In preparation for future SoCs, move kona_l2_cache_init() from board
specific board_bcm281xx.c to shared kona.c, so multiple SoC families
can make use of it. Also change the return type to "void", since we
never look at the return code anyway.
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Signed-off-by: Matt Porter <mporter@linaro.org>
This patch renames a few symbols that needlessly used "11351" rather
than "281xx" in their names.
Support for the bcm11351 board is being removed from the kernel, and
the family of boards is more properly referred to as "bcm281xx".
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Signed-off-by: Matt Porter <mporter@linaro.org>
Without this patch I am getting a unhandled fault exception like this
one after "Freeing unused kernel memory":
Freeing unused kernel memory: 1260K (c02c1000 - c03fc000)
Unhandled fault: imprecise external abort (0x1c06) at 0xb6f89005
Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000007
The address which is here 0xb6f89005 changes from boot to boot, with a
new build the changes are bigger. With kernel 3.10 I have also seen
this fault at different places in the boot process, but starting with
3.11 they are always occurring after the "Freeing unused kernel memory"
message. I never was able to completely boot to userspace without this
handler. The abort code is constant 0x1c06. This fault just happens
once in the boot process I have never seen it happing twice or more.
I also tried changing the CPSR.A bit to 0 in init_early, with this code
like Afzal suggested, but that did not change anything:
asm volatile("mrs r12, cpsr\n"
"bic r12, r12, #0x00000100\n"
"msr cpsr_c, r12" ::: "r12", "cc", "memory");
Disabling the L2 cache by building with CONFIG_CACHE_L2X0 unset did not
help.
This workaround was copied from the vendor code including most of the
comments. It says it they think this is caused by the CFE boot loader
used on this device. I do not have any access to any datasheet or
errata document to check this.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Christian Daudt <bcm@fixthebug.org>
Signed-off-by: Matt Porter <mporter@linaro.org>
This patch adds support for the BCM5301X/BCM470X SoCs with an ARM CPUs.
Currently just booting to a shell is working and nothing else, no
Ethernet, wifi, flash, ...
I have some pending patches to make Ethernet work for this device.
Mostly device tree support for bcma is missing.
This SoC is used in small office and home router with Broadcom SoCs
it's internal name is Northstar. This code should support the BCM4707,
BCM4708, BCM4709, BCM53010, BCM53011 and BCM53012 SoC. It uses one or
two ARM Cortex A9 Cores, some highlights are 2 PCIe 2.0 controllers,
4 Gigabit Ethernet MACs and a USB 3.0 host controller.
This SoC uses a dual core CPU, but this is currently not implemented.
More information about this SoC can be found here:
http://www.anandtech.com/show/5925/broadcom-announces-bcm4708x-and-bcm5301x-socs-for-80211ac-routers
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Christian Daudt <bcm@fixthebug.org>
Signed-off-by: Matt Porter <mporter@linaro.org>
The symbol is an orphan, get rid of it.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
Signed-off-by: Matt Porter <mporter@linaro.org>
Move the bcm2835 board file into the mach-bcm directory. This allows us
to get rid of the mach-bcm2835 directory with the associated Kconfig
and Makefile.
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
[swarren, adjust defconfig so ARCH_BCM2835 still gets enabled]
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Multi-platform requires various kconfig options to be selected, so
platforms don't need to select them individually.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Adds pinctrl driver for Broadcom Capri (BCM281xx) SoCs.
v4: - PINCTRL selected in Kconfig, PINCTRL_CAPRI selected in bcm_defconfig
- make use of regmap
- change CAPRI_PIN_UPDATE from macro to inline function.
- Handle pull-up strength arg in Ohm instead of enum
v3: Re-work driver to be based on generic pin config. Moved config selection
from Kconfig to bcm_defconfig.
v2: Use hyphens instead of underscore in DT property names.
