An RC device is does not need to be called 'RC for'. Simply the name
will suffice.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The calculation of the Signal Free Time in the framework was not
correct. If a message was received, then the next transmit should be
considered a New Initiator and use a shorter SFT value.
This was not done with the result that if both sides where continually
sending messages, they both could use the same SFT value and one side
could deny the other side access to the bus.
Note that this fix does not take the corner case into account where
a receive is in progress when you call adap_transmit.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.18 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Several CEC functions are actually specific for use with receivers,
i.e. they should be part of the V4L2 subsystem, not CEC.
These functions deal with validating and modifying EDIDs for (HDMI)
receivers, and they do not actually have anything to do with the CEC
subsystem and whether or not CEC is enabled. The problem was that if
the CEC_CORE config option was not set, then these functions would
become stubs, but that's not right: they should always be valid.
So replace the cec_ prefix by v4l2_ and move them to v4l2-dv-timings.c.
Update all drivers that call these accordingly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <stable@vger.kernel.org> # for v4.17 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This function is needed by both V4L2 and CEC, so move this to
cec.h as a static inline since there are no obvious shared
modules between the two subsystems.
This patch, together with the following ones, fixes a
dependency bug: if CEC_CORE is disabled, then building adv7604
(and other HDMI receivers) will fail because an essential
function is now stubbed out.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.17 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for the new 5V CEC events
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It turns out that the struct cec_fh event buffer size of 64 events
(64 for CEC_EVENT_PIN_CEC_LOW and 64 for _HIGH) is too small. It's
about 160 ms worth of events and if the Raspberry Pi is busy, then it
might take too long for the application to be scheduled so that it can
drain the pending events. Increase these buffers to 800 events which
is at least 2 seconds worth of events.
There is also a FIFO in between the interrupt and the cec-pin thread.
The thread passes the events on to the CEC core. It is important that
should this FIFO fill up the cec core will be informed that events
have been lost so this can be communicated to the user by setting
CEC_EVENT_FL_DROPPED_EVENTS.
It is very hard to debug CEC problems if events were lost without
informing the user of that fact.
If events were dropped due to the FIFO filling up, then the debugfs
status file will let you know how many events were dropped.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add two new ops (error_inj_show and error_inj_parse_line) to support
error injection functionality for CEC adapters. If both are present,
then the core will add a new error-inj debugfs file that can be used
to see the current error injection commands and to set error injection
commands.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Replace the old license information with the corresponding SPDX
license for those headers that I authored.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
CEC autorepeat is different than other protocols. Autorepeat is triggered
by the first repeated user control pressed CEC message, rather than a
fixed REP_DELAY.
This change also does away with the KEY_UP event directly after the first
KEY_DOWN event, which was used to stop autorepeat from starting.
See commit a9a249a2c9 ("media: cec: fix remote control passthrough")
for the original change.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When the device is being unregistered disable the hardware, don't wait
until cec_delete_adapter is called as the hardware may have disappeared by
then. This would be the case for hotplugable devices.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Bård Eirik Winther <bwinther@cisco.com>
Tested-by: Bård Eirik Winther <bwinther@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some devices can monitor the CEC pin using an interrupt, but you
only want to enable the interrupt if you actually switch to pin
monitoring mode.
So add a new op that is called when pin monitoring needs to be
switched on or off.
Also fix a small bug where the initial CEC pin event was sent
again when calling S_MODE twice with the same CEC_MODE_MONITOR_PIN
mode.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make sure these values are set to avoid 'uninitialized variable'
warnings. Hasn't happened yet, but better safe than sorry.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for two new low-level events: PIN_HPD_LOW and PIN_HPD_HIGH.
This is specifically meant for use with the upcoming cec-gpio driver
and makes it possible to trace when the HPD pin changes. Some HDMI
sinks do strange things with the HPD and this makes it easy to debug
this.
Note that this also moves the initialization of a devnode mutex and
list to the allocate_adapter function: if the HPD is high, then as
soon as the HPD interrupt is created an interrupt occurs and
cec_queue_pin_hpd_event() is called which requires that the devnode
mutex and list are initialized.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The current CEC pin value (0 or 1) was part of the cec_pin struct,
but that assumes that CEC pin monitoring can only be used with
a driver that uses the low-level CEC pin framework.
But hardware that has both a high-level API and can monitor the
CEC pin at low-level at the same time does not need to depend on
the cec pin framework.
To support such devices remove the cur_value field from struct cec_pin
and add a cec_pin_is_high field to cec_adapter. This also makes it
possible to drop the '#ifdef CONFIG_CEC_PIN' in cec-api.c.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The 'Press and Hold' operation was not correctly implemented, in
particular the requirement that the repeat doesn't start until
the second identical keypress arrives. The REP_DELAY value also
had to be adjusted (see the comment in the code) to achieve the
desired behavior.
