Add iommus properties to the device tree nodes for the two display
controllers found on Tegra30. This will allow the display controllers to
map physically non-contiguous buffers to I/O virtual contiguous address
spaces so that they can be used for scan-out.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the memory controller and wire up the interrupt that is used to
report errors. Provide a reference to the memory controller clock and
mark the device as being an IOMMU by adding an #iommu-cells property.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the device tree node for the memory controller found on Tegra114
SoCs. The memory controller integrates an IOMMU (called SMMU) as well as
various knobs to tweak memory accesses by the various clients.
The old IOMMU device tree node is collapsed into the memory controller
node to more accurately describe the hardware. While this change is
incompatible, the IOMMU driver has never had any users so the change is
not going to cause any breakage.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Collapses the old memory-controller and IOMMU device tree nodes into a
single node to more accurately describe the hardware.
While this is an incompatible change there are no users of the IOMMU on
Tegra, even though a driver has existed for some time.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch adds the APB_MISC_GP_MIPI_PAD_CTRL_0 as a pin-control bank on
Tegra124 so the new MIPI pad control group can be muxed between CSI and
DSI_B.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
vsys is the core always-on supply of the Marsboard.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
IRQ support for Broadcom's bus-axi driver bcma was merged into John
Linville's wireless tree and will show up in 3.19. This patch makes use
of this feature in the DTS file for the the BCM5301X SoCs. I left the
PCIe controller out, because this still needs some discussion.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add a DTS describing the Digilent ZYBO board. Similar to ZED but with
a 50MHz crystal instead of 33MHz.
Acked-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The fact that all supported boards use the same 33MHz crystal is a
co-incidence. The Zynq PS support a range of crystal freqs so the
hardcoded setting should be removed from the dtsi. Re-implement it
on the board level.
This prepares support for Zynq boards with different crystal
frequencies (e.g. the Digilent ZYBO).
Acked-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The SDMMC, SDIO and EMMC controllers use an external FIFO whose size is 256x32bit.
This patch set the corresponding fifo-depth properties for both RK3066 and RK3188.
Signed-off-by: Julien CHAUVEAU <julien.chauveau@neo-technologies.fr>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The leds-gpio driver recently switched to the device property API. The device_node
name is no longer retrieved if the "label" devicetree property is not found.
In this case the driver tries to create entries with (null) name in
/sys/class/leds, which is wrong and generates backtrace as several gpio_leds have
the same name. Also renamed subnode "yellow" to "blue" to match the last
schematics updates.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The suspend/resume sequence on Armada XP needs to modify a number of
registers in the SDRAM controller. Therefore, this commit updates the
Armada XP Device Tree description to include the SDRAM controller
Device Tree node.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1416585613-2113-17-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
In order to support suspend/resume on Armada XP, an additional set of
registers need to be described at the MBus controller level. This
commit therefore adjusts the Device Tree of the Armada 370/XP SoC to
include those registers in the MBus controller description;
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1416585613-2113-16-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit improves the Armada XP GP Device Tree description to
describe the 3 GPIOs that are used to connect the SoC to the PIC
micro-controller that we talk to shutdown the SoC when entering
suspend to RAM.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1416585613-2113-15-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The most important part is adding the axi bus to the SoC dtsi file,
this is the main bus on the SoC.
These patches were all send to the arm list and I haven't got any
negative responses.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=oMPU
-----END PGP SIGNATURE-----
Merge tag 'bcm5301x-dt-2014-11-27' of https://github.com/hauke/linux into next/dt
Pull "ARM: BCM5301X: Add some more devices to device tree" from Hauke Mehrtens:
The most important part is adding the axi bus to the SoC dtsi file,
this is the main bus on the SoC.
