The variable 'res' is being initialized with a value that is never read and
it is being updated later with a new value. The initialization is redundant
and can be removed.
Link: https://lore.kernel.org/r/20200722154404.959267-1-colin.king@canonical.com
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Addresses-Coverity: ("Unused value")
libata currently attempts to reset even if the SATA disk is unplugged. To
avoid the meaningless reset of a missing disk, libsas should report offline
status to libata. libata already provides a .prereset callback for this
purpose. This is called by ata_eh_reset() and can be used to influence
whether a reset attempt should be made.
Add sas_ata_preset callback to check status of phy and disk. If the disk is
already offline or phy is disabled, we return -ENOENT to libata to avoid
the reset.
Link: https://lore.kernel.org/r/1595408643-63011-3-git-send-email-luojiaxing@huawei.com
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
sas_sata_ops uses ata_std_postreset as .postreset callback. However,
ata_std_postreset() calls sata_scr_read()/sata_scr_write() which need to
access the ATA SCR register. This register not available in the libsas case
and the functions always return -EOPNOTSUPP.
Drop the .postreset callback.
Link: https://lore.kernel.org/r/1595408643-63011-2-git-send-email-luojiaxing@huawei.com
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sparse reports a warning at sas_ata_qc_issue()
warning: context imbalance in sas_ata_qc_issue() - unexpected unlock
The root cause is the missing annotation at sas_ata_qc_issue()
Add the missing __must_hold(ap->lock) annotation
Link: https://lore.kernel.org/r/20200411001933.10072-7-jbi.octave@gmail.com
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is no reason to expose SATA_PMP config option when no SATA
host drivers are enabled. To fix it add SATA_HOST config option,
make all SATA host drivers select it and finally make SATA_PMP
config options depend on it.
This also serves as preparation for the future changes which
optimize libata core code size on PATA only setups.
CC: "James E.J. Bottomley" <jejb@linux.ibm.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> # for SCSI bits
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently we use a mixture of %016llx, %llx, and %16llx when printing a SAS
address.
Since the most significant nibble of the SAS address is always 5 - as per
standard - this formatting is not so important; but some fake SAS addresses
for SATA devices may not be. And we have mangled/invalid address to
consider also. And it's better to be consistent in the code, so use a fixed
format.
The SAS address is a fixed size at 64b, so we want to 0 byte extend to 16
nibbles, so use %016llx globally.
Also make some prints to be explicitly hex, and tidy some whitespace issue.
Link: https://lore.kernel.org/r/1576758957-227350-1-git-send-email-john.garry@huawei.com
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Mark switch cases where we are expecting to fall through.
Fix the following warning (Building: mtx1_defconfig mips):
drivers/scsi/libsas/sas_discover.c: In function ‘sas_discover_domain’:
./include/linux/printk.h:309:2: warning: this statement may fall through [-Wimplicit-fallthrough=]
printk(KERN_NOTICE pr_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/libsas/sas_discover.c:459:3: note: in expansion of macro ‘pr_notice’
pr_notice("ATA device seen but CONFIG_SCSI_SAS_ATA=N so cannot attach\n");
^~~~~~~~~
drivers/scsi/libsas/sas_discover.c:462:2: note: here
default:
^~~~~~~
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
This is the final round of mostly small fixes in our initial submit.
It's mostly minor fixes and driver updates. The only change of note
is adding a virt_boundary_mask to the SCSI host and host template to
parametrise this for NVMe devices instead of having them do a call in
slave_alloc. It's a fairly straightforward conversion except in the
two NVMe handling drivers that didn't set it who now have a virtual
infinity parameter added.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXTJS/yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishQTNAQCsTdkA
IN1BvDBbE+KO8mvL5DuRxLtnDU6Pq5K6fkrE3gD/a1GkqyPPaJIuspq7fQY87DH/
o7VsJd/5uGphIE2Ls+M=
=38XV
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is the final round of mostly small fixes in our initial submit.