The 'enabled_protocols' field was also never set, fix that too. Since
CEC is a fixed protocol the driver has to set this field.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When an ir-spi is registered, you get this message.
rc rc0: Unspecified device as /devices/platform/soc/3f215080.spi/spi_master/spi32766/spi32766.128/rc/rc0
"Unspecified device" refers to input_name, which makes no sense for IR
TX only devices. So, rename to device_name.
Also make driver_name const char* so that no casts are needed anywhere.
Now ir-spi reports:
rc rc0: IR SPI as /devices/platform/soc/3f215080.spi/spi_master/spi32766/spi32766.128/rc/rc0
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The CEC_EVENT_PIN_LOW/HIGH defines and the cec_queue_pin_event() function
did not specify that these were about CEC pin events.
Since in the future there will also be HPD pin events it is wise to rename
the event defines and function to CEC_EVENT_PIN_CEC_LOW/HIGH and
cec_queue_pin_cec_event() now before these become part of the ABI.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The CEC_CAP_LOG_ADDRS, CEC_CAP_TRANSMIT, CEC_CAP_PASSTHROUGH and
CEC_CAP_RC capabilities are normally always present.
Add a CEC_CAP_DEFAULTS define that ORs these four caps to simplify
drivers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The cec_register_cec_notifier function was in media/cec.h, but it
has to be in cec-notifier.h.
While we are at it, also document it and add a stub function for when
the notifier is disabled or the CEC core code is unreachable.
Based on an earlier patch from Jose Abreu <Jose.Abreu@synopsys.com>.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for CEC hardware that relies on low-level pin polling or
GPIO interrupts.
One example is the Allwinner SoC. But any GPIO-based CEC implementation can
use this as well.
A GPIO implementation is very suitable as well for debugging: it can use
interrupts to detect state changes and report it. Userspace can then verify
if the bus traffic is correct. This also makes error injection possible.
The disadvantage is that it is hard to get the timings right since linux
isn't a hard realtime system.
In general on an idle system it works quite well, but under load the timer
will miss its mark every so often.
The debugfs file /sys/kernel/debug/cec/cecX/status gives some statistics
with respect to the timer overruns.
When the adapter is unconfigured and the low-level driver supports
interrupts, then the interrupt will be used to detect changes. This should
be quite accurate. But when the adapter is configured a hrtimer has to be
used.
The hrtimer implements a state machine where for each state the code will
read the bus or drive the bus and go on to the next state. It will re-arm
the timer with a delay based on the next state.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for the new MONITOR_PIN mode.
Add the cec_pin_event function that the CEC pin code will call to queue pin
change events.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Event handling was always fairly simplistic since there were only
two events. With the addition of pin events this needed to be redesigned.
The state_change and lost_msgs events are now core events with the
guarantee that the last state is always available. The new pin events
are a queue of events (up to 64 for each event) and the oldest event
will be dropped if the application cannot keep up. Lost events are
marked with a new event flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is needed for CEC adapters that allocate resources that have
to be freed before the cec_adapter is deleted.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently the transmit_(attempt_)done and received_msg functions set
the timestamp themselves. For the upcoming low-level pin API we need
to pass this as an argument instead. So make _ts variants that allow
the caller to specify the timestamp.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Kernel logging messes up the upcoming low-level CEC monitoring support
which is very time-sensitive. So change the debug level of this message
but keep a counter that is shown in the debugfs status log.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
-----BEGIN PGP SIGNATURE-----
iQEbBAABAgAGBQJZR92EAAoJEHm+PkMAQRiGT1oH+KW2FLrRaYxtut+KyGA6l7tc
R/hFx1n9BibkjXeqD+y6/4SjRTe6/pT8Zkihv3/19eZ5algUWeQa0Hm+/455sl58
IdIXx/pzuCO3kqR3//fP9ZFD657GNDsuQ0fYnZESItFwiWQtO1TNfZD6KQjkqBdI
L3MVhDUVBZA2ZtPwC4ERei5/sToV9woykKoJ/A3+OkWjgX6w4SBimqgkSEFk4uE8
xS0pycyDZci93rJlECi1UueewdODTKSmhwdC80qvGEiYXzsC6UFtaF0Fj66XO1AL
UMjxqI/gkm5ZuCIjRsmPmJjgL5q1RT6UX/qtw9yn71XTmcgMiPW2/DF/v/OaTg==
=XbW2
-----END PGP SIGNATURE-----
Merge tag 'v4.12-rc6' into patchwork
Linux 4.12-rc6
* tag 'v4.12-rc6': (813 commits)
Linux 4.12-rc6
mm: larger stack guard gap, between vmas
virtio_balloon: disable VIOMMU support
mm: correct the comment when reclaimed pages exceed the scanned pages
userfaultfd: shmem: handle coredumping in handle_userfault()
mm: numa: avoid waiting on freed migrated pages
swap: cond_resched in swap_cgroup_prepare()
mm/memory-failure.c: use compound_head() flags for huge pages
perf unwind: Report module before querying isactivation in dwfl unwind
fs: pass on flags in compat_writev
objtool: Add fortify_panic as __noreturn function
powerpc/debug: Add missing warn flag to WARN_ON's non-builtin path
USB: gadgetfs, dummy-hcd, net2280: fix locking for callbacks
drm: mxsfb_crtc: Reset the eLCDIF controller
drm/mgag200: Fix to always set HiPri for G200e4 V2
i2c: ismt: fix wrong device address when unmap the data buffer
i2c: rcar: use correct length when unmapping DMA
powerpc/xive: Fix offset for store EOI MMIOs
drm/tegra: Correct idr_alloc() minimum id
drm/tegra: Fix lockup on a use of staging API
...