These patches were all send to the arm list and I haven't got any
negative responses.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* tag 'bcm5301x-dt-2014-11-27' of https://github.com/hauke/linux:
ARM: BCM5301X: Add LEDs for Netgear R6250 V1
ARM: BCM5301X: Add Broadcom's bus-axi to the DTS file
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Armada 375
- Add PHY and USB cluster controller support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=j1MN
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-usb-phy-3.19-3' of git://git.infradead.org/linux-mvebu into next/dt2
Pull "mvebu DT changes for v3.19 (round 3)" from Jason Cooper:
- Armada 375
- Add PHY and USB cluster controller support
* tag 'mvebu-dt-usb-phy-3.19-3' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: add PHY support to the dts for the USB controllers on Armada 375
ARM: mvebu: add Device Tree description of USB cluster controller on Armada 375
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUX/DqAAoJEHm+PkMAQRiGLtQH/iAt3fRHlYDXjaJian/KG1Cb
wVP0I+HWZmvVmmd0PzyaxCZLgRNwdmmYHEH4QLy2JwZ3jZfFHlxhy+hDWCgz+67t
bIzkLs0Pf1T4kJ2+r8qW2kBEz9PWJHGTQw7NTqZ++Ts3rPptBA6Fg4mEJ6fQigXy
qRIY68DpipUkXV9BWBWijnTmrvP5tt7JtPzBr4DC8frMjvWct8+XwYhc2k2tEv2j
LwLYb1OW6PUpPv2BQBfWjqqH77vYNQVhJwuwGcDe2YZdI0UFkDheL24+RbbPcZ4f
OnrLjJSSgzv6lBWkAaXZK7/WJ/JZbXxEqHzWZQ3xXoQov97bm7lEYJqqi5gDasQ=
=6Qpa
-----END PGP SIGNATURE-----
Merge tag 'v3.18-rc4' into next/dt2
Linux 3.18-rc4 is a dependency for the phy-dt-header branch that
is needed for the final mvebu DT changes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- mvebu
- Use simple-card audio on Armada 370 DB
- Add DSA node for Armada 370 DB
- Add SDHCI to Armada 38x
- Armada 370/XP rework to support new Synology boards
- Add Synology DS213j and DS414
- Various pinctrl and uart and alias fixes to help bootloaders
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=F5lu
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-3.19-2' of git://git.infradead.org/linux-mvebu into next/dt
Pull "mvebu DT changes for v3.19 (round 2)" from Jason Cooper:
- mvebu
- Use simple-card audio on Armada 370 DB
- Add DSA node for Armada 370 DB
- Add SDHCI to Armada 38x
- Armada 370/XP rework to support new Synology boards
- Add Synology DS213j and DS414
- Various pinctrl and uart and alias fixes to help bootloaders
* tag 'mvebu-dt-3.19-2' of git://git.infradead.org/linux-mvebu:
arm: mvebu: normalize pinctrl entries for Armada SoCs
arm: mvebu: fix wrongly named DS414 pinctrl entries
arm: mvebu: add .dts file for Synology DS414
arm: mvebu: add .dts file for Synology DS213j
arm: mvebu: define and use common Armada XP SPI pinctrl setting
arm: mvebu: define and use common Armada XP UART2/3 pinctrl settings
arm: mvebu: define and use common Armada 370 UART pinctrl settings
arm: mvebu: define and use common Armada 370 SPI pinctrl settings
arm: mvebu: move Armada 370/XP pinctrl node definition armada-370-xp.dtsi
arm: mvebu: use recently introduced uart label for stdout-path
arm: mvebu: add uartX labels for Armada SoC serial nodes
arm: mvebu: fix vendor prefix typo in kirkwood-synology.dtsi
ARM: mvebu: fix ordering in Armada 370 .dtsi
ARM: mvebu: adjust ethernet aliases according to U-Boot requirements for A38x
ARM: mvebu: remove clock-frequency from Armada 38x SDHCI Device Tree node
ARM: mvebu: enable no-1-8-v flag for Armada 385 DB SDHCI interface
mvebu: 370 RD: Add support for the switch
ARM: mvebu: use simple-card DT binding for audio on Armada 370 DB
ARM: mvebu: remove conflicting muxing on Armada 370 DB
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This enables the simple framebuffer on all the supported Allwinner SoCs (but
the A80). That allows to have at last a video display usable by using the
framebuffer the firmware might have set up.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Rgt0
-----END PGP SIGNATURE-----
Merge tag 'sunxi-simplefb-for-3.19' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Pull "Allwinner simple frambuffer support" from Maxime Ripard:
This enables the simple framebuffer on all the supported Allwinner SoCs (but
the A80). That allows to have at last a video display usable by using the
framebuffer the firmware might have set up.
