Different TPM modules have different width counters which is 16-bit or 32-bit,
the counter width can be read from TPM_PARAM register bit[23:16], this patch
adds dynamic check for counter width to support both 16-bit and 32-bit TPM
modules.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
According to i.MX7ULP reference manual, TPM_SC_CPWMS can ONLY be written when
counter is disabled, TPM_SC_TOF is write-1-clear, TPM_C0SC_CHF is also
write-1-clear, correct these registers initialization flow;
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The clock name should be ipg instead of igp.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The ATMEL_ST config selects MFD_SYSCON, but does not depend on HAS_IOMEM.
Compile testing on architecture without HAS_IOMEM causes "unmet direct
dependencies" in Kconfig phase. Detected by "make ARCH=score allyesconfig".
Add the proper dependency to the ATMEL_ST config.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: https://lkml.kernel.org/r/1520335233-11277-1-git-send-email-yamada.masahiro@socionext.com
These patches remove the metag architecture and tightly dependent
drivers from the kernel. With the 4.16 kernel the ancient gcc 4.2.4
based metag toolchain we have been using is hitting compiler bugs, so
now seems a good time to drop it altogether.
-----BEGIN PGP SIGNATURE-----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=zDIl
-----END PGP SIGNATURE-----
Merge tag 'metag_remove_2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jhogan/metag into asm-generic
Remove metag architecture
These patches remove the metag architecture and tightly dependent
drivers from the kernel. With the 4.16 kernel the ancient gcc 4.2.4
based metag toolchain we have been using is hitting compiler bugs, so
now seems a good time to drop it altogether.
* tag 'metag_remove_2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
i2c: img-scb: Drop METAG dependency
media: img-ir: Drop METAG dependency
watchdog: imgpdc: Drop METAG dependency
MAINTAINERS/CREDITS: Drop METAG ARCHITECTURE
tty: Remove metag DA TTY and console driver
clocksource: Remove metag generic timer driver
irqchip: Remove metag irqchip drivers
Drop a bunch of metag references
docs: Remove remaining references to metag
docs: Remove metag docs
metag: Remove arch/metag/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This series from Keerthy and Ladislav Michl move omap dmtimer code
to drivers. As we don't want to export custom timer functions to
random drivers, we also need to update the related PWM driver to
pass the timer specific functions in platform data.
Note that this series is based on a merge of omap1 specific timer
fix and omap2+ platform data clean-up to keep things working and
make the move a bit simpler.
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEkgNvrZJU/QSQYIcQG9Q+yVyrpXMFAlqdd1IRHHRvbnlAYXRv
bWlkZS5jb20ACgkQG9Q+yVyrpXNziQ/+OywQPRLgeYodIl5AXJCMaZhyFJPN1BP3
OXsDllCnqJOpH4yjIPz4WoEI3ciVRJw+iBOl28pDtomdyejyE9qx/FmIhL081Wgm
T7TgJTieungliRfZu3UWRJdinpEyEzvTtEWlSVWa++lH5Bsub7lIPJsZ3A2bYVMh
9n6uE9bzU/ECdq/1hP9fhM2rssf8mu5l1IKlYmPWuxoFm/YSYoiyneU+rOILnJQ6
dsbc71p3+VdsZBDI+nMGcLE923LGXKEmxlHoR9+9EY12MOIwbTt/jxcI8j+Iugfk
vetncsXbpKnbutTP1iXr64IXa5QFOZKtMNlfNqLo4aihWMJ6tV4570w/pxk/qMgq
+qCidWm9RgVUm1N4t8kMm8aWm1BC1L8g9fw2/l0JFBHcuIlOYewa6cZ6gcUI6XxN
BqcET9iyxG9HgqgB6yekHRI3niywgGcpw420RS0DLmxIzpnpeQHGkXrva0tVcVS7
4SZ9UWgLQVCKgm/8mSDv4PkIzuPXyu4fqjxzMihQdNUHAG1xeqODfU8SLsItW43a
sGojvPPNWhCyvL2hpWuyWsRSOTc8MyAteeowYN1PzoSCO0cI3MTL0TUpxRTBV/9/
y1l5DYmdc1HUARXxJWreBSl3uToADguqzYUv3rHe/B20+LA19F9GRzoc9uOhqTGn
ePjiA5EC64o=
=2B8N
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.17/timer-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Pull "Move omap timer to drivers for 4.17" from Tony Lindgren:
This series from Keerthy and Ladislav Michl move omap dmtimer code
to drivers. As we don't want to export custom timer functions to
random drivers, we also need to update the related PWM driver to
pass the timer specific functions in platform data.
Note that this series is based on a merge of omap1 specific timer
fix and omap2+ platform data clean-up to keep things working and
make the move a bit simpler.
* tag 'omap-for-v4.17/timer-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
clocksource: timer-ti-dm: Check prescaler value
clocksource: timer-ti-dm: Consolidate set source
clocksource: timer-ti-dm: Make unexported functions static
ARM: OMAP: pdata-quirks: Remove unused timer pdata
pwm: pwm-omap-dmtimer: Adapt driver to utilize dmtimer pdata ops
clocksource: timer-ti-dm: Hook device platform data if not already assigned
clocksource: timer-ti-dm: Populate the timer ops to the pdata
clocksource: timer-ti-dm: Add timer ops to the platform data structure
ARM: OMAP: Move dmtimer driver out of plat-omap to drivers under clocksource
clocksource: timer-ti-dm: Replace architecture
ARM: OMAP: Move dmtimer.h out of plat-omap
ARM: OMAP: timer: Wrap the inline functions under OMAP2PLUS define
ARM: OMAP: dmtimer: Remove all the exports
ARM: OMAP: Fix dmtimer init for omap1
Invalid value silently disables use of the prescaler.
Use -1 explicitely for that purpose and error out on
invalid value.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reorder omap_dm_timer_set_source internals to get
source verification more straightforward.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As dmtimer no longer exports functions, make those previously
exported static (this requires few functions to be moved around
as their prototypes were deleted).
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
TIMER0 interrupt ACK is different for ARC700 and HS3x cores.
This came to light in some internal discussions and it is nice to have this
documented rather than digging up the PRM (Programmers Reference Manual).
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Vineet Gupta <Vineet.Gupta1@synopsys.com>
Cc: linux-snps-arc@lists.infradead.org
Link: https://lkml.kernel.org/r/1519241491-12570-1-git-send-email-vgupta@synopsys.com
__gic_clocksource_init() extracts the GIC_CONFIG_COUNTBITS field from
read_gic_config() by right shifting the register value. The shift count is
determined by the most significant bit (__fls) of the bitmask which is
wrong as it shifts out the complete bitfield.
Use the least significant bit (__ffs) instead to shift the bitfield down to
bit 0.