It's mostly minor fixes and driver updates. The only change of note is
adding a virt_boundary_mask to the SCSI host and host template to
parametrise this for NVMe devices instead of having them do a call in
slave_alloc. It's a fairly straightforward conversion except in the
two NVMe handling drivers that didn't set it who now have a virtual
infinity parameter added"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits)
scsi: megaraid_sas: set an unlimited max_segment_size
scsi: mpt3sas: set an unlimited max_segment_size for SAS 3.0 HBAs
scsi: IB/srp: set virt_boundary_mask in the scsi host
scsi: IB/iser: set virt_boundary_mask in the scsi host
scsi: storvsc: set virt_boundary_mask in the scsi host template
scsi: ufshcd: set max_segment_size in the scsi host template
scsi: core: take the DMA max mapping size into account
scsi: core: add a host / host template field for the virt boundary
scsi: core: Fix race on creating sense cache
scsi: sd_zbc: Fix compilation warning
scsi: libfc: fix null pointer dereference on a null lport
scsi: zfcp: fix GCC compiler warning emitted with -Wmaybe-uninitialized
scsi: zfcp: fix request object use-after-free in send path causing wrong traces
scsi: zfcp: fix request object use-after-free in send path causing seqno errors
scsi: megaraid_sas: Update driver version to 07.710.50.00
scsi: megaraid_sas: Add module parameter for FW Async event logging
scsi: megaraid_sas: Enable msix_load_balance for Invader and later controllers
scsi: megaraid_sas: Fix calculation of target ID
scsi: lpfc: reduce stack size with CONFIG_GCC_PLUGIN_STRUCTLEAK_VERBOSE
scsi: devinfo: BLIST_TRY_VPD_PAGES for SanDisk Cruzer Blade
...
The function sas_wait_eh is declared static and marked EXPORT_SYMBOL, which
is at best an odd combination. Because the function is not used outside of
the drivers/scsi/libsas/sas_scsi_host.c file it is defined in, this commit
removes the EXPORT_SYMBOL() marking.
Signed-off-by: Denis Efremov <efremov@linux.com>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly update of the usual drivers: qla2xxx, hpsa, lpfc, ufs,
mpt3sas, ibmvscsi, megaraid_sas, bnx2fc and hisi_sas as well as the
removal of the osst driver (I heard from Willem privately that he
would like the driver removed because all his test hardware has
failed). Plus number of minor changes, spelling fixes and other
trivia.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXSTl4yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishdcxAQDCJVbd
fPUX76/V1ldupunF97+3DTharxxbst+VnkOnCwD8D4c0KFFFOI9+F36cnMGCPegE
fjy17dQLvsJ4GsidHy8=
=aS5B
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: qla2xxx, hpsa, lpfc, ufs,
mpt3sas, ibmvscsi, megaraid_sas, bnx2fc and hisi_sas as well as the
removal of the osst driver (I heard from Willem privately that he
would like the driver removed because all his test hardware has
failed). Plus number of minor changes, spelling fixes and other
trivia.
The big merge conflict this time around is the SPDX licence tags.
Following discussion on linux-next, we believe our version to be more
accurate than the one in the tree, so the resolution is to take our
version for all the SPDX conflicts"
Note on the SPDX license tag conversion conflicts: the SCSI tree had
done its own SPDX conversion, which in some cases conflicted with the
treewide ones done by Thomas & co.
In almost all cases, the conflicts were purely syntactic: the SCSI tree
used the old-style SPDX tags ("GPL-2.0" and "GPL-2.0+") while the
treewide conversion had used the new-style ones ("GPL-2.0-only" and
"GPL-2.0-or-later").
In these cases I picked the new-style one.
In a few cases, the SPDX conversion was actually different, though. As
explained by James above, and in more detail in a pre-pull-request
thread:
"The other problem is actually substantive: In the libsas code Luben
Tuikov originally specified gpl 2.0 only by dint of stating:
* This file is licensed under GPLv2.