* tag 'sunxi-simplefb-for-3.19' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (55 commits)
ARM: dts: sunxi: Update simplefb nodes so that u-boot can find them
ARM: dts: sunxi: Add de_be0 clk parent pll to simplefb node
ARM: dts: sun7i: Add simplefb node
ARM: dts: sun6i: Add simplefb node
ARM: dts: sun5i: Add simplefb node
ARM: dts: sun4i: Add simplefb node
ARM: dts: sun6i: Add ethernet support to M9 board
ARM: sun6i: DT: Add PLL6 multiple outputs
ARM: dts: sun6i: Add support for the status led
ARM: dts: sun6i: Add EHCI support for the M9 board
ARM: dts: sunxi: Add regulator-boot-on property to ahci-5v regulator
ARM: dts: sun7i: Cubietruck: add power supply regulator for USB OTG VBUS
ARM: dts: sun7i: Cubietruck: override regulator pin
ARM: sun7i: dtsi: add support for usbphy0
ARM: dtsi: sunxi: add common VBUS regulator
ARM: dts: sunxi: Banana Pi: increase startup-delay for the GMAC PHY regulator
ARM: sun5i: olinuxino: Relicense the device tree under GPLv2/X11
ARM: sun4i: cubieboard: Relicense the device tree under GPLv2/X11
ARM: sun7i: pcduino3: Relicense the device tree under GPLv2/X11
ARM: sun4i: pcduino: Relicense the device tree under GPLv2/X11
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Device additions for board vf610-colibri, pwm, backlight, I2C, RTC,
ADC etc.
- Update i.MX6 phyFLEX board to include PCIe, CAN and audio support
- Improve SSI clocks description for i.MX5 platforms
- Add ENET2 support for imx6sx-sdb board
- Add device tree source for LS1021A SoC, board QDS and TWR
- Enable cpufreq support for i.MX53
- Enable VPU device support for i.MX6QDL
- Enable poweroff support for i.MX6 SoCs
- Add support for TBS2910 Matrix ARM mini PC which is built on i.MX6Q
- Create generic base device trees for Vybrid and add support for
Colibri VF50
Note: the change set is built on top of imx-soc-3.19 to resolve the
dependency that "ARM: dts: imx53: add cpufreq-dt support" uses the
clock define IMX5_CLK_ARM that is added by "ARM: imx53: clk: add ARM
clock".
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUcZicAAoJEFBXWFqHsHzO0ooH/ie5r7JDjklD6IlAxD9UyDyp
RQSF/8VYTc1EhECI5D/xmHARnUM5AxfMBQzFyavz/0hkGp22xJtBgp5ZlYtWwyAF
qpLI031/5hn+37NyMxdcd6nU55e7GJw4loBXTZ5pNSRdP+ubsUVccfUdQ1K5hPA6
KeS5vqaX26c5P2R+tkx2pfRLmCrSWNKNIpIbZzenlu2dS7U77ex1AO2W+ToDTgQ3
asVIMD/7oQ4soEGZfSQdzHCftQ2OdVGlybFoMCkW5xrzRVfucbSN2BbLpEM5Z117
/DZpfAmHlT4NrGz/BBzpK6l3AWFmXLmCP/dFvvfzKM3uWgr/zlVF8ChW/xgCc+g=
=FnNq
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Pull "The i.MX device tree changes for 3.19" from Shawn Guo:
- Device additions for board vf610-colibri, pwm, backlight, I2C, RTC,
ADC etc.