Signed-off-by: Sherman Yin <syin@broadcom.com>
Reviewed-by: Christian Daudt <bcm@fixthebug.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJScKOTAAoJEPYb7NoJr+nL+fwP/1bZKlbqYURXdrjLxHTZGKp3
WBpo8KUYp80nAZpw1SLoOk/78ciulQ0VLifWMebzMd/1qXXnek71jfYusbSb7MeM
e70y9TRtXrfkDPxL12XTXIf6F7JieGtVx0S2jJsGsofmM0w6b723KwZAYZgxACYB
Ec7TSzwaTlBBCI+ZyouS8e4CkS0x/0Mpkj8Ym8FDhKnwTs/mtD9kOcgVBzfz0Bt8
ExtiAsASeDvxUq5zskOiGiEhaNlhbQHd8etLIHEBTRreYQRg8nWTI+fdKKqwHKi0
qHm7p/ZcVQUgqf/2EjEfbEa0sQrQKrH82oaJirY3A6QrIEVQ5OVZCThkcvVV5Bxo
w1jDJcxYl2PEM/awR1YkRT3KQKb13J2PxbLFTYnKyhKgZz4mvB/NnjI1AuskTiS8
ddYfJ5apOqtZBqIYQvM6fv69mSWNinhmOqze14ulxGn+U6CVEYsGcQY1QvgA7T+c
0JAAUJwgRsJ+jIDjzx4EJFYCEpdRY8NAKNnZmPr8maP7DIttsbZd0KjWTTqg1Y1N
RHJkxJtnSxJYxfXkgpADJJNjcPdYxqfoYSpcRrGpFM3XLyCPKu2FiahpACyjua3W
JPzRGuYr4I51D16uHiYLxkDSwBKLYBlzyi5bzb+hed9nhoeynvOYtZZkuVgqVRKT
QJwnbUpxU1m870cNpAm/
=fAes
-----END PGP SIGNATURE-----
Merge tag 'bcm-for-3.13-soc2' of git://github.com/broadcom/bcm11351 into next/soc
From Christian Daudt, BCM changes for 3.13/soc. Mostly cleanups and
renaming of kernel config options, pushing down the mobile platforms
one level in the naming scheme, keeping ARCH_BCM as a wider family
config option.
* tag 'bcm-for-3.13-soc2' of git://github.com/broadcom/bcm11351:
ARM: bcm_defconfig: Run "make savedefconfig"
ARM: bcm281xx: Add ARCH Timers to config
rename ARCH_BCM to ARCH_BCM_MOBILE (mach-bcm)
ARM: bcm281xx: more descriptive machine string
ARM: bcm281xx: Enable GPIO driver
Signed-off-by: Olof Johansson <olof@lixom.net>
Add HAVE_ARM_ARCH_TIMER to Broadcom Kconfig as it is
required for some Mobile SoCs.
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
Reviewed-by: Markus Mayer <mmayer@broadcom.com>
Reviewed-by: Mark Hambleton <mahamble@broadcom.com>
Reviewed-by: James King <jamesk@broadcom.com>
Currently ARCH_BCM has been used for Broadcom
Mobile V7 based SoCs. In order to allow other Broadcom
SoCs to also use mach-bcm directory and files, this patch
renames the original ARCH_BCM to ARCH_BCM_MOBILE, and
uses ARCH_BCM to define any Broadcom chip residing
in mach-bcm directory.
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
Acked-by: Olof Johansson <olof@lixom.net>
Changes from v2:
- switch ARCH_MULTIPLATFORM from select to depends
- remove 'default y' from BCM_MOBILE
Changes from v1:
- fix alpha ordering in dts/Makefile
- break into 4 patches for separate subsys
Add SoC model to DT_MACHINE_START string.
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
Reviewed-by: Markus Mayer <mmayer@broadcom.com>
Reviewed-by: Mark Hambleton <mahamble@broadcom.com>
Reviewed-by: James King <jamesk@broadcom.com>
Turn on the bcm281xx GPIO driver in the kernel configuration.
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Christian Daudt <csd@broadcom.com>
With arch/arm calling of_clk_init(NULL) and clocksource_of_init()
this is no longer needed. The former is useful because we can make
use of dummy fixed clocks for drivers until the bcm281xx common
clock driver is ready.
