Make sure to invoke pci_disable_device() when errors occur in
pcnet32_probe_pci().
Signed-off-by: Bo Chen <chenbo@pdx.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SFP eeprom indicates the transceiver signals (Rx LOS, Tx Fault, etc.)
that it supports. Update the driver to include checking the eeprom data
when deciding whether to use a transceiver signal.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update xgbe-phy-v2.c to make use of the auto-negotiation (AN) phy hooks
to improve the ability to successfully complete Clause 73 AN when running
at 10gbps. Hardware can sometimes have issues with CDR lock when the
AN DME page exchange is being performed.
The AN and KR training hooks are used as follows:
- The pre AN hook is used to disable CDR tracking in the PHY so that the
DME page exchange can be successfully and consistently completed.
- The post KR training hook is used to re-enable the CDR tracking so that
KR training can successfully complete.
- The post AN hook is used to check for an unsuccessful AN which will
increase a CDR tracking enablement delay (up to a maximum value).
Add two debugfs entries to allow control over use of the CDR tracking
workaround. The debugfs entries allow the CDR tracking workaround to
be disabled and determine whether to re-enable CDR tracking before or
after link training has been initiated.
Also, with these changes the receiver reset cycle that is performed during
the link status check can be performed less often.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hooks to the driver auto-negotiation (AN) flow to allow the different
phy implementations to perform any steps necessary to improve AN.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefer the direct use of octal for permissions.
Done with checkpatch -f --types=SYMBOLIC_PERMS --fix-inplace
and some typing.
Miscellanea:
o Whitespace neatening around these conversions.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable tx_index is being initialized with a value that is never
read and re-assigned a little later, hence the initialization is redundant
and can be removed.
Cleans up clang warning:
drivers/net/ethernet/amd/amd8111e.c:652:6: warning: Value stored to
'tx_index' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After resuming from suspend, the PCI device support must re-enable the
interrupt setting so that interrupts are actually delivered.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to a typo, the mask was destroyed by a comparison instead of a bit
shift.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of yet another custom hex_dump_to_buffer().
The output is slightly changed, i.e. each byte followed by white space.
Note, we don't use print_hex_dump() here since the original code uses
nedev_dbg().
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge updates from Andrew Morton:
- a few misc bits
- ocfs2 updates
- almost all of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (131 commits)
memory hotplug: fix comments when adding section
mm: make alloc_node_mem_map a void call if we don't have CONFIG_FLAT_NODE_MEM_MAP
mm: simplify nodemask printing
mm,oom_reaper: remove pointless kthread_run() error check
mm/page_ext.c: check if page_ext is not prepared
writeback: remove unused function parameter
mm: do not rely on preempt_count in print_vma_addr
mm, sparse: do not swamp log with huge vmemmap allocation failures
mm/hmm: remove redundant variable align_end
mm/list_lru.c: mark expected switch fall-through
mm/shmem.c: mark expected switch fall-through
mm/page_alloc.c: broken deferred calculation
mm: don't warn about allocations which stall for too long
fs: fuse: account fuse_inode slab memory as reclaimable
mm, page_alloc: fix potential false positive in __zone_watermark_ok
mm: mlock: remove lru_add_drain_all()
mm, sysctl: make NUMA stats configurable
shmem: convert shmem_init_inodecache() to void
Unify migrate_pages and move_pages access checks
mm, pagevec: rename pagevec drained field
...
As the page free path makes no distinction between cache hot and cold
pages, there is no real useful ordering of pages in the free list that
allocation requests can take advantage of. Juding from the users of
__GFP_COLD, it is likely that a number of them are the result of copying
other sites instead of actually measuring the impact. Remove the
__GFP_COLD parameter which simplifies a number of paths in the page
allocator.
This is potentially controversial but bear in mind that the size of the
per-cpu pagelists versus modern cache sizes means that the whole per-cpu
list can often fit in the L3 cache. Hence, there is only a potential
benefit for microbenchmarks that alloc/free pages in a tight loop. It's
even worse when THP is taken into account which has little or no chance
of getting a cache-hot page as the per-cpu list is bypassed and the
zeroing of multiple pages will thrash the cache anyway.
The truncate microbenchmarks are not shown as this patch affects the
allocation path and not the free path. A page fault microbenchmark was
tested but it showed no sigificant difference which is not surprising
given that the __GFP_COLD branches are a miniscule percentage of the
fault path.
Link: http://lkml.kernel.org/r/20171018075952.10627-9-mgorman@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change TC_SETUP_MQPRIO to TC_SETUP_QDISC_MQPRIO to match the new
convention.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Allen Pais <allen.lkml@gmail.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jarod Wilson <jarod@redhat.com>
Cc: Philippe Reynes <tremyfr@gmail.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- removal of the old dma_alloc_noncoherent interface
- remove unused flags to dma_declare_coherent_memory
- restrict OF DMA configuration to specific physical busses
- use the iommu mailing list for dma-mapping questions and
patches
-----BEGIN PGP SIGNATURE-----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=qHNs
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.14' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- removal of the old dma_alloc_noncoherent interface
- remove unused flags to dma_declare_coherent_memory
- restrict OF DMA configuration to specific physical busses
- use the iommu mailing list for dma-mapping questions and patches
* tag 'dma-mapping-4.14' of git://git.infradead.org/users/hch/dma-mapping:
dma-coherent: fix dma_declare_coherent_memory() logic error
ARM: imx: mx31moboard: Remove unused 'dma' variable
dma-coherent: remove an unused variable
MAINTAINERS: use the iommu list for the dma-mapping subsystem
dma-coherent: remove the DMA_MEMORY_MAP and DMA_MEMORY_IO flags
dma-coherent: remove the DMA_MEMORY_INCLUDES_CHILDREN flag
of: restrict DMA configuration
dma-mapping: remove dma_alloc_noncoherent and dma_free_noncoherent
i825xx: switch to switch to dma_alloc_attrs
au1000_eth: switch to dma_alloc_attrs
sgiseeq: switch to dma_alloc_attrs
dma-mapping: reduce dma_mapping_error inline bloat
There is a difference in the bit position of the normal interrupt summary
enable (NIE) and abnormal interrupt summary enable (AIE) between revisions
of the hardware. For older revisions the NIE and AIE bits are positions
16 and 15 respectively. For newer revisions the NIE and AIE bits are
positions 15 and 14. The effect in changing the bit position is that
newer hardware won't receive AIE interrupts in the current version of the
driver. Specifically, the driver uses this interrupt to collect
statistics on when a receive buffer unavailable event occurs and to
restart the driver/device when a fatal bus error occurs.