- Update i.MX6 phyFLEX board to include PCIe, CAN and audio support
- Improve SSI clocks description for i.MX5 platforms
- Add ENET2 support for imx6sx-sdb board
- Add device tree source for LS1021A SoC, board QDS and TWR
- Enable cpufreq support for i.MX53
- Enable VPU device support for i.MX6QDL
- Enable poweroff support for i.MX6 SoCs
- Add support for TBS2910 Matrix ARM mini PC which is built on i.MX6Q
- Create generic base device trees for Vybrid and add support for
Colibri VF50
Note: the change set is built on top of imx-soc-3.19 to resolve the
dependency that "ARM: dts: imx53: add cpufreq-dt support" uses the
clock define IMX5_CLK_ARM that is added by "ARM: imx53: clk: add ARM
clock".
* tag 'imx-dt-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (51 commits)
ARM: dts: imx6q-tbs2910: Enable snvs-poweroff
ARM: dts: imx6: add pm_power_off support for i.mx6 chips
ARM: dts: vf-colibri: add USB regulators
ARM: dts: imx6: phyFLEX: Add CAN support
ARM: dts: imx6: phyFLEX: Add PCIe
ARM: dts: imx6: phyFLEX: Set correct interrupt for pmic
ARM: dts: imx6: phyFLEX: Enable gpmi in module file
ARM: dts: imx6: phyFLEX: set nodes in alphabetical order
ARM: dts: vf-colibri-eval-v3.dts: Enable ST-M41T0M6 RTC
ARM: dts: vf-colibri: Add I2C support
ARM: dts: imx6qdl: Enable CODA960 VPU
ARM: dts: imx6q-tbs2910: Remove unneeded 'fsl,mode' property
ARM: dts: vf610: enable USB misc/phy nodes where necessary
ARM: dts: vf610: use new GPIO support
ARM: dts: pbab01: enable I2S audio on phyFLEX-i.MX6 boards
ARM: dts: pbab01: move i2c pins and frequency configuration into pfla02
ARM: dts: vf500-colibri: add Colibri VF50 support
ARM: dts: vf610: create generic base device trees
ARM: dts: vf610: assign oscillator to clock module
dt-bindings: arm: add Freescale LS1021A SoC device tree binding
...
Signed-off-by; Arnd Bergmann <arnd@arndb.de>
- Clean up reset handler for DT machines, since reset has been handled
in watchdog driver
- Remove unneeded .map_io hook for a couple of i.MX6 machines
- A few small i.MX6 device tree source cleanups
- Some random iomuxc and pllv3 code cleanup
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUcYNdAAoJEFBXWFqHsHzOhJUH/i2Ssq8yJb7rSkjGBvytZQhW
b9JdPrGBZmeh0247brB5FB4EzDg3p8o+/v7tNPofP6RwbJXCsWQaLwNRNwTdL+mv
KoKboCnIBB9OdGQw7IWZ2tKjmP4msmXbTbX/+Rf/f6sukd9VL/lxK7An3iVNmlJw
gD2y9Ryul0xBkxajvM6JduBwpTVnjCSzpOWGB+GjpUiMPqm5li1qmyKaQc1Vh7Dm
fbr0ZWgj+NaJkuOAQ5rL4HtJs/bzoLjTkTAnehoTrt9bVWOySy7LQVG2CsHmT2eD
2jzjVUC7NcBHbubs9HhK5kCnASE2Lr7u3JnSNpjAxWpHM9e0tYo4+PiW1pZX11k=
=+FHh
-----END PGP SIGNATURE-----
Merge tag 'imx-cleanup-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/cleanup
Pull "The i.MX cleanup for 3.19" from Shawn Guo:
- Clean up reset handler for DT machines, since reset has been handled
in watchdog driver
- Remove unneeded .map_io hook for a couple of i.MX6 machines
- A few small i.MX6 device tree source cleanups
- Some random iomuxc and pllv3 code cleanup
* tag 'imx-cleanup-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx: Remove unneeded .map_io initialization
ARM: dts: imx6qdl-sabresd: Fix the microphone route
ARM: imx: refactor mxc_iomux_mode()
ARM: imx: simplify clk_pllv3_prepare()
ARM: imx6q: drop unnecessary semicolon
ARM: imx: clean up machine mxc_arch_reset_init_dt reset init
ARM: dts: imx6qdl-rex: Remove unneeded 'fsl,mode' property
ARM: dts: imx6qdl-gw5x: Remove unneeded 'fsl,mode' property
ARM: dts: imx6qdl-sabresd: Use IMX6QDL_CLK_CKO define
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
SoC related changes for omaps including hwmod clean-up for
DSS, and hwmod data for more UARTs and ADC. Also few defconfig
changes to enable devices found on am335x and am437x.
