Fix missing mutex_destroy() when probe fails and
when driver is removed.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix The camera has a blurry screen phenomenon when
we video chat with apprtc using vp9 codec
Signed-off-by: Tiffany Lin <tiffany.lin@mediatek.com>
Reviewed-by: Wu-Cheng Li <wuchengli@chromium.org>
Tested-by: Wu-Cheng Li <wuchengli@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When devm_clk_get() fails the real error code should be propagated,
instead of always returning -EPROBE_DEFER.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
My eye fell on this wrong coefficient in the bt2020_full matrix.
The bt2020 matrix (limited range) is OK.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Set media_version to LINUX_VERSION_CODE, just as we did for
driver_version.
Nobody ever rememebers to update the version number, but
LINUX_VERSION_CODE will always be updated.
Move the MEDIA_API_VERSION define to the ifndef __KERNEL__ section of the
media.h header. That way kernelspace can't accidentally start to use
it again.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since the driver_version field in struct media_device is no longer
used, just remove it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This field will be removed as it is not needed anymore.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This field will be removed as it is not needed anymore.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't use driver_version from struct media_device, just return
LINUX_VERSION_CODE as the other media subsystems do.
The driver_version field in struct media_device will be removed
in the following patches.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver recently switched from handling page flip completion in the
DU vertical blanking handler to the VSP frame end handler to fix a race
condition. This unfortunately resulted in incorrect timestamps in the
vertical blanking events sent to userspace as vertical blanking is now
handled after sending the event.
To fix this we must reverse the order of the two operations. The easiest
way is to handle vertical blanking in the VSP frame end handler before
sending the event. The VSP frame end interrupt occurs approximately 50µs
earlier than the DU frame end interrupt, but this should not cause any
undue harm.
As we need to handle vertical blanking even when page flip completion is
delayed, the VSP driver now needs to call the frame end completion
callback unconditionally, with a new argument to report whether page
flip has completed.
With this new scheme the DU vertical blanking interrupt isn't needed
anymore, so we can stop enabling it.
Fixes: d503a43ac0 ("drm: rcar-du: Register a completion callback with VSP1")
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The VSP supports both header and headerless display lists. The latter is
easier to use when the VSP feeds data directly to the DU in continuous
mode, and the driver thus uses headerless display lists for DU operation
and header display lists otherwise.
Headerless display lists are only available on WPF.0. This has never
been an issue so far, as only WPF.0 is connected to the DU. However, on
H3 ES2.0, the VSP-DL instance has both WPF.0 and WPF.1 connected to the
DU. We thus can't use headerless display lists unconditionally for DU
operation.
Implement support for continuous mode with header display lists, and use
it for DU operation on WPF outputs that don't support headerless mode.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The R-Car H3 ES2.0 VSP-DL instance has two LIF entities and can drive
two display pipelines at the same time. Refactor the VSP DRM code to
support that by introducing a vsp_drm_pipeline object that models one
display pipeline.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The VSP2-DL instance (present in the H3 ES2.0 and M3-N SoCs) has two LIF
instances. Adapt the driver infrastructure to support multiple LIFs.
Support for multiple display pipelines will be added separately.
The change to the entity routing table removes the ability to connect
the LIF output to the HGO or HGT histogram generators. This feature is
only available on Gen2 hardware, isn't supported by the rest of the
driver, and has no known use case, so this isn't an issue.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
New Gen3 SoCs come with two new VSP2 variants names VSP2-BS and VSP2-DL,
as well as a new VSP2-D variant on V3M and V3H SoCs. Add new entries for
them in the VSP device info table.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The Blend/ROP Sub Unit (BRS) is a stripped-down version of the BRU found
in several VSP2 instances. Compared to a regular BRU, it supports two
inputs only, and thus has no ROP unit.
Add support for the BRS by modelling it as a new entity type, but reuse
the vsp1_bru object underneath. Chaining the BRU and BRS entities seems
to be supported by the hardware but isn't implemented yet as it isn't
the primary use case for the BRS.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In the H3 ES2.0 SoC the VSP2-DL instance has two connections to DU
channels that need to be configured independently. Extend the VSP-DU API
with a pipeline index to identify which pipeline the caller wants to
operate on.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When the VSP1 is used in a DRM pipeline the driver doesn't register the
media device. Links between entities are not exposed to userspace, but
are still used internally for the sole purpose of setting up internal
source to sink pointers through the link setup handler.
Instead of going through this complex procedure, remove link creation
and set the sink pointers directly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The internal VSP entity source and sink pointers are stored as
media_entity pointers, which are then cast to a vsp1_entity. As all
sources and sinks are vsp1_entity instances, we can store the
vsp1_entity pointers directly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The sink pointer is used to configure routing inside the VSP, and as
such must point to the next VSP entity in the pipeline. The WPF being a
pipeline terminal sink, its output route can't be configured. The
routing configuration code already handles this correctly without
referring to the sink pointer, which thus doesn't need to be set.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When the display start interrupt occurs, we know that the hardware has
finished loading the active display list. The driver then proceeds to
recycle the list, assuming it won't be needed anymore.
This assumption holds true for headerless display lists, as the VSP
doesn't reload the list for the next frame if it hasn't changed.
However, this isn't true anymore for header display lists, as they are
loaded at every frame start regardless of whether they have been
updated.
To prepare for header display lists usage in display pipelines, we need
to postpone recycling the list until it gets replaced by a new one
through a page flip. The driver already does so in the frame end
interrupt handler, so all we need is to skip list recycling in the
display start interrupt handler.
While the active list can be recycled at display start for headerless
display lists, there's no real harm in postponing that to the frame end
interrupt handler in all cases. This simplifies interrupt handling as we
don't need to process the display start interrupt anymore.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The display list headers are filled using information from the display
list only. Lower the display list manager spinlock contention by filling
the headers without holding the lock.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Disabling the BWB works around hangups observed while decoding. Since no
issues have been observed while encoding, and disabling BWB also reduces
encoding performance, reenable it for encoding.
Fixes: 89ed025d5c ("[media] coda: disable BWB for all codecs on CODA 960")
Reported-by: Ian Arkver <ian.arkver.dev@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Ian Arkver <ian.arkver.dev@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The gpiod API checks for NULL descriptors, so there is no need to
duplicate the check in the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The OMAP3 ISP supports both external and embedded BT.656 synchronization
for parallel buses. It currently gets the bus type information from the
source subdev through the .g_mbus_config() operation, but should instead
get it from DT as that's the authoritative source of bus configuration
information.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
None of the flash operations are mandatory and therefore there should be
no need for the flash ops structure either. Accept NULL.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The V4L2 flash class initialisation expects struct led_classdev_flash that
describes an indicator but only uses struct led_classdev which is a field
iled_cdev in the struct. Use struct iled_cdev only.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2_fwnode_endpoint_alloc_parse() is intended as a replacement for
v4l2_fwnode_endpoint_parse(). It parses the "link-frequency" property and
if the property isn't found, it returns an error. However,
"link-frequency" is an optional property and if it does not exist is not
an error. Instead, the number of link frequencies is simply zero in that
case.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
dev_pm_ops are not supposed to change at runtime. All functions
working with dev_pm_ops provided by <linux/device.h> work with
const dev_pm_ops. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
1195 376 0 1571 623 fimc-is-i2c.o
File size After adding 'const':
text data bss dec hex filename
1403 176 0 1579 62b fimc-is-i2c.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove unnecessary static on local variable rtype. Such variable
is initialized before being used, on every execution path throughout
the function. The static has no benefit and, removing it reduces
the code size.
This issue was detected using Coccinelle and the following semantic patch:
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
In the following log you can see the difference in the code size. Also,
there is a significant difference in the bss segment. This log is the
output of the size command, before and after the code change:
before:
text data bss dec hex filename
27765 5656 320 33741 83cd drivers/media/i2c/s5k5baf.o
after:
text data bss dec hex filename
27733 5600 256 33589 8335 drivers/media/i2c/s5k5baf.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On Exynos5420, the STREAM_STAT bit raised on the JPGINTST register means
there is a syntax error or an unrecoverable error on compressed file
when ERR_INT_EN is set to 1.
Fix this case and report BUF_STATE_ERROR to videobuf2.
Signed-off-by: Henry-Ruey Hsu <henryhsu@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds support for resolution change event to notify clients so
they can prepare correct output buffer. When resolution change happened,
G_FMT for CAPTURE should return old resolution and format before CAPTURE
queues streamoff.
This event is used in the Chromium browser project by the V4L2 JPEG
Decode Accelerator (V4L2JDA) to allocate output buffer.
Signed-off-by: Henry-Ruey Hsu <henryhsu@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds support for decoding 4:1:1 chroma subsampling in the
JPEG header parsing function.
Signed-off-by: Tony K Nadackal <tony.kn@samsung.com>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch moves the subsampling value decoding read from the JPEG
header into its own function. This new function is called
s5p_jpeg_subsampling_decode() and returns true if it successfully
decodes the subsampling value, false otherwise.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If s5p_jpeg_parse_hdr() fails to parse the JPEG header, the passed
s5p_jpeg_q_data structure is not modified so there is no need to use a
temporary structure and the field-by-field copy can be avoided.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch modifies the s5p_jpeg_parse_hdr() function so it only
modifies the passed s5p_jpeg_q_data structure if the jpeg header parsing
is successful.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Correct the WARN_ON statement for subsampling based on the
JPEG hardware version.
Signed-off-by: Tony K Nadackal <tony.kn@samsung.com>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When queuing an OUTPUT buffer for decoder, s5p_jpeg_parse_hdr()
function parses the input jpeg file and takes the width and height
parameters from its header. These new width/height values will be used
for the calculation of stride. HX_JPEG Hardware needs the width and
height values aligned on a 16 bits boundary. This width/height alignment
is handled in the s5p_jpeg_s_fmt_vid_cap() function during the S_FMT
ioctl call.
But if user space calls the QBUF of OUTPUT buffer after the S_FMT of
CAPTURE buffer, these aligned values will be replaced by the values in
jpeg header. If the width/height values of jpeg are not aligned, the
decoder output will be corrupted. So in this patch we call
jpeg_bound_align_image() to align the width/height values of Capture
buffer in s5p_jpeg_buf_queue().
Signed-off-by: Tony K Nadackal <tony.kn@samsung.com>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
drop VPFE_CMD_S_CCDC_RAW_PARAMS ioctl from dm355/dm644x following reasons:
- This ioctl was never in public api and was only defined in kernel header.
- The function set_params constantly mixes up pointers and phys_addr_t
numbers.
- This is part of a 'VPFE_CMD_S_CCDC_RAW_PARAMS' ioctl command that is
described as an 'experimental ioctl that will change in future kernels'.
- The code to allocate the table never gets called after we copy_from_user
the user input over the kernel settings, and then compare them
for inequality.
- We then go on to use an address provided by user space as both the
__user pointer for input and pass it through phys_to_virt to come up
with a kernel pointer to copy the data to. This looks like a trivially
exploitable root hole.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
this patch makes sure VPFE_CMD_S_CCDC_RAW_PARAMS ioctl no longer works
for vpfe_capture driver with a minimal patch suitable for backporting.
- This ioctl was never in public api and was only defined in kernel header.
- The function set_params constantly mixes up pointers and phys_addr_t
numbers.
- This is part of a 'VPFE_CMD_S_CCDC_RAW_PARAMS' ioctl command that is
described as an 'experimental ioctl that will change in future kernels'.
- The code to allocate the table never gets called after we copy_from_user
the user input over the kernel settings, and then compare them
for inequality.
- We then go on to use an address provided by user space as both the
__user pointer for input and pass it through phys_to_virt to come up
with a kernel pointer to copy the data to. This looks like a trivially
exploitable root hole.
Due to these reasons we make sure this ioctl now returns -EINVAL and backport
this patch as far as possible.
Fixes: 5f15fbb68f ("V4L/DVB (12251): v4l: dm644x ccdc module for vpfe capture driver")
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: <stable@vger.kernel.org> # for v3.7 and up
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In venus_boot(), we pass a pointer to a phys_addr_t
into dmam_alloc_coherent, which the compiler warns about:
platform/qcom/venus/firmware.c: In function 'venus_boot':
platform/qcom/venus/firmware.c:63:49: error: passing argument 3 of 'dmam_alloc_coherent' from incompatible pointer type [-Werror=incompatible-pointer-types]
To avoid the error refactor venus_boot function by discard
dma_alloc_coherent invocation because we don't want to map the
memory for the device. Something more, the usage of
DMA mapping API is actually wrong and the current
implementation relies on several bugs in DMA mapping code.
When these bugs are fixed that will break firmware loading,
so fix this now to avoid future troubles.
The meaning of venus_boot is to copy the content of the
firmware buffer into reserved (and memblock removed)
block of memory and pass that physical address to the
trusted zone for authentication and mapping through iommu
form the secure world. After iommu mapping is done the iova
is passed as ane entry point to the remote processor.
After this change memory-region property is parsed manually
and the physical address is memremap to CPU, call mdt_load to
load firmware segments into proper places and unmap
reserved memory.