Signed-off-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Acked-by: Christian Daudt <csd@broadcom.com>
The current bcm_kona_smc_init function throws a BUG_ON if there's no SMC
device node defined in the device tree.
Since secure API access is optional depending the chip configuration,
fix this by allowing the rest of the code to run even if there's no SMC
device node defined
Signed-off-by: Christian Daudt <csd@broadcom.com>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
[ this is a follow-up to this discussion:
http://archive.arm.linux.org.uk/lurker/message/20130730.230827.a1ceb12a.en.html ]
This patchset renames all uses of "bcm," name bindings to
"brcm," as they were done prior to knowing that brcm had
already been standardized as Broadcom vendor prefix
(in Documentation/devicetree/bindings/vendor-prefixes.txt).
This will not cause any churn on devices because none of
these bindings have made it into production yet.
Signed-off-by: Christian Daudt <csd@broadcom.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
In order to support multiple SoC models in the mach-bcm
directory, board_bcm.c is being renamed board_bcm281xx.c
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Signed-off-by: Christian Daudt <csd@broadcom.com>
This patch adds the code needed to trigger a reboot on the bcm281xx
family.
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Alex Elder <alex.elder@linaro.org>
Acked-by: Christian Daudt <csd@broadcom.com>
Commit ebafed7a ("ARM: irq: Call irqchip_init if no init_irq function is
specified") removed the need to explictly setup the init_irq field in
the machine description when using only irqchip_init. Remove that
declaration for bcm281xx as well.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Christian Daudt <csd@broadcom.com>
Two platforms, bcm and exynos have their own firmware interfaces using
the "secure monitor call", this adds support for those.
We had originally planned to have a third set of patches in here, which
would extend support for the existing generic "psci" call that is used
on multiple platforms as well as Xen and KVM guests, but that ended up
getting dropped because the patches were not ready in time.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=68m5
-----END PGP SIGNATURE-----
Merge tag 'firmware-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM platform specific firmware interfaces from Olof Johansson:
"Two platforms, bcm and exynos have their own firmware interfaces using
the "secure monitor call", this adds support for those.
We had originally planned to have a third set of patches in here,
which would extend support for the existing generic "psci" call that
is used on multiple platforms as well as Xen and KVM guests, but that
ended up getting dropped because the patches were not ready in time."
* tag 'firmware-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: bcm: mark bcm_kona_smc_init as __init
ARM: bcm281xx: Add DT support for SMC handler
ARM: bcm281xx: Add L2 cache enable code
ARM: EXYNOS: Add secure firmware support to secondary CPU bring-up
ARM: EXYNOS: Add IO mapping for non-secure SYSRAM.
ARM: EXYNOS: Add support for Exynos secure firmware
ARM: EXYNOS: Add support for secure monitor calls
ARM: Add interface for registering and calling firmware-specific operations
The bcm_kona_smc_init function references the bcm_kona_smc_ids variable
that is marked __initconst, so the function itself has to be __init
to avoid this build error:
WARNING: arch/arm/mach-bcm/built-in.o(.text+0x12c): Section mismatch in reference from the function bcm_kona_smc_init() to the (unknown reference) .init.rodata:(unknown)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Christian Daudt <csd@broadcom.com>
- Adds a module to provide calls into secure monitor mode
- Uses this module to make secure monitor calls to enable L2 cache.
Updates from V1:
- Split DT portion into separate patch
- replace #ifdef-ed L2 code with "if".
- move init call to board init
Signed-off-by: Christian Daudt <csd@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
This adds support for the Broadcom timer, used in the following SoCs:
BCM11130, BCM11140, BCM11351, BCM28145, BCM28155
Updates from V6:
- Split DT portion into a separate patch
Updates from V5:
- Rebase to latest arm-soc/for-next
Updates from V4:
- Switch code to use CLOCKSOURCE_OF_DECLARE
Updates from V3:
- Migrate to 3.9 timer framework updates
Updates from V2:
- prepend static fns + fields with kona_
Updates from V1:
- Rename bcm_timer.c to bcm_kona_timer.c
- Pull .h into bcm_kona_timer.c
- Make timers static
- Clean up comment block
- Switched to using clockevents_config_and_register
- Added an error to the get_timer loop if it repeats too much
- Added to Documentation/devicetree/bindings/arm/bcm/bcm,kona-timer.txt
- Added missing readl to timer_disable_and_clear
Note: bcm,kona-timer was kept as the 'compatible' field to make it
specific enough for when there are multiple bcm timers (bcm,timer is
too generic).
