There are 2 separate clock outputs available in the SoC for external sensors.
These two clocks can be shared among all FIMC entities and there is
currently no any arbitration of the clocks in the driver.
So make the capture driver not touching these clocks and let them be
be properly handled at the media device driver level, enabling proper
arbitration between FIMC entities.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do not register video nodes during FIMC device probe. Also make
fimc_register_m2m_device() public for use by the media device driver.
The video nodes are to be registered during the media device driver
initialization, altogether with the subdev devnodes. The video
capture nodes need to be registered as last ones when the remaining
pipeline elements are already initialized.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add intialization of the media entities for video capture
and mem-to-mem video nodes. The mem-to-mem entity has no pads
whereas the capture entity has single sink pad.
Also clean up the video node naming for consistency.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do not resume the device during system resume if it was idle
before system suspend, as this causes resume from suspend
to RAM failures on Exynos4. For this purpose runtime PM and
system sleep helpers are separated.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On the SoCs this driver is intended to support the are three separate
pins to supply the MIPI-CSIS subsystem: 1.1V or 1.2V, 1.8V and power
supply for an internal PLL.
This patch adds support for two separate voltage supplies to cover
properly board configurations where PMIC requires to configure
independently each external supply of the MIPI-CSI device. The 1.8V
and PLL supply are assigned a single "vdd18" regulator supply name
as it seems more reasonable than creating separate regulator supplies
for them.
While at here stop using the 'fixed_phy_vdd' platform_data field.
It has been introduced for boards where the MIPI-CSIS supplies are
not controllable. However it is not needed as those boards can use
the dummy regulator.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add runtime PM and system sleep support in the memory-to-memory
driver. It's required to enable the FIMC operation on Exynos4
SoCs. This patch prevents system boot failure when the driver
is compiled in, as it now tries to access its I/O memory without
first enabling the corresponding power domain.
The camera capture device suspend/resume is not fully covered,
the capture device is just powered on/off during the video
node open/close. However this enables it's normal operation
on Exynos4 SoCs.
[mchehab@redhat.com: fix a small checkpatch error]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch changes the order of operations during stream on call. Now the
buffers are first queued to the driver and then the start_streaming method
is called.
This resolves the most common case when the driver needs to know buffer
addresses to enable dma engine and start streaming. Additional parameter
to start_streaming method have been added to simplify drivers code. The
driver are now obliged to check if the number of queued buffers is high
enough to enable hardware streaming. If not - it can return an error. In
such case all the buffers that have been pre-queued are invalidated.
This patch also updates all videobuf2 clients to work properly with the
changed order of operations.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
CC: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
CC: Hans Verkuil <hverkuil@xs4all.nl>
CC: Tomasz Stanislawski <t.stanislaws@samsung.com>
CC: Sylwester Nawrocki <s.nawrocki@samsung.com>
CC: Kamil Debski <k.debski@samsung.com>
CC: Jonathan Corbet <corbet@lwn.net>
CC: Josh Wu <josh.wu@atmel.com>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Paul Mundt <lethal@linux-sh.org>
Tested-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the correct 'dma_addr' name for the buffer address. 'paddr' suggested
that this is the physical address in system memory. For most ARM platforms
these two are the same, but this is not a generic rule. 'dma_addr' will
also point better to dma-mapping api.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Plane sizes array was declared as unsigned long[], while unsigned int is
more than enough for storing size of the video buffer. This patch reduces
the size of the array by definiting it as unsigned int[].
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Standardize the remaining video drivers to return the API version
for the VIDIOC_QUERYCAP version, instead of a per-driver version.