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a new capability CEC_CAP_NEEDS_HPD. If this capability is set
then the hardware can only use CEC if the HDMI Hotplug Detect pin
is high. Such hardware cannot handle the corner case in the CEC specification
where it is possible to transmit messages even if no hotplug signal is
present (needed for some displays that turn off the HPD when in standby,
but still have CEC enabled).
Typically hardware that needs this capability have the HPD wired to the CEC
block, often to a 'power' or 'active' pin.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A simpler variant of cec_transmit_done to be used where the HW does
just a single attempt at a transmit. So if the status indicates an
error, then the corresponding error count will always be 1 and this
function figures that out based on the status argument.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Simplifies setting the physical address to CEC_PHYS_ADDR_INVALID.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This function simplifies the integration of CEC in DRM drivers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix messages like this:
adv7842.c:(.text+0x2edadd): undefined reference to `cec_unregister_adapter'
when CEC_CORE=m but the driver including media/cec.h is built-in. In that case
the static inlines provided in media/cec.h should be used by that driver.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This config option is strictly speaking independent of the
media subsystem since it can be used by drm as well.
Besides, it looks odd when drivers select CEC_CORE and
MEDIA_CEC_NOTIFIER, that's inconsistent naming.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Drop the separate cec-edid.h header and merge it into cec.h.
There was really no need to have a separate header for this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The Kconfig options for the CEC subsystem were a bit messy. In
addition there were two cec sources (cec-edid.c and cec-notifier.c)
that were outside of the media/cec directory, which was weird.
Move those sources to media/cec as well.
The cec-edid and cec-notifier functionality is now part of the cec
module and these are no longer separate modules.
Also remove the MEDIA_CEC_EDID config option and include it with the
main CEC config option (which defined CEC_EDID anyway).
Added static inlines to cec-edid.h for dummy functions when CEC_CORE
isn't defined.
CEC drivers should now depend on CEC_CORE.
CEC drivers that need the cec-notifier functionality must explicitly
select CEC_NOTIFIER.
The s5p-cec and stih-cec drivers depended on VIDEO_DEV instead of
CEC_CORE, fix that as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Support the CEC notifier framework, simplifying drivers that
depend on this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a helper function to get driver private data from CEC
adapter. This helps the readability a little bit and allows
to change the 'priv' field name to something else without
needing to touch all drivers.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The cec_allocate_adapter function doesn't need the parent device, only the
cec_register_adapter function needs it.
Drop the cec_devnode parent field, since devnode.dev.parent can be used
instead.
This change makes the framework consistent with other frameworks where the
parent device is not used until the device is registered.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The last open issues have been addressed, so it is time to move
this out of staging and into the mainline and to move the public
cec headers to include/uapi/linux.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This lock will be used to protect more than just the fhs list.
So rename it to just 'lock'.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The size of the transmit queue was unlimited, which meant that
in non-blocking mode you could flood the CEC adapter with messages
to be transmitted.
Limit this to 18 messages.
Also print the number of pending transmits and the timeout value
in the status debugfs file.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The added HDMI CEC framework provides a generic kernel interface for
HDMI CEC devices.
Note that the CEC framework is added to staging/media and that the
cec.h and cec-funcs.h headers are not exported yet. While the kABI
is mature, I would prefer to allow the uABI some more time before
it is mainlined in case it needs more tweaks.
This adds the cec-core.c, media/cec.h and cec-priv.h sources.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[k.debski@samsung.com: Merged CEC Updates commit by Hans Verkuil]
[k.debski@samsung.com: Merged Update author commit by Hans Verkuil]
[k.debski@samsung.com: code cleanup and fixes]
[k.debski@samsung.com: add missing CEC commands to match spec]
[k.debski@samsung.com: add RC framework support]
[k.debski@samsung.com: move and edit documentation]
[k.debski@samsung.com: add vendor id reporting]
[k.debski@samsung.com: reorder of API structs and add reserved fields]
[k.debski@samsung.com: fix handling of events and fix 32/64bit timespec problem]
[k.debski@samsung.com: add sequence number handling]
[k.debski@samsung.com: add passthrough mode]
[k.debski@samsung.com: fix CEC defines, add missing CEC 2.0 commands]
Signed-off-by: Kamil Debski <kamil@wypas.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Sean Young