nvme_rdma_alloc_tagset() preallocates a big buffer for the IO SGL based
on SG_CHUNK_SIZE.
Modern DMA engines are often capable of dealing with very big segments so
the SG_CHUNK_SIZE is often too big. SG_CHUNK_SIZE results in a static 4KB
SGL allocation per command.
If a controller has lots of deep queues, preallocation for the sg list can
consume substantial amounts of memory. For nvme-rdma, nr_hw_queues can be
128 and each queue's depth 128. This means the resulting preallocation
for the data SGL is 128*128*4K = 64MB per controller.
Switch to runtime allocation for SGL for lists longer than 2 entries. This
is the approach used by NVMe PCI so it should be reasonable for NVMeOF as
well. Runtime SGL allocation has always been the case for the legacy I/O
path so this is nothing new.
The preallocated small SGL depends on SG_CHAIN so if the ARCH doesn't
support SG_CHAIN, use only runtime allocation for the SGL.
We didn't notice of a performance degradation, since for small IOs we'll
use the inline SG and for the bigger IOs the allocation of a bigger SGL
from slab is fast enough.
Suggested-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
-----BEGIN PGP SIGNATURE-----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=oyE3
-----END PGP SIGNATURE-----
Merge tag 'for-5.5/drivers-post-20191122' of git://git.kernel.dk/linux-block
Pull additional block driver updates from Jens Axboe:
"Here's another block driver update, done to avoid conflicts with the
zoned changes coming next.
This contains:
- Prepare SCSI sd for zone open/close/finish support
- Small NVMe pull request
- hwmon support (Akinobu)
- add new co-maintainer (Christoph)
- work-around for a discard issue on non-conformant drives
(Eduard)
- Small nbd leak fix"
* tag 'for-5.5/drivers-post-20191122' of git://git.kernel.dk/linux-block:
nbd: prevent memory leak
nvme: hwmon: add quirk to avoid changing temperature threshold
nvme: hwmon: provide temperature min and max values for each sensor
nvmet: add another maintainer
nvme: Discard workaround for non-conformant devices
nvme: Add hardware monitoring support
scsi: sd_zbc: add zone open, close, and finish support
-----BEGIN PGP SIGNATURE-----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=i0jf
-----END PGP SIGNATURE-----
Merge tag 'for-5.5/drivers-20191121' of git://git.kernel.dk/linux-block
Pull block driver updates from Jens Axboe:
"Here are the main block driver updates for 5.5. Nothing major in here,
mostly just fixes. This contains:
- a set of bcache changes via Coly
- MD changes from Song
- loop unmap write-zeroes fix (Darrick)
- spelling fixes (Geert)
- zoned additions cleanups to null_blk/dm (Ajay)
- allow null_blk online submit queue changes (Bart)
- NVMe changes via Keith, nothing major here either"
* tag 'for-5.5/drivers-20191121' of git://git.kernel.dk/linux-block: (56 commits)
Revert "bcache: fix fifo index swapping condition in journal_pin_cmp()"
drivers/md/raid5-ppl.c: use the new spelling of RWH_WRITE_LIFE_NOT_SET
drivers/md/raid5.c: use the new spelling of RWH_WRITE_LIFE_NOT_SET
bcache: don't export symbols
bcache: remove the extra cflags for request.o
bcache: at least try to shrink 1 node in bch_mca_scan()
bcache: add idle_max_writeback_rate sysfs interface
bcache: add code comments in bch_btree_leaf_dirty()
bcache: fix deadlock in bcache_allocator
bcache: add code comment bch_keylist_pop() and bch_keylist_pop_front()
bcache: deleted code comments for dead code in bch_data_insert_keys()
bcache: add more accurate error messages in read_super()
bcache: fix static checker warning in bcache_device_free()
bcache: fix a lost wake-up problem caused by mca_cannibalize_lock
bcache: fix fifo index swapping condition in journal_pin_cmp()
md/raid10: prevent access of uninitialized resync_pages offset
md: avoid invalid memory access for array sb->dev_roles
md/raid1: avoid soft lockup under high load
null_blk: add zone open, close, and finish support
dm: add zone open, close and finish support
...
This adds a new quirk NVME_QUIRK_NO_TEMP_THRESH_CHANGE to avoid changing
the value of the temperature threshold feature for specific devices that
show undesirable behavior.
Guenter reported:
"On my Intel NVME drive (SSDPEKKW512G7), writing any minimum limit on the
Composite temperature sensor results in a temperature warning, and that
warning is sticky until I reset the controller.
It doesn't seem to matter which temperature I write; writing -273000 has
the same result."
The Intel NVMe has the latest firmware version installed, so this isn't
a problem that was ever fixed.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: Keith Busch <kbusch@kernel.org>
Cc: Jens Axboe <axboe@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Jean Delvare <jdelvare@suse.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
nvme devices report temperature information in the controller information
(for limits) and in the smart log. Currently, the only means to retrieve
this information is the nvme command line interface, which requires
super-user privileges.
At the same time, it would be desirable to be able to use NVMe temperature
information for thermal control.
This patch adds support to read NVMe temperatures from the kernel using the
hwmon API and adds temperature zones for NVMe drives. The thermal subsystem
can use this information to set thermal policies, and userspace can access
it using libsensors and/or the "sensors" command.