Those drivers had the version updated more recently or are SoC
drivers. Even so, it doesn't sound a good idea to keep a per-driver
version control, so, let's use the per-subsystem version control
instead.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With multi-planar formats fmt.pix_mp member of struct v4l2_format
should be used rather than fmt.pix. Fix find_fmt() function to do
the right thing.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The buf_init buffer queue operation is optional and
buffer_init() does nothing, remove it.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Avoid dereferencing of NULL f->fmt. Correct size of the allocated
buffer in case the crop rectangle is smaller than the bounds
rectangle (configured with S_FMT). Also remove redundant check
for *num_buffer == 0 as this case is handled in videobuf2.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the subdev driver for the MIPI CSIS units available in S5P and
Exynos4 SoC series. This driver supports both CSIS0 and CSIS1
MIPI-CSI2 receivers.
The driver requires Runtime PM to be enabled for proper operation.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (42 commits)
[media] media: vb2: correct queue initialization order
[media] media: vb2: fix incorrect v4l2_buffer->flags handling
[media] s5p-fimc: Add support for the buffer timestamps and sequence
[media] s5p-fimc: Fix bytesperline and plane payload setup
[media] s5p-fimc: Do not allow changing format after REQBUFS
[media] s5p-fimc: Fix FIMC3 pixel limits on Exynos4
[media] tda18271: update tda18271c2_rf_cal as per NXP's rev.04 datasheet
[media] tda18271: update tda18271_rf_band as per NXP's rev.04 datasheet
[media] tda18271: fix bad calculation of main post divider byte
[media] tda18271: prog_cal and prog_tab variables should be s32, not u8
[media] tda18271: fix calculation bug in tda18271_rf_tracking_filters_init
[media] omap3isp: queue: Don't corrupt buf->npages when get_user_pages() fails
[media] v4l: Don't register media entities for subdev device nodes
[media] omap3isp: Don't increment node entity use count when poweron fails
[media] omap3isp: lane shifter support
[media] omap3isp: ccdc: support Y10/12, 8-bit bayer fmts
[media] media: add missing 8-bit bayer formats and Y12
[media] v4l: add V4L2_PIX_FMT_Y12 format
cx23885: Fix stv0367 Kconfig dependency
[media] omap3isp: Use isp xclk defines
...
Fix up trivial conflict (spelink errurs) in drivers/media/video/omap3isp/isp.c
Add support for buffer timestamps and the sequence number in
the video capture driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make sure the sizeimage for 3-planar color formats is
width * height * 3/2 and the bytesperline is same for each
plane in case of a multi-planar format.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Protecting the color format with vb2_is_streaming() is not sufficient
as this prevents changing the format only after VIDIOC_STREAMON.
To prevent the color format reconfiguration as soon as buffers
are allocated use vb2_is_busy() instead.
Also make the videobuf queue ops structure static.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Correct pixel limits for the fourth FIMC entity on Exynos4 SoCs.
FIMC3 only supports the writeback input from the LCD mixer.
Also rename s5pv310 variant to exynos4 which is needed after
renaming s5pv310 series to Exynos4.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use pix_mp member of struct v4l2_format to return a format
description rather than pix. Also fill in the plane_fmt array.
This is a missing bit of conversion to the multiplanar API.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use pr_debug instead of printk so it is possible to control
debug traces at runtime.
E.g. to enable debug trace in file fimc-core.c use command:
echo -n 'file fimc-core.c +p' > /sys/kernel/debug/dynamic_debug/control
or
echo -n 'file fimc-core.c -p' > /sys/kernel/debug/dynamic_debug/control
to disable.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Allow the MIPI-CSI data alignment to be defined in the board setup
as it may be different across various camera sensors.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add num_clients field to struct s5p_fimc_isp_info to define exactly
size of clients array which simplifies a bit the sensors management.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rework the locking in m2m driver to assure proper operation on SMP systems.
When job_abort or stop_streaming was called to immediately shutdown
a memory-to-memory transaction video buffers scheduled for processing
were never returned to vb2 and v4l2_m2m_job_finish was not called
which led to hanging.
Correct this and also return the unprocessed buffers to vb2 marking
them as erroneous, in case the end of frame interrupt do not occur.