In all the libsas files, but then muddied the water by quoting GPLv2
verbatim (which includes the or later than language). So for these
files Christoph did the conversion to v2 only SPDX tags and Thomas
converted to v2 or later tags"
So in those cases, where the spdx tag substantially mattered, I took the
SCSI tree conversion of it, but then also took the opportunity to turn
the old-style "GPL-2.0" into a new-style "GPL-2.0-only" tag.
Similarly, when there were whitespace differences or other differences
to the comments around the copyright notices, I took the version from
the SCSI tree as being the more specific conversion.
Finally, in the spdx conversions that had no conflicts (because the
treewide ones hadn't been done for those files), I just took the SCSI
tree version as-is, even if it was old-style. The old-style conversions
are perfectly valid, even if the "-only" and "-or-later" versions are
perhaps more descriptive.
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (185 commits)
scsi: qla2xxx: move IO flush to the front of NVME rport unregistration
scsi: qla2xxx: Fix NVME cmd and LS cmd timeout race condition
scsi: qla2xxx: on session delete, return nvme cmd
scsi: qla2xxx: Fix kernel crash after disconnecting NVMe devices
scsi: megaraid_sas: Update driver version to 07.710.06.00-rc1
scsi: megaraid_sas: Introduce various Aero performance modes
scsi: megaraid_sas: Use high IOPS queues based on IO workload
scsi: megaraid_sas: Set affinity for high IOPS reply queues
scsi: megaraid_sas: Enable coalescing for high IOPS queues
scsi: megaraid_sas: Add support for High IOPS queues
scsi: megaraid_sas: Add support for MPI toolbox commands
scsi: megaraid_sas: Offload Aero RAID5/6 division calculations to driver
scsi: megaraid_sas: RAID1 PCI bandwidth limit algorithm is applicable for only Ventura
scsi: megaraid_sas: megaraid_sas: Add check for count returned by HOST_DEVICE_LIST DCMD
scsi: megaraid_sas: Handle sequence JBOD map failure at driver level
scsi: megaraid_sas: Don't send FPIO to RL Bypass queue
scsi: megaraid_sas: In probe context, retry IOC INIT once if firmware is in fault
scsi: megaraid_sas: Release Mutex lock before OCR in case of DCMD timeout
scsi: megaraid_sas: Call disable_irq from process IRQ poll
scsi: megaraid_sas: Remove few debug counters from IO path
...
Many times in libsas, and in LLDDs which use libsas, the check for an
expander device is re-implemented or open coded.
Use dev_is_expander() instead. We rename this from
sas_dev_type_is_expander() to not spill so many lines in referencing.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since we are processing events synchronously now, the second call of
sas_ex_join_wide_port() in sas_ex_discover_dev() is not needed. There will
be no races with other works in disco workqueue. So remove the second
sas_ex_join_wide_port().
I did not change the return value of 'res' to error when discover failed
because we need to continue to discover other phys if one phy discover
failed. So let's keep that logic as before and just add a debug log to
detect the failure. And directly return if second fanout expander attatched
to the parent expander because it has nothing to do after the phy is
disabled.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 135 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531081036.435762997@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Six minor fixes to device drivers and one to the multipath alua
handler. The most extensive fix is the zfcp port remove prevention
one, but it's impact is only s390.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXPJlASYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishSElAP9A/qo+
mLomrWOPMGqkQKOX7Mp3sP5lMllbvPndrR+9KQD/eDzFp3HCyUO2OFd6aR7/X90H
IZ+cd/wJCSHenKMJOX8=
=NFnR
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Six minor fixes to device drivers and one to the multipath alua
handler.
