Fix the incorrect "select" directives by dropping the "CONFIG_"
prefixes, and correcting the typo "H8S2768" to "H8S2678".
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Acked-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Fix up HAVE_PERF_COUNTERS typo.
sh: Fix up more dma-mapping fallout.
sh: SH7786 SMP support.
sh: Wire up the uncached fixmap on sh64 as well.
sh: Use local TLB flush in set_pte_phys().
sh: Provide cpu_idle_wait() to fix up cpuidle/SMP build.
That's HAVE_PERF_COUNTERS not HAVE_PERF_COUNTER. This was right
initially but I seem to have screwed it up while re-typing it out
by hand on another machine when I checked it in. Hmph.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
commit dbe6f18691
("dma-mapping: mark dma_sync_single and dma_sync_sg as deprecated"
conveniently broke every single SH build.
In the future it would be great if people could at least bother
figuring out how to use grep.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH7786 is roughly identical to SH-X3 proto SMP, though there are only 2
CPUs. This just wraps in to the existing SH-X3 SMP code with some minor
changes for SH7786, including wiring up the IPIs properly, enabling
IRQ_PER_CPU, and so forth.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
set_pte_phys() presently uses the global flush_tlb_one(), which locks on
SMP trying to do the IPI. As we have not even initialized the other CPUs
at this point, switch to the local_ variant so the flush happens on the
boot CPU.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Crib the x86 cpu_idle_wait() implementation and shove it in with the
idle code, subsequently enabling ARCH_HAS_CPU_IDLE_WAIT.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Since dmanr is unsigned, negatives are wrapped and caught by the other test.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin: (27 commits)
Blackfin: fix dma-mapping build errors
Blackfin: hook up new perf_counter_open syscall
Blackfin: drop BF535-specific text for exception 0x2A (unaligned instruction)
Blackfin: fix early crash when booting on wrong cpu
Blackfin: fix GPTMR0_CLOCKSOURCE dependency on BFIN_GPTIMERS
Blackfin: drop unused ISP1760 port1_disable from board resources
Blackfin: bf526-ezbrd: handle different SDRAM chips
Blackfin: fix typo in TRAS define in mem_init.h header
Blackfin: unify memory map headers
Blackfin: stick the CPU name into boot image name
Blackfin: update defconfigs
Blackfin: decouple unrelated cache settings to get exact behavior
Blackfin: update I-pipe patch level
Blackfin: remove obsolete mcount support from I-pipe code
Blackfin: allow CONFIG_TICKSOURCE_GPTMR0 with interrupt pipeline
Blackfin: convert interrupt pipeline to irqflags
Blackfin: allow people to select BF51x-0.1 silicon rev
Blackfin: bf526-ezbrd: set SPI flash resources to SST device
Blackfin: fix accidental reset in some boot modes
Blackfin: abstract irq14 lowering in do_irq
...
* git://git.infradead.org/~dwmw2/iommu-2.6.31:
intel-iommu: Fix one last ia64 build problem in Pass Through Support
VT-d: support the device IOTLB
VT-d: cleanup iommu_flush_iotlb_psi and flush_unmaps
VT-d: add device IOTLB invalidation support
VT-d: parse ATSR in DMA Remapping Reporting Structure
PCI: handle Virtual Function ATS enabling
PCI: support the ATS capability
intel-iommu: dmar_set_interrupt return error value
intel-iommu: Tidy up iommu->gcmd handling
intel-iommu: Fix tiny theoretical race in write-buffer flush.
intel-iommu: Clean up handling of "caching mode" vs. IOTLB flushing.
intel-iommu: Clean up handling of "caching mode" vs. context flushing.
VT-d: fix invalid domain id for KVM context flush
Fix !CONFIG_DMAR build failure introduced by Intel IOMMU Pass Through Support
Intel IOMMU Pass Through Support
Fix up trivial conflicts in drivers/pci/{intel-iommu.c,intr_remapping.c}
The recent deprecation of dma_sync_{sg,single} ironically broke Blackfin
systems. This is because we don't define dma_sync_sg_for_cpu at all, so
until the DMA asm-generic conversion/cleanup is done after the next
release, simply stub out the dma_sync_sg_for_{cpu,device} functions.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We don't support the BF535 at all, and the exception 0x2A text specific to
it is pretty verbose and confusing (since the behavior is simply odd), so
punt it to keep the noise down.
