Simply letting IGROUPR be writable from userspace would break
migration from old kernels to newer kernels, because old kernels
incorrectly report interrupt groups as group 1. This would not be a big
problem if userspace wrote GICD_IIDR as read from the kernel, because we
could detect the incompatibility and return an error to userspace.
Unfortunately, this is not the case with current userspace
implementations and simply letting IGROUPR be writable from userspace for
an emulated GICv2 silently breaks migration and causes the destination
VM to no longer run after migration.
We now encourage userspace to write the read and expected value of
GICD_IIDR as the first part of a GIC register restore, and if we observe
a write to GICD_IIDR we know that userspace has been updated and has had
a chance to cope with older kernels (VGICv2 IIDR.Revision == 0)
incorrectly reporting interrupts as group 1, and therefore we now allow
groups to be user writable.
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In preparation for proper group 0 and group 1 support in the vgic, we
add a field in the struct irq to store the group of all interrupts.
We initialize the group to group 0 when emulating GICv2 and to group 1
when emulating GICv3, just like we treat them today. LPIs are always
group 1. We also continue to ignore writes from the guest, preserving
existing functionality, for now.
Finally, we also add this field to the vgic debug logic to show the
group for all interrupts.
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As we are about to tweak implementation aspects of the VGIC emulation,
while still preserving some level of backwards compatibility support,
add a field to keep track of the implementation revision field which is
reported to the VM and to userspace.
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Let's raise the number of supported vcpus along with
vgic v3 now that HW is looming with more physical CPUs.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
kvm_vgic_vcpu_early_init gets called after kvm_vgic_cpu_init which
is confusing. The call path is as follows:
kvm_vm_ioctl_create_vcpu
|_ kvm_arch_cpu_create
|_ kvm_vcpu_init
|_ kvm_arch_vcpu_init
|_ kvm_vgic_vcpu_init
|_ kvm_arch_vcpu_postcreate
|_ kvm_vgic_vcpu_early_init
Static initialization currently done in kvm_vgic_vcpu_early_init()
can be moved to kvm_vgic_vcpu_init(). So let's move the code and
remove kvm_vgic_vcpu_early_init(). kvm_arch_vcpu_postcreate() does
nothing.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
At the moment KVM supports a single rdist region. We want to
support several separate rdist regions so let's introduce a list
of them. This patch currently only cares about a single
entry in this list as the functionality to register several redist
regions is not yet there. So this only translates the existing code
into something functionally similar using that new data struct.
The redistributor region handle is stored in the vgic_cpu structure
to allow later computation of the TYPER last bit.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Now that we make sure we don't inject multiple instances of the
same GICv2 SGI at the same time, we've made another bug more
obvious:
If we exit with an active SGI, we completely lose track of which
vcpu it came from. On the next entry, we restore it with 0 as a
source, and if that wasn't the right one, too bad. While this
doesn't seem to trouble GIC-400, the architectural model gets
offended and doesn't deactivate the interrupt on EOI.
Another connected issue is that we will happilly make pending
an interrupt from another vcpu, overriding the above zero with
something that is just as inconsistent. Don't do that.
The final issue is that we signal a maintenance interrupt when
no pending interrupts are present in the LR. Assuming we've fixed
the two issues above, we end-up in a situation where we keep
exiting as soon as we've reached the active state, and not be
able to inject the following pending.
The fix comes in 3 parts:
- GICv2 SGIs have their source vcpu saved if they are active on
exit, and restored on entry
- Multi-SGIs cannot go via the Pending+Active state, as this would
corrupt the source field
- Multi-SGIs are converted to using MI on EOI instead of NPIE
Fixes: 16ca6a607d ("KVM: arm/arm64: vgic: Don't populate multiple LRs with the same vintid")
Reported-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
- Peace of mind locking fix in vgic_mmio_read_pending
- Allow hw-mapped interrupts to be reset when the VM resets
- Fix GICv2 multi-source SGI injection
- Fix MMIO synchronization for GICv2 on v3 emulation
- Remove excess verbosity on the console
-----BEGIN PGP SIGNATURE-----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=iyYE
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-fixes-for-v4.16-2' into HEAD
Resolve conflicts with current mainline
As we're about to change the way we map devices at HYP, we need
to move away from kern_hyp_va on an IO address.