Fixes: e07127a077 ("clocksource: mips-gic-timer: Use new GIC accessor functions")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: daniel.lezcano@linaro.org
Cc: paul.burton@imgtec.com
Link: https://lkml.kernel.org/r/20180228095610.50341-1-nbd@nbd.name
The error checks on freq for a negative error return always fails because
freq is unsigned and can never be negative. Fix this by making freq a
signed long.
Detected with Coccinelle:
drivers/clocksource/fsl_ftm_timer.c:287:5-9: WARNING: Unsigned expression
compared with zero: freq <= 0
drivers/clocksource/fsl_ftm_timer.c:291:5-9: WARNING: Unsigned expression
compared with zero: freq <= 0
Fixes: 2529c3a330 ("clocksource: Add Freescale FlexTimer Module (FTM) timer support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: kernel-janitors@vger.kernel.org
Link: https://lkml.kernel.org/r/20180226113614.3092-1-colin.king@canonical.com
Now that arch/metag/ has been removed, remove the metag generic
per-thread timer driver. It is of no value without the architecture
code.
Signed-off-by: James Hogan <jhogan@kernel.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-metag@vger.kernel.org
In the case of device tree boot the device platform data is usually
NULL so hook the platform data obtained from the match.
As part of un-constify the platform_data pointer.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the timer ops to the platform data
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the dmtimer driver out of plat-omap to clocksource.
So that non-omap devices also could use this.
No Code changes done to the driver file only renamed to timer-ti-dm.c.
Also removed the config dependencies for OMAP_DM_TIMER.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
[tony@atomide.com: add select omap_dm_timer for omap16xx]
Signed-off-by: Tony Lindgren <tony@atomide.com>
On lkml suggestions were made to split up such trivial typo fixes into per subsystem
patches:
--- a/arch/x86/boot/compressed/eboot.c
+++ b/arch/x86/boot/compressed/eboot.c
@@ -439,7 +439,7 @@ setup_uga32(void **uga_handle, unsigned long size, u32 *width, u32 *height)
struct efi_uga_draw_protocol *uga = NULL, *first_uga;
efi_guid_t uga_proto = EFI_UGA_PROTOCOL_GUID;
unsigned long nr_ugas;
- u32 *handles = (u32 *)uga_handle;;
+ u32 *handles = (u32 *)uga_handle;
efi_status_t status = EFI_INVALID_PARAMETER;
int i;
This patch is the result of the following script:
$ sed -i 's/;;$/;/g' $(git grep -E ';;$' | grep "\.[ch]:" | grep -vwE 'for|ia64' | cut -d: -f1 | sort | uniq)
... followed by manual review to make sure it's all good.
Splitting this up is just crazy talk, let's get over with this and just do it.
Reported-by: Pavel Machek <pavel@ucw.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
VDSO needs real-time cycle count to ensure the time accuracy.
Unlike others, nds32 architecture does not define clock source,
hence VDSO needs atcpit100 offering real-time cycle count
to derive the correct time.
Signed-off-by: Vincent Chen <vincentc@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Signed-off-by: Greentime Hu <green.hu@gmail.com>
ATCPIT100 is often used on the Andes architecture,
This timer provide 4 PIT channels. Each PIT channel is a
multi-function timer, can be configured as 32,16,8 bit timers
or PWM as well.
For system timer it will set channel 1 32-bit timer0 as clock
source and count downwards until underflow and restart again.
It also set channel 0 32-bit timer0 as clock event and count
downwards until condition match. It will generate an interrupt
for handling periodically.
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Signed-off-by: Greentime Hu <green.hu@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Add andestech atcpit100 timer
As we have a lot of timers on this platform, we can have potentially all the
timers enabled in the DT, so we don't want to start the timer for every probe
otherwise they will be running for nothing as only one will be used.
Start the timer only when setting the mode or when the clocksource is
enabled.
Tested-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1515418139-23276-20-git-send-email-daniel.lezcano@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add the timer delay callback, that saves us ~90ms of boot time.
Tested-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1515418139-23276-19-git-send-email-daniel.lezcano@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The scene is set for the clocksource functionality, let's add it for this driver.
Tested-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1515418139-23276-18-git-send-email-daniel.lezcano@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In order to prepare the clocksource code, let's factor out the clockevent
code, split the prescaler and timer width code into separate functions.
Tested-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1515418139-23276-17-git-send-email-daniel.lezcano@linaro.org
[ Small edits. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The stm32 timer block is able to have a counter and a comparator.
Instead of using the auto-reload register for periodic events, we switch
to oneshot mode by using the comparator register.
The timer is able to generate an interrupt when the counter overflows but
we don't want that as this counter will be use as a clocksource in the next
patches. So it is disabled by the UDIS bit of the control register.
Tested-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1515418139-23276-16-git-send-email-daniel.lezcano@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The prescaler value is arbitrarily set to 1024 without any regard to the
timer frequency. For 32-bit timers, there is no need to set a prescaler
value as they wrap in an acceptable interval and give the opportunity to
have precise timers on this platform. However, for 16-bit timers a prescaler
value is needed if we don't want to wrap too often per second which is
inefficient and adds more and more error margin. With a targeted clock
of 10MHz, the 16 bits are precise enough whatever the timer frequency is
as we will compute the prescaler.
Tested-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1515418139-23276-15-git-send-email-daniel.lezcano@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In order to clarify and encapsulate the code for upcoming changes, move the
timer width check into a function and add some documentation.
Tested-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1515418139-23276-14-git-send-email-daniel.lezcano@linaro.org
[ Spelling fixes. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
As there are different timers on the stm32, use the node name for the timer
name in order to give the indication of which timer the kernel is using.
/proc/timer_list gives all the information with the right name, otherwise
we end up digging in the kernel log and /proc/interrupt to do the connection
between the used timer.
Tested-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1515418139-23276-13-git-send-email-daniel.lezcano@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Convert the driver to use the timer_of() helpers. This allows the removal of
a custom private structure, factors out and simplifies the code.
[Daniel Lezcano]: Respin against the critical fix patch and massaged the changelog.
Tested-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1515418139-23276-12-git-send-email-daniel.lezcano@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The current code hides a couple of bugs:
- The global variable 'clock_event_ddata' is overwritten each time the
init function is invoked.
This is fixed with a kmemdup() instead of assigning the global variable. That
prevents a memory corruption when several timers are defined in the DT.
- The clockevent's event_handler is NULL if the time framework does
not select the clockevent when registering it, this is fine but the init
code generates in any case an interrupt leading to dereference this
NULL pointer.
The stm32 timer works with shadow registers, a mechanism to cache the
registers. When a change is done in one buffered register, we need to
artificially generate an event to force the timer to copy the content
of the register to the shadowed register.