Signed-off-by: Christian Daudt <csd@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
In drivers/gpio/Kcong, ARCH_REQUIRE_GPIOLIB selects GPIOLIB which in
turn selects GENERIC_GPIO. So GENERIC_GPIO will be selected
automatically for those platforms that select ARCH_REQUIRE_GPIOLIB.
Remove the redundant 'select GENERIC_GPIO' for platforms that already
select ARCH_REQUIRE_GPIOLIB at either mach or plat level.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This creates irqchip initialization infrastructure from Thomas
Petazzoni. The VIC and GIC irqchip code is moved to drivers/irqchips
and adapted to use the new infrastructure. All DT enabled platforms
using GIC and VIC are converted over to use the new irqchip_init.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQ8ZobAAoJEMhvYp4jgsXiihIH/2VvxmSHZb0e3jN6AR0B42b7
9EwX0IE0B23t91hNTwdzzmTJQYA7pMmWkgHNfd3vIeqSepJAmrVv/gp4iM9CtPwE
KNh+kDWOK2ZsOH4Vb0lYRJHN8WQOIQHuCUr9+MdYLNOgf/pPL6G/Y9kv9A1e7fTC
W+tFRjC5N1ilZMGyowX12L1wnwDk6kHzed6YV6bskC17cZ9/pg8PhSVbM4A/3kAv
NXYKqbXJb+eCsWGXg/knZXOL6V9gBwvVYoe4O9X3nQ0226AWB9caad8l8tchAjRB
fmrYF1tbkpOWPnLxhvQy5b5MJichJgTMJHh7RgiEcc/3f63kOljjlx4QKiqHvT0=
=q7gm
-----END PGP SIGNATURE-----
Merge tag 'gic-vic-to-irqchip' of git://sources.calxeda.com/kernel/linux into next/cleanup
From Rob Herring:
Initial irqchip init infrastructure and GIC and VIC clean-ups
This creates irqchip initialization infrastructure from Thomas
Petazzoni. The VIC and GIC irqchip code is moved to drivers/irqchips
and adapted to use the new infrastructure. All DT enabled platforms
using GIC and VIC are converted over to use the new irqchip_init.
* tag 'gic-vic-to-irqchip' of git://sources.calxeda.com/kernel/linux:
irqchip: Move ARM vic.h to include/linux/irqchip/arm-vic.h
ARM: picoxcell: use common irqchip_init function
ARM: spear: use common irqchip_init function
irqchip: Move ARM VIC to drivers/irqchip
ARM: samsung: remove unused tick.h
ARM: remove unneeded vic.h includes
ARM: remove mach .handle_irq for VIC users
ARM: VIC: set handle_arch_irq in VIC initialization
ARM: VIC: shrink down vic.h
irqchip: Move ARM gic.h to include/linux/irqchip/arm-gic.h
ARM: use common irqchip_init for GIC init
irqchip: Move ARM GIC to drivers/irqchip
ARM: remove mach .handle_irq for GIC users
ARM: GIC: set handle_arch_irq in GIC initialization
ARM: GIC: remove direct use of gic_raise_softirq
ARM: GIC: remove assembly ifdefs from gic.h
ARM: mach-ux500: use SGI0 to wake up the other core
arm: add set_handle_irq() to register the parent IRQ controller handler function
irqchip: add basic infrastructure
irqchip: add to the directories part of the IRQ subsystem in MAINTAINERS
Fixed up massive merge conflicts with the timer cleanup due to adjacent changes:
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/mach-bcm/board_bcm.c
arch/arm/mach-cns3xxx/cns3420vb.c
arch/arm/mach-ep93xx/adssphere.c
arch/arm/mach-ep93xx/edb93xx.c
arch/arm/mach-ep93xx/gesbc9312.c
arch/arm/mach-ep93xx/micro9.c
arch/arm/mach-ep93xx/simone.c
arch/arm/mach-ep93xx/snappercl15.c
arch/arm/mach-ep93xx/ts72xx.c
arch/arm/mach-ep93xx/vision_ep9307.c
arch/arm/mach-highbank/highbank.c
arch/arm/mach-imx/mach-imx6q.c
arch/arm/mach-msm/board-dt-8960.c
arch/arm/mach-netx/nxdb500.c
arch/arm/mach-netx/nxdkn.c
arch/arm/mach-netx/nxeb500hmi.c