One way of achieving this is to store the VAs in kvm_vgic_global_state,
and use that directly from the HYP code. This requires a small change
to create_hyp_io_mappings so that it can also return a HYP VA.
We take this opportunity to nuke the vctrl_base field in the emulated
distributor, as it is not used anymore.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
There is really no need to store the vgic_elrsr on the VGIC data
structures as the only need we have for the elrsr is to figure out if an
LR is inactive when we save the VGIC state upon returning from the
guest. We can might as well store this in a temporary local variable.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We currently don't allow resetting mapped IRQs from userspace, because
their state is controlled by the hardware. But we do need to reset the
state when the VM is reset, so we provide a function for the 'owner' of
the mapped interrupt to reset the interrupt state.
Currently only the timer uses mapped interrupts, so we call this
function from the timer reset logic.
Cc: stable@vger.kernel.org
Fixes: 4c60e360d6 ("KVM: arm/arm64: Provide a get_input_level for the arch timer")
Signed-off-by: Christoffer Dall <cdall@kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The GIC sometimes need to sample the physical line of a mapped
interrupt. As we know this to be notoriously slow, provide a callback
function for devices (such as the timer) which can do this much faster
than talking to the distributor, for example by comparing a few
in-memory values. Fall back to the good old method of poking the
physical GIC if no callback is provided.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
The doorbell interrupt is only useful if the vcpu is blocked on WFI.
In all other cases, recieving a doorbell interrupt is just a waste
of cycles.
So let's only enable the doorbell if a vcpu is getting blocked,
and disable it when it is unblocked. This is very similar to
what we're doing for the background timer.
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Let's use the irq bypass mechanism also used for x86 posted interrupts
to intercept the virtual PCIe endpoint configuration and establish our
LPI->VLPI mapping.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
In order to control the GICv4 view of virtual CPUs, we rely
on an irqdomain allocated for that purpose. Let's add a couple
of helpers to that effect.
At the same time, the vgic data structures gain new fields to
track all this... erm... wonderful stuff.
The way we hook into the vgic init is slightly convoluted. We
need the vgic to be initialized (in order to guarantee that
the number of vcpus is now fixed), and we must have a vITS
(otherwise this is all very pointless). So we end-up calling
the init from both vgic_init and vgic_its_create.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Add a new has_gicv4 field in the global VGIC state that indicates
whether the HW is GICv4 capable, as a per-VM predicate indicating
if there is a possibility for a VM to support direct injection
(the above being true and the VM having an ITS).
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
We want to reuse the core of the map/unmap functions for IRQ
forwarding. Let's move the computation of the hwirq in
kvm_vgic_map_phys_irq and pass the linux IRQ as parameter.
the host_irq is added to struct vgic_irq.
We introduce kvm_vgic_map/unmap_irq which take a struct vgic_irq
handle as a parameter.
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
In order to start handling guest access to GICv3 system registers,
let's add a hook that will get called when we trap a system register
access. This is gated by a new static key (vgic_v3_cpuif_trap).
Tested-by: Alexander Graf <agraf@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
The PMU IRQ number is set through the VCPU device's KVM_SET_DEVICE_ATTR
ioctl handler for the KVM_ARM_VCPU_PMU_V3_IRQ attribute, but there is no
enforced or stated requirement that this must happen after initializing
the VGIC. As a result, calling vgic_valid_spi() which relies on the
nr_spis being set during the VGIC init can incorrectly fail.
Introduce irq_is_spi, which determines if an IRQ number is within the
SPI range without verifying it against the actual VGIC properties.
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
When injecting an IRQ to the VGIC, you now have to present an owner
token for that IRQ line to show that you are the owner of that line.
IRQ lines driven from userspace or via an irqfd do not have an owner and
will simply pass a NULL pointer.
Also get rid of the unused kvm_vgic_inject_mapped_irq prototype.
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Having multiple devices being able to signal the same interrupt line is
very confusing and almost certainly guarantees a configuration error.
Therefore, introduce a very simple allocator which allows a device to
claim an interrupt line from the vgic for a given VM.
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
We are about to need this define in the arch timer code as well so move
it to a common location.
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
If userspace creates the VCPUs after initializing the VGIC, then we end
up in a situation where we trigger a bug in kvm_vcpu_get_idx(), because
it is called prior to adding the VCPU into the vcpus array on the VM.