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Make sure we process the kernel command line before poking the hardware,
so that we can process early printk. This helps ensure that if you boot
a kernel configured for a different processor, something will be left in
the log buffer.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The GPTMR0_CLOCKSOURCE Kconfig option requires the gptimers framework, so
make sure it is selected when this option is enabled.
Reported-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The BF526-EZBRD changed SDRAM chips between board revisions, so create a
timing table that can accommodate both.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We defined SDRAM_tRAS to TRAS_4, but then wrongly defined SDRAM_tRAS_num
to 3.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Many aspects of the Blackfin memory map is exactly the same across all
variants. Rather than copy and paste all of these duplicated values in
each header, unify all of these into the common Blackfin memory map header
file. In the process, push down BF561 SMP specific stuff to the BF561
specific header to keep the noise down.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Rather than use "Linux" in the boot image name (as this is redundant --
the image type is already set to "linux"), use the CPU name. This makes
it fairly obvious when a wrong image is accidentally booted. Otherwise
there is no kernel output and you waste time scratching your head
wondering wtf just happened.
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current cache options don't really represent the hardware features.
They end up setting different aspects of the hardware so that the end
result is to turn on/off the cache. Unfortunately, when we hit cache
problems with the hardware, it's difficult to test different settings to
root cause the problem. The current settings also don't cleanly allow for
different caching behaviors with different regions of memory.
So split the configure options such that they properly reflect the settings
that are applied to the hardware.
Signed-off-by: Jie Zhang <jie.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The BF526-EZBRD has a SST SPI flash on it, not a ST Micro.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We read the SWRST (Software Reset) register to get at the last reset
state, and then we may configure the DOUBLE_FAULT bit to control behavior
when a double fault occurs. But if the lower bits of the register is
already set (like UART boot mode on a BF54x), we inadvertently make the
system reset by writing to the SYSTEM_RESET field at the same time. So
make sure the lower 4 bits are always cleared.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Split out the optional IRQ14 lowering code to further simplify the
asm_do_IRQ() function and keep the ifdef nest under control.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Take a page from x86 and abstract the stack checking out of the
asm_do_IRQ() function so that the result is easier to digest.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
With the common IRQ code initializing much more of the irq_desc state, we
can't blindly initialize it ourselves to the local bad_irq state. If we
do, we end up wrongly clobbering many fields. So punt most of the bad irq
code as the common layers will handle the default state, and simply call
handle_bad_irq() directly when the IRQ we are processing is invalid.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The BF533-EZKIT has two Flash In-System Programming devices hooked up to
the async memory bus, so add resources for the primary flashes and the
SRAMs on the devices.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The kgdb (in multiple places) and traps code developed pretty much
identical checks for how to access different regions of the Blackfin
memory map, but each wasn't 100%, so unify them to avoid duplication,
bitrot, and bugs with edge cases.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* git://git.infradead.org/mtd-2.6: (63 commits)
mtd: OneNAND: Allow setting of boundary information when built as module
jffs2: leaking jffs2_summary in function jffs2_scan_medium
mtd: nand: Fix memory leak on txx9ndfmc probe failure.
mtd: orion_nand: use burst reads with double word accesses
mtd/nand: s3c6400 support for s3c2410 driver
[MTD] [NAND] S3C2410: Use DIV_ROUND_UP
[MTD] [NAND] S3C2410: Deal with unaligned lengths in S3C2440 buffer read/write
[MTD] [NAND] S3C2410: Allow the machine code to get the BBT table from NAND
[MTD] [NAND] S3C2410: Added a kerneldoc for s3c2410_nand_set
mtd: physmap_of: Add multiple regions and concatenation support
mtd: nand: max_retries off by one in mxc_nand
mtd: nand: s3c2410_nand_setrate(): use correct macros for 2412/2440
mtd: onenand: add bbt_wait & unlock_all as replaceable for some platform
mtd: Flex-OneNAND support
mtd: nand: add OMAP2/OMAP3 NAND driver
mtd: maps: Blackfin async: fix memory leaks in probe/remove funcs
mtd: uclinux: mark local stuff static
mtd: uclinux: do not allow to be built as a module
mtd: uclinux: allow systems to override map addr/size
mtd: blackfin NFC: fix hang when using NAND on BF527-EZKITs
...