Fixes: af2c3834c8 ("[media] media: venus: adding core part and helper functions")
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Not entirely sure what triggers it, but with venus build as kernel
module and in initrd, we hit this crash:
Unable to handle kernel paging request at virtual address ffff80003c039000
pgd = ffff00000a14f000
[ffff80003c039000] *pgd=00000000bd9f7003, *pud=00000000bd9f6003, *pmd=00000000bd9f0003, *pte=0000000000000000
Internal error: Oops: 96000007 [#1] SMP
Modules linked in: qcom_wcnss_pil(E+) crc32_ce(E) qcom_common(E) venus_core(E+) remoteproc(E) snd_soc_msm8916_digital(E) virtio_ring(E) cdc_ether(E) snd_soc_lpass_apq8016(E) snd_soc_lpass_cpu(E) snd_soc_apq8016_sbc(E) snd_soc_lpass_platform(E) v4l2_mem2mem(E) virtio(E) snd_soc_core(E) ac97_bus(E) snd_pcm_dmaengine(E) snd_seq(E) leds_gpio(E) videobuf2_v4l2(E) videobuf2_core(E) snd_seq_device(E) snd_pcm(E) videodev(E) media(E) nvmem_qfprom(E) msm(E) snd_timer(E) snd(E) soundcore(E) spi_qup(E) mdt_loader(E) qcom_tsens(E) qcom_spmi_temp_alarm(E) nvmem_core(E) msm_rng(E) uas(E) usb_storage(E) dm9601(E) usbnet(E) mii(E) mmc_block(E) adv7511(E) drm_kms_helper(E) syscopyarea(E) sysfillrect(E) sysimgblt(E) fb_sys_fops(E) qcom_spmi_vadc(E) qcom_vadc_common(PE) industrialio(E) pinctrl_spmi_mpp(E)
pinctrl_spmi_gpio(E) rtc_pm8xxx(E) clk_smd_rpm(E) sdhci_msm(E) sdhci_pltfm(E) qcom_smd_regulator(E) drm(E) smd_rpm(E) qcom_spmi_pmic(E) regmap_spmi(E) ci_hdrc_msm(E) ci_hdrc(E) usb3503(E) extcon_usb_gpio(E) phy_msm_usb(E) udc_core(E) qcom_hwspinlock(E) extcon_core(E) ehci_msm(E) i2c_qup(E) sdhci(E) mmc_core(E) spmi_pmic_arb(E) spmi(E) qcom_smd(E) smsm(E) rpmsg_core(E) smp2p(E) smem(E) hwspinlock_core(E) gpio_keys(E)
CPU: 2 PID: 551 Comm: irq/150-venus Tainted: P E 4.12.0+ #1625
Hardware name: qualcomm dragonboard410c/dragonboard410c, BIOS 2017.07-rc2-00144-ga97bdbdf72-dirty 07/08/2017
task: ffff800037338000 task.stack: ffff800038e00000
PC is at hfi_sys_init_done+0x64/0x140 [venus_core]
LR is at hfi_process_msg_packet+0xcc/0x1e8 [venus_core]
pc : [<ffff00000118b384>] lr : [<ffff00000118c11c>] pstate: 20400145
sp : ffff800038e03c60
x29: ffff800038e03c60 x28: 0000000000000000
x27: 00000000000df018 x26: ffff00000118f4d0
x25: 0000000000020003 x24: ffff80003a8d3010
x23: ffff00000118f760 x22: ffff800037b40028
x21: ffff8000382981f0 x20: ffff800037b40028
x19: ffff80003c039000 x18: 0000000000000020
x17: 0000000000000000 x16: ffff800037338000
x15: ffffffffffffffff x14: 0000001000000014
x13: 0000000100001007 x12: 0000000100000020
x11: 0000100e00000000 x10: 0000000000000001
x9 : 0000000200000000 x8 : 0000001400000001
x7 : 0000000000001010 x6 : 0000000000000148
x5 : 0000000000001009 x4 : ffff80003c039000
x3 : 00000000cd770abb x2 : 0000000000000042
x1 : 0000000000000788 x0 : 0000000000000002
Process irq/150-venus (pid: 551, stack limit = 0xffff800038e00000)
Call trace:
[<ffff00000118b384>] hfi_sys_init_done+0x64/0x140 [venus_core]
[<ffff00000118c11c>] hfi_process_msg_packet+0xcc/0x1e8 [venus_core]
[<ffff00000118a2b4>] venus_isr_thread+0x1b4/0x208 [venus_core]
[<ffff00000118e750>] hfi_isr_thread+0x28/0x38 [venus_core]
[<ffff000008161550>] irq_thread_fn+0x30/0x70
[<ffff0000081617fc>] irq_thread+0x14c/0x1c8
[<ffff000008105e68>] kthread+0x138/0x140
[<ffff000008083590>] ret_from_fork+0x10/0x40
Code: 52820125 52820207 7a431820 54000249 (b9400263)
---[ end trace c963460f20a984b6 ]---
The problem is that in the error case, we've incremented the data ptr
but not decremented rem_bytes, and keep reading (presumably garbage)
until eventually we go beyond the end of the buffer.
Instead, on first error, we should probably just bail out. Other
option is to increment read_bytes by sizeof(u32) before the switch,
rather than only accounting for the ptype header in the non-error
case. Note that in this case it is HFI_ERR_SYS_INVALID_PARAMETER,
ie. an unrecognized/unsupported parameter, so interpreting the next
word as a property type would be bogus. The other error cases are
due to truncated buffer, so there isn't likely to be anything valid
to interpret in the remainder of the buffer. So just bailing seems
like a reasonable solution.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If QCOM_MDT_LOADER is enabled, but ARCH_QCOM is not, we run into
a build error:
ERROR: "qcom_mdt_load" [drivers/media/platform/qcom/venus/venus-core.ko] undefined!
ERROR: "qcom_mdt_get_size" [drivers/media/platform/qcom/venus/venus-core.ko] undefined!
This changes the 'select' statement again, so we only try to enable
those symbols when the drivers will actually get built, and explicitly
test for QCOM_MDT_LOADER to be enabled before calling into it.
Fixes: 76724b30f2 ("[media] media: venus: enable building with COMPILE_TEST")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Without PM support, gcc warns about two unused functions:
platform/qcom/venus/core.c:146:13: error: 'venus_clks_disable' defined but not used [-Werror=unused-function]
platform/qcom/venus/core.c:126:12: error: 'venus_clks_enable' defined but not used [-Werror=unused-function]
The problem as usual are incorrect #ifdefs, so the easiest fix
is to do away with the #ifdef completely and mark the suspend/resume
handlers as __maybe_unused, which they are.
Fixes: af2c3834c8 ("[media] media: venus: adding core part and helper functions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Allow calling cec_notifier_set_phys_addr and
cec_notifier_set_phys_addr_from_edid with a NULL notifier, in which
case these functions do nothing.
Add a cec_notifier_phys_addr_invalidate helper function (the notifier
equivalent of cec_phys_addr_invalidate).
These changes simplify drm CEC driver support.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The persistent_config option is used to make the CEC settings persistent by using
the eeprom inside the device to store this information. This was on by default, which
caused confusion since this device now behaves differently from other CEC devices
which all come up unconfigured.
Another reason for doing this now is that I hope a more standard way of selecting
persistent configuration will be created in the future. And for that to work all
CEC drivers should behave the same and come up unconfigured by default.
None of the open source CEC applications are using this CEC framework at the moment
so change this behavior before it is too late.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.10 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The switch in cec_transmit_attempt_done() should ignore the
CEC_TX_STATUS_MAX_RETRIES status bit.
Calling this function with e.g. CEC_TX_STATUS_NACK | CEC_TX_STATUS_MAX_RETRIES
is perfectly legal and should not trigger the WARN(1).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since commit e8f4818895 ("[media] lirc: advertise
LIRC_CAN_GET_REC_RESOLUTION and improve") lircd uses the ioctl
LIRC_GET_REC_RESOLUTION to determine the shortest pulse or space that
the hardware can detect. This breaks decoding in lirc because lircd
expects the answer in microseconds, but nanoseconds is returned.
Cc: <stable@vger.kernel.org> # v2.6.36+
Reported-by: Derek <user.vdr@gmail.com>
Tested-by: Derek <user.vdr@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The vimc platform drivers define a platform device ID table but these
are not set to the .id_table field in the platform driver structure.
So the platform device ID table is only used to fill the aliases in
the module but are not used for matching (works because the platform
subsystem fallbacks to the driver's name if no .id_table is set).
But this also means that the platform device ID table isn't used if
the driver is built-in, which leads to the following build warning:
This causes the following build warnings when the driver is built-in:
drivers/media/platform/vimc//vimc-capture.c:528:40: warning: ‘vimc_cap_driver_ids’ defined but not used [-Wunused-const-variable=]
static const struct platform_device_id vimc_cap_driver_ids[] = {
^~~~~~~~~~~~~~~~~~~
drivers/media/platform/vimc//vimc-debayer.c:588:40: warning: ‘vimc_deb_driver_ids’ defined but not used [-Wunused-const-variable=]
static const struct platform_device_id vimc_deb_driver_ids[] = {
^~~~~~~~~~~~~~~~~~~
drivers/media/platform/vimc//vimc-scaler.c:442:40: warning: ‘vimc_sca_driver_ids’ defined but not used [-Wunused-const-variable=]
static const struct platform_device_id vimc_sca_driver_ids[] = {
^~~~~~~~~~~~~~~~~~~
drivers/media/platform/vimc//vimc-sensor.c:376:40: warning: ‘vimc_sen_driver_ids’ defined but not used [-Wunused-const-variable=]
static const struct platform_device_id vimc_sen_driver_ids[] = {
^~~~~~~~~~~~~~~~~~~
Reported-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Suggested-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix this kernel-doc warning:
WARNING: kernel-doc 'media-git/scripts/kernel-doc -rst -enable-lineno media-git/drivers/media/dvb-core/demux.h' processing failed with: 'ascii' codec can't decode byte 0xe2 in position 6368: ordinal
not in range(128)
Caused by using fancy quotes instead of regular quotes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The local pad parameter in media_entity_remote_pad() is not modified.
Make that explicit by adding a const modifier.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Declare v4l2_file_operations structures as const as they are only stored
in the fops field of video_device structures. This field is of type
const, so declare v4l2_file_operations structures with similar properties
as const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This function is used only internally. So, make it static.
Shuts up this warning:
drivers/media/v4l2-core/v4l2-fwnode.c:153:6: warning: no previous prototype for 'v4l2_fwnode_endpoint_parse_csi1_bus' [-Wmissing-prototypes]
void v4l2_fwnode_endpoint_parse_csi1_bus(struct fwnode_handle *fwnode,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
smatch produce this warning:
drivers/media/v4l2-core/v4l2-fwnode.c:76 v4l2_fwnode_endpoint_parse_csi_bus() error: buffer overflow 'array' 5 <= u16max
That's because, in thesis, the routine might have called with
some value at bus->num_data_lanes. That's not the current
case.
Yet, better to shut up this warning, and make the code more
reliable if some future changes might cause a bug.
While here, simplify the code a little bit by reading only
once from lanes-properties array.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As reported by this warning:
drivers/media/usb/pvrusb2/pvrusb2-encoder.c:263 pvr2_encoder_cmd() warn: continue to end of do { ... } while(0); loop
There's an issue at the retry logic there: the current logic is:
do {
if (need_to_retry)
continue;
some_code();
} while (0);
Well, that won't work, as continue will make it test for zero, and
abort the loop. So, change the loop to:
while (1) {
if (need_to_retry)
continue;
some_code();
break;
};
With seems to be what's actually expected there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is used just for printing a version number. As this is
never incremented, it makes no sense to keep it :-)
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
We seldomly increment version numbers on drivers, because... we
usually forget ;-)
So, instead, just make it identical to the Kernel version, as what
we do on all other drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Sylwester Nawrocki <snawrocki@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
drop VPFE_CMD_S_CCDC_RAW_PARAMS ioctl from dm355/dm644x following reasons:
- This ioctl was never in public api and was only defined in kernel header.
- The function set_params constantly mixes up pointers and phys_addr_t
numbers.
- This is part of a 'VPFE_CMD_S_CCDC_RAW_PARAMS' ioctl command that is
described as an 'experimental ioctl that will change in future kernels'.
- The code to allocate the table never gets called after we copy_from_user
the user input over the kernel settings, and then compare them
for inequality.
- We then go on to use an address provided by user space as both the
__user pointer for input and pass it through phys_to_virt to come up
with a kernel pointer to copy the data to. This looks like a trivially
exploitable root hole.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
this patch makes sure VPFE_CMD_S_CCDC_RAW_PARAMS ioctl no longer works
for vpfe_capture driver with a minimal patch suitable for backporting.
- This ioctl was never in public api and was only defined in kernel header.
- The function set_params constantly mixes up pointers and phys_addr_t
numbers.
- This is part of a 'VPFE_CMD_S_CCDC_RAW_PARAMS' ioctl command that is
described as an 'experimental ioctl that will change in future kernels'.
- The code to allocate the table never gets called after we copy_from_user
the user input over the kernel settings, and then compare them
for inequality.
- We then go on to use an address provided by user space as both the
__user pointer for input and pass it through phys_to_virt to come up
with a kernel pointer to copy the data to. This looks like a trivially
exploitable root hole.
Due to these reasons we make sure this ioctl now returns -EINVAL and backport
this patch as far as possible.
Fixes: 5f15fbb68f ("V4L/DVB (12251): v4l: dm644x ccdc module for vpfe capture driver")
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: <stable@vger.kernel.org> # for v3.7 and up
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In venus_boot(), we pass a pointer to a phys_addr_t
into dmam_alloc_coherent, which the compiler warns about:
platform/qcom/venus/firmware.c: In function 'venus_boot':
platform/qcom/venus/firmware.c:63:49: error: passing argument 3 of 'dmam_alloc_coherent' from incompatible pointer type [-Werror=incompatible-pointer-types]
To avoid the error refactor venus_boot function by discard
dma_alloc_coherent invocation because we don't want to map the
memory for the device. Something more, the usage of
DMA mapping API is actually wrong and the current
implementation relies on several bugs in DMA mapping code.
When these bugs are fixed that will break firmware loading,
so fix this now to avoid future troubles.
The meaning of venus_boot is to copy the content of the
firmware buffer into reserved (and memblock removed)
block of memory and pass that physical address to the
trusted zone for authentication and mapping through iommu
form the secure world. After iommu mapping is done the iova
is passed as ane entry point to the remote processor.
After this change memory-region property is parsed manually
and the physical address is memremap to CPU, call mdt_load to
load firmware segments into proper places and unmap
reserved memory.
Fixes: af2c3834c8 ("[media] media: venus: adding core part and helper functions")
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Not entirely sure what triggers it, but with venus build as kernel
module and in initrd, we hit this crash:
Unable to handle kernel paging request at virtual address ffff80003c039000
pgd = ffff00000a14f000
[ffff80003c039000] *pgd=00000000bd9f7003, *pud=00000000bd9f6003, *pmd=00000000bd9f0003, *pte=0000000000000000
Internal error: Oops: 96000007 [#1] SMP
Modules linked in: qcom_wcnss_pil(E+) crc32_ce(E) qcom_common(E) venus_core(E+) remoteproc(E) snd_soc_msm8916_digital(E) virtio_ring(E) cdc_ether(E) snd_soc_lpass_apq8016(E) snd_soc_lpass_cpu(E) snd_soc_apq8016_sbc(E) snd_soc_lpass_platform(E) v4l2_mem2mem(E) virtio(E) snd_soc_core(E) ac97_bus(E) snd_pcm_dmaengine(E) snd_seq(E) leds_gpio(E) videobuf2_v4l2(E) videobuf2_core(E) snd_seq_device(E) snd_pcm(E) videodev(E) media(E) nvmem_qfprom(E) msm(E) snd_timer(E) snd(E) soundcore(E) spi_qup(E) mdt_loader(E) qcom_tsens(E) qcom_spmi_temp_alarm(E) nvmem_core(E) msm_rng(E) uas(E) usb_storage(E) dm9601(E) usbnet(E) mii(E) mmc_block(E) adv7511(E) drm_kms_helper(E) syscopyarea(E) sysfillrect(E) sysimgblt(E) fb_sys_fops(E) qcom_spmi_vadc(E) qcom_vadc_common(PE) industrialio(E) pinctrl_spmi_mpp(E)
pinctrl_spmi_gpio(E) rtc_pm8xxx(E) clk_smd_rpm(E) sdhci_msm(E) sdhci_pltfm(E) qcom_smd_regulator(E) drm(E) smd_rpm(E) qcom_spmi_pmic(E) regmap_spmi(E) ci_hdrc_msm(E) ci_hdrc(E) usb3503(E) extcon_usb_gpio(E) phy_msm_usb(E) udc_core(E) qcom_hwspinlock(E) extcon_core(E) ehci_msm(E) i2c_qup(E) sdhci(E) mmc_core(E) spmi_pmic_arb(E) spmi(E) qcom_smd(E) smsm(E) rpmsg_core(E) smp2p(E) smem(E) hwspinlock_core(E) gpio_keys(E)
CPU: 2 PID: 551 Comm: irq/150-venus Tainted: P E 4.12.0+ #1625
Hardware name: qualcomm dragonboard410c/dragonboard410c, BIOS 2017.07-rc2-00144-ga97bdbdf72-dirty 07/08/2017
task: ffff800037338000 task.stack: ffff800038e00000
PC is at hfi_sys_init_done+0x64/0x140 [venus_core]
LR is at hfi_process_msg_packet+0xcc/0x1e8 [venus_core]
pc : [<ffff00000118b384>] lr : [<ffff00000118c11c>] pstate: 20400145
sp : ffff800038e03c60
x29: ffff800038e03c60 x28: 0000000000000000
x27: 00000000000df018 x26: ffff00000118f4d0
x25: 0000000000020003 x24: ffff80003a8d3010
x23: ffff00000118f760 x22: ffff800037b40028
x21: ffff8000382981f0 x20: ffff800037b40028
x19: ffff80003c039000 x18: 0000000000000020
x17: 0000000000000000 x16: ffff800037338000
x15: ffffffffffffffff x14: 0000001000000014
x13: 0000000100001007 x12: 0000000100000020
x11: 0000100e00000000 x10: 0000000000000001
x9 : 0000000200000000 x8 : 0000001400000001
x7 : 0000000000001010 x6 : 0000000000000148
x5 : 0000000000001009 x4 : ffff80003c039000
x3 : 00000000cd770abb x2 : 0000000000000042
x1 : 0000000000000788 x0 : 0000000000000002
Process irq/150-venus (pid: 551, stack limit = 0xffff800038e00000)
Call trace:
[<ffff00000118b384>] hfi_sys_init_done+0x64/0x140 [venus_core]
[<ffff00000118c11c>] hfi_process_msg_packet+0xcc/0x1e8 [venus_core]
[<ffff00000118a2b4>] venus_isr_thread+0x1b4/0x208 [venus_core]
[<ffff00000118e750>] hfi_isr_thread+0x28/0x38 [venus_core]
[<ffff000008161550>] irq_thread_fn+0x30/0x70
[<ffff0000081617fc>] irq_thread+0x14c/0x1c8
[<ffff000008105e68>] kthread+0x138/0x140
[<ffff000008083590>] ret_from_fork+0x10/0x40
Code: 52820125 52820207 7a431820 54000249 (b9400263)
---[ end trace c963460f20a984b6 ]---
The problem is that in the error case, we've incremented the data ptr
but not decremented rem_bytes, and keep reading (presumably garbage)
until eventually we go beyond the end of the buffer.