There is no tight coupling between the VCPU index and the area of the
redistributor region used for the VCPU, so we can simply ensure that all
creations of redistributors are serialized per VM, and increment an
offset when we successfully add a redistributor.
The vgic_register_redist_iodev() function can be called from two paths:
vgic_redister_all_redist_iodev() which is called via the kvm_vgic_addr()
device attribute handler. This patch already holds the kvm->lock mutex.
The other path is via kvm_vgic_vcpu_init, which is called through a
longer chain from kvm_vm_ioctl_create_vcpu(), which releases the
kvm->lock mutex just before calling kvm_arch_vcpu_create(), so we can
simply take this mutex again later for our purposes.
Fixes: ab6f468c10 ("KVM: arm/arm64: Register iodevs when setting redist base and creating VCPUs")
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Tested-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Changes include:
- A fix related to the 32-bit idmap stub
- A fix to the bitmask used to deode the operands of an AArch32 CP
instruction
- We have moved the files shared between arch/arm/kvm and
arch/arm64/kvm to virt/kvm/arm
- We add support for saving/restoring the virtual ITS state to
userspace
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZEZihAAoJEEtpOizt6ddyGDYH/jmGjDMnryORn2P2o10dUQKJ
RnHTQYnpOYqnprlkFtZFpmK+mjl/a8R1Btb7GK2EwmovTR95pMYPRqtrCTOL0aQA
4OToh7+vFGatwxsGCS6utazdhmx0UT/LhO/GEF4G1zOb7eVa4ZtS1NKLP2WjPD1E
RU3Qn8wa0pESv3tJScv8qo2+PWVX4krbFllhY2Hk0AkVQcI66ExkdVq4ikm1eUXn
rxzIayLG2bv3KEPNCzozdwoY9tDL+b40q6vN/RHGJmM05SZbbSx2/Bkw2RbslSpD
2hvhHWX7xeuEBcd5mZO7sP4WS3hM/BI8eX7q+uMeNJ9B+nM82yjGfOTtglVi2cc=
=JfvQ
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-v4.12-round2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
Second round of KVM/ARM Changes for v4.12.
Changes include:
- A fix related to the 32-bit idmap stub
- A fix to the bitmask used to deode the operands of an AArch32 CP
instruction
- We have moved the files shared between arch/arm/kvm and
arch/arm64/kvm to virt/kvm/arm
- We add support for saving/restoring the virtual ITS state to
userspace
The its->initialized doesn't bring much to the table, and creates
unnecessary ordering between setting the address and initializing it
(which amounts to exactly nothing).
Let's kill it altogether, making KVM_DEV_ARM_VGIC_CTRL_INIT the no-op
it deserves to be.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Instead of waiting with registering KVM iodevs until the first VCPU is
run, we can actually create the iodevs when the redist base address is
set. The only downside is that we must now also check if we need to do
this for VCPUs which are created after creating the VGIC, because there
is no enforced ordering between creating the VGIC (and setting its base
addresses) and creating the VCPUs.
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
support; virtual interrupt controller performance improvements; support
for userspace virtual interrupt controller (slower, but necessary for
KVM on the weird Broadcom SoCs used by the Raspberry Pi 3)
* MIPS: basic support for hardware virtualization (ImgTec
P5600/P6600/I6400 and Cavium Octeon III)
* PPC: in-kernel acceleration for VFIO
* s390: support for guests without storage keys; adapter interruption
suppression
* x86: usual range of nVMX improvements, notably nested EPT support for
accessed and dirty bits; emulation of CPL3 CPUID faulting
* generic: first part of VCPU thread request API; kvm_stat improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJZEHUkAAoJEL/70l94x66DBeYH/09wrpJ2FjU4Rqv7FxmqgWfH
9WGi4wvn/Z+XzQSyfMJiu2SfZVzU69/Y67OMHudy7vBT6knB+ziM7Ntoiu/hUfbG
0g5KsDX79FW15HuvuuGh9kSjUsj7qsQdyPZwP4FW/6ZoDArV9mibSvdjSmiUSMV/
2wxaoLzjoShdOuCe9EABaPhKK0XCrOYkygT6Paz1pItDxaSn8iW3ulaCuWMprUfG
Niq+dFemK464E4yn6HVD88xg5j2eUM6bfuXB3qR3eTR76mHLgtwejBzZdDjLG9fk
32PNYKhJNomBxHVqtksJ9/7cSR6iNPs7neQ1XHemKWTuYqwYQMlPj1NDy0aslQU=
=IsiZ
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"ARM:
- HYP mode stub supports kexec/kdump on 32-bit
- improved PMU support
- virtual interrupt controller performance improvements
- support for userspace virtual interrupt controller (slower, but