Example output from the "sensors" command:
nvme0-pci-0100
Adapter: PCI adapter
Composite: +39.0°C (high = +85.0°C, crit = +85.0°C)
Sensor 1: +39.0°C
Sensor 2: +41.0°C
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Introduce the new helper function nvme_lba_to_sect() to convert a device
logical block number to a 512B sector number. Use this new helper in
obvious places, cleaning up the code.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Rename nvme_block_nr() to nvme_sect_to_lba() and use SECTOR_SHIFT
instead of its hard coded value 9. Also add a comment to decribe this
helper.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This function improves code readability and reduces code duplication.
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Prevent simultaneous controller disabling/enabling tasks from interfering
with each other through a function to wait until the task successfully
transitioned the controller to the RESETTING state. This ensures disabling
the controller will not be interrupted by another reset path, otherwise
a concurrent reset may leave the controller in the wrong state.
Tested-by: Edmund Nadolski <edmund.nadolski@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
The admin only state was intended to fence off actions that don't
apply to a non-IO capable controller. The only actual user of this is
the scan_work, and pci was the only transport to ever set this state.
The consequence of having this state is placing an additional burden on
every other action that applies to both live and admin only controllers.
Remove the admin only state and place the admin only burden on the only
place that actually cares: scan_work.
This also prepares to make it easier to temporarily pause a LIVE state
so that we don't need to remember which state the controller had been in
prior to the pause.
Tested-by: Edmund Nadolski <edmund.nadolski@intel.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Qt+h
-----END PGP SIGNATURE-----
Merge tag 'for-5.4/block-2019-09-16' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
- Two NVMe pull requests:
- ana log parse fix from Anton
- nvme quirks support for Apple devices from Ben
- fix missing bio completion tracing for multipath stack devices
from Hannes and Mikhail
- IP TOS settings for nvme rdma and tcp transports from Israel
- rq_dma_dir cleanups from Israel
- tracing for Get LBA Status command from Minwoo
- Some nvme-tcp cleanups from Minwoo, Potnuri and Myself
- Some consolidation between the fabrics transports for handling
the CAP register
- reset race with ns scanning fix for fabrics (move fabrics
commands to a dedicated request queue with a different lifetime
from the admin request queue)."
- controller reset and namespace scan races fixes
- nvme discovery log change uevent support
- naming improvements from Keith
- multiple discovery controllers reject fix from James
- some regular cleanups from various people
- Series fixing (and re-fixing) null_blk debug printing and nr_devices
checks (André)
- A few pull requests from Song, with fixes from Andy, Guoqing,
Guilherme, Neil, Nigel, and Yufen.
- REQ_OP_ZONE_RESET_ALL support (Chaitanya)
- Bio merge handling unification (Christoph)
- Pick default elevator correctly for devices with special needs
(Damien)
- Block stats fixes (Hou)
- Timeout and support devices nbd fixes (Mike)
- Series fixing races around elevator switching and device add/remove
(Ming)
- sed-opal cleanups (Revanth)
- Per device weight support for BFQ (Fam)
- Support for blk-iocost, a new model that can properly account cost of
IO workloads. (Tejun)
- blk-cgroup writeback fixes (Tejun)
- paride queue init fixes (zhengbin)
- blk_set_runtime_active() cleanup (Stanley)
- Block segment mapping optimizations (Bart)
- lightnvm fixes (Hans/Minwoo/YueHaibing)
- Various little fixes and cleanups
* tag 'for-5.4/block-2019-09-16' of git://git.kernel.dk/linux-block: (186 commits)
null_blk: format pr_* logs with pr_fmt
null_blk: match the type of parameter nr_devices
null_blk: do not fail the module load with zero devices
block: also check RQF_STATS in blk_mq_need_time_stamp()
block: make rq sector size accessible for block stats
bfq: Fix bfq linkage error
raid5: use bio_end_sector in r5_next_bio
raid5: remove STRIPE_OPS_REQ_PENDING
md: add feature flag MD_FEATURE_RAID0_LAYOUT
md/raid0: avoid RAID0 data corruption due to layout confusion.
raid5: don't set STRIPE_HANDLE to stripe which is in batch list
raid5: don't increment read_errors on EILSEQ return
nvmet: fix a wrong error status returned in error log page
nvme: send discovery log page change events to userspace
nvme: add uevent variables for controller devices
nvme: enable aen regardless of the presence of I/O queues
nvme-fabrics: allow discovery subsystems accept a kato
nvmet: Use PTR_ERR_OR_ZERO() in nvmet_init_discovery()
nvme: Remove redundant assignment of cq vector
nvme: Assign subsys instance from first ctrl
...
We have a fundamental issue that fabric commands use the admin_q.
The reason is, that admin-connect, register reads and writes and
admin commands cannot be guaranteed ordering while we are running
controller resets.
For example, when we reset a controller we perform:
1. disable the controller
2. teardown the admin queue
3. re-establish the admin queue
4. enable the controller
In order to perform (3), we need to unquiesce the admin queue, however
we may have some admin commands that are already pending on the
quiesced admin_q and will immediate execute when we unquiesce it before
we execute (4). The host must not send admin commands to the controller
before enabling the controller.
To fix this, we have the fabric commands (admin connect and property
get/set, but not I/O queue connect) use a separate fabrics_q and make
sure to quiesce the admin_q before we disable the controller, and
unquiesce it only after we enable the controller.
This fixes the error prints from nvmet in a controller reset storm test:
kernel: nvmet: got cmd 6 while CC.EN == 0 on qid = 0
Which indicate that the host is sending an admin command when the
controller is not enabled.
Reviewed-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Another issue with the Apple T2 based 2018 controllers seem to be
that they blow up (and shut the machine down) if there's a tag
collision between the IO queue and the Admin queue.