Instead, on first error, we should probably just bail out. Other
option is to increment read_bytes by sizeof(u32) before the switch,
rather than only accounting for the ptype header in the non-error
case. Note that in this case it is HFI_ERR_SYS_INVALID_PARAMETER,
ie. an unrecognized/unsupported parameter, so interpreting the next
word as a property type would be bogus. The other error cases are
due to truncated buffer, so there isn't likely to be anything valid
to interpret in the remainder of the buffer. So just bailing seems
like a reasonable solution.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If QCOM_MDT_LOADER is enabled, but ARCH_QCOM is not, we run into
a build error:
ERROR: "qcom_mdt_load" [drivers/media/platform/qcom/venus/venus-core.ko] undefined!
ERROR: "qcom_mdt_get_size" [drivers/media/platform/qcom/venus/venus-core.ko] undefined!
This changes the 'select' statement again, so we only try to enable
those symbols when the drivers will actually get built, and explicitly
test for QCOM_MDT_LOADER to be enabled before calling into it.
Fixes: 76724b30f2 ("[media] media: venus: enable building with COMPILE_TEST")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Without PM support, gcc warns about two unused functions:
platform/qcom/venus/core.c:146:13: error: 'venus_clks_disable' defined but not used [-Werror=unused-function]
platform/qcom/venus/core.c:126:12: error: 'venus_clks_enable' defined but not used [-Werror=unused-function]
The problem as usual are incorrect #ifdefs, so the easiest fix
is to do away with the #ifdef completely and mark the suspend/resume
handlers as __maybe_unused, which they are.
Fixes: af2c3834c8 ("[media] media: venus: adding core part and helper functions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As we're already touching on dvb_ca_en50221 to cleanup
checkpatch issues, do that also for its header file, with:
$ ./scripts/checkpatch.pl --strict --fix-inplace -f drivers/media/dvb-core/dvb_ca_en50221.h
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
- Running "checkpatch.pl -strict -f ..." gave more checks to fix.
* Blank lines aren't necessary after an open brace '{'
* Comparison to NULL written as "!<var>"
* CHECK: Blank lines aren't necessary before a close brace '}'
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some EXPORT_SYMBOL() on this file don't match the name of functions
that precedes them.
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fixed most of:
WARNING: line over 80 characters
The remaining lines are printk strings, which should not be split and
lines where I thing they should stay as they are.
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
- The STATUSREG_TXERR definition is not used and it has style
problems, too. Removing it seems to solve both issues.
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Used a helper variable "struct dvb_ca_slot *sl" instead of
"ca->slot_info[slot]". This reduces the line length and simplifies
code reading.
Fixed also "-strict" checks in this patch:
- Comparison to NULL written as "!<var>".
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fixed all:
ERROR: do not use assignment in if condition
Fixed also "-strict" checks in this patch:
- Changed "if (ret != 0)" to "if (ret)".
- Camel case variables have been converted to kernel_case.
- Comparison to NULL written as "!<var>".
- No space is necessary after a cast.
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fixed all:
WARNING: msleep < 20ms can sleep for up to 20ms
by using usleep_range.
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The CAM poll code for the budget-av is exactly the same on several
places. Extracting the code to a new function improves maintainability.
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Refactored "dvb_ca_en50221_thread" by moving the state machine into the
new function "dvb_ca_en50221_thread_state_machine". This reduces the
thread function size and reduces the structural complexity and of course
gives us more space to meet the line length goal in the new function.
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
While cab_state->state gives a quite accurate indication of the demod
signal status, it might be incorrect if cab_algo() wasn't able to
determine the exact status, with cab_algo() being the only place where
this status was updated from, and it is only called upon tuning to new
parameters passed to set_frontend(). Thus, the status will be wrong
until the demod is retuned. With the cab_signal_type parsing in
read_status(), this results in unusual fe_states like FE_HAS_SIGNAL |
FE_HAS_CARRIER | FE_HAS_LOCK, which, while userspace applications check
for FE_HAS_LOCK and work fine, leads to missing CNR or UCB stats.
Fix this by re-reading CAB_FSM_STATUS and updating cab_state->state() in
read_status(). While at it, refactor the fsm/qamfeclock and the
fsm->signaltype parsing into separate functions to make things cleaner
and deduplicate code. Also, assume full QAM FEC lock equals full
FE_STATUS.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Historically, mdev argument name was being used on both struct
media_device and struct media_devnode. Recently most occurrences of mdev
referring to struct media_devnode were replaced by devnode, which makes
more sense. Fix the last remaining occurrence.
Fixes: 163f1e93e9 ("[media] media-devnode: fix namespace mess")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Simplify the code to satisfy Linux coding style.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't populate array dib0090_tuning_table_cband_7090e_aci on the stack but
instead make it static. Makes the object code smaller by over 180 bytes:
Before:
text data bss dec hex filename
40052 7320 192 47564 b9cc dib0090.o
After:
text data bss dec hex filename
39780 7408 192 47380 b914 dib0090.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't populate const arrays on the stack but instead make them static.
Makes the object code smaller by over 1800 bytes:
Before:
text data bss dec hex filename
94100 9160 0 103260 1935c drxj.o
After:
text data bss dec hex filename
91044 10400 0 101444 18c44 drxj.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't populate arrays slowIncrDecLUT and fastIncrDecLUT on the stack but
instead make them static. Makes the object code smaller by over 100 bytes:
text data bss dec hex filename
27776 832 64 28672 7000 drxd_hard.o
text data bss dec hex filename
27530 976 64 28570 6f9a drxd_hard.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Discovered using w_scan when scanning DVB-T/T2: When w_scan goes from -T
to -T2, it does so without stopping the frontend using .sleep. Due to
this, the demod operation mode isn't re-setup, but as it still is in
STATE_ACTIVE_TC, PLP and T2 Profile are set up, but only retune_active()
is called, leaving the demod in T mode, thus not operable on any T2
frequency.
Fix this by putting the demod to sleep if priv->system isn't equal to
p->delsys. To properly accomplish this, sleep_tc() is split into
sleep_tc() and shutdown_tc(), where sleep_tc() will only perform the
sleep operation, while shutdown_tc() additionally performs the full
demod shutdown (to keep the behaviour when the .sleep FE_OP is called).
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't populate array gamma_par_mask on the stack but instead make it
static. Makes the object code smaller by 148 bytes:
Before:
text data bss dec hex filename
2993 1104 0 4097 1001 drivers/staging/fbtft/fb_st7789v.o
After:
text data bss dec hex filename
2757 1192 0 3949 f6d drivers/staging/fbtft/fb_st7789v.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't populate arrays on the stack but make them static. Makes
the object code smaller:
Before:
text data bss dec hex filename
89299 21704 64 111067 1b1db cxd2841er.o
After:
text data bss dec hex filename
85823 23432 64 109319 1ab07 cxd2841er.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When a user starts and stops filtering at a demux device too quickly
in a very short interval, the user process hangs in uninterruptible sleep,
due to an inconsistency of kthread status in the driver.
The kthread can be stopped before it starts running its thread function,
but the invocation status was partly managed in the kthread function,
which resulted in a double kthread_stop() of one kthread.
Signed-off-by: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Return 0 instead of -EINVAL in get_frontend if no demod mode is active.
This fixes ie. dvb-fe-tool getting confused and assuming a DVBv3 FE on idle
frontends when the FE has been put to sleep using sleep().
Also, in read_status(), don't immediately return when no demod is active,
so the remaining code has a chance to clear the signal statistics.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adds a stv0910_single modparm which, when set, configures the stv0910 to
run in single demodulator mode, currently intended for high bit rate
testing.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This adds all required glue code to support - in conjunction with the new
stv0910 and stv6111 demod/tuner drivers and additionally the lnbh25 LNB
controller driver - all current DVB-S/S2 hardware (bridges and flex
modules) from Digital Devices like the DD CineS2 V7 and V7A, current
S2 V4 DuoFlex modules, and probably all upcoming devices based on this
STV0910/STV6111/LNBH25 hardware stack.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The returned value is required for further evaluation of the exact
demodulator chip (stv090x or stv0910).
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This adds a frontend driver for the ST STV6111 DVB-S/S2 tuners. Like the
stv0910 demod frontend driver, this driver originates from the Digital
Devices' dddvb vendor driver package as of version 0.9.29, and was cleaned
up aswell. No functionality had to be removed though. Any camel case has
been converted to kernel_case, fixup patch has been proposed upstream.
Permission to reuse and mainline the driver code was formally granted by
Ralph Metzler <rjkm@metzlerbros.de>.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This was missing from the frontend_ops.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Original code at least has some signed/unsigned issues, resulting in
values like 32dBm. Implement signal strength readout to work without
asking the attached tuner, and use a lookup table instead of log calc.
Values reported appear plausible, gathered from feedback from several
testers.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Implements stream_id filter and scrambling code setup in start() and also
sets FE_CAN_MULTISTREAM in frontend_ops. This enables the driver to
properly receive and handle multistream transponders, functionality has
been reported working fine by testers with access to such streams, in
conjunction with VDR on the userspace side.
The code snippet originates from the original vendor's dddvb driver
package and has been made working properly with the current in-kernel
DVB core API.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fixes smatch error:
drivers/media/dvb-frontends/stv0910.c:715 dvbs2_nbch() error: buffer overflow 'nbch[fectype]' 2 <= 28
Also, fixes the nbch array table by adding the DUMMY_PLF element at the top
to match the enums (table element order was off by one before).
Patch sent upstream aswell.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This adds a multi frontend driver for the ST STV0910 DVB-S/S2 demodulator
frontends. The driver code originates from the Digital Devices' dddvb
vendor driver package as of version 0.9.29, and has been cleaned up from
core API usage which isn't supported yet in the kernel, and additionally
all obvious style issues have been resolved. All camel case and allcaps
have been converted to kernel_case and lowercase. Patches have been sent
to the vendor package maintainers to fix this aswell. Signal statistics
acquisition has been refactored to comply with standards.
Permission to reuse and mainline the driver code was formally granted by
Ralph Metzler <rjkm@metzlerbros.de>.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Now that the multiplexer framework is merged, drop the temporary
mmio-mux implementation from the video-mux driver and convert it to use
the multiplexer API.
[mchehab@s-opensource.com: fix a merge conflict at Kconfig]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
gcc-7 notices that we copy a fixed length string into another
string of the same size, with additional characters:
drivers/media/usb/usbvision/usbvision-i2c.c: In function 'usbvision_i2c_register':
drivers/media/usb/usbvision/usbvision-i2c.c:190:36: error: '%d' directive writing between 1 and 11 bytes into a region of size between 0 and 47 [-Werror=format-overflow=]
sprintf(usbvision->i2c_adap.name, "%s-%d-%s", i2c_adap_template.name,
^~~~~~~~~~
drivers/media/usb/usbvision/usbvision-i2c.c:190:2: note: 'sprintf' output between 4 and 76 bytes into a destination of size 48
Using snprintf() makes the code more robust in general, but will still
trigger a possible warning about truncation in the string.
We know this won't happen as the template name is always "usbvision", so
we can easily avoid the warning as well by using this as the format string
directly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch enables support for non-Bluecherry labeled solo6110
based PCI cards which have 3 x TW2864B chips and one TW2865.
These cards are displayed by lspci -nn as
"Softlogic Co., Ltd. SOLO6110 H.264 Video encoder/decoder [9413:6110]"
Bluecherry cards have 4 x TW2864A. According to datasheet register 0xFF
of TW2864B chips contains value 0x6A or 0x6B depending on revision
which being shifted 3 bits right gives value 0x0d.
Existing version of solo6x10 fails on these cards with
[276582.344942] solo6x10 0000:07:00.0: Probing Softlogic 6110
[276582.402151] solo6x10 0000:07:00.0: Could not initialize any techwell chips
[276582.402781] solo6x10: probe of 0000:07:00.0 failed with error -22
Signed-off-by: Anton Sviridenko <anton@corp.bluecherry.net>
Acked-by: Andrey Utkin <andrey_utkin@fastmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
drivers/media/i2c/adv748x/adv748x-csi2.c: In function 'adv748x_csi2_init_controls':
drivers/media/i2c/adv748x/adv748x-csi2.c:251:20: warning: variable 'ctrl' set but not used [-Wunused-but-set-variable]
struct v4l2_ctrl *ctrl;
^~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Provide support for the ADV7481 and ADV7482.
The driver is modelled with 4 subdevices to allow simultaneous streaming
from the AFE (Analog front end) and HDMI inputs though two CSI TX
entities.
The HDMI entity is linked to the TXA CSI bus, whilst the AFE is linked
to the TXB CSI bus.
The driver is based on a prototype by Koji Matsuoka in the Renesas BSP,
and an earlier rework by Niklas Söderlund.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Provides single source pad with up to 2592x1944 pixels at 10-bit raw
bayer format over MIPI CSI2 two lanes at 840Mbps/lane.
The driver supports following features:
- up to 30fps at 5M pixels
- manual exposure
- digital/analog gain
- V-blank/H-blank
- test pattern
- media controller
- runtime pm
[mchehab@s-opensource.com: fix a trivial merge conflict at Makefile]
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't populate const arrays on the stack but instead make them static.
Makes the object code smaller and saves nearly 550 bytes.
Before:
text data bss dec hex filename
3638 752 0 4390 1126 smiapp-quirk.o
After:
text data bss dec hex filename
2802 1040 0 3842 f02 smiapp-quirk.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add suport for standard integer menu V4L2_CID_LINK_FREQ control.
