The panel datasheet specifies a 500ms delay after power-down before
re-enabling.
Changes in v2:
- None
Changes in v3:
- Added to the set
Cc: Sandeep Panda <spanda@codeaurora.org>
Reviewed-by: Sandeep Panda <spanda@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180813213058.184821-2-sean@poorly.run
The change adds support for Sharp LQ035Q7DB03 3.5" QVGA TFT panel.
Note that this aged panel is already found in the kernel sources,
for instance in board mach files mach-mx21ads.c, mach-mx27ads.c,
mach-pcm043.c, lpd270.c and imx27-phytec-phycore-rdk.dts.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706185101.31186-1-vz@mleia.com
This adds support for the DataImage SCF0700C48GGU18 7.0" WVGA (800x480)
TFT LCD panel. The panel has 24-bit parallel interface and can be
supported by the simple panel driver.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1529930490-11874-2-git-send-email-michal.vokac@ysoft.com
The patch adds support for BOE HV070WSA-100 WSVGA 7.01 inch panel to the
panel-simple driver. The panel is used in Exynos5250-arndale boards.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1529396370-18761-6-git-send-email-m.purski@samsung.com
This patch adds support for DLC DLC0700YZG-1 1024x600 LVDS panels
to the simple-panel driver.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
[m.felsch@pengutronix.de: fix typo in compatible dt-binding]
[m.felsch@pengutronix.de: add property bindings]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180523092504.5142-3-m.felsch@pengutronix.de
The Emerging Display Technology ETM0700G0EDH6 is the
uses the same panel as the ETM0700G0BDH6. It differs
in the hardware design for the backlight and the
touchscreen i2c interface. As the new display type has
different requirements for drive-strengths on the i2c-bus,
add an additional compatible to allow the handling of it or warn
about incompatible cpu and display combinations.
Signed-off-by: Jan Tuerk <jan.tuerk@emtrion.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180619095546.24445-3-jan.tuerk@emtrion.com
The Emerging Display Technology ETM0700G0BDH6 is exactly
the same display as the ETM0700G0DH6, exept the pixelclock
polarity. Therefore re-use the ETM0700G0DH6 modes. It is
used by default on emtrion Avari based development kits.
Signed-off-by: Jan Tuerk <jan.tuerk@emtrion.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180619095546.24445-2-jan.tuerk@emtrion.com
This adds support for the Rocktech Display Ltd. RK070ER9427
800(RGB)x480 TFT LCD panel, which can be supported by the
simple panel driver.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180607134648.2902-1-jagan@amarulasolutions.com
All values in a struct struct timing_entry (every entry in
struct display_timing) require an integer. Choose the closest
safe integer of 32.
This avoids a warning seen with clang:
drivers/gpu/drm/panel/panel-simple.c:1250:27: warning: implicit
conversion from 'double' to 'u32' (aka 'unsigned int')
changes value from 33.5 to 33 [-Wliteral-conversion]
.vfront_porch = { 6, 21, 33.5 },
~ ^~~~
drivers/gpu/drm/panel/panel-simple.c:1251:26: warning: implicit
conversion from 'double' to 'u32' (aka 'unsigned int')
changes value from 33.5 to 33 [-Wliteral-conversion]
.vback_porch = { 6, 21, 33.5 },
~ ^~~~
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180419212003.8155-1-stefan@agner.ch
The patch adding support for the AUO P320HVN03 panel was written against a
preliminary datasheet, which specified JEIDA data ordering. Testing with
real hardware has shown that the actually used data ordering is SPWG.
Fixes: 70c0d5b783 (drm/panel: simple: add support for AUO P320HVN03)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180411152741.22483-1-l.stach@pengutronix.de
Add support for Innolux TV123WAM, which is a 12.3" eDP display panel
with 2160x1440 resolution.
Changes in v1:
- Add the compatibility string, display_mode and panel_desc
structures in alphabetical order (Sean Paul).
Signed-off-by: Sandeep Panda <spanda@codeaurora.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1526363564-13823-4-git-send-email-spanda@codeaurora.org
Remove all drm_panel_detach() calls from all panel drivers and update
the kerneldoc for drm_panel_detach().