[arnd: I removed the defconfig changes from the branch in order
to cherry-pick them onto the next/defconfig branch, but I did
not change the other commits]
* commit '29c4ce17bcad':
ARM: dts: cm-t3x30: add keypad support
ARM: OMAP2+: hwmod: AM43x: add hwmod support for ADC on AM43xx
ARM: DRA7: hwmod data: Add missing UART hwmod data
ARM: dts: omap4.dtsi: remove dss_fck
ARM: OMAP4: fix RFBI iclk
ARM: OMAP4: hwmod: use MODULEMODE properly
ARM: OMAP4: hwmod: set DSS submodule parent hwmods
ARM: OMAP5: hwmod: set DSS submodule parent hwmods
ARM: OMAP2+: hwmod: add parent_hwmod support
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
run again, until the patches for using the physical architected
timers got accepted.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJUcK60AAoJEPOmecmc0R2BPqYH/202nLDZaBuY3ZaXIoRUNZx4
s5oPQWmJ9xSW4K93tnAtrQ3YP9NE4SrSSAKIszeY7sNI0XapdFrT8ARinh3bA8Ir
cCr0iXMGHwpWF9K9nfYM8z+fNIwVOa2KktbmZi9tgOvxfOFkadRXoBj6gdxwN8oO
2UTgbB7iD2F0FRTj+kmrxTML+vkW8LyladQIoyyeCwoFCkUYoPerLpuwvnPEujoO
aN3eot9w7uqP28NwsD9nC5Ns+mzICF9ts3IRCyv1zoGkXpA+7meHvNvtrOW2v3JJ
xdUh8bvCwSMrb0jh07PDfSFMkOZlfNIl8eXUZrxx66ss8VDMCXwVaxLS7llxdCk=
=gBaE
-----END PGP SIGNATURE-----
Merge tag 'v3.19-rockchip-dts3' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Pull "temporarily disable rk3288-smp" from Heiko Stuebner:
Disable smp again on rk3288 temporarily to make Olof's boottest
run again, until the patches for using the physical architected
timers got accepted.
* tag 'v3.19-rockchip-dts3' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: temporarily disable smp on rk3288
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This has been successfully tested on Netgear R6250 and two other
development (unnamed) devices, all of them BCM4708 based.
We also got a possitive feedback from R7000 (BCM4709) tester.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
- explicitly set dr_mode on exynos5250-snow
this is required when kernel is built with USB gadget support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=R/UY
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Pull "Samsung fixes for v3.18" from Kukjin Kim:
- explicitly set dr_mode on exynos5250-snow
this is required when kernel is built with USB gadget support.
* tag 'samsung-fixes-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Explicitly set dr_mode on exynos5250-snow
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds syscon based phandle to i2c device nodes of exynos5250
and exynos5420. These phandles will be used to save restore i2c sysreg
configuration register during s2r from i2c driver.
