In a link bounce scenario, a condition can occur where the discovery
engine swaps an ndlp structure (address change for an nport). While the
swap was successfully executed by the discovery engine, the driver did
not properly detect a change in the ndlp bound to the nvme rport. This
error resulted in the nvme host transport issuing an IO to the correct
nvme rport, but the lpfc driver addressed a ndlp with an NLP_UNUSED
status and failed the io. This resulting it it looking like there were
missing namespaces and applications failed due to io errors.
To fix, in lpfc_nvme_register_rport, rework the "rebind" case to break
the nvme rport<->ndlp association when the ndlp already has an
nrport. Then rebind the rport to the correct ndlp data and backpointers.
[mkp: typo]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver crashes when attempting to use a freed ndpl pointer.
The pci_remove_one handler runs on a separate kernel thread. The order
of the removal is starting by freeing all of the ndlps and then
disabling interrupts. In between these two events the driver can still
receive an ELS and process it. When it tries to use the ndlp pointer
will be NULL
Change the order of the pci_remove_one vs disable interrupts so that
interrupts are disabled before the ndlp's are freed.
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During pci hot plug, the kernel crashes in a list_add_call
The lookup by tag function will return null if the IOCB is out of range
or does not have the on txcmplq flag set.
Fix: Check for null return from lookup by tag.
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During pci hot plug, the kernel crashes in timer management code.
The sli4 remove_one handler is not stoping the timers as it starts to
remove the port so that it can be swapped.
Fix: Stop the timers early in the handler routine.
Note: Fix in SLI-4 only. SLI-3 already stopped the timers properly.
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Gerry Morong <gerry.morong@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix a small cosmetic bug in a very rarely encountered error message that
can occur when a LD has a corrupted raid map.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the driver's PCI IDs.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
iscsi_session_teardown was the only user of this function. Function
currently is just short for iscsi_remove_session + iscsi_free_session.
Signed-off-by: Khazhismel Kumykov <khazhy@google.com>
Acked-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Session attributes exposed through sysfs were freed before the device
was destroyed, resulting in a potential use-after-free. Free these
attributes after removing the device.
Signed-off-by: Khazhismel Kumykov <khazhy@google.com>
Acked-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A user may lower the max_sectors_kb setting in sysfs to accommodate
certain workloads. Previously we would always set the max I/O size to
either the block layer default or the optional preferred I/O size
reported by the device.
Keep the current heuristics for the initial setting of max_sectors_kb.
For subsequent invocations, only update the current queue limit if it
exceeds the capabilities of the hardware.
Cc: <stable@vger.kernel.org>
Reported-by: Don Brace <don.brace@microsemi.com>
Reviewed-by: Martin Wilck <mwilck@suse.com>
Tested-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SBC-4 states:
"A MAXIMUM UNMAP LBA COUNT field set to a non-zero value indicates the
maximum number of LBAs that may be unmapped by an UNMAP command"
"A MAXIMUM WRITE SAME LENGTH field set to a non-zero value indicates
the maximum number of contiguous logical blocks that the device server
allows to be unmapped or written in a single WRITE SAME command."
Despite the spec being clear on the topic, some devices incorrectly
expect WRITE SAME commands with the UNMAP bit set to be limited to the
value reported in MAXIMUM UNMAP LBA COUNT in the Block Limits VPD.
Implement a blacklist option that can be used to accommodate devices
with this behavior.
Cc: <stable@vger.kernel.org>
Reported-by: Bill Kuzeja <William.Kuzeja@stratus.com>
Reported-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Eight mostly minor fixes for recently discovered issues in drivers.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=v2G5
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Eight mostly minor fixes for recently discovered issues in drivers"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ILLEGAL REQUEST + ASC==27 => target failure
scsi: aacraid: Add a small delay after IOP reset
scsi: scsi_transport_fc: Also check for NOTPRESENT in fc_remote_port_add()
scsi: scsi_transport_fc: set scsi_target_id upon rescan
scsi: scsi_transport_iscsi: fix the issue that iscsi_if_rx doesn't parse nlmsg properly
scsi: aacraid: error: testing array offset 'bus' after use
scsi: lpfc: Don't return internal MBXERR_ERROR code from probe function
scsi: aacraid: Fix 2T+ drives on SmartIOC-2000
ASC 0x27 is "WRITE PROTECTED". This error code is returned e.g. by
Fujitsu ETERNUS systems under certain conditions for WRITE SAME 16
commands with UNMAP bit set. It should not be treated as a path
error. In general, it makes sense to assume that being write protected
is a target rather than a path property.
Signed-off-by: Martin Wilck <mwilck@suse.com>
Acked-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove unused variable sas_ha to clean up build warning
"unused variable sas_ha [-Wunused-variable]"
Fixes: 042ebd293b ("scsi: libsas: kill useless ha_event and do some cleanup")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since the command type of UTRD in UFS 2.1 specification is the same with
UFS 2.0. And it assumes the future UFS specification will follow the
same definition.
Signed-off-by: kehuanlin <kehuanlin@pinecone.net>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Several configurable fields of the Device Descriptor and the Unit
Descriptors determine the Boot LUN status. The bBootEnable field and the
bBootLunEn attribute is set to zero by default, so the Boot LUN is
disabled by default.
At which point the scsi device add for Boot LUN will fail, but we can
continue to use the ufs device in fact. This failure shouldn't abort the
device boot.
Signed-off-by: Huanlin Ke <kehuanlin@pinecone.net>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 0e9973ed33 ("scsi: aacraid: Add periodic checks to see IOP reset
status") changed the way driver checks if a reset succeeded. Now, after an
IOP reset, aacraid immediately start polling a register to verify the reset
is complete.
This behavior cause regressions on the reset path in PowerPC (at least).
Since the delay after the IOP reset was removed by the aforementioned patch,
the fact driver just starts to read a register instantly after the reset
was issued (by writing in another register) "corrupts" the reset procedure,
which ends up failing all the time.
The issue highly impacted kdump on PowerPC, since on kdump path we
proactively issue a reset in adapter (through the reset_devices kernel
parameter).
This patch (re-)adds a delay right after IOP reset is issued. Empirically
we measured that 3 seconds is enough, but for safety reasons we delay
for 5s (and since it was 30s before, 5s is still a small amount).
For reference, without this patch we observe the following messages
on kdump kernel boot process:
[ 76.294] aacraid 0003:01:00.0: IOP reset failed
[ 76.294] aacraid 0003:01:00.0: ARC Reset attempt failed
[ 86.524] aacraid 0003:01:00.0: adapter kernel panic'd ff.
[ 86.524] aacraid 0003:01:00.0: Controller reset type is 3
[ 86.524] aacraid 0003:01:00.0: Issuing IOP reset
[146.534] aacraid 0003:01:00.0: IOP reset failed
[146.534] aacraid 0003:01:00.0: ARC Reset attempt failed
Fixes: 0e9973ed33 ("scsi: aacraid: Add periodic checks to see IOP reset status")
Cc: stable@vger.kernel.org # v4.13+
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Acked-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During failover there is a small race window between fc_remote_port_add()
and fc_timeout_deleted_rport(); the latter drops the lock after setting the
port to NOTPRESENT, so if fc_remote_port_add() is called right at that time
it will fail to detect the existing rport and happily adding a new
structure, causing rports to get registered twice.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since right after the user copy, we are going to memset(&karg, 0,
sizeof(karg)), the copy_from_user is redundant
Signed-off-by: Meng Xu <mengxu.gatech@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use *_pool_zalloc rather than *_pool_alloc followed by memset with 0.
Found by coccinelle spatch "api/alloc/pool_zalloc-simple.cocci"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use *_pool_zalloc rather than *_pool_alloc followed by memset with 0.
Found by coccinelle spatch "api/alloc/pool_zalloc-simple.cocci"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Device handlers are optional, and for some handlers like ALUA only
implemented for certain device types. So suppress any errors for
unsupported devices.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rather than having each device handler implementing their own error
mapping, have the ->attach() call return a SCSI_DH_XXX error code and
implement the mapping in scsi_dh_handler_attach().
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When an rport is found in the bindings array there is no guarantee that
it had been a target port, so we need to call fc_remote_port_rolechg()
here to ensure the scsi_target_id is set correctly. Otherwise the port
will never be scanned.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Tested-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reporting a maximum number of blocks that is not aligned on the device
physical size would cause a large write same request to be split into
physically unaligned chunks by __blkdev_issue_write_zeroes() and
__blkdev_issue_write_same(), even if the caller of these functions took
care to align its request to physical sectors.
Make sure the maximum reported is aligned to the device physical block
size. This is only an optional optimization for regular disks, but this
is mandatory to avoid failure of large write same requests directed at
sequential write required zones of host-managed ZBC disks.
[mkp: tweaked commit message]
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set PCIe relaxed ordering bits in FW_IQ_CMD if relaxed ordering is
enabled in the PCIe device.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ChunYu found a kernel crash by syzkaller:
[ 651.617875] kasan: CONFIG_KASAN_INLINE enabled
[ 651.618217] kasan: GPF could be caused by NULL-ptr deref or user memory access
[ 651.618731] general protection fault: 0000 [#1] SMP KASAN
[ 651.621543] CPU: 1 PID: 9539 Comm: scsi Not tainted 4.11.0.cov #32
[ 651.621938] Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
[ 651.622309] task: ffff880117780000 task.stack: ffff8800a3188000
[ 651.622762] RIP: 0010:skb_release_data+0x26c/0x590
[...]