The CSI2 link frequency value is specific for each sensor mode so the
sensor mode structure is extended to add this. The control is made
read-only and its value is updated when the sensor mode is changed -
on set_format.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add suport for standard V4L2_CID_PIXEL_RATE control. The pixel clock
frequency value is specific for each sensor mode so the sensor mode
structure is extended to add this. The control is read-only and its
value is updated when the sensor mode is changed - on set_format.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Set media entity function to MEDIA_ENT_F_CAM_SENSOR.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If endpoint has an invalid configuration, ignore it instead of happily
proceeding to use it nonetheless. Ignoring such an endpoint is better than
failing since there could be multiple endpoints, only some of which are
bad.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If regulator returns -EPROBE_DEFER, we need to return it too, so that
omap3isp will be re-probed when regulator is ready.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
CSI-2 PHY power management is only needed for major version 15 of the ISP.
Additionally, set the CCP2 PHY for previous ISP versions as well.
These changes are necessary for CCP2 support.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The omap3isp driver extracts the CSI-2 lane configuration from the V4L2
fwnode endpoint but misses the number of lanes itself. Get this information
and use it in PHY configuration.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The CSI-2 phy driver did initialise mutexes in its init function but there
was no corresponding cleanup function destroying them. Fix that. Also
clean up ISP module initialisation a little.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check that we do have a valid port in an endpoint, return an error if not.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for CCP2 connected SMIA sensors as found
on the Nokia N900.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
CCP2 and CSI-1, are older single data lane serial busses.
[mchehab@s-opensource.com: don't use spaces for identation]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Just obtain it. It'll actually get used soon with CSI-1/CCP2.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The function to parse CSI2 bus parameters was called
v4l2_fwnode_endpoint_parse_csi_bus(), rename it as
v4l2_fwnode_endpoint_parse_csi2_bus() in anticipation of CSI1/CCP2
support.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If an encoder stop command is issued after the output queue has already
stopped streaming, the qsequence counter has been reset to 0. Always
wake up the capture queue if the output queue is not streaming.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Explicitly set MPEG-4 encoder class register instead of relying on the
default value of 0.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This fixes visual artifacts in the first macroblock row of encoded
MPEG-4 video output caused by 8 additional lines of luma data leaking
into the chroma planes of the internal reference framebuffers: the
buffer size is rounded up to a multiple of 16x16 macroblock size, same
as for the h.264 encoder.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Set the field of destination buffers properly.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
CodaDx6 only accepts GOP sizes up to 60 frames, but CODA960 can handle
up to 99 frames. If we disable automatic I frame generation altogether
by setting GOP size to 0, we can let an application produce arbitrarily
large I frame intervals using the V4L2_CID_MPEG_VIDEO_FORCE_KEY_FRAME
control.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This smatch warning:
coda/coda-common.c:706 coda_s_fmt() warn: missing break? reassigning 'ctx->tiled_map_type'
can be silenced by moving the ctx->tiled_map_type assignment into the
breakout condition. That way the field is not reassigned when falling
through to the next switch statement.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
CODA7541 supports H.264 BP level 3/3.1 and MPEG-4 SP level 5/6.
CODA960 supports H.264 BP level 4.0 and MPEG-4 SP level 5/6.
Implement the necessary profile and level controls to let userspace know
this.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix potential NULL pointer dereference in the error path of memory
allocation failure.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't populate the gain tables on the stack but make them static const.
Makes the object code smaller:
Before:
text data bss dec hex filename
7801 1408 0 9209 23f9 drivers/media/tuners/fc0012.o
8483 936 0 9419 24cb drivers/media/tuners/fc0013.o
After:
text data bss dec hex filename
7696 1464 0 9160 23c8 drivers/media/tuners/fc0012.o
8362 1024 0 9386 24aa drivers/media/tuners/fc0013.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't populate const array saa7128_regs_ntsc on the stack but insteaed make
it static. Makes the object code smaller and saves nearly 840 bytes
Before:
text data bss dec hex filename
9218 360 0 9578 256a solo6x10-tw28.o
After:
text data bss dec hex filename
8237 504 0 8741 2225 solo6x10-tw28.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Andrey Utkin <andrey_utkin@fastmail.com>
Signed-off-by: Ismael Luceno <ismael@iodev.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When CONFIG_V4L2 is built as a loadable module, the new video mux driver
fails to link as built-in code:
drivers/media/platform/video-mux.o: In function `video_mux_remove':
video-mux.c:(.text+0x24): undefined reference to `v4l2_async_unregister_subdev'
drivers/media/platform/video-mux.o: In function `video_mux_probe':
video-mux.c:(.text+0x800): undefined reference to `v4l2_subdev_init'
video-mux.c:(.text+0xa10): undefined reference to `v4l2_async_register_subdev'
This makes it use the same Kconfig dependency as all the other users of
the VIDEO_V4L2_SUBDEV_API symbol.
Fixes: 68803ad452 ("[media] platform: add video-multiplexer subdevice driver")
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for vb2_ops structures that are only stored in the ops field of a
vb2_queue structure. That field is declared const, so vb2_ops structures
that have this property can be declared as const also.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct vb2_ops i@p = { ... };
@ok@
identifier r.i;
struct vb2_queue e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct vb2_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct vb2_ops i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for vb2_ops structures that are only stored in the ops field of a
vb2_queue structure. That field is declared const, so vb2_ops structures
that have this property can be declared as const also.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct vb2_ops i@p = { ... };
@ok@
identifier r.i;
struct vb2_queue e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct vb2_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct vb2_ops i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for vb2_ops structures that are only stored in the ops field of a
vb2_queue structure. That field is declared const, so vb2_ops structures
that have this property can be declared as const also.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct vb2_ops i@p = { ... };
@ok@
identifier r.i;
struct vb2_queue e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct vb2_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct vb2_ops i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for vb2_ops structures that are only stored in the ops field of a
vb2_queue structure. That field is declared const, so vb2_ops structures
that have this property can be declared as const also.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct vb2_ops i@p = { ... };
@ok@
identifier r.i;
struct vb2_queue e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct vb2_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct vb2_ops i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for vb2_ops structures that are only stored in the ops field of a
vb2_queue structure. That field is declared const, so vb2_ops structures
that have this property can be declared as const also.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct vb2_ops i@p = { ... };
@ok@
identifier r.i;
struct vb2_queue e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct vb2_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct vb2_ops i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for vb2_ops structures that are only stored in the ops field of a
vb2_queue structure. That field is declared const, so vb2_ops structures
that have this property can be declared as const also.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct vb2_ops i@p = { ... };
@ok@
identifier r.i;
struct vb2_queue e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct vb2_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct vb2_ops i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for vb2_ops structures that are only stored in the ops field of a
vb2_queue structure. That field is declared const, so vb2_ops structures
that have this property can be declared as const also.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct vb2_ops i@p = { ... };
@ok@
identifier r.i;
struct vb2_queue e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct vb2_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct vb2_ops i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for vb2_ops structures that are only stored in the ops field of a
vb2_queue structure. That field is declared const, so vb2_ops structures
that have this property can be declared as const also.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct vb2_ops i@p = { ... };
@ok@
identifier r.i;
struct vb2_queue e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct vb2_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct vb2_ops i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for vb2_ops structures that are only stored in the ops field of a
vb2_queue structure. That field is declared const, so vb2_ops structures
that have this property can be declared as const also.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct vb2_ops i@p = { ... };
@ok@
identifier r.i;
struct vb2_queue e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct vb2_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct vb2_ops i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove unnecessary static on local variable t_params.
Such variable is initialized before being used,
on every execution path throughout the function.
The static has no benefit and, removing it reduces
the code size.
This issue was detected using Coccinelle and the following semantic patch:
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
In the following log you can see the difference in the code size. Also,
there is a significant difference in the bss segment. This log is the
output of the size command, before and after the code change:
before:
text data bss dec hex filename
23314 3640 832 27786 6c8a drivers/media/tuners/tuner-simple.o
after:
text data bss dec hex filename
23257 3552 768 27577 6bb9 drivers/media/tuners/tuner-simple.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Trivial fix to spelling mistake in v4l2_dbg debug message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Trivial fix to spelling mistake in v4l2_info message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
dma_buf_ops are not supposed to change at runtime. All functions
working with dma_buf_ops provided by <linux/dma-buf.h> work with
const dma_buf_ops. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
5238 112 4 5354 14ea drivers/media/v4l2-core/videobuf2-dma-sg.o
File size After adding 'const':
text data bss dec hex filename
5358 0 4 5362 14f2 drivers/media/v4l2-core/videobuf2-dma-sg.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
dma_buf_ops are not supposed to change at runtime. All functions
working with dma_buf_ops provided by <linux/dma-buf.h> work with
const dma_buf_ops. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
3171 192 0 3363 d23 drivers/media/v4l2-core/videobuf2-vmalloc.o
File size After adding 'const':
text data bss dec hex filename
3291 80 0 3371 d2b drivers/media/v4l2-core/videobuf2-vmalloc.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
dma_buf_ops are not supposed to change at runtime. All functions
working with dma_buf_ops provided by <linux/dma-buf.h> work with
const dma_buf_ops. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
6035 272 0 6307 18a3 drivers/media/v4l2-core/videobuf2-dma-contig.o
File size After adding 'const':
text data bss dec hex filename
6155 160 0 6315 18ab drivers/media/v4l2-core/videobuf2-dma-contig.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Declare v4l2_file_operations structure as const as it is only stored
in the fops field of video_device structure. This field is of type
const, so declare v4l2_file_operations structures with similar properties
as const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Declare v4l2_file_operations structures as const as they are only stored
in the fops field of video_device structures. This field is of type
const, so declare v4l2_file_operations structures with similar properties
as const.
Cross compiled bfin_capture.o for blackfin arch. vpbe_display.o file did
not cross compile for arm. Could not find any architecture matching the
configuraion symbol for fsl-viu.c file.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The CEC adapter name used by the pulse8-cec and rainshadow-cec USB device drivers
was a fixed string, but it should be unique if you connect multiple of these devices
to the same computer.
Use dev_name(&serio->dev) instead, which make it unique again.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Especially the '0.10' version number is confusing since CEC_ADAP_G_CAPS
returns a completely different version number.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some hardware does more than one attempt. So when it calls
cec_transmit_done when an error occurred it will e.g. use an error count
of 2 instead of 1.
The framework always assumed a single attempt, but now it is smarter
and will sum the counters to detect how many attempts were made.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for CEC hardware that relies on low-level pin polling or
GPIO interrupts.
One example is the Allwinner SoC. But any GPIO-based CEC implementation can
use this as well.
A GPIO implementation is very suitable as well for debugging: it can use
interrupts to detect state changes and report it. Userspace can then verify
if the bus traffic is correct. This also makes error injection possible.
The disadvantage is that it is hard to get the timings right since linux
isn't a hard realtime system.
In general on an idle system it works quite well, but under load the timer
will miss its mark every so often.
The debugfs file /sys/kernel/debug/cec/cecX/status gives some statistics
with respect to the timer overruns.
When the adapter is unconfigured and the low-level driver supports
interrupts, then the interrupt will be used to detect changes. This should
be quite accurate. But when the adapter is configured a hrtimer has to be
used.
The hrtimer implements a state machine where for each state the code will
read the bus or drive the bus and go on to the next state. It will re-arm
the timer with a delay based on the next state.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for the new MONITOR_PIN mode.
Add the cec_pin_event function that the CEC pin code will call to queue pin
change events.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Event handling was always fairly simplistic since there were only
two events. With the addition of pin events this needed to be redesigned.
The state_change and lost_msgs events are now core events with the
guarantee that the last state is always available. The new pin events
are a queue of events (up to 64 for each event) and the oldest event
will be dropped if the application cannot keep up. Lost events are
marked with a new event flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is needed for CEC adapters that allocate resources that have
to be freed before the cec_adapter is deleted.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently the transmit_(attempt_)done and received_msg functions set
the timestamp themselves. For the upcoming low-level pin API we need
to pass this as an argument instead. So make _ts variants that allow
the caller to specify the timestamp.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Kernel logging messes up the upcoming low-level CEC monitoring support
which is very time-sensitive. So change the debug level of this message
but keep a counter that is shown in the debugfs status log.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The transmit code would increase the sequence number first thing, even though
CEC_TRANSMIT would return an error due to a malformatted cec_msg struct later
on.
While valid behavior, this had the disadvantage of producing holes in the
sequence list that made debugging harder.
Only increase the sequence number when the whole message is validated.
When debugging (i.e. with cec-ctl -M) the sequence numbering is now nicely
increasing by 1 per message.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The CEC version, vendor ID and OSD name were not cleared when clearing the
current set of logical addresses. This was unexpected and somewhat confusing,
so reset all these fields to their default values. Also document this since
the documentation wasn't quite clear either.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove the soc_camera dependencies and move the diver to i2c
Lost features, fortunately not used or not critical on test platform:
- soc_camera power on/off callback - replaced with clock enable/disable
only, no support for platform provided regulators nor power callback,
- soc_camera sense request - replaced with arbitrarily selected default
master clock rate and pixel clock limit, no support for platform
requested values,
- soc_camera board flags - no support for platform requested mbus config
tweaks.
Tested on Amstrad Delta with now out of tree but still locally
maintained omap1_camera host driver.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The vimc platform drivers define a platform device ID table but these
are not set to the .id_table field in the platform driver structure.
So the platform device ID table is only used to fill the aliases in
the module but are not used for matching (works because the platform
subsystem fallbacks to the driver's name if no .id_table is set).