The auto-reload register (ARR) is one of the shadowed register as well as
the prescaler register (PSC), so in order to force the copy, we issue an
event which in turn leads to an interrupt and the NULL dereference.
This is fixed by inverting two lines where we clear the status register
before enabling the update event interrupt.
As this kernel crash is resulting from the combination of these two bugs,
the fixes are grouped into a single patch.
Tested-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1515418139-23276-11-git-send-email-daniel.lezcano@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When the driver does not specify a name for the resource, don't use
of_io_request_and_map() but of_iomap(). That prevents resource name allocation
conflicts on some platforms which have the same name as the node.
Tested-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1515418139-23276-10-git-send-email-daniel.lezcano@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Under certain circumstances, some specific operations must be done with the
device node pointer, which forces the timer code to propagate the pointer to
the functions which need it.
In order to consolidate the function signatures in the different drivers
by using the timer-of structure, let's store it in the timer-of structure
as a handy pointer when it is needed.
Tested-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1515418139-23276-9-git-send-email-daniel.lezcano@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The Spreadtrum SC9860 platform will use the architected timers as local
clock events, but we also need a broadcast timer device to wake up the
CPUs when the CPUs are in sleep mode.
The Spreadtrum timer can support 32-bit or 64-bit counters, as well as
supporting period mode or one-shot mode.
Signed-off-by: Baolin Wang <baolin.wang@spreadtrum.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1515418139-23276-8-git-send-email-daniel.lezcano@linaro.org
[ Minor readability edits. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The current code has no comments, neither any function descriptions. Fix this by
adding function descriptions in kernel doc format.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1515418139-23276-6-git-send-email-daniel.lezcano@linaro.org
[ Spelling and style fixes. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
All the functions are not prefixed with 'timer_of_', fix the naming in order
to have the code consistent.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1515418139-23276-5-git-send-email-daniel.lezcano@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The clock speed displayed at boot in an information message was 500 kHz
too high compared to its real value. As the value is not used anywhere,
there is no functional impact.
Fix the rounding formula to display the correct value.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1515418139-23276-4-git-send-email-daniel.lezcano@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Actions S700 has two 2Hz timers like S500, and four TIMx timers like S900.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1515418139-23276-3-git-send-email-daniel.lezcano@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The following commit:
1727339590 ("clocksource/drivers: Rename CLOCKSOURCE_OF_DECLARE to TIMER_OF_DECLARE")
deprecated CLOCKSOURCE_OF_DECLARE(), so adopt the new TIMER_OF_DECLARE() macro instead.
Reported-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1515418139-23276-2-git-send-email-daniel.lezcano@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Common:
- Python 3 support in kvm_stat
- Accounting of slabs to kmemcg
ARM:
- Optimized arch timer handling for KVM/ARM
- Improvements to the VGIC ITS code and introduction of an ITS reset
ioctl
- Unification of the 32-bit fault injection logic
- More exact external abort matching logic
PPC:
- Support for running hashed page table (HPT) MMU mode on a host that
is using the radix MMU mode; single threaded mode on POWER 9 is
added as a pre-requisite
- Resolution of merge conflicts with the last second 4.14 HPT fixes
- Fixes and cleanups
s390:
- Some initial preparation patches for exitless interrupts and crypto
- New capability for AIS migration
- Fixes
x86:
- Improved emulation of LAPIC timer mode changes, MCi_STATUS MSRs, and
after-reset state
- Refined dependencies for VMX features
- Fixes for nested SMI injection
- A lot of cleanups
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJaDayXAAoJEED/6hsPKofo/3UH/3HvlcHt+ADTkCU1/iiKAs+i
0zngIOXIxgHDnV0ww6bV+Znww0BzTYgKCAXX76z603jdpDwG/pzQQcbLDF5ZoJnD
sQtF10gZinWaRsHlfbLqjrHGL2pGDHO1UKBKLJ0bAIyORPZBxs7i+VmrY/blnr9c
0wsybJ8RbvwAxjsDL5jeX/z4NehPupmKUc4Lf0eZdSHwVOf9sjn+MP6jJ0r2JcIb
D+zddPBiLStzN97t4gZpQsrlj3LKrDS+6hY+1TjSvlh+yHKFVFh58VhLm4DuDeb5
bYOAlWJ/gAWEzfvr5Ld+Nd7SqWWn/14logPkQ4gcU4BI/neAOzk4c6hJfCHl1nk=
=593n
-----END PGP SIGNATURE-----
Merge tag 'kvm-4.15-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Radim Krčmář:
"First batch of KVM changes for 4.15
Common:
- Python 3 support in kvm_stat
- Accounting of slabs to kmemcg
ARM:
- Optimized arch timer handling for KVM/ARM
- Improvements to the VGIC ITS code and introduction of an ITS reset
ioctl
- Unification of the 32-bit fault injection logic
- More exact external abort matching logic
PPC:
- Support for running hashed page table (HPT) MMU mode on a host that
is using the radix MMU mode; single threaded mode on POWER 9 is
added as a pre-requisite
- Resolution of merge conflicts with the last second 4.14 HPT fixes
- Fixes and cleanups
s390:
- Some initial preparation patches for exitless interrupts and crypto
- New capability for AIS migration
- Fixes
x86:
- Improved emulation of LAPIC timer mode changes, MCi_STATUS MSRs,
and after-reset state
- Refined dependencies for VMX features
- Fixes for nested SMI injection
- A lot of cleanups"
* tag 'kvm-4.15-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (89 commits)
KVM: s390: provide a capability for AIS state migration
KVM: s390: clear_io_irq() requests are not expected for adapter interrupts
KVM: s390: abstract conversion between isc and enum irq_types
KVM: s390: vsie: use common code functions for pinning
KVM: s390: SIE considerations for AP Queue virtualization
KVM: s390: document memory ordering for kvm_s390_vcpu_wakeup
KVM: PPC: Book3S HV: Cosmetic post-merge cleanups
KVM: arm/arm64: fix the incompatible matching for external abort
KVM: arm/arm64: Unify 32bit fault injection
KVM: arm/arm64: vgic-its: Implement KVM_DEV_ARM_ITS_CTRL_RESET
KVM: arm/arm64: Document KVM_DEV_ARM_ITS_CTRL_RESET
KVM: arm/arm64: vgic-its: Free caches when GITS_BASER Valid bit is cleared
KVM: arm/arm64: vgic-its: New helper functions to free the caches
KVM: arm/arm64: vgic-its: Remove kvm_its_unmap_device
arm/arm64: KVM: Load the timer state when enabling the timer
KVM: arm/arm64: Rework kvm_timer_should_fire
KVM: arm/arm64: Get rid of kvm_timer_flush_hwstate
KVM: arm/arm64: Avoid phys timer emulation in vcpu entry/exit
KVM: arm/arm64: Move phys_timer_emulate function
KVM: arm/arm64: Use kvm_arm_timer_set/get_reg for guest register traps
...