Reported-by: Sewoon Park <seuni.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In some cases fimc H/W did not stop although there were no output
buffers available. So the capture deactivation interrupt routine
is modified and the state of ST_CAPT_RUN is cleared only
in the LAST-IRQ call.
After LAST-IRQ is generated, H/W pointer will be skipped by 1 frame.
(reference by user manual) So, S/W pointer should be increased too.
Reviewed-by Jonghun Han <jonghun.han@samsung.com>
Signed-off-by: Sungchun Kang <sungchun.kang@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When is called fimc_stop_capture, it seems that wait_event_timeout
used improperly. It should be wake up by irq handler.
Reviewed-by Jonghun Han <jonghun.han@samsung.com>
Signed-off-by: Sungchun Kang <sungchun.kang@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes the value of FIFO_CTRL in MSCTRL.
Main-scaler has the value to specify a basis FIFO control of input DMA.
The description of FIFO_CTRL has been changed as below.
0 = FIFO Empty (Next burst transaction is possible when FIFO is empty)
1 = FIFO Full (Next burst transaction is possible except Full FIFO)
Value '1' is recommended to enhance the FIMC operation performance.
Reviewed-by: Jonghun Han <jonghun.han@samsung.com>
Signed-off-by: Hyunwoong Kim <khw0178.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds callback functions, stop_streaming and job_abort,
to abort or finish any DMA in progress. stop_streaming is called
by videobuf2 framework and job_abort is called by m2m framework.
ST_M2M_PEND state is added to discard the next job.
Reviewed-by: Jonghun Han <jonghun.han@samsung.com>
Signed-off-by: Hyunwoong Kim <khw0178.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Horizontal and vertical scaling range are according to the following equations.
If (SRC_Width >= 64 x DST_Width) { Exit(-1); /* Out of Horizontal scale range}
If (SRC_Height >= 64 x DST_Height) { Exit(-1); /* Out of Vertical scale range}
fimc_check_scaler_ratio() is used to check if horizontal and vertical
scale range are valid or not. To use fimc_check_scaler_ratio,
source and destination format should be set by VIDIOC_S_FMT.
And in case of scaling up, it doesn't have to check the scale range.
Reviewed-by: Jonghun Han <jonghun.han@samsung.com>
Signed-off-by: Hyunwoong Kim <khw0178.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The main scaler has four SFRs for main scaler ratio depending on FIMC version.
FIMC 4.x has only two SFRs and FIMC 5.x has four SFRs for main scaler.
Those are MainHorRatio, MainHorRatio_ext, MainVerRatio and MainverRatio_ext.
The FIMC 5.x has 15 bit resolution for scaling ratio as below.
{MainHorRatio,MainHorRatio_ext} = {[14:6],[5:0]}.
{MainVerRatio,MainVerRatio_ext} = {[14:6],[5:0]}.
MainHorRatio = CISCCTRL[24:16], MainHorRatio_ext = CIEXTEN[15:10]
MainVerRatio = CISCCTRL[8:0], MainVerRatio_ext = CIEXTEN[5:0]
This patch supports FIMC 4.x and FIMC 5.x using platform_device_id::driver_data.
Reviewed-by: Jonghun Han <jonghun.han@samsung.com>
Signed-off-by: Hyunwoong Kim <khw0178.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some color formats are mismatched in s5p-fimc driver.
CIOCTRL[1:0], order422_out, should be set 2b'00 not 2b'11
to use V4L2_PIX_FMT_YUYV. Because in V4L2 standard V4L2_PIX_FMT_YUYV means
"start + 0: Y'00 Cb00 Y'01 Cr00 Y'02 Cb01 Y'03 Cr01". According to datasheet
2b'00 is right value for V4L2_PIX_FMT_YUYV.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Manage the camera sensor clock in the host driver rather than
leaving this task for sensor drivers. The clock frequency
must be passed in the sensor's and host driver's platform data.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Map all (0, 90, 180, 270) deg counterclockwise rotation and
horizontal and vertical flip controls to (0, 90) deg rotation,
horizontal and vertical flip transformations available
in the device.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Increase the input DMA "successive burst count" to default
value 4 to improve DMA performance. Minor cleanup.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Prevent VIDIOC_STREAMON failing when s_stream callback is
not implemented by a sensor subdev driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove bus_width from s5p_fimc_isp_info data structure.