necessary for KVM on the weird Broadcom SoCs used by the Raspberry
Pi 3)
MIPS:
- basic support for hardware virtualization (ImgTec P5600/P6600/I6400
and Cavium Octeon III)
PPC:
- in-kernel acceleration for VFIO
s390:
- support for guests without storage keys
- adapter interruption suppression
x86:
- usual range of nVMX improvements, notably nested EPT support for
accessed and dirty bits
- emulation of CPL3 CPUID faulting
generic:
- first part of VCPU thread request API
- kvm_stat improvements"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (227 commits)
kvm: nVMX: Don't validate disabled secondary controls
KVM: put back #ifndef CONFIG_S390 around kvm_vcpu_kick
Revert "KVM: Support vCPU-based gfn->hva cache"
tools/kvm: fix top level makefile
KVM: x86: don't hold kvm->lock in KVM_SET_GSI_ROUTING
KVM: Documentation: remove VM mmap documentation
kvm: nVMX: Remove superfluous VMX instruction fault checks
KVM: x86: fix emulation of RSM and IRET instructions
KVM: mark requests that need synchronization
KVM: return if kvm_vcpu_wake_up() did wake up the VCPU
KVM: add explicit barrier to kvm_vcpu_kick
KVM: perform a wake_up in kvm_make_all_cpus_request
KVM: mark requests that do not need a wakeup
KVM: remove #ifndef CONFIG_S390 around kvm_vcpu_wake_up
KVM: x86: always use kvm_make_request instead of set_bit
KVM: add kvm_{test,clear}_request to replace {test,clear}_bit
s390: kvm: Cpu model support for msa6, msa7 and msa8
KVM: x86: remove irq disablement around KVM_SET_CLOCK/KVM_GET_CLOCK
kvm: better MWAIT emulation for guests
KVM: x86: virtualize cpuid faulting
...
We plan to support different migration ABIs, ie. characterizing
the ITS table layout format in guest RAM. For example, a new ABI
will be needed if vLPIs get supported for nested use case.
So let's introduce an array of supported ABIs (at the moment a single
ABI is supported though). The following characteristics are foreseen
to vary with the ABI: size of table entries, save/restore operation,
the way abi settings are applied.
By default the MAX_ABI_REV is applied on its creation. In subsequent
patches we will introduce a way for the userspace to change the ABI
in use.
The entry sizes now are set according to the ABI version and not
hardcoded anymore.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
We don't use these fields anymore so let's nuke them completely.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
There is no need to calculate and maintain live_lrs when we always
populate the lowest numbered LRs first on every entry and clear all LRs
on every exit.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
We don't have to save/restore the VMCR on every entry to/from the guest,
since on GICv2 we can access the control interface from EL1 and on VHE
systems with GICv3 we can access the control interface from KVM running
in EL2.
GICv3 systems without VHE becomes the rare case, which has to
save/restore the register on each round trip.
Note that userspace accesses may see out-of-date values if the VCPU is
running while accessing the VGIC state via the KVM device API, but this
is already the case and it is up to userspace to quiesce the CPUs before
reading the CPU registers from the GIC for an up-to-date view.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@cs.columbia.edu>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
We currently have some code to clear the list registers on GICv3, but we
never call this code, because the caller got nuked when removing the old
vgic. We also used to have a similar GICv2 part, but that got lost in
the process too.
Let's reintroduce the logic for GICv2 and call the logic when we
initialize the use of hypervisors on the CPU, for example when first
loading KVM or when exiting a low power state.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
VGICv3 CPU interface registers are accessed using
KVM_DEV_ARM_VGIC_CPU_SYSREGS ioctl. These registers are accessed
as 64-bit. The cpu MPIDR value is passed along with register id.
It is used to identify the cpu for registers access.
The VM that supports SEIs expect it on destination machine to handle
guest aborts and hence checked for ICC_CTLR_EL1.SEIS compatibility.