My suspicion is that they use our tags for their internal tracking
and don't mix them with the queue id. They also seem to not like
when tags go beyond the IO queue depth, ie 128 tags.
This adds a quirk that marks tags 0..31 of the IO queue reserved
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Acked-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Based on reverse engineering and original patch by
Paul Pawlowski <paul@mrarm.io>
This adds support for Apple weird implementation of NVME in their
2018 or later machines. It accounts for the twice-as-big SQ entries
for the IO queues, and the fact that only interrupt vector 0 appears
to function properly.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
When native multipathing is enabled we cannot enable blktrace for
the underlying paths, so any completion is never traced.
Signed-off-by: Hannes Reinecke <hare@suse.com>
[fixed-up by Mikhail for non-multipath-build]
Signed-off-by: Mikhail Skorzhinskii <mskorzhinskiy@solarflare.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
All seem to call it with ctrl->cap so no need to pass it
at all.
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
nvme_enable_ctrl reads the cap register right after, so
no need to do that locally in the transport driver. Have
sqsize setting in nvme_init_identify.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
One of the components in LiteON CL1 device has limitations that
can be encountered based upon boundary race conditions using the
nvme bus specific suspend to idle flow.
When this situation occurs the drive doesn't resume properly from
suspend-to-idle.
LiteON has confirmed this problem and fixed in the next firmware
version. As this firmware is already in the field, avoid running
nvme specific suspend to idle flow.
Fixes: d916b1be94 ("nvme-pci: use host managed power state for suspend")
Link: http://lists.infradead.org/pipermail/linux-nvme/2019-July/thread.html
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Charles Hyde <charles.hyde@dellteam.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
With multipath enabled, nvme_scan_work() can read from the device
(through nvme_mpath_add_disk()) and hang [1]. However, with fabrics,
once ctrl->state is set to NVME_CTRL_DELETING, the reads will hang
(see nvmf_check_ready()) and the mpath stack device make_request
will block if head->list is not empty. However, when the head->list
consistst of only DELETING/DEAD controllers, we should actually not
block, but rather fail immediately.
In addition, before we go ahead and remove the namespaces, make sure
to clear the current path and kick the requeue list so that the
request will fast fail upon requeuing.
[1]:
--
INFO: task kworker/u4:3:166 blocked for more than 120 seconds.
Not tainted 5.2.0-rc6-vmlocalyes-00005-g808c8c2dc0cf #316
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
kworker/u4:3 D 0 166 2 0x80004000
Workqueue: nvme-wq nvme_scan_work
Call Trace:
__schedule+0x851/0x1400
schedule+0x99/0x210
io_schedule+0x21/0x70
do_read_cache_page+0xa57/0x1330
read_cache_page+0x4a/0x70
read_dev_sector+0xbf/0x380
amiga_partition+0xc4/0x1230
check_partition+0x30f/0x630
rescan_partitions+0x19a/0x980
__blkdev_get+0x85a/0x12f0
blkdev_get+0x2a5/0x790
__device_add_disk+0xe25/0x1250
device_add_disk+0x13/0x20
nvme_mpath_set_live+0x172/0x2b0
nvme_update_ns_ana_state+0x130/0x180
nvme_set_ns_ana_state+0x9a/0xb0
nvme_parse_ana_log+0x1c3/0x4a0
nvme_mpath_add_disk+0x157/0x290
nvme_validate_ns+0x1017/0x1bd0
nvme_scan_work+0x44d/0x6a0
process_one_work+0x7d7/0x1240
worker_thread+0x8e/0xff0
kthread+0x2c3/0x3b0
ret_from_fork+0x35/0x40
INFO: task kworker/u4:1:1034 blocked for more than 120 seconds.
Not tainted 5.2.0-rc6-vmlocalyes-00005-g808c8c2dc0cf #316
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
kworker/u4:1 D 0 1034 2 0x80004000
Workqueue: nvme-delete-wq nvme_delete_ctrl_work
Call Trace:
__schedule+0x851/0x1400
schedule+0x99/0x210
schedule_timeout+0x390/0x830
wait_for_completion+0x1a7/0x310
__flush_work+0x241/0x5d0
flush_work+0x10/0x20
nvme_remove_namespaces+0x85/0x3d0
nvme_do_delete_ctrl+0xb4/0x1e0
nvme_delete_ctrl_work+0x15/0x20
process_one_work+0x7d7/0x1240
worker_thread+0x8e/0xff0
kthread+0x2c3/0x3b0
ret_from_fork+0x35/0x40
--
Reported-by: Logan Gunthorpe <logang@deltatee.com>
Tested-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
When the user issues a command with side effects, we will end up freezing
the namespace request queue when updating disk info (and the same for
the corresponding mpath disk node).
However, we are not freezing the mpath node request queue,
which means that mpath I/O can still come in and block on blk_queue_enter
(called from nvme_ns_head_make_request -> direct_make_request).
This is a deadlock, because blk_queue_enter will block until the inner
namespace request queue is unfroze, but that process is blocked because
the namespace revalidation is trying to update the mpath disk info
and freeze its request queue (which will never complete because
of the I/O that is blocked on blk_queue_enter).
Fix this by freezing all the subsystem nsheads request queues before
executing the passthru command. Given that these commands are infrequent
we should not worry about this temporary I/O freeze to keep things sane.
Here is the matching hang traces:
--
[ 374.465002] INFO: task systemd-udevd:17994 blocked for more than 122 seconds.
