Instead of handling icmp packets only up to length of icmp_packet_rr,
the code should handle any icmp length size. Therefore the length
truncating is moved to when the packet is actually sent to userspace
(this does not support lengths longer than icmp_packet_rr yet). Longer
packets are forwarded without truncating.
This patch also cleans up some parts where the icmp header struct could
be used instead of other icmp_packet(_rr) structs to make the code more
readable.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Flags covered by TT_SYNC_MASK are kept in sync among the
nodes in the network and therefore they have to be
considered while computing the global/local table CRC.
In this way a generic originator is able to understand if
its table contains the correct flags or not.
Bits from 4 to 7 in the TT flags fields are now reserved for
"synchronized" flags only.
This allows future developers to add more flags of this type
without breaking compatibility.
It's important to note that not all the remote TT flags are
synchronised. This comes from the fact that some flags are
used to inject an information once only.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
This change allows nodes to handle the TT table on a
per-VLAN basis. This is needed because nodes may have to
store only some of the global entries advertised by another
node.
In this scenario such nodes would re-create only a partial
global table and would not be able to compute a correct CRC
anymore.
This patch splits the logic and introduces one CRC per VLAN.
In this way a node fetching only some entries belonging to
some VLANs is still able to compute the needed CRCs and
still check the table correctness.
With this patch the shape of the TVLV-TT is changed too
because now a node needs to advertise all the CRCs of all
the VLANs that it is wired to.
The debug output of the local Translation Table now shows
the CRC along with each entry since there is not a common
value for the entire table anymore.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
To make the translation table code VLAN-aware, each entry
must carry the VLAN ID which it belongs to. This patch adds
such attribute to the related TT structures.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
the icmp and the icmp_rr packets share the same initial
fields since they use the same code to be processed and
forwarded.
Extract the common fields and put them into a separate
struct so that future ICMP packets can be easily added
without bloating the packet definition.
However, keep the seqno field outside of the newly created
common header because future ICMP types may require a
bigger sequence number space.
This change breaks compatibility due to fields reordering
in the ICMP headers.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Fragments arriving at their destination are buffered for later merge.
Merged packets are passed to the main receive function as had they never
been fragmented.
Fragments are forwarded without merging if the MTU of the outgoing
interface is smaller than the size of the merged packet.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Remove the existing fragmentation code before adding the new version
and delete unicast.{h,c}.
batadv_unicast_send_skb() is moved to send.c and renamed to
batadv_send_skb_unicast().
fragmentation entry in sysfs (bat_priv->fragmentation) is kept for use in
the new fragmentation code.
BATADV_UNICAST_FRAG packet type is renamed to BATADV_FRAG for use in the
new fragmentation code.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
The vis flag is not needed anymore, and since we do a compat bump we
can start with the first bit again
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
As we decreased the struct size from 26 to 24 byte, we can remove
__packed as the compiler will not add any more padding.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Reordering the packet type numbers allows us to handle unicast
packets in a general way - even if we don't know the specific packet
type, we can still forward it. There was already code handling
this for a couple of unicast packets, and this is the more
generalized version to do that.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
This is replaced by a userspace program, we don't need this
functionality to bloat the kernel.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Client flags from bit 0 to 7 are sent over the wire.
BATADV_TT_CLIENT_TEMP is a local flag and is not supposed
to be sent to the network. Therefore it has occupy a
higher bit.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
CRC32C has to be preferred to CRC16 because of its possible
HW native support and because of the reduced collision
probability. With this change the Translation Table
component now uses CRC32C to compute the local and global
table checksum.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Instead of generating roaming specific packets the TVLV unicast API is
used to send roaming information.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Instead of generating TT specific packets the TVLV unicast API is used
to send translation table data.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
The translation table meta data (version number, crc checksum, etc)
as well as the translation table diff propgated within OGMs now uses
the newly introduced tvlv infrastructure.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Create DAT container to announce DAT capabilities (if enabled).
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Prior to this patch batman-adv read the advertised uplink bandwidth
from userspace and compressed this information into a single byte
called "gateway class".
Now the download & upload bandwidth information is sent as-is. No
userspace change is necessary since the sysfs API always allowed
to specify a bandwidth.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Spyros Gasteratos <morfeas3000@gmail.com>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
The goal is to provide the infrastructure for sending, receiving and
parsing information 'containers' while preserving backward
compatibility. TVLV (based on the commonly known Type Length Value
technique) was chosen as the format for those containers. Even if a
node does not know the tvlv type of a certain container it can simply
skip the current container and proceed with the next. Past experience
has shown features evolve over time, so a 'version' field was added
right from the start to allow differentiating between feature
variants - hence the name: T(ype) V(ersion) L(ength) V(alue).
This patch introduces the basic TVLV infrastructure:
* register / unregister tvlv containers to be sent with each OGM
(on primary interfaces only)
* register / unregister callback handlers to be called upon
finding the corresponding tvlv type in a tvlv buffer
* unicast tvlv send / receive API calls
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Spyros Gasteratos <morfeas3000@gmail.com>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
With this change batman-adv is breaking compatibility with
older versions and it is moving to compat-version 15.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Add a htonl() in network_coding.c when reading the sequence number
from received ogm_packet, to avoid wrong byte ordering when comparing
with a host value. This bug was introduced in
3ed7ada3f0bbcd058567bc0a8f9729a73eba7db6 ("batman-adv: network coding -
detect coding nodes and remove these after timeout").
Change the type of coded_packet->coded_len from uint16 to __be16 to
avoid wrong assumptions about endianness in later uses. Introduced in
c3289f3650d34b60296000a629c99f2488f7c3dd ("batman-adv: network coding -
code and transmit packets if possible").