Plenty of acronym soup here:
- Initial support for the Scalable Vector Extension (SVE)
- Improved handling for SError interrupts (required to handle RAS events)
- Enable GCC support for 128-bit integer types
- Remove kernel text addresses from backtraces and register dumps
- Use of WFE to implement long delay()s
- ACPI IORT updates from Lorenzo Pieralisi
- Perf PMU driver for the Statistical Profiling Extension (SPE)
- Perf PMU driver for Hisilicon's system PMUs
- Misc cleanups and non-critical fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJaCcLqAAoJELescNyEwWM0JREH/2FbmD/khGzEtP8LW+o9D8iV
TBM02uWQxS1bbO1pV2vb+512YQO+iWfeQwJH9Jv2FZcrMvFv7uGRnYgAnJuXNGrl
W+LL6OhN22A24LSawC437RU3Xe7GqrtONIY/yLeJBPablfcDGzPK1eHRA0pUzcyX
VlyDruSHWX44VGBPV6JRd3x0vxpV8syeKOjbRvopRfn3Nwkbd76V3YSfEgwoTG5W
ET1sOnXLmHHdeifn/l1Am5FX1FYstpcd7usUTJ4Oto8y7e09tw3bGJCD0aMJ3vow
v1pCUWohEw7fHqoPc9rTrc1QEnkdML4vjJvMPUzwyTfPrN+7uEuMIEeJierW+qE=
=0qrg
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"The big highlight is support for the Scalable Vector Extension (SVE)
which required extensive ABI work to ensure we don't break existing
applications by blowing away their signal stack with the rather large
new vector context (<= 2 kbit per vector register). There's further
work to be done optimising things like exception return, but the ABI
is solid now.
Much of the line count comes from some new PMU drivers we have, but
they're pretty self-contained and I suspect we'll have more of them in
future.
Plenty of acronym soup here:
- initial support for the Scalable Vector Extension (SVE)
- improved handling for SError interrupts (required to handle RAS
events)
- enable GCC support for 128-bit integer types
- remove kernel text addresses from backtraces and register dumps
- use of WFE to implement long delay()s
- ACPI IORT updates from Lorenzo Pieralisi
- perf PMU driver for the Statistical Profiling Extension (SPE)
- perf PMU driver for Hisilicon's system PMUs
- misc cleanups and non-critical fixes"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (97 commits)
arm64: Make ARMV8_DEPRECATED depend on SYSCTL
arm64: Implement __lshrti3 library function
arm64: support __int128 on gcc 5+
arm64/sve: Add documentation
arm64/sve: Detect SVE and activate runtime support
arm64/sve: KVM: Hide SVE from CPU features exposed to guests
arm64/sve: KVM: Treat guest SVE use as undefined instruction execution
arm64/sve: KVM: Prevent guests from using SVE
arm64/sve: Add sysctl to set the default vector length for new processes
arm64/sve: Add prctl controls for userspace vector length management
arm64/sve: ptrace and ELF coredump support
arm64/sve: Preserve SVE registers around EFI runtime service calls
arm64/sve: Preserve SVE registers around kernel-mode NEON use
arm64/sve: Probe SVE capabilities and usable vector lengths
arm64: cpufeature: Move sys_caps_initialised declarations
arm64/sve: Backend logic for setting the vector length
arm64/sve: Signal handling support
arm64/sve: Support vector length resetting for new processes
arm64/sve: Core task context handling
arm64/sve: Low-level CPU setup
...
Pull timer updates from Thomas Gleixner:
"Yet another big pile of changes:
- More year 2038 work from Arnd slowly reaching the point where we
need to think about the syscalls themself.
- A new timer function which allows to conditionally (re)arm a timer
only when it's either not running or the new expiry time is sooner
than the armed expiry time. This allows to use a single timer for
multiple timeout requirements w/o caring about the first expiry
time at the call site.
- A new NMI safe accessor to clock real time for the printk timestamp
work. Can be used by tracing, perf as well if required.
- A large number of timer setup conversions from Kees which got
collected here because either maintainers requested so or they
simply got ignored. As Kees pointed out already there are a few
trivial merge conflicts and some redundant commits which was
unavoidable due to the size of this conversion effort.
- Avoid a redundant iteration in the timer wheel softirq processing.
- Provide a mechanism to treat RTC implementations depending on their
hardware properties, i.e. don't inflict the write at the 0.5
seconds boundary which originates from the PC CMOS RTC to all RTCs.
No functional change as drivers need to be updated separately.
- The usual small updates to core code clocksource drivers. Nothing
really exciting"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (111 commits)
timers: Add a function to start/reduce a timer
pstore: Use ktime_get_real_fast_ns() instead of __getnstimeofday()
timer: Prepare to change all DEFINE_TIMER() callbacks
netfilter: ipvs: Convert timers to use timer_setup()
scsi: qla2xxx: Convert timers to use timer_setup()
block/aoe: discover_timer: Convert timers to use timer_setup()
ide: Convert timers to use timer_setup()
drbd: Convert timers to use timer_setup()
mailbox: Convert timers to use timer_setup()
crypto: Convert timers to use timer_setup()
drivers/pcmcia: omap1: Fix error in automated timer conversion
ARM: footbridge: Fix typo in timer conversion
drivers/sgi-xp: Convert timers to use timer_setup()
drivers/pcmcia: Convert timers to use timer_setup()
drivers/memstick: Convert timers to use timer_setup()
drivers/macintosh: Convert timers to use timer_setup()
hwrng/xgene-rng: Convert timers to use timer_setup()
auxdisplay: Convert timers to use timer_setup()
sparc/led: Convert timers to use timer_setup()
mips: ip22/32: Convert timers to use timer_setup()
...
Using the physical counter allows KVM to retain the offset between the
virtual and physical counter as long as it is actively running a VCPU.
As soon as a VCPU is released, another thread is scheduled or we start
running userspace applications, we reset the offset to 0, so that
userspace accessing the virtual timer can still read the virtual counter
and get the same view of time as the kernel.
This opens up potential improvements for KVM performance, but we have to
make a few adjustments to preserve system consistency.
Currently get_cycles() is hardwired to arch_counter_get_cntvct() on
arm64, but as we move to using the physical timer for the in-kernel
time-keeping on systems that boot in EL2, we should use the same counter
for get_cycles() as for other in-kernel timekeeping operations.
Similarly, implementations of arch_timer_set_next_event_phys() is
modified to use the counter specific to the timer being programmed.