[ 374.472975] Not tainted 5.2.0-rc3-mpdebug+ #42
[ 374.478522] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 374.487274] systemd-udevd D 0 17994 1 0x00000000
[ 374.493407] Call Trace:
[ 374.496145] __schedule+0x2ef/0x620
[ 374.500047] schedule+0x38/0xa0
[ 374.503569] blk_queue_enter+0x139/0x220
[ 374.507959] ? remove_wait_queue+0x60/0x60
[ 374.512540] direct_make_request+0x60/0x130
[ 374.517219] nvme_ns_head_make_request+0x11d/0x420 [nvme_core]
[ 374.523740] ? generic_make_request_checks+0x307/0x6f0
[ 374.529484] generic_make_request+0x10d/0x2e0
[ 374.534356] submit_bio+0x75/0x140
[ 374.538163] ? guard_bio_eod+0x32/0xe0
[ 374.542361] submit_bh_wbc+0x171/0x1b0
[ 374.546553] block_read_full_page+0x1ed/0x330
[ 374.551426] ? check_disk_change+0x70/0x70
[ 374.556008] ? scan_shadow_nodes+0x30/0x30
[ 374.560588] blkdev_readpage+0x18/0x20
[ 374.564783] do_read_cache_page+0x301/0x860
[ 374.569463] ? blkdev_writepages+0x10/0x10
[ 374.574037] ? prep_new_page+0x88/0x130
[ 374.578329] ? get_page_from_freelist+0xa2f/0x1280
[ 374.583688] ? __alloc_pages_nodemask+0x179/0x320
[ 374.588947] read_cache_page+0x12/0x20
[ 374.593142] read_dev_sector+0x2d/0xd0
[ 374.597337] read_lba+0x104/0x1f0
[ 374.601046] find_valid_gpt+0xfa/0x720
[ 374.605243] ? string_nocheck+0x58/0x70
[ 374.609534] ? find_valid_gpt+0x720/0x720
[ 374.614016] efi_partition+0x89/0x430
[ 374.618113] ? string+0x48/0x60
[ 374.621632] ? snprintf+0x49/0x70
[ 374.625339] ? find_valid_gpt+0x720/0x720
[ 374.629828] check_partition+0x116/0x210
[ 374.634214] rescan_partitions+0xb6/0x360
[ 374.638699] __blkdev_reread_part+0x64/0x70
[ 374.643377] blkdev_reread_part+0x23/0x40
[ 374.647860] blkdev_ioctl+0x48c/0x990
[ 374.651956] block_ioctl+0x41/0x50
[ 374.655766] do_vfs_ioctl+0xa7/0x600
[ 374.659766] ? locks_lock_inode_wait+0xb1/0x150
[ 374.664832] ksys_ioctl+0x67/0x90
[ 374.668539] __x64_sys_ioctl+0x1a/0x20
[ 374.672732] do_syscall_64+0x5a/0x1c0
[ 374.676828] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 374.738474] INFO: task nvmeadm:49141 blocked for more than 123 seconds.
[ 374.745871] Not tainted 5.2.0-rc3-mpdebug+ #42
[ 374.751419] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 374.760170] nvmeadm D 0 49141 36333 0x00004080
[ 374.766301] Call Trace:
[ 374.769038] __schedule+0x2ef/0x620
[ 374.772939] schedule+0x38/0xa0
[ 374.776452] blk_mq_freeze_queue_wait+0x59/0x100
[ 374.781614] ? remove_wait_queue+0x60/0x60
[ 374.786192] blk_mq_freeze_queue+0x1a/0x20
[ 374.790773] nvme_update_disk_info.isra.57+0x5f/0x350 [nvme_core]
[ 374.797582] ? nvme_identify_ns.isra.50+0x71/0xc0 [nvme_core]
[ 374.804006] __nvme_revalidate_disk+0xe5/0x110 [nvme_core]
[ 374.810139] nvme_revalidate_disk+0xa6/0x120 [nvme_core]
[ 374.816078] ? nvme_submit_user_cmd+0x11e/0x320 [nvme_core]
[ 374.822299] nvme_user_cmd+0x264/0x370 [nvme_core]
[ 374.827661] nvme_dev_ioctl+0x112/0x1d0 [nvme_core]
[ 374.833114] do_vfs_ioctl+0xa7/0x600
[ 374.837117] ? __audit_syscall_entry+0xdd/0x130
[ 374.842184] ksys_ioctl+0x67/0x90
[ 374.845891] __x64_sys_ioctl+0x1a/0x20
[ 374.850082] do_syscall_64+0x5a/0x1c0
[ 374.854178] entry_SYSCALL_64_after_hwframe+0x44/0xa9
--
Reported-by: James Puthukattukaran <james.puthukattukaran@oracle.com>
Tested-by: James Puthukattukaran <james.puthukattukaran@oracle.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
>From the NVMe 1.4 spec:
NSFEAT bit 4 if set to 1: indicates that the fields NPWG, NPWA, NPDG, NPDA,
and NOWS are defined for this namespace and should be used by the host for
I/O optimization;
[ ... ]
Namespace Preferred Write Granularity (NPWG): This field indicates the
smallest recommended write granularity in logical blocks for this namespace.
This is a 0's based value. The size indicated should be less than or equal
to Maximum Data Transfer Size (MDTS) that is specified in units of minimum
memory page size. The value of this field may change if the namespace is
reformatted. The size should be a multiple of Namespace Preferred Write
Alignment (NPWA). Refer to section 8.25 for how this field is utilized to
improve performance and endurance.