But this also means that the platform device ID table isn't used if
the driver is built-in, which leads to the following build warning:
This causes the following build warnings when the driver is built-in:
drivers/media/platform/vimc//vimc-capture.c:528:40: warning: ‘vimc_cap_driver_ids’ defined but not used [-Wunused-const-variable=]
static const struct platform_device_id vimc_cap_driver_ids[] = {
^~~~~~~~~~~~~~~~~~~
drivers/media/platform/vimc//vimc-debayer.c:588:40: warning: ‘vimc_deb_driver_ids’ defined but not used [-Wunused-const-variable=]
static const struct platform_device_id vimc_deb_driver_ids[] = {
^~~~~~~~~~~~~~~~~~~
drivers/media/platform/vimc//vimc-scaler.c:442:40: warning: ‘vimc_sca_driver_ids’ defined but not used [-Wunused-const-variable=]
static const struct platform_device_id vimc_sca_driver_ids[] = {
^~~~~~~~~~~~~~~~~~~
drivers/media/platform/vimc//vimc-sensor.c:376:40: warning: ‘vimc_sen_driver_ids’ defined but not used [-Wunused-const-variable=]
static const struct platform_device_id vimc_sen_driver_ids[] = {
^~~~~~~~~~~~~~~~~~~
Reported-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Suggested-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Get rid of those two warnings:
drivers/media/platform/davinci/vpif_capture.c: In function 'vpif_remove':
drivers/media/platform/davinci/vpif_capture.c:1722:21: warning: variable 'common' set but not used [-Wunused-but-set-variable]
struct common_obj *common;
^~~~~~
drivers/media/platform/davinci/vpif_display.c: In function 'vpif_remove':
drivers/media/platform/davinci/vpif_display.c:1342:21: warning: variable 'common' set but not used [-Wunused-but-set-variable]
struct common_obj *common;
^~~~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZapWhAAoJEHm+PkMAQRiGKb0IAJM6b7SbWaw69Og7+qiFB+zZ
xp29iXqbE9fPISC6a5BRQV1ONjeDM6opGixGHqGC8Hla6k2IYz25VDNoF8wd0MXN
cz/Ih20vd3C5afxXGe5cTT8lsPAlV0mWXxForlu6j8jPeL62FPfq6RhEkw7AcrYL
yfYy3k3qSdOrrvBdII0WAAUi46UfIs+we9BQgbsMbkHOiqV2K0MOrzKE84Xbgepq
RAy2xg6P4b4+hTx8xTrYc1MXwpnqjRc0oJ08gdmiwW3AOOU7LxYFn7zDkLPWi9Rr
g4x6r4YhBTGxT4wNvovLIiqd9QFs//dMCuPWYwEtTICG48umIqqq24beQ0mvCdg=
=08Ic
-----END PGP SIGNATURE-----
Merge tag 'v4.13-rc1' into patchwork
Linux v4.13-rc1
* tag 'v4.13-rc1': (11136 commits)
Linux v4.13-rc1
random: reorder READ_ONCE() in get_random_uXX
random: suppress spammy warnings about unseeded randomness
replace incorrect strscpy use in FORTIFY_SOURCE
kmod: throttle kmod thread limit
kmod: add test driver to stress test the module loader
MAINTAINERS: give kmod some maintainer love
xtensa: use generic fb.h
fault-inject: add /proc/<pid>/fail-nth
fault-inject: simplify access check for fail-nth
fault-inject: make fail-nth read/write interface symmetric
fault-inject: parse as natural 1-based value for fail-nth write interface
fault-inject: automatically detect the number base for fail-nth write interface
kernel/watchdog.c: use better pr_fmt prefix
MAINTAINERS: move the befs tree to kernel.org
lib/atomic64_test.c: add a test that atomic64_inc_not_zero() returns an int
mm: fix overflow check in expand_upwards()
ubifs: Set double hash cookie also for RENAME_EXCHANGE
ubifs: Massage assert in ubifs_xattr_set() wrt. init_xattrs
ubifs: Don't leak kernel memory to the MTD
...
-----BEGIN PGP SIGNATURE-----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=2S5N
-----END PGP SIGNATURE-----
Merge tag 'drm-for-v4.13' of git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"This is the main pull request for the drm, I think I've got one later
driver pull for mediatek SoC driver, I'm undecided on if it needs to
go to you yet.
Otherwise summary below:
Core drm:
- Atomic add driver private objects
- Deprecate preclose hook in modern drivers
- MST bandwidth tracking
- Use kvmalloc in more places
- Add mode_valid hook for crtc/encoder/bridge
- Reduce sync_file construction time
- Documentation updates
- New DRM synchronisation object support
New drivers:
- pl111 - pl111 CLCD display controller
Panel:
- Innolux P079ZCA panel driver
- Add NL12880B20-05, NL192108AC18-02D, P320HVN03 panels
- panel-samsung-s6e3ha2: Add s6e3hf2 panel support
i915:
- SKL+ watermark fixes
- G4x/G33 reset improvements
- DP AUX backlight improvements
- Buffer based GuC/host communication
- New getparam for (sub)slice infomation
- Cannonlake and Coffeelake initial patches
- Execbuf optimisations
radeon/amdgpu:
- Lots of Vega10 bug fixes
- Preliminary raven support
- KIQ support for compute rings
- MEC queue management rework
- DCE6 Audio support
- SR-IOV improvements
- Better radeon/amdgpu selection support
nouveau:
- HDMI stereoscopic support
- Display code rework for >= GM20x GPUs
msm:
- GEM rework for fine-grained locking
- Per-process pagetable work
- HDMI fixes for Snapdragon 820.
vc4:
- Remove 256MB CMA limit from vc4
- Add out-fence support
- Add support for cygnus
- Get/set tiling ioctls support
- Add T-format tiling support for scanout
zte:
- add VGA support.
etnaviv:
- Thermal throttle support for newer GPUs
- Restore userspace buffer cache performance
- dma-buf sync fix
stm:
- add stm32f429 display support
exynos:
- Rework vblank handling
- Fixup sw-trigger code
sun4i:
- V3s display engine support
- HDMI support for older SoCs
- Preliminary work on dual-pipeline SoCs.
rcar-du:
- VSP work
imx-drm:
- Remove counter load enable from PRE
- Double read/write reduction flag support
tegra:
- Documentation for the host1x and drm driver.
- Lots of staging ioctl fixes due to grate project work.
omapdrm:
- dma-buf fence support
- TILER rotation fixes"
* tag 'drm-for-v4.13' of git://people.freedesktop.org/~airlied/linux: (1270 commits)
drm: Remove unused drm_file parameter to drm_syncobj_replace_fence()
drm/amd/powerplay: fix bug fail to remove sysfs when rmmod amdgpu.
amdgpu: Set cik/si_support to 1 by default if radeon isn't built
drm/amdgpu/gfx9: fix driver reload with KIQ
drm/amdgpu/gfx8: fix driver reload with KIQ
drm/amdgpu: Don't call amd_powerplay_destroy() if we don't have powerplay
drm/ttm: Fix use-after-free in ttm_bo_clean_mm
drm/amd/amdgpu: move get memory type function from early init to sw init
drm/amdgpu/cgs: always set reference clock in mode_info
drm/amdgpu: fix vblank_time when displays are off
drm/amd/powerplay: power value format change for Vega10
drm/amdgpu/gfx9: support the amdgpu.disable_cu option
drm/amd/powerplay: change PPSMC_MSG_GetCurrPkgPwr for Vega10
drm/amdgpu: Make amdgpu_cs_parser_init static (v2)
drm/amdgpu/cs: fix a typo in a comment
drm/amdgpu: Fix the exported always on CU bitmap
drm/amdgpu/gfx9: gfx_v9_0_enable_gfx_static_mg_power_gating() can be static
drm/amdgpu/psp: upper_32_bits/lower_32_bits for address setup
drm/amd/powerplay/cz: print message if smc message fails
drm/amdgpu: fix typo in amdgpu_debugfs_test_ib_init
...
-----BEGIN PGP SIGNATURE-----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=RtxO
-----END PGP SIGNATURE-----
Merge tag 'media/v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- addition of fwnode support at V4L2 core
- addition of a few more SDR formats
- new imx driver to support i.MX6 cameras
- new driver for Qualcon venus codecs
- new I2C sensor drivers: dw9714, max2175, ov13858, ov5640
- new CEC driver: stm32-cec
- some improvements to DVB frontend documentation and a few fixups
- several driver improvements and fixups
* tag 'media/v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (361 commits)
[media] media: entity: Catch unbalanced media_pipeline_stop calls
[media] media/uapi/v4l: clarify cropcap/crop/selection behavior
[media] v4l2-ioctl/exynos: fix G/S_SELECTION's type handling
[media] vimc: sen: Declare vimc_sen_video_ops as static
[media] vimc: sca: Add scaler
[media] vimc: deb: Add debayer filter
[media] vimc: Subdevices as modules
[media] vimc: cap: Support several image formats
[media] vimc: sen: Support several image formats
[media] vimc: common: Add vimc_colorimetry_clamp
[media] vimc: common: Add vimc_link_validate
[media] vimc: common: Add vimc_pipeline_s_stream helper
[media] vimc: common: Add vimc_ent_sd_* helper
[media] vimc: Move common code from the core
[media] vimc: sen: Integrate the tpg on the sensor
[media] media: i2c: ov772x: Force use of SCCB protocol
[media] dvb uapi docs: enums are passed by value, not reference
[media] dvb: don't use 'time_t' in event ioctl
[media] media: venus: enable building with COMPILE_TEST
[media] af9013: refactor power control
...
This development cycle resulted in a fair amount of changes in both
core and driver sides. The most significant change in ALSA core is
about PCM. Also the support of of-graph card and the new DAPM widget
for DSP are noteworthy changes in ASoC core. And there're lots of
small changes splat over the tree, as you can see in diffstat.
Below are a few highlights:
ALSA core:
- Removal of set_fs() hackery from PCM core stuff, and the code
reorganization / optimization thereafter
- Improved support of PCM ack ops, and a new ABI for improved
control/status mmap handling
- Lots of constifications in various codes
ASoC core:
- The support of of-graph card, which may work as a better generic
device for a replacement of simple-card
- New widget types intended mainly for use with DSPs
ASoC drivers:
- New drivers for Allwinner V3s SoCs
- Ensonic ES8316 codec support
- More Intel SKL and KBL works
- More device support for Intel SST Atom (mostly for cheap tablets and
2-in-1 devices)
- Support for Rockchip PDM controllers
- Support for STM32 I2S and S/PDIF controllers
- Support for ZTE AUD96P22 codecs
HD-audio:
- Support of new Realtek codecs (ALC215/ALC285/ALC289), more quirks
for HP and Dell machines
- A few more fixes for i915 component binding
Note that of-graph change may bring the conflicts with a later pull
request of devicetree, as currently found in linux-next.
-----BEGIN PGP SIGNATURE-----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=PUEh
-----END PGP SIGNATURE-----
Merge tag 'sound-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This development cycle resulted in a fair amount of changes in both
core and driver sides. The most significant change in ALSA core is
about PCM. Also the support of of-graph card and the new DAPM widget
for DSP are noteworthy changes in ASoC core. And there're lots of
small changes splat over the tree, as you can see in diffstat.
Below are a few highlights:
ALSA core:
- Removal of set_fs() hackery from PCM core stuff, and the code
reorganization / optimization thereafter
- Improved support of PCM ack ops, and a new ABI for improved
control/status mmap handling
- Lots of constifications in various codes
ASoC core:
- The support of of-graph card, which may work as a better generic
device for a replacement of simple-card
- New widget types intended mainly for use with DSPs
ASoC drivers:
- New drivers for Allwinner V3s SoCs
- Ensonic ES8316 codec support
- More Intel SKL and KBL works
- More device support for Intel SST Atom (mostly for cheap tablets
and 2-in-1 devices)
- Support for Rockchip PDM controllers
- Support for STM32 I2S and S/PDIF controllers
- Support for ZTE AUD96P22 codecs
HD-audio:
- Support of new Realtek codecs (ALC215/ALC285/ALC289), more quirks
for HP and Dell machines
- A few more fixes for i915 component binding"
* tag 'sound-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (418 commits)
ALSA: hda - Fix unbalance of i915 module refcount
ASoC: Intel: Skylake: Remove driver debugfs exit
ASoC: Intel: Skylake: explicitly add the headers sst-dsp.h
ALSA: hda/realtek - Remove GPIO_MASK
ALSA: hda/realtek - Fix typo of pincfg for Dell quirk
ALSA: pcm: add a documentation for tracepoints
ALSA: atmel: ac97c: fix error return code in atmel_ac97c_probe()
ALSA: x86: fix error return code in hdmi_lpe_audio_probe()
ASoC: Intel: Skylake: Add support to read firmware registers
ASoC: Intel: Skylake: Add sram address to sst_addr structure
ASoC: Intel: Skylake: Debugfs facility to dump module config
ASoC: Intel: Skylake: Add debugfs support
ASoC: fix semicolon.cocci warnings
ASoC: rt5645: Add quirk override by module option
ASoC: rsnd: make arrays path and cmd_case static const
ASoC: audio-graph-card: add widgets and routing for external amplifier support
ASoC: audio-graph-card: update bindings for amplifier support
ASoC: rt5665: calibration should be done before jack detection
ASoC: rsnd: constify dev_pm_ops structures.
ASoC: nau8825: change crosstalk-bypass property to bool type
...
The big news with this release is the of-graph card, this provides a
replacement for simple-card that is much more flexibile and scalable,
allowing many more systems to use a generic sound card than was possible
before:
- The of-graph card, finally merged after a long and dedicated effort
by Morimoto-san.
- New widget types intended mainly for use with DSPs.
- New drivers for Allwinner V3s SoCs, Ensonic ES8316, several classes
of x86 machine, Rockchip PDM controllers, STM32 I2S and S/PDIF
controllers and ZTE AUD96P22 CODECs.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAllaa7wTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0MhRB/0cIuUi/SmMSGz7cNKdDDArdpxHUV0U
dJb6qqhXCKeDQcx/34b1m+BnZpeT9au4Nt8HxOlLRbumcnuesYqfeBeZvuJhsC4I
q3e8e+idQlOp3+WM+snUXhWM4P/UsA9H4BaV1jvYSQW/C9WhfuLxsOraRiebLH7u
WJkmfeVjpzHHWzfDtpWJLHVroRLLMbOaz0e0Pw8/R1dfof0u27zKknqHOUcwRg0N
4+IWvKn3p59VE6eM6QUmruMZZCCfn2Hv5RygWf3LaHVlhA28BZi0dyMMSSSzVG6o
Im1Wm5z0dmmTfQKdNDU3PPBEKG6amTqF+2uuXOsq1I7vuiT+akHZbgWW
=F5BP
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v4.13
The big news with this release is the of-graph card, this provides a
replacement for simple-card that is much more flexibile and scalable,
allowing many more systems to use a generic sound card than was possible
before:
- The of-graph card, finally merged after a long and dedicated effort
by Morimoto-san.
- New widget types intended mainly for use with DSPs.
- New drivers for Allwinner V3s SoCs, Ensonic ES8316, several classes
of x86 machine, Rockchip PDM controllers, STM32 I2S and S/PDIF
controllers and ZTE AUD96P22 CODECs.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZUGOmAAoJEHm+PkMAQRiGhX8H/3fIhingPD01MBf98U0xGrJo
yIXmhu6nFs7TM0lDVDcHsKgqLQIT69ll7PrSZrMkc1RGUIPINoCuJVuJqDre0kfB
of5TX2KegqSx8h1vOWjGBCBjdYfPGyMdf9icf6KsGc/SlIdhN6WA99kglAjJA0Ve
qPTNagF0ntUNg1lsXffxyfcHqFpyqw/Z/C4ie/byFsn9iJ1VG9mNlTWSud09vhuM
3tvHzTUVAIWWuRrrgrvgqQpnwL+q5BfSDsXScMjBau0EK3RGGqG8EN6Kbkfa7VQ6
aBoeboQjUijSJnVwvySdQ11MChTIOwZdfrNPra/1HD3WJNsSu4BIRt5JcAKcOhc=
=qmSg
-----END PGP SIGNATURE-----
Backmerge tag 'v4.12-rc7' into drm-next
Linux 4.12-rc7
Needed at least rc6 for drm-misc-next-fixes, may as well go to rc7
The buffer mode was already implemented in this driver, but it did not work
as expected. This has been fixed now, but it is still deactivated and can
be activated by removing a comment at the begin of the file.
Original code change by Ralph Metzler, modified by Jasmin Jessich and
Daniel Scheller to match Kernel code style.
Signed-off-by: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some lower level drivers may work better when sending blocks of data
instead byte per byte. For this we need new function pointers in the
dvb_ca_en50221 protocol structure (read_data, write_data) and the protocol
needs to execute them, if they are defined.
Block data transmission is done in all states except LINKINIT.
Original code change by Ralph Metzler, modified by Jasmin Jessich and
Daniel Scheller to match Kernel code style.
Signed-off-by: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some CAMs do a really slow initialization, which requires a longer timeout
for the first response.
Original code change by Ralph Metzler, modified by Jasmin Jessich to match
Kernel code style.
Signed-off-by: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In case of a linkinit failure change to state UNINITIALISED to re-init
the CAM.