VHE kernels or kernels continuing to use the virtual timer are
unaffected.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
As we are about to use the physical counter on arm64 systems that have
KVM support, implement arch_counter_get_cntpct() and the associated
errata workaround functionality for stable timer reads.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The timer-of API does not provide a function to undo what has been done by
the timer_of_init() function.
Add a timer_of_exit() function.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The interrupt handler mfgpt_tick() is not robust versus spurious interrupts
which happen before the clock event device is registered and fully
initialized.
The reason is that the safe guard against spurious interrupts solely checks
for the clockevents shutdown state, but lacks a check for detached
state. If the interrupt hits while the device is in detached state it
passes the safe guard and dereferences the event handler call back which is
NULL.
Add the missing state check.
Fixes: 8f9327cbb6 ("clockevents/drivers/cs5535: Migrate to new 'set-state' interface")
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20171020093103.3317F6004D@linux.fjfi.cvut.cz
Always accessing the compare register via the CM redirect region is
(relatively) slow. If the timer being updated is the current CPUs
then this can be shortcutted by writing to the CM VP local region.
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The function gic_next_event is always called with interrupts disabled, so
the local_irq_save / local_irq_restore are pointless - remove them.
[Daniel Lezcano: Fixed warning by removing unused variable 'flags']
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Our ctags mangling script can't handle newlines inside of a
DEFINE_PER_CPU(), leading to an annoying message whenever tags are
built:
ctags: Warning: drivers/clocksource/arm_arch_timer.c:302: null expansion of name pattern "\1"
This was dealt with elsewhere in commit:
25528213fe ("tags: Fix DEFINE_PER_CPU expansions")
... by ensuring each DEFINE_PER_CPU() was contained on a single line,
even where this would violate the usual code style (checkpatch warnings
and all).
Let's do the same for the arch timer driver, and get rid of the
distraction.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The ACPI GTDT code validates the CNTFRQ field of each MMIO timer
frame against the CNTFRQ system register of the current CPU, to
ensure that they are equal, which is mandated by the architecture.
However, reading the CNTFRQ field of a frame is not possible until
the RFRQ bit in the frame's CNTACRn register is set, and doing so
before that willl produce the following error:
arch_timer: [Firmware Bug]: CNTFRQ mismatch: frame @ 0x00000000e0be0000: (0x00000000), CPU: (0x0ee6b280)
arch_timer: Disabling MMIO timers due to CNTFRQ mismatch
arch_timer: Failed to initialize memory-mapped timer.
The reason is that the CNTFRQ field is RES0 if access is not enabled.
So move the validation of CNTFRQ into the loop that iterates over the
timers to find the best frame, but defer it until after we have selected
the best frame, which should also have enabled the RFRQ bit.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
We regularly run into build errors when a clocksource driver selects
CONFIG_TIMER_OF while CONFIG_GENERIC_CLOCKEVENTS is disabled:
In file included from drivers/clocksource/timer-of.c:25:0:
drivers/clocksource/timer-of.h:35:28: error: field 'clkevt' has incomplete type
At the moment, three drivers can show this behavior: ARMV7M_SYSTICK,
CLKSRC_ST_LPC and CLKSRC_NPS. We could add further dependencies as we did
many times, but I have looked a little bit more at what architectures
are left that don't use GENERIC_CLOCKEVENTS, and this shows that there
is a better solution.
On arch/frv and arch/ia64, we never select CONFIG_GENERIC_CLOCKEVENTS
and we also don't use ARCH_USES_GETTIMEOFFSET, which would
block the clocksource Kconfig menu. On m68k, some platforms use
CONFIG_GENERIC_CLOCKEVENTS, some use ARCH_USES_GETTIMEOFFSET, and some
use neither of them. The good news is that there is no configuration that
does not set CONFIG_GENERIC_CLOCKEVENTS but that wants to enable any of
the Kconfig symbols in the menu, so we can simply replace the dependency
with the stricter one. While in theory one could have a clocksource
driver without the clockevent infrastructure, this seems unlikely
to be relevant in the future any more.
We can probably drop some of the other dependencies as well now,
e.g. there should generally be no reason to depend on CONFIG_ARM
unless the driver uses architecture specific assembly.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
pr_err() messages should end with a new-line to avoid other messages being
concatenated.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
pr_err() messages should end with a new-line to avoid other messages being
concatenated.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
pr_err() messages should end with a new-line to avoid other messages being
concatenated.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Use the existing of_device_get_match_data() helper instead of
open-coding its functionality.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The in-driver channel configuration in sh_cmt_info.channels_mask is now
always set for all CMT devices instantiated from DT.
Hence the "renesas,channels-mask" property is no longer checked, and its
handling can be removed, cfr. commit 4e18111ff3 ("devicetree:
bindings: Remove deprecated properties").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Document in the driver that "renesas,cmt-48-gen2" is deprecated, but
still supported for backward compatibility with old DTBs, cfr. commit
4e18111ff3 ("devicetree: bindings: Remove deprecated
properties").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Remove driver matching support for the unused "renesas,cmt-32" and
"renesas,cmt-32-fast" compatible values, cfr. commit 203bb34799
("devicetree: bindings: Remove unused 32-bit CMT bindings").
As this removes the last user of SH_CMT_32BIT_FAST, all support for this
variant is removed from the driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Add support for the new R-Car Gen2 CMT0 and CMT1 bindings. Support
for the old DT binding is still kept around, however devices using
such binding will be treated as a low-feature CMT0 device. If users
want to make use of CMT1-specific features then they need to update
their DTBs. No special CMT1-specific features are however implemented
by his patch, only DT bindings are redone as groundwork for future
feature patches.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Always use 0x3f as channel mask for the SH_CMT_48BIT type of devices.
Once this patch is applied the "renesas,channels-mask" property will
be ignored by the driver for older devices matching SH_CMT_48BIT. In
the future when all CMT types store channel mask in the driver then
we will be able to deprecate and remove "renesas,channels-mask" from DTS.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The arch timer configuration for a CPU might get reset after suspending
said CPU.
In order to reliably use the event stream in the kernel (e.g. for delays),
we keep track of the state where we can safely consider the event stream as
properly configured. After writing to cntkctl, we issue an ISB to ensure
that subsequent delay loops can rely on the event stream being enabled.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
gcc-4.6 and older fail to inline integrator_clocksource_init, so they
end up showing a harmless warning:
WARNING: vmlinux.o(.text+0x4aa94c): Section mismatch in reference from the function integrator_clocksource_init() to the function .init.text:clocksource_mmio_init()
The function integrator_clocksource_init() references
the function __init clocksource_mmio_init().
This is often because integrator_clocksource_init lacks a __init
annotation or the annotation of clocksource_mmio_init is wrong.