arch/arm/mach-nomadik/board-nhk8815.c
arch/arm/mach-picoxcell/common.c
arch/arm/mach-realview/realview_eb.c
arch/arm/mach-realview/realview_pb1176.c
arch/arm/mach-realview/realview_pb11mp.c
arch/arm/mach-realview/realview_pba8.c
arch/arm/mach-realview/realview_pbx.c
arch/arm/mach-socfpga/socfpga.c
arch/arm/mach-spear13xx/spear1310.c
arch/arm/mach-spear13xx/spear1340.c
arch/arm/mach-spear13xx/spear13xx.c
arch/arm/mach-spear3xx/spear300.c
arch/arm/mach-spear3xx/spear310.c
arch/arm/mach-spear3xx/spear320.c
arch/arm/mach-spear3xx/spear3xx.c
arch/arm/mach-spear6xx/spear6xx.c
arch/arm/mach-tegra/board-dt-tegra20.c
arch/arm/mach-tegra/board-dt-tegra30.c
arch/arm/mach-u300/core.c
arch/arm/mach-ux500/board-mop500.c
arch/arm/mach-ux500/cpu-db8500.c
arch/arm/mach-versatile/versatile_ab.c
arch/arm/mach-versatile/versatile_dt.c
arch/arm/mach-versatile/versatile_pb.c
arch/arm/mach-vexpress/v2m.c
include/asm-generic/vmlinux.lds.h
Convert all GIC DT initialization over to use common irqchip_init
function.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Now that the GIC initialization sets up the handle_arch_irq pointer, we
can remove it for all machines and make it static.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Now that the only field in struct sys_timer is .init, delete the struct,
and replace the machine descriptor .timer field with the initialization
function itself.
This will enable moving timer drivers into drivers/clocksource without
having to place a public prototype of each struct sys_timer object into
include/linux; the intent is to create a single of_clocksource_init()
function that determines which timer driver to initialize by scanning
the device dtree, much like the proposed irqchip_init() at:
http://www.spinics.net/lists/arm-kernel/msg203686.html
Includes mach-omap2 fixes from Igor Grinberg.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
In order to start upstreaming Broadcom SoC support, create
a starting hierarchy, arch and dts files.
The first support SoC family that is planned is the
BCM281XX (BCM11130/11140/11351/28145/28155) family of dual A9 mobile
SoC cores.
This code is just the skeleton code for get the machine upstreamed. It
has been made MULTIPLATFORM compatible.
Next steps
----------
Upstream a basic set of drivers - sufficient for a console boot to
ramdisk. These will includer timer, gpio, i2c drivers.
After this basic set, we will proceed with a more comprehensive set
of drivers for the 281XX SoC family.
v2 patch mods
--------
- Remove l2x0_of_init call as there were problems with the code.
A separate patch will be submitted with cache init code
- Rename capri files and refs to bcm281xx-based names
- Add bcm281xx binding doc
- various misc cleanups
v3 patch mods
-------------
- Remove extra #include lines
- Remove remaining references to capri
- dt uart chipset string added
- cleaned up chip # references
v4 patch mods
-------------
- swap order of compatible definitions for uart
- fix typo
v5 patch mods
-------------
- Rename bcm281xx to bcm11351 in dts+code,
leaving references to bcm281xx only in help+comments.
v6 patch mods
-------------
- fix typo in uart 'compatible' string
Signed-off-by: Christian Daudt <csd@broadcom.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Markus Mayer