Setting the connector and drm to NULL when the DRM panel device is going
away hardly serves any purpose. Usually the whole memory structure is
freed right after the remove call. However, calling the detach function
from the master DRM device, and setting the connector pointer to NULL,
has the logic of marking the panel again as available for another DRM
master to attach. The usual situation would be the same DRM master
device binding again.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/464b8d330d6b4c94cfb5aad2ca9ea7eb2c52d934.1524727888.git.jsarha@ti.com
This patch adds support for AUO G104SN02 V2 800x600 10.4" panel to DRM
simple panel driver.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1513430016.1930.4.camel@googlemail.com
Convert the sharp lq123p1jx31 from using a fixed mode to specifying a
display timing with min/typ/max values. This allows us to capture the
timings set forth in the datasheet as well as the additional values that
we've cleared with the display vendor to avoid interference with the
digitizer on the Samsung Chromebook Plus (kevin).
A follow-on patch will specify the override mode for kevin devices.
Changes in v2:
- None
Changes in v3:
- None
Cc: Doug Anderson <dianders@chromium.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Jeffy Chen <jeffy.chen@rock-chips.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Stéphane Marchesin <marcheu@chromium.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: devicetree@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180208174855.55620-6-seanpaul@chromium.org
This fixes bad color output. When I was first testing the device I
had the DPI hardware set to 666 mode, but apparently in the refactor
to use the bus_format information from the panel driver, I failed to
actually update the panel.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: e8b6f561b2 ("drm/panel: simple: Add the 7" DPI panel from Adafruit")
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180309233332.1769-1-eric@anholt.net
The Mitsubishi AA070MC01 is a 7.0" WVGA (800x480) TFT panel working in
8 bit ISP mode (pin 19 "mode" HIGH for 20 pin TFT connector).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1508537917-1723-1-git-send-email-lukma@denx.de
The Tianma TM070RVHG71 is a 7" WVGA (800x480) TFT LCD panel connected
via LVDS and can be supported by the simple-panel binding.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171107153058.5554-1-lukma@denx.de
Only exposes a single mode and not a complete display timing, as
the datasheet is rather vague about the minimum/maximum values.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171018172240.8772-1-l.stach@pengutronix.de
The delays between video data and backlight enable and between backlight
disable and end of video data are given as >= 160 ms in the datasheet.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171011125958.23064-3-p.zabel@pengutronix.de
For LCD interface controllers that support configuring polarity of
pixel clock and data enable signal, specify bus flags in the panel
descriptor.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171011125958.23064-2-p.zabel@pengutronix.de
The vsync length should be 10 lines, as specified in the data sheet.
This gets the actual refresh rate closer to nominal 60 Hz given the
9 MHz pixel clock.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171011125958.23064-1-p.zabel@pengutronix.de
During panel removal or system shutdown panel_simple_disable() is called
which disables the panel backlight but the panel is still powered due to
missing calls to panel_simple_unprepare().
Fixes: d02fd93e2c ("drm/panel: simple - Disable panel on shutdown")
Cc: stable@vger.kernel.org # v3.16+
Signed-off-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170807115545.27747-1-net147@gmail.com
The physical size of the panel is 105.5 (W) x 67.2 (H) x 4.05 (D) mm
but the active display area is 95.04 (W) x 53.856 (H) mm.
The width and height should be set to the active display area.
Signed-off-by: Jonathan Liu <net147@gmail.com>
Fixes: cf5c9e6dc7 ("drm/panel: simple: Add timings for the Olimex LCD-OLinuXino-4.3TS")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170720102943.25091-1-net147@gmail.com
When enable_gpio is provided via an I2C or SPI expander, it may not be
available when panel-simple probes leading to the following error:
panel-simple panel: failed to request GPIO: -517
As this error message is not very useful to the end user, skip printing
it in the case of deferred probe.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1498857286-10820-1-git-send-email-festevam@gmail.com
This adds support for the AU Optronics Corporation 31.5"
FHD (1920x1080) LVDS TFT LCD panel, which can be supported
by the simple panel driver
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170608180758.31020-4-l.stach@pengutronix.de
This adds support for the NLT Technologies NL192108AC18-02D
15.6" LVDS FullHD TFT LCD panel, which can be supported
by the simple panel driver.