Add the missing __init annotation that makes it build cleanly with all
compilers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: http://lkml.kernel.org/r/20170915194310.1170514-1-arnd@arndb.de
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 4.14 for MIPS; below a summary of
the non-merge commits:
CM:
- Rename mips_cm_base to mips_gcr_base
- Specify register size when generating accessors
- Use BIT/GENMASK for register fields, order & drop shifts
- Add cluster & block args to mips_cm_lock_other()
CPC:
- Use common CPS accessor generation macros
- Use BIT/GENMASK for register fields, order & drop shifts
- Introduce register modify (set/clear/change) accessors
- Use change_*, set_* & clear_* where appropriate
- Add CM/CPC 3.5 register definitions
- Use GlobalNumber macros rather than magic numbers
- Have asm/mips-cps.h include CM & CPC headers
- Cluster support for topology functions
- Detect CPUs in secondary clusters
CPS:
- Read GIC_VL_IDENT directly, not via irqchip driver
DMA:
- Consolidate coherent and non-coherent dma_alloc code
- Don't use dma_cache_sync to implement fd_cacheflush
FPU emulation / FP assist code:
- Another series of 14 commits fixing corner cases such as NaN
propgagation and other special input values.
- Zero bits 32-63 of the result for a CLASS.D instruction.
- Enhanced statics via debugfs
- Do not use bools for arithmetic. GCC 7.1 moans about this.
- Correct user fault_addr type
Generic MIPS:
- Enhancement of stack backtraces
- Cleanup from non-existing options
- Handle non word sized instructions when examining frame
- Fix detection and decoding of ADDIUSP instruction
- Fix decoding of SWSP16 instruction
- Refactor handling of stack pointer in get_frame_info
- Remove unreachable code from force_fcr31_sig()
- Convert to using %pOF instead of full_name
- Remove the R6000 support.
- Move FP code from *_switch.S to *_fpu.S
- Remove unused ST_OFF from r2300_switch.S
- Allow platform to specify multiple its.S files
- Add #includes to various files to ensure code builds reliable and
without warning..
- Remove __invalidate_kernel_vmap_range
- Remove plat_timer_setup
- Declare various variables & functions static
- Abstract CPU core & VP(E) ID access through accessor functions
- Store core & VP IDs in GlobalNumber-style variable
- Unify checks for sibling CPUs
- Add CPU cluster number accessors
- Prevent direct use of generic_defconfig
- Make CONFIG_MIPS_MT_SMP default y
- Add __ioread64_copy
- Remove unnecessary inclusions of linux/irqchip/mips-gic.h
GIC:
- Introduce asm/mips-gic.h with accessor functions
- Use new GIC accessor functions in mips-gic-timer
- Remove counter access functions from irq-mips-gic.c
- Remove gic_read_local_vp_id() from irq-mips-gic.c
- Simplify shared interrupt pending/mask reads in irq-mips-gic.c
- Simplify gic_local_irq_domain_map() in irq-mips-gic.c
- Drop gic_(re)set_mask() functions in irq-mips-gic.c
- Remove gic_set_polarity(), gic_set_trigger(), gic_set_dual_edge(),
gic_map_to_pin() and gic_map_to_vpe() from irq-mips-gic.c.
- Convert remaining shared reg access, local int mask access and
remaining local reg access to new accessors
- Move GIC_LOCAL_INT_* to asm/mips-gic.h
- Remove GIC_CPU_INT* macros from irq-mips-gic.c
- Move various definitions to the driver
- Remove gic_get_usm_range()
- Remove __gic_irq_dispatch() forward declaration
- Remove gic_init()
- Use mips_gic_present() in place of gic_present and remove
gic_present
- Move gic_get_c0_*_int() to asm/mips-gic.h
- Remove linux/irqchip/mips-gic.h
- Inline __gic_init()
- Inline gic_basic_init()
- Make pcpu_masks a per-cpu variable
- Use pcpu_masks to avoid reading GIC_SH_MASK*
- Clean up mti, reserved-cpu-vectors handling
- Use cpumask_first_and() in gic_set_affinity()
- Let the core set struct irq_common_data affinity
microMIPS:
- Fix microMIPS stack unwinding on big endian systems
MIPS-GIC:
- SYNC after enabling GIC region
NUMA:
- Remove the unused parent_node() macro
R6:
- Constify r2_decoder_tables
- Add accessor & bit definitions for GlobalNumber
SMP:
- Constify smp ops
- Allow boot_secondary SMP op to return errors
VDSO:
- Drop gic_get_usm_range() usage
- Avoid use of linux/irqchip/mips-gic.h
Platform changes:
Alchemy:
- Add devboard machine type to cpuinfo
- update cpu feature overrides
- Threaded carddetect irqs for devboards
AR7:
- allow NULL clock for clk_get_rate
BCM63xx:
- Fix ENETDMA_6345_MAXBURST_REG offset
- Allow NULL clock for clk_get_rate
CI20:
- Enable GPIO and RTC drivers in defconfig
- Add ethernet and fixed-regulator nodes to DTS
Generic platform:
- Move Boston and NI 169445 FIT image source to their own files
- Include asm/bootinfo.h for plat_fdt_relocated()
- Include asm/time.h for get_c0_*_int()
- Include asm/bootinfo.h for plat_fdt_relocated()
- Include asm/time.h for get_c0_*_int()
- Allow filtering enabled boards by requirements
- Don't explicitly disable CONFIG_USB_SUPPORT
- Bump default NR_CPUS to 16
JZ4700:
- Probe the jz4740-rtc driver from devicetree
Lantiq:
- Drop check of boot select from the spi-falcon driver.
- Drop check of boot select from the lantiq-flash MTD driver.
- Access boot cause register in the watchdog driver through regmap
- Add device tree binding documentation for the watchdog driver
- Add docs for the RCU DT bindings.
- Convert the fpi bus driver to a platform_driver
- Remove ltq_reset_cause() and ltq_boot_select(
- Switch to a proper reset driver
- Switch to a new drivers/soc GPHY driver
- Add an USB PHY driver for the Lantiq SoCs using the RCU module
- Use of_platform_default_populate instead of __dt_register_buses
- Enable MFD_SYSCON to be able to use it for the RCU MFD
- Replace ltq_boot_select() with dummy implementation.
Loongson 2F:
- Allow NULL clock for clk_get_rate
Malta:
- Use new GIC accessor functions
NI 169445:
- Add support for NI 169445 board.
- Only include in 32r2el kernels
Octeon:
- Add support for watchdog of 78XX SOCs.
- Add support for watchdog of CN68XX SOCs.
- Expose support for mips32r1, mips32r2 and mips64r1
- Enable more drivers in config file
- Add support for accessing the boot vector.
- Remove old boot vector code from watchdog driver
- Define watchdog registers for 70xx, 73xx, 78xx, F75xx.
- Make CSR functions node aware.
- Allow access to CIU3 IRQ domains.