Original code change by Ralph Metzler, modified by Jasmin Jessich to match
Kernel code style.
Signed-off-by: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The stv0367 driver provide a lot of status on its state machine.
Change the logic to provide more information about frontend locking
status. Also, while any detailed status isn't available, provide a more
complete FE_STATUS for DVB-T.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Provide QAM/DVB-C signal strength in decibel scale. Values returned from
stv0367cab_get_rf_lvl() are good but need to be multiplied as they're in
1dBm precision.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since the other statistics are read when fe_status conditions are TRUE,
change the ucblocks readout logic to match this aswell.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
While there's a test at the SNR calculus to avoid division by
zero, it will still follow the path that would do the division.
So, add a missing break there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add signal-to-noise-ratio as provided by the demodulator in decibel scale.
QAM/DVB-C needs some intlog calculation to have usable dB values, OFDM/
DVB-T values from the demod look alright already and are provided as-is.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When the demod driver puts the demod into sleep or shutdown state and it's
status is then polled e.g. via "dvb-fe-tool -m", i2c errors are printed
to the kernel log. If the last delsys was DVB-T/T2:
cxd2841er: i2c wr failed=-5 addr=6c reg=00 len=1
cxd2841er: i2c rd failed=-5 addr=6c reg=26
and if it was DVB-C:
cxd2841er: i2c wr failed=-5 addr=6c reg=00 len=1
cxd2841er: i2c rd failed=-5 addr=6c reg=49
This happens when read_status unconditionally calls into the
read_signal_strength() function which triggers the read_agc_gain_*()
functions, where these registered are polled.
This isn't a critical thing since when the demod is active again, no more
such errors are logged, however this might make users suspecting defects.
Fix this by requiring STATE_ACTIVE_* in priv->state. If it isn't in any
active state, additionally set the strength scale to NOT_AVAILABLE.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Value assigned to variable _type_ at line 678 is overwritten at line 688
before it can be used. This makes such variable assignment useless.
Remove this variable assignment and fix some coding style issues.
Addresses-Coverity-ID: 1226968
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The read_snr() functions currently do some magic to return relative scale
values when called. Split out register readouts into separate functions
so the functionality can be reused in some other way.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This adds the basics to stv0367ddb_read_status() to be able to properly
provide signal statistics in DVBv5 format. Also adds UCB readout and
provides those values. Also, don't return -EINVAL in ddb_read_status()
if active_demod_state indicates no delivery system.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use dev_dbg() in conjunction with the %*ph format macro to print the vmon
status debug, thus hiding continuous hexdumping from default log levels.
Also, change the attach success log line from error to info severity.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The semaphore 'i2c_switch_mutex' is used as a simple mutex, so
it should be written as one. Semaphores are going away in the future.
Signed-off-by: Binoy Jayan <binoy.jayan@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The semaphore 'stream_mutex' is used as a simple mutex, so
it should be written as one. Also moving the mutex_[lock/unlock]
to the caller as it is anyway locked at the beginning of the
callee thus avoiding repetition.
Signed-off-by: Binoy Jayan <binoy.jayan@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The semaphore 'cmd_mutex' is used as a simple mutex, so
it should be written as one. Also, replace down with
mutex_destroy to ensure sane state when ngene_stop is
called.
Signed-off-by: Binoy Jayan <binoy.jayan@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As such macro will check if the expression is true, it may fall through, as
warned:
In file included from ./include/uapi/linux/stddef.h:1:0,
from ./include/linux/stddef.h:4,
from ./include/uapi/linux/posix_types.h:4,
from ./include/uapi/linux/types.h:13,
from ./include/linux/types.h:5,
from ./drivers/media/dvb-core/dvb_frontend.h:35,
from drivers/media/tuners/fc0011.h:4,
from drivers/media/tuners/fc0011.c:20:
drivers/media/tuners/fc0011.c: In function 'fc0011_set_params':
./include/linux/compiler.h:179:22: warning: this statement may fall through [-Wimplicit-fallthrough=]
# define unlikely(x) __builtin_expect(!!(x), 0)
^~~~~~~~~~~~~~~~~~~~~~~~~~
./include/asm-generic/bug.h:109:2: note: in expansion of macro 'unlikely'
unlikely(__ret_warn_on); \
^~~~~~~~
drivers/media/tuners/fc0011.c:344:3: note: in expansion of macro 'WARN_ON'
WARN_ON(1);
^~~~~~~
drivers/media/tuners/fc0011.c:345:2: note: here
case 0:
^~~~
In file included from ./include/uapi/linux/stddef.h:1:0,
from ./include/linux/stddef.h:4,
from ./include/uapi/linux/posix_types.h:4,
from ./include/uapi/linux/types.h:13,
from ./include/linux/types.h:5,
from ./include/linux/list.h:4,
from ./include/linux/module.h:9,
from drivers/media/pci/tw5864/tw5864-video.c:17:
drivers/media/pci/tw5864/tw5864-video.c: In function 'tw5864_fmt_vid_cap':
./include/linux/compiler.h:179:22: warning: this statement may fall through [-Wimplicit-fallthrough=]
# define unlikely(x) __builtin_expect(!!(x), 0)
^~~~~~~~~~~~~~~~~~~~~~~~~~
./include/asm-generic/bug.h:68:2: note: in expansion of macro 'unlikely'
unlikely(__ret_warn_on); \
^~~~~~~~
drivers/media/pci/tw5864/tw5864-video.c:547:3: note: in expansion of macro 'WARN_ON_ONCE'
WARN_ON_ONCE(1);
^~~~~~~~~~~~
drivers/media/pci/tw5864/tw5864-video.c:548:2: note: here
case STD_NTSC:
^~~~
On both cases, it means an error, so, let's return an error
code, to make gcc happy.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Michael Büsch <m@bues.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
DRX_S9TOS16 and DRX_S24TODRXFREQ are simply not used. Furthermore,
sign_extend32() should be used for sign extension. (Also, the comment
describing DRX_S24TODRXFREQ was wrong). So remove these macros.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The dmaengine driver for sDMA now have support for interleaved transfer.
This trasnfer type was open coded with the legacy omap-dma API, but now
we can move it to dmaengine.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
While committing a change on em28xx, I got a warning of a
typo there. So, fix it on em28xx and on two other media drivers
with the same typo.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
While testing support for Terratec H6 rev. 2, it was noticed
that reading from eeprom there causes a timeout error.
Apparently, this is due to the need of properly setting GPIOs.
In any case, the driver doesn't really require eeprom reading
to succeed, as this is currently used only for debug.
So, Ignore such errors.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mostly this adds some unlocks to error paths. But, if you see where
there were "break;" statements before, I changed those paths to return
error codes instead of returning success.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch mostly adds unlocks to error paths. But one additional small
change is that I made the first "break;" a "goto unlock;" which means
that now we return failure instead of success on that path.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Values assigned to variables Fmax and Fmin at lines 2740 and 2741 are
overwritten at lines 2754 and 2755 before they can be used. This makes
such variable assignments useless.
Addresses-Coverity-ID: 1226952
Addresses-Coverity-ID: 1226953
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Side effect: KERN_DEBUG messages aren't written to the kernel log anymore.
This also improves the tda18212_ping reporting a bit so users know that if
pinging wasn't successful, bad things will happen.
Since in module_init_ddbridge() there's no dev yet, pr_info is used
instead.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Reported by smatch:
drivers/media/pci/ddbridge/ddbridge-core.c:1246 input_tasklet() warn: this loop depends on readl() succeeding
drivers/media/pci/ddbridge/ddbridge-core.c:1768 flashio() warn: this loop depends on readl() succeeding
drivers/media/pci/ddbridge/ddbridge-core.c:1788 flashio() warn: this loop depends on readl() succeeding
Fix this by introducing safe_ddbreadl() which will wrap ddbreadl and checks
for all bits set in the return which indicates failure, and return 0 in
that case. Usable as drop-in-replacement in all affected while loops w/o
having to change the logic.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
I would have liked the the picture run timeout error handler to be renamed to
something a bit more descriptive in the original commit fb2be08f8c ("[media]
coda: first step at error recovery").
Somehow v1 [1] was merged instead of v2 [2].
[1] https://patchwork.kernel.org/patch/9663965/
[2] https://patchwork.kernel.org/patch/9774239/
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The current pre-decrement is incorrect and should be replaced
with a post-decrement. Consider the case where the very first
clk_prepare_enable fails when i is 0; in this case the error
clean up will decrement the unsigned int which wraps to the
largest unsigned int value causing an array out of bounds read
on core->clks[i].
Detected by CoverityScan, CID#1446590 ("Out-of-bounds read")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check return value from call to core->write(), so in case of
error print error message, jump to goto label fail and eventually
return.
Addresses-Coverity-ID: 1226943
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Back in April I created a patch to address a false-positive warning:
drivers/media/usb/rainshadow-cec/rainshadow-cec.c: In function 'rain_irq_work_handler':
drivers/media/usb/rainshadow-cec/rainshadow-cec.c:171:31: error: 'data' may be used uninitialized in this function [-Werror=maybe-uninitialized]
My patch was totally wrong and introduced a real bug, and Colin Ian King thankfully
noticed it now and fixed my mistake. Unfortunately, fixing the actual uninitialized
data in this case brought back the original bogus warning.
This is a new version of the patch, which simplifies the code to the point where
gcc notices the behavior is correct.
Fixes: ca33784ba4 ("[media] rainshadow-cec: ensure exit_loop is intialized")
Fixes: ea6a69defd ("[media] rainshadow-cec: avoid -Wmaybe-uninitialized warning")
Cc: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Commit 680d87c0a9 ("[media] tuner-core: use pr_foo, instead of
internal printk macros") removed the use of PREFIX, remove the #define
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Convert STK_<LEVEL> to pr_<level> to use the typical kernel logging.
Add a define for pr_fmt. No change in logging output.
Miscellanea:
o Remove now unused PREFIX and STK_<LEVEL> macros
o Realign arguments
o Use pr_<level>_ratelimited
o Add a few missing newlines to formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This fixes a smatch warning:
drivers/media/platform/coda/coda-bit.c:415 coda_alloc_framebuffers()
error: we previously assumed 'ctx->codec' could be null (see line 396)
coda_alloc_framebuffers() is called from coda_start_encoding() and
__coda_start_decoding(). Both dereference ctx->codec before calling
coda_alloc_framebuffers() in lines 935 and 1649, so ctx->codec can not
be NULL.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This one got applied twice, causing a build error with clang:
drivers/media/i2c/et8ek8/et8ek8_driver.c:1499:1: error: redefinition of '__mod_of__et8ek8_of_table_device_table'
Fixes: 9ae05fd1e7 ("[media] et8ek8: Export OF device ID as module aliases")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Seven single characters (line breaks) should be put into a sequence.
Thus use the corresponding function "seq_putc".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Drivers must not perform unbalanced calls to stop the entity pipeline,
however if they do they will fault in the core media code, as the
entity->pipe will be set as NULL. We handle this gracefully in the core
with a WARN for the developer.
Replace the erroneous check on zero streaming counts, with a check on
NULL pipe elements instead, as this is the symptom of unbalanced
media_pipeline_stop calls.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pincharts@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The type field in struct v4l2_selection is supposed to never use the
_MPLANE variants. E.g. if the driver supports V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE,
then userspace should still pass V4L2_BUF_TYPE_VIDEO_CAPTURE.
The reasons for this are lost in the mists of time, but it is really
annoying. In addition, the exynos drivers didn't follow this rule and
instead expected the _MPLANE type.
To fix that code is added to the v4l2 core that maps the _MPLANE buffer
types to their regular equivalents before calling the driver.
Effectively this allows for userspace to use either _MPLANE or the regular
buffer type. This keeps backwards compatibility while making things easier
for userspace.
Since drivers now never see the _MPLANE buffer types the exynos drivers
had to be adapted as well.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Implement scaler and integrated with the core
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Implement the debayer filter and integrate it with the core
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Change the core structure for adding subdevices in the topology.
Instead of calling the specific create function for each subdevice,
inject a child platform_device with the driver's name.
Each type of node in the topology (sensor, capture, debayer, scaler)
will register a platform_driver with the corresponding name through the
component subsystem.
Implementing a new subdevice type doesn't require vimc-core to be altered.
This facilitates future implementation of dynamic entities, where
hotpluging an entity in the topology is just a matter of
registering/unregistering a platform_device in the system.
It also facilitates other implementations of different nodes without
touching the core code and remove the need of a header file for each
type of node.
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Allow user space to change the image format as the frame size, the
pixel format, colorspace, quantization, field YCbCr encoding
and the transfer function
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Allow user space to change the image format as the frame size, the
media bus pixel format, colorspace, quantization, field YCbCr encoding
and the transfer function
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Colorimetry value will always be checked in the same way. Adding a
helper macro for that
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
All links will be checked in the same way. Adding a helper function for
that
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Move the vimc_cap_pipeline_s_stream from the vimc-cap.c to vimc-common.c
as this core will be reused by other subdevices to activate the stream
in their directly connected nodes
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As all the subdevices in the topology will be initialized in the same
way, to avoid code repetition the vimc_ent_sd_{register, unregister}
helper functions were created
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove helper functions from vimc-core and add it in vimc-common to
clean up the core.
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Initialize the test pattern generator on the sensor
Generate a colored bar image instead of a grey one
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Commit e789029761 ("i2c: sh_mobile: don't send a stop condition by
default inside transfers") makes the i2c_sh_mobile I2C-adapter emit a
stop/start sequence between messages in a single transfer only when
explicitly requested with I2C_M_STOP.
This breaks the ov772x driver in the SH4 Migo-R board as the Omnivision
sensor uses the I2C-like SCCB protocol that doesn't support repeated
starts:
i2c-sh_mobile i2c-sh_mobile.0: Transfer request timed out
ov772x 0-0021: Product ID error 92:92
Fix it by marking the client as SCCB, forcing the emission of a
stop/start sequence between all messages.
As I2C_M_STOP requires the I2C adapter to support protocol mangling,
ensure that the I2C_FUNC_PROTOCOL_MANGLING functionality is available.
Tested on SH4 Migo-R board, with OV772x now successfully probing
soc-camera-pdrv soc-camera-pdrv.0: Probing soc-camera-pdrv.0
ov772x 0-0021: ov7725 Product ID 77:21 Manufacturer ID 7f:a2
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
We want all media drivers to build with COMPILE_TEST, as the
Coverity instance we use on Kernel works only for x86. Also,
our test workflow relies on it, in order to identify git
bisect breakages.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Move power-up and power-down functionality to init/sleep ops and
get rid of old function.
Fixes and simplifies power-up functionality slightly.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
We need to wait 2nd demod power-up before download firmware. Move
that wait to more correct location.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Removed register writes are already chip defaults, are not required,
are set later or belong to AF9015 USB interface.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On serial TS mode output pin could be selected from D0 or D7.
Add configuration option to for it.
Rename TS mode config option prefix from AF9013_TS_ to AF9013_TS_MODE_.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It needs to be enabled in order to get stream from slave af9013 demod.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
* fix write+read when write has more than one byte
* remove lock, not needed on that case
* remove useless i2c msg send loop, as we support only write, read and
write+read as one go and nothing more
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use regmap for register access. Own low level i2c read and write
routines for regmap is still needed because chip uses single command
byte in addition to typical i2c register access.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
We can simplify logging as we now have a proper i2c client
to pass for kernel dev_* logging functions.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Replace own binary division with 64-bit multiply and division.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It shorten, as typed chars, access to config values as there is one
pointer less. Also, when config/platform data is passed to driver there
could be some values that are not relevant to store state as such or
not needed to store at all.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Driver was using wrong "8-bit" i2c addresses for demods and tuners.