The most extensive fix is the zfcp port remove prevention one, but
it's impact is only s390"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: libsas: delete sas port if expander discover failed
scsi: libsas: only clear phy->in_shutdown after shutdown event done
scsi: scsi_dh_alua: Fix possible null-ptr-deref
scsi: smartpqi: properly set both the DMA mask and the coherent DMA mask
scsi: zfcp: fix to prevent port_remove with pure auto scan LUNs (only sdevs)
scsi: zfcp: fix missing zfcp_port reference put on -EBUSY from port_remove
scsi: libcxgbi: add a check for NULL pointer in cxgbi_check_route()
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license this program
is distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 59 temple place suite 330 boston ma 02111
1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 83 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.021731668@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1334 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the event queue is full of phy up and down events and reached the
threshold, we will queue a shutdown-event, and set phy->in_shutdown so that
we will not queue a shutdown-event again. But before the shutdown-event can
be executed, every phy-down event will clear
phy->in_shutdown and a new shutdown-event will be queued. The queue will
be full of these shutdown-events.
Fix this by only clear phy->in_shutdown in sas_phye_shutdown(), that is
after the first shutdown-event has been executed.
Fixes: f12486e06a ("scsi: libsas: shut down the PHY if events reached the threshold")
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: John Garry <john.garry@huawei.com>
CC: Johannes Thumshirn <jthumshirn@suse.de>
CC: Ewan Milne <emilne@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Tomas Henzl <thenzl@redhat.com>
CC: Dan Williams <dan.j.williams@intel.com>
CC: Hannes Reinecke <hare@suse.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Based on 1 normalized pattern(s):
this file is licensed under gplv2 this program is free software you
can redistribute it and or modify it under the terms of the gnu
general public license as published by the free software foundation
either version 2 of the license or at your option any later version
this program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details you should have received a
copy of the gnu general public license along with this program if
not write to the free software foundation inc 59 temple place suite
330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 5 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520071858.561902672@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the the GPLv2 SPDX tag instead of verbose boilerplate text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the the GPLv2+ SPDX tag instead of verbose boilerplate text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
sas_task.c is the only libsas file missing licensing information. Add a
GPLv2 tag for the default kernel license.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have EXPORT_.*_SYMBOL_GPL inside which was used in the
initial scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we print expander PHY indexes in a mix of decimal and hex.
It is more consistent and also more convenient to read decimal, so
make this change.
We use width of 2 for expander and 1 for root PHYs prints.
Some lines which were needlessly spilling multiple lines are unified.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When we discover the PHY is empty in sas_rediscover_dev(), the PHY
information (like negotiated linkrate) is not updated.
As such, for a user examining sysfs for that PHY, they would see
incorrect values:
root@(none)$ cd /sys/class/sas_phy/phy-0:0:20
root@(none)$ more negotiated_linkrate
3.0 Gbit
root@(none)$ echo 0 > enable
root@(none)$ more negotiated_linkrate
3.0 Gbit
So fix this, simply discover the PHY again, even though we know it's empty;
in the above example, this gives us:
root@(none)$ more negotiated_linkrate
Phy disabled
We must do this after unregistering the device associated with the PHY
(in sas_unregister_devs_sas_addr()).
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
According to the SAS spec, an expander device shall transmit BROADCAST
(CHANGE) from at least one phy in each expander port other than the
expander port that is the cause for transmitting BROADCAST (CHANGE).
As such, for when the link is lost for a root PHY attached to an expander
PHY, we get no broadcast event.
This causes an issue for libsas, in that we will not revalidate the domain
for these events.
As a solution, for when a root PHY is formed or deformed from a root port,
insert a broadcast event to trigger a domain revalidation.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When an expander PHY which was part of a wideport disconnects, we would see
a log like this from sas_rediscover():
[ 39.695554] sas: phy20 part of wide port with phy16
Here, phy20 is the PHY that disconnected, and phy16 is the lowest indexed
member PHY of the wideport.
The log implies the phy20 is still part of the wideport with phy16, so is
misleading or, at least, vague.
Improve the logs in SAS rediscovery by removing this log and adding a log
in sas_rediscover_dev() to tell what's really going on.
While we're at it, also make the logs in sas_find_bcast_dev() more
informative (and more consistent with the reset of the expander logs).
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently for fixing the linkrate matching during discovery such that the
linkrate of a SATA PHY does not exceed min pathway to initiator, we set the
SATA PHY programmed min linkrate to the same value as the programmed max
linkrate.