Update the driver to set the interrupt enable bit based on the reported
version of the hardware.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dma_alloc_attrs directly instead of the dma_alloc_noncoherent wrapper.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: David S. Miller <davem@davemloft.net>
zorro_device_id are not supposed to change at runtime. All functions
working with zorro_device_id provided by <linux/zorro.h> work with
const zorro_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some additional statistics for tracking VXLAN packets and checksum
errors.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware has the capability to perform checksum offload support
(both Tx and Rx) and TSO support for VXLAN packets. Add the support
required to enable this.
The hardware can only support a single VXLAN port for offload. If more
than one VXLAN port is added then the offload capabilities have to be
disabled and can no longer be advertised.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert from using the old u32 supported, advertising, etc. link settings
to the new link mode settings that support bit positions / settings
greater than 32 bits.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add per queue Tx and Rx packet and byte counts.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the dynamic debug support to output information about the hardware
features reported by the device.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently whenever the driver needs to enable or disable interrupts for
a DMA channel it reads the interrupt enable register (IER), updates the
value and then writes the new value back to the IER. Since the hardware
does not change the IER, software can track this value and elimiate the
need to read it each time.
Add the IER value to the channel related data structure and use that as
the base for enabling and disabling interrupts, thus removing the need
for the MMIO read.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some additional dynamic debug message to the driver. The new messages
will provide additional information about the PCS window calculation.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many of the names used by the driver are based upon the name of the device
found during device probe. Move the formatting of the names into the
device open function so that any renaming that occurs before the device is
brought up will be accounted for. This also means moving the creation of
some named workqueues into the device open path.
Add support to register for net events so that if a device is renamed
the corresponding debugfs directory can be renamed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When transmitting a TSO packet, the driver only increments the TSO packet
statistic by one rather than the number of total packets that were sent.
Update the driver to record the total number of packets that resulted from
TSO transmit.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes when the driver is being unloaded while the devices are still
up the driver can issue errors. This is based on timing and the double
invocation of some routines. The phy_exit() call needs to be run after
the network device has been closed and unregistered from the system.
Also, the phy_exit() does not need to invoke phy_stop() since that will
be called as part of the device closing, so remove that call.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running in SGMII mode at speeds below 1000Mbps, the auto-negotition
control register must set the MII control width for the MAC interface
to be 8-bits wide. By default the width is 4-bits.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the MDIO mode is set to none for the 10000Base-T, which is
incorrect. The MDIO mode should for this configuration should be
clause 45.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of struct tc_to_netdev which is now just unnecessary container
and rather pass per-type structures down to drivers directly.
Along with that, consolidate the naming of per-type structure variables
in cls_*.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the return value from -EINVAL to -EOPNOTSUPP. The rest of the
drivers have it like that, so be aligned.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As ndo_setup_tc is generic offload op for whole tc subsystem, does not
really make sense to have cls-specific args. So move them under
cls_common structurure which is embedded in all cls structs.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the type is always present, push it to be a separate argument to
ndo_setup_tc. On the way, name the type enum and use it for arg type.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
these drivers use tasklets or irq apis, but don't include interrupt.h.
Once flow cache is removed the implicit interrupt.h inclusion goes away
which will break the build.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in netdev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to change some general performance settings and to provide
some performance settings based on the device that is probed.
This includes:
- Setting the maximum read/write outstanding request limit
- Reducing the AXI interface burst length size
- Selectively setting the Tx and Rx descriptor pre-fetch threshold
- Selectively setting additional cache coherency controls
Tested and verified on all versions of the hardware.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the driver hardcodes the PBLx8 setting. Remove the need for
specifying the PBLx8 setting and automatically calculate based on the
specified PBL value. Since the PBLx8 setting applies to both Tx and Rx
use the same PBL value for both of them.
Also, the driver currently uses a bit field to set the AXI master burst
len setting. Change to the full bit field range and set the burst length
based on the specified value.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In prep for setting fine grained read and write DMA cache coherency
controls, allow specific values to be used to set the cache coherency
registers.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For IRQ affinity, set the affinity hints for the IRQs to be (initially) on
the processors corresponding to the NUMA node of the device.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to perform memory allocations on the node of the device. The
original allocation or the ring structure and Tx/Rx queues allocated all
of the memory at once and then carved it up for each channel and queue.
To best ensure that we get as much memory from the NUMA node as we can,
break the channel and ring allocations into individual allocations.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the device interrupts should function as level interrupts. For
some hardware configurations this requires setting some control bits
so that if the interrupt status has not been cleared the interrupt
should be reissued.
Additionally, when using MSI or MSI-X interrupts, run the interrupt
service routine as a tasklet so that the re-issuance of the interrupt
is handled properly.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bo Chen