- Misc cleanups in the watchdog driver
Omega2+:
- New board, add support and defconfig
Pistachio:
- Enable Root FS on NFS in defconfig
Ralink:
- Add Mediatek MT7628A SoC
- Allow NULL clock for clk_get_rate
- Explicitly request exclusive reset control in the pci-mt7620 PCI driver.
SEAD3:
- Only include in 32 bit kernels by default
VoCore:
- Add VoCore as a vendor t0 dt-bindings
- Add defconfig file"
* '4.14-features' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (167 commits)
MIPS: Refactor handling of stack pointer in get_frame_info
MIPS: Stacktrace: Fix microMIPS stack unwinding on big endian systems
MIPS: microMIPS: Fix decoding of swsp16 instruction
MIPS: microMIPS: Fix decoding of addiusp instruction
MIPS: microMIPS: Fix detection of addiusp instruction
MIPS: Handle non word sized instructions when examining frame
MIPS: ralink: allow NULL clock for clk_get_rate
MIPS: Loongson 2F: allow NULL clock for clk_get_rate
MIPS: BCM63XX: allow NULL clock for clk_get_rate
MIPS: AR7: allow NULL clock for clk_get_rate
MIPS: BCM63XX: fix ENETDMA_6345_MAXBURST_REG offset
mips: Save all registers when saving the frame
MIPS: Add DWARF unwinding to assembly
MIPS: Make SAVE_SOME more standard
MIPS: Fix issues in backtraces
MIPS: jz4780: DTS: Probe the jz4740-rtc driver from devicetree
MIPS: Ci20: Enable RTC driver
watchdog: octeon-wdt: Add support for 78XX SOCs.
watchdog: octeon-wdt: Add support for cn68XX SOCs.
watchdog: octeon-wdt: File cleaning.
...
Pull timer fixes from Thomas Gleixner:
"A rather small update for the time(r) subsystem:
- A new clocksource driver IMX-TPM
- Minor fixes to the alarmtimer facility
- Device tree cleanups for Renesas drivers
- A new kselftest and fixes for the timer related tests
- Conversion of the clocksource drivers to use %pOF
- Use the proper helpers to access rlimits in the posix-cpu-timer
code"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
alarmtimer: Ensure RTC module is not unloaded
clocksource: Convert to using %pOF instead of full_name
clocksource/drivers/bcm2835: Remove message for a memory allocation failure
devicetree: bindings: Remove deprecated properties
devicetree: bindings: Remove unused 32-bit CMT bindings
devicetree: bindings: Deprecate property, update example
devicetree: bindings: r8a73a4 and R-Car Gen2 CMT bindings
devicetree: bindings: R-Car Gen2 CMT0 and CMT1 bindings
devicetree: bindings: Remove sh7372 CMT binding
clocksource/drivers/imx-tpm: Add imx tpm timer support
dt-bindings: timer: Add nxp tpm timer binding doc
posix-cpu-timers: Use dedicated helper to access rlimit values
alarmtimer: Fix unavailable wake-up source in sysfs
timekeeping: Use proper timekeeper for debug code
kselftests: timers: set-timer-lat: Add one-shot timer test cases
kselftests: timers: set-timer-lat: Tweak reporting when timer fires early
kselftests: timers: freq-step: Fix build warning
kselftests: timers: freq-step: Define ADJ_SETOFFSET if device has older kernel headers
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: linux-arm-kernel@lists.infradead.org
Acked-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Switch from calling functions exported by the GIC interrupt controller
to using new accessors provided by asm/mips-gic.h. This will allow the
counter-handling functionality to be removed from the interrupt
controller driver, where it doesn't really belong, and also allow for
inlining of the accesses to the GIC.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17021/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The bcm2835_timer_init() function emits an error message in case of a memory
allocation failure. This is pointless as the mm core does that already.
Remove this message.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
IMX Timer/PWM Module (TPM) supports both timer and pwm function while
this patch only adds the timer support. PWM would be added later.
The TPM counter, compare and capture registers are clocked by an
asynchronous clock that can remain enabled in low power modes.
NOTE: We observed in a very small probability, the bus fabric
contention between GPU and A7 may results a few cycles delay
of writing CNT registers which may cause the min_delta event got
missed, so we need add a ETIME check here in case it happened.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Anson Huang <Anson.Huang@nxp.com>
Cc: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
In v4.13, CLKSRC_PISTACHIO can select TIMER_OF on architectures without
GENERIC_CLOCKEVENTS, resulting in a struct clock_event_device missing
some required features and build breakage compiling timer_of.c. One of
the symbols selecting TIMER_OF is CLKSRC_PISTACHIO, so add the
dependency on GENERIC_CLOCKEVENTS.
Thanks to kbuild test robot for finding this error
(https://lkml.org/lkml/2017/7/16/249)
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Suggested-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The current code checks the return value of the of_io_request_and_map()
function as it was returning a NULL pointer in case of error.
However, it returns an error code encoded in the pointer return value, not a
NULL value. Fix this by checking the returned pointer against IS_ERR() and
return the error with PTR_ERR().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Propagate the return values of platform_get_irq and devm_request_irq on
failure.
Cc: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The loop to find the best memory frame in arch_timer_mem_acpi_init()
initializes the loop counter with itself ('i = i'), which is suspicious
in the first place and pointed out by clang. The loop condition is
'i < timer_count' and a prior for loop exits when 'i' reaches
'timer_count', therefore the second loop is never executed.
Initialize the loop counter with 0 to iterate over all timers, which
supposedly was the intention before the typo monster attacked.
Fixes: c2743a3676 ("clocksource: arm_arch_timer: add GTDT support for memory-mapped timer")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Use the new static_branch_enable_cpuslocked() function to switch
the workaround static key on the CPU hotplug path.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/20170801080257.5056-5-marc.zyngier@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
of_irq_get_byname() may return a negative error number as well as 0 on
failure, while timer_irq_init() only checks for 0, blithely continuing with
the call to request_[percpu_]irq() -- those functions expect *unsigned int*,
so would probably fail anyway when a large IRQ number resulting from a
conversion of a negative error number is passed to them... This, however,
is incorrect behavior -- error number is not IRQ number.
Filter out the negative error numbers, complain, and return them to the
timer_irq_init()'s callers...
Fixes: dc11bae785 ("clocksource/drivers: Add timer-of common init routine")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: http://lkml.kernel.org/r/20170717180114.678825147@cogentembedded.com
- New SoC specific drivers
- NVIDIA Tegra PM Domain support for newer SoCs (Tegra186 and later)
based on the "BPMP" firmware
- Clocksource and system controller drivers for the newly added
Action Semi platforms (both arm and arm64).