This is unnecessary, and we should be able to keep the same programmed min
linkrate if it is already lower than this new max programmed linkrate.
This patch makes that change.
In effect, this will not make much difference since we generally will
negotiate a linkrate at the programmed max linkrate, and the programmed min
linkrate will have no impact.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Many times we use 8 for SAS address length, while we already have a macro
for this - SAS_ADDR_SIZE.
Replace instances of this with the macro. However, don't touch the SAS
address array sizes sas.h, as these are defined according to the SAS spec.
Some missing whitespaces are also added, and whitespace indentation
in sas_hash_addr() is also fixed (see sas_hash_addr()).
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc,
hisi_sas, target/iscsi and target/core. Additionally Christoph
refactored gdth as part of the dma changes. The major mid-layer
change this time is the removal of bidi commands and with them the
whole of the osd/exofs driver and filesystem.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXIC54SYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishT1GAPwJEV23
ExPiPsnuVgKj49nLTagZ3rILRQcYNbL+MNYqxQEA0cT8FHzSDBfWY5OKPNE+RQ8z
f69LpXGmMpuagKGvvd4=
=Fhy1
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc,
hisi_sas, target/iscsi and target/core.
Additionally Christoph refactored gdth as part of the dma changes. The
major mid-layer change this time is the removal of bidi commands and
with them the whole of the osd/exofs driver and filesystem. This is a
major simplification for block and mq in particular"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (240 commits)
scsi: cxgb4i: validate tcp sequence number only if chip version <= T5
scsi: cxgb4i: get pf number from lldi->pf
scsi: core: replace GFP_ATOMIC with GFP_KERNEL in scsi_scan.c
scsi: mpt3sas: Add missing breaks in switch statements
scsi: aacraid: Fix missing break in switch statement
scsi: kill command serial number
scsi: csiostor: drop serial_number usage
scsi: mvumi: use request tag instead of serial_number
scsi: dpt_i2o: remove serial number usage
scsi: st: osst: Remove negative constant left-shifts
scsi: ufs-bsg: Allow reading descriptors
scsi: ufs: Allow reading descriptor via raw upiu
scsi: ufs-bsg: Change the calling convention for write descriptor
scsi: ufs: Remove unused device quirks
Revert "scsi: ufs: disable vccq if it's not needed by UFS device"
scsi: megaraid_sas: Remove a bunch of set but not used variables
scsi: clean obsolete return values of eh_timed_out
scsi: sd: Optimal I/O size should be a multiple of physical block size
scsi: MAINTAINERS: SCSI initiator and target tweaks
scsi: fcoe: make use of fip_mode enum complete
...
Clang warns several times in the scsi subsystem (trimmed for brevity):
drivers/scsi/hpsa.c:6209:7: warning: overflow converting case value to
switch condition type (2147762695 to 18446744071562347015) [-Wswitch]
case CCISS_GETBUSTYPES:
^
drivers/scsi/hpsa.c:6208:7: warning: overflow converting case value to
switch condition type (2147762694 to 18446744071562347014) [-Wswitch]
case CCISS_GETHEARTBEAT:
^
The root cause is that the _IOC macro can generate really large numbers,
which don't fit into type 'int', which is used for the cmd parameter in
the ioctls in scsi_host_template. My research into how GCC and Clang are
handling this at a low level didn't prove fruitful. However, looking at
the rest of the kernel tree, all ioctls use an 'unsigned int' for the
cmd parameter, which will fit all of the _IOC values in the scsi/ata
subsystems.
Make that change because none of the ioctls expect a negative value for
any command, it brings the ioctls inline with the reset of the kernel,
and it removes ambiguity, which is never good when dealing with compilers.
Link: https://github.com/ClangBuiltLinux/linux/issues/85
Link: https://github.com/ClangBuiltLinux/linux/issues/154
Link: https://github.com/ClangBuiltLinux/linux/issues/157
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Bradley Grove <bgrove@attotech.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since the function scsi_to_u32() is identical to get_unaligned_be32(),
change all scsi_to_u32() calls into get_unaligned_be32() calls.