[ ... ]
Each Write, Write Uncorrectable, or Write Zeroes commands should address a
multiple of Namespace Preferred Write Granularity (NPWG) (refer to Figure
245) and Stream Write Size (SWS) (refer to Figure 515) logical blocks (as
expressed in the NLB field), and the SLBA field of the command should be
aligned to Namespace Preferred Write Alignment (NPWA) (refer to Figure 245)
for best performance.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This enables to inject errors into the commands submitted to the admin
queue.
It is useful to test error handling in the controller initialization.
# echo 100 > /sys/kernel/debug/nvme0/fault_inject/probability
# echo 1 > /sys/kernel/debug/nvme0/fault_inject/times
# echo 10 > /sys/kernel/debug/nvme0/fault_inject/space
# nvme reset /dev/nvme0
# dmesg
...
nvme nvme0: Could not set queue count (16385)
nvme nvme0: IO queues not created
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Currenlty fault injection support for nvme only enables to inject errors
into the commands submitted to I/O queues.
In preparation for fault injection into the admin commands, this makes
the helper functions independent of struct nvme_ns.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Future use intends to make use of both, so export these functions. And
since their implementation is identical except for the opcode, provide a
new function that implement both.
[akinobu.mita@gmail.com>: fix line over 80 characters]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
A controller with multiple namespaces may have multiple request_queues with
their own timeout work. If a controller fails with IO outstanding to
diffent namespaces, each request queue may attempt to handle it, so
ensure there is no previously scheduled timeout work executing prior to
starting controller initialization by synchronizing with each queue.
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Qemu started out with a broken implementation of Write Zeroes written
by yours truly. Disable Write Zeroes on qemu for now, eventually
we need to go back and make all the qemu quirks version specific,
but that is left for another time.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Tested-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Update license to use SPDX-License-Identifier instead of verbose license
text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Since nvme_delete_ctrl_sync() is not called from any other kernel module,
unexport it.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Implement a simple round-robin I/O policy for multipathing. Path
selection is done in two rounds, first iterating across all optimized
paths, and if that doesn't return any valid paths, iterate over all
optimized and non-optimized paths. If no paths are found, use the
existing algorithm. Also add a sysfs attribute 'iopolicy' to switch
between the current NUMA-aware I/O policy and the 'round-robin' I/O
policy.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
-----BEGIN PGP SIGNATURE-----
iQFRBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlxgqNUeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGwsoH+OVXu0NQofwTvVru
8lgF3BSDG2mhf7mxbBBlBizGVy9jnjRNGCFMC+Jq8IwiFLwprja/G27kaDTkpuF1
PHC3yfjKvjTeUP5aNdHlmxv6j1sSJfZl0y46DQal4UeTG/Giq8TFTi+Tbz7Wb/WV
yCx4Lr8okAwTuNhnL8ojUCVIpd3c8QsyR9v6nEQ14Mj+MvEbokyTkMJV0bzOrM38
JOB+/X1XY4JPZ6o3MoXrBca3bxbAJzMneq+9CWw1U5eiIG3msg4a+Ua3++RQMDNr
8BP0yCZ6wo32S8uu0PI6HrZaBnLYi5g9Wh7Q7yc0mn1Uh1zWFykA6TtqK90agJeR
A6Ktjw==
=scY4
-----END PGP SIGNATURE-----
Merge tag 'v5.0-rc6' into for-5.1/block
Pull in 5.0-rc6 to avoid a dumb merge conflict with fs/iomap.c.
This is needed since io_uring is now based on the block branch,
to avoid a conflict between the multi-page bvecs and the bits
of io_uring that touch the core block parts.
* tag 'v5.0-rc6': (525 commits)
Linux 5.0-rc6
x86/mm: Make set_pmd_at() paravirt aware
MAINTAINERS: Update the ocores i2c bus driver maintainer, etc
blk-mq: remove duplicated definition of blk_mq_freeze_queue
Blk-iolatency: warn on negative inflight IO counter
blk-iolatency: fix IO hang due to negative inflight counter
MAINTAINERS: unify reference to xen-devel list
x86/mm/cpa: Fix set_mce_nospec()
futex: Handle early deadlock return correctly
futex: Fix barrier comment
net: dsa: b53: Fix for failure when irq is not defined in dt
blktrace: Show requests without sector
mips: cm: reprime error cause
mips: loongson64: remove unreachable(), fix loongson_poweroff().
sit: check if IPv6 enabled before calling ip6_err_gen_icmpv6_unreach()
geneve: should not call rt6_lookup() when ipv6 was disabled
KVM: nVMX: unconditionally cancel preemption timer in free_nested (CVE-2019-7221)
KVM: x86: work around leak of uninitialized stack contents (CVE-2019-7222)
kvm: fix kvm_ioctl_create_device() reference counting (CVE-2019-6974)
signal: Better detection of synchronous signals
...
If a controller supports the NS Change Notification, the namespace
scan_work is automatically triggered after attaching a new namespace.
Occasionally the namespace scan_work may append the new namespace to the
list before the admin command effects handling is completed. The effects
handling unfreezes namespaces, but if it unfreezes the newly attached
namespace, its request_queue freeze depth will be off and we'll hit the
warning in blk_mq_unfreeze_queue().
On the next namespace add, we will fail to freeze that queue due to the
previous bad accounting and deadlock waiting for frozen.
Fix that by preventing scan work from altering the namespace list while
command effects handling needs to pair freeze with unfreeze.