- Reset subsystem, merged through arm-soc by tradition:
- New drivers for Altera Stratix10, TI Keystone and Cortina Gemini SoCs
- Various subsystem-wide cleanups
- Updates for existing SoC-specific drivers
- TI GPMC (General Purpose Memory Controller)
- Mediatek "scpsys" system controller support for MT6797
- Broadcom "brcmstb_gisb" bus arbitrer
- ARM SCPI firmware
- Renesas "SYSC" system controller
One more driver update was submitted for the Freescale/NXP DPAA
data path acceleration that has previously been used on PowerPC
chips. I ended up postponing the merge until some API questions
for its unusual MMIO access are resolved.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5L6n
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"New SoC specific drivers:
- NVIDIA Tegra PM Domain support for newer SoCs (Tegra186 and later)
based on the "BPMP" firmware
- Clocksource and system controller drivers for the newly added
Action Semi platforms (both arm and arm64).
Reset subsystem, merged through arm-soc by tradition:
- New drivers for Altera Stratix10, TI Keystone and Cortina Gemini
SoCs
- Various subsystem-wide cleanups
Updates for existing SoC-specific drivers
- TI GPMC (General Purpose Memory Controller)
- Mediatek "scpsys" system controller support for MT6797
- Broadcom "brcmstb_gisb" bus arbitrer
- ARM SCPI firmware
- Renesas "SYSC" system controller
One more driver update was submitted for the Freescale/NXP DPAA data
path acceleration that has previously been used on PowerPC chips. I
ended up postponing the merge until some API questions for its unusual
MMIO access are resolved"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (35 commits)
clocksource: owl: Add S900 support
clocksource: Add Owl timer
soc: renesas: rcar-sysc: Use GENPD_FLAG_ALWAYS_ON
firmware: tegra: Fix locking bugs in BPMP
soc/tegra: flowctrl: Fix error handling
soc/tegra: bpmp: Implement generic PM domains
soc/tegra: bpmp: Update ABI header
PM / Domains: Allow overriding the ->xlate() callback
soc: brcmstb: enable drivers for ARM64 and BMIPS
soc: renesas: Rework Kconfig and Makefile logic
reset: Add the TI SCI reset driver
dt-bindings: reset: Add TI SCI reset binding
reset: use kref for reference counting
soc: qcom: smsm: Improve error handling, quiesce probe deferral
cpufreq: scpi: use new scpi_ops functions to remove duplicate code
firmware: arm_scpi: add support to populate OPPs and get transition latency
dt-bindings: reset: Add reset manager offsets for Stratix10
memory: omap-gpmc: add error message if bank-width property is absent
memory: omap-gpmc: make dts snippet include semicolon
reset: Add a Gemini reset controller
...
'clk' is a valid pointer at this point. So calling PTR_ERR on it is
pointess.
Return the error code from 'clk_prepare_enable()' if it fails instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
In case of error at init time, rollback iomapping.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Now that AVR32 is gone, we can use the proper IO accessors that are
correctly handling endianness.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Previously a framework to factor out the drivers init function has been
merged.
Use this common framework in this driver, we get:
Before:
text data bss dec hex filename
1787 384 12 2183 887 drivers/clocksource/sun4i_timer.o
After:
text data bss dec hex filename
1407 512 0 1919 77f drivers/clocksource/sun4i_timer.o
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Chen-Yu Tsai <wens@csie.org>
A typo in the code checks the return value of iomap against !NULL
and, thus, fails everytime the mapping succeed.
Fix this by inverting the condition in the check.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
If none of the flags are set, 'ret' is uninitialized as pointed out
by gcc:
drivers/clocksource/timer-of.c: In function 'timer_of_init':
drivers/clocksource/timer-of.c:160:9: error: 'ret' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Since calling the function without any of the flags is an error,
set the return value to -EINVAL for that case.
[ tglx: Get rid of the silly backwards goto while at it ]
Fixes: dc11bae785 ("clocksource/drivers: Add timer-of common init routine")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: http://lkml.kernel.org/r/20170621215005.3870011-1-arnd@arndb.de
The Actions Semi S500 SoC provides four timers, 2Hz0/1 and 32-bit TIMER0/1.
Use TIMER0 as clocksource and TIMER1 as clockevents.
Based on LeMaker linux-actions tree.
An S500 datasheet can be found on the LeMaker Guitar pages:
http://www.lemaker.org/product-guitar-download-29.html
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
The sched_clock() and delay timer callbacks can just call
each other and we can save an #ifdef.
Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Joel Stanley <joel@jms.id.au>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This timer is often used on the ARM architecture, so as with so
many siblings, we can implement delay timers, removing the need
for the system to calibrate jiffys at boot, and potentially
handling CPU frequency scaling on targets.
We cannot just protect the Kconfig with a "depends on ARM" because
it is already known that different architectures are using Faraday
IP blocks, so it is better to make things open-ended and use
Result on boot dmesg:
Switching to timer-based delay loop, resolution 40n
Calibrating delay loop (skipped), value calculated using
timer frequency.. 50.00 BogoMIPS (lpj=250000)
This is accurately the timer frequency, 250MHz on the APB
bus.
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Joel Stanley <joel@jms.id.au>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Jonas Jensen <jonas.jensen@gmail.com>
Tested-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The different drivers are all using the same pattern when initializing.
1. Get the base address
2. Get the irq number
3. Get the clock
4. Prepare and enable the clock
5. Get the rate
6. Request an interrupt
Instead of repeating again and again these steps in all the drivers, let's
provide a common init routine to give the opportunity to factor all of them
out.
We can expect a significant kernel size improvement when the common routine
will be used in all the drivers.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
On sama5d2, power to the core may be cut while entering suspend mode. It is
necessary to save and restore the TCB registers.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The sched_clock() call should be really fast so we want to
avoid an extra if() clause on the read path if possible.
Implement two sched_clock_read() functions, one if the timer
counts up and one if it counts down. Incidentally this also
mirrors how clocksource_mmio_init() works and make things
simple and easy to understand.
Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Joel Stanley <joel@jms.id.au>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The config option name is now renamed to 'TIMER_ACPI' for consistency with
the CLOCKSOURCE_OF_DECLARE => TIMER_OF_DECLARE change.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The config option name is now renamed to 'TIMER_OF' for consistency with
the CLOCKSOURCE_OF_DECLARE => TIMER_OF_DECLARE change.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The table name is now renamed to 'timer' for consistency with
the CLOCKSOURCE_OF_DECLARE => TIMER_OF_DECLARE change.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The macro name is now renamed to 'TIMER_ACPI_DECLARE' for consistency
with the CLOCKSOURCE_OF_DECLARE => TIMER_OF_DECLARE change.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The function name is now renamed to 'timer_probe' for consistency with
the CLOCKSOURCE_OF_DECLARE => TIMER_OF_DECLARE change.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Anson Huang