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Before adding forward-skbs to the coding buffer, the buffer is searched
for a potential coding opportunity. If one is found, the two packets are
network coded and transmitted right away. If not, the forward-skb is
added to the buffer.
Network coded packets are transmitted with information about the two
receivers and the two coded packets. The first receiver is given by the
MAC header, while the second is given in the payload/bat-header. The
second receiver uses promiscuous mode to receive the packet and check
the second destination.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The ETH_P_BATMAN ethertype is now defined kernel-wide. Use it instead
of the private BATADV_ETH_P_BATMAN define.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
All packet headers in front of an ethernet header have to be completely
divisible by 2 but not by 4 to make the payload after the ethernet header again
4 bytes boundary aligned.
A packing of 2 is necessary to avoid extra padding at the end of the struct
caused by a structure member which is larger than two bytes. Otherwise the
structure would not fulfill the previously mentioned rule to avoid the
misalignment of the payload after the ethernet header. It may also lead to
leakage of information when the padding it not initialized before sending.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
ARP messages are now parsed to make it possible to trigger special actions
depending on their types (snooping).
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The current unicast packet type does not contain the orig source address. This
patches add a new unicast packet (called UNICAST_4ADDR) which provides two new
fields: the originator source address and the subtype (the type of the data
contained in the packet payload). The former is useful to identify the node
which injected the packet into the network and the latter is useful to avoid
creating new unicast packet types in the future: a macro defining a new subtype
will be enough.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Headers which are already perfectly aligned and create a 4 byte boundary
non-ethernet header payload can have the __packed attribute removed. The
__packed attribute doesn't change the appeareance of the packet for these
headers because no extra padding is necessary to align the data members. The
compiler will also create slightly faster code for loads of multi-byte members.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
With the current TT mechanism a new client joining the network is not
immediately able to communicate with other hosts because its MAC address has not
been announced yet. This situation holds until the first OGM containing its
joining event will be spread over the mesh network.
This behaviour can be acceptable in networks where the originator interval is a
small value (e.g. 1sec) but if that value is set to an higher time (e.g. 5secs)
the client could suffer from several malfunctions like DHCP client timeouts,
etc.
This patch adds an early detection mechanism that makes nodes in the network
able to recognise "not yet announced clients" by means of the broadcast packets
they emitted on connection (e.g. ARP or DHCP request). The added client will
then be confirmed upon receiving the OGM claiming it or purged if such OGM
is not received within a fixed amount of time.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
for consistency reasons within the code and with the documentation,
we should always call it "claim" and "unclaim".
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
batman-adv doesn't follow the style for multiline comments that David S. Miller
prefers. All comments should be reformatted to follow this consistent style to
make the code slightly more readable.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
just keep it net-endian all along
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[lindner_marek@yahoo.de: fix checkpatch warnings]
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batman-adv would forward OGMs from non-besthops while replacing the the TQ
and TTL values with the values from the best hop. In certain corner cases
this leads to a temporary routing loop.
This patch changes this behavior: Only packets from best next hops are
forwarded - TQ and TTL values won't be replaced anymore. However, the protocol
needs to rebroadcast OGMs from single hop neighbors regardless of whether or
not they are the best hop. To handle this case a new flag is introduced to
alert neighboring nodes about the forwarded OGM that is not from my best
next hop. It is to be discarded by all nodes except for the one originating
the OGM.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Daniele Furlan <daniele.furlan@gmail.com>
Tested-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
The coming protocol changes also will have a part called "OGM". That
makes it necessary to introduce a distinction in the code base.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Using BATMAN_OGM_LEN leaves one with the impression that this is
the full packet size which is not the case. Therefore the variable
is renamed.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
This second version of the bridge loop avoidance for batman-adv
avoids loops between the mesh and a backbone (usually a LAN).
By connecting multiple batman-adv mesh nodes to the same ethernet
segment a loop can be created when the soft-interface is bridged
into that ethernet segment. A simple visualization of the loop
involving the most common case - a LAN as ethernet segment:
node1 <-- LAN --> node2
| |
wifi <-- mesh --> wifi
Packets from the LAN (e.g. ARP broadcasts) will circle forever from
node1 or node2 over the mesh back into the LAN.
With this patch, batman recognizes backbone gateways, nodes which are
part of the mesh and backbone/LAN at the same time. Each backbone
gateway "claims" clients from within the mesh to handle them
exclusively. By restricting that only responsible backbone gateways
may handle their claimed clients traffic, loops are effectively
avoided.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
In packet.h the numeric constant 6 is used instead of the more portable ETH_ALEN
define. This patch substitute any hardcoded value with such define.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Acked-by: Sven Eckelmann <sven@narfation.org>
All batman-adv packets have a common 3 byte header. It can be used to share
some code between different code paths, but it was never explicit stated that
this header has to be always the same for all packets. Therefore, new code
changes always have the problem that they may accidently introduce regressions
by moving some elements around.
A new structure is introduced that contains the common header and makes it
easier visible that these 3 bytes have to be the same for all on-wire packets.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
The follow-up routing code changes are going to introduce additional
routing packet types which make this distinction necessary.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Clients connected through a 802.11 device are now marked with the
TT_CLIENT_WIFI flag. This flag is also advertised with the tt
announcement.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
To keep transtable consistency among all the nodes, an originator must
not send not yet announced clients within a full table TT_RESPONSE.
Instead, deleted client have to be kept in the table in order to be sent
within an immediate TT_RESPONSE. In this way all the nodes in the
network will always provide the same response for the same request.
All the modification are committed at the next ttvn increment event.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Simon Wunderlich