Reported-by: Wen Xiong <wenxiong@us.ibm.com>
Tested-by: Wen Xiong <wenxiong@us.ibm.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
It is used now just to flush error recovery and reconnect work items in
the RDMA and TCP transports, which can simply be moved to the
corresponding teardown routines.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
If a device provides an NQN it is expected to be globally unique.
Unfortunately some firmware revisions for Intel 760p/Pro 7600p devices did
not satisfy this requirement. In these circumstances if a system has >1
affected device then only one device is enabled. If this quirk is enabled
then the device supplied subnqn is ignored and we fallback to generating
one as if the field was empty. In this case we also suppress the version
check so we don't print a warning when the quirk is enabled.
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: James Dingwall <james@dingwall.me.uk>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Pass poll bool to indicate that we need it to poll. This prepares us for
polling support in nvmf since connect is an I/O that will be queued
and has to be polled in order to complete. If poll is passed,
we call nvme_execute_rq_polled which sends the requests and polls
for its completion.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When boxes are run near (or to) OOM, we have a problem with the discard
page allocation in nvme. If we fail allocating the special page, we
return busy, and it'll get retried. But since ordering is honored for
dispatch requests, we can keep retrying this same IO and failing. Behind
that IO could be requests that want to free memory, but they never get
the chance.
Allocate a fixed discard page per controller for a safe fallback, and use
that if the initial allocation fails.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add __exit annotation to cleanup helper which is only
called once in the module.
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Currently the geometry of an OCSSD is enumerated using a two step
approach:
First, nvm_register is called, the OCSSD identify command is issued,
and second the geometry sos and csecs values are read either from the
OCSSD identify if it is a 1.2 drive, or from the NVMe namespace data
structure if it is a 2.0 device.
This patch recombines it into a single step, such that nvm_register can
use the csecs and sos fields independent of which version is used. This
enables one to dynamically size the lightnvm subsystem dma pool.
Reviewed-by: Igor Konopko <igor.j.konopko@intel.com>
Reviewed-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A controller may have an internal state that is not able to successfully
process commands for a short duration. In such states, an immediate
command requeue is expected to fail. The driver may exceed its max
retry count, which permanently ends the command in failure when the same
command would succeed after waiting for the controller to be ready.
NVMe ratified TP 4033 provides a delay hint in the completion status
code for failed commands. Implement the retry delay based on the command
completion status and the controller's requested delay.
Note that requeued commands are handled per request_queue, not per
individual request. If multiple commands fail, the controller should
consistently report the desired delay time for retryable commands in
all CQEs, otherwise the requeue list may be kicked too soon.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If the controller supports traffic based keep alive, we restart the keep
alive timer if any admin or io commands was completed during the kato
period. This prevents a possible starvation of keep alive commands in
the presence of heavy traffic as in such case, we already have a health
indication from the host perspective.
Only set a comp_seen indicator in case the controller supports keep
alive to minimize the overhead for pci controllers.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We get the controller attributes in identify, cache them as we'll need
them for traffic based keep alive support.
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Instead of directly poking into the struct device add a new numa_node
field to struct nvme_ctrl. This allows fabrics drivers where ctrl->dev
is a virtual device to support NUMA affinity as well.
Also expose the field as a sysfs attribute, and populate it for the
RDMA and FC transports.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlwEZdIeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGAlQH/19oax2Za3IPqF4X
DM3lal5M6zlUVkoYstqzpbR3MqUwgEnMfvoeMDC6mI9N4/+r2LkV7cRR8HzqQCCS
jDfD69IzRGb52VSeJmbOrkxBWsR1Nn0t4Z3rEeLPxwaOoNpRc8H973MbAQ2FKMpY
S4Y3jIK1dNiRRxdh52NupVkQF+djAUwkBuVk/rrvRJmTDij4la03cuCDAO+Di9lt
GHlVvygKw2SJhDR+z3ArwZNmE0ceCcE6+W7zPHzj2KeWuKrZg22kfUD454f2YEIw
FG0hu9qecgtpYCkLSm2vr4jQzmpsDoyq3ZfwhjGrP4qtvPC3Db3vL3dbQnkzUcJu
JtwhVCE=
=O1q1
-----END PGP SIGNATURE-----
Merge tag 'v4.20-rc5' into for-4.21/block
Pull in v4.20-rc5, solving a conflict we'll otherwise get in aio.c and
also getting the merge fix that went into mainline that users are
hitting testing for-4.21/block and/or for-next.
* tag 'v4.20-rc5': (664 commits)
Linux 4.20-rc5
PCI: Fix incorrect value returned from pcie_get_speed_cap()
MAINTAINERS: Update linux-mips mailing list address
ocfs2: fix potential use after free
mm/khugepaged: fix the xas_create_range() error path
mm/khugepaged: collapse_shmem() do not crash on Compound
mm/khugepaged: collapse_shmem() without freezing new_page
mm/khugepaged: minor reorderings in collapse_shmem()
mm/khugepaged: collapse_shmem() remember to clear holes
mm/khugepaged: fix crashes due to misaccounted holes
mm/khugepaged: collapse_shmem() stop if punched or truncated
mm/huge_memory: fix lockdep complaint on 32-bit i_size_read()
mm/huge_memory: splitting set mapping+index before unfreeze
mm/huge_memory: rename freeze_page() to unmap_page()
initramfs: clean old path before creating a hardlink
kernel/kcov.c: mark funcs in __sanitizer_cov_trace_pc() as notrace
psi: make disabling/enabling easier for vendor kernels
proc: fixup map_files test on arm
debugobjects: avoid recursive calls with kmemleak
userfaultfd: shmem: UFFDIO_COPY: set the page dirty if VM_WRITE is not set
...