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (49 commits)
[ARM] idle: clean up pm_idle calling, obey hlt_counter
[ARM] S3C: Fix gpio-config off-by-one bug
[ARM] S3C64XX: add to_irq() support for EINT() GPIO
[ARM] S3C64XX: clock.c: fix typo in usb-host clock ctrlbit
[ARM] S3C64XX: fix HCLK gate defines
[ARM] Update mach-types
[ARM] wire up rt_tgsigqueueinfo and perf_counter_open
OMAP2 clock/powerdomain: off by 1 error in loop timeout comparisons
OMAP3 SDRC: set FIXEDDELAY when disabling SDRC DLL
OMAP3: Add support for DPLL3 divisor values higher than 2
OMAP3 SRAM: convert SRAM code to use macros rather than magic numbers
OMAP3 SRAM: add more comments on the SRAM code
OMAP3 clock/SDRC: program SDRC_MR register during SDRC clock change
OMAP3 clock: add a short delay when lowering CORE clk rate
OMAP3 clock: initialize SDRC timings at kernel start
OMAP3 clock: remove wait for DPLL3 M2 clock to stabilize
[ARM] Add old Feroceon support to compressed/head.S
[ARM] 5559/1: Limit the stack unwinding caused by a kthread exit
[ARM] 5558/1: Add extra checks to ARM unwinder to avoid tracing corrupt stacks
[ARM] 5557/1: Discard some ARM.ex*.*exit.text sections when !HOTPLUG or !HOTPLUG_CPU
...
pm_idle is used by infrastructure (eg, cpuidle) which expects architectures
to call it in a certain way. Arrange for ARM to follow x86's lead on this
and call pm_idle() with interrupts already disabled. However, we expect
pm_idle() to enable interrupts before it returns.
Also, OMAP wants to be able to disable hlt-ing, so allow hlt_counter to
prevent all calls to pm_idle.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the MN10300 vmlinux ldscript. It needs to use various macros from
asm-generic/vmlinux.lds.h to correctly include all that it needs to.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (74 commits)
PCI: make msi_free_irqs() to use msix_mask_irq() instead of open coded write
PCI: Fix the NIU MSI-X problem in a better way
PCI ASPM: remove get_root_port_link
PCI ASPM: cleanup pcie_aspm_sanity_check
PCI ASPM: remove has_switch field
PCI ASPM: cleanup calc_Lx_latency
PCI ASPM: cleanup pcie_aspm_get_cap_device
PCI ASPM: cleanup clkpm checks
PCI ASPM: cleanup __pcie_aspm_check_state_one
PCI ASPM: cleanup initialization
PCI ASPM: cleanup change input argument of aspm functions
PCI ASPM: cleanup misc in struct pcie_link_state
PCI ASPM: cleanup clkpm state in struct pcie_link_state
PCI ASPM: cleanup latency field in struct pcie_link_state
PCI ASPM: cleanup aspm state field in struct pcie_link_state
PCI ASPM: fix typo in struct pcie_link_state
PCI: drivers/pci/slot.c should depend on CONFIG_SYSFS
PCI: remove redundant __msi_set_enable()
PCI PM: consistently use type bool for wake enable variable
x86/ACPI: Correct maximum allowed _CRS returned resources and warn if exceeded
...
Fix gpio-config off-by-one bug. Without this patch, touching GPA0 pin on
S3C64XX platform causes kernel oops.
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
N group
Add to_irq() function to onvert gpio to irq for external interrupt
group (GPN).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The usb-host clock was using the wrong define (the SCLK enable for the
usb-host-bus) to change the HCLK register instead of the HCLK_UHOST bit.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Robert P. J. Day