some Microsoft mice, so better start again from scratch.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Harry Cutts <hcutts@chromium.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Fix the following compile warning:
drivers/hid/hid-logitech-hidpp.c: In function 'hi_res_scroll_enable':
drivers/hid/hid-logitech-hidpp.c:2714:54: warning: 'multiplier' may be used uninitialized in this function [-Wmaybe-uninitialized]
hidpp->vertical_wheel_counter.resolution_multiplier = multiplier;
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Christophe JAILLET