Timings are taken from the preliminary datasheet, as a final
one is not yet available.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170608180758.31020-3-l.stach@pengutronix.de
This adds support for the Winstar Display Co. WF35LTIACD 3.5" QVGA TFT
LCD panel, which can be supported by the simple panel driver.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add simple-panel support for the Ampire AM-480272H3TMQW-T01H, which is a
4.3" WQVGA panel.
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The display has a 18-Bit parallel LCD interface, require DE to be
active high and data driven by the controller on falling pixel
clock edge (display samples on rising edge).
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The E231732 is a 7" panel with a resolution of 1024x600.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[treding@nvidia.com: add missing device tree binding]
Signed-off-by: Thierry Reding <treding@nvidia.com>
The BOE NV101WXMN51 is a 10.1" WXGA color active matrix TFT LCD module
using amorphous silicon TFT's as an active switching devices. It can be
supported by the simple-panel driver.
Read the panel default EDID information:
EDID MODE DETAILS
name = <NULL>
pixel_clock = 71900
lvds_dual_channel = 0
refresh = 0
ha = 1280
hbl = 160
hso = 48
hspw = 32
hborder = 0
va = 800
vbl = 32
vso = 3
vspw = 5
vborder = 0
phsync = +
pvsync = -
x_mm = 0
y_mm = 0
drm_display_mode
.hdisplay = 1280
.hsync_start = 1328
.hsync_end = 1360
.htotal = 1440
.vdisplay = 800
.vsync_start = 803
.vsync_end = 808
.vtotal = 832
There are two modes in the EDID:
Detailed mode1: Clock 71.900 MHz, 216 mm x 135 mm
1280 1328 1360 1440 hborder 0
800 803 808 832 vborder 0
+hsync -vsync
Detailed mode2: Clock 57.500 MHz, 216 mm x 135 mm
1280 1328 1360 1440 hborder 0
800 803 808 832 vborder 0
+hsync -vsync
Support both of these modes on the panel.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This adds support for the AU Optronics G185HAN01 18.5" LVDS FullHD TFT
LCD panel, which can be supported by the simple panel driver.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This adds support for the AU Optronics G133HAN01 13.3" LVDS FullHD TFT
LCD panel, which can be supported by the simple panel driver.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Convert from a single mode to display timings, which allow to describe
the minimum/maximium blanking and clock rates, add enable/disable delays
and provide the bus format.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Sharp LQ123P1JX31 panel support 8 bits per component.
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In the loop on .timings, we should check .num_timings to see if it's the
only mode specified, not .num_modes, which should be used with .modes.
Fixes: cda553725c ("drm/panel: simple: Set appropriate mode type")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Chunghwa CLAA070WP03XG is a 7" 1280x800 panel, which can be
supported by the simple panel driver.
Signed-off-by: Randy Li <ayaka@soulik.info>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The AUO T215HVN01 is a 21.5" FHD (1920x1080) color TFT LCD panel.
This panel is used on the Acer Chromebase 21.5-inch All-in-One (DC221HQ).
Link to spec: http://www.udmgroup.com/ftp/T215HVN01.0.pdf
v2: fix alphabetical order
v3: remove minor revision suffix ".0" and add link to spec
v4: add dt-binding documentation
Signed-off-by: Haixia Shi <hshi@chromium.org>
Tested-by: Haixia Shi <hshi@chromium.org>
Reviewed-by: Stéphane Marchesin <marcheu@chromium.org>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Sharp 15" LQ150X1LG11 panel is an XGA TFT LCD panel.
The simple-panel driver is used to get support for essential
functionality of the panel.
Signed-off-by: Gustaf Lindström <gl@axentia.se>
Signed-off-by: Peter Rosin <peda@axentia.se>
[treding@nvidia.com: change .bpc from 8 to 6]
Signed-off-by: Thierry Reding <treding@nvidia.com>
The format is RGB888 not RGB666.
Signed-off-by: Jonathan Liu <net147@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Taking our cue from commit a42f6e3f8f ("drm/panel: simple: Add delay
timing for Sharp LQ123P1JX31"), let's add timings:
.prepare = t1 + t3
.enable = t7
.unprepare = t11 + 12
Without this, the panel may not be given enough time to come up.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Sean Paul