Without CONFIG_NVME_MULTIPATH enabled a multi-port subsystem might
show up as invididual devices and cause problems, warn about it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
We have this functionality in sbitmap, but we don't export it in
blk-mq for users of the tags busy iteration. This can be useful
for stopping the iteration, if the caller doesn't need to find
more requests.
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=58I4
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Fix ASPM link_state teardown on removal (Lukas Wunner)
- Fix misleading _OSC ASPM message (Sinan Kaya)
- Make _OSC optional for PCI (Sinan Kaya)
- Don't initialize ASPM link state when ACPI_FADT_NO_ASPM is set
(Patrick Talbert)
- Remove x86 and arm64 node-local allocation for host bridge structures
(Punit Agrawal)
- Pay attention to device-specific _PXM node values (Jonathan Cameron)
- Support new Immediate Readiness bit (Felipe Balbi)
- Differentiate between pciehp surprise and safe removal (Lukas Wunner)
- Remove unnecessary pciehp includes (Lukas Wunner)
- Drop pciehp hotplug_slot_ops wrappers (Lukas Wunner)
- Tolerate PCIe Slot Presence Detect being hardwired to zero to
workaround broken hardware, e.g., the Wilocity switch/wireless device
(Lukas Wunner)
- Unify pciehp controller & slot structs (Lukas Wunner)
- Constify hotplug_slot_ops (Lukas Wunner)
- Drop hotplug_slot_info (Lukas Wunner)
- Embed hotplug_slot struct into users instead of allocating it
separately (Lukas Wunner)
- Initialize PCIe port service drivers directly instead of relying on
initcall ordering (Keith Busch)
- Restore PCI config state after a slot reset (Keith Busch)
- Save/restore DPC config state along with other PCI config state
(Keith Busch)
- Reference count devices during AER handling to avoid race issue with
concurrent hot removal (Keith Busch)
- If an Upstream Port reports ERR_FATAL, don't try to read the Port's
config space because it is probably unreachable (Keith Busch)
- During error handling, use slot-specific reset instead of secondary
bus reset to avoid link up/down issues on hotplug ports (Keith Busch)
- Restore previous AER/DPC handling that does not remove and
re-enumerate devices on ERR_FATAL (Keith Busch)
- Notify all drivers that may be affected by error recovery resets
(Keith Busch)
- Always generate error recovery uevents, even if a driver doesn't have
error callbacks (Keith Busch)
- Make PCIe link active reporting detection generic (Keith Busch)
- Support D3cold in PCIe hierarchies during system sleep and runtime,
including hotplug and Thunderbolt ports (Mika Westerberg)
- Handle hpmemsize/hpiosize kernel parameters uniformly, whether slots
are empty or occupied (Jon Derrick)
- Remove duplicated include from pci/pcie/err.c and unused variable
from cpqphp (YueHaibing)
- Remove driver pci_cleanup_aer_uncorrect_error_status() calls (Oza
Pawandeep)
- Uninline PCI bus accessors for better ftracing (Keith Busch)
- Remove unused AER Root Port .error_resume method (Keith Busch)
- Use kfifo in AER instead of a local version (Keith Busch)
- Use threaded IRQ in AER bottom half (Keith Busch)
- Use managed resources in AER core (Keith Busch)
- Reuse pcie_port_find_device() for AER injection (Keith Busch)
- Abstract AER interrupt handling to disconnect error injection (Keith
Busch)
- Refactor AER injection callbacks to simplify future improvments
(Keith Busch)
- Remove unused Netronome NFP32xx Device IDs (Jakub Kicinski)
- Use bitmap_zalloc() for dma_alias_mask (Andy Shevchenko)
- Add switch fall-through annotations (Gustavo A. R. Silva)
- Remove unused Switchtec quirk variable (Joshua Abraham)
- Fix pci.c kernel-doc warning (Randy Dunlap)
- Remove trivial PCI wrappers for DMA APIs (Christoph Hellwig)
- Add Intel GPU device IDs to spurious interrupt quirk (Bin Meng)
- Run Switchtec DMA aliasing quirk only on NTB endpoints to avoid
useless dmesg errors (Logan Gunthorpe)
- Update Switchtec NTB documentation (Wesley Yung)
- Remove redundant "default n" from Kconfig (Bartlomiej Zolnierkiewicz)
- Avoid panic when drivers enable MSI/MSI-X twice (Tonghao Zhang)
- Add PCI support for peer-to-peer DMA (Logan Gunthorpe)
- Add sysfs group for PCI peer-to-peer memory statistics (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA scatterlist mapping interface (Logan
Gunthorpe)
- Add PCI configfs/sysfs helpers for use by peer-to-peer users (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA driver writer's documentation (Logan
Gunthorpe)
- Add block layer flag to indicate driver support for PCI peer-to-peer
DMA (Logan Gunthorpe)
- Map Infiniband scatterlists for peer-to-peer DMA if they contain P2P
memory (Logan Gunthorpe)
- Register nvme-pci CMB buffer as PCI peer-to-peer memory (Logan
Gunthorpe)
- Add nvme-pci support for PCI peer-to-peer memory in requests (Logan
Gunthorpe)
- Use PCI peer-to-peer memory in nvme (Stephen Bates, Steve Wise,
Christoph Hellwig, Logan Gunthorpe)