Cc: Jian Luo <luojian5@huawei.com>
Cc: John Garry <john.garry@huawei.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
+----------+ +----------+
| | | |
| |--- 3.0 G ---| |--- 6.0 G --- SAS disk
| | | |
| |--- 3.0 G ---| |--- 6.0 G --- SAS disk
|initiator | | |
| device |--- 3.0 G ---| Expander |--- 6.0 G --- SAS disk
| | | |
| |--- 3.0 G ---| |--- 6.0 G --- SATA disk -->failed to connect
| | | |
| | | |--- 6.0 G --- SATA disk -->failed to connect
| | | |
+----------+ +----------+
According to Serial Attached SCSI - 1.1 (SAS-1.1):
If an expander PHY attached to a SATA PHY is using a physical link rate
greater than the maximum connection rate supported by the pathway from an
STP initiator port, a management application client should use the SMP PHY
CONTROL function (see 10.4.3.10) to set the PROGRAMMED MAXIMUM PHYSICAL
LINK RATE field of the expander PHY to the maximum connection rate
supported by the pathway from that STP initiator port.
Currently libsas does not support checking if this condition occurs, nor
rectifying when it does.
Such a condition is not at all common, however it has been seen on some
pre-silicon environments where the initiator PHY only supports a 1.5 Gbit
maximum linkrate, mated with 12G expander PHYs and 3/6G SATA phy.
This patch adds support for checking and rectifying this condition during
initial device discovery only.
We do support checking min pathway connection rate during revalidation phase,
when new devices can be detected in the topology. However we do not
support in the case of the the user reprogramming PHY linkrates, such that
min pathway condition is not met/maintained.
A note on root port PHY rates:
The libsas root port PHY rates calculation is broken. Libsas sets the
rates (min, max, and current linkrate) of a root port to the same linkrate
of the first PHY member of that same port. In doing so, it assumes that
all other PHYs which subsequently join the port to have the same
negotiated linkrate, when they could actually be different.
In practice this doesn't happen, as initiator and expander PHYs are
normally initialised with consistent min/max linkrates.
This has not caused an issue so far, so leave alone for now.
Tested-by: Jian Luo <luojian5@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the SMP PHY control execution result is checked, however the
function result for the command is not.
As such, we may be missing all potential errors, like SMP FUNCTION FAILED,
INVALID REQUEST FRAME LENGTH, etc., meaning the PHY control request has
failed.
In some scenarios we need to ensure the function result is accepted, so add
a check for this.
Tested-by: Jian Luo <luojian5@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly update of the usual drivers: smarpqi, lpfc, qedi,
megaraid_sas, libsas, zfcp, mpt3sas, hisi_sas. Additionally, we have
a pile of annotation, unused variable and minor updates. The big API
change is the updates for Christoph's DMA rework which include
removing the DISABLE_CLUSTERING flag. And finally there are a couple
of target tree updates.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXCEUNiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishdjKAP9vrTTv
qFaYmAoRSbPq9ZiixaXLMy0K/6o76Uay0gnBqgD/fgn3jg/KQ6alNaCjmfeV3wAj
u1j3H7tha9j1it+4pUw=
=GDa+
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: smarpqi, lpfc, qedi,
megaraid_sas, libsas, zfcp, mpt3sas, hisi_sas.
Additionally, we have a pile of annotation, unused variable and minor
updates.
The big API change is the updates for Christoph's DMA rework which
include removing the DISABLE_CLUSTERING flag.