Similarly, VM that supports Affinity Level 3 that is required for AArch64
mode, is required to be supported on destination machine. Hence checked
for ICC_CTLR_EL1.A3V compatibility.
The arch/arm64/kvm/vgic-sys-reg-v3.c handles read and write of VGIC
CPU registers for AArch64.
For AArch32 mode, arch/arm/kvm/vgic-v3-coproc.c file is created but
APIs are not implemented.
Updated arch/arm/include/uapi/asm/kvm.h with new definitions
required to compile for AArch32.
The version of VGIC v3 specification is defined here
Documentation/virtual/kvm/devices/arm-vgic-v3.txt
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add a file to debugfs to read the in-kernel state of the vgic. We don't
do any locking of the entire VGIC state while traversing all the IRQs,
so if the VM is running the user/developer may not see a quiesced state,
but should take care to pause the VM using facilities in user space for
that purpose.
We also don't support LPIs yet, but they can be added easily if needed.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
One of the goals behind the VGIC redesign was to get rid of cached or
intermediate state in the data structures, but we decided to allow
ourselves to precompute the pending value of an IRQ based on the line
level and pending latch state. However, this has now become difficult
to base proper GICv3 save/restore on, because there is a potential to
modify the pending state without knowing if an interrupt is edge or
level configured.
See the following post and related message for more background:
https://lists.cs.columbia.edu/pipermail/kvmarm/2017-January/023195.html
This commit gets rid of the precomputed pending field in favor of a
function that calculates the value when needed, irq_is_pending().
The soft_pending field is renamed to pending_latch to represent that
this latch is the equivalent hardware latch which gets manipulated by
the input signal for edge-triggered interrupts and when writing to the
SPENDR/CPENDR registers.
After this commit save/restore code should be able to simply restore the
pending_latch state, line_level state, and config state in any order and
get the desired result.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
This patch allows to build and use vgic-v3 in 32-bit mode.
Unfortunately, it can not be split in several steps without extra
stubs to keep patches independent and bisectable. For instance,
virt/kvm/arm/vgic/vgic-v3.c uses function from vgic-v3-sr.c, handling
access to GICv3 cpu interface from the guest requires vgic_v3.vgic_sre
to be already defined.
It is how support has been done:
* handle SGI requests from the guest
* report configured SRE on access to GICv3 cpu interface from the guest
* required vgic-v3 macros are provided via uapi.h
* static keys are used to select GIC backend
* to make vgic-v3 build KVM_ARM_VGIC_V3 guard is removed along with
the static inlines
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Currently GIC backend is selected via alternative framework and this
is fine. We are going to introduce vgic-v3 to 32-bit world and there
we don't have patching framework in hand, so we can either check
support for GICv3 every time we need to choose which backend to use or
try to optimise it by using static keys. The later looks quite
promising because we can share logic involved in selecting GIC backend
between architectures if both uses static keys.
This patch moves arm64 from alternative to static keys framework for
selecting GIC backend. For that we embed static key into vgic_global
and enable the key during vgic initialisation based on what has
already been exposed by the host GIC driver.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Now that we have the necessary infrastructure to handle MMIO accesses
in HYP, perform the GICV access on behalf of the guest. This requires
checking that the access is strictly 32bit, properly aligned, and
falls within the expected range.
When all condition are satisfied, we perform the access and tell
the rest of the HYP code that the instruction has been correctly
emulated.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
In order to efficiently perform the GICV access on behalf of the
guest, we need to be able to avoid going back all the way to
the host kernel.
For this, we introduce a new hook in the world switch code,
conveniently placed just after populating the fault info.
At that point, we only have saved/restored the GP registers,
and we can quickly perform all the required checks (data abort,
translation fault, valid faulting syndrome, not an external
abort, not a PTW).
Coming back from the emulation code, we need to skip the emulated
instruction. This involves an additional bit of save/restore in
order to be able to access the guest's PC (and possibly CPSR if
this is a 32bit guest).
At this stage, no emulation code is provided.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
This patch adds compilation and link against irqchip.
Main motivation behind using irqchip code is to enable MSI
routing code. In the future irqchip routing may also be useful
when targeting multiple irqchips.
Routing standard callbacks now are implemented in vgic-irqfd:
- kvm_set_routing_entry
- kvm_set_irq
- kvm_set_msi
They only are supported with new_vgic code.