Determine camera data bus width based on mediabus pixel format.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change s3c_fimc.h header file name to s5p_fimc.h, replace s3c_fimc_*
names with s5p_fimc_*. s3c_fimc need to be reserved for S3C series
and s5p-fimc driver will not cover CAMIF devices in S3C SoC series.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Conversion to multiplanar color formats and minor cleanup.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Porting to videobuf 2 and minor cleanup.
Separate videobuf_queue_ops are are created for m2m
and capture video nodes.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
FIMC IP in S5Pv310 series has extended DMA status registers
and some bit fields are marked as reserved comparing to S5PC100/110.
Use correct registers for getting DMA write pointer in each SoC variant
supported by the driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replace V4L2_PIX_FMT_RGB24 code with V4L2_PIX_FMT_RGB32
since the hardware uses 24-bits for actual pixel data but pixels
are 4-byte aligned in memory.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Create separate vidioc_g_crop/vidioc_s_crop handlers for capture
video node and so image cropping parameters are properly queried
at FIMC input (image sensor) and not at FIMC output.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The argument isn't used anymore by the functions, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the v4l2_i2c_new_subdev* functions now supporting loading modules
based on modaliases, replace the hardcoded module name passed to those
functions by NULL in the cafe-ccic, via-camera and s5p-fimc drivers.
All corresponding I2C modules have been checked, and all of them include
a module aliases table with names corresponding to what the drivers
modified here use.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
> From: Dan Carpenter [mailto:error27@gmail.com]
>
> These are signed so instead of being 1 and 0 as intended they are -1 and
> 0. It doesn't cause a bug in the current code but Sparse warns about
> it:
>
> drivers/media/video/s5p-fimc/fimc-core.h:226:28:
> error: dubious one-bit signed bitfield
> struct fimc_scaler {
> - int scaleup_h:1;
> - int scaleup_v:1;
> - int copy_mode:1;
> - int enabled:1;
> + unsigned int scaleup_h:1;
> + unsigned int caleup_v:1;
> + unsigned int copy_mode:1;
> + unsigned int enabled:1;
In general I agree, however this patch would change scaleup_v:1
to caleup_v, so it cannot be applied in current form.
Here is the corrected patch:
Reported-by: Dan Carpenter <error27@gmail.com<
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There was an unlock missing if kzalloc() failed.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Enable FIMC operation on S5PC210 (S5PV310) SoCs. This a minimal
adaptation to obtain functionality of older FIMC IP revisions
(S5PC100, S5PC110) on S5PC210 SOcs.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a video device driver per each FIMC entity to support
the camera capture input mode. Video capture node is registered
only if CCD sensor data is provided through driver's platfrom data
and board setup code.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is not necessary to lock both capture and output buffer queue while
setting format for single queue.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to errorneous swapping of image dimensions the rotation
control was not handled properly in subsequent calls.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Register access functions refactored for camera capture interface
control. Removed the workqueue since it was only useful for FIFO
output mode which is not supported at this time.
Fixed errors on module unload. Comments and whitespace cleanup.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Missed a few init functions on non-Intel platforms the first time :-(
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix DMA engine pixel offset calculation for 3-planar YUV formats.
On S5PV210 SoCs horizontal offset is applied as number of pixels,
not bytes per line.
[mchehab@redhat.com: CodingStyle cleanup]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If we return directly here then we miss out on some mutex_unlock()s
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver exports a video device node per each camera interface/
video postprocessor (FIMC) device contained in Samsung S5P SoC series.
The driver is based on v4l2-mem2mem framework.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sylwester Nawrocki