[ 651.627260] Call Trace:
[ 651.629156] skb_release_all+0x4f/0x60
[ 651.629450] consume_skb+0x1a5/0x600
[ 651.630705] netlink_unicast+0x505/0x720
[ 651.632345] netlink_sendmsg+0xab2/0xe70
[ 651.633704] sock_sendmsg+0xcf/0x110
[ 651.633942] ___sys_sendmsg+0x833/0x980
[ 651.637117] __sys_sendmsg+0xf3/0x240
[ 651.638820] SyS_sendmsg+0x32/0x50
[ 651.639048] entry_SYSCALL_64_fastpath+0x1f/0xc2
It's caused by skb_shared_info at the end of sk_buff was overwritten by
ISCSI_KEVENT_IF_ERROR when parsing nlmsg info from skb in iscsi_if_rx.
During the loop if skb->len == nlh->nlmsg_len and both are sizeof(*nlh),
ev = nlmsg_data(nlh) will acutally get skb_shinfo(SKB) instead and set a
new value to skb_shinfo(SKB)->nr_frags by ev->type.
This patch is to fix it by checking nlh->nlmsg_len properly there to
avoid over accessing sk_buff.
Reported-by: ChunYu Wang <chunwang@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The qla2xxx driver uses the FC-specific error when it needed to return an
error to the FC-NVME transport. Convert to use a generic value instead.
Signed-off-by: James Smart <james.smart@broadcom.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The lpfc driver uses the FC-specific error when it needed to return an
error to the FC-NVME transport. Convert to use a generic value instead.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fix possible indexing array of bound for &aac->hba_map[bus][cid], where
bus and cid boundary check happens later.
Fixes: 0d643ff3c3 ("scsi: aacraid: use aac_tmf_callback for reset fib")
Signed-off-by: Nikola Pajkovsky <npajkovsky@suse.cz>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
csk is always null on the error return path and so the non-null check
and call to cxgbi_sock_closed on csk is redundant and can be removed.
Detected by: CoverityScan CID#114329 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Events will be added to defer_q list when setting ha->status to
SAS_HA_DRAINING. Events will be called after drain workqueue.
Those events are added to the head of list, but they are scanned one by
one from the head to the tail, which will cause those events be called
in the reverse order of being added. So change list_add to list_add_tail
in function sas_queue_work.
Signed-off-by: chenxiang <chenxiang66@hisilicon.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: John Garry <john.garry@huawei.com>
CC: Johannes Thumshirn <jthumshirn@suse.de>
CC: Ewan Milne <emilne@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Tomas Henzl <thenzl@redhat.com>
CC: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rename function notify_port_event() to sas_notify_port_event(), which
will be consistent with sas_notify_phy_event().
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: John Garry <john.garry@huawei.com>
CC: Johannes Thumshirn <jthumshirn@suse.de>
CC: Ewan Milne <emilne@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Tomas Henzl <thenzl@redhat.com>
CC: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ha_event now has only one event HAE_RESET, and this event does
nothing. Kill it and do some cleanup.
This is a preparation for enhance libsas hotplug feature in the next
patches.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
CC: Johannes Thumshirn <jthumshirn@suse.de>
CC: Ewan Milne <emilne@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Tomas Henzl <thenzl@redhat.com>
CC: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Internal error codes happen to be positive, thus the PCI driver core
won't treat them as failure, but we do. This would cause a crash later
on as lpfc_pci_remove_one() is called (e.g. as shutdown function).
Fixes: 6d368e5321 ("[SCSI] lpfc 8.3.24: Add resource extent support")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The logic for supporting large drives was previously tied to 4Kn support
for SmartIOC-2000. As SmartIOC-2000 does not support volumes using 4Kn
drives, use the intended option flag AAC_OPT_NEW_COMM_64 to determine
support for volumes greater than 2T.
Cc: <stable@vger.kernel.org>
Signed-off-by: Dave Carroll <david.carroll@microsemi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a NETDEV_UNREGISTER notification is received the network device is
_deleted_ after the callback returns. So we cannot use a workqueue
here, as this would cause an inversion when removing the device as the
netdev is already gone. This manifests with a nasty warning during
shutdown:
sysfs group ffffffff81eff0e0 not found for kobject 'fc_host7'
So open-code fcoe_destroy_work() when receiving the notification to
avoid this inversion.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Separate out fcoe_vport_remove() from fcoe_destroy_work(). Required for
the next patch.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This closes a possible race condition in _fcoe_create() where we drop
the rtnl_lock() before calling fcoe_interface_remove().
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Don't populate const arrays on the stack, instead make them static.
Makes the object code smaller by over 740 bytes.
Before:
text data bss dec hex filename
3840 208 0 4048 fd0 drivers/scsi/ufs/tc-dwc-g210.o
After:
text data bss dec hex filename
2679 624 0 3303 ce7 drivers/scsi/ufs/tc-dwc-g210.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pointers bnx2i_cmd are set but never used, so they can be removed.
Signed-off-by: Christos Gkekas <chris.gekas@gmail.com>
Acked-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The pointer eqe is always non-null inside the while loop, so the check
to see if eqe is NULL is redudant and hence can be removed.
Detected by CoverityScan CID#1248693 ("Logically Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When calling SG_GET_REQUEST_TABLE ioctl only a half-filled table is
returned; the remaining part will then contain stale kernel memory
information. This patch zeroes out the entire table to avoid this
issue.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Factor out sg_fill_request_table() for better readability.
[mkp: typos, applied by hand]
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After series of changes around WRITE_SAME and UNMAP setup we ended up
with leftover unnecessary condition. Remove it.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A cleanup patch introduced a fatal typo from inbalanced curly braces:
drivers/scsi/arm/acornscsi.c: In function 'acornscsi_host_reset':
drivers/scsi/arm/acornscsi.c:2773:1: error: ISO C90 forbids mixed declarations and code [-Werror=declaration-after-statement]
drivers/scsi/arm/acornscsi.c:2795:12: error: invalid storage class for function 'acornscsi_show_info'
static int acornscsi_show_info(struct seq_file *m, struct Scsi_Host *instance)
The same patch incorrectly changed the argument type of the reset
handler, as shown by this warning:
drivers/scsi/arm/acornscsi.c:2888:27: error: initialization of 'int (*)(struct scsi_cmnd *)' from incompatible pointer type 'int (*)(struct Scsi_Host *)' [-Werror=incompatible-pointer-types]
.eh_host_reset_handler = acornscsi_host_reset,
This removes one the extraneous opening brace and reverts the
argument type change.
[mkp: fixed checkpatch complaint]
Fixes: 74fa80ee3f ("scsi: acornscsi: move bus reset to host reset")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
bsg-lib now embeddeds the job structure into the request, and
req->special can't be used anymore.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A tiny update: one patch corrects a Kconfig problem with the shift of
the SAS SMP code to BSG and the other removes a vestige of user space
target mode.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=nBuB
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"A tiny update: one patch corrects a Kconfig problem with the shift of
the SAS SMP code to BSG and the other removes a vestige of user space
target mode"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: scsi_transport_sas: select BLK_DEV_BSGLIB
scsi: Remove Scsi_Host.uspace_req_q
- removal of the old dma_alloc_noncoherent interface
- remove unused flags to dma_declare_coherent_memory
- restrict OF DMA configuration to specific physical busses
- use the iommu mailing list for dma-mapping questions and
patches
-----BEGIN PGP SIGNATURE-----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=qHNs
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.14' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- removal of the old dma_alloc_noncoherent interface
- remove unused flags to dma_declare_coherent_memory
- restrict OF DMA configuration to specific physical busses
- use the iommu mailing list for dma-mapping questions and patches
* tag 'dma-mapping-4.14' of git://git.infradead.org/users/hch/dma-mapping:
dma-coherent: fix dma_declare_coherent_memory() logic error
ARM: imx: mx31moboard: Remove unused 'dma' variable
dma-coherent: remove an unused variable
MAINTAINERS: use the iommu list for the dma-mapping subsystem
dma-coherent: remove the DMA_MEMORY_MAP and DMA_MEMORY_IO flags
dma-coherent: remove the DMA_MEMORY_INCLUDES_CHILDREN flag
of: restrict DMA configuration
dma-mapping: remove dma_alloc_noncoherent and dma_free_noncoherent
i825xx: switch to switch to dma_alloc_attrs
au1000_eth: switch to dma_alloc_attrs
sgiseeq: switch to dma_alloc_attrs
dma-mapping: reduce dma_mapping_error inline bloat
First, number of CPUs can't be negative number.
Second, different signnnedness leads to suboptimal code in the following
cases:
1)
kmalloc(nr_cpu_ids * sizeof(X));
"int" has to be sign extended to size_t.
2)
while (loff_t *pos < nr_cpu_ids)
MOVSXD is 1 byte longed than the same MOV.
Other cases exist as well. Basically compiler is told that nr_cpu_ids
can't be negative which can't be deduced if it is "int".
Code savings on allyesconfig kernel: -3KB
add/remove: 0/0 grow/shrink: 25/264 up/down: 261/-3631 (-3370)
function old new delta
coretemp_cpu_online 450 512 +62
rcu_init_one 1234 1272 +38
pci_device_probe 374 399 +25
...
pgdat_reclaimable_pages 628 556 -72
select_fallback_rq 446 369 -77
task_numa_find_cpu 1923 1807 -116
Link: http://lkml.kernel.org/r/20170819114959.GA30580@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
memset32() can be used to initialise these three arrays. Minor code
footprint reduction.
Link: http://lkml.kernel.org/r/20170720184539.31609-8-willy@infradead.org
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: David Miller <davem@davemloft.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas, megaraid_sas, zfcp and a host of minor updates.