And finally there are a couple of target tree updates"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (259 commits)
scsi: isci: request: mark expected switch fall-through
scsi: isci: remote_node_context: mark expected switch fall-throughs
scsi: isci: remote_device: Mark expected switch fall-throughs
scsi: isci: phy: Mark expected switch fall-through
scsi: iscsi: Capture iscsi debug messages using tracepoints
scsi: myrb: Mark expected switch fall-throughs
scsi: megaraid: fix out-of-bound array accesses
scsi: mpt3sas: mpt3sas_scsih: Mark expected switch fall-through
scsi: fcoe: remove set but not used variable 'port'
scsi: smartpqi: call pqi_free_interrupts() in pqi_shutdown()
scsi: smartpqi: fix build warnings
scsi: smartpqi: update driver version
scsi: smartpqi: add ofa support
scsi: smartpqi: increase fw status register read timeout
scsi: smartpqi: bump driver version
scsi: smartpqi: add smp_utils support
scsi: smartpqi: correct lun reset issues
scsi: smartpqi: correct volume status
scsi: smartpqi: do not offline disks for transient did no connect conditions
scsi: smartpqi: allow for larger raid maps
...
Not all host drivers are PCI drivers - like hisi_sas, which supports a
platform driver - so remove reference to "pcidev".
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Like sas_printk() did previously, SAS_DPRINTK() offers little value now
that libsas logs already have the "sas" prefix through pr_fmt(fmt). So it
can be dropped.
However, after reviewing some logs in libsas, it is noticed that debug
level is too low in many instances.
So this change drops SAS_DPRINTK() and revises some logs to a more
appropriate level. However many stay at debug level, although some
are significantly promoted.
We add -DDEBUG for compilation so that we keep the debug messages by
default, as before.
All the pre-existing checkpatch errors for spanning messages across
multiple lines are also fixed.
Finally, all other references to printk() [apart from special formatting
in sas_ata.c] are removed and replaced with appropriate pr_xxx().
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The printk wrapper sas_printk() adds little value now that libsas logs
already have the "sas" prefix through pr_fmt(fmt), so just use pr_notice()
directly.
In addition, strings which span multiple lines are reunited.
Originally-from: Joe Perches <joe@perches.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation for dropping the libsas printk wrappers, use pr_fmt(fmt)
declaration to add the framework log prefix - "sas".
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The code in these files is not longer referenced, so delete them.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is nothing it could synchronize against, so don't go through
the pains of acquiring the lock.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When the lldd is processing the complete sas task in interrupt and set the
task stat as SAS_TASK_STATE_DONE, the smp timeout timer is able to be
triggered at the same time. And smp_task_timedout() will complete the task
wheter the SAS_TASK_STATE_DONE is set or not. Then the sas task may freed
before lldd end the interrupt process. Thus a use-after-free will happen.
Fix this by calling the complete() only when SAS_TASK_STATE_DONE is not
set. And remove the check of the return value of the del_timer(). Once the
LLDD sets DONE, it must call task->done(), which will call
smp_task_done()->complete() and the task will be completed and freed
correctly.
Reported-by: chenxiang <chenxiang66@hisilicon.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: John Garry <john.garry@huawei.com>
CC: Johannes Thumshirn <jthumshirn@suse.de>
CC: Ewan Milne <emilne@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Tomas Henzl <thenzl@redhat.com>
CC: Dan Williams <dan.j.williams@intel.com>
CC: Hannes Reinecke <hare@suse.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When ata device IDENTIFY failed, the ata device status is ATA_DEV_UNKNOWN. The
libata reported like:
[113518.620433] ata5.00: qc timeout (cmd 0xec)
[113518.653646] ata5.00: failed to IDENTIFY (I/O error, err_mask=0x4)
But libsas verifies the device status by ata_dev_disabled(), which skipped
ATA_DEV_UNKNOWN. This will make libsas think the ata device probing succeed
the device cannot be actually brought up. And even the new bcast of this
device will be considered as flutter and will not probe this device again.
Change ata_dev_disabled() to !ata_dev_enabled() so that libsas can deal with
this if the ata device probe failed. New bcasts can let us try to probe the
device again and bring it up if it is fine to IDENTIFY.