- Cache VF config space size to optimize enumeration of many VFs
(KarimAllah Ahmed)
- Remove unnecessary <linux/pci-ats.h> include (Bjorn Helgaas)
- Fix VMD AERSID quirk Device ID matching (Jon Derrick)
- Fix Cadence PHY handling during probe (Alan Douglas)
- Signal Cadence Endpoint interrupts via AXI region 0 instead of last
region (Alan Douglas)
- Write Cadence Endpoint MSI interrupts with 32 bits of data (Alan
Douglas)
- Remove redundant controller tests for "device_type == pci" (Rob
Herring)
- Document R-Car E3 (R8A77990) bindings (Tho Vu)
- Add device tree support for R-Car r8a7744 (Biju Das)
- Drop unused mvebu PCIe capability code (Thomas Petazzoni)
- Add shared PCI bridge emulation code (Thomas Petazzoni)
- Convert mvebu to use shared PCI bridge emulation (Thomas Petazzoni)
- Add aardvark Root Port emulation (Thomas Petazzoni)
- Support 100MHz/200MHz refclocks for i.MX6 (Lucas Stach)
- Add initial power management for i.MX7 (Leonard Crestez)
- Add PME_Turn_Off support for i.MX7 (Leonard Crestez)
- Fix qcom runtime power management error handling (Bjorn Andersson)
- Update TI dra7xx unaligned access errata workaround for host mode as
well as endpoint mode (Vignesh R)
- Fix kirin section mismatch warning (Nathan Chancellor)
- Remove iproc PAXC slot check to allow VF support (Jitendra Bhivare)
- Quirk Keystone K2G to limit MRRS to 256 (Kishon Vijay Abraham I)
- Update Keystone to use MRRS quirk for host bridge instead of open
coding (Kishon Vijay Abraham I)
- Refactor Keystone link establishment (Kishon Vijay Abraham I)
- Simplify and speed up Keystone link training (Kishon Vijay Abraham I)
- Remove unused Keystone host_init argument (Kishon Vijay Abraham I)
- Merge Keystone driver files into one (Kishon Vijay Abraham I)
- Remove redundant Keystone platform_set_drvdata() (Kishon Vijay
Abraham I)
- Rename Keystone functions for uniformity (Kishon Vijay Abraham I)
- Add Keystone device control module DT binding (Kishon Vijay Abraham
I)
- Use SYSCON API to get Keystone control module device IDs (Kishon
Vijay Abraham I)
- Clean up Keystone PHY handling (Kishon Vijay Abraham I)
- Use runtime PM APIs to enable Keystone clock (Kishon Vijay Abraham I)
- Clean up Keystone config space access checks (Kishon Vijay Abraham I)
- Get Keystone outbound window count from DT (Kishon Vijay Abraham I)
- Clean up Keystone outbound window configuration (Kishon Vijay Abraham
I)
- Clean up Keystone DBI setup (Kishon Vijay Abraham I)
- Clean up Keystone ks_pcie_link_up() (Kishon Vijay Abraham I)
- Fix Keystone IRQ status checking (Kishon Vijay Abraham I)
- Add debug messages for all Keystone errors (Kishon Vijay Abraham I)
- Clean up Keystone includes and macros (Kishon Vijay Abraham I)
- Fix Mediatek unchecked return value from devm_pci_remap_iospace()
(Gustavo A. R. Silva)
- Fix Mediatek endpoint/port matching logic (Honghui Zhang)
- Change Mediatek Root Port Class Code to PCI_CLASS_BRIDGE_PCI (Honghui
Zhang)
- Remove redundant Mediatek PM domain check (Honghui Zhang)
- Convert Mediatek to pci_host_probe() (Honghui Zhang)
- Fix Mediatek MSI enablement (Honghui Zhang)
- Add Mediatek system PM support for MT2712 and MT7622 (Honghui Zhang)
- Add Mediatek loadable module support (Honghui Zhang)
- Detach VMD resources after stopping root bus to prevent orphan
resources (Jon Derrick)
- Convert pcitest build process to that used by other tools (iio, perf,
etc) (Gustavo Pimentel)
* tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (140 commits)
PCI/AER: Refactor error injection fallbacks
PCI/AER: Abstract AER interrupt handling
PCI/AER: Reuse existing pcie_port_find_device() interface
PCI/AER: Use managed resource allocations
PCI: pcie: Remove redundant 'default n' from Kconfig
PCI: aardvark: Implement emulated root PCI bridge config space
PCI: mvebu: Convert to PCI emulated bridge config space
PCI: mvebu: Drop unused PCI express capability code
PCI: Introduce PCI bridge emulated config space common logic
PCI: vmd: Detach resources after stopping root bus
nvmet: Optionally use PCI P2P memory
nvmet: Introduce helper functions to allocate and free request SGLs
nvme-pci: Add support for P2P memory in requests
nvme-pci: Use PCI p2pmem subsystem to manage the CMB
IB/core: Ensure we map P2P memory correctly in rdma_rw_ctx_[init|destroy]()
block: Add PCI P2P flag for request queue
PCI/P2PDMA: Add P2P DMA driver writer's documentation
docs-rst: Add a new directory for PCI documentation
PCI/P2PDMA: Introduce configfs/sysfs enable attribute helpers
PCI/P2PDMA: Add PCI p2pmem DMA mappings to adjust the bus offset
...
For P2P requests, we must use the pci_p2pmem_map_sg() function instead of
the dma_map_sg functions.
With that, we can then indicate PCI_P2P support in the request queue. For
this, we create an NVME_F_PCI_P2P flag which tells the core to set
QUEUE_FLAG_PCI_P2P in the request queue.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Israel Rukshin