CC: Rob Herring <robh+dt@kernel.org>
CC: Randy Dunlap <rdunlap@infradead.org>
CC: Russell King <linux@arm.linux.org.uk>
CC: devicetree@vger.kernel.org
CC: linux-doc@vger.kernel.org
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch removes unused dt node of command line from Exynos3250-based
Rinato board because kernel use the command line from bootloader.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds new board dts file to support Samsung Monk board which
is based on Exynos3250 SoC and has different H/W configuration from
Rinato.
This dts file support following features:
- eMMC
- Main PMIC (Samsung S2MPS14)
- Interface PMIC (Maxim MAX77836, MUIC, fuel-gauge, charger)
- RTC of Exynos3250
- ADC of Exynos3250 with NTC thermistor
- I2S of Exynos3250
- TMU of Exynos3250
- Secure firmware for Exynos3250 secondary cpu boot
- Serial ports of Exynos3250
- gpio-key for power key
Signed-off-by: Youngjun Cho <yj44.cho@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This adds a node for the IR remote control receiver to the Amlogic
Meson DTS.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are currently 2 differents naming conventions used between the
existing Armada SoC DT files for pinctrl entries (*_pin(s): *-pin(s)
and pmx_*: pmx-*) with a vast majority of files using the former:
$ grep _pin arch/arm/boot/dts/armada-*.dts* | wc -l
155
$ grep pmx arch/arm/boot/dts/armada-*.dts* | wc -l
13
In fact, only some Armada XP files are using the second variant.
This patch normalizes those files (mainly ge0/1 entries) to use
the first variant.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/00114c3169e1d93259ff4150ed46ee36eae16b1e.1416670812.git.arno@natisbad.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
While renaming pinctrl entries during reviews of Synology DS414 support
series, I missed three entries, as reported by Ben. This patch fixes
those.
Reported-by: Ben Peddell <klightspeed@killerwolves.net>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/608e4fd6e06e9c5289a84b9c38e81b2456dbcd79.1416670812.git.arno@natisbad.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
On Armada 375, the USB cluster allows to control the cluster composed
of the USB2 and USB3 host controllers.
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1415879269-29711-6-git-send-email-gregory.clement@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
PHY driver and its associated Device Tree node(s)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WOgc
-----END PGP SIGNATURE-----
Merge tag 'tags/phy-dt-header' into mvebu/dt-usb_phy
shared header file which will be referenced from both
PHY driver and its associated Device Tree node(s)
This time, a very pull request with 216 non-merge
commits. Most of the commits contained here are
sparse or coccinelle fixes ranging from missing
'static' to returning 0 in case of errors.
More importantly, we have the removal the now
unnecessary 'driver' argument to ->udc_stop().
DWC2 learned about Dual-Role builds. Users of
this IP can now have a single driver built for
host and device roles.
DWC3 got support for two new HW platforms: Exynos7
and AMD.
The Broadcom USB 3.0 Device Controller IP is now
supported and so is PLX USB338x, which means DWC3
has lost is badge as the only USB 3.0 peripheral
IP supported on Linux.
Thanks for Tony Lindgren's work, we can now have
a distro-like kernel where all MUSB glue layers
can be built into the same kernel (statically
or dynamically linked) and it'll work in PIO (DMA
will come probably on v3.20).
Other than these, the usual set of cleanups and
non-critical fixes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WYyZ
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.19 merge window
This time, a very pull request with 216 non-merge
commits. Most of the commits contained here are
sparse or coccinelle fixes ranging from missing
'static' to returning 0 in case of errors.
More importantly, we have the removal the now
unnecessary 'driver' argument to ->udc_stop().
DWC2 learned about Dual-Role builds. Users of
this IP can now have a single driver built for
host and device roles.
DWC3 got support for two new HW platforms: Exynos7
and AMD.
The Broadcom USB 3.0 Device Controller IP is now
supported and so is PLX USB338x, which means DWC3
has lost is badge as the only USB 3.0 peripheral
IP supported on Linux.