Internal demod i2c address was not set at all. These are needed
to be fixed before proper i2c client binding is used.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check return value from call to af9013_wr_regs(), so in case of
error print debug message and return.
Addresses-Coverity-ID: 1227035
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adds hardware IDs for all Sony CXD-based Cine-cards and MaxA8 devices, also
adds some other yet missing IDs like the Octopus V3, Octopus OEM and
Octopus Mini, as well as cards with unknown/deleted sub-ids.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Properly detect and attach Ports and Flex modules with the Sony CXD28xxER
series demods. This makes newer Cine cards and most DuoFlex C/C2/T/T2 (or
any combination of these systems) work, PCI IDs need to be added though.
Note: This utilises the CXD2841ER demod driver, which requires the changes
from this patch series to properly work. Without those changes, it won't
function properly (if at all).
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some Flex modules (mostly with anyof C/C2/T/T2 demods based on the Sony
CXD28xxER series) are equipped with an interface named XO2 (which
appears to be the Lattice MachXO2). Add functionality to detect such
links and initialise them, so any tuner module with such an interface can
be used.
This also adds dummy detection for any possible connected module, telling
the user it isn't supported at this very moment.
Also adds i2c_io(), i2c_write() and i2c_write_reg(), all required for the
XO2 handling functionality.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is a backport of the board control setup from the vendor provided
dddvb driver package, which does additional device initialisation based
on the board_control device info values. Also backports the TS quirk
flags which is used to control setup and usage of the tuner modules
soldered on the bridge cards (e.g. CineCTv7, CineS2 V7, MaxA8 and the
likes).
Functionality originates from ddbridge vendor driver. Permission for
reuse and kernel inclusion was formally granted by Ralph Metzler
<rjkm@metzlerbros.de>.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On DVB-T/T2 at least, SNR might be reported as >2500dB, which not only is
just wrong but also ridiculous, so fix this by improving the conversion
of the register value.
The INTLOG10X100 function/macro and the way the values are converted were
both taken from DD's cxd2843 driver.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Bits 3 and 4 of the TSCONFIG register are important for certain hardware
constellations, in that they need to be zeroed. Add a configuration flag
to toggle this.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adds a flag to enable or disable the IFAGCNEG bit in cxd2841er_init_tc().
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't wait for FE_HAS_LOCK in set_frontend_tc() and thus don't hammer the
lock status register with inquiries when CXD2841ER_NO_WAIT_LOCK is set
in the configuration, which also unneccessarily blocks applications until
a TS LOCK has been acquired. Rather, API and applications will check for
a TS LOCK by utilising the tune fe_op, read_status and get_frontend ops,
which is sufficient.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When AUTO_IFHZ is set and the tuner is supposed to provide proper IF speed
values, it should be possible to have the tuner setup take place before
the demod is configured, else the demod might be configured with either
wrong (old), or even no values at all, which obviously will cause issues.
To set this behaviour in the most flexible way, this is done with a
separate flag instead of making this depend on AUTO_IFHZ.
It should be evaluated if tuning shouldn't take place earlier in all cases
and hardware constellations.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The Sony CXD28xx demods may have other tuner types attached to them (e.g.
NXP TDA18212), so don't mandatorily configure and enable the ASCOT
functionality, but make this conditional by a config flag.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some constellations work/need a serial TS transport mode. This adds a flag
that will toggle set up of such mode.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a AUTO_IFHZ flag and a function that will read IF speed values from any
attached tuner if the tuner supports this and if AUTO_IFHZ is enabled, and
else the passed default value (which probably matches Sony ASCOT tuners)
will be passed back. The returned value is then used to calculate the iffeq
which the demod will be programmed with.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some cards/bridges wrap i2c_gate_ctrl handling with a mutex_lock(). This is
e.g. done in ddbridge to protect against concurrent tuner access with
regards to the dual tuner HW, where concurrent tuner reconfiguration can
result in tuning fails or bad reception quality. When the tuner driver
additionally tries to open the I2C gate (which e.g. the tda18212 driver
does) when the demod already did this, this will lead to a deadlock. This
makes the calls to i2c_gatectrl from the demod driver optional when the
flag is set, leaving this to the tuner driver. For readability reasons and
to not have the check duplicated multiple times, the setup is factored
into cxd2841er_tuner_set().
This commit also updates the netup card driver (which seems to be the only
consumer of the cxd2841er as of now).
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Throughout the patch series some configuration flags will be added to the
demod driver. This patch prepares this by adding the flags var to
struct cxd2841er_config, which will serve as a bitmask to toggle various
options and behaviour in the driver.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The way the MAKE_IFFREQ_CONFIG macros are written make it impossible to
pass regular integers for iffreq calculation, since this will cause "SSE
register return with SSE disabled" compile errors. This changes the
calculation into C functions which also might help when debugging. Also,
expand all passed frequencies from MHz to Hz scale.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Those demods are programmed in the same way as the CXD2841ER/54ER and can
be handled by this driver. Support added in a way matching the existing
code, supported delivery systems are set according to what each demod
supports.
Updates the type string setting used for printing the "attaching..." log
line aswell.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Do unfreeze_regs() directly when accessing the demod registers is done,
and don't have multiple unfreeze's on different conditions, which even
can get prone to errors.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Doing the I2C read operation with two calls to i2c_transfer() causes the
exclusive I2C bus lock of the underlying adapter to be released. While this
isn't an issue if only one demodulator is attached to the bus, having two
or even more causes troubles in that concurrent accesses to the different
demods will cause all kinds of issues due to wrong data being returned on
read operations (for example, the TS config register will be set wrong).
This changes the read_regs() function to do the operation in one go (by
calling i2c_transfer with the whole msg list instead of one by one) to not
loose the I2C bus lock, fixing all sorts of random runtime failures.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This moves the I2C debug dump into the preceding dev_dbg() call by
utilising the %*ph format macro and removes the call to
print_hex_debug_bytes().
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This adds detection and activation for STV0367-based tuner hardware (namely
CineCTv6 bridge cards and older DuoFlex CT addon modules). Utilises the
extended stv0367 demod driver.
TDA18212 i2c_client/regmap-api code was originally implemented by
Antti Palosaari <crope@iki.fi> in a variant to update the ddbridge code
from the vendor dddvb package (formal ack for these parts received).
Original patch at [1].
When boards with STV0367 are cold-started, there might be issues with the
I2C gate, causing the TDA18212 detection/probe to fail. For these demods,
a workaround (tuner_tda18212_ping) is implemented which probes the tuner
twice on this hardware constellation which will resolve the problem and
put all components into a working state. Other demod/port types won't be
retried.
[1] https://patchwork.linuxtv.org/patch/25146/
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adds new i2c_read_regs() function and make i2c_read_reg() wrap into this
with len=1. Required for the tuner_tda18212_ping() and XO2 handling
functions (part of the Sony CXD28xx support patch series).
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This - in conjunction with the previous changes - makes it possible to use
the STV0367 DVB-C/T demodulator driver with Digital Devices hardware having
this demodulator soldered on them (namely CineCTv6 bridges and some earlier
DuoFlex CT addon modules).
The changes do the following:
- add a third *_attach function which will make use of a third frontend_ops
struct which announces both -C and -T support (the same as with DD's own
driver stv0367dd). This is necessary to support both delivery systems
on one FE without having to do large conversions to VB2 or the need to
select either -C or -T mode via modparams and the like. Additionally,
the frontend_ops point to new "glue" functions which will then call into
the existing functionality depending on the active delivery system/demod
state (all used functionality works almost OOTB).
- Demod initialisation has been ported from stv0367dd. DD's driver always
does a full init of both OFDM and QAM cores, with some additional things.
The active delivery system is remembered and upon switch, the Demod will
be reconfigured to work in OFDM or QAM mode (that's what the ddb_setup_XX
functions are used for). Note that in QAM mode, the DD demods work with
an IC speed of 58Mhz. It's not very good to perform full reinits upon
Demod mode changes since in very rare occasions this can lead to the I2C
interface or the whole Demod to crash, requiring a powercycle, thus the
flag to perform full reinit is set to disabled.
- A little enum is added for named identifiers of the current Demod state.
Initialisation code/register writes originate from stv0367dd. Permission
to reuse was formally granted by Ralph Metzler <rjkm@metzlerbros.de>.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Digital Devices uses defaults tables in their stv0367dd demod driver
variant which differ in a few registers, at least enough that no stable
operation can be provided with the tables already present in the driver
(init succeeds and DVB reception works but at least when the driver is
reloaded using rmmod/modprobe, the demod goes into a crashed state in a
way it doesn't react on any I2C command anymore, while even more
side-effects may occur), so there's a good reason to better have another
set of defaults.
Defaults originating from the stv0367dd driver. Permission to reuse them
was formally granted by Ralph Metzler <rjkm@metzlerbros.de>.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The values used for comparing symbol rates and the resulting conditional
reg writes seem wrong (rates multiplied by ten), so fix those values.
While this doesn't seem to influence operation, it should be fixed anyway.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In some configurations (due to different PIN config, wiring or so), the
QAM FECLock might be signalled using a different register than
F367CAB_QAMFEC_LOCK (e.g. F367CAB_DESCR_SYNCSTATE on Digital Devices hw),
so make that register selectable.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently, if_khz is set and provided using the configuration var in
struct stv0367_config. However, in some constellations, the value might be
different for differing channel bandwidths or even -T and -C operation.
When e.g. used in conjunction with TDA18212 tuners, the tuner frontend
might be aware of the different freqs. This factors if_khz retrieval in a
function, which checks a new flag if an automatic retrieval attempt should
be made, and if the tuner provides it, use it whenever needed.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Every time dvb_frontend_ops.set_frontend() is called, an almost full reinit
of the demodulator will be performed. While this might cause a slight delay
when switching channels due to all involved tables being rewritten, it can
even be dangerous in certain causes in that the demod may lock up and
requires to be powercycled (this can happen on Digital Devices hardware).
So this adds a flag if it should be done, and to not change behaviour with
existing card support, it'll be enabled in all cases.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This moves the PLL SETUP code from stv0367ter_init() into a dedicated
function, and also make it possible to configure 58Mhz IC speed at
27MHz Xtal (used on STV0367-based DDB cards/modules in QAM mode).
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Move the *ter and *cab st_register tables into a separate header file and
additionally organize them via a multidimensional array, allowing to add
more tables with differing init values, and also prepare for a base init
table which should contain general setup values. Also add a state var to
store the table triplet to be used.
Also fixes three minor style problems reported by checkpatch.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Change defaults table writing so tables can be of dynamic length without
having to keep track of their lengths by adding and evaluating an end
marker (reg 0x0000), also move table writing to a dedicated function to
remove code duplication. Additionally mark st_register tables const since
they're used read-only.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The CPAMP log lines generated in stv0367_ter_check_cpamp() are printed
everytime tuning succeeds or fails, quite cluttering the normal kernel log.
Use dprintk() instead of printk(KERN_ERR...) so that if the information is
needed, it'll be printed when the stv_debug modparam is enabled.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some hardware and bridges (namely ddbridge) require that tuner access is
limited to one concurrent access and wrap i2c gate control with a
mutex_lock when attaching frontends. According to vendor information, this
is required as concurrent tuner reconfiguration can interfere each other
and at worst cause tuning fails or bad reception quality.
If the demod driver does gate_ctrl before setting up tuner parameters, and
the tuner does another I2C enable, it will deadlock forever when gate_ctrl
is wrapped into the mutex_lock. This adds a flag and a conditional before
triggering gate_ctrl in the demodulator driver.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are multiple places where arrays or otherwise variable sized
buffer are allocated through V4L2 core code, including things like
controls, memory pages, staging buffers for ioctls and so on. Such
allocations can potentially require an order > 0 allocation from the
page allocator, which is not guaranteed to be fulfilled and is likely to
fail on a system with severe memory fragmentation (e.g. a system with
very long uptime).
Since the memory being allocated is intended to be used by the CPU
exclusively, we can consider using vmalloc() as a fallback and this is
exactly what the recently merged kvmalloc() helpers do. A kmalloc() call
is still attempted, even for order > 0 allocations, but it is done
with __GFP_NORETRY and __GFP_NOWARN, with expectation of failing if
requested memory is not available instantly. Only then the vmalloc()
fallback is used. This should give us fast and more reliable allocations
even on systems with higher memory pressure and/or more fragmentation,
while still retaining the same performance level on systems not
suffering from such conditions.
While at it, replace explicit array size calculations on changed
allocations with kvmalloc_array().
Purposedly not touching videobuf1, as it is deprecated, has only few
users remaining and would rather be seen removed instead.
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is a wrapper around the media entity get_fwnode_pad operation.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a check for v4l2_dev to v4l2_async_notifier_register() as to fail as
early as possible since this will fail later in v4l2_async_test_notify().
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The new Renesas R-Car H3 ES2.0 platforms have a new hw version register.
Update the driver accordingly, defaulting to the new hw revision, and
differentiating the older revision as ES1
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove useless variable assignment in function tc358743_isr().
The value stored in variable _intstatus_ at line 1299 is
overwritten at line 1302, just before it can be used.
Addresses-Coverity-ID: 1397678
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The davinci VPIF is a single hardware block, but the existing driver
is broken up into a common library (vpif.c), output (vpif_display.c) and
intput (vpif_capture.c).
When migrating to DT, to better model the hardware, and because
registers, interrupts, etc. are all common,it was decided to
have a single VPIF hardware node[1].
Because davinci uses legacy, non-DT boot on several SoCs still, the
platform_drivers need to remain. But they are also needed in DT boot.
Since there are no DT nodes for the display/capture parts in DT
boot (there is a single node for the parent/common device) we need to
create platform_devices somewhere to instantiate the platform_drivers.
When VPIF display/capture are needed for a DT boot, the VPIF node
will have endpoints defined for its subdevs. Therefore, vpif_probe()
checks for the presence of endpoints, and if detected manually creates
the platform_devices for the display and capture platform_drivers.
[1] Documentation/devicetree/bindings/media/ti,da850-vpif.txt
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
'call_ptr_memop' can return NULL, so we must test its return value with
'IS_ERR_OR_NULL'. Otherwise, the test 'if (mem_priv)' is meaningless.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As long as only one CODA context is running we get alternating device_run()
and wait_for_completion() calls, but when more then one CODA context is
active, other VDOA slots can be inserted between those calls for one context.