Both HAVE_KVM_IRQCHIP and HAVE_KVM_IRQ_ROUTING are defined.
KVM_CAP_IRQ_ROUTING is advertised and KVM_SET_GSI_ROUTING is allowed.
So from now on IRQCHIP routing is enabled and a routing table entry
must exist for irqfd injection to succeed for a given SPI. This patch
builds a default flat irqchip routing table (gsi=irqchip.pin) covering
all the VGIC SPI indexes. This routing table is overwritten by the
first first user-space call to KVM_SET_GSI_ROUTING ioctl.
MSI routing setup is not yet allowed.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Going from the ITS structure to the corresponding KVM structure
would be quite handy at times. The kvm_device pointer that is
passed at create time is quite convenient for this, so let's
keep a copy of it in the vgic_its structure.
This will be put to a good use in subsequent patches.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Now that all ITS emulation functionality is in place, we advertise
MSI functionality to userland and also the ITS device to the guest - if
userland has configured that.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
LPIs are dynamically created (mapped) at guest runtime and their
actual number can be quite high, but is mostly assigned using a very
sparse allocation scheme. So arrays are not an ideal data structure
to hold the information.
We use a spin-lock protected linked list to hold all mapped LPIs,
represented by their struct vgic_irq. This lock is grouped between the
ap_list_lock and the vgic_irq lock in our locking order.
Also we store a pointer to that struct vgic_irq in our struct its_itte,
so we can easily access it.
Eventually we call our new vgic_get_lpi() from vgic_get_irq(), so
the VGIC code gets transparently access to LPIs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add emulation for some basic MMIO registers used in the ITS emulation.
This includes:
- GITS_{CTLR,TYPER,IIDR}
- ID registers
- GITS_{CBASER,CREADR,CWRITER}
(which implement the ITS command buffer handling)
- GITS_BASER<n>
Most of the handlers are pretty straight forward, only the CWRITER
handler is a bit more involved by taking the new its_cmd mutex and
then iterating over the command buffer.
The registers holding base addresses and attributes are sanitised before
storing them.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Introduce a new KVM device that represents an ARM Interrupt Translation
Service (ITS) controller. Since there can be multiple of this per guest,
we can't piggy back on the existing GICv3 distributor device, but create
a new type of KVM device.
On the KVM_CREATE_DEVICE ioctl we allocate and initialize the ITS data
structure and store the pointer in the kvm_device data.
Upon an explicit init ioctl from userland (after having setup the MMIO
address) we register the handlers with the kvm_io_bus framework.
Any reference to an ITS thus has to go via this interface.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The ARM GICv3 ITS emulation code goes into a separate file, but needs
to be connected to the GICv3 emulation, of which it is an option.
The ITS MMIO handlers require the respective ITS pointer to be passed in,
so we amend the existing VGIC MMIO framework to let it cope with that.
Also we introduce the basic ITS data structure and initialize it, but
don't return any success yet, as we are not yet ready for the show.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In the GICv3 redistributor there are the PENDBASER and PROPBASER
registers which we did not emulate so far, as they only make sense
when having an ITS. In preparation for that emulate those MMIO
accesses by storing the 64-bit data written into it into a variable
which we later read in the ITS emulation.
We also sanitise the registers, making sure RES0 regions are respected
and checking for valid memory attributes.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In the moment our struct vgic_irq's are statically allocated at guest
creation time. So getting a pointer to an IRQ structure is trivial and
safe. LPIs are more dynamic, they can be mapped and unmapped at any time
during the guest's _runtime_.
In preparation for supporting LPIs we introduce reference counting for
those structures using the kernel's kref infrastructure.
Since private IRQs and SPIs are statically allocated, we avoid actually
refcounting them, since they would never be released anyway.
But we take provisions to increase the refcount when an IRQ gets onto a
VCPU list and decrease it when it gets removed. Also this introduces
vgic_put_irq(), which wraps kref_put and hides the release function from
the callers.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Logically a GICv3 redistributor is assigned to a (v)CPU, so we should
aim to keep redistributor related variables out of our struct vgic_dist.
Let's start by replacing the redistributor related kvm_io_device array
with two members in our existing struct vgic_cpu, which are naturally
per-VCPU and thus don't require any allocation / freeing.
So apart from the better fit with the redistributor design this saves
some code as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Christoffer Dall