Thanks for Tony Lindgren's work, we can now have
a distro-like kernel where all MUSB glue layers
can be built into the same kernel (statically
or dynamically linked) and it'll work in PIO (DMA
will come probably on v3.20).
Other than these, the usual set of cleanups and
non-critical fixes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch adds missed resets property for CSR SiRFatlasVI SPI nodes.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
this patch adds missed resets property for CSR SiRFatlasVI Video Post
Processor(VPP) node.
Signed-off-by: Renwei Wu <renwei.wu@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
this patch adds missed resets property for CSR SiRFprimaII Video Post
Processor(VPP) node.
Signed-off-by: Renwei Wu <renwei.wu@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
this patch adds missed resets property for CSR SiRFprimaII GPS
related nodes.
Signed-off-by: Tao Huang <Tao.Huang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
The I2S controller can use the external clock as reference clock with
master mode. But based on different hardware or software design, this
external clock might be needed or not needed.
So the external input pin can be an independent pinctrl group, and the
card driver can decice to get it or not.
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The I2S controller can output mclk to external audio codec. But by
hardware design, some codecs need mclk and some codecs do not need
mclk. So the mclk pin can be an independent pinctrl group, and the
card driver can get it or not based on boards.
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
we have done that for atlas6 in commit ed36c1a, 086b8904 etc. here we
do same things for prima2.
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
A few patches that should go through the clock tree, mostly fixes, cleanups,
and new clocks additions to start to support the A80.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Krm9
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clocks-for-3.19' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into clk-next
Allwinner Clocks additions for 3.19
A few patches that should go through the clock tree, mostly fixes, cleanups,
and new clocks additions to start to support the A80.
When a thermal temperature is invoked use the CRU to reset the chip
on rk3288-evb boards. TSHUT is low active on these boards.
Signed-off-by: Caesar Wang <caesar.wang@rock-chips.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
If for some reason we are unable to shut it down in orderly fashion
(kernel is stuck holding a lock or similar), then hardware TSHUT will
reset it.
If the temperature is over 95C over a period of time the thermal shutdown
of the tsadc is invoked with can either reset the entire chip via the CRU,
or notify the PMIC via a GPIO. This should be set in the specific board.
Signed-off-by: Caesar Wang <caesar.wang@rock-chips.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch changes a dtsi file to contain the thermal data
on RK3288 and later SoCs. This data will
enable a thermal shutdown over 90C.
Signed-off-by: Caesar Wang <caesar.wang@rock-chips.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
DCAN1 is routed to CAN port (J11) when Profile 1 is selected on the
profile selection switch.
Provide information for DCAN1 pins and node but keep it disabled
by default. User has to manually enable it if Profile 1 is chosen.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add "raminit-syscon" property to specify the RAMINIT register.
Add clock information.
Rename can nodes from "d_can" to "can" to be compliant
with the ePAPR specs.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use syscon regmap to expose the Control module register space.
This register space is shared between many users e.g. DCAN, USB, display, etc.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add DCAN support for AM437x GP EVM with both DCAN instances.
[Roger Q] Updated output pin to not use pull up.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use syscon regmap to expose the Control module register space.
This register space is shared between many users e.g. DCAN, USB, display, etc.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board has 2 CAN ports but only the first one can be used.
Enable the first CAN port.
WAKEUP0 pin doesn't have INPUT enable bit so we just disable
weak PULLs.
The second CAN port cannot be used without hardware modification
so we don't enable the second port.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board has 2 CAN ports but only the first one can be used.
Enable the first CAN port.
WAKEUP0 pin doesn't have INPUT enable bit so we just disable
weak PULLs.
The second CAN port cannot be used without hardware modification
so we don't enable the second port.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Display and DCAN drivers use syscon regmap to access some registers
in the CORE control area. Add the syscon regmap node for this
area.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Review of the u-boot sunxi simplefb patches has led to the decision that
u-boot should not use a specific path to find the nodes as this goes contrary
to how devicetree usually works.