Tested-by: Zhou Yupeng <zhouyupeng1@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: John Garry <john.garry@huawei.com>
CC: Johannes Thumshirn <jthumshirn@suse.de>
CC: Ewan Milne <emilne@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Tomas Henzl <thenzl@redhat.com>
CC: Dan Williams <dan.j.williams@intel.com>
CC: Hannes Reinecke <hare@suse.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If we went into sas_rediscover_dev() the attached_sas_addr was already insured
not to be zero. So it's unnecessary to check if the attached_sas_addr is zero.
And although if the sas address is not changed, we always have to unregister
the old device when we are going to register a new one. We cannot just leave
the device there and bring up the new.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: chenxiang <chenxiang66@hisilicon.com>
CC: John Garry <john.garry@huawei.com>
CC: Johannes Thumshirn <jthumshirn@suse.de>
CC: Ewan Milne <emilne@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Tomas Henzl <thenzl@redhat.com>
CC: Dan Williams <dan.j.williams@intel.com>
CC: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now LLDDs have to implement lldd_port_deformed method otherwise NULL
dereference will happen. Make it optional and remove the dummy implementation
in hisi_sas.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: John Garry <john.garry@huawei.com>
CC: Johannes Thumshirn <jthumshirn@suse.de>
CC: Ewan Milne <emilne@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Tomas Henzl <thenzl@redhat.com>
CC: Dan Williams <dan.j.williams@intel.com>
CC: Hannes Reinecke <hare@suse.com>
Acked-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No functional change.
Just introduce scsi_host_busy() and replace the direct read of
scsi_host->host_busy with this new API.
Cc: Omar Sandoval <osandov@fb.com>,
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>,
Cc: James Bottomley <james.bottomley@hansenpartnership.com>,
Cc: Christoph Hellwig <hch@lst.de>,
Cc: Don Brace <don.brace@microsemi.com>
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Laurence Oberman <loberman@redhat.com>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 2623c7a5f2 ("libata: add refcounting to ata_host") v4.17+ introduced
refcounting to ata_host and will increase or decrease the refcount when
adding or deleting transport ATA port.
Now the ata host for libsas is embedded in domain_device, and the ->kref
member is not initialized. Afer we add ata transport class, ata_host_get()
will be called when adding transport ATA port and a warning will be
triggered as below:
refcount_t: increment on 0; use-after-free.
WARNING: CPU: 2 PID: 103 at
lib/refcount.c:153 refcount_inc+0x40/0x48 ...... Call trace:
refcount_inc+0x40/0x48
ata_host_get+0x10/0x18
ata_tport_add+0x40/0x120
ata_sas_tport_add+0xc/0x14
sas_ata_init+0x7c/0xc8
sas_discover_domain+0x380/0x53c
process_one_work+0x12c/0x288
worker_thread+0x58/0x3f0
kthread+0xfc/0x128
ret_from_fork+0x10/0x18
And also when removing transport ATA port ata_host_put() will be called and
another similar warning will be triggered. If the refcount decreased to
zero, the ata host will be freed. But this ata host is only part of
domain_device, it cannot be freed directly.
So we have to change this embedded static ata host to a dynamically
allocated ata host and initialize the ->kref member. To use ata_host_get()
and ata_host_put() in libsas, we need to move the declaration of these
functions to the public libata.h and export them.
Fixes: b6240a4df0 ("scsi: libsas: add transport class for ATA devices")
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: John Garry <john.garry@huawei.com>
CC: Taras Kondratiuk <takondra@cisco.com>
CC: Tejun Heo <tj@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since commit 312d3e5611 ("[SCSI] libsas: remove ata_port.lock management
duties from lldds") the sas_ata_qc_issue() function unlocks the
ata_port.lock and disables interrupts before doing so. That lock is always
taken with disabled interrupts so at this point, the interrupts are already
disabled. There is no need to disable the interrupts before the unlock
operation because they are already disabled. Restoring the interrupt state
later does not change anything because they were disabled and remain
disabled. Therefore remove the operations which do not change the
behaviour.
Fixes: 312d3e5611 ("[SCSI] libsas: remove ata_port.lock management duties from lldds")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Colin Ian King