Only show the 'calibrate' sysfs attribute on chip flavours
which support calibration by writing to a calibration register.
Do this by adding a flag to the chip operations structure.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Link: https://lore.kernel.org/r/20191112210148.3535-2-TheSven73@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Optionally allow the touch screen resolution to be set by adding
it to the chip operations structure. If it is omitted (left zero),
the resolution defaults to 64K. Which is the previously hard-coded
value.
Set the ili2117 resolution to 2048, as indicated in its datasheet.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Link: https://lore.kernel.org/r/20191112210148.3535-1-TheSven73@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver's method to retrieve the firmware version on ili2117/
ili2118 chip flavours is incorrect. The firmware version register
address and layout are wrong.
The firmware version is not actually used anywhere inside or
outside this driver. There is a dev_dbg() print, but that is
only visible when the developer explicitly compiles in debug
support.
Don't make the code more complicated to preserve a feature that
no-one is using. Remove all code associated with chip firmware
version.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Link: https://lore.kernel.org/r/20191112164429.11225-1-TheSven73@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When I2C client is instantiated with I2C_CLIENT_WAKE flag (either via
"wakeup-source" device property, or via board info flag), it will mark the
main IRQ line as wakeup IRQ, which will ensure that it will be enabled for
wakeup when system transitions to suspend state. Since our suspend/resume
handlers were only managing IRQ wakeup state, they are no longer needed,
and can be removed.
Tested-by: Adam Ford <aford173@gmail.com> #imx6q-logicpd
Tested-by: Sven Van Asbroeck <TheSven73@gmail.com> # ILI2118A variant
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
I2C devices that are supposed to be wakeup sources should be instantiated
with I2C_CLIENT_WAKE flag (which can be either set by in board info, or
retrieved from "wakeup-source" property); individual drivers should not be
marking devices as wakeup sources unconditionally.
Tested-by: Adam Ford <aford173@gmail.com> #imx6q-logicpd
Tested-by: Sven Van Asbroeck <TheSven73@gmail.com> # ILI2118A variant
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of doing if/else if/else on the chip's model number let's define
chip operations structure and use it to perform indirect calls. With number
of protocols supported by the driver growing, this makes it better
maintainable.
This change includes fixes to checks whether the driver should continue
polling the controller by Sven Van Asbroeck <thesven73@gmail.com>.
Tested-by: Adam Ford <aford173@gmail.com> #imx6q-logicpd
Tested-by: Sven Van Asbroeck <TheSven73@gmail.com> # ILI2118A variant
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We are using devm_input_allocate_device() that set's up the parent for
us, no need to do it ourselves.
Tested-by: Adam Ford <aford173@gmail.com> #imx6q-logicpd
Tested-by: Sven Van Asbroeck <TheSven73@gmail.com> # ILI2118A variant
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
input_mt_init_slots() may fail and we need to handle such failures.
Tested-by: Adam Ford <aford173@gmail.com> #imx6q-logicpd
Tested-by: Sven Van Asbroeck <TheSven73@gmail.com> # ILI2118A variant
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch the driver to using threaded IRQ so that we do not need to
manage the interrupt and work separately, and we do not acknowledge
interrupt until we finished handling it completely.
Tested-by: Adam Ford <aford173@gmail.com> #imx6q-logicpd
Tested-by: Sven Van Asbroeck <TheSven73@gmail.com> # ILI2118A variant
Tested-by: Marek Vasut <marex@denx.de> # ILI2117
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for ILI2117 touch controller. This controller is similar
to the ILI210x and ILI251x, except for the following differences:
- Reading out of touch data must happen at most 300 mS after the
interrupt line was asserted. No command must be sent, the data
are returned upon pure I2C read of 43 bytes long.
- Supports 10 simultaneous touch inputs.
- Touch data format is slightly different.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Rob Herring <robh@kernel.org> # for DT binding
Tested-by: Adam Ford <aford173@gmail.com> #imx6q-logicpd
Tested-by: Sven Van Asbroeck <TheSven73@gmail.com> # ILI2118A variant
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fetching the geometry from the ILI251x registers seems unreliable and
sometimes returns all zeroes. Add support for fetching the geometry and
axis inversion from DT instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
By switching to devm_device_add_group() we can complete driver conversion
to using managed resources and get rid of ili210x_i2c_remove().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for ILI251x touch controller. This controller is similar
to the ILI210x, except for the following differences:
- Does not support I2C R-W transfer, Read must be followed by an
obscenely long delay, and then followed by Write
- Does support 10 simultaneous touch inputs.
- Touch data format is slightly different, pressure reporting does not
work although the touch data contain such information.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Perform the register access only after the I2C client data are set,
this is only done in preparation for the subsequent patch which
uses the I2C client data in the register IO function.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Get rid of the packed structures for representing data as that does not
apply to other similar Ilitek touchscreens. Instead, implement a function
which parses the data and reports touch events and coordinates.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Convert the driver to devm_request_irq(), drop the related unmanaged
deregistration code and add ili210x_irq_teardown() to tear the IRQ
down and cancel possible touchscreen pending work.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The touchscreen can have a reset GPIO connected to it, add support
for such an arrangement.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The .get_pendown_state callback is set only by the platform data code,
which was just removed. Thus, get_pendown_state() always returns false,
so drop that altogether.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is not a single user of the ili210x platform data in the kernel,
just drop it.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since there is no call to dev_get_drvdata() or input_get_drvdata(),
the call to input_set_drvdata() is unnecessary and can be dropped.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If a function declares a variable to access a structure element,
use it consistently.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
"calibrate" attribute does not provide "show" methods and thus we should
not mark it as readable.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch fix spelling typo inv various part of sources.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use __maybe_unused instead of ifdef guards around suspend/resume
functions, in order to increase build coverage and fix build warnings.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use the wrapper function for retrieving the platform data instead
of accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Preparing to move more repeated code into the mt core, add a flags
argument to the input_mt_slots_init() function.
Reviewed-and-tested-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Tested-by: Ping Cheng <pingc@wacom.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
The driver supports chipsets ILI2102, ILI2102s, ILI2103, ILI2103s and
ILI2105. Such kind of controllers can be found in Amazon Kindle Fire
devices.
Reviewed-by: Jan Paesmans <jan.paesmans@gmail.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Sven Van Asbroeck