Instead a platform specific compatible + properties should be used for this.
The simplefb bindings have already been updated to reflect this, this patch
brings the sunxi devicetree files in line with the new binding, and the
actual u-boot implementation as it is going upstream.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Avoid the parent pll for the mod-clk for de_be0 getting disabled when non of
the other users are enabled (which can happen when none of i2c, spi and mmc
are in use).
Note for now we point directly to the parent rather then to the de_be0 mod-clk
as that is not modelled in our devicetree yet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a simplefb template node for u-boot to further fill and activate.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a simplefb template node for u-boot to further fill and activate.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a simplefb template node for u-boot to further fill and activate.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a simplefb template node for u-boot to further fill and activate.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The apb2 clocks are actually the same as apb1 clocks on the other sunxi
platforms, hence compatible with "allwinner,sun4i-a10-apb1-clk".
Update the dtsi to use the new unified apb1 clk.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
With the new factors infrastructure in place, we can unify apb1 and
apb1_mux as a single clock now.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
[wens@csie.org: Change apb1 node label to "apb1"; reword commit title]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Mele M9 has an ethernet board, enable it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
PLL6 on sun6i has multiple outputs, just like the other sunxi platforms.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Mele M9 / A1000G quad has a blue status led, add support for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Mele M9 / A1000G quad uses both usb-ports, one goes to an internal
usb wifi card, the other to a build-in usb-hub, so neither need their
OHCI companion controller to be enabled since the are always connected at
USB-2 speeds.
The controller which is attached to the wifi also does not need a vbus
regulator.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This avoids it getting briefly turned off between when the regulator getting
registered and the ahci driver turning it back on, thus avoiding the disk
going into emergency head park mode.
Reported-by: Bruno Prémont <bonbons@linux-vserver.org>
Tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cubietruck uses different pin for the USB OTG VBUS that
is why we override the one defined in sunxi-common-regulators.dtsi
Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Until now the regulator nodes for powering USB VBUS
existed only for the two host controllers. Now the regulator
is added for USB OTG too.
Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the LeMaker Banana Pi, probing the external ethernet PHY connected
to the SoC's internal GMAC module sometimes fails. The PHY power
supply is handled via a GPIO-controlled regulator, and the existing
regulator startup-delay of 50000us is too short to make sure that the
PHY is always fully powered up when it is queried by phylib. Tests
have shown that to provide a reliable PHY detection, the startup-delay
has to be increased to at least 60000us. To have a certain safety margin
and to cater for manufacturing variations between different boards,
the delay gets set to 100000us as discussed on the linux-arm-kernel
mailinglist.
Signed-off-by: Karsten Merker <merker@debian.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Roman Byshko <rbyshko@gmail.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Carlo Caione <carlo@caione.org>
Acked-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Roman Byshko <rbyshko@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Zoltan HERPAI <wigyori@uid0.hu>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Carlo Caione <carlo@caione.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Zoltan HERPAI <wigyori@uid0.hu>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: FUKAUMI Naoki <naobsd@gmail.com>
The A80 Optimus board exposes uart4 on the GPIO expansion header.
Enable it so we can use it.
Also enable the internal pull-ups, as there doesn't seem to be
external pull-up resistors for pins on the expansion header.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
uart4 only has one possible pinmux setting on the A80 SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A80 Optimus board has 3 usable LEDs that are controlled via GPIO.
This patch adds support for 2 of them which are driver by GPIOs in the
main pin controller. The remaining one uses GPIO from the R_PIO
controller, which we don't support yet.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
i2c3 is exposed on the GPIO extension header. Enable it so we can use it.
Also enable internal pull-ups on the pins, as they don't seem to have
external pull-up resistors.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
i2c3 has only one possible pinmux setting on the A80 SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A80 has 5 i2c controllers in the main processor block.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Thierry Reding