Make sure to wait on job completion before running a different context and
before destroying the currently active context.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This implements a simple handler for the case where decode did not finish
sucessfully. This might be helpful during normal streaming, but for now it
only handles the case where the context would deadlock with userspace,
i.e. userspace issued DEC_CMD_STOP and waits for EOS, but after the failed
decode run we would hold the context and wait for userspace to queue more
buffers.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The mvcol buffer needs to be placed behind the chroma plane(s), so
use the real offset including any required rounding.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This makes firmware name and path part of venus_resources
structure and initialize it properly depending on the SoC and
firmware version.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This adds support for V4L2_CID_MIN_BUFFERS_FOR_CAPTURE get control
in venus decoder, it is usable in case when the userspace wants
to know minimum capture buffers before calling request_buf for
capture queue in mem2mem drivers. Also this will fix an issue
found gstreamer v4l2videodec element, i.e. the video decoder
element cannot continue because the buffers are insufficient.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This fixes the following compile error ocured when building
with gcc7:
drivers/media/platform/qcom/venus/venc.c:1150
venc_close() error: dereferencing freed memory 'inst'
by moving kfree as a last call.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This fixes the following compile error ocured when building
with gcc7:
drivers/media/platform/qcom/venus/vdec.c:1022
vdec_close() error: dereferencing freed memory 'inst'
by moving kfree as a last call.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This fixes a warning found when building with gcc7:
drivers/media/platform/qcom/venus/hfi_msgs.c:465:40:
warning: variable 'domain' set but not used [-Wunused-but-set-variable]
u32 rem_bytes, num_props, codecs = 0, domain = 0;
^~~~~~
drivers/media/platform/qcom/venus/hfi_msgs.c:465:28:
warning: variable 'codecs' set but not used [-Wunused-but-set-variable]
u32 rem_bytes, num_props, codecs = 0, domain = 0;
The warning is avoided by deleting the variables declaration.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This fixes a warning found when building with gcc7:
drivers/media/platform/qcom/venus/hfi_venus.c:998
venus_isr_thread() warn: variable dereferenced before check
'hdev' (see line 994)
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This fixes a warning found when building the driver with gcc7:
drivers/media/platform/qcom/venus/helpers.c:157
load_per_instance() warn: variable dereferenced before check
'inst' (see line 153)
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This fixes a warning found when building the driver with gcc7:
drivers/media/platform/qcom/venus/hfi_cmds.c:415
pkt_session_set_property_1x() warn: variable dereferenced before
check 'pkt' (see line 412)
drivers/media/platform/qcom/venus/hfi_cmds.c:1177
pkt_session_set_property_3xx() warn: variable dereferenced before
check 'pkt' (see line 1174)
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This fixed a warning when build driver with gcc7:
drivers/media/platform/qcom/venus/hfi.c:171
hfi_core_ping() warn: inconsistent returns 'mutex:&core->lock'.
Locked on: line 159
Unlocked on: line 171
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This adds Venus driver Makefile and changes v4l2 platform
Makefile/Kconfig in order to enable building of the driver.
Note that in this initial version the COMPILE_TEST-ing is not
supported because the drivers specific to ARM builds are still
in process of enabling the aforementioned compile testing.
Once that disadvantage is fixed the Venus driver compile testing
will be possible with follow-up changes.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Here is the implementation of Venus video accelerator low-level
functionality. It contanins code which setup the registers and
startup uthe processor, allocate and manipulates with the shared
memory used for sending commands and receiving messages.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is the implementation of HFI. It is charged with the
responsibility to comunicate with the firmware through an
interface commands and messages.
- hfi.c has interface functions used by the core, decoder
and encoder parts to comunicate with the firmware. For example
there are functions for session and core initialisation.
- hfi_cmds has packetization operations which preparing
packets to be send from host to firmware.
- hfi_msgs takes care of messages sent from firmware to the
host.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This adds encoder part of the driver plus encoder controls.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This consists of video decoder implementation plus decoder
controls.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
* core.c has implemented the platform driver methods, file
operations and v4l2 registration.
* helpers.c has implemented common helper functions for:
- buffer management
- vb2_ops and functions for format propagation,
- functions for allocating and freeing buffers for
internal usage. The buffer parameters describing internal
buffers depends on current format, resolution and codec.
- functions for calculation of current load of the
hardware. Depending on the count of instances and
resolutions it selects the best clock rate for the video
core.
* firmware loader
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
this add functions for:
- remove buffers from src/dst queue by index
- remove exact buffer from src/dst queue
also extends m2m API to iterate over a list of src/dst buffers
in safely and non-safely manner.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
-----BEGIN PGP SIGNATURE-----
iQEbBAABAgAGBQJZR92EAAoJEHm+PkMAQRiGT1oH+KW2FLrRaYxtut+KyGA6l7tc
R/hFx1n9BibkjXeqD+y6/4SjRTe6/pT8Zkihv3/19eZ5algUWeQa0Hm+/455sl58
IdIXx/pzuCO3kqR3//fP9ZFD657GNDsuQ0fYnZESItFwiWQtO1TNfZD6KQjkqBdI
L3MVhDUVBZA2ZtPwC4ERei5/sToV9woykKoJ/A3+OkWjgX6w4SBimqgkSEFk4uE8
xS0pycyDZci93rJlECi1UueewdODTKSmhwdC80qvGEiYXzsC6UFtaF0Fj66XO1AL
UMjxqI/gkm5ZuCIjRsmPmJjgL5q1RT6UX/qtw9yn71XTmcgMiPW2/DF/v/OaTg==
=XbW2
-----END PGP SIGNATURE-----
Merge tag 'v4.12-rc6' into patchwork
Linux 4.12-rc6
* tag 'v4.12-rc6': (813 commits)
Linux 4.12-rc6
mm: larger stack guard gap, between vmas
virtio_balloon: disable VIOMMU support
mm: correct the comment when reclaimed pages exceed the scanned pages
userfaultfd: shmem: handle coredumping in handle_userfault()
mm: numa: avoid waiting on freed migrated pages
swap: cond_resched in swap_cgroup_prepare()
mm/memory-failure.c: use compound_head() flags for huge pages
perf unwind: Report module before querying isactivation in dwfl unwind
fs: pass on flags in compat_writev
objtool: Add fortify_panic as __noreturn function
powerpc/debug: Add missing warn flag to WARN_ON's non-builtin path
USB: gadgetfs, dummy-hcd, net2280: fix locking for callbacks
drm: mxsfb_crtc: Reset the eLCDIF controller
drm/mgag200: Fix to always set HiPri for G200e4 V2
i2c: ismt: fix wrong device address when unmap the data buffer
i2c: rcar: use correct length when unmapping DMA
powerpc/xive: Fix offset for store EOI MMIOs
drm/tegra: Correct idr_alloc() minimum id
drm/tegra: Fix lockup on a use of staging API
...
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There is no need to split long string literals.
Join them back.
No functional change intended.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
DW9714 is a 10 bit DAC, designed for linear
control of voice coil motor.
This driver creates a V4L2 subdevice and
provides control to set the desired focus.
[Sakari Ailus: Add MAINTAINERS entry.]
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds driver for Omnivision's ov13858
sensor, the driver supports following features:
- manual exposure/gain(analog and digital) control support
- two link frequencies
- VBLANK/HBLANK support
- test pattern support
- media controller support
- runtime pm support
- supported resolutions
+ 4224x3136 at 30FPS
+ 2112x1568 at 30FPS(default) and 60FPS
+ 2112x1188 at 30FPS(default) and 60FPS
+ 1056x784 at 30FPS(default) and 60FPS
[Sakari Ailus: use V4L2_CID_DIGITAL_GAIN instead, add MAINTAINERS entry.]
Signed-off-by: Hyungwoo Yang <hyungwoo.yang@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add V4L2_CID_DIGITAL_GAIN to control explicitly digital gain.
We already have analogue gain control which the digital gain control
complements. Typically higher quality images are obtained using analogue
gain only as the digital gain does not add information to the image
(rather it may remove it).
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This driver is based on ov5640_mipi.c from Freescale imx_3.10.17_1.0.0_beta
branch, modified heavily to bring forward to latest interfaces and code
cleanup.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This driver can handle SoC internal and external video bus multiplexers,
controlled by mux controllers provided by the mux controller framework,
such as MMIO register bitfields or GPIOs. The subdevice passes through
the mbus configuration of the active input to the output side.
Since the mux framework is not yet merged, this driver contains
temporary mmio-mux support to work without the framework. The driver
should be converted to use the multiplexer API once the "mux: minimal
mux subsystem" and "mux: mmio-based syscon mux controller" patches are
merged.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
[hans.verkuil@cisco.com: add 'select REGMAP' to Kconfig]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
load is an unsigned integer. So, it is always bigger or equal
to zero, as reported by gcc:
drivers/media/i2c/max2175.c: In function 'max2175_refout_load_to_bits':
drivers/media/i2c/max2175.c:1272:11: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
if (load >= 0 && load <= 40)
^~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds Digital Radio Interface (DRIF) support to R-Car Gen3 SoCs.
The driver exposes each instance of DRIF as a V4L2 SDR device. A DRIF
device represents a channel and each channel can have one or two
sub-channels respectively depending on the target board.
DRIF supports only Rx functionality. It receives samples from a RF
frontend tuner chip it is interfaced with. The combination of DRIF and the
tuner device, which is registered as a sub-device, determines the receive
sample rate and format.
In order to be compliant as a V4L2 SDR device, DRIF needs to bind with
the tuner device, which can be provided by a third party vendor. DRIF acts
as a slave device and the tuner device acts as a master transmitting the
samples. The driver allows asynchronous binding of a tuner device that
is registered as a v4l2 sub-device. The driver can learn about the tuner
it is interfaced with based on port endpoint properties of the device in
device tree. The V4L2 SDR device inherits the controls exposed by the
tuner device.
The device can also be configured to use either one or both of the data
pins at runtime based on the master (tuner) configuration.
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds support for the three new SDR formats. These formats
were prefixed with "planar" indicating I & Q data are not interleaved
as in other formats. Here, I & Q data constitutes the top half and bottom
half of the received buffer respectively.
V4L2_SDR_FMT_PCU16BE - 14-bit complex (I & Q) unsigned big-endian sample
inside 16-bit. V4L2 FourCC: PC16
V4L2_SDR_FMT_PCU18BE - 16-bit complex (I & Q) unsigned big-endian sample
inside 18-bit. V4L2 FourCC: PC18
V4L2_SDR_FMT_PCU20BE - 18-bit complex (I & Q) unsigned big-endian sample
inside 20-bit. V4L2 FourCC: PC20
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds driver support for the MAX2175 chip. This is Maxim
Integrated's RF to Bits tuner front end chip designed for software-defined
radio solutions. This driver exposes the tuner as a sub-device instance
with standard and custom controls to configure the device.
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use the needs-hpd DT property to determine if the CEC_CAP_NEEDS_HPD
should be set.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a new capability CEC_CAP_NEEDS_HPD. If this capability is set
then the hardware can only use CEC if the HDMI Hotplug Detect pin
is high. Such hardware cannot handle the corner case in the CEC specification
where it is possible to transmit messages even if no hotplug signal is
present (needed for some displays that turn off the HPD when in standby,
but still have CEC enabled).
Typically hardware that needs this capability have the HPD wired to the CEC
block, often to a 'power' or 'active' pin.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use the helper function cec_transmit_attempt_done instead of
cec_transmit_done to simplify the code.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A simpler variant of cec_transmit_done to be used where the HW does
just a single attempt at a transmit. So if the status indicates an
error, then the corresponding error count will always be 1 and this
function figures that out based on the status argument.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This function simplifies the integration of CEC in DRM drivers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions (skb_put, __skb_put and pskb_put) return void *
and remove all the casts across the tree, adding a (u8 *) cast only
where the unsigned char pointer was used directly, all done with the
following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_put, __skb_put };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_put, __skb_put };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
which actually doesn't cover pskb_put since there are only three
users overall.
A handful of stragglers were converted manually, notably a macro in
drivers/isdn/i4l/isdn_bsdcomp.c and, oddly enough, one of the many
instances in net/bluetooth/hci_sock.c. In the former file, I also
had to fix one whitespace problem spatch introduced.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZPdbLAAoJEHm+PkMAQRiGx4wH/1nCjfnl6fE8oJ24/1gEAOUh
biFdqJkYZmlLYHVtYfLm4Ueg4adJdg0wx6qM/4RaAzmQVvLfDV34bc1qBf1+P95G
kVF+osWyXrZo5cTwkwapHW/KNu4VJwAx2D1wrlxKDVG5AOrULH1pYOYGOpApEkZU
4N+q5+M0ce0GJpqtUZX+UnI33ygjdDbBxXoFKsr24B7eA0ouGbAJ7dC88WcaETL+
2/7tT01SvDMo0jBSV0WIqlgXwZ5gp3yPGnklC3F4159Yze6VFrzHMKS/UpPF8o8E
W9EbuzwxsKyXUifX2GY348L1f+47glen/1sedbuKnFhP6E9aqUQQJXvEO7ueQl4=
=m2Gx
-----END PGP SIGNATURE-----
BackMerge tag 'v4.12-rc5' into drm-next
Linux 4.12-rc5 for nouveau fixes
-----BEGIN PGP SIGNATURE-----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=GEtG
-----END PGP SIGNATURE-----
Merge tag 'media/v4.12-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- some build dependency issues at CEC core with randconfigs
- fix an off by one error at vb2
- a race fix at cec core
- driver fixes at tc358743, sir_ir and rainshadow-cec
* tag 'media/v4.12-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] media/cec.h: use IS_REACHABLE instead of IS_ENABLED
[media] cec: race fix: don't return -ENONET in cec_receive()
[media] sir_ir: infinite loop in interrupt handler
[media] cec-notifier.h: handle unreachable CONFIG_CEC_CORE
[media] cec: improve MEDIA_CEC_RC dependencies
[media] vb2: Fix an off by one error in 'vb2_plane_vaddr'
[media] rainshadow-cec: Fix missing spin_lock_init()
[media] tc358743: fix register i2c_rd/wr function fix
Fix the position of arguments so camif->colorfx_cb, camif->colorfx_cr
are passed in proper order to the camif_hw_set_effect() function.
Addresses-Coverity-ID: 1248800
Addresses-Coverity-ID: 1269141
[s.nawrocki@samsung.com: edited commit message ]
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As this is not in atomic context and it does not seem like a critical
timing setting a range of 1ms allows the timer subsystem to optimize
the hrtimer here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use colorspace provided by the user as we are only doing scaling and
color encoding conversion, we won't be able to transform the colorspace
itself and the colorspace won't mater in that operation.
Also always use output colorspace on the capture side.
If the user does not provide a colorspace do not make it up, we might
later while processing need to figure out the colorspace, which
is possible depending on the frame size but do not ever guess and
leak that guess to the userspace.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Thibault Saunier <thibault.saunier@osg.samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Trivial fix to spelling mistake in mfc_err error messages
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2_m2m_job_finish(), which is called from the interrupt handler with
slock acquired, can call the device_run() hook immediately if another
context was in the queue. This hook also acquires slock, resulting in
a deadlock for this scenario.
Fix this by releasing slock right before calling v4l2_m2m_job_finish().
This is safe to do as the state of the hardware cannot change before
v4l2_m2m_job_finish() is called anyway.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Now that rc_register_device() is reorganised, the dev->initialized
hack can be removed. Any driver which calls rc_register_device()
must be prepared for the device to go live immediately.
The dev->initialized commits that are relevant are commit c73bbaa4ec
("[media] rc-core: don't lock device at rc_register_device()") and
commit 08aeb7c9a4 ("[media] rc: add locking to fix register/show race").
The original problem was that show_protocols() would access
dev->rc_map.* and various other bits which are now properly
initialized before device_add() is called.
At the same time, remove the bogus "device is being removed" check.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The device core infrastructure is based on the presumption that
once a driver calls device_add(), it must be ready to accept
userspace interaction.
This requires splitting rc_setup_rx_device() into two functions
and reorganizing rc_register_device() so that as much work
as possible is performed before calling device_add().
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This module was merged after commit 5a8fc6a3ce ("Annotate hardware
config module parameters in drivers/media/"), so add add the missing
hardware annotations.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hugues Fruchet