The major driver change here is the elimination of the block based
cciss driver in favour of the SCSI based hpsa driver (which now drives
all the legacy cases cciss used to be required for). Plus a reset
handler clean up and the redo of the SAS SMP handler to use bsg lib.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJZscDNAAoJEAVr7HOZEZN4DWIQAK/UkkrvKpV/jLATM/yi7CoL
QidY86Hmwwl7A9HQ+2fjLfAsye0xcCzRwkucKK90IP5b4pefHhiJJfiMKAAe3TUW
xstnY5z5jaOhDG4nyJFoSm5fH5qXkMnJ8NZRK8f6Qg5yBN5dStEKqoBboNsz4KBI
md7idw0mbp5i2GXlJwSpc5eDS97GiPL6WkwgGaGKfXF1NDau0GbEdjijfz55haCD
pMhY7WJh/71RfOq/1ThXT1Z3khOlVcKXrkdO+602n7zh/klRBRtBC8m2a6xCfZPj
n7Pb/s0jhCQPd+e/Xtv7WEbY8uNOCrGoVgZ6U5EGrT5IeTfep24ackYqerjMhE63
esi4BJY8lUP9SGleLMgjYWyCHdmxBJRa7UI614DWN/H0QoGP6j/2EzGoi5Fw04vC
H8/+aqPPWZc9KUBioRYo8xWO8YgMqL2eyXY+Tc9cwxqAe2T6k/NC1zJVgDFKXfzb
QoWW4v9NNmYwf5vL/7tNgkeTMFQV66yUR7dR3SGTSk8UIrJ40ok0JyUAsDg86ZAH
BfMkWwhWQ6Byoel0Y7Ti88T49Cox/64r/I0ux06Qgg99+KpRLT7z20+GLIEHgXxg
116C39rgvYKqzc7W8RCyj8qSROuMVzg6QFbB6n+1PEsYIX2O8A2Re3jdS34q2LbX
aBDm/Lfdl4kkJrV9xY6P
=nQUG
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, zfcp and a host of minor updates.
The major driver change here is the elimination of the block based
cciss driver in favour of the SCSI based hpsa driver (which now drives
all the legacy cases cciss used to be required for). Plus a reset
handler clean up and the redo of the SAS SMP handler to use bsg lib"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (279 commits)
scsi: scsi-mq: Always unprepare before requeuing a request
scsi: Show .retries and .jiffies_at_alloc in debugfs
scsi: Improve requeuing behavior
scsi: Call scsi_initialize_rq() for filesystem requests
scsi: qla2xxx: Reset the logo flag, after target re-login.
scsi: qla2xxx: Fix slow mem alloc behind lock
scsi: qla2xxx: Clear fc4f_nvme flag
scsi: qla2xxx: add missing includes for qla_isr
scsi: qla2xxx: Fix an integer overflow in sysfs code
scsi: aacraid: report -ENOMEM to upper layer from aac_convert_sgraw2()
scsi: aacraid: get rid of one level of indentation
scsi: aacraid: fix indentation errors
scsi: storvsc: fix memory leak on ring buffer busy
scsi: scsi_transport_sas: switch to bsg-lib for SMP passthrough
scsi: smartpqi: remove the smp_handler stub
scsi: hpsa: remove the smp_handler stub
scsi: bsg-lib: pass the release callback through bsg_setup_queue
scsi: Rework handling of scsi_device.vpd_pg8[03]
scsi: Rework the code for caching Vital Product Data (VPD)
scsi: rcu: Introduce rcu_swap_protected()
...
Pull parisc updates from Helge Deller:
"Major changes include:
- Full support of the firmware Page Deallocation Table with
MADV_HWPOISON and MADV_SOFT_OFFLINE. A kernel thread scans
regularily for new bad memory pages.
- Full support for self-extracting kernel.
- Added UBSAN support.
- Lots of section mismatch fixes across all parisc drivers.
- Added examples for %pF and %pS usage in printk-formats.txt"
* 'parisc-4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux: (28 commits)
printk-formats.txt: Add examples for %pF and %pS usage
parisc: Fix up devices below a PCI-PCI MegaRAID controller bridge
parisc/core: Fix section mismatches
parisc/ipmi_si_intf: Fix section mismatches on parisc platform
parisc/input/hilkbd: Fix section mismatches
parisc/net/lasi_82596: Fix section mismatches
parisc/serio: Fix section mismatches in gscps2 and hp_sdc drivers
parisc: Fix section mismatches in parisc core drivers
parisc/parport_gsc: Fix section mismatches
parisc/scsi/lasi700: Fix section mismatches
parisc/scsi/zalon: Fix section mismatches
parisc/8250_gsc: Fix section mismatches
parisc/mux: Fix section mismatches
parisc/sticore: Fix section mismatches
parisc/harmony: Fix section mismatches
parisc: Wire up support for self-extracting kernel
parisc: Make existing core files reuseable for bootloader
parisc: Add core code for self-extracting kernel
parisc: Enable UBSAN support
parisc/random: Add machine specific randomness
...
Without CONFIG_BLK_DEV_BSGLIB, we get a link error here:
drivers/scsi/scsi_transport_sas.o: In function `sas_bsg_initialize':
scsi_transport_sas.c:(.text+0xcc0): undefined reference to `bsg_setup_queue'
scsi_transport_sas.c:(.text+0xd10): undefined reference to `bsg_setup_queue'
drivers/scsi/scsi_transport_sas.o: In function `sas_smp_dispatch':
scsi_transport_sas.c:(.text+0xe8c): undefined reference to `bsg_job_done'
This modifies the Kconfig 'select' statement accordingly, and matching
what we do for the other two scsi_transport implementations that use
bsglib.
Fixes: 651a013649 ("scsi: scsi_transport_sas: switch to bsg-lib for SMP passthrough")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A patch I wrote myself several years ago removed SCSI target support
from the code under drivers/scsi. That patch removed the code that sets
uspace_req_q to a non-NULL value. Hence also remove the code that
depends on uspace_req_q != NULL.
References: commit 0664652513 ("tgt: removal")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
DMA_MEMORY_IO was never used in the tree, so remove it. That means there is
no need for the DMA_MEMORY_MAP flag either now, so remove it as well and
change dma_declare_coherent_memory to return a normal errno value.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
One of the two scsi-mq functions that requeue a request unprepares a
request before requeueing (scsi_io_completion()) but the other function
not (__scsi_queue_insert()). Make sure that a request is unprepared
before requeuing it.
Fixes: commit d285203cf6 ("scsi: add support for a blk-mq based I/O path.")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Damien Le Moal <damien.lemoal@wdc.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make these two member variables available in debugfs such that their
value can be verified by kernel developers. An example of the new
output:
ffff8804a513d480 {.op=READ, .cmd_flags=META|PRIO, .rq_flags=MQ_INFLIGHT|DONTPREP|IO_STAT|STATS, .atomic_flags=STARTED, .tag=17, .internal_tag=-1, .cmd=Read(10) 28 00 08 81 32 38 00 00 08 00, .retries=0, allocated 0.010 s ago}
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Requests are unprepared and reprepared when being requeued. Avoid that
requeuing resets .jiffies_at_alloc and .retries by initializing these
two member variables from inside scsi_initialize_rq() and by preserving
both member variables when preparing a request. This patch affects the
requeuing behavior of both the legacy scsi and the scsi-mq code paths.
Reported-by: Brian King <brking@linux.vnet.ibm.com>
References: https://lkml.org/lkml/2017/8/18/923 ("Re: [BUG][bisected 270065e] linux-next fails to boot on powerpc")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Brian King <brking@linux.vnet.ibm.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a pass-through request is submitted then blk_get_request()
initializes that request by calling scsi_initialize_rq(). Also call this
function for filesystem requests. Introduce CMD_INITIALIZED to keep
track of whether or not a request has already been initialized.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Brian King <brking@linux.vnet.ibm.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After relogin is sucessful, "send_els_logo" flag needs to be
reinitialized. This will allow next re-login to happen successfully.
In target mode, this flag was not reset correctly, causing IO's failure
during reset recovery and port ON/OFF test cases from initiator.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Darren Trap <darren.trap@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since commit 7401bc18d1 ("scsi: qla2xxx: Add FC-NVMe command
handling") we make use of 'struct nvmefc_fcp_req' in
qla24xx_nvme_iocb_entry() without including linux/nvme-fc-driver.h where
it is defined.
Add linux/nvme-fc-driver.h (and scsi/fc/fc_fs.h as nvme-fc-driver.h
needs the definition of 'struct fc_ba_rjt' from scsi/fc/fc_fs.h) to the
header files included by qla_isr.c.
Fixes: 7401bc18d1 ("scsi: qla2xxx: Add FC-NVMe command handling")
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The value of "size" comes from the user. When we add "start + size" it
could lead to an integer overflow bug.
It means we vmalloc() a lot more memory than we had intended. I believe
that on 64 bit systems vmalloc() can succeed even if we ask it to
allocate huge 4GB buffers. So we would get memory corruption and likely
a crash when we call ha->isp_ops->write_optrom() and ->read_optrom().
Only root can trigger this bug.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=194061
Cc: <stable@vger.kernel.org>
Fixes: b7cc176c9e ("[SCSI] qla2xxx: Allow region-based flash-part accesses.")
Reported-by: shqking <shqking@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
aac_convert_sgraw2() kmalloc memory and return -1 on error, which should
be -ENOMEM. However, nobody is checking return value, so with this
change, -ENOMEM is propagated to upper layer.
Signed-off-by: Nikola Pajkovsky <npajkovsky@suse.cz>
Reviewed-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
unsigned long byte_count = 0;
nseg = scsi_dma_map(scsicmd);
if (nseg < 0)
return nseg;
if (nseg) {
...
}
return byte_count;
is equal to
unsigned long byte_count = 0;
nseg = scsi_dma_map(scsicmd);
if (nseg <= 0)
return nseg;
...
return byte_count;
No other code has changed.
[mkp: fix checkpatch complaints]
Signed-off-by: Nikola Pajkovsky <npajkovsky@suse.cz>
Reviewed-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When storvsc is sending I/O to Hyper-v, it may allocate a bigger buffer
descriptor for large data payload that can't fit into a pre-allocated
buffer descriptor. This bigger buffer is freed on return path.
If I/O request to Hyper-v fails due to ring buffer busy, the storvsc
allocated buffer descriptor should also be freed.
[mkp: applied by hand]
Fixes: be0cf6ca30 ("scsi: storvsc: Set the tablesize based on the information given by the host")
Cc: <stable@vger.kernel.org>
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Three minor fixes: a NULL deref in qedf, an off by one in sg and a fix
to IPR to prevent an error on initialisation.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=+Yu6
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Three minor fixes: a NULL deref in qedf, an off by one in sg and a fix
to IPR to prevent an error on initialisation"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qedf: Fix a potential NULL pointer dereference
scsi: sg: off by one in sg_ioctl()
scsi: ipr: Set no_report_opcodes for RAID arrays
Simplify the SMP passthrough code by switching it to the generic bsg-lib
helpers that abstract away the details of the request code, and gets
drivers out of seeing struct scsi_request.
For the libsas host SMP code there is a small behavior difference in
that we now always clear the residual len for successful commands,
similar to the three other SMP handler implementations. Given that
there is no partial command handling in the host SMP handler this should
not matter in practice.
[mkp: typos and checkpatch fixes]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The SAS transport class will do the right thing and not register the BSG
node if now smp_handler method is present.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The SAS transport class will do the right thing and not register the BSG
node if now smp_handler method is present.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The SAS code will need it. Also mark the name argument const to match
bsg_register_queue.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduce struct scsi_vpd for the VPD page length, data and the RCU head
that will be used to free the VPD data. Use kfree_rcu() instead of
kfree() to free VPD data. Move the VPD buffer pointer check inside the
RCU read lock in the sysfs code. Only annotate pointers that are shared
across threads with __rcu. Use rcu_dereference() when dereferencing an
RCU pointer. This patch suppresses about twenty sparse complaints about
the vpd_pg8[03] pointers. This patch also fixes a race condition, namely
that updating of the VPD pointers and length variables in struct
scsi_device was not atomic with reference to the code reading these
variables. See also "Does the update code tolerate concurrent accesses?"
in Documentation/RCU/checklist.txt.
Fixes: commit 09e2b0b146 ("scsi: rescan VPD attributes")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Shane Seymour <shane.seymour@hpe.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Shane Seymour <shane.seymour@hpe.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduce the scsi_get_vpd_buf() and scsi_update_vpd_page()
functions. The only functional change in this patch is that if updating
page 0x80 fails that it is attempted to update page 0x83.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Shane Seymour <shane.seymour@hpe.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Shane M Seymour <shane.seymour@hpe.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This fixes a potential race condition observed on Power systems.
Several places throughout the aacraid driver call aac_fib_send or
similar to send a command to the aacraid adapter, then check the return
code to determine if the command was actually sent to the adapter, then
update the phase field in the scsi command scratch pad area to track
that the firmware now owns this command. However, there is nothing that
ensures that by the time the aac_fib_send function returns and we go to
write to the scsi command, that the command hasn't already completed and
the scsi command has been freed. This was causing random crashes in the
TCP stack which was tracked down to be caused by memory that had been a
struct request + scsi_cmnd being now used for an skbuff. Memory
poisoning was enabled in the kernel to debug this which showed that the
last owner of the memory that had been freed was aacraid and that it was
a struct request. The memory that was corrupted was the exact data
pattern of AAC_OWNER_FIRMWARE and it was at the same offset that aacraid
writes, which is scsicmd->SCp.phase. The patch below resolves this
issue.
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Tested-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A merge error crept in when formatting commit af167bc ("scsi: qlogicpti:
move bus reset to host reset")
Fixes: af167bc ("scsi: qlogicpti: move bus reset to host reset")
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The > here should be >= or we end up reading one element beyond the end
of the qedi->itt_map[] array. The qedi->itt_map[] array is allocated in
qedi_alloc_itt().
Fixes: ace7f46ba5 ("scsi: qedi: Add QLogic FastLinQ offload iSCSI driver framework.")
Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is an interesting regression with gcc-8, showing a harmless warning
for correct code:
In file included from include/linux/kernel.h:13:0,
...
from drivers/scsi/lpfc/lpfc_debugfs.c:23:
include/linux/printk.h:301:2: error: 'eq' may be used uninitialized in this function [-Werror=maybe-uninitialized]
printk(KERN_ERR pr_fmt(fmt), ##__VA_ARGS__)
^~~~~~
In file included from drivers/scsi/lpfc/lpfc_debugfs.c:58:0:
drivers/scsi/lpfc/lpfc_debugfs.h:451:31: note: 'eq' was declared here
I managed to reduce the warning into a small test case for gcc-8 that I
reported in the gcc bugzilla[1].
As a workaround, this changes the logic to move the two assignments of
'eq' out of the conditions and instead make the index conditional. This
works for all configurations I tried and avoids adding a bogus
initialization.
Acked-by: James Smart <james.smart@broadcom.com>
Link: [1] https://gcc.gnu.org/bugzilla/show_bug.cgi?id=81958
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The only reference to lpfc_nvmet_replenish_context() is inside of an
disabled:
drivers/scsi/lpfc/lpfc_nvmet.c:1457:1: error: 'lpfc_nvmet_replenish_context' defined but not used [-Werror=unused-function]
This replaces the preprocessor conditional with a C condition, so the
compiler can see that the function is intentionally unused.
Fixes: 9a38e4f1c82f ("scsi: lpfc: Fix MRQ > 1 context list handling")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ioctl DK_CAPI_VLUN_RESIZE can fail if the allocated vlun size is
reduced from almost maximum capacity and then increased again.
The shrink_lxt() routine is currently using the SISL_ASTATUS_MASK to
mask the higher 48 bits of the lxt entry. This is unnecessary and
incorrect as it uses a mask designed for the asynchronous interrupt
status register. When the 4 port support was added to cxlflash, the
SISL_ASTATUS_MASK was updated to reflect the status bits for all 4
ports. This change indirectly affected the shrink_lxt() code path.
To extract the base, simply shift the bits without masking.
Fixes: 5651807232 ("scsi: cxlflash: SISlite updates to support 4 ports")
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The AFU recovery routine uses an interruptible mutex to control the flow
of in-flight recoveries. Upon receiving an interruptible signal the code
branches to a common exit path which wrongly assumes the mutex is
held. Add a local variable to track when the mutex should be unlocked.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The AFU termination sequence has been refactored over time such that the
main tear down routine, term_afu(), can no longer can be invoked with a
NULL AFU pointer. Remove the unnecessary existence check from
term_afu().
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
vio_device_id are not supposed to change at runtime. All functions
working with vio_device_id provided by <asm/vio.h> work with const
vio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The kerneldoc comment for scsi_initialize_rq() neglected to document the
"rq" parameter, leading to this docs build warning:
./drivers/scsi/scsi_lib.c:1116: warning: No description found for parameter 'rq'
Document the parameter and make the build slightly quieter.
[mkp: used wording suggested by Bart]
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently we free the resources backing the enclosure device before we
call device_unregister(). This is racy: during rmmod of low-level SCSI
drivers that hook into enclosure, we end up with a small window of time
during which writing to /sys can OOPS. Example trace with mpt3sas:
general protection fault: 0000 [#1] SMP KASAN
Modules linked in: mpt3sas(-) <...>
RIP: [<ffffffffa0388a98>] ses_get_page2_descriptor.isra.6+0x38/0x220 [ses]
Call Trace:
[<ffffffffa0389d14>] ses_set_fault+0xf4/0x400 [ses]
[<ffffffffa0361069>] set_component_fault+0xa9/0xf0 [enclosure]
[<ffffffff8205bffc>] dev_attr_store+0x3c/0x70
[<ffffffff81677df5>] sysfs_kf_write+0x115/0x180
[<ffffffff81675725>] kernfs_fop_write+0x275/0x3a0
[<ffffffff8151f810>] __vfs_write+0xe0/0x3e0
[<ffffffff8152281f>] vfs_write+0x13f/0x4a0
[<ffffffff81526731>] SyS_write+0x111/0x230
[<ffffffff828b401b>] entry_SYSCALL_64_fastpath+0x13/0x94
Fortunately the solution is extremely simple: call device_unregister()
before we free the resources, and the race no longer exists. The driver
core holds a reference over ->remove_dev(), so AFAICT this is safe.
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Acked-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make these const as they are only stored in the type field of a device
structure, which is const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
gd->minors has been set when call alloc_disk() in sd_probe.
Signed-off-by: weiping zhang <zhangweiping@didichuxing.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Just displaying some different information; drop it.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
megaraid_mbox only has one reset function, and that is a host reset. So
drop the duplicate bus reset and device reset functions.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Never used anywhere.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
bus reset always returns SUCCESS, meaning host reset was never
tested. At the same time the only difference to the HBA is a missing
call to NCR_700_chip_reset(). So add the missing call to bus reset,
drop host reset, and move bus reset to host reset.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver has both a bus and a host reset, where the host reset does a
bus reset followed by an attempt to reset the chip registers to a
default state. However, as the bus reset always returned SUCCESS the
host reset was never called, so the functionality of the register reset
function was never validated. Additionally, tha AIC-6260 chip has a
hard reset line, which actually should be preferred for a host
reset. But I haven't found a way how this can be triggered via software,
so take the safe approach and drop the host reset.
[mkp: typo]
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
bus reset is a host reset without nsp32hw_init(), and will always return
SUCCESS, thus disabling the use of host reset. So drop bus reset in
favour of host reset.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
qedf has a host reset handler, but as the bus reset handler is a stub
always returning SUCCESS the host reset is never invoked. So drop the
bus reset handler.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Tested-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
bus_reset and host_reset are the same functions, so drop bus_reset.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
host_reset and bus_reset is the same function, so drop bus reset.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The bus reset handler is really a host reset.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The bus reset handler really is a host reset, so move it to
eh_bus_reset_handler.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The bus reset function is really a host reset, so move it to
eh_host_reset_handler.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The bus reset function really is a host reset, so move it to
eh_host_reset_handler().
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The bus reset function is just a wrapper calling host reset under the
host lock. So move taking of the host lock into the host reset function
and drop bus reset.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The bus reset function really is a host reset, so move it to
eh_host_reset_handler().
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The Highpoint driver only has one reset function, and that is a host
reset. So stop pretending we're doing anything else.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The bus reset handler is just calling target reset on all targets, which
is exactly what SCSI EH will be doing anyway. So move the bus reset
function to target reset and drop the loop.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The bus reset handler is calling I_T Nexus reset, which logically is a
target reset as it need to specify both the initiator and the target.
So move it to target reset.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Command abort already returns FAILED, which will then be escalated to a
host reset. So no need to call host_reset directly.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When calling host reset we're resetting all ports anyway, so there is no
point in waiting for the ports to become unblocked.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When we're resetting the host any remote port states will be reset
anyway, so it's pointless to wait for dev_loss_tmo during host reset.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The function returns '0' if successful; with the original comment
the function doesn't have a way to indicate success ...
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Bart van Assche <bvanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that gcc reports the following warning when
building with W=1:
drivers/scsi/iscsi_tcp.c:166:24: warning: variable ?session? set but not used [-Wunused-but-set-variable]
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Cc: Lee Duncan <lduncan@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that gcc reports the following warning when
building with W=1:
drivers/scsi/scsi_debug.c:2264:15: warning: variable ?pcontrol? set but not used [-Wunused-but-set-variable]
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avoid that the following compiler warning is reported when building
with W=1:
drivers/scsi/scsi_transport_srp.c:92:19: warning: comparison is always false due to limited range of data type [-Wtype-limits]
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Check whether memory allocation succeeded before dereferencing
the pointer to the allocated memory.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This was detected by building with W=1.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that smatch reports the following:
drivers/scsi/libiscsi.c:1081: iscsi_handle_reject() warn: inconsistent indenting
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avoid that sparse reports the following:
drivers/scsi/sg.c:1114:41: warning: incorrect type in argument 5 (different address spaces)
drivers/scsi/sg.c:1114:41: expected char [noderef] <asn:1>*arg
drivers/scsi/sg.c:1114:41: got char *<noident>
This patch does not change any functionality.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that gcc reports the following warning when
building with W=1:
drivers/scsi/sd.c:315:10: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
if (val >= 0 && val <= T10_PI_TYPE3_PROTECTION)
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that smatch reports the following:
drivers/scsi/sd.c:3540: sd_suspend_common() warn: inconsistent indenting
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Before scsi_prep_fn() calls the ULP .init_command() callback
function it stores the SCSI command pointer in request.special.
This means that the SCpnt = rq->special assignments in the sd
and sr drivers assign a pointer to itself. Hence convert these
two assignment statements into warning statements.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since commit e9c787e65c ("scsi: allocate scsi_cmnd structures as
part of struct request") struct request and struct scsi_cmnd are
adjacent. This means that there is now an alternative to reading
req->special to convert a pointer to a prepared request into a
SCSI command pointer, namely by using blk_mq_rq_to_pdu(). Make
this change where appropriate. Although this patch does not
change any functionality, it slightly improves performance and
slightly improves readability.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rename several functions to make it easy to see which queue type a
function is intended for.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that smatch reports the following warning:
drivers/scsi/scsi_sysfs.c:117: check_set() error: strncmp() '"-"' too small (2 vs 20)
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The conclusion of a recent discussion about the new warnings
reported by gcc 7 is that the new warnings reported when building
with W=1 should be suppressed. However, gcc 7 still warns about
fall-through in switch statements when building with W=1. Suppress
these warnings by annotating the SCSI core properly.
See also Linus Torvalds, Lots of new warnings with gcc-7.1.1, 11
July 2017 (https://www.mail-archive.com/linux-media@vger.kernel.org/msg115428.html).
References: commit bd664f6b3e ("disable new gcc-7.1.1 warnings for now")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update driver version to 11.4.0.3
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
cc1: warnings being treated as errors
drivers/scsi/lpfc/lpfc_init.c: In function 'lpfc_get_wwpn':
drivers/scsi/lpfc/lpfc_init.c:3253: error: integer constant is too large for 'long' type
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add Buffer to buffer credit recovery support to the driver. This is a
negotiated feature with the peer that allows for both sides to detect
dropped RRDY's and FC Frames and recover credit.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change hw queue binding messages to info - not error.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Port issue was fixed, the hbacmd reset would take more than 8 minutes to
complete.
There were conflicting NVME SGL posting/reposting responsibilities
between lpfc_online()/lpfc_sli4_hba_setup() and
lpfc_nvme_create_localport(). The lpfc_online() causes a REPOST on
existing NVME SGLs which is not released during the fc port reset.
However, lpfc_nvme_create_localport() wants to allocate new NVME buffers
and post them. Both cancelled out each other which had a side effect of
hosing the mailbox handling that was used to remove the sgl lists -
causing multiple 60s mbx timeouts.
Fix by preserving all SGL lists over the fc port reset.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The nonrecovery occurred because the lpfc nvme initiator function did
not reestablish its localport creation with the nvme host transport in
lpfc_oneline. Because of that, an NVME rport binding could not take
place.
Corrected by recreating the localport in the adapter reset recovery
routine.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the nvmet_fc transport breaks an io into multiple sequences, the
driver will improperly set the relative offset on the 2nd through N
sequences.
Correct by properly formatting the hw cmd so the relative offset is
picked up from the hw cmd.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Various oops including cpu LOCKUPs were seen.
For asynchronously received ius where the driver must assign exchange
resources, the resources were on a single get (free) list and put list
(finished, waiting to be put on get list). As all cpus are sharing the
lists, an interrupt for a receive frame may have to wait for all the
other cpus to place their done work onto the put list before it can
acquire the lock to pull from the list.
Fix by breaking the resource lists into per-cpu lists or at least more
than 1 list with cpu's sharing the lists). A cpu would allocate from the
free list for its own cpu, and put its done work on the its own put list
- avoiding the contention. As cpu load may vary, when empty, a cpu may
grab from another cpu, thereby changing resource distribution. But
searching for a resource only occurs on 1 or a few cpus until a single
resource can be allocated. if the condition reoccurs, it starts looking
at a different cpu.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Various oops being seen on being in the ISR too long and cpu lockups,
when under heavy load.
The amount of work being posted off of completion queues kept the ISR
running almost all the time
Correct the issue by limiting the amount of work per iteration.
[mkp: typo]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When using fabric-assigned WWNs, the switch doesn't like copy of the
FLOGI payload, which includes valid VVL bits, to be used as the FDISC
payload.
Rather than wait for corrected switch firmware, ensure the VVL bits are
marked invalid on FDISCs.
[mkp: typo]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A race condition was found whereby the initiator would receive the RSCN
for a new NVME device before it had a chance to register its FC4 support
with the fabric. Thus, when queried by the initiator, it would see that
the target supported FC-NVME.
Corrected by making the assumption that the target always supports
FC-NVME thus a PRLI is sent. It's ok for the target to reject it.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In adapter reset tests, an oops was seen with a NULL pointer in
lpfc_free_rq_buffer+0x20/0x60
The driver is failing to properly repost the nvmet sgl list when
recovering from the reset. Thus the driver eventually trys to walk an
errant buffer list.
Corrected the sgl buffer recovery as well as strengthening the
initialization of the bufferlist.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After lip, the driver sometimes would have two rports for the same
device, allowing the namespaces to be duplicated by nvme.
In lpfc_plogi_confirm_nport() the driver was not swapping the nrport
maintained by the ndlp's undergoing address swapping. This allowed the
2nd rport to sneak in as it was considered a separate device.
This patch adds the fixes to Swap the nrport in each ndlp and take care
of the reference counts on the ndlps similar to FCP rports.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After link bounce in a NVME Pt2Pt config, the driver managed to map the
same nport twice, resulting in multiple device nodes for the same
namespace.
In Pt2Pt, the driver must send PRLI's for both (scsi) FCP and NVME
rather than using fabric aids. The driver was inconsistent on handling
various PRLI completions, especially rejects, which had reject codes
cross the different protocol PRLI completions.
Fixed to perform the following: if nvmet mode (fc port can only be a
nvme target) - rejects all unsolicitly FCP PRLI's. Never issues a FCP
PRLI.
The multiple protocol PRLI's are sent simultaneously. However, driver
will now only state transition after both PRLI's are complete. New flags
were added to aid tracking the responses from the different PRLI's.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Modify driver return error codes to align with host nvme transport.
Driver isn't returning Exxx error codes to properly reflect out of
resource or connectivity conditions (-EBUSY), yet there were hard error
conditions returning -EBUSY.
Ensure the following situations return the proper return code:
- Temporary failures or temporary resource availability: -EBUSY
- Connectivity issues: -ENODEV
All others are treated as hard errors and return an -Exxx value that
indicates the type of error.
Also, lpfc_sli4_issue_wqe() was modified to not translate error from
-Exxx to WQE state. This allows lpfc_nvme_fcp_io_submit() routine to
just return whatever -E value was returned from other routines.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Transitioned some informational discovery messages to now always be
displayed when log_verbose is set.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
lpfc oops when it discovers a NVME target but is configured for SCSI
only operation. Oops is in lpfc_nvme_register_port+0x33/0x300.
The localport is not valid so it should not have been referenced.
Added validity check for localport
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the switch blade is pulled out then plugged back in, the driver
does not issue a PLOGI to the target
When the switch blade is pulled out, it does not reset the link. The
driver ends up issuing a LOGO to the target, and finally sees devloss.
Since the driver believes that a LOGO is outstanding, it does not issue
a PLOGI to the target upon link up
Correct by placing the ndlp in UNUSED state When devloss happens in
LOGO_ISSUE state.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver does not discover targets when in loop mode.
The NLP type is correctly getting set when a fabric connection is
detected but, not for loop. The unknown NLP type means that the driver
does not issue a PRLI when in loop topology. Thus target discovery
fails.
Fix by checking the topology during discovery. If it is loop, set the
NLP FC4 type to FCP.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Message "0271 Illegal State Transition: node" seen in logs, all luns are
unuseable for that target.
A window exists in the rcv_plogi path where if the state is plogi issue
but the driver has not issued a plogi, then two reglogins will be sent
for the same RPI. The first one to complete will advance the state to
prli issue the second one will be detected as an illegal state, and
leave the node in an unusable state.
Correct the completion routine for the PLOGI ACC that detects the state
change when the driver starts discovery on the node again and drop the
REGLOGIN mailbox command.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If there are IO's running and host reset or chip reset is triggered,
IO's can fail due to rport time out. During chip reset recovery process,
driver notifies the transport layer that remote port no longer exist, by
calling fc_remote_port_delete(). When this function is called, it
actually delays deletion by "blocking" it. It sets the remote port state
to "FC_PORTSTATE_BLOCKED" and sets FC_RPORT_DEVLOSS_PENDING. When
driver tries to abort the command by calling its abort handler function,
abort handler will wait until remote port state is blocked state or wait
for dev_loss_tmo time. Due to this blocking, rport times out and results
in an IO failure. This patch adds a check for any active reset process
before calling abort handler function.
[mkp: typo]
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If queue count is zero while reading FW dump template, for entry
T263/T274, skip capturing those entries during FW dump capture.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When RSCN is delivered for specific remote port. Use ADISC to verify the
session is still valid or not.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ql2xmaxqdepth is the module parameter that seeds the per target
queue depth in the Scsi midlayer (sdev->queue_depth). Performance
testing revealed that increasing this value would improve IOPS
numbers under certain workloads.
Signed-off-by: Michael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When we tear down the NPIV host configuration in target mode, the
qla_tgt struct was left dangling on the global list. This patch cleans
up link list and frees memory.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If SNS fabric login fails, set loop resync flag to retry via dpc.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Calling sp->free() ensures the context-correct free routine is called.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SFP can come in 2 formats: short range/SR and long range/LR. For LR,
user the can increase the number of Buffer to Buffer credits between end
points via Cavium's command line tool. By default, FW uses a lower BB
Credit value optimized for SR. This patch will read the SFP for each
link up event and during chip reset sequence. If the SFP type and
setting are mismatch, then the chip is reset 1 time to use the
appropriate setting.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The Get Port Speed switch command needs the fabric port name of the
remote device. Current code uses the registered WWPN.
Fixes: 726b854870 ("qla2xxx: Add framework for async fabric discovery")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update ha->wq max_active from 1 to default. MQ interrupts are queued up
via this work queue. This allows interrupts to be process in parrallel,
instead of serialized by the work queue.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove extra register read for each interrupt for performance
improvement.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For NPIV ports, call configure_hba() so that NPIV ports can proceed to
loop initialization.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If FA-WWPN feature disabled on the switch side and enabled for the
adapter, then driver would update the port name with switch port name.
This patch fixes issue by checking correct BIT flag to validate.
Fixes: 41dc529a46 ("qla2xxx: Improve RSCN handling in driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver will perform following
- Set PFLG_DRIVER_REMOVING flag and do not disable PCIe error reporting
during adapter shutdown.
- If PCIe device count is already zero, return correct error type from
PCI error interface.
- When device is offline, return correct error type from PCIe error
path.
- If there is board disable thread active during shutdown and PCIe
device count is zero then cancel scheduling board disable thread
during shutdown and return.
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Darren Trap <darren.trap@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver held spinlocks during callbacks for NVME errors which
resulted in a deadlock because recovery LS cmds needed the same lock.
Signed-off-by: Duane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Following error will be logged in to message file while trying to
configure target with multiqueue.
"Cmd 0x1f aborted with timeout since ISP Abort is pending"
"qla25xx_init_queues Rsp que: 1 init failed."
Fixes: 82de802ad4 ("scsi: qla2xxx: Preparation for Target MQ.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Michael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix incorrect second argument for wait_event_timeout()
Fixes: c4a9b538ab ("qla2xxx: Allow vref count to timeout on vport delete.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After a kill adapter, since the cmd_status is not set, the IOCTLs will
be hung in driver resulting in application hang. Set cmd_status
MFI_STAT_WRONG_STATE when completing pended IOCTLs.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver's local RAID map is accessed frequently. We will first try to get
memory from __get_free_pages. If this fails, fall back to using vmalloc.
For crash dump buffers always prefer vmalloc.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In TM code, smid_task is valid only in case of task aborts.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
megasas_wait_for_outstanding_fusion checks for pending commands every 1
second. But megasas_complete_cmd_dpc_fusion is only called every 5
seconds. If the commands are already completed by firmware, there is an
additional delay of 5 seconds before driver will process completion for
these commands.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Similar to task abort case, use synchronize_irq API in target reset
case. Also, remove redundant call to megasas_complete_cmd_dpc_fusion
after calling megasas_sync_irqs in task abort case.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Setting resetwaittime to 0 during a FW fault will result in driver not
calling the OCR.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver allocated 256 byte MFI frames bytes but while sending MFI frame
(embedded inside chain frame of MPT frame) to firmware, driver sets the
length as 4k. This results in DMA read error messages during boot.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove variable assignments. The value stored in local variable _rc_ is
overwritten at line 2448:rc = lpfc_sli4_bsg_set_link_diag_state(phba,
0); before it can be used.
Addresses-Coverity-ID: 1226935
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Take f_mutex around mmap() processing to protect against races with the
SG_SET_RESERVED_SIZE ioctl. Ensure the reserve buffer length remains
consistent during the mapping operation, and set the "mmap called" flag
to prevent further changes to the reserved buffer size as an atomic
operation with the mapping.
[mkp: fixed whitespace]
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 1bc0eb0446 ("scsi: sg: protect accesses to 'reserved' page
array") adds needed concurrency protection for the "reserve" buffer.
Some checks that are initially made outside the lock are replicated once
the lock is taken to ensure the checks and resulting decisions are made
using consistent state.
The check that a request with flag SG_FLAG_MMAP_IO set fits in the
reserve buffer also needs to be performed again under the lock to ensure
the reserve buffer length compared against matches the value in effect
when the request is linked to the reserve buffer. An -ENOMEM should be
returned in this case, instead of switching over to an indirect buffer
as for non-MMAP_IO requests.
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The parentheses are in the wrong place so we specify the length as
"sizeof(this_device->device_id) < 0" which is zero.
Fixes: 988b87edd231 ("scsi: hpsa: Ignore errors for unsupported LV_DEVICE_ID VPD page")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
pnp_device_id are not supposed to change at runtime. All functions
working with pnp_device_id provided by <linux/pnp.h> work with const
pnp_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If scsi_host_template->host_reset is NULL and the user requests an
adapter reset through
echo adapter > /sys/class/scsi_host/hostx/host_reset
-EINVAL will be returned even though the "adapter" argument is perfectly
valid.
Change this so that we only return -EINVAL if the provided string is
invalid. If the host does not implement a ->host_reset function we'll
return -EOPNOTSUPP.
[mkp: tweaked patch description]
Signed-off-by: weiping zhang <zhangweiping@didichuxing.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
struct scsi_changer needs refcounting as the device might be removed
while the fd is still open.
[mkp: whitespace]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Refactor code in order to avoid identical code for different branches.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
pnp_device_id are not supposed to change at runtime. All functions
working with pnp_device_id provided by <linux/pnp.h> work with const
pnp_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Because we were passing 'qedf_debug' instead of 'debug' to the
MODULE_PARM_DESC() macro, modinfo listed the parameter name as 'qedf_debug'
instead of it's proper name 'debug'. Correct the parameter name.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is no ordering required for the various workqueues the driver uses
so they can be converted to regular workqueues.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently in the driver the qedf_ctx attribute vlan_hw_insert is used to
which whether to insert a VLAN tag in FIP frames (except for FIP VLAN
request which is explicitly sent out untagged at least from the driver's
point of view).
When we receive a FIP VLAN response, we set qedf->vlan_hw_insert to 0 which
makes the qedf_fip_send function insert the VLAN. However when we exhaust
our FIP VLAN retries, we do not set qedf->vlan_hw_insert to 0 which means
that the driver will not tag the FIP frame with the correct VLAN ID. The
result that was observed on the wire is that some entity either in the LL2
or L2 firmware is adding a NULL VLAN tag which can cause FIP solicitation
to fail.
The offload FCoE frame function, qedf_xmit, does not use the vlan_hw_insert
attribute to decide whether to tag frames with the FIP/FCoE VLAN. Instead
it unilaterially tags the offload frames with the VLAN ID stored in
qedf->vlan_id. This is the correct behavior so the driver can guarantee
that non-offload FIP frames go out with the correct VLAN ID.
Also use the Linux network layer helpers instead of doing the VLAN insert
manually.
Also fix setting the fallback VLAN so that it used the module parameter and
is not hardcoded to 1002 (though 1002 is the default).
[mkp: fixed typo]
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently in the driver we've been using the fc_fcoe_set_mac() function to
set the source MAC for FCoE traffic. This works well in most cases as it
uses the spec. default FCF-MAC. However, if the administrator changes the
FCF-MAC switch, then any FCoE traffic we send will be dropped by the
switch.
Instead we should check the granted MAC from the FLOGI payload and use that
address if it is present. Otherwise, fall back to using the the default
FCF-MAC and the fabric ID of the port as the FCoE MAC address.
Once this address is known we need to set it when doing non-offload
traffic, offload traffic and setting the data_src_address libfcoe uses for
FIP keep alive messages.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If dev_info.wwpn and dev_info.wwnn are set by qed use these values to set
the WWNs of the port. Otherwise fall back to the old method using
fcoe_wwn_from_mac().
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Trivial fix to variable name, sfp_additonal_info should be
sfp_additional_info (add in missing i).
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The code looks like this:
i = ntohl(aux->filemark_cnt);
if (STp->header_cache != NULL && i < OS_FM_TAB_MAX && (i > STp->filemark_cnt ||
STp->first_frame_position - 1 != ntohl(STp->header_cache->dat_fm_tab.fm_tab_ent[i]))) {
If i is negative then it's less than OS_FM_TAB_MAX so we read before
the start of the STp->header_cache->dat_fm_tab.fm_tab_ent[] array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The for loop is statement is missing an indent, add it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
An optional discovery status should be printed with a pr_cont and needs
a leading space to make it more readable. The final new line should also
be a pr_cont and the indentation is out by one, so fix that too.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Simple subenclosures do not need to support SES page 2, so make it
optional.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The printk was using the result as argument, leading to a slightly
confusing log message.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We should be checking the return code from ses_recv_diag() to avoid
accessing invalid data.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As the cciss driver has been removed there are no overlapping
PCI IDs anymore, and the 'hpsa_allow_any' flag can be removed.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The hpsa driver now has support for all boards the cciss driver
used to support, so this patch removes the cciss driver and
make hpsa an alias to cciss.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Legacy boards might not support the 'extended' report luns format,
but as this is to be expected we don't need to print out an error here.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Legacy boards might not support the LV_DEVICE_ID VPD page, so
we shouldn't print out an error message here.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Legacy boards might not support volume status, so assume
the volume is online here.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for legacy boards, ensuring to enable the driver for
those boards only when 'hpsa_allow_any' is set.
The attribute 'legacy_board' is set to '1' if the device is
a legacy board, and '0' otherwise.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
'rc' is known to be 0 at this point. If 'create_context()' fails,
returns -ENOMEM instead of 0 which means success.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On parisc I see this UBSAN warning with a sym53c896:
UBSAN: Undefined behaviour in ./drivers/scsi/sym53c8xx_2/sym_hipd.c:762:24
index -1903078336 is out of range for type 'u32 [7]'
Avoid this warning by switching to div64_ul().
[mkp: fix typo]
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While the 'state' attribute can (and will) change occasionally,
calling 'poll()' or 'select()' on it fails as sysfs is never
notified that the state has changed.
With this patch calling 'poll()' or 'select()' will work
properly.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rework scsi_internal_device_unblock_nowait() into using a switch
statement. No functional changes.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with const
pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Bradley Grove <bgrove@attotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since switching to blk-mq as the default in commit 5c279bd9e4
("scsi: default to scsi-mq"), virtio-scsi LUNs consume about 10x as
much kernel memory.
qemu currently allocates a fixed 128 entry virtqueue. can_queue
currently is set to 1024. But with indirect descriptors, each command
in the queue takes 1 virtqueue entry, so the number of commands which
can be queued is equal to the length of the virtqueue.
Note I intend to send a patch to qemu to allow the virtqueue size to be
configured from the qemu command line.
Signed-off-by: Richard W.M. Jones <rjones@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[qed_sp_iscsi_func_start:189(host_7-0)]Cannot satisfy CQ amount. Queues
requested 8, CQs available 4. Aborting function start
Above condition will resolve as management firmware is capable of
telling us the number of CQs available for a given PF, qed will
communicate the same number to qedi, So that qedi will know how much CQs
are allowed.
Signed-off-by: Manish Rangankar <manish.rangankar@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver version is not updated with changes to the driver, so it has
no value, so just get rid of it.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instances of kfree(shost) should be replaced with scsi_host_put().
In addition, a missing scsi_host_put() is added for error path in
hisi_sas_shost_alloc_pci() and v3 driver removal.
Signed-off-by: Pan Bian <bianpan2016@163.com> # For main.c changes
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Variable res only holds value 0, so remove it.
This cleans up a coccicheck warning.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add function to set linkrate for v3 hw.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch updates some register setting according to recommendation
from HW designer and experiment.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use ACPI "_RST" method to reset the controller, since FLR is not
supported.
Function hisi_sas_stop_phys() is introduced to remove some code
duplication.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
At the beginning of 'qedf_srr_compl()' and of 'qedf_rec_compl()', we
check if 'orig_io_req' is NULL. If this happens, a NULL pointer
dereference will occur in the error handling path.
Fix it by adding an additional label in the error handling path in order
to avoid this NULL pointer dereference.
[mkp: typo]
Fixes: 61d8658b4a ("scsi: qedf: Add QLogic FastLinQ offload FCoE driver framework.")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Six minor and error leg fixes, plus one major change: the reversion of
scsi-mq as the default. We're doing the latter temporarily (with a
backport to stable) to give us time to fix all the issues that turned
up with this default before trying again.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=aB/i
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Six minor and error leg fixes, plus one major change: the reversion of
scsi-mq as the default.
We're doing the latter temporarily (with a backport to stable) to give
us time to fix all the issues that turned up with this default before
trying again"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: cxgb4i: call neigh_event_send() to update MAC address
Revert "scsi: default to scsi-mq"
scsi: sd_zbc: Write unlock zone from sd_uninit_cmnd()
scsi: aacraid: Fix out of bounds in aac_get_name_resp
scsi: csiostor: fail probe if fw does not support FCoE
scsi: megaraid_sas: fix error handle in megasas_probe_one
If "val" is SG_MAX_QUEUE then we are one element beyond the end of the
"rinfo" array so the > should be >=.
Fixes: 109bade9c6 ("scsi: sg: use standard lists for sg_requests")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since ipr RAID arrays do not support the MAINTENANCE_IN /
MI_REPORT_SUPPORTED_OPERATION_CODES, set no_report_opcodes to prevent it
from being sent.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A couple of minor fixes (st, ses) and some bigger driver fixes for
qla2xxx (crash triggered by fw dump) and ipr (lockdep problems with
mq).
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=gE+M
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"A couple of minor fixes (st, ses) and some bigger driver fixes for
qla2xxx (crash triggered by fw dump) and ipr (lockdep problems with
mq)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ses: Fix wrong page error
scsi: ipr: Fix scsi-mq lockdep issue
scsi: st: fix blk_get_queue usage
scsi: qla2xxx: Fix system crash while triggering FW dump
If nud_state is not valid then call neigh_event_send() to update MAC
address.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Defaulting to scsi-mq in 4.13-rc has shown various regressions
on setups that we didn't previously consider. Fixes for them are
in progress, but too invasive to make it in this cycle. So for
now revert the commit that defaults to blk-mq for SCSI. For 4.14
we'll plan to try again with these fixes.
This reverts commit 5c279bd9e4.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Releasing a zone write lock only when the write commnand that acquired
the lock completes can cause deadlocks due to potential command
reordering if the lock owning request is requeued and not executed. This
problem exists only with the scsi-mq path as, unlike the legacy path,
requests are moved out of the dispatch queue before being prepared and
so before locking a zone for a write command.
Since sd_uninit_cmnd() is now always called when a request is requeued,
call sd_zbc_write_unlock_zone() from that function for write requests
that acquired a zone lock instead of from sd_done(). Acquisition of a zone
lock by a write command is indicated using the new command
flag SCMD_ZONE_WRITE_LOCK.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <Bart.VanAssche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We terminate the aac_get_name_resp on a byte that is outside the bounds
of the structure. Extend the return response by one byte to remove the
out of bounds reference.
Fixes: b836439faf ("aacraid: 4KB sector support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David Carroll <david.carroll@microsemi.com>
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fail probe if FCoE capability is not enabled in the firmware.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
megasas_mgmt_info.max_index has increased by 1 before megasas_io_attach,
if megasas_io_attach return error, then goto fail_io_attach,
megasas_mgmt_info.instance has a wrong index here. So first reduce
max_index and then set that instance to NULL.
Signed-off-by: weiping zhang <zhangweiping@didichuxing.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds calls to kill CQ takslets v3 hw during probe failure.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The channel interrupt is to process all the interrupts except PHY
UP/DOWN and broadcast interrupt. So we need to clear all the interrupts
except those 3 interrupts after processing channel interrupts.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Modify STP link timer from 10ms to 500ms. Also add the register address.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For v3 hw, internal abort function required status and command buffer to
be set, so add necessary code for this.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add two ATA commands, ATA_CMD_ZAC_MGMT_IN and ATA_CMD_ZAC_MGMT_OUT in
hisi_sas_get_ata_protocol(), to support SATA SMR disk.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch is a fix related to freeing a device in v2 hw driver.
Before, we polled to ITCT CLR interrupt to check if a device is free.
This was error prone, as if the interrupt doesn't occur in 10us, we miss
processing it.
To avoid this situation, service this interrupt and sync the event with
a completion.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds support to clean-up allocated IRQs and kill tasklets
when probe fails and for driver removal.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch removes some repeated configurations:
(1) The device id of the device is already set in the alloc function, so
we don't need to modify in free device function.
(2) Field dev_type and dev_status are configured in hisi_sas_dev_gone(),
so there is no need for repeated config in free_device_v3_hw.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The code to print ECC errors in v2 hw driver is very repetitive. This
patch condensed the code by looping an array of errors.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add DFX feature for v2 hw. We are adding support for
the following errors:
- loss_of_dword_sync_count
- invalid_dword_count
- phy_reset_problem_count
- running_disparity_error_count
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The value dw0 is the residual bytes when UNDERFLOW error happens, but we
filled the residual with the value of dw3 before. So change the residual
from dw3 to dw0.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When some interrupts happen together, we need to process every interrupt
one-by-one, and should not return immediately when one interrupt process
is finished being processed.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch provides fixes for the following issues:
1. Fix issue of controller reset required to send commands. For reset
process, it may be required to send commands to the controller, but
not during soft reset. So add HISI_SAS_NOT_ACCEPT_CMD_BIT to prevent
executing a task during this period.
2. Send a broadcast event in rescan topology to detect any topology
changes during reset.
3. Previously it was not ensured that libsas has processed the PHY up
and down events after reset. Potentially this could cause an issue
that we still process the PHY event after reset. So resolve this by
flushing shot workqueue in LLDD reset.
4. Port ID requires refresh after reset. The port ID generated after
reset is not guaranteed to be the same as before reset, so it needs
to be refreshed for each device's ITCT.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the driver’s PCI IDs to match the latest Microsemi controllers
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add PQI reset to driver shutdown callback to work around controller bug.
During an 1.) OS shutdown or 2.) kexec outside of a kdump, the Linux
kernel will clear BME on our controller.
If BME is cleared during a controller/host PCIe transfer, the controller
will lock up.
So we perform a PQI reset in the driver's shutdown callback function to
eliminate the possibility of a controller/host PCIe transfer being
active when the kernel clears BME immediately after calling the driver's
shutdown callback.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- make pass-thru requests bi-directional
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- distinguish between shutdown and non-shutdown.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The null check on pHba->channel[chan].device is redundant because
device is an array and hence can never be null. Remove the check.
Detected by CoverityScan, CID#115362 ("Array compared against 0")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The return value of dma_map_single() should be checked by
dma_mapping_error(). However, in function qla26xx_dport_diagnostics(), its
return value is checked against NULL, which could result in failures.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The return value of scsi_host_alloc() should be released by
scsi_host_put(). However, in function mvs_pci_init(), kfree()
is used. This patch replaces kfree() with scsi_host_put() to avoid
possible memory leaks.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In function pm8001_pci_probe(), on errors that the control flow jumps to
label err_out_ha_free, function pm8001_free() is called. In pm8001_free(),
scsi_host_put() is called to release shost, which keeps the return value
of scsi_host_alloc(). After pm8001_free() returns, kfree() is called to
free shost again, resulting in a double free bug. This patch removes
scsi_host_put() from pm8001_free() and explicitly calls scsi_host_put()
to release Scsi_Host in need.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
fix allocate instance->pd_info twice which was introduced by 96188a89cc.
Signed-off-by: weiping zhang <zhangweiping@didichuxing.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After sending a message, always clear esp->msg_out_len. Otherwise,
eh_abort_handler may subsequently fail to send an ABORT TASK SET
message.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch improves readability. There are no functional changes.
Since this touches on a questionable ESP_INTR_DC conditional, add some
commentary to help others who may (as I did) find themselves chasing an
"Invalid Command" error after the device flags this condition.
This cleanup also eliminates a warning from "make W=1":
drivers/scsi/esp_scsi.c: In function 'esp_finish_select':
drivers/scsi/esp_scsi.c:1233:5: warning: variable 'orig_select_state' set but not used [-Wunused-but-set-variable]
u8 orig_select_state;
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When in MESSAGE IN phase, the ESP device does not automatically
acknowledge each byte that is transferred by PIO. The mac_esp driver
neglects to explicitly ack them, which causes a timeout during messages
larger than one byte (e.g. tag bytes during reconnect). Fix this with an
ESP_CMD_MOK command after each byte.
The MESSAGE IN phase is also different in that each byte transferred
raises ESP_INTR_FDONE. So don't exit the transfer loop for this interrupt,
for this phase.
That resolves the "Reconnect IRQ2 timeout" error on those Macs which use
PIO transfers instead of PDMA. This patch also improves on the weak tests
for unexpected interrupts and phase changes during PIO transfers.
Tested-by: Stan Johnson <userm57@yahoo.com>
Fixes: 02507a80b3 ("[PATCH] [SCSI] mac_esp: fix PIO mode, take 2")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avoid the following warning from "make C=1":
CHECK drivers/scsi/mac_esp.c
drivers/scsi/mac_esp.c:357:30: warning: incorrect type in initializer (different address spaces)
drivers/scsi/mac_esp.c:357:30: expected unsigned char [usertype] *fifo
drivers/scsi/mac_esp.c:357:30: got void [noderef] <asn:2>*
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add const to bin_attribute structures as they are only passed to the
functions system_{remove/create}_bin_file. The arguments passed are of
type const, so declare the structures to be const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If cxgbi_ep_connect() is called with valid shost then find associated
ndev and use ndev->ifindex to find route.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the lines above this test, 8 'kzalloc' are performed, but only 7
results are tested.
Add the missing one (i.e. '!ioc->port_enable_cmds.reply').
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Regenerate firmware files to make cleaner base for following fix.
This removes some unused definitions and reorders some #defines, but
the code remains the same.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, calls to nvmet_fc_rcv_fcp_req() always copied the
FC-NVME cmd iu to a temporary buffer before returning, allowing
the driver to immediately repost the buffer to the hardware.
To address timing conditions on queue element structures vs async
command reception, the nvmet_fc transport occasionally may need to
hold on to the command iu buffer for a short period. In these cases,
the nvmet_fc_rcv_fcp_req() will return a special return code
(-EOVERFLOW). In these cases, the LLDD must delay until the new
defer_rcv lldd callback is called before recycling the buffer back
to the hw.
This patch adds support for the new nvmet_fc transport defer_rcv
callback and recognition of the new error code when passing commands
to the transport.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Two small fixes, one re-fix of a previous fix and five patches sorting
out hotplug in the bnx2X class of drivers. The latter is rather
involved, but necessary because these drivers have started dropping
lockdep recursion warnings on the hotplug lock because of its
conversion to a percpu rwsem.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Lg/x
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two small fixes, one re-fix of a previous fix and five patches sorting
out hotplug in the bnx2X class of drivers. The latter is rather
involved, but necessary because these drivers have started dropping
lockdep recursion warnings on the hotplug lock because of its
conversion to a percpu rwsem"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sg: only check for dxfer_len greater than 256M
scsi: aacraid: reading out of bounds
scsi: qedf: Limit number of CQs
scsi: bnx2i: Simplify cpu hotplug code
scsi: bnx2fc: Simplify CPU hotplug code
scsi: bnx2i: Prevent recursive cpuhotplug locking
scsi: bnx2fc: Prevent recursive cpuhotplug locking
scsi: bnx2fc: Plug CPU hotplug race
If a SES device returns an error on a requested diagnostic page, we are
currently printing an error indicating the wrong page was received. Fix
this up to simply return a failure and only check the returned page when
the diagnostic page buffer was populated by the device.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If blk_queue_get() in st_probe fails, disk->queue must not be set to
SDp->request_queue, as that would result in put_disk() dropping a not
taken reference.
Thus, disk->queue should be set only after a successful blk_queue_get().
Fixes: 2b5bebccd2 ("st: Take additional queue ref in st_probe")
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Acked-by: Shirish Pargaonkar <spargaonkar@suse.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We need to override Kbuild rules for copying shipped files, otherwise
aic7xxx_reg.h and aic7xxx_reg_print.c will be ovewritten by old versions.
Fixes: 516b7db593
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ahc_platform_dump_card_state() does nothing. Remove it.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Scsi_cmnd is an unsuitable argument for eh_device_reset_handler(),
eh_target_reset_handler(), and eh_host_reset_handler() which do not have
the scope of one single SCSI command. These callbacks tend to use
fc_block_scsi_eh() requiring scsi_cmnd. In order to start decoupling
above eh callbacks from scsi_cmnd, introduce a new variant of the
function called fc_block_rport() taking an fc_rport as argument.
Refactor the old fc_block_scsi_eh() to simply delegate to
fc_block_rport().
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support to the driver to set the exchange threshold value for
the number of outstanding AENs.
Signed-off-by: Duane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: Darren Trapp <darren.trapp@cavium.com>
Signed-off-by: Anil Gurumurthy <anil.gurumurthy@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch does not change any functionality.
Following cleanups have been done as requested by reviewer
- Changed waitQ --> waitq
- Collapsed multiple debug statements into single
- Remove extra parentheses in if-else as per operator precedence
- Remove unnecessary